Página 1 de 8

TM110719 - 9360R, 9410R, 9460R, 9510R, and 9560R Tractors Repair

Remove 13.5 L Engine

Remove 13.5 L Engine

1.
RXA0120449-UN: Battery Ground Cable

RXA0120450-UN: Radiator Drain

LEGEND:

A - Ground Cable
B - Starter Wiring
C - Radiator Drain

Disconnect battery ground cable (A).

2. Disconnect starter wiring (B).

3. Drain coolant from radiator drain (C) and block.

4.

CAUTION:

Hood is heavy. Use care with hood to prevent personal injury.

NOTE:

Hood may be raised to service position or removed from tractor. (See Position Hood Forward or Remove
and Install Hood in Section 80, Group 05.)

Raise hood to service position.

5.
RXA0120455-UN: Left Side

RXA0120462-UN: Auxiliary Drive

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016

 Página 2 de 8

LEGEND:

A - Left-Hand Side Shield and Fingerguard

B - Charge Air Pipe
C - Accessory Drive Belt
D - Alternator
E - Air Conditioner Compressor
F - Fan Belt
G - Fan

Remove left-hand side shield and fingerguard (A).

6. Remove charge air pipe (B).

7. Remove accessory drive belt (C).

8. Disconnect fuel supply hose.

9. Remove alternator (D) and tie to outside left-hand frame.

10. Remove air conditioning compressor (E) without disconnecting lines and tie to outside left-hand frame.

11. Remove fan belt (F) and position fan (G) forward in shroud.

12.
RXA0120452-UN: Engine Controller

LEGEND:

A - Controller Cover
B - Chassis Harness Connector

Remove control unit cover (A).

13. Disconnect chassis wiring connector (B) from engine control unit.

14.
RXA0120454-UN: Right Side Shield

RXA0120484-UN: Heater Lines

LEGEND:

A - Right-Hand Side Shield and Fingerguard

B - Upper Radiator Hose
C - Lower Radiator Hose
D - Charge Air Pipe
E - Fan Driven Sheave Assembly
F - Heater Lines

Remove right-hand side shield and fingerguard (A).

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016

 Página 3 de 8

15. Disconnect upper and lower radiator hoses (B and C).

16. Remove charge air intake pipe (D).

17. Remove fan driven assembly (E). (See Remove and Install VARI-COOL™ Fan Driven Assembly—13.5 L Engine in Section
30, Group 15).

18. Remove heater lines (F).

19.
RXA0120477-UN: Deaeration Lines

LEGEND:

A - Deaeration Tank
B - Hoses
C - Line Support
D - Cap Screws (4 used)

Label and disconnect hoses (B) from deaeration tank (A) and front connections.

20. Remove cap screws (D) and line support (C).

21.
RXA0120481-UN: Drive Shaft Shield

RXA0120482-UN: Drive Shaft

LEGEND:

A - Shield
B - Cap Screws (12 used)
C - Torsional Drive Damper

Remove shield (A)

22. Disconnect torsional drive damper (C) from flywheel using JDG820 Flywheel Rotation Tool to gain access to cap screws (B).

23. Pry torsional drive damper rearward.

24.
RXA0140002-UN: Exhaust Pipe

LEGEND:

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016

 Página 4 de 8

A - Shield
B - Flange Clamps (2 used)
C - Exhaust Pipe

Remove shield (A).

25. Remove flange clamps (B) and remove exhaust pipe (C).

26.
RXA0140001-UN: Intake Pipe

LEGEND:

A - Sensor
B - Cap Screws (2 used)
C - Flange Clamp
D - Hose Clamp
E - Intake Pipe

Disconnect Sensor (A).

27. Remove cap screws (B).

28. Remove flange clamp (C) and hose clamp (D).

29. Remove intake pipe (E).

30.
RXA0140003-UN: Oil Tube

RXA0140004-UN: Oil Line

LEGEND:

A - Oil Tube Cap Screws (6 used)

B - Oil Tube
C - Cap Screw
D - Oil Line

Remove cap screws (A) and oil tube (B).

31. Remove cap screw (C) and oil line (D).

32.

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016

 Página 5 de 8

RXA0140005-UN: Bracket

Remove cap screws (A) and bracket (B).

33.

CAUTION:

Engine is heavy. Use ONLY recommended engine removal equipment to remove engine to prevent
personal injury.

IMPORTANT:

Use grade 10.9 cap screws for lift strap installation.

Cap screws are one time use only.

NOTE:

JDG11325P1 and JDG11325P2 are part of JDG11325 Rear Lifting Bracket .

RXA0140006-UN: Lower Rear Bracket

RXA0140007-UN: Upper Rear Bracket

RXA0139932-UN: Front Lifting Bracket

LEGEND:

A - JDG11325P1 Rear Lifting Bracket

B - M12 x 35 mm Rear Lifting Bracket Cap Screws (2 used)
C - JDG11325P2 Rear Lifting Bracket
D - M12 Rear Lifting Bracket Cap Screws (2 used)
E - JDG11324 Front Lifting Bracket
F - M12 Front Lifting Bracket Cap Screws (2 used)

For tractors equipped with IT4 Engines, perform the following:

 Install JDG11325P1 Rear Lifting Bracket (A) to cylinder head using M12 x 35 mm cap screws (B). Tighten to
specification.

Item Measurement Specification

Engine Lift Bracket Cap Screws— Torque 120 N·m

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016

 Página 6 de 8

13.5 L (90 lb.-ft.)

 Install JDG11325P2 Rear Lifting Bracket (C) using M12 cap screws (D). Tighten to specification.

Item Measurement Specification

Engine Lift Bracket Cap Screws— Torque 120 N·m

13.5 L (90 lb.-ft.)

 Install JDG11324 Front Lifting Bracket (E) to front of cylinder head using M12 cap screws (F). Tighten cap screws to
specification.

Item Measurement Specification

Engine Lift Bracket Cap Screws— Torque 120 N·m

13.5 L (90 lb.-ft.)

34.

CAUTION:

Engine is heavy. Use only the recommended engine removal equipment to remove engine to prevent a
personal injury.

IMPORTANT:

Use grade 10.9 cap screws for lift strap installation.

Cap screws are one time use only.

For tractors equipped with STAGE II Engines, perform the following:


RXA0091880-UN: Rear Bracket

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016

 Página 7 de 8

RXA0091909-UN: Front Bracket

LEGEND:

A - JDG10199 Rear Engine Lift Bracket

B - JDG10200 Front Engine Lift Bracket

Install JDG10199 Rear Engine Lift Bracket (A) on cylinder head using two M12 x 35 mm cap screws. Tighten cap
screws to specification.

Item Measurement Specification

Engine Lift Bracket Cap Screws— Torque 120 N·m

13.5 L (90 lb.-ft.)

 Install JDG10200 13.5L Front Engine Lift Bracket (B) to front of cylinder head. Tighten cap screws to specification.

Item Measurement Specification

Engine Lift Bracket Cap Screws— Torque 120 N·m

13.5 L (90 lb.-ft.)

35.
RXA0120483-UN: Engine Lift Sling

LEGEND:

C - JT07336 Engine Lift Sling

Install and adjust JT07336 Lift Sling (C) and support engine.

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016

 Página 8 de 8

36.
RXA0120493-UN: Engine Mounts

LEGEND:

A - Front Mount-to-Frame Cap Screw

B - Front Mount-to-Engine Cap Screw
C - Rear Mount-to-Frame Cap Screw

Remove front mount cap screws (A).

37. Loosen cap screws (B) for reassembly purposes.

38. Remove rear mount cap screws (C).

39. Carefully raise engine and rotate front of engine to left.

40. Remove engine from right-hand side of tractor.

LN71218,000076B-19-20140912

file://C:\ProgramData\Service ADVISOR\Temp\TM110719_09001faa8262efb3.html 17/03/2016