FTA1100J Diesel Engine Fire Pump Controllers
Product Description
• MAIN SWITCH IN MANUAL
• SYSTEM PRESSURE LOW
• ENGINE RUNNING
• ENGINE FAIL TO START
• ENGINE TEMPERATURE HIGH
• ENGINE OIL PRESSURE LOW
• ENGINE OVERSPEED
• ENGINE ALTERNATE ECM
• ENGINE FUEL INJECTOR MALFUNCTION
• FUEL LEVEL LOW
• AUTOMATIC SHUTDOWN DISABLED
• CHARGER MALFUNCTION
• BATTERY #1 TROUBLE
• BATTERY #2 TROUBLE
• Minimum Run Timer / Off Delay Timer
• Programmable Daylight Saving Time Option
• Weekly Test Timer
Description – Firetrol® combined automatic and manual • Engine Run Time Meter
Mark IIXG based diesel engine fire pump controllers are • Digital Pressure Display
intended for starting and monitoring fire pump diesel • USB Host Controller and Port
engines. They are suitable for use with both mechanical • Solid State Pressure Transducer
and electronic type engines. The controller is available for • Data Log
12 or 24 volt negative ground systems, using lead acid • Event Log (3000 events)
or Nickel-Cadmium batteries. The controller monitors, • Simultaneous Display of Battery Voltages, Charging
displays and records fire pump system information. Rates, AC Volts, Pressure and Alarm Messages
• Disk Error Message
Approvals – Firetrol fire pump controllers are listed by • Disk Near Full Message
Underwriters’ Laboratories, Inc., in accordance with • Pressure Error Message
UL218, Standard for Fire Pump Controllers, CSA, Standard • Fail to Start Message
for Industrial Control Equipment (cUL), and approved by • Low Suction Pressure Message
Factory Mutual. They are built to meet or exceed the • Crank Cycle Status Indication (Displays Cranking Bat-
requirements of the approving authorities as well as tery, Number of Starting Attempts and Crank/Rest
NEMA and the latest editions of NFPA 20, Installation Time Remaining)
of Centrifugal Fire Pumps, and NFPA 70, National Electri- • 300 psi (20.7 bars) wet parts (solid state pressure
cal Code. transducer, solenoid valve, plumbing) for fresh water
applications
• NEMA Type 2 enclosure (IEC IP22)
Standard Features – The following are included as stan- • Each standard controller comes with user set options
dard with each controller: for:
• AC Line & Battery circuit breakers • AC Power Loss Start • Interlock Alarm
• Manual-Off-Auto selector switch • Low Pressure Aud. • Low Suction
• Manual test push-button • Main Sw. Mis-Set • Manual Test
• Two manual crank push-buttons • Pump Run Alarm • Remote Start
• Two 10 Amp battery chargers with 4 stage charging • User Defined Input • Weekly Test Setup
cycle, selectable AC voltage (110 / 220), selectable DC • Low Pump Rm Temp • Low Reservoir
voltage (12 / 24), and selectable battery type (Lead • Relief Valve Open • High Fuel Level
Acid, Ni-Cad 9/18 Cell, Ni-Cad 10/20 Cell) • High Reservoir
• Door mounted display/interface panel featuring a 128
x 64 pixel backlit LCD graphical display, Membrane
Type User Control Push-buttons and easy to read LED
Indicators for:
• AC POWER AVAILABLE
• ALARM
• MAIN SWITCH IN AUTO
Special Enclosures -CPL Contacts for remote indication, system
-T NEMA Type 3R (IEC IP22), Painted Steel 115% over pressure (for use with PLD engines only)
-E NEMA Type 4 (IEC IP 66), Painted Steel -CTS Built-in low suction pressure alarm panel (Includes select-
-F NEMA Type 4X (IEC IP66) #304 Stainless able auto/manual reset, audible, visible and remote alarms
Steel, Brushed Finish and mounted and wired pressure switch)
-FXP NEMA Type 4X (IEC IP66) #304 Stainless -EE Additional contacts for remote indication, engine trouble - 1
Steel, Painted Finish set provided as standard
-FD NEMA Type 4X (IEC IP66) #316 Stainless -EF Additional contacts for remote indication, main switch
Steel, Brushed Finish mis-set - 1 set provided as standard
-FDB NEMA Type 4X (IEC IP66) #316 Stainless -EH Contacts for remote indication, relief valve discharge1
Steel, 12 Gauge, Seam Welded, -EJ Audible & Visible flow meter on alarm1
Brushed Finish -EK Contacts for remote indication, flow meter on1 (Requires
-FDP NEMA Type 4X (IEC IP66) #316 Stainless option -EJ)
Steel, Painted Finish -JR Visible jockey pump running indication
-G NEMA Type 12 (IEC IP54) -JT Audible and visible jockey pump trouble indication
-LC Contacts for remote indication, high fuel level1
Mounting Legs -LD Audible & Visible fuel spill alarm1
-N31 Standard 12” Mounting Legs -LE Contacts for remote indication, fuel spill1 (Requires option
-N31S 12” Mounting Legs, Stainless Steel -LD)
-LG Contacts for remote indication, reservoir high1
Anti-Condensation Space Heaters -PE Contacts for remote indication, low system pressure
-H 120 Volt Space Heater (Pump On Demand)
-J 120 Volt Space Heater with Thermostat
-K 120 Volt Space Heater with Humidistat Miscellaneous
-L 240 Volt Space Heater -AZ Low pump room temperature switch, mounted and wired
-M 240 Volt Space Heater with Thermostat -BA 220-240 Volt operation
-N 240 Volt Space Heater with Humidistat -EL Series pumping, high zone controller
-EM Series pumping, mid zone controller
Pressure Transducers, Solenoid Valves, Plumbing -EN Series pumping, low zone controller
-B 0-600 psi (0-41.4 bars) wet parts for fresh water applications -IEC CE Marking with Externally Mounted Wet Parts
-C 0-300 psi (0-20.7 bars) wet parts for copper corrosive -IECI CE Marking (Internal Wet Parts)
applications -OSP OSHPD Seismic Certification (State of California) (Requires
-D 0-600 psi (0-41.4 bars) wet parts for copper corrosive Option -SEI)
applications -S Tropicalization
-SEI Seismic Certification (in accordance with IBC)
Alarms -USBX External USB Port
-AC Additional contacts for remote indication, engine running - 2 -ZPA Customized, annual service display message (factory
sets provided as standard programmed)
-AJ Contacts for remote indication, engine overspeed -ZPN Serial Modbus RTU over Ethernet TCP/IP
-AK Contacts for remote indication, low oil pressure using 5150 Connectivity Module
-AL Contacts for remote indication, high water temperature -ZPM Serial Modbus RTU over 2-wire or 4-wire RS485
-AM Contacts for remote indication, engine failed to start
-AN Contacts for remote indication, battery / charger failure FTA1100-K1 Low fuel level switch, 16” max insertion length2
-AP Contacts for remote indication, main switch in manual FTA1100-K1-X High/Low fuel level switch - specify levels/tank
-AR Contacts for remote indication, main switch in off dimensions
-AS Contacts for remote indication, main switch in auto FTA1100-K2 Low fuel level switch, 25” max. insertion length2
-AT Contacts for remote indication, pump room trouble1 FTAK21 380-480 volt operation (transformer)2
-AV Contacts for remote indication, low pump room Export packaging (Wooden crating to conform to IPPC Standards)
temperature1
-AW Contacts for remote indication, reservoir low1
-AY Contacts for remote indication, low suction pressure1 1
- Initiating switches by others
-COM Visible low suction pressure alarm, 2
- Shipped loose for installation by the customer
Manual reset only (Includes reset push-button, initiating
pressure switch not included)1
