Scribd
Upload
358 views

Worksheet & Assignment

The document contains 11 practice problems related to strength of materials. The problems involve calculating stresses, strains, and deformations in various materials and structural components under different loading conditions. Key information includes the elastic moduli, shear moduli, cross-sectional areas, loads, and dimensional changes of the materials and structures described. The problems are to be solved by applying concepts of stress, strain, elasticity, shear, compression, tension, and combined loading.

Uploaded by

Adnan Shafi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
358 views

Worksheet & Assignment

The document contains 11 practice problems related to strength of materials. The problems involve calculating stresses, strains, and deformations in various materials and structural components under different loading conditions. Key information includes the elastic moduli, shear moduli, cross-sectional areas, loads, and dimensional changes of the materials and structures described. The problems are to be solved by applying concepts of stress, strain, elasticity, shear, compression, tension, and combined loading.

Uploaded by

Adnan Shafi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

STRENGTH OF MATERIALS AASTU

Worksheet
1. An aluminum tube is rigidly fastened between a brass rod and steel rod. Axial loads are applied
as indicated in the figure. Determine the stresses in each material and total deformation. Take
Ea=70GPa, Eb=100GPa Es =200GPa

Ans: σb =28.57MPa, σa=5MPa, σs=12.5MPa, δ = - 0.142mm


2. The diameter of a specimen is found to reduce by 0.004mm when it is subjected to a tensile
force of 19kN. The initial diameter of the specimen was 20mm. Taking modulus of rigidity
as 40GPa determine the value of E and v.
Ans: E=110GPa, v=0.36
3. A circular bar of brass is to be loaded by a shear load of 30kN. Determine the necessary
diameter of the bars (a) in single shear (b) in double shear, if the shear stress in material must
not exceed 50MPa.
Ans: 27.6, 19.5mm
4. Determine the largest weight W that can be supported by the two wires shown. Stresses in
wires AB and AC are not to exceed 100MPa and 150MPa respectively. The cross sectional
areas of the two wires are 400mm2 for AB and 200mm2 for AC.

Ans: 33.4kN
5. The coupling shown in figure is constructed from steel of rectangular cross-section and is
designed to transmit a tensile force of 50kN. If the bolt is of 15mm diameter calculate:
a) The shear stress in the bolt;
b) The direct stress in the plate;
c) The direct stress in the forked end of the coupling.

GIRUM M. 1
STRENGTH OF MATERIALS AASTU

Ans: a)141.5MPa, b)166.7MPa, c)83.3MPa


6. The maximum safe compressive stress in a hardened steel punch is limited to 1000MPa, and
the punch is used to pierce circular holes in mild steel plate 20mm thick. If the ultimate shearing
stress is 312.5MPa, calculate the smallest diameter of hole that can be pierced.
Ans: 25mm
7. A rectangular bar of 250mm long is 75mm wide and 25mm thick. It is loaded with an axial
tensile load of 200kN, together with a normal compressive force of 2000kN on face
75mm×250mm and a tensile force 400kN on face 25mm×250mm. Calculate the change in
length, breadth, thickness and volume. Take E = 200GPa & v=0.3
Ans: 0.15, 0.024, 0.0197mm, 60mm3
8. A piece of 180mm long by 30mm square is in compression under a load of 90kN as shown in
the figure. If the modulus of elasticity of the material is 120GPa and Poisson’s ratio is 0.25,
find the change in the length if all lateral strain is prevented by the application of uniform
lateral external pressure of suitable intensity.

Ans: 0.125mm
9. Prove that a material subjected to pure shear in two perpendicular planes has a diagonal tension
and compression of same magnitude at 45o to the planes of shear.
10. For a given materials E=1.1×105N/mm2 & G=0.43×105N/mm2. Find bulk modulus & lateral
contraction of round bar 40mm diameter & 2.5m length when stretched by 2.5mm.
ANS: K=83.33Gpa, Lateral contraction=0.011mm
11. The modulus of rigidity of a material is 0.8×105N/mm2, when 6mm×6mm bar of this material
subjected to an axial pull of 3600N. It was found that the lateral dimension of the bar is changed
to 5.9991mm×5.9991mm. Find v & E. ANS: v=0.31, E= 210Gpa.

GIRUM M. 2

You might also like