1.

How will a router that is configured with a classless routing protocol determine the
subnet mask that should be assigned to routes that are learned from neighboring
classless routers?
• The subnet mask that is included in the routing updates will be used.
• The subnet mask of the interface that receives the update will be used.
• The subnet mask that is specified in the network command will be used.
• The class of the network in the update will determine the subnet mask that is used.
2. Which two router component and operation pair are correctly described? (Choose
two.)
• DRAM – loads the bootstrap
• RAM – stores the operating system
• Flash – executes diagnostics at bootup
• NVRAM – stores the configuration file
• ROM – stores the backup configuration file
• POST – runs diagnostics on hardware modules
3. Refer to the exhibit.

What are two of the routes added to the routing table of R1? (Choose two.)
• R 172.16.1.0/24 [120/1] via 192.168.3.0, 00:00:24, Serial0/0/0
• R 192.168.1.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/1
• R 192.168.9.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0
• R 192.168.100.0/24 [120/1] via 172.16.1.1, 00:00:24, Serial0/0/0
• R 192.168.2.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0
4. Refer to the exhibit.
 Two routers that are configured for area 0 are unable to establish neighbor adjacency.
Which two configuration changes should be made to resolve this problem? (Choose
two.)
• Both the routers should be configured for the same router ID.
• The serial interface of both the routers must be configured in the same subnet.
• Both the routers should be configured as designated routers.
• Both the routers should be configured for the same process ID.
• The network 10.1.1.0 0.0.0.3 area 0 command must be issued on both routers.
5. Which feature of a classful IP routing protocol distinguishes it from a classless IP
routing protocol?
• cannot summarize IP addresses
• allows for discontiguous IP address assignment
• supports the use of variable length subnet masks
• does not include the subnet mask in routing updates
6. When would the network administrator use the ip bandwidth-percent eigrp as-number
percent command?
• when there is a low bandwidth connection
• when the connection is on a shared medium
• when the connection is serial instead of Ethernet
• when the link is always busy
7. Refer to the exhibit.

A ping from R1 to 10.1.1.2 is successful, but a ping from R1 to 192.168.2.0 fails. What is
the cause of this problem?
• There is no gateway of last resort at R1.
• The serial interface between the two routers is down.
• A default route is not configured on R1.
• The static route for 192.168.2.0 is incorrectly configured.
8. Refer to the exhibit.

Routers R1 and R3 use different routing protocols with default administrative distance
values. All devices are properly configured and the destination network is advertised
by both protocols. Which path will be used to transmit the data packets from PC1 to
PC2?
• The packets will travel via R2-R1.
 • The packets will travel via R2-R3.
• The traffic will be load-balanced between two paths — via R2-R1 and via R2-R3.
• The packets will travel via R2-R3, and the other path via R2-R1 will be retained as
the backup path.
9. Refer to the exhibit.

A packet enters Router1 with a destination IP of 172.16.28.121. Which routing table

entry will be used to forward this packet to the destination address?
• 172.16.0.0/16 [1/0] via 192.168.0.1
• 172.16.0.0/20 [1/0] via 192.168.0.9
• 172.16.16.0/20 [1/0] via 192.168.0.17
• 0.0.0.0/0 is directly connected, Serial0/0/1
10.A network administrator is setting up a new router with a device name of Admin, an
encrypted password of cangetin, and the IP address 192.168.1.22/29 assigned to the
first FastEthernet interface. Which command sequence correctly configures this
router?
• Router(config)# hostname Admin
• Admin(config)# enable secret cangetin
• Admin(config)# interface fa0/1
• Admin(config-if)#ip address 192.168.1.22 255.255.255.248
• Router(config)# hostname Admin
• Admin(config)# enable password cangetin
• Admin(config)# interface fa0/1
• Admin(config-if)# ip address 192.168.1.22 255.255.255.248
• Router(config)# hostname Admin
• Admin(config)# enable secret cangetin
• Admin(config)# interface fa0/0
• Admin(config-if)# ip address 192.168.1.22 255.255.255.248
• Router(config)# hostname Admin
• Admin(config)# enable password cangetin
• Admin(config)# interface fa0/0
• Admin(config-if)# ip address 192.168.1.22 255.255.255.248
11.Refer to the exhibit.
 Which summarization should R1 use to advertise its networks to R2?
• 192.168.1.0/24
• 192.168.0.0/24
• 192.168.0.0/22
• 192.168.1.0/22
12.In which situation would a default static route be recommended?
• when connecting an edge router to the Internet
• when variable length subnet masking is in effect
• when there is more than one valid route for a destination network
• when a destination network has a larger mask than any routes in the routing table
13.Refer to the exhibit.

If the router loopback interfaces, FastEthernet interfaces, and OSPF priorities are
configured as shown, which router would win an OSPF DR election?
• A
• B
• C
• D
14.All routers in a network are configured in a single OSPF area with the same priority
value. No loopback interface has been set on any of the routers. Which secondary value
will the routers use to determine the router ID?
• The highest MAC address among the active interfaces of the network will be used.
• There will be no router ID until a loopback interface is configured.
• The highest IP address among the active FastEthernet interfaces that are running
OSPF will be used.
• The highest IP address among the active interfaces will be used.
15.Refer to the exhibit.
 A device is required to complete the connection between router R1 and the WAN.
Which two devices can be used for this? (Choose two.)
• a CSU/DSU device
• a modem
• an Ethernet switch
• a hub
• a bridge
16.Refer to the exhibit.

When troubleshooting a network, it is important to interpret the output of various

router commands. On the basis of the exhibit, which three statements are true?
(Choose three.)
• The missing information for Blank 1 is the command show ip route.
• The missing information for Blank 1 is the command debug ip route.
• The missing information for Blank 2 is the number 100.
• The missing information for Blank 2 is the number 120.
• The missing information for Blank 3 is the letter R.
• The missing information for Blank 3 is the letter C.
17.Refer to the exhibit.

The hosts that are connected to R2 are unable to ping the hosts that are connected to
R1. How can this problem be resolved?
• Configure the router ID on both routers.
 • Configure the R2 router interfaces for area 0.
• Configure a loopback interface on both routers.
• Configure the proper subnet masks on the router interfaces.
18.Refer to the exhibit.

All interfaces are addressed and functioning correctly. The network administrator runs
the tracert command on host A. Which two facts could be responsible for the output of
this command? (Choose two.)
• The gateway for Host A is missing or improperly configured.
• The gateway for Host B is missing or improperly configured.
• The entry for 192.168.1.0/24 is missing from the routing table of R1.
• The entry for 192.168.1.0/24 is missing from the routing table of R2.
• The entry for 192.168.2.0/24 is missing from the routing table of R1.
• The entry for 192.168.2.0/24 is missing from the routing table of R2.
19.Refer to the exhibit.

PC1 is unable to access the Internet. What is the cause of the problem?
• An incorrect IP address is configured between the two routers.
• No static route is configured on Router2.
• A routing loop has occurred.
• No routing protocol is configured on either of the two routers.
20.Refer to the exhibit.

Routers R1 and R2 are directly connected via their serial interfaces and are both
 running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial
interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
• What action should be taken to solve this problem?
• Enable the serial interfaces of both routers.
• Configure EIGRP to send periodic updates.
• Configure the same hello interval between the routers.
• Configure both routers with the same EIGRP process ID.
21.Refer to the exhibit.

The routers in the exhibit are running the EIGRP routing protocol. What statement is
true regarding how packets will travel from the 172.16.1.0/16 network to the
192.168.200.0/24 network?
• The router chooses the first path that it learned and installs only that route in the
routing table.
• The router chooses the path with the lowest administrative distance and installs only
that route in the routing table.
• The router chooses the highest routing ID based on the advertised network IP
addresses and installs only that route in the routing table.
• The router installs all the equal cost paths in the routing table but sends packets out
only one, holding the others in reserve in case the primary route goes down.
• The router installs all the equal cost paths in the routing table and performs equal
cost load balancing to send packets out multiple exit interfaces.
22.Refer to the exhibit.

Routers 1 and 2 are directly connected over a serial link. Pings are failing between the
two routers. What change by the administrator will correct the problem?
• Set the encapsulation on both routers to PPP.
• Decrease the bandwidth on Serial 0/1/0 on router 2 to 1544.
• Change the cable that connects the routers to a crossover cable.
• Change the IP address on Serial 0/1/0 on router 2 to 192.168.0.1/30.
23.You have been asked to explain converged networks to a trainee. How would you
accurately describe a converged network?
• A network is converged when all routers have formed an adjacency.
• A network is converged immediately after a topology change has occurred.
• A network is converged when all routers flush the unreachable networks from their
routing tables.
• A network is converged after all routers share the same information, calculate best
paths, and update their routing tables.
24.Which port should a terminal emulator be connected to in order to access a router
 without network connectivity?
• T1
• serial
• console
• FastEthernet
25.Which component is typically used to connect the WIC interface of a router to a
CSU/DSU?
• V.35 cable
• RJ-45 adapter
• crossover cable
• straight-through cable
26.Refer to the exhibit.

Which route will be removed from the routing table if manual EIGRP summarization
is disabled the Serial0/0/0 interface of R3?
• 0.0.0.0/0
• 172.16.0.0/16
• 172.16.1.0/24
• 172.16.3.0/30
27.A router has learned two equal cost paths to a remote network via the EIGRP and RIP
protocols. Both protocols are using their default configurations. Which path to the
remote network will be installed in the routing table?
• the path learned via EIGRP
• the path learned via RIP
• the path with the highest metric value
• both paths with load balancing
28.Using default settings, what is the next step in the router boot sequence after the IOS
loads from flash?
• Perform the POST routine.
• Search for a backup IOS in ROM.
• Load the bootstrap program from ROM.
• Load the running-config file from RAM.
• Locate and load the startup-config file from NVRAM.
29.Refer to the exhibit.
 Which two statements are true based on the exhibited output? (Choose two.)
• All routes are stable.
• Each route has one feasible successor.
• The serial interface between the two routers is down.
• The administrative distance of EIGRP has been set to 50.
• The show ip eigrp topology command has been run on R1.
30.Refer to the exhibit.

The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two
results of this command? (Choose two.)
• A static route will be updated in the routing table.
• The traffic from the Internet will be directed to R2.
• The traffic from the source network 172.16.0.0/22 will be blocked.
• The route will be specified as the default route for all networks not defined in the
routing table.
• All the broadcasts will be forwarded via the S0/0/0 interface of R2.
31.Which two statements are true about the EIGRP successor route? (Choose two.)
• It is saved in the topology table for use if the primary route fails.
• It may be backed up by a feasible successor route.
• It is used by EIGRP to forward traffic to the destination.
• It is flagged as active in the routing table.
• After the discovery process has occurred, the successor route is stored in the
neighbor table.
32.Which mechanism helps to avoid routing loops by advertising a metric of infinity?
• route poisoning
• split horizon
• hold-down timer
• triggered updates
33.Refer to the exhibit.
 Which two facts can be derived from this output? (Choose two.)
• Three network devices are directly connected to Router2.
• The serial interface between Router2 and Router3 is up.
• Router1 and Router3 are directly connected.
• Six devices are up and running on the network.
• Layer 3 functionality between routers is configured properly.
34.Refer to the exhibit.

A static route was configured on router R1 to forward packets to the remote networks.
During a network upgrade, the network administrator configured RIPv2 on all routers
in the network. What will router R1 do with a packet that is sourced from PC1 and
destined for PC3?
• The packet will be forwarded out the Serial0/0/0 interface via the static route.
• The packet will be forwarded out the FastEthernet0/1 interface via the static route.
• The packet will be forwarded out the Serial0/0/0 interface via the route that is
learned through RIP.
• The packet will be forwarded out the FastEthernet0/1 interface via the route that is
learned through RIP.
35.Which statement is true regarding routing metrics?
• All routing protocols use the same metrics.
 • EIGRP uses bandwidth as its only metric.
• Routers compare metrics to determine the best route.
• The larger metric generally represents the better path.
36.Refer to the exhibit.

The results of the show ip route command are displayed in the graphic for Router R2.
Which route will be selected for a packet with a destination address of 10.1.4.1?
• route to 0.0.0.0/0
• route to 10.1.0.0/22
• route to 10.1.0.0/23
• route to 10.1.0.0/24
37.Refer to the exhibit.

A network administrator is trying to determine why router JAX has no OSPF routes in
its routing table. All routers are configured for OSPF area 0. From the JAX router, the
administrator is able to ping its connected interfaces and the Fa0/1 interface of the
ORL router but no other router interfaces. What is a logical step that the network
administrator should take to troubleshoot the problem?
• Reboot the routers.
• Change the OSPF process ID on all of the routers to 0.
• Check to see if the cable is loose between ORL and JAX.
• Check to see if CDP packets are passing between the routers.
• Use show and debug commands to determine if hellos are propagating.
38.Refer to the exhibit.
 R1 and R2 are both configured with RIPv1. Beginning from global configuration
mode, what comand or commands will eliminate RIP updates on the Ethernet segment
of R2?
• R2# configure terminal
• R2(config)# router rip
• R2(config-router)# passive-interface FastEthernet0/0
• R2# configure terminal
• R2(config)# passive-interface FastEthernet0/0
• R2# passive-interface FastEthernet0/0
• R2# configure terminal
• R2(config)# interface FastEthernet0/0
• R2(config-if)# passive-interface FastEthernet0/0
39.Refer to the exhibit.

Although R2 is configured correctly, host A is unable to access the Internet. What are
two static routes that can be configured on R1, either of which would enable Internet
connectivity for host A? (Choose two.)
• ip route 0.0.0.0 0.0.0.0 Fa0/0
• ip route 0.0.0.0 0.0.0.0 Fa0/1
• ip route 0.0.0.0 0.0.0.0 10.1.1.1
• ip route 0.0.0.0 0.0.0.0 10.1.1.2
• ip route 209.165.202.0 255.255.255.0 10.1.1.1
40.Refer to the exhibit.
 How many routes are both level 1 and qualify for use as an ultimate route?
• 1
• 2
• 3
• 4
• 5
• 6
41.A network administrator is in charge of two separate networks that share a single
building. What device will be required to connect the two networks and add a common
connection to the Internet that can be shared?
• hub
• router
• access point
• Ethernet switch
42.In a lab test environment, a router has learned about network 172.16.1.0 through four
different dynamic routing processes. Which route will be used to reach this network?
• D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0
• O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0
• R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0
• I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0
43.Refer to the exhibit.

A network administrator is troubleshooting the OSPF network. The 10.10.0.0/16

 network is not showing up in the routing table of Router1. What is the probable cause
of this problem?
• The serial interface on Router2 is down.
• The OSPF process is not running on Router2.
• The OSPF process is configured incorrectly on Router1.
• There is an incorrect wildcard mask statement for network 10.10.0.0/16 on Router2.
44.Refer to the exhibit.

A technician has configured the interfaces on the Router, but upon inspection discovers
that interface FastEthernet0/1 is not functioning. Which action will most likely correct
the problem with FastEthernet0/1?
• A clock rate should be added to the interface configuration.
• The subnet mask should be added to the interface configuration.
• An interface description needs to be added to the interface configuration.
• The no shutdown command needs to be added to the interface configuration.
45.Which subnetting scheme will accommodate a network of 10 LANs, each of which
contains a minimum of 2000 hosts?
• 10.0.0.0/10
• 10.0.0.0/11
• 172.16.0.0/18
• 172.16.0.0/20
46.Refer to the exhibit.

What does the highlighted entry for network 172.30.0.0/16 indicate?

• Automatic summarization is enabled on R1.
• The routing table of R2 contains only classful networks.
• R2 will reject this update.
• The routing protocol that is configured on both routers is RIPv1.
47.Which three statements about routing protocols are true? (Choose three.)
• EIGRP supports unequal cost load balancing.
• RIP cannot be configured to allow classless routing.
• OSPF elects designated routers on multiaccess links.
• RIP does not advertise a route beyond a hop count of 15.
• EIGRP uses broadcast traffic to establish adjacencies with its neighbors.
• OSPF can convergence more quickly because it can find a feasible successor in its
topology table when a successor route goes down.
48.Which statement correctly describes a feasible successor in EIGRP?
• It is a primary route that is stored in the routing table.
• It is a backup route that is stored in the routing table.
• It is a primary route that is stored in the topology table.
 • It is a backup route that is stored in the topology table.
49.Refer to the exhibit.

Which host has a combination of IP address and subnet mask on the same network as
Fa0/0 of Router1?
• host A
• host B
• host C
• host D
50.Which statement correctly describes a feature of RIP?
• RIP is a link-state routing protocol.
• RIP uses only one metric—hop count— for path selection.
• Advertised routes with hop counts greater than 10 are unreachable.
• Messages are broadcast every 10 seconds.
51.Refer to the exhibit.

All routers are properly configured with default configurations and are running the
OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24
network is communicating with a host on the 192.168.2.0/24 network. Which path will
be used to transmit the data?
• The data will be transmitted via R3-R2.
• The data will be transmitted via R3-R1-R2.
• The traffic will be load-balanced between two paths — one via R3-R2, and the other
via R3-R1-R2.
• The data will be transmitted via R3-R2, and the other path via R3-R1-R2 will be
retained as the backup path.
52.What is the function of the OSPF LSU packet?
• used to confirm receipt of certain types of OSPF packets
• used to establish and maintain adjacency with other OSPF routers
• used to request more information about any entry in the BDR
• used to announce new OSPF information and to reply to certain types of requests