Scribd
Upload
95 views

HA Next Generation: Operator Display'

This document provides information about the operator display of an HA next Generation machine. It describes what is shown on the display when the machine is powered down, powered up, in idle state, and during a dispense job. It also describes the functions of the buttons and lights shown, including lights that indicate when a can is needed, the dispense job progress, machine panels are opened, the emergency switch is activated, or canisters need refilling. Error messages and symbols for brush cleaning are also summarized.

Uploaded by

Ray Putra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
95 views

HA Next Generation: Operator Display'

This document provides information about the operator display of an HA next Generation machine. It describes what is shown on the display when the machine is powered down, powered up, in idle state, and during a dispense job. It also describes the functions of the buttons and lights shown, including lights that indicate when a can is needed, the dispense job progress, machine panels are opened, the emergency switch is activated, or canisters need refilling. Error messages and symbols for brush cleaning are also summarized.

Uploaded by

Ray Putra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

HA next Generation

‘Operator Display’
Machine powered down

This is how
the operator
display looks
when the
machine is
powered
down.

PC on/off
swtich Function key
Machine powered up
This is how the
operator display
looks when the
machine is being
powered up or
after releasing
the emergency
switch

The progress bar


presents a
walking light from
top to botom and
back
Machine in idle state

Not initialized Asleep but stand by. Ready, awake NO can Ready and can present
Buttons

This button operates the PC-wall The function button has two
socket in the machine. functionalities:
 A short touch shows the
Switching the PC on and off firmware version that is
 Push and hold the button loaded onto the board
 Progress bar slowly fills up  A prolonged touch (push
from bottom to top with and hold) starts a
bars that light up. machine initialization
 Switching takes place when  Progress bar slowly fills
progress bar is completely up from bottom to top.
filled. Initialization starts
 A beep sounds for afterwards.
confirmation.  When the table turns
 PC switch light goes during initialization, the
on/off. pumpcount is shown
 While touching the button during the second round.
the light blinks.
Place a can

When the machine waits


for a can after having
received a dispense job
from the software, this
light will blink.
Dispense Job Progress

The progress bar visualizes how much time


is left before the dispense job is finished.

At the start of a dispense job,


a timer will display the
estimated time in seconds, As soon as the valve of the last pump is
needed to complete the job. closed, this light will turn to green,
During dispensing it will count meaning that the can can be removed.
After removal, the light goes off.
down to 0.
Machine opened

Top lid opened

Front door opened

If one of the machine panels is opened,


a warning will be given by displaying the Switchplate pressed or
accompanying light symbol. The absent
displayed light will be a static one,
without signalling an error message.
Brush cup misplaced
or absent.
Emergency switch activated

If the emergency switch is pressed,


its accompanying light will blink and
an error code will be displayed
Canister refilling

If a canister needs to be refilled,


this symbol will light. (Also
indicated in the IDD under warning
level)
Brush cleaning
This symbol blinks if
Based on the brush switch signal, it the brush needs to be
can be calculated when the brush cleaned.
was taken out of the machine for the
last time.

The brush symbol will blink when:


• > 14 days (=336hrs) no
cleaning
• > 100 recipes ago since the
last cleaning.

When the brush has been taken out


of the machine longer than 60 sec,
it is assumed cleaned.

The above mentioned numbers will


be changeable in the
driversoftware.
Errormessages

If any technical failure occurs,


that machine can’t deal with
itself, an error code will be
displayed (E+ 2 digits).
Not is use/for future use…

You might also like