12-2018

Process
Construction HSE Management
QM code
thyssenkrupp PIN LP-CHM-022 F01
JOB SAFETY ANALYSIS
Industrial Solutions (India)

Job area is considered: Establishment/Project: JSA No.:

Project No: 66-6695 1.0MTPA Alumina Refinery

Contractor: tkIS India: Client:

Person participating in 1. 1 1.
Job Safety Analysis. 2. 2. 2.
3.

JOB DESCRIPTION: Height work

Requirement of adding Personal Protection Requirement of adding special equipment or tool

Requirement of Working Permit Equipment.
(Check the relevant box) (Additional list)
Restricted space 1. Helmet 6.Goggles 1.Hammer
Heating job 2. Shoe 7. Cotton hand gloves 2.Lifting Rope
Digging 3.Full body harness 3. Spanner
Isolation / Energization 4. Lifeline
Other job  5. Ladder/Scaffold

JSA considering procedure Yes No Comment

Is JSA establishment participated by job implementing group? 

tkIS India Form: Job Safety Analysis

12-2018
 12-2018
Process
Construction HSE Management
QM code
thyssenkrupp PIN LP-CHM-022 F01
JOB SAFETY ANALYSIS
Industrial Solutions (India)

Is JSA considered by Job implementing group before carrying out the job? 

Is JSA sheet used/ consulted in work implementation? 

Is the job carried out step by step? 

Do you propose to improve JSA sheet (give in detail) 


Is detail of any trouble showing

ACTIVITIES HAZARD/ DANGER CONTROL MEASURE ACTION

Separate the job into the Describe all hazards identified for Describe fully all equipment, facility, and/or procedure controls applicable for each
main tasks and record each task based on observations hazard.
them in sequence. and experience.
Height work  Fall of person from  Obtain height work permit from concern department prior to commence the
height height work 1.5mtrs and above.
 Material fall from  Only trained & vertigo qualified person do the height work.
height  Use scaffold or proper elevated working platform for height work
 Collapse of structure  Provide guard rails at the work place.
 Slip and trip hazard  Use PPE like full body harness, life line, approach, helmets, safety shoes, etc.
 Electrocution hazard  Fall arrest and safety nets etc., to be installed (If necessary).
 Weather effect  Provide adequate working space in working platform (min.0.6m).
 Working platform must be rigid.
 Use ladder as per standard. (1:4 ratio or 70 degrees angle).

tkIS India Form: Job Safety Analysis

12-2018
 12-2018
Process
Construction HSE Management
QM code
thyssenkrupp PIN LP-CHM-022 F01
JOB SAFETY ANALYSIS
Industrial Solutions (India)

 Don’t paint to the ladder.

 Ladder should place in secure place, not keep in front of door or slanting area.
 Don’t allow to carry material along with person while ascending and
descending in ladder.
 While ascending and descending 3-point contact should maintain.
 Keep barricade the work area and restrict unauthorized entry.
 Keep the work place neat and clean.
 Do not throw or drop materials or equipment from height.
 Use rope and pulley to lift up and take down the material.
 All tools to be carried in a tool- kit Bag or on working uniform (As convenient).
 Remove scrap from the planks / platform immediately after finishing work.
 Ensure wearing of helmet by the workers working at lower levels.
 No live electrical line should attach with working platform/scaffold.
 Scaffold/elevated working platform circumstance should be clear from any
other obstruction.
 Don’t allow to do work at height when dusty and heavy wind flow.
 Weld, bend, modified and rust pipe should not use to erect scaffold.
 All workmen should skilled and trained to work.
 Conduct training prior to start the job.
 Proper supervision should provide to the job.
 At a time, multiple activities are not allowed in up & down at the same work
place.

tkIS India Form: Job Safety Analysis

12-2018
 12-2018
Process
Construction HSE Management
QM code
thyssenkrupp PIN LP-CHM-022 F01
JOB SAFETY ANALYSIS
Industrial Solutions (India)

Prepared by Reviewed by Approved by

(Contractor ) (tkIS) (NALCO)
Name: Name: Name:

Designation: Designation: Designation:

Signature: Signature: Signature:
Date: Date: Date:

tkIS India Form: Job Safety Analysis

12-2018