Distortion - Australian Welding Institute https://welding.org.

au/welding/distortion/

U a


DISTORTION
Jan 1, 2017 | Job Knowledge, Welding | 1 comment

DISTORTION – TYPES AND CAUSES

This article covers several key issues on distortion in arc welded
fabrications, especially basic types of and factors affecting the degree of
distortion.

What causes distortion?

1 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Because welding involves highly localised heating of joint edges to fuse the
material, non-uniform stresses are set up in the component because of
expansion and contraction of the heated material. Initially, compressive

stresses are created in the surrounding cold parent metal when the weld
pool is formed due to the thermal expansion of the hot metal (heat
affected zone) adjacent to the weld pool. However, tensile stresses occur
on cooling when the contraction of the weld metal and the immediate heat
affected zone is resisted by the bulk of the cold parent metal.

The magnitude of thermal stresses induced into the material can be seen
by the volume change in the weld area on solidification and subsequent
cooling to room temperature. For example, when welding C-Mn steel, the
molten weld metal volume will be reduced by approximately 3% on
solidification and the volume of the solidified weld metal/heat affected
zone (HAZ) will be reduced by a further 7% as its temperature falls from the
melting point of steel to room temperature.

If the stresses generated from thermal expansion/contraction exceed the

yield strength of the parent metal, localised plastic deformation of the
metal occurs. Plastic deformation causes a permanent reduction in the
component dimensions and distorts the structure.

What are the main types of distortion?

Distortion occurs in six main forms:

• Longitudinal shrinkage
• Transverse shrinkage
• Angular distortion
• Bowing and dishing
• Buckling
• Twisting

The principal features of the more common forms of distortion for butt and

2 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

fillet welds are shown below:

Contraction of the weld area on cooling results in both transverse and

longitudinal shrinkage.

Non-uniform contraction (through thickness) produces angular distortion in

addition to longitudinal and transverse shrinkage.

For example, in a single V butt weld, the first weld run produces
longitudinal and transverse shrinkage and rotation. The second run causes
the plates to rotate using the first weld deposit as a fulcrum. Hence,
balanced welding in a double side V butt joint can be used to produce
uniform contraction and prevent angular distortion.

Similarly, in a single side fillet weld, non-uniform contraction produces

angular distortion of the upstanding leg. Double side fillet welds can
therefore be used to control distortion in the upstanding fillet but because
the weld is only deposited on one side of the base plate, angular distortion
will now be produced in the plate.

Longitudinal bowing in welded plates happens when the weld centre is not
coincident with the neutral axis of the section so that longitudinal shrinkage
in the welds bends the section into a curved shape. Clad plate tends to bow
in two directions due to longitudinal and transverse shrinkage of the
cladding; this produces a dished shape. Dishing is also produced in stiffened
plating. Plates usually dish inwards between the stiffeners, because of

3 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

angular distortion at the stiffener attachment welds (see main photograph).

In plating, long range compressive stresses can cause elastic buckling in thin
plates, resulting in dishing, bowing or rippling. 
Distortion due to elastic buckling is unstable: if you attempt to flatten a
buckled plate, it will probably ‘snap’ through and dish out in the opposite
direction.

Twisting in a box section is caused by shear deformation at the corner

joints. This is caused by unequal longitudinal thermal expansion of the
abutting edges. Increasing the number of tack welds to prevent shear
deformation often reduces the amount of twisting.

How much shall I allow for weld shrinkage?

It is almost impossible to predict accurately the amount of shrinking.

Nevertheless, a ‘rule of thumb’ has been composed based on the size of the
weld deposit. When welding steel, the following allowances should be
made to cover shrinkage at the assembly stage.

TRANSVERSE SHRINKAGE
Fillet Welds 0.8mm per weld where the leg length does not exceed 3/4
plate thickness

Butt weld 1.5 to 3mm per weld for 60° V joint, depending on number of
runs

Longitudinal shrinkage

Fillet Welds 0.8mm per 3m of weld

Butt Welds 3mm per 3m of weld

4 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Increasing the leg length of fillet welds, in particular, increases shrinkage.

What are the factors affecting distortion?


If a metal is uniformly heated and cooled there would be almost no
distortion. However, because the material is locally heated and restrained
by the surrounding cold metal, stresses are generated higher than the
material yield stress causing permanent distortion. The principal factors
affecting the type and degree of distortion, are:

• Parent material properties

• Amount of restraint
• Joint design
• Part fit-up
• Welding procedure
• Parent material properties

Parent material properties which influence distortion are coefficient of

thermal expansion and specific heat per unit volume.

As distortion is determined by expansion and contraction of the material,

the coefficient of thermal expansion of the material plays a significant role
in determining the stresses generated during welding and, hence, the
degree of distortion. For example, as stainless steel has a higher coefficient
of expansion than plain carbon steel, it is more likely to suffer from
distortion.

RESTRAINT
If a component is welded without any external restraint, it distorts to relieve
the welding stresses. So, methods of restraint, such as ‘strong-backs’ in butt
welds, can prevent movement and reduce distortion. As restraint produces
higher levels of residual stress in the material, there is a greater risk of
cracking in weld metal and HAZ especially in crack-sensitive materials.

5 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

JOINT DESIGN
Both butt and fillet joints are prone to distortion. It can be minimised in
butt joints by adopting a joint type which balances the thermal stresses 
through the plate thickness. For example, a double-sided in preference to a
single-sided weld. Double-sided fillet welds should eliminate angular
distortion of the upstanding member, especially if the two welds are
deposited at the same time.

PART FIT-UP
Fit-up should be uniform to produce predictable and consistent shrinkage.
Excessive joint gap can also increase the degree of distortion by increasing
the amount of weld metal needed to fill the joint. The joints should be
adequately tacked to prevent relative movement between the parts during
welding.

WELDING PROCEDURE
This influences the degree of distortion mainly through its effect on the
heat input. As welding procedure is usually selected for reasons of quality
and productivity, the welder has limited scope for reducing distortion. As a
general rule, weld volume should be kept to a minimum. Also, the welding
sequence and technique should aim to balance the thermally induced
stresses around the neutral axis of the component.

DISTORTION – PREVENTION BY
DESIGN

6 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Photo of strongbacks on girder flange to

prevent cross bowing. Courtesy John Allen

General guidelines are given below as ‘best practice’ for limiting distortion
when considering the design of arc welded structures.

DESIGN PRINCIPLES
At the design stage, welding distortion can often be prevented, or at least
restricted, by considering:

• elimination of welding
• weld placement
• reducing the volume of weld metal
• reducing the number of runs
• use of balanced welding

ELIMINATION OF WELDING
As distortion and shrinkage are an inevitable result of welding, good design
requires that not only the amount of welding is kept to a minimum, but also
the smallest amount of weld metal is deposited. Welding can often be
eliminated at the design stage by forming the plate or using a standard
rolled section, as shown in Fig 1.

7 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Fig. 1 Elimination of welds by:

a) Forming the plate;



b) Use of rolled or extruded section

If possible, the design should use intermittent welds rather than a

continuous run, to reduce the amount of welding. For example, in attaching
stiffening plates, a substantial reduction in the amount of welding can often
be achieved whilst maintaining adequate strength.

WELD PLACEMENT
Placing and balancing of welds are important in designing for minimum
distortion. The closer a weld is positioned to the neutral axis of a
fabrication, the lower the leverage effect of the shrinkage forces and the
final distortion.

Examples of poor and good designs are shown in Fig 2.

Fig. 2 Distortion may be reduced by placing

the welds around the neutral axis

As most welds are deposited away from the neutral axis, distortion can be
minimised by designing the fabrication so the shrinkage forces of an
individual weld are balanced by placing another weld on the opposite side
of the neutral axis.

8 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Whenever possible, welding should be carried out alternately on opposite

sides, instead of completing one side first. In large structures, if distortion is
occurring preferentially on one side, it may be possible to take corrective

actions, for example, by increasing welding on the other side to control the
overall distortion.

REDUCING THE VOLUME OF WELD

METAL
To minimise distortion, as well as for economic reasons, the volume of weld
metal should be limited to the design requirements.

For a single-sided joint, the cross-section of the weld should be kept as

small as possible to reduce the level of angular distortion, as illustrated in
Fig 3.

Fig. 3 Reducing the amount of angular distortion and lateral shrinkage by:

a) reducing the volume of weld metal;

b) using single pass weld

Joint preparation angle and root gap should be minimised providing the
weld can be made satisfactorily.

To facilitate access, it may be possible to specify a larger root gap and

smaller preparation angle. By cutting down the difference in the amount of

9 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

weld metal at the root and the face of the weld, the degree of angular
distortion will be correspondingly reduced. Butt joints made in a single pass
using deep penetration have little angular distortion, especially if a closed

butt joint can be welded (Fig 3).

For example, thin section material can be welded using plasma and laser
welding processes and thick section can be welded, in the vertical position,
using electrogas and electroslag processes.

Although angular distortion can be eliminated, there will still be longitudinal

and transverse shrinkage.

In thick section material, as the cross sectional area of a double-V joint

preparation is often only half that of a single-V preparation, the volume of
weld metal to be deposited can be substantially reduced. The double-V
joint preparation also permits balanced welding about the middle of the
joint to eliminate angular distortion.

As weld shrinkage is proportional to the amount of weld metal, both poor

joint fit-up and over-welding will increase the amount of distortion. Angular
distortion in fillet welds is particularly affected by over-welding. As design
strength is based on throat thickness, over-welding to produce a convex
weld bead does not increase the allowable design strength but it will
increase the shrinkage and distortion.

REDUCING THE NUMBER OF RUNS

There are conflicting opinions on whether it is better to deposit a given
volume of weld metal using a small number of large weld passes or a large
number of small passes.

10 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Experience shows that for a single-sided butt joint, or a single-side fillet

weld, a large single weld deposit gives less angular distortion than if the
weld is made with a number of small runs.

Generally, in an unrestrained joint, the degree of angular distortion is
approximately proportional to the number of passes.

Completing the joint with a small number of large weld deposits results in
more longitudinal and transverse shrinkage than a weld completed in a
larger number of small passes. In a multi-pass weld, previously deposited
weld metal provides restraint, so the angular distortion per pass decreases
as the weld is built up. Large deposits also increase the risk of elastic
buckling particularly in thin section plate.

USE OF BALANCED WELDING

Balanced welding is an effective means of controlling angular distortion in a
multi-pass butt weld by arranging the welding sequence to ensure that
angular distortion is continually being corrected and not allowed to
accumulate during welding.

Comparative amounts of angular distortion from balanced welding and

welding one side of the joint first are shown schematically in Fig 4. The
balanced welding technique can also be applied to fillet joints.

11 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Fig. 4 Balanced welding to reduce the amount

of angular distortion

If welding alternately on either side of the joint is not possible, or if one side 
has to be completed first, an asymmetrical joint preparation may be used
with more weld metal being deposited on the second side.

The greater contraction resulting from depositing the weld metal on the
second side will help counteract the distortion on the first side.

BEST PRACTICE
The following design principles can control distortion:

• eliminate welding by forming the plate and using rolled or extruded

sections
• minimise the amount of weld metal
• do not over weld
• use intermittent welding in preference to a continuous weld pass
• place welds about the neutral axis
• balance the welding about the middle of the joint by using a double-V
joint in preference to a single-V joint

Adopting best practice principles can have surprising cost benefits. For
example, for a design fillet leg length of 6mm, depositing an 8mm leg
length will result in the deposition of 57% additional weld metal.

Besides the extra cost of depositing weld metal and the increase risk of
distortion, it is costly to remove this extra weld metal later.

However, designing for distortion control may incur additional fabrication

costs. For example, the use of a double-V joint preparation is an excellent
way to reduce weld volume and control distortion, but extra costs may be
incurred in production through manipulation of the workpiece for the
welder to access the reverse side.

12 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

DISTORTION CONTROL – PREVENTION

BY FABRICATION TECHNIQUES


Distortion caused by welding

a plate at the centre of a thin

plate before welding into a

bridge girder section.

Courtesy John Allen

ASSEMBLY TECHNIQUES
In general, the welder has little influence on the choice of welding
procedure but assembly techniques can often be crucial in minimising
distortion. The principal assembly techniques are:

• tack welding
• back-to-back assembly
• stiffening

TACK WELDING
Tack welds are ideal for setting and maintaining the joint gap but can also
be used to resist transverse shrinkage. To be effective, thought should be
given to the number of tack welds, their length and the distance between
them. With too few, there is the risk of the joint progressively closing up as
welding proceeds. In a long seam, using MMA or MIG, the joint edges may
even overlap. It should be noted that when using the submerged arc

13 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

process, the joint might open up if not adequately tacked.

The tack welding sequence is important to maintain a uniform root gap

along the length of the joint. Three alternative tack welding sequences are 
shown in Fig. 1:

a) tack weld straight through to the end of the joint (Fig 1a). It is necessary
to clamp the plates or to use wedges to maintain the joint gap during
tacking

b) tack weld one end and then use a back stepping technique for tacking
the rest of the joint (Fig 1b)

c) tack weld the centre and complete the tack welding by back stepping (Fig
1c).

Fig. 1. Alternative procedures used for

tack welding to prevent transverse

shrinkage

a) tack weld straight through to end of joint

b) tack weld one end, then use back-step technique for tacking the rest of
the joint
c) tack weld the centre, then complete the tack welding by the back-step
technique

Directional tacking is a useful technique for controlling the joint gap, for

14 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

example closing a joint gap which is (or has become) too wide.

When tack welding, it is important that tacks which are to be fused into the
main weld are produced to an approved procedure using appropriately 
qualified welders. The procedure may require preheat and an approved
consumable as specified for the main weld. Removal of the tacks also
needs careful control to avoid causing defects in the component surface.

BACK-TO-BACK ASSEMBLY
By tack welding or clamping two identical components back-to-back,
welding of both components can be balanced around the neutral axis of
the combined assembly (Fig. 2a). It is recommended that the assembly is
stress relieved before separating the components. If stress relieving is not
done, it may be necessary to insert wedges between the components (Fig.
2b) so when the wedges are removed, the parts will move back to the
correct shape or alignment.

Fig. 2. Back-to-back assembly to control

distortion when welding two identical

components

a) assemblies tacked together before welding

b) use of wedges for components that distort on separation after welding

STIFFENING

15 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

Fig. 3. Longitudinal stiffeners prevent bowing in butt

welded thin plate joints

Longitudinal shrinkage in butt welded seams often results in bowing,

especially when fabricating thin plate structures. Longitudinal stiffeners in
the form of flats or angles, welded along each side of the seam (Fig. 3) are
effective in preventing longitudinal bowing. Stiffener location is important:
they must be placed at a sufficient distance from the joint so they do not
interfere with welding, unless located on the reverse side of a joint welded
from one side.

WELDING PROCEDURE
A suitable welding procedure is usually determined by productivity and
quality requirements rather than the need to control distortion.
Nevertheless, the welding process, technique and sequence do influence
the distortion level.

WELDING PROCESS
General rules for selecting a welding process to prevent angular distortion
are:

• deposit the weld metal as quickly as possible

• use the least number of runs to fill the joint

Unfortunately, selecting a suitable welding process based on these rules

16 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

may increase longitudinal shrinkage resulting in bowing and buckling.

In manual welding, MIG, a high deposition rate process, is preferred to

MMA. Weld metal should be deposited using the largest diameter electrode 
(MMA), or the highest current level (MIG), without causing lack-of-fusion
imperfections. As heating is much slower and more diffuse, gas welding
normally produces more angular distortion than the arc processes.

Mechanised techniques combining high deposition rates and high welding

speeds have the greatest potential for preventing distortion.

As the distortion is more consistent, simple techniques such as presetting

are more effective in controlling angular distortion.

WELDING TECHNIQUE
General rules for preventing distortion are:

• keep the weld (fillet) to the minimum specified size

• use balanced welding about the neutral axis
• keep the time between runs to a minimum

Fig. 4. Angular distortion of the

joint as determined by the

number of runs in the fillet weld

In the absence of restraint, angular distortion in both fillet and butt joints

17 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

will be a function of the joint geometry, weld size and the number of runs
for a given cross section. Angular distortion (measured in degrees) as a
function of the number of runs for a 10mm leg length fillet weld is shown in

Fig. 4.

If possible, balanced welding around the neutral axis should be done, for
example on double sided fillet joints, by two people welding
simultaneously. In butt joints, the run order may be crucial in that balanced
welding can be used to correct angular distortion as it develops.

Fig. 5. Use of welding direction to control distortion

a) Back-step welding

b) Skip welding

Welding sequence

The sequence, or direction, of welding is important and should be towards

the free end of the joint. For long welds, the whole of the weld is not
completed in one direction. Short runs, for example using the back-step or
skip welding technique, are very effective in distortion control (Fig. 5).

• Back-step welding involves depositing short adjacent weld lengths in

the opposite direction to the general progression (Fig. 5a).
• Skip welding is laying short weld lengths in a predetermined, evenly
spaced, sequence along the seam (Fig. 5b). Weld lengths and the
spaces between them are generally equal to the natural run-out length

18 of 25 10/1/2021, 6:32 PM
Distortion - Australian Welding Institute https://welding.org.au/welding/distortion/

of one electrode. The direction of deposit for each electrode is the

same, but it is not necessary for the welding direction to be opposite to
the direction of general progression.

BEST PRACTICE
The following fabrication techniques are used to control distortion:

• using tack welds to set up and maintain the joint gap

• identical components welded back to back so welding can be balanced
about the neutral axis
• attachment of longitudinal stiffeners to prevent longitudinal bowing in
butt welds of thin plate structures
• where there is choice of welding procedure, process and technique
should aim to deposit the weld metal as quickly as possible; MIG in
preference to MMA or gas welding and mechanised rather than manual
welding
• in long runs, the whole weld should not be completed in one direction;
back-step or skip welding techniques should be used.

These articles were prepared by Bill Lucas in collaboration with Geert

Verhaeghe, Rick Leggatt and Gene Mathers.

Copyright © TWI Ltd 2014

The content of this article was correct at the time of publication. For more
information visit www.twi-global.com

ACCOUNT

Username

19 of 25 10/1/2021, 6:32 PM