TP78xx-1 Series

DESCRIPTION： Wide Input Non-Isolated、Regulated Single Output

The TP78xx-1 series has high efficiency, short circuit protection, Thermal

shutdown, no heat sink required, Industry standard pinout.ideal for redialing 78xx

linear regulates and are pin compatible.

FEATURES
ROHS Compliant Wide input non-isolated、regulated single output Efficiency up to 93%
Short circuit protection, Thermal shutdown Temperature range: -40ºC ~ +85ºC Low ripple noise
SIP package No heat sink required Industry standard pinout

SELECTION GUIDE
Input Voltage (VDC) Output Efficiency（%）
Part Number
Nominal Range Voltage（VDC) Current（mA) Vin (Min) Vin(Max)

TP781.5-1 12 4.75~18 1.5 1000 78 72

TP781.8-1 12 4.75~18 1.8 1000 82 76

TP782.5-1 12 4.75~18 2.5 1000 87 82

TP783.3-1 12 4.75~20 3.3 1000 90 83

TP785.0-1 12 6.5~20 5.0 1000 93 85

TP783.3W-1 24 8~32 3.3 1000 87 80

TP785.0W-1 24 8~32 5.0 1000 87 80

OUTPUT CHARACTERISTICS
Parameter Conditions Min Typ. Max. Units
Output voltage accuracy 100% full load, input voltage range ±2 ±3
Line regulation Vin=min. to max, at full load ±0.5 ±0.75 %
Load regulation 10% to 100% load ±0.5 ±1.0
Ripple & Noise 20MHz bandwidth,(refer to figure 3) 25 45 mvp-p
Short circuit protection Continuous, auto-recovery
Thermal shutdown Internal IC junction 150 ℃
Output current limit 3000 mA
Switching frequency Full load, input voltage range 335 385 435 KHz
Dynamic load stability ±100 mA
Quiescent current Vin from min to max and at 0% load 7 10 mA
Temperature coefficient –40℃~+85℃ ±0.02 %/℃
Max capacitance load 1000 μF
All specifications typical at TA=25ºC, nominal input voltage and rated output current unless otherwise specified.
COMMON SPECIFICATIONS
Parameter Conditions Min. Typ. Max. Units
Storage humidity range 95
Operating temp. range Power derating (above 71ºC) -40 85
Storage temp. range -55 125 ℃
Storage temp. Range Temp rise at full load 100
Lead temperature 1.5mm from case for 10 seconds 300
Cooling Free air convection

Case material Plastic (UL94-V0)

MTBF 25℃（MIL-HDBK-217F） 2000 k hours

Weight 2.0 g

www.gztoppower.com TEL:0086-20-62162688 EMAIL:[email protected] page 1 of 3

 TP78xx-1 Series
TEMPERATURE DERATING GRAPHS EXTERNAL CAPACITOR TABLE

Part Number C1(Ceramic Capacitor) C2(Ceramic Capacitor)

TP781.5-1 10μF/25V 22μF/6.3V
TP781.8-1 10μF/25V 22μF/6.3V
TP782.5-1 10μF/25V 22μF/10V
TP783.3-1 10μF/25V 22μF/16V
TP785.0-1 10μF/25V 22μF/16V

STANDARD APPLICATION CIRCUIT

TP78XX-1

Note:
1. C1 and C2 are required and should be fitted close to the converter pins.
2. The capacitance of C1,C2 sees external capacitor table, it can be increased properly if required, and tantalum or low ESR electrolytic capacitors may also suffice.
3. No parallel connection or plug and play.
TEST CONFIGURATIONS（TA=25℃）
1.Efficiency and Output Voltage Ripple Test 25.4 mm 25.4 mm

12.7 mm

+Vout
+Vin 1 DC/DC Converter 3 Copper strip

1uF 1uF
C1 2 C2 Scope 25.4 mm Load
Ceramic Tantalum

GND Copper strip

2.Start-up and Load Transient Response Test

50.8 mm

+Vout
+Vin 1 DC/DC Converter 3 Copper strip

C1 2 C2 Scope 25.4 mm Load

GND Copper strip

www.gztoppower.com TEL:0086-20-62162688 EMAIL:[email protected] page 2 of 3

 TP78xx-1 Series
OUTPUT RIPPLE REDUCTION
To reduce output ripple, it is recommended to add a LC filter in output port. L: Recommended parameter 10μH ~ 47μH.

MECHANICAL DIMENSIONS PIN CONNECTIONS

SIP Package
HANIONS Pin Function
1 +Vin
TOPPOWER
2 GND
10.20

TP781.5-1
0.50

3 +Vout
YYWW
4.10

5.08 0.50

1 2 3
7.50
1.80

0.30

bottom view

11.60

All dimensions in mm ±0.25.All pins on a 2.54mm pitch.

RECOMMENDED FOOTPRINT DETAILS TUBE OUTLINE DIMENSIONS

9.4
12.2
2.54

16.7

1.15
1.00 33孔
HOLES
0.5

2.54
4.7

Unless otherwise stated all dimensions in mm ±0.5mm.

L=520mm ±2mm Packaging quantity:43PCS
Unless otherwise stated all dimensions in mm ±0.5mm. L=220mm ±2mm Packaging quantity:17PCS

www.gztoppower.com TEL:0086-20-62162688 EMAIL:[email protected] page 3 of 3