DENTAL UNIT AND CHAIR

OPERATING INSTRUCTIONS
This Instruction Manual describes how to use the SP-CLEO II.

A
W

IMPORTANT

Thoroughly read this Instruction Manual before use, and use the SP-CLEO II according to
the instructions.
Keep this Instruction Manual carefully, and read it again whenever it is needed.
This product is a dental unit used for dental care.
People other than dentists and other dental professionals should not use this product.
 TABEL OF CONTENTS

1. SAFETY PRECAUTIONS ------------------------------------------------------------------- P1

2. REQUEST FOR WATER FLUSHOUT (DISCHARGE) ------------------------------ P6

3. OVERALL VIEW AND MAJOR COMPONENTS ------------------------------------ P7

4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS --- P9

5. CARE AND MAINTANANCE ------------------------------------------------------------- P31

6. STORAGE, LIFETIME, DISPODAL AND RESTRICTIONS OF USE ----------- P38

7. BEFORE ASKING FOR REPAIRS ------------------------------------------------------- P39

8. DIMENSION AND SPECIFICATION --------------------------------------------------- P40

9. MAINTANANCE AND INSPECTION -------------------------------------------------- P42

Intended Use of the Product
This product is an active therapeutic device intended to administer or exchange energy of
electric, air and water for the exclusive use for diagnoses, treatments and relative procedures
of dentistry, and its characteristic is not in a potentially hazardous way between such energy
and human body, taking account of the nature, the density and site of application of the energy.
The product must be operated or handled by the qualified dentists or by dental staffs under
the supervision of the dentist.
Such dentists or dental staffs should instruct and/or assist the patients to approach to and
leave from the product.
Patients should not be allowed to operate or handle the product unless he/she is so instructed.
The product is supplied together with the handpieces like electric micromotor, air turbine
and/or motor, scaler and so on.

Environmental Requirements
Ambient Temperature Operating +5℃ - +40℃ 　Storage -10℃ - +50℃
Humidity 10 % - 80%
Atmospherical Pressure 600 hPa - 1060 hPa

Important Notes
In case of the troubles, please contat Takara Belmont offices or your dealers.
Do not disassemble or attempt to repair.
Disassembly, repair or modifications shoud only be done by a qualified repair technician.
Attempts at disassembly, repair or modifications may lead to abnormal operation and accidents.

In case of disposal of equipment

In case of disposal of equipment or of components dismounted from the unit, take full infection
preventing measures, and carry out appropriate steps in accordance with the legal regulations
at that time.
SYMBOLS

Chair last position Chair auto return Chair preset1 Chair preset2

To Recline To raise
To raise the chair To lower the chair
the backrest the backrest

Chair last position Chair auto return Chair preset1 Chair preset2

Chair manual To Recline

Chair auto control To raise te chair
control the backrest

To raise Chair Handpiece coolant

To lower the chair
the backrest manual control spray on/off

Fiber optic Micro motor

Rotation mode
Handpiece Setting handpiece light Forward/Reverse
select
on//off select

Fiber optic
handpiece light Syringe Function Store
on//off

Minus Plus Bowl flush Cupfiller

Dental light on/off Dental light Service outlet Service outlet

mode selection water flow control (water)

Service outlet (air) Water heater

Ｗ Water
Ａ Air

Caution
It means “caution, Type B
warnings, or Manufacturer Applied Parts
possibility to
danger”.
 1. SAFETY PRECAUTIONS

For proper operation, please carefully read through the Safety Precautions before using the product.
Items described herein are provided in order to ensure safe and appropriate use of the product, and to prevent
property damage or personal injury to the operator and other persons.
Furthermore, the precautions describe potential hazards due to improper handling and classify hazards according to
degree of damage and level of urgency.
Please be sure to read the items and precautions as they both relate to safety.

Division of caution level Magnitude of danger and damage and extent of urgency
WA R N I N G This word refers to precautions that if ignored may result in fatal or serious injuries.
This word refers to precautions that if ignored may result in minor or moderate injury
CAUTION
or property damage.
NOTICE This word refers to precautions regarding safety.

WA R N I N G
1. Be sure to switch off the breaker for the equipment when it will not be in use for a long period of time.
When the equipment will not be in use for a long period of time, such as at the end of the day or a non-business
day, be sure to switch off the applicable breaker in the office and disconnect the power plug from the outlet.
Failure to heed this warning may result in electrical leakage or fire due to deterioration of insulation.

2. Be sure to turn off the main switch at the end of the day and during break times.
Be sure to turn off the main switch at the end of the day and during break times. This will prevent
malfunctions and resulting hazards due to accidental contact with the equipment.

3. Do not attempt to disassemble, repair or modify the equipment.

Only authorized personnel should disassemble, repair or modify the equipment. Failure to heed this
warning may cause an accident, failure, electrical shock, or fire.

4. Be sure to ground the equipment

Be sure to ground the equipment firmly and correctly. (To ground the equipment, contact a qualified
technician.) Failure to heed this warning may result in electrical shock during failure or electrical
leakage.

5. Pay attention when exposing the equipment to electromagnetic interference.

The product may malfunction when exposed to electromagnetic interference. Do not install the product
close to communication equipment or an elevator that generates electromagnetic waves. In addition, do not
use devices such as a mobile phone that generates electromagnetic waves in the vicinity of the product.

6. Be sure to turn off the main switch when a high frequency surgical instrument (HF-Surg) is used.
Use of a HF-Surg may cause the equipment to malfunction due to generated noise. Be sure to turn off the
main switch when using the HF-Surg.

7. Use caution towards patients with a pacemaker.

Use caution towards patients with a pacemaker. If the patient experiences anything unusual while
product is operating, immediately turn off the power of the product and discontinue use.

8. Never fail to carry out maintenance and inspections.

Using the product without performing maintenance and inspection programs may result in bodily
injury or property damage.
Refer to pages 43 for instructions on maintenance and inspections.
-1-
 1. SAFETY PRECAUTIONS

WA R N I N G
9. Be sure to mount the mirror cover.
The mirror cover for the dental light must be attached whenever the light is used. Touching the light
bulb may result in burns.
Refer to the operating instructions on the dental light for details.
10. Be sure to turn off the power when replacing the light bulb.
The power must be turned off when replacing the dental light bulb. Failure to heed this warning may
result in electrical shock.
The specified halogen light bulb must be used.
The bulb and the bulb holder may be hot. Wait until they become cool before replacing the bulb.
Do not touch the halogen bulb with bare hands.
Refer to the operating instructions on the dental light for details.

11. Do not place articles weighing 3 kg or more on the instrument table.

Do not place articles weighing 3 kg or more on the instrument table. Failure to heed this warning may
result in breakage, malfunction of the table, or an accident.
12. Do not apply excessive force to the arms.
Do not mount or apply unnecessary force to the unit arms or the armrests of the patient chair. Failure
to heed this warning may cause an accident or the unit to tip over.

CAUTION
1. The system must be operated or handled by a qualified dentist or by dental staff under the supervision of a
Persons other than dentists or other dental professionals must not use the system.

2. Check safety before operating the product.

Before operating the system, be sure to check that all parts operate normally and safely, and that there are no
obstacles in the area.

3. Pay attention to the patient and children.

Be careful to avoid accidents due to mischief or careless operations by the patient (children in particular).
Keep an eye on the patient.

4. Stop operation of the system when feeling something is wrong.

During inspections, pay attention to any looseness, wobbling, inclination, vibration, abnormal sounds,
temperatures, or odors. If something is out of place, even slightly, immediately stop operating the system.

5. Do not strongly hit or scrape the system.

Do not strongly hit or scrape the system. Failure to heed this caution may result in breakage of the cover or
malfunction of the system.
6. Be sure to operate the switches by hand.
Except for the footswitch, be sure to operate the switches by hand. Operation of switches by means other than
hands may result in breakage or system malfunction.
7. Take caution when using water other than city water.
The system is designed for use with city water. Use of water other than city water (such as water-line
sterilization system) may result in system failure.

-2-
 1. SAFETY PRECAUTIONS

CAUTION
8. Request for flushout of water staying in the unit
In order to maintain the quality of the treatment water to stably supply water to the handpieces, be sure
to thoroughly flush out any remaining water in the unit before starting treatment. Refer to the pages for
the flushing out procedures.
9. Cautions when shifting/moving the instrument table:
When moving the instrument table, pay attention to the surrounding area. Failure to heed this warning
may result in injuries by the tips of the handpieces.
The instrument table must be moved with the handle of the unit.
10. Do not place hot objects on the instrument table.
Do not place hot objects on the instrument table. Failure to heed this warning may result in deformation or
discoloration of the table.
11. Be sure to wipe chemicals off immediately when spilled on the system.
If chemicals or water are spilled on the system, immediately wipe off with a dry, soft towel. Failure to
heed this warning may result in system malfunction, electrical leakage, stains, or rust on the equipment.
12. Take care not to activate the water heater without water in it.
Activating the water heater without water in it will burn out the heating element, resulting in fire.
13. Be sure to use the cover over the scaler tip.
After using the scaler, be sure to use the designated tip cover (for models with a cover) before placing
it in the holder. Without the cover, there is a possibility of injury caused by the scaler tip.
14. Observe the following when handling handpieces:
Change the rotation speeds of the micro-motor and detach the burr of the handpieces only after motor
rotation comes to a complete stop for safety purposes. Refer to the operating instructions that come with
each handpiece for details.
15. Observe the following when handling the film viewer:
Handle the film viewer carefully, since a fluorescent lamp is encased. Be sure to turn off the lamp when not
in use.
16. Observe the following concerning the cart hose:
Do not tread on the cart hose. Failure to heed this warning may result in damage to the hose, as well
as people tripping over.
17. Cautions when adjusting the height of the cart-type instrument table:
After adjusting the height, be sure to fasten the loosened lock screw. Failure to heed this warning may
cause the table to shift, resulting in an accident.
18. Pay attention to entrapment during automatic operation of the treatment unit.
During automatic operation of the treatment unit, pay attention to surrounding areas before initiating
operations. Failure to heed this warning may result in breakage of the backrest, stool, or instrument table.
Furthermore, check that the patient is in the correct position and always monitor the patient during system
operation.
19. Caution when cleaning the control panel (membrane switch):
Seepage of sterilization liquid into the back of the membrane sheet will cause switch failure. Be sure to use a
paper towel applied with sterilization liquid to clean the membrane sheet surface.

-3-
 1. SAFETY PRECAUTIONS

CAUTION
20. Observe the following when cleaning the Spittoon bowl:

Never use sandpaper, wire wool, or detergents containing abrasive compounds to clean the Spittoon bowl.
Do not use overly acidic or alkaline pipe cleaning agents, as they may corrode metals.
21. Pay attention to water discharge when detaching the Spittoon bowl.
When detaching the Spittoon bowl, be sure to turn off the main switch; otherwise, the water supply sensor
will sense hands or objects during the detachment, which will activate the bowl flush mechanism. Water
may spray out and leak into areas that may cause rust.
22. Caution when cleaning the plastic covers:
When cleaning the plastic covers, use only the desinfectant (Durr FD333) recommended by this company
or a diluted neutral detergent, or the plastic cover may crack.
After cleaning, make sure to wipe off all residue with a dry and soft cloth.
23. Air pressure of the clean water system (optional) must be less than 0.2Mpa.
The air pressure to the clean water system must be regulated to less than 0.2Mpa. Excessive pressure may
rupture the clean water system.

24. Do not use water for the clean water system (optional) other than purified water, distilled water or pure water.

For the clean water system use only purified water, distilled water or pure water.
Do not use such as mouth wash or electrolytic solution which may cause clogging in tubings or adverse
effect on inner valves and instruments.

25. Close the water main valve at the end of the day.

Make sure to close the water main valve at the end of the day to prevent a water leakage.

NOTICE
1. Operational check of the air compressor:

If air is not supplied to the product, the system will not function even if the main switch is
turned on. Before operating the product, turn on the power to the air compressor.

2. The air turbine must be of the type with a water check valve.
The air turbine must have a water check valve. If the turbine is not the correct type, contact your
dealer or our company.

3. Handling of the system during power failure:

If the system stops during operation due to a power failure, place the handpiece in the holder, and turn off
the main switch.
4. Function of the flow adjustment valve/knob

The function of the flow adjustment valve/knob is to regulate, not to stop, air/water flow.
Do not overly tighten the valve/knob or the knob may break.

-4-
 1.SAFETY PRECAUTIONS

Caution Points During Operation of the Product

Description of Symbol Marks

Caution areas (such as moving parts, rotating parts and detachable parts to which caution should
be paid)
Caution areas that are provided with an emergency stop mechanism

① ② ⑥
③
⑧

④ A
W
⑩

⑦ ⑨
⑤
① Be aware of contact with the assistant’ s ⑥ Take care not to be trapped by the lower part
instrument holder. of the legrest.
The upper body of the patient must not go over the Do not put your feet under the legrest.
cuspidor unit.
⑦ Take care not to be trapped by moving parts
② The cuspidor unit’ s rotation of the headrest.
Make sure that the patient does not lean on the Do not allow hands, fingers, or hair to become
cuspidor unit, as pushing on the spittoon bowl causes it entangled in the moving parts of the headrest.
to swing outwards.
⑧ Take care not to be trapped by the lower part
③ Ensure that the mirror cover is securely in place. of the seat.
The mirror cover must be installed securely. Do not put hands or feet into the gap in the lower
part of the seat.
④ Take care not to be trapped by moving parts of the
backrest. ⑨ Check the locking mechanism of the primary
Do not put hands or feet into the gap between the arm.
backrest and the seat. Check that, when moving the instrument table to
the back of the backrest, the chair lock indicator
⑤ Take care not to be trapped by the armrest. on the control panel (membrane switch) blinks
Do not operate the chair with the right armrest swung red, and operation of the chair is halted.
out 180 degrees.
⑩ Be aware of interference between the chair
and the table.
Do not move the table under the moving parts of
the chair.

-5-
 2. REQUEST FOR WATER FLUSHOUT (DISCHARGE)
E type:Standard Ｅ
Precautions for water quality safety A type:Option Ａ
CAUTION
To maintain the water quality for treatment and for stable water supply to the handpieces, ensure to carry out
flushout of the residual water in the unit before starting treatment.
At the beginning of the week or in the morning, that is, a long period of idle time, the residual water in tubings
and water heater in the unit tends to permit bacteria being propageted.
Ensure to carry out flushout of water lines in the unit before starting treatment, for the safe treatment and for the
operation of the handpiece without any problem.
It is also recommended to flush out the residual water in the unit and in handpiece tubings with fresh water, after
the treatment in the morning and also in the evening to prevent bacteria propagation.

Standard length of time required for flushout of water lines in the unit
Handpiece line About 40 seconds per each of turbine, motor, scaler and syringe.
Air Turbine (About 40 seconds also in case of flushout of all of them in a batch.)
Micro Motor CAUTION
Scaler Apply flushout to the scaler with the body kept fitted. Failure
Syringe (for both doctor / assistant) may result otherwise.
Cuspidor line
Cupfiller (water heater) About 5 minutes for cleaning water in cupfiller line.
Bowl flush

Flushout procedure Ｅ
Handpiece line Mode I: For Flushing out Mode II: For Flushing
Pick up one handpiece out of the holder, and hold it the Handpiece water line out the cupfiller and
over the cuspidor bowl with the turbine kept as it is only cuspidor bowl after
and the contra angle connected to the motor. As for flushout procedures, handpiece flushout
(In case the flushout function is provided, pick up please refer to Page 25 As for flushout
all the handpieces in a lump from the holder, and selection and operation of procedures, please refer
hold them on the cuspidor bowl.) flushout Mode I. to Page 25 Selection and
operation of flushout
Cuspidor line
Mode II.
Cupfiller (water heater)
Bowl flush

Flushout procedure Ａ
Handpiece line
Pick up one handpiece out of the holder, and hold it
over the cuspidor bowl with the turbine kept as it is * Applicable when flush-out function was selected as
and the contra angle connected to the motor. optional.
( *In case the flushout function is provided, pick up Turn the toggle switch on and flush-out the handpiece
all the handpieces in a lump from the holder, and
hold them over the cuspidor bowl.)

Cuspidor line Repeat cupfilling a few times. (at least 3 times)

Cupfiller (water heater) Press the bowl flush switch and keep flushing the
Bowl flush cuspidor bowl for 5 minutes.

-6-
 3. OVERALL VIEW AND MAJOR COMPONENTS

Base Mount Type

Cuspidor Bowl

Doctor Control Panel

Assistant Instruments Holder Doctor Table

Balance Arm

Foot Controller
Doctor Instruments Holder

Manual Switch
Auto Switch

Main Switch

-7-
 3. OVERALL VIEW AND MAJOR COMPONENTS

Docotor Table Section

Holder Type Ｅ Ａ Place Holder Type Ｅ Ａ Cart Type Ｅ Ａ
Tray Mat

Tray Mat Tray Mat Doctor Control Panel

Doctor Control Panel Doctor Control Panel
Handle

Handle Handle

Brake Brake Doctor Instruments Holder

(Holder Type)

Doctor Instruments Holder Doctor Instruments Holder

(Holder Type) (Place Type)

Cuspidor Section
Cupfiller Nozzle

Bowl Flush Nozzle

Cuspidor Bowl

Assistant Membrane Switch

Cuspidor Maintenance Panel

Solid Collector

Light Post
Front Panel

Assistnat Instruments Holder Dental Light Sensor/Manual Switch

(applicable only for AL-520, AL-820S and
900 Dental light type 920)

Assistnat Arm Service Outlet for Air (Optional)

Service Outlet for Water with regulator

Junction Box Cover

Junction Box Section

Water Master Valve
Air main valve (inside utility box) Air Master Valve

Turn clockwise to close and counter-clockwise to open.

Use a flat head (-) screwdriver for opening/closing.

Water main valve (inside utility box)

Turn clockwise to close and counter-clockwise to open. Drain Valve

Air Pressure Gauge

Drain valve
This valve is for draining the water in the air filter. Water Pressure Gauge

-8-
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

1. Chair Section
1-1. Main Switch

Lit in green when the switch is on.

ＯＦＦ ＯＮ

Main Switch

1-2. Armrest ① ②

1 Hold the armrest on the right-hand side, and release the

lock by pulling up the armrest diagonally backward (in a
direction that is parallel to the armrest axis) by about 1 cm.
(The lock is released when the armrest is pulled up to a
point where hitting sensation is felt.)
2 Turn the armrest to 9 o’clock direction. (The armrest can
turn by about 180 degrees.)

* For returning the armrest to the former position, observe the procedure, which is opposite to that of lock
release. That is, turn the armrest to the normal working position, and then lock the armrest in position by
pushing it down diagonally forward, which is opposite to the direction mentioned in item 1 above.
Make sure to confirm that the armrest is in the locked safe position before use.

CAUTION
The armrest approaches the floor when the backrest is tilted as
shown to the left. Never operate the chair in the state where the
armrest is turned out of the normal working position. A part of
the human body or any other article may be caught between the
armrest and floor otherwise.

1-3. Headrest
Headrest
1) Height Adjustment Release Button
Press down or pull up the headrest to the desired height. Bar

2) Angle Adjustment
Grasp the headrest release button on headrest mechanism
and move to desired position.

CAUTION
Before moving the headrest, confirm that the patient is placing his/her head in a normal position,
and never leave the patient unsupervised while the headrest is in motion.
Do not use the headrest in a position where the patient feels painful.
Before moving the headrest, confirm that there is no obstacle around it lest a part of the human body
or any other article be caught between the headrest and backrest.

-9-
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS
1-4. Stick Switch
Auto Switch
Auto Switch
1) Preset Control
The chair has two preset positions.
(Preset-1 and Preset-2) Momentarily depress the
auto mode stick switch to left side, the chair will
Manual Switch
move to the preset-1 position automatically.
(Preset-2 is operated by right side.)
2) Auto Return
Momentarily depress the auto mode stick switch to
upward, the chair will return to the initial position.
(The seat is fully lowered and the backrest is in the upright position.),
3) Last Position Memory
Momentarily depress the auto mode stick switch to downward at the reclined backrest position (treatment position),
the backrest will raise to the mouth rinsing position automatically. Momentarily depress the auto mode stick switch
to downward again, the backrest will recline to the previous treatment position automatically.
4) Emergency Stop
During automatic procedure (Preset, Auto return and Last position memory), depress of any side of the
stick switch will cancel the automatic movement immediately.
Note : Do not depress the auto mode stick switch for over 3 seconds, because the memorized position
in auto mode may be changed.

Manual Switch
1) Seat Lifting
Keep depressing the manual mode stick switch to upward until the seat is lifted up to the desired position.
2) Seat Lowering
Keep depressing the manual mode stick switch to downward until the seat is lowered to the desired position.
3) Backrest Reclining
Keep depressing the manual mode stick switch to left side until the backrest is reclined to the desired position.
4) Backrest Raising
Keep depressing the manual mode stick switch to right side until the backrest is rased up to the desired position.

Up tilt Limit position

Positional relation between Backrest position and 1
0

Legrest movement/Rollup extension.

2
1) Legrest raising angle and rollup extension are
At the 3 & 4 position of
automatically controlled by backrest angle at 3 backrest angle,
rollup extends most
preset positions only.
You can’t manually raise legrest nor use 4
At 4 position
rollup extension.
Lay flat At 3 position
Limit position
At 2 position
At 1 position
At 0 position

At the 0 , 1 & 2 position of backrest

angle, rollup does not extend.

- 10 -
 Handpiece Pressure Gauge

4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2. Doctor Unit Section

2-1. Main switch Ｅ Ａ

Main Switch ON OFF

When the main switch is turned on, the MAIN LED on the doctor
membrane switch panel lights up in green. This state permits
motion of the unit, chair and dental light.. The unit can be moved Lit in green

even while the chair is OFF. MAIN

When the main switch is turned on, all the lamps on the doctor Indicator

membrane switch panel light up, and the following is displayed on

the indicator.
Ｅ Ａ
Belmont 　　　　Ｖｅr.　**　♪
　Ｔakara 　Ｂelmont 　０

Program version No.

A few seconds later,
Belmont
　

is displayed and all the functions can be operated.

* The lamps turn off automatically if the equipment is not used for a
certain length of time. But they light up again when any operation
is performed.
2-2. Indicator Ｅ Ａ
If any error arises to the memory, the buzzer sounds and [EEPROM READ ERR] is displayed on the
indicator. Once turn off the main switch and then turn on the main switch again. If an error message is
still displayed, please contact your dealer or our office.
* This doctor unit section is actuated by compressed air. Therefore, ensure that the air compressor is
working.

Indicator off function

The indicator is off if no operation is performed for a fixed length of time. This function is provided
for preventing fluorescent lamp seizure and for power saving.
1. 120 seconds after steady state display appeared since the main switch (power) was turned on.
2. 30 seconds after normal operation
The indicator is restored when any operation is attempted.

Indicator abnormality and troubleshooting

There are cases where the display on the indicator becomes abnormal due to noise.
In such a case, turn off the main switch and turn it on again about 5 seconds later.
* However, there is a possibility where reset does not occur if noise is continuing.
Eliminate the cause for the noise, and then turn on the power again.
If it is not possible to identify the cause for the noise, please contact your dealer or our office.

- 11 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS
2-3. Handpiece Ｅ Ａ
When the main switch is turned on, whether handpieces
are accurately fitted in instrument holders or not is checked
automatically. If any handpiece is not accurately fitted in its
instrument holder at this occasion, the subject holder number
(counted as No. 1, 2 and so forth from facing left excluding
syringe) is displayed on the indicator and the buzzer sounds for
a few seconds. Accurately fit the handpiece in the displayed

ge
rin
holder.

Sy

.1
O

.2
N
NO
If the handpiece is accurately fitted while the buzzer sounds

.3
O

.4
N

O
(for a few seconds), the buzzer stops, and the section become

N
operative.
If the buzzer stops in the mid-way of the work, turn off the main
switch, accurately fit the handpiece and turn on the main switch
again about 5 seconds later. Then, use of the section is permitted.
GE
RIN
SY .1
NO .2
NO .3
NO .4
NO

The handpiece is actuated by picking it up from the handpiece holder and operating the foot controller.
See pages 25 to 30 for operation of foot controller, micromotor and electric scaler.

2-4. Handpiece priority function (first priority) Ｅ Ａ

Only one handpiece, which was picked up first of all, is operable.
The holder No. of the operable handpiece is displayed on the indicator.
Ｎｏ．1
If multiple handpieces are picked up in succession from the holder,
and the handpiece that was picked up first is returned to the holder,
error display [ERR] appears on the indicator. ＥＲＲ
If error display appears, the normal state will be restored when all the
handpieces are fitted in the holder.

2-5. Handpiece air pressure gauge Handpiece Pressure Gauge

Displays the handpiece drive air pressure.

CAUTION
Holder Support Arm / Hndpiece Holder
Do not adjust the holder support arm and handpiece
holder.
Because the angle adjustment of the holder is fixed at Handpiece Holder
Holder Support Arm
the point of installation, the holder support arm will
be damaged in case it is moved too hard.

- 12 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2-6. Handpiece spray flow rate control

The handpiece spray flow rate can be adjusted by turning
1 knobs (with blue caps) of the doctor section.

2-7. Syringe spray water and air control

The syringe water and air flow rate can be adjusted by turning
2 knobs of the doctor section. ①
Doctor table front arrow view
Blue cap ------ Water
Yellow cap --- Air

* With each one of these knobs, the flow rate decreases when
the knob is turned clockwise, and the flow rate increases
when the knob is turned counterclockwise.
4 6 7 8 9
②
Doctor table front arrow view

Increase Decrease

* The flow rate control knobs are provided for increasing/

decreasing the flow rate, and they are not stop valves.
Note that the knob will idle if it is shut off with force.

2-8. Balance arm brake Ｅ ＥＡ Ａ

For base mount type Balance Arm Brake
Release Button
Use this button for releasing the balance arm brake to raise or
lower the table.
Keep this button pressed while raising or lowering the table.

For cart type

Loosen the column knob to raise or lower the table.
Fix the table in place by firmly tightening the column knob
after adjustment. Column Knob

CAUTION
Do not place a load of over 3 kg on the table, or table damage,
malfunction and failure may be caused.

NOTICE: Noise might be produced due to impact at the time of table stop if the table is moved
upward or downward without pressing the brake release button. Make sure to carry out table height
adjustment while the brake release button is pressed.

- 13 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2-9. Motion stop locking device Ｅ

ＥＡＡ
While the doctor table is located behind the chair, auto
motion stop lock is applied for preventing damage to the
doctor table.
Lock
Auto motion stop lock is released when the doctor table is
returned to the normal care position.

Lock

2-10. Intra-oral size filmviewer (optional) Ｅ

ＥＡＡ
The screen light is lit when the switch is pressed, and the screen
light is off when the switch is pressed again.

NOTICE: Turn off the light when the filmviewer is not used.
Switch
2-11. Panorama size filmviewer (optional) Ｅ ＥＡ Ａ
The screen light is lit when the switch is turned to the upper
Switch
position, and the screen light is off when the switch is turned to
the lower position.
- The screen brightness increases when the brightness control dial
is turned upward, and the screen brightness decreases when the Brightness
control dial
brightness control dial is turned downward.

NOTICE: Turn off the light when the filmviewer is not used.

2-12. Type 77, 3-way syringe Ｅ ＥＡ Ａ

Water jets out when the button with W mark is pressed. Air jets Water Air
out when the button with A mark is pressed. If both buttons are
pressed simultaneously, then spray jets out.
Ａ
Ｗ

The nozzle turns by 360 deg.

CAUTION Nozzle
Do not drop the 3-way syringe. (Damage to the syringe and
deformation to the nozzle could be caused.)

- 14 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2-13. Foot controller

Type A2 (A Type)Ｅ Ａ
Pedal
The pedal depressing extent can control the turbine rotation
speed and air scaler output. Coolant Swtich

The electric scaler (optional) is activated when the pedal is OFF

depressed. Control the output by the scaler output control
knob. ON

Coolant switch
Cooling spray works when the coolant switch is turned to the
ON side and a handpiece is then actuated. Increase or decrease
by the pedal
Chip blow button

depressing extent
Chip blow button Pedal
Chip air is delivered out of the turbine when the chip blow
button is depressed.

Scaler control nob

Type SE (E Type) Ｅ Ａ
Pedal
The pedal depressing extent can control the turbine rotation
speed and air scaler output.
- The motor rotation is activated when the pedal is depressed.
The rotation increases when the pedal is slided to the right, and
decreases when the pedal is slided to the left. Coolant Switch
The electric scaler output also increases when the pedal is
slided to the right, and decreases when the pedal is shifted to
the left. The P-MAX scaler does not permit output control
during operation. Once stop the operation, control the output,
and restart the operation.
Decrease
Coolant switch Chip Blow Button
Depressing the coolant switch turns spray on/off like
Pedal
membrane switch on the table.
Increase

4-mode (Water -> Air -> OFF -> Spray) operation can be
selected for the motor.

Chip blow switch

Chip air for blowing off the chips jets out of the handpiece
when the chip blow switch is depressed.

- 15 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2-14. Description of membrane switch panel

An overview of display on the membrane switch panel and each switch on this membrane switch panel
is shown in the figure below.
For datailed operating instruction please see pages 14-18.
Each switch on the membrane switch panel provides multiple functions, and various actions can be set
When combined with the function switch.
17
Ｅ Ａ
15 8 9 13 14 4 3 6 5

16 11 10 12 2 1 7

1 Chair manual switch 9 Handpiece light switch

The chair moves while this switch is pressed. Switch for turning on the handpiece fiber-optic light.
2 Chair preset switch 10 Micromotor forward/reverse select switch
The chair moves to the set position when this Switch for switching the micromotor rotation direction.
switch is pressed. 11 Rotation mode select switch
3 Chair auto return switch Switch for switching between micromotor rotation
The chair moves to the initial position when this limit and preset modes.
switch is pressed. 12 (-) (+) switches.
4 Chair last position switch Switches for setting-up mode selection, timer setup and
The chair moves to the rinsing position or treatment so forth.
position each time when this switch is pressed. 13 Function switch
5 Cuspidor flush switch Switch for setting-up various operating conditions.
Switch for flushing cuspidor bowl. 14 Store switch
6 Cupfiller switch Switch for storing set data.
Switch for filling water to the cup 15 Main switch indicator lamp
7 Dental light switch This indicator lights up when the main switch is on.
Switch for turning on the dental light. 16 Chair motion lock indicator lamp
8 Spray on/off switch This indicator lamp is lit while chair motion is locked.
Switch for on/off of handpiece coolant spray. 17 Indicator

Ｅ Ａ 15 4 3 1

16 2 9 5 6

- 16 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

1 Chair manual switch ＥＡ

Ｅ Ａ
Ｅ Ａ Ｅ Ａ
Switches for manual up/down/backrest reclining of the chair.
Press to raise the chair.
Press to lower the chair.
Press to recline the backrest.
Press to get up the backrest.

2 Chair preset switch ＥＡ

Ｅ Ａ
Set the chair height and backrest angle in desired position(s), and
actuate the chair by either one of these switches.
Press any switches(chair/unit) for stopping the automatic movement.

3 Chair auto return switch ＥＡ

Ｅ Ａ
When this switch is pressed, the chair moves downward to the initial
position, and the backrest rises to upright position.
Press any switches(chair/unit) for stopping automatic movement.

4 Chair last position switch ＥＡ

Ｅ Ａ
When this switch is pressed in the fine-adjusted treatment position, the
chair moves to the rinsing position. When the switch is pressed again,
the chair returns to the former treatment position.

Preset position setup procedures

1. Move the chair to the treatment position using manual switches.
2. Upon deciding of the desired treatment position, keep pressing preset switch , or to be set
for about 5 seconds. The buzzer sounds from the chair, and setup has been completed.
3. To change the set position, perform the procedures steps 1 and 2 above.

Last position setup procedures

1. Move the chair to the rinsing position using manual switches.
2. Upon deciding the desired rinsing position, keep pressing last position switch for about 5 seconds.
The buzzer sounds from the chair, and setup has been completed.
3. To change the set position, perform the procedures steps 1 and 2 above.

CAUTION
When operating the chair by the auto return switch, be careful not to nip the stool or the like by the
chair backrest. Damage to the backrest, stool and/or doctor table could be caused. Furthermore, at
the time of motion of the chair, ensure that the patient is sitting in a normal position and keep your
eye on the patient while the chair is in motion.

- 17 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

5 Cuspidor bowl flush switch ＥＡ

Ｅ Ａ
When this switch is pressed, water comes out of the bowl flush nozzle Ｅ Ａ Ｅ Ａ
and flushes the cuspidor bowl. The timer is set for about 5 seconds.
For continuous bowl flushing keep pressing this switch is for 2 seconds
or longer.
Press the cuspidor flush switch again for stopping flushing.

6 Cupfiller switch ＥＡ
Ｅ Ａ
Water is supplied through the cupfiller nozzle when this switch is
Ｅ Ａ Ｅ Ａ
pressed. Simultaneous with start-up of cupfiller motion, water comes
out of the bowl flush nozzle and flushes the cuspidor bowl.
* The cupfiller is timed for 3 to 4 seconds, and press the switch again
to stop in the middle. When the cupfiller switch is pressed, water
is supplied automatically for 3 to 4 seconds irrelevant to the water
volume in the cup. Watch the overflow. Do not press the switch while
the cup is not in place.

7 Dental light on/off switch Ｅ Ａ

Switch for on/off the dental light.
* There are cases where this switch cannot be used depending on the
unit specification and the type of dental light.

8 Spray on/off switch Ｅ Ａ

Switch for on/pff the handpiece coolant spray. A (AIR) ......... ORANGE
W (WATER)... GREEN
When a handpiece is picked up and this switch is pressed, either LED A
(air) or LED W (water) located on the left-hand side or right-hand side
of the switch lights up, and indicates the selected function.
In case of air motor or air turbine, switching between spray (both of
LED A and LED W are lit) and OFF occurs when this switch is pressed.
In case of electric scaler, switching between water only (LED W is lit)
and OFF occurs when this switch is pressed, regardless of the mode. 2-Mode 4-Mode
In case of micromotor, either the 2-mode or the 4-mode can be selected Spray ON Spray
by mode select setup. Water
Spray OFF
When this switch is pressed in the 2-mode setup, switching between Air

spray and OFF occurs. OFF

In case of 4-mode setup, switching occurs in the sequence indicated

below each time when this switch is pressed: Spray to Water only to Air
only to OFF
Case where handpiece light is "ON"
9 Handpiece light on/off switch Ｅ
ＥＡＡ (LED is lit in green.)
Switch for on/off the handpiece light.
Switching between on and off of the handpiece light occurs each time
when this switch is pressed.
Ｅ Ａ Ｅ Ａ

- 18 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

10 Micromotor forward/reverse select switch Ｅ Ａ

Use this switch for switching the micromotor rotation direction.
Pressing this switch each time changes the direction between For reverse turning For forward turning
(Only left-side LED (Only right-side LED
forward (clockwise) rotation and reverse (counter-clockwise) is lit in orange.) is lit in green.)
rotation.
Forward rotation is preset power is on. In case a micromotor set
for reverse rotation is returned to its holder, the LED indicates
forward rotation. When such a micromotor is picked up, however,
the LED indicates reverse rotation and the alarm buzzer sounds.

* Handpiece rotation stop function

If a handpiece is picked out of the holder in the state where the foot Lit in Orange

controller pedal is depressed, the micromotor of this handpiece will

not run.
The indicator lamp in the micromotor forward/reverse select switch
flickers in orange in this state and thus indicates that the safety
mechanism is working.
Make sure to pick up a handpiece first, and then depress the foot
controller for operation.

11 Rotation mode select switch Ｅ Ａ

This switch is mainly used for switching between micromotor's
rotation limit speed and preset rotation speeds (SET 1 to SET 3).
Pressing this switch each time changes the speed mode: Limit speed
-> SET1 -> SET2 -> SET3 -> Limit speed.
The indicator indicates the selected mode.

12 (-) (+) switches Ｅ Ａ

These switches are used mainly for switching the handpiece setup
mode.
When the switch or switch is pressed, the upper limit of the
micromotor rotation speed changes in three steps (or 5 steps).
The indicator indicates the selected mode.

- 19 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

13 Function switch Ｅ Ａ
Use this switch for setting various working conditions.
The setup function changes in the sequence indicated below each
time when this switch is pressed.
1. Dental timer time setup and motion
2. Doctor number selection
3. Flushout selection and operation
4. Key touch tone selection and change
5. Handpiece light switching-on timing selection
6. Dental timer time-out alarm tone selection
7. Micromotor limit rotation speed selection
8. Micromotor spray mode selection
9. Cupfiller and bowl flush interlocked action selection
* Do not keep this switch pressed.

14 Store switch Ｅ Ａ
Use this switch for storing data and so forth:
1. Store micromotor preset mode. See page 45 for the setup procedure.
2. Store preset timer.
3. Store micromotor recurrence mode at the time of power on.

16 Chair motion stop function (safety function)Ｅ Ａ Ｅ Ａ

The safety mechanism that inhibits chair motion works while any of
the following actions is taken. The "LOCK" LED indicator lamp is lit
LED lit in Orange
in orange in this state.
Setup is in progress with function switch on the doctor membrane ＬＯＣＫ
switch panel.
Foot controller is being depressed.
When the doctor table is turned to the back side of the backrest, auto
motion of the chair is locked and the chair lock indicator on the table
begins to flicker in orange.

- 20 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2-15. Micromotor operation and display Ｅ Ａ

2-15-1. Description of micromotor rotation modes and operation
Two modes, that is, limit rotation (limit mode) and preset rotation
Limit Rotation
(preset mode), are available for micromotor rotation. Either one of
these modes can be selected by pressing this switch. SET1

The limit mode is a rotation mode providing an upper limit speed in SET2
the rotation.
SET3
The preset mode (SET1 to SET3) keeps the rotation speed fixed
regardless how the the foot controller is operated.
Pressing the switch each time changes the speed mode:
Limit speed -> SET1 -> SET2 -> SET3 -> Limit speed.

2-15-2. Operation for switching to limit rotation (limit mode)

Turn on the main switch and pick up a micromotor from the holder.
The rotation mode is displayed on the indicator.
For switching the rotation mode to the limit mode, select the limit
mode by pressing the switch on the membrane switch panel.
For switching the upper limit in the limit mode, press the (-) switch Limit revolution(rpm)
or (+) switch on the membrane switch panel. The rotation upper
limit changes in three steps (or 5 steps).
No.1　40000
Upper limit of rotation in case of three steps
25000rpm
10000/20000/40000 rpm
Upper limit of rotation in case of five steps
5000/10000/20000/30000/40000 rpm
See page 28 for selection of three steps or five steps.
The micromotor rotation speed can be changed in the range of up to
the selected upper limit by sliding the foot controller pedal right and
left. The rotation speed range varies by the micromotor type.

2-15-3. Operation for switching to preset rotation (preset mode)

For switching from the limit mode to the preset mode, select the
preset mode (SET1 to SET3) by pressing the switch on the
membrane switch panel.
Preset revolution (SET1)
For changing the rotation speed in the preset mode, press the (-)
switch on the membrane switch panel to decrease the rotation, or
press the (+) switch to increase the rotation.
No.1　SET1
10000rpm
To store the changed rotation, press the switch . If the main
Revolution (rpm) of preset revolution (SET1)
switch is turned off without pressing this store switch, the set value
before the change is restored.
See page for details of setup.
The micromotor runs at the fixed rotation speed indicated on the
indicator when the foot controller is depressed upon selection of the
preset mode (SET1 to SET3).
(The rotation speed shown in the figure is for reference only.)

- 21 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2-15-4. Description of recurrence mode at the time of power on and setup

This recurrence mode is the rotation mode that always appears first
when a micromotor is picked up after the main switch is turned on. No.2　SET2
It is convenient if a rotation mode frequently used is set as the 20000rpm
recurrence mode.

[Procedure for setup]

1. Turn on the main switch, and pick up a micromotor from the holder.
2. Select a desired rotation mode (limit mode or preset mode) to be set.
3. Press the store switch for about 2 seconds and the buzzer
sounds to confirm that setup of the selected rotation mode has been
completed.

2-16. Operation and display of electric scaler Ｅ Ａ

When the VARIOS scaler or P-MAX scaler is picked up from the

holder, the selected mode is displayed on the indicator, either PERIO,
ENDO or SCALING.
For switching the mode, use the (-) switch or (+) switch on the
membrane switch panel.
The EMS scaler does not provide this mode selection.
The selected mode is displayed
Sliding the foot controller pedal right and left can change the output
of the P-MAX scaler. Ｎo.４　　ＳＣＡＬＩＮＧ
When the pedal slides to the right-hand end, the output becomes the
maximum, and the output is displayed by a bar graph on the indicator Bar graph (1 ~ 8)
even before the operation begins.
The P-MAX scaler does not permit output change during operation.
Once stop the motion, adjust the output, and restart the operation.

Mode switching
Sliding the foot controller pedal right and left can change the output
of the VARIOS scaler or EMS scaler during operation.
When the pedal slides to the right-hand end, the output becomes the
maximum, and the output is displayed by a bar graph on the indicator
during the operation.

CAUTION
Carefully read the instruction manual and other documents attached to each scaler before use,
and correctly use the scaler

- 22 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2-17. Function switch Ｅ Ａ

2-17-1. Contents and sequence of function switch

Indicator
Function Switch

The contents of display on the indicator on the doctor membrane switch panel change sequentially
each time when the function switch is pressed to select a desired setup. Contents and sequence of
function switch setup are described below.

1 Setup and operation of dental timer

① TIMER SET 　　　　　Ｆ＝↓

＝ START
2 Selection of doctor number
② Dr NUMBER ＝０　　　　　↓

3 Selection and operation of flushout

③ FLUSH OUT 　　　　　Ｆ＝↓

4 Selection and change of key touch tone (－)＝HP　(＋）＝HP＋

BEEP＝ON 　　Ｆ＝↓
④
5 Selection of handpiece light switching-on timing
（－）＝OFF　　(＋）＝ON
(Example) Case of "with switch tone"

Selection of alarm tone upon time-up of dental timer

⑤
6
LP.MODE＝HOLD　 　Ｆ＝↓

（－）＝FOOT　(＋）＝HOLD
(Example) Case of holder mode
7 Selection of number of steps of micromotor limit rotation speed ⑥ ALARM TYPE ＝０　Ｆ＝↓

０　１ ２ LP (３)　PUSH

8 Selection of micromotor spray mode ⑦ M LMT＝３STEP 　Ｆ＝↓

（－）＝３　(＋）＝５STEP
9 Selection of interlocked action of cupfiller and bowl flush
⑧ SPRAY＝４MODE 　　　　Ｆ＝↓

10 Return to normal action.

（－）＝２　(＋）＝４　MODE

⑨ ＊ 　　　＝LINK　　　Ｆ＝Ｅ
（－）＝IND　(＋）＝LINK

* Normal action is restored during setup if the next operation ⑩ ＢＥＬＭＯＮＴ　　　　　　

is not applied within about 10 seconds.

- 23 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

1 Setup of dental timer and operation

A subtraction timer is built in.
The maximum settable time is 90 minutes and 50 seconds, and
setup in 10-second units is permitted.
Preset of four different times is permitted.
A preset time can be called by chair preset switch or TIMER SET 　　　Ｆ＝↓

. ＝ START 01：10

[Operation of timer function]

1. Press the function switch once.
2. Set the desired time.
To increase by 1 minute at a time ... (-) switch
(Continuous increase occurs if the switch is kept pressed.)
To increase by 10 seconds at a time ... (+) switch START

(Continuous increase occurs if the switch is kept pressed.)

3. Count-down starts when rotation mode select switch is
pressed.
4. When the timer time is reduced to 00:00, the alarm sounds
to inform that the set length of time has elapsed.

[Procedure for setup of preset timer]

1. Press the function switch once. After the set time has elapsed

2. Set the desired time.

To increase by 1 minute at a time ... switch
To increase by 10 seconds at a time ... switch Press once

3. Press store switch .

4. Press one of chair preset switches and to be
set. Four different preset timers can be set.

[Procedure for use of preset timer]

1. Press the function switch once.
2. Press the chair preset switch or to be called.
3. Start the timer by pressing rotation mode select switch .
4. When the set timer time elapses, the alarm sounds to inform
that the set length of time has elapsed.

[Timer cancellation]
This is the procedure for cancellation of the dental timer during Press once

countdown action.
1. Press the function switch once. Press once
2. Press rotation mode select switch .
TIMER SER 　　　Ｆ＝↓

＝ STOP 01：10

- 24 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

2 Selection of doctor number

Chair positions and handpiece initial setup for four different Dr NUMBER＝０ 　　　　　↓
doctors can be stored.
Micromotor preset rotation speed, and on/off statue of light
pack and spray. (3 positions per each doctor)
Micromotor motion state at the time of power on, and dental
light switch on/off state.
Chair preset position. (Up to 3 positions for each doctor)
Dental light intensity. (2 positions, that is, high/low, for each
doctor) ０ ・・・Doctor Number＝０
Dental timer preset time. １ ・・・Doctor Number＝１
Light pack residual lighting time. ２ ・・・Doctor Number＝２
・・・Doctor Number＝３
* If you want to change setup of the light pack residual lighting
LP

time, please contact your dealer or our office.

[Procedure for setup]
1. Press the function switch twice.
2. Press one switch from and for selection.

3 Selection and operation of flushout FLUSH OUT 　　　　　Ｆ＝↓

A flushout procedure can be selected from two procedures. (－)＝HP　(＋）＝HP＋
[Procedure for operation]
I. Case of flushout of handpiece water line only After operation of 1. and 2

1. Press the function switch three times. min.

2. Press the (-) switch. (Example) Case of full flushout of HP

3. Pick up the handpiece to be flushed, and set it over the PUSH FOOT PEDAL
cuspidor bowl or the like.
▲

１　２　３　４ Ｆ ００：４０

4. Depress the foot controller pedal. Then release the pedal, and ▲
The ID number of the picked up HP is displayed.
▲
the water jets out of the handpiece for 40 seconds .
(HP numbers are 1, 2, 3 and 4 from front left.)

II. Case of flushout of cupfiller and cuspidor bowl after

The residual time is displayed.
(Starts from 40 seconds.

termination of handpiece flushout

1. Press the function switch three times.
2. Press the (+) switch. FLUSH OUT 　　　　　Ｆ＝↓

3. Pick up the handpiece to be flushed, and set it over the (－)＝HP　(＋）＝HP＋

cuspidor bowl or the like.

After operation of 1. and 2
4. Depress the foot controller pedal. Then release the pedal, and
sec.
the water jets out of the handpiece for 5 minutes.
On termination of handpiece flushout, water is delivered (Example) Case of full flushout of HP

out of the cupfiller and cuspidor nozzles simultaneously for 5

PUSH FOOT PEDAL
▲

１　２　３　４ Ｆ ０５：００
minutes for cuspidor bowl flushout.
▲
* To stop flushout action in mid-way, press any switch or The residual time is displayed. (Starts from 5
minutes, and after termination of handpiece
depress the foot controller pedal.
flushout, starts from 5 minutes again.)

* Normal action is restored unless the or switch is Cupfiller Nozzle

Pedal
Bowl Flush Nozzle
pressed within about 10 seconds after the function switch was Spittoon Bowl

pressed.

- 25 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

4 Selection and change of key touch tone

With or without beep tone that is issued when a switch is BEEP＝ON 　　Ｆ＝↓

pressed can be selected, and the beep tone frequency (tone （－）＝OFF 　(＋）＝ON

quality) can be changed. (Example) Case of "with switch tone"

(It is not possible to control the volume of the selected

Tone off Tone on
frequency.)

[Procedure for setup] min. sec.

1. Press the function switch four times.

Frequency High
2. Press the relevant setup switches from the following.
To turn off the tone --------------------------
To sound the tone ----------------------------
To increase the frequency ------------------
To decrease the frequency ------------------
To change the frequency to initial setup -- Frequency Low

[Precautions for change to frequency]

Return to initial setup
Ensure to press the switch on finishing the frequency
change.
The contents of frequency setup are not displayed on the
indicator. However, the switch tone sounds each time when
the frequency is changed. Confirm the frequency change by
Press once
hearing the tone. sec.

5 Selection of handpiece light on timing

The handpiece light on timing can be selected from the two
mode: LP.MODE＝HOLD 　　Ｆ＝↓
1) Rotation mode （－）＝FOOT 　(＋）＝HOLD
The light is turned on while the handpiece is running, and is off
(Example) Case of holder mode
upon elapse of the set light remaining time after termination of
handpiece running.
2) Holder mode Revolution mode holder mode
The light is turned on when the handpiece is picked out of the
holder.
min. sec.

[Procedure for setup]

1. Press the function switch five times.
2. Press the desired setup switch.
Rotation mode ----- switch
Holder mode ------- switch

- 26 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

6 Selection of alarm sound upon time-up of dental timer

The alarm sounds on termination of timer time after countdown ALARM TYPE＝０ Ｆ＝↓

of dental timer. ０　１　２　LP　（３） PUSH

Four alarm patterns are provided, and even in case where
multiple chairs are installed in the same room, the chair from
which the alarm sounds can be easily identified if different
alarm patters are set.

[Procedure for setup]

1. Press the function switch six times.
2. Press a desired chair setup switch from and .

7 Selection of number of steps of micromotor limit rotation

The number of steps of micromotor limit rotation can be
selected from 3 steps and 5 steps.
Case of 3 steps
M LMT＝３STEP 　Ｆ＝↓

Case of 5 steps （－）＝３　　(＋）＝５STEP

(Example) Case where revolution is of "3 steps"

(The rotation values indicated above are given for reference
only.)
3 steps 5 steps

[Procedure for setup]

1. Press the function switch seven times . min. sec.

2. Press the desired setup switch.

3 steps --- switch
5 steps --- switch

8 Selection of micromotor spray mode

Case of 2 modes
Micromotor spray on/off only.
SPRAY　　 ＝２MODE 　　Ｆ＝↓
Case of 4 modes
Micromotor spray on/off, water only and air only. （－）＝２　　(＋）＝４ 　MODE

Example) Case of micromotor spray 2-modes

[Procedure for setup]
1. Press the function switch eight times.
2. Press the desired setup switch.
min. sec.
2 modes --- switch
4 modes --- switch

- 27 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

9 Selection of interlocked action of cupfiller and bowl flush

Selection is permitted from two procedures. ＝LINK 　　　Ｆ＝Ｅ
Case of non-interlock （－）＝IND 　(＋）＝LINK
Flushout of the cuspidor bowl is not implemented even after
(Example) Case of interlock
start-up of cupfiller.
Case of interlock
Non-interlock (individual) Interlock
Flushout of the cuspidor bowl is implemented simultaneously
with start-up of cupfiller.
min. sec.
[Procedure for setup]
1. Press the function switch nine times.
2. Press the desired setup switch.
Non-interlock --- switch
Interlock --------- switch

2-18. Setup of micromotor preset mode Ｅ Ａ

The micromotor preset mode causes the micromotor to run at a
preset rotation regardless of the foot controller pedal depressing
extent.
The micromotor preset mode permits memory setup of SET1 to
SET3. Preset revolution (SET1)

[Procedure for setup]

1. Pick up a micromotor from the holder. No.1　SET1
2. For memory setup of preset mode SET1, press rotation mode 10000rpm
select switch until SET1 is displayed on the indicator. Revolution (rpm) of
preset revolution (SET1)
3. SET1 is displayed on the indicator, and at the same time, the
rotation set in SET1 is displayed.
The micromotor runts at this displayed rotation (value for
reference).
4. To change the rotation, press the switch or switch. For changing
The numerical value displayed on the indicator changes. the revolution

5. To store the rotation after change, press the switch.

The set value before change is restored if the main switch is off
without pressing this switch.
6. Memory setup of each of preset mode SET2 and SET2 can be
implemented by observing the procedure described in step 2 and For storing
subsequent above.

CAUTION
Do not change the rotation while the micromotor is running.

- 28 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

3. Cuspidor unit section

3-1. Operation and functions of control panel section

④ ③ ② ①
4 6 7 8 9

⑥
⑤

Increase Decrease
Ｗ Ａ

⑦ ⑧ ⑨

1 Dental light select switch (optional)

Switch for changing the AL-520 / AL-820S / 900 Dental light (Type 920) lighting mode. Either sensor
mode or manual mode can be selected.

2 Service outlet (air) (optional)

Use this outlet to supply air to external equipment.

3 Service outlet (water)

Use this outlet to supply water to external equipment.

4 Service outlet water flow control

Use this knob to control the water flow rate supplied to outside. The flow rate decreases when the knob is
turned clockwise, and the flow rate increases when the knob is turned counterclockwise.

5 Water heater switch

Switch for turning on/off the cupfiller water heater.
The cupfiller water is heated to warm water when this switch is turned on.

NOTICE: Water drips from the cupfiller nozzle when the water in the water heater
OFF ON is heated. This phenomenon is not a sign of failure.

CAUTION
To prevent damage to the water heater caused by heating without water, ensure that the cup is
filled with water before turning on the water heater switch. The heating element will burn out if
the water heater is switched on without water.

6 Cupfiller control knob

Use this knob for controlling the cupfiller water flow rate. The flow rate decreases when the knob is
turned clockwise, and the flow rate increases when the knob is turned counterclockwise.

- 29 -
 4. DESCRIPTION OF OPERATION AND FUNCTIONS OF COMPONENTS

7 Bowl flush control knob

Use this knob for controlling the bowl flush water flow rate. The flow rate decreases when the knob is
turned clockwise, and the flow rate increases when the knob is turned counterclockwise.

8 Syringe water control

Make adjustment of syringe water by the syringe water control knob (with blue cap). The flow rate
decreases when the knob is turned clockwise, and the flow rate increases when the knob is turned
counterclockwise.

9 Syringe air control

Make adjustment of syringe air by the syringe air control knob (with yellow cap). The flow rate
decreases when the knob is turned clockwise, and the flow rate increases when the knob is turned
counterclockwise.
NOTICE: The water and air flow rate control knobs are provided for increasing/decreasing the
flow rate, and they are not stop valves. Note that the knobs will become idle if they are shut off
too strongly.

3-2. Assistant membrane switch panel

The operation and functions of the assistant membrane switch
panel are the same as those on the membrane switch panel in the
doctor unit section.

3-3. Vacuum handpiece

Suction begins when the vacuum handpiece is taken out of the
holder.
In case of the central vacuum system, suction will not stop
Tip

OPEN
immediately after the vacuum handpiece was returned to the
holder, but suction will continue for about 3 seconds by the CLOSE
function of delay circuit. Valve

Opening or closing the valve can control the suction flow rate.

3-4. Saliva ejector handpiece Saliva ejector nozzle

Suction begins when the saliva ejector handpiece is taken out

of the holder, and suction terminates when the saliva ejector OPEN
handpiece is returned to the holder.
- In case the saliva ejector handpiece is equipped with a valve, CLOSE

opening or closing the valve can control the suction flow rate. Valve

3-5. Cuspidor Rotation

The cuspidor unit turns clockwise by 90 degrees.
The assistant instruments holder further turns clockwise by 45
degrees in addition to 90-degree turn of the cuspidor unit.

- 30 -
 5. CARE AND MAINTANANCE

1. Chair Section
Chair Cleaning
- The surface of the chair’s seating area is made of
synthetic leather. Apply dry wiping or wipe the surface
with cloth moistened with either water or diluted neutral
detergent for the care.
- If the color of clothing or belt remained on the
synthetic leather, wipe it off with cloth moistened with
diluted neutral detergent as soon as possible, to avoid its
penetration caused by plasticizer.
- In case the synthetic leather is wiped with a wet cloth,
fully wipe off the moisture. If it remains, hydrolytic
degradation may be accelerated. Do not use solvent or
bleach.
- Apply dry wiping using a dry and soft cloth to metallic
areas. If any metallic area is wetted, wipe off the
moisture as soon as possible. It will rust otherwise.
- Wipe the resin cover with a wet and soft cloth.

Chair Sterilization
- Use FD333 made by Durr or ethanol as sprayed to a soft
cloth or paper towel for cleaning and sterilization of the
product exterior. Do not operate the product until the
liquid used for sterilization has fully dried up.

CAUTION
Do not place any hard and heavy article or any article having a sharp tip or edge on the chair’s seating
area. The synthetic leather may be damaged otherwise.
For cleaning the resin cover, do not use solvent or detergent containing abrasive agent. In addition, do
not use any chemical that is other than specified for this unit. The resin cover may crack otherwise.
Use a soft cloth moistened with either water or diluted neutral detergent.
Never use detergent of strong acidity or alkali pipe detergent, or materials including metal may be
corroded.

- 31 -
 5. CARE AND MAINTANANCE

2. Doctor unit section

Tray mat (Silicone Mat)

Membrane Panel

MA
IN
LO
CK
LP
0
1
2

A
W
Doctor Instruments holder

Waste receptacle (optional)

When waste accumulates, replace paper cup 1 as required Paper cup type Stainless cup type

from waste receptacle holder 2 .

② B A
Waste receptacle
トレーマット (optional) 3 made of stainless steel is
removed when turned in direction A, and is fastened when
操作パネル
turned in direction B.
Since the cover is provided with sharp edges for easily ③
MA
IN
LO
CK

LP
0
1
2

catching cotton or the like. Therefore, be careful at the

F

①
A
W

occasions of cleaning.
ドクター側ホルダー
汚物入れ
Oil mist separator (optional) オイルミスト
The oil mist separator (optional) collects the oil contained in
セパレーター

the exhaust air from handpieces.

Make sure to discard the oil when the oil level rises to the
red line marked on oil receiver container 1 .
The oil receiver container can be removed when turned ①
counterclockwise.

Tray mat (optional)

The silicone mat (optional) can be disinfected with autoclave
and they also permit sterilization with alcohol.

Doctor Instrument holder

Use cleaning agent FD333 made by Durr.

- 32 -
 5. CARE AND MAINTANANCE

Membrane switch panel

CAUTION
In case the surface of the membrane switch panel is
wiped with disinfectant agent or the like, fully wipe
away the chemical. Membrane switch malfunction
may arise if the chemical penetrates to the back face
of the membrane.

Handpiece hose
Carefully wipe away the filth from the handpiece hose
using soft cloth moistened with alcohol or the like.

NOTICE: Observe instructions given in handpiece

instruction manuals for the care of handpieces.

Type 77, 3-way syringe

The nozzle permits autoclave sterilization (132 deg C, 0.19
B Nozzle
MPa). Loosen the nut by turning it in direction A. The
nozzle can be removed from the syringe.
Remove dirt with tap water before sterilization. Ｗ
Ａ
Apply equal thin coat of vaseline to two O-rings after
sterilization. To return the nozzle to the original position, A
Nut
firmly tighten the nut by turning it in direction B.
Keep the syringe in a clean place.

CAUTION
Assure that the nut is positively tightening before use.

- 33 -
 5. CARE AND MAINTANANCE

3. Cuspidor unit section

Cleaning of solid collector
Remove the filter in the solid collector located in Cap
the cuspidor unit section on termination of medical
treatment, and wash the filter.
The vacuum suction force will drop if excessive solids
Bar
are contained in the solid collector filter.
Filter
For removing the filter, remove the cover and pull the
bar. The filter comes out together with the bar. The
filter can be removed from the bar when the filter is
twisted.

Cleaning of cuspidor section

Waste filter 1 in the cuspidor bowl is easily clogged.
Therefore, clean it daily on termination of medical 1

treatment.

CAUTION
Never use emery paper, metallic brush or detergent containing grinding agent for cleaning.
Use of strong acid detergent or alkali pipe detergent may corrode metals. Never use detergent of
such a nature.

CAUTION
Make sure to turn off the main switch before dismounting or mounting of the cuspidor bowl or
cupfiller tray. If the main switch is not turned off at such an occasion, the cupfiller sensor may be
activated by hand or any other article during mounting/dismounting work, water for bowl flush
may jet out, and corrosion to metallic components may arise.
The cuspidor bowl is made of porcelain, and it may be cracked if impact is applied to it.
Furthermore, cleaning of the cuspidor bowl with hot water should be avoided because cracking
may result.
The cuspidor bowl can be easily removed. Be careful not to apply excessive force at occasions
other than cleaning. (Be careful not to apply impact to it, not to drive it and not to allow it to fall.)

- 34 -
 5. CARE AND MAINTANANCE

Cleaning of vacuum handpiece body section

[Disassembling and cleaning procedure] Cap

1. Pull the cap section and body of the vacuum handpiece

Valve
to outside, and carry out disassembly as shown in the
figure. Also remove the valve from the slide groove. Body
Remove dirt with tap water before sterilization.
2. Remove the filth from the valve and cap section using
Durr FD333.
3. Scrape out the filth from the body's slide groove with a
tooth brush, and wipe it off using Durr FD333. FD333
Apply vaseline to the body's slide groove on termination
of cleaning.
Tooth Brush
4. For reassembly, fit the valve to the body's slide groove,
and then fit the cap section as matched with the shape of
the body.

Vaseline
* The saliva ejector handpiece body also permits
disassembly and cleaning by observing the procedure
described above.

The vacuum tip, saliva ejector nozzle, cap and filter can
Vacuum tip
be sterilized with autoclave. Sterilize the body with (optional) Saliva
ejector
autoclave in the assembled state. nozzle
(optional)
Sterilization with autoclave is permitted up to 250 times.
However, sterilization of the valve with autoclave is Cap Cap

permitted up to 100 times (because of application of load

at the time of sliding).
Keep the vacuum tip and saliva ejector tip in a clean Body

place. Body
Valve
Valve
Saliva
ejector
Vacuum hose
hose
Hose connector

- 35 -
 5. CARE AND MAINTANANCE

Cleaning of vacuum hose and saliva ejector hose

The vacuum hose and saliva ejector hose can be
removed when the joint is unlocked by turning it Release
counterclockwise. Therefore, they can be cleaned with Lock

running water.
For cleaning the vacuum hose and saliva ejector hose,
turn off the main switch for the unit. For fitting the Joint
hose, insert the joint section and then twist it clockwise Saliva ejector hose
Vacuum hose
for locking it.
If the hose can be hardly removed or hardly locked, turn
the hose while forcing it.

- 36 -
 5. CARE AND MAINTANANCE

4. Junction box section

Cleaning of air filter drain valve and water drainage from air compressor
The drain valve is provided for drainage of water from the air filter.
Drain the water accumulated in the air filter by turning the drain valve counterclockwise, at least once
a week.
If water enters the unit interior, failure of air turbine, air motor, syringe and so forth may arise. After
water drainage from the air filter, make sure to close the drain valve by turning it clockwise.
Drain the water accumulated in the air compressor, with the drain valve opened, once a week.

Drain Valve

5. Product exterior section

Cleaning of product exterior
Apply dry wiping to metallic components with soft cloth.
If water was spilled to any component, wipe off the moisture immediately. Corrosion and rusting may
arise otherwise.
Wipe the plastic cover with wet and soft cloth.

Sterilization of product exterior

Use FD333 made by Durr for cleaning and bacteria elimination from the product exterior.

NOTICE: Wipe off water and residual disinfectant immediately. Corrosion and rusting may arise
otherwise.

- 37 -
 6. STORAGE, LIFETIME, DISPODAL AND RESTRICTIONS OF USE

Procedure for storage of the unit

Make sure to carry out works of items described below on termination of medical treatment for the day, or
when it is anticipated that the unit will not be used for a long period of time for recess or the like.
1. Main switch
Make sure to turn off the main switch on termination of medical treatment. (It is for stopping supply of
compressed air, water, electricity and so forth.)
This action is essential for preventing water leakage and electric troubles.
2. Water main valve
Make sure to turn the water main valve to the closed position by turning it counterclockwise, on
termination of medical treatment.
This action is essential for preventing water leakage.
3. Water main valve
Turn the water main valve to the closed position by turning it clockwise if it is anticipated that the unit
will not be used for a long period of time for recess or the like.
4. Air main valve
Turn the air main valve to the closed position by turning it clockwise if it is anticipated that the unit will
not be used for a long period of time for recess or the like.
5. Discharge air from the air compressor after turning off the air compressor circuit breaker. (Make sure to
turn off the power.)
6. Make sure to turn off the vacuum pump circuit breaker. (Make sure to turn off the power.)
7. Make sure to turn off the equipment circuit breaker in the clinic cabinet panel. (Make sure to turn off the
power.)

Lifetime
The lifetime of this product is ten years after production and shipping.

In case of disposal of equipment

In case of disposal of equipment or of components dismounted from the unit, take full infection preventing
measures, and carry out appropriate steps in accordance with the legal regulations at that time.

- 38 -
 7. BEFORE ASKING FOR REPAIRS

If any of phenomena described below has occurred, make the following checks before asking for repairs.

Phenomenon Check point and result Action to be taken

Main switch is not on.

Turn on the main switch.

The product Air compressor power is not on. Turn on the power.
does not
work at all. Equipment circuit breaker in the clinic
cabinet panel is not on. Turn on the equipment circuit breaker.

Locking device for motion stop is activated. Unlock the device. See page .
The chair does
not work.

Water main valve is closed. Open the water main valve.

Water is not Water flow rate control valve or knob for

handpiece or the like is closed. Open the valve or knob.
supplied.

Vacuum pump power is not on. Turn on the power.

Vacuum suction Filter of solid collector is filthy. Clean the filter.

does not work. Clean the filter.
Filter of vacuum handpiece is filthy.

Saliva ejector
Ifhandpiece
the unit does not normally
does Filter ofwork even
saliva if actions
ejector were taken
handpiece upon checkup
is filthy. stated
Clean the filter.above, then stop using the
unit,
not turn
make offsuction.
the main switch and contact your dealer or our office.

- 39 -
 8. DIMENSION AND SPECIFICATION

Specification
Rated power supply ------------------------------------------------- AC.115V 7.7A/6.3A 50/60Hz
AC.220V 3.5A/3.5A 50/60Hz
AC.230V 3.4A 50Hz
AC.240V 3.6A 50Hz
Fuse ------------------------------------------------------------------- 115V F10A 125V
220 - 240V F5A 250V
Air main pressure --------------------------------------------------- 0.45 to 0.5MPa
Water main pressure ------------------------------------------------ 0.1 to 0.2MPa
Mass ------------------------------------------------------------------ Cuspidor unit section : 74kg
Doctor unit section : 40kg
Chair section : 150kg
Dental light ---------------------------------------------------------- AL-720S / AL-520
AL-820S / 900 Dental Light (Type 920)
Working environment ---------------------------------------------- Temperature : 10 to 40 ℃
Humidity : 30 to 75%
Atmospheric pressure : 700 to 1060hPa
Maximum Load ----------------------------------------------------- 135kg

Classification
Operation mode ------------------------------------------------------ Short-time operating equipment (chair)
Classification of foot controller: ----------------------------------- IPX1(applicable standard IEC60529)
Classification of protection against electric shock -------------- Class I equipment, B type mounting section
　　　　　　　　　　　　　　　　　　　　　　　　　( Upholstery and Handpieces )
Equipment that is not suitable for use in air, flammable anesthetic gas, oxygen or nitrous oxide

- 40 -
 8. DIMENSION AND SPECIFICATION
Dimension (Numerical values shown here represent standard values.) Unit: mm
Base mount type Dimensional tolerance: ±10%
1710

594
462
398
460
(1939 for 920 light)

584
Max.2456

188
1871

848

790~900
483~748

822
959

Cart type 1710

594

636

584
(1939 for 920 light)
Max.2456

188
1871

296
848

750~1000

483~748

570

530 822 400

959

- 41 -
 9. MAINTANANCE AND INSPECTION

Guide for daily maintenance and inspection (Maintenance and inspection by user)

Management of maintenance and inspection of medical equipment should be implemented by the user (medical
保 守 点 検
institution). In case the user does not implement such management, it is permitted that such management is
outsourced to a qualified entity such as a medical equipment repair company.
For safe use of this product, it is necessary that inspection should be conducted in the specified frequency on
the items described below.

No. Item Frequency Inspection method Influence if inspection Maintenance required in case
and diagnosis not conducted of nonconformity
１ Check Before ①Chair operation switches Unexpected personal Contact your dealer or our
of safety start shall not work when foot injury and troubles may office if any abnormality arises.
functions controller pedal is arise due to motion of
depressed. the chair during medical
②When cuspidor section is treatment and due to
turned to the patient side, pinching between
cuspidor indicator shall doctor section and
light up in pink, and chair chair.
operation switches shall
not work.
２ Check for Before Leakage of water and air The product will not Contact your dealer or our office
leakage of start shall not be observed normally work, and if any abnormality arises.
water and around the product. troubles may arise.
air
３ Cupfiller Before When a paper cup is placed Cupfilling may not be Execute re-inspection in accor-
start on the cupfiller, the cup executed. dance with "Method for operation"
shall be detected and described in the instruction
cupfilling shall be executed. manual.
* Malfunction may arise if Contact your dealer or our office if
the cup is of another recovery is not achieved as a
material grade (such as result of re-inspection.
stainless steel and plastics)
or if the paper cup is of dark
color or pattern.
４ Check of Before ①Air turbine revolution, Troubles such as injury Control the water flow in accor-
motions of water flow, air flow and so in patient's oral cavity dance with "Control of compo-
start forth shall be free of
equipment and equipment failure nents" described in the instruction
abnormality. may arise. manual. If any other abnormality
②Micromotor revolution, arises, refer to the instruction
water flow and so forth shall
be free of abnormality. manual attached to individual
③Scaler vibration, water equipment.
flow and so forth shall be Contact your dealer or our office if
free of abnormality. recovery is not achieved.

５ Check of For each Appropriate bar shall be The bar will not normally If abnormality such as flaw and
air turbine patient positively mounted. work and troubles may deformation is found on the bar,
bar Make sure to refer to the arise. replace the bar in accordance with
instruction manual attached the instruction manual attached to
to individual equipment. individual equipment.
６ Check of For each Appropriate tip shall be The tip will not normally If the tip was worn or deformed,
scaler tip patient positively mounted and be work and troubles may replace the tip in accordance with
correctly used. arise. the instruction manual attached to
Make sure to refer to the the scaler.
instruction manual attached Contact your dealer or our office if
to the scaler. any other trouble arises.
７ Check of For each The nut for fixing the nut of Troubles may arise if Turn and positively retighten the
tightness of patient Type 77, 3-way syringe shall the nut comes off. nut that fixes the nozzle.
syringe nut be positively tightened.
８ Matters After Excessive handpiece oil or The motor section will Execute care in accordance with
attached to closing the like shall not be attached not work normally and the instruction manual attached to
micromotor to the motor section. troubles may arise. individual micromotor.

- 42 -
 保 守 点 検
9. MAINTANANCE AND INSPECTION

No. Item Frequency Inspection method Influence if inspection Maintenance required in case
and diagnosis not conducted of nonconformity
9 Care After Flush the suction line, and Faulty suction may Clean the suction line and filter in
Vacuum closing then clean the filter of the arise. accordance with "Method for
and saliva vacuum or saliva ejector care" described in the instruction
ejector handpiece. manual.
handpiece
10 Care After Clean the cuspidor and Faulty water drainage Execute dust removal and
Cuspidor closing dust filter. may arise. cleaning in accordance with
section "Method for care" described in
the instruction manual.
11 Care After Clean the filter of the solid Vacuum suction will Clean the filter in accordance with
Solid closing collector. become weak. "Method for care" described in the
collector instruction manual.
12 Care After Chemical, filthy water and Discoloration and Execute wiping in accordance
Exterior closing so forth shall not be found deterioration to the with "Method for care" described
(attached or remaining) on exterior, and corrosion in the instruction manual.
the product exterior. and rusting to metallic
components may arise.
13 Check of After The product main switch Product failure and Contact your dealer or our office
main switch closing shall be off, and water/air troubles may arise. if the main switch cannot be
and main main valves shall be turned off or if the main valve
valves closed. cannot be closed.

14 Product's Once No abnormal noise or the The product will not Contact your dealer or our office if
moving every like shall be produced from normally work and any abnormality arises.
parts week product's moving parts troubles may arise.
when the product is
operated.
15 Care Water may enter the air Drain the water from Drain the water from the air filter
Drain line, and equipment failure the air filter drain valve. in accordance with "Method for
valve may arise. care" described in the instruction
manual.

16 Check of Check the water pressure The product will not Contact your dealer or our office
water and air pressure by reading normally work, and if the set pressure is abnormally
pressure pressure gauges in the troubles may arise. high or low.
and air cuspidor section.
pressure Basic set pressure :
Water: 0.1 to 0.2 MPa
Air: 0.45 to 0.5 MPa
17 Check of The table shall be free of Injury caused by falling Contact your dealer or our
conditions inclination, and water shall of goods located on the office if any abnormality arises.
of table not flow on the table. table and other troubles
section may arise.

18 Care The oil level in the oil mist Normal output will not be Discharge the oil in accordance
Oil mist separator shall be lower produced due to inferior with "Method for care" described
separator than the red line. handpiece exhaust. in the instruction manual.

- 43 -
NOTE

TAKARA BELMONT CORPORATION

2-1-1, Higashishinsaibashi,Chuo-ku,Osaka, 542-0083, Japan
TEL : 81-6-6213-5945
FAX : 81-6-6212-3680
BOOK NO. 1E00ZXB0
Printed in Japan 2011-09