ENGLISH

YASKAWA AC Drive V1000

Compact Vector Control Drive
Quick Start Guide
Type: CIMR-VC 1
Models: 200 V Class, Three-Phase Input: 0.1 to 18.5 kW
200 V Class, Single-Phase Input: 0.1 to 4.0 kW
400 V Class, Three-Phase Input: 0.2 to 18.5 kW 2
3
To properly use the product, read this manual thoroughly
and retain for easy reference, inspection, and maintenance.
Ensure the end user receives this manual.

4
5
6
7
8

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 1
MANUAL NO. TOEP C710606 15C
2 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
V1000
Quick Start Guide
ENGLISH
1 Safety Instructions and General Warnings . . . . . . . . . . 2
2 Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5 Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Parameter Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 3
1 Safety Instructions and General Warnings

1 Safety Instructions and General Warnings

Yaskawa Electric supplies component parts for use in a wide variety of industrial applica-
tions. The selection and application of Yaskawa products remain the responsibility of the
equipment designer or end user. Yaskawa accepts no responsibility for the way its products
are incorporated into the final system design. Under no circumstances should any Yaskawa
product be incorporated into any product or design as the exclusive or sole safety control.
Without exception, all controls should be designed to detect faults dynamically and fail
safely under all circumstances. All products designed to incorporate a component part man-
ufactured by Yaskawa must be supplied to the end user with appropriate warnings and
instructions as to the safe use and operation of that part. Any warnings provided by Yaskawa
must be promptly provided to the end user. Yaskawa offers an express warranty only as to
the quality of its products in conforming to standards and specifications published in the
manual. NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS OFFERED. Yaskawa
assumes no liability for any personal injury, property damage, losses, or claims arising from
misapplication of its products.

General Warnings
WARNING
• Read and understand this manual before installing, operating or servicing this drive.
• All warnings, cautions, and instructions must be followed.
• All work must be performed by qualified personnel.
• The drive must be installed according to this manual and local codes.
• Heed the safety messages in this manual.
The operating company is responsible for any injuries or equipment damage resulting from
failure to heed the warnings in this manual.

WARNING
Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
The following conventions are used to indicate Safety messages in this manual:

CAUTION
Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.

NOTICE
Indicates a property damage message.

4 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
1 Safety Instructions and General Warnings

Safety Warnings
WARNING
Electrical Shock Hazard
• Do not attempt to modify or alter the drive in any way not explained in this manual.
Failure to comply could result in death or serious injury.
Yaskawa is not responsible for any modification of the product made by the user. This product
must not be modified.
• Do not touch any terminals before the capacitors have fully discharged.
Failure to comply could result in death or serious injury.
Before wiring terminals, disconnect all power to the equipment. The internal capacitor remains
charged even after the power supply is turned off. The charge indicator LED will extinguish
when the DC bus voltage is below 50 Vdc. To prevent electric shock, wait at least five minutes
after all indicators are off and measure the DC bus voltage level to confirm safe level.

• Do not allow unqualified personnel to use equipment.

Failure to comply could result in death or serious injury.
Maintenance, inspection, and replacement of parts must be performed only by authorized
personnel familiar with installation, adjustment, and maintenance of AC drives.

• Do not remove covers or touch circuit boards while the power is on.
Failure to comply could result in death or serious injury.

• Always ground the motor-side grounding terminal.

Improper equipment grounding could result in death or serious injury by contacting the motor
case.

• Do not perform work on the drive while wearing loose clothing, jewelry or without eye
protection.
Failure to comply could result in death or serious injury.
Remove all metal objects such as watches and rings, secure loose clothing, and wear eye
protection before beginning work on the drive.
• Never short the output circuits of the drive.
Do not short the output circuits of the drive. Failure to comply could result in death or serious
injury.
Sudden Movement Hazard
• Stay clear of the motor during rotational Auto-Tuning. The motor may start operating
suddenly.
During automatic starting of equipment, the machine may start moving suddenly, which could
result in death or serious injury.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 5
1 Safety Instructions and General Warnings

WARNING
• System may start unexpectedly upon application of power, resulting in death or serious
injury.
Clear all personnel from the drive, motor, and machine area before applying power. Secure
covers, couplings, shaft keys, and machine loads before applying power to the drive.
Fire Hazard
• Do not use an improper voltage source.
Failure to comply could result in death or serious injury by fire.
Verify that the rated voltage of the drive matches the voltage of the incoming power supply
before applying power.
• Do not use improper combustible materials.
Failure to comply could result in death or serious injury by fire.
Attach the drive to metal or other noncombustible material.
• Do not connect AC line power to output terminals U, V, and W.
• Make sure that the power supply lines are connected to main circuit input terminals R/
L1, S/L2, T/L3 (or R/L1 and S/L2 for single-phase drives).
Do not connect the AC power line to the output motor terminals of the drive. Failure to comply
could result in death or serious injury by fire as a result of drive damage from line voltage
application to output terminals.

• Tighten all terminal screws to the specified tightening torque.

Loose electrical connections could result in death or serious injury by fire due to overheating of
electrical connections.

CAUTION
Crush Hazard
• Do not carry the drive by the front cover.
Failure to comply may result in minor or moderate injury from the main body of the drive
falling.
Burn Hazard
• Do not touch the heatsink or braking resistor hardware until a powered-down cooling
period has elapsed.

6 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
1 Safety Instructions and General Warnings

NOTICE
Equipment Hazard
• Observe proper electrostatic discharge procedures (ESD) when handling the drive and
circuit boards.
Failure to comply may result in ESD damage to the drive circuitry.

• Never connect or disconnect the motor from the drive while the drive is outputting voltage.
Improper equipment sequencing could result in damage to the drive.
• Do not perform a withstand voltage test on any part of the drive.
Failure to comply could result in damage to the sensitive devices within the drive.

• Do not operate damaged equipment.

Failure to comply could result in further damage to the equipment.
Do not connect or operate any equipment with visible damage or missing parts.

• Install adequate branch circuit short circuit protection per applicable codes.
Failure to comply could result in damage to the drive.
The drive is suitable for circuits capable of delivering not more than 30,000 RMS symmetrical
Amperes, 240 Vac maximum (200 V Class) and 480 Vac maximum (400V Class).

• Do not use unshielded cable for control wiring.

Failure to comply may cause electrical interference resulting in poor system performance. Use
shielded twisted-pair wires and ground the shield to the ground terminal of the drive.

• Do not allow unqualified personnel to use the product.

Failure to comply could result in damage to the drive or braking circuit.
Carefully review the braking option instruction manual when connecting a braking option to the
drive.

• Do not modify the drive circuitry.

Failure to comply could result in damage to the drive and will void warranty.
Yaskawa is not responsible for modification of the product made by the user. This product must
not be modified.
• Check all the wiring to ensure that all connections are correct after installing the drive and
connecting other devices.
Failure to comply could result in damage to the drive.

• Do not connect unapproved LC or RC interference suppression filters, capacitors, or

overvoltage protection devices to the output of the drive.
Using unapproved filters could result in damage to the drive or motor equipment.

7 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
1 Safety Instructions and General Warnings

Precautions for CE Low Voltage Directive Compliance

This drive has been tested according to European standard EN61800-5-1, and it fully com-
plies with the Low Voltage Directive. The following conditions must be met to maintain
compliance when combining this drive with other devices:
Do not use drives in areas with pollution higher than severity 2 and overvoltage category 3
in accordance with IEC664.
Ground the neutral point of the main power supply for 400 V Class drives.

Precautions for UL/cUL Standards Compliance

This drive is tested in accordance with UL standard UL508C and complies with UL require-
ments. The following conditions must be met to maintain compliance when using this drive
in combination with other equipment:
Do not install the drive to an area greater than pollution severity 2 (UL standard).
Use UL-listed copper wires (rated at 75°C) and closed-loop connectors or CSA-certified
ring connectors. For details refer to the Technical Manual.
Wire low voltage wires with NEC Class 1 circuit conductors. Refer to national state or local
codes for wiring. Use a class 2 (UL regulations) power supply for the control circuit termi-
nal. For details refer to the Technical Manual.
This drive has undergone the UL short-circuit test, which certifies that during a short circuit
in the power supply the current flow will not rise above 30,000 amps maximum at 240 V for
200 V class drives and 480 V for 400 V class drives.
The drive internal motor overload protection is UL listed and in accordance with the NEC
and CEC. The setup can be done using the parameters L1-01/02. For details refer to the
Technical Manual.

Precautions for Using the Safe Disable Function

The drive’s Safe Disable function is designed in accordance with the EN954-1, safety cate-
gory 3 and EN61508, SIL2. It can be utilized to perform a safe stop as defined by the
EN60204-1, stop category 0 (uncontrolled stop by removal of power). Refer to the Technical
Manual for details about the application of this function.

8 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 2 Mechanical Installation

ENGLISH
2 Mechanical Installation
Upon Receipt
Please perform the following tasks after receiving the drive:
• Inspect the drive for damage. If the drive appears damaged upon receipt, contact your sup-
plier.
• Verify receipt of the correct model by checking the information on the nameplate. If you
have received the wrong model contact your supplier.

Installation Environment
For optimum performance life of the drive, install the drive in an environment that meets the
conditions listed below.
Environment Conditions
Installation Area Indoors
-10°C to +40°C (NEMA Type 1)
-10°C to +50°C (Open-Chassis Type)
Ambient Temperature When using an enclosure panel, install a cooling fan or air conditioner in the
area to ensure that the air temperature inside the enclosure does not exceed the
specified levels.
Do not allow ice to develop on the drive.
Humidity 95% RH or less and free of condensation
Storage Temperature -20°C to +60°C
Install the drive in an area free from:
• oil mist and dust
• metal shavings, oil, water or other foreign materials
• radioactive materials
Surrounding Area • combustible materials (e.g., wood)
• harmful gases and liquids
• excessive vibration
• chlorides
• direct sunlight
Altitude 1000 m or less
Vibration 10 - 20 Hz at 9.8 m/s2, 20 - 55 Hz at 5.9 m/s2
Orientation Install the drive vertically to maintain maximum cooling effects.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 9
2 Mechanical Installation

Installation Orientation and Spacing

Always install the drive in an upright position. 30mm 30mm
100mm Air
Leave space around the unit for proper cooling
as shown in the figure on the right.
Note: Several units can be installed closer
together than shown in the figure by
using “Side-by-Side” mounting. For
details please refer to the Technical
Manual.
100mm Air

Dimensions
d W1
H2

Model Dimensions (mm) Weight

CIMR-VC Fig. W H D W1 H1 H2 H3 H4 D1 d (kg)
BA0001B 68 128 76 56 118 5 - - 6.5 M4 0.6
H1
H

BA0002B 68 128 76 56 118 5 - - 6.5 M4 0.6

BA0003B 68 128 118 56 118 5 - - 38.5 M4 1.0
A
W BA0006B 108 128 137.5 96 118 5 - - 58 M4 1.7
IP20 / Open
Chassis BA0010B 108 128 154 96 118 5 - - 58 M4 1.8
BA0012B 140 128 163 128 118 5 - - 65 M4 2.4
BA0018B 170 128 180 158 118 5 - - 65 M4 3.0
A
2A0001B 68 128 76 56 118 5 - - 6.5 M4 0.6
2A0002B 68 128 76 56 118 5 - - 6.5 M4 0.6
D D1 2A0004B 68 128 108 56 118 5 - - 38.5 M4 0.9
d 2A0006B 68 128 128 56 118 5 - - 38.5 M4 1.1
H3

H2

W1
2A0010B 108 128 129 96 118 5 - - 58 M4 1.7
2A0012B 108 128 137.5 96 118 5 - - 58 M4 1.7
2A0020B 140 128 143 128 118 5 - - 65 M4 2.4
2A0030F 140 254 140 122 248 6 13 6.2 55 M5 3.8
H1
H

2A0040F 140 254 140 122 248 6 13 6.2 55 M5 3.8

B
2A0056F 180 290 163 160 284 8 15 6.2 75 M5 5.5
2A0069B 220 350 187 192 336 7 15 7.2 78 M6 9.2
4A0001B 108 128 81 96 118 5 - - 10 M4 1.0
B
H4

W 4A0002B 108 128 99 96 118 5 - - 28 M4 1.2

IP20 / NEMA 4A0004B 108 128 137.5 96 118 5 - - 58 M4 1.7
Type 1 4A0005B A 108 128 154 96 118 5 - - 58 M4 1.7
4A0007B 108 128 154 96 118 5 - - 58 M4 1.7
4A0009B 108 128 154 96 118 5 - - 58 M4 1.7
4A0011B 140 128 143 128 118 5 - - 65 M4 2.4
4A0018F 140 254 140 122 248 6 13 6 55 M5 3.8
4A0023F 140 254 140 122 248 6 13 6.2 55 M5 3.8
B
D1
4A0031F 180 290 143 160 284 8 15 6 55 M5 5.2
D 4A0038F 180 290 163 160 284 8 15 6 75 M5 5.5

10 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
2 Mechanical Installation

d
W1
Model Dimensions (mm) Weight
H3

H2
CIMR-VC Fig. W H D W1 H1 H2 H3 H5 D1 d (kg)
2A0030A 140 247 140 122 248 6 13 13 55 M5 3.6
2A0040A 140 247 140 122 248 6 13 13 55 M5 3.6
2A0056A 180 285 163 160 284 8 15 15 75 M5 5.3
2A0069A 220 335 187 192 336 7 15 15 78 M6 8.7
H1
H

C
4A0018A 140 247 140 122 248 6 13 13 55 M5 3.6
4A0023A 140 247 140 122 248 6 13 13 55 M5 3.6
H5

4A0031A 180 285 143 160 284 8 15 15 55 M5 5.0

C W 4A0038A 180 285 163 160 284 8 15 15 75 M5 5.3
IP00 / Open
Chassis

D1
D

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 11
3 Electrical Installation

3 Electrical Installation
The figure below shows the main and control circuit wiring.
DC reactor Thermal Braking
(option) relay resistor
(opt)
Link

+2 +1 㪄 B1 B2
Fuses U
L1 R/L1 U/T1
Power V
Supply
L2 Filter S/L2 V1000 V/T2 M
T/L3 <1> W
L3 W/T3
Main
Switch Forward/Stop S1
Shielded
Cable
Reverse/Stop S2
Ground
External Fault S3

Fault Reset S4

Multi-speed 1 S5

Multi-speed 2 S6
+24 V 8 mA
MA Multi-function relay output
MB Fault 250 Vac / 30 Vdc (10 mA to 1A)
Multi-function 24 V (default setting)
digital inputs MC
(default setting) SINK
DIP
switch S3 SOURCE
SC
P1
During run
0V
Multi-function photo-
coupler output
Shielded ground P2 48 Vdc, 2 to 50 mA
terminal Frequency agree
Photocoupler (default setting)
PC
Pulse Input common
RP (max. 32kHz)
MP Pulse train output
+V Analog input power supply
2 kΩ +10.5 Vdc, max. 20 mA (max. 32 kHz)
A1 Multi-function analog input 1 (Output frequency)
0 to 10 V (20 kΩ) Monitor outputs
A2 Multi-function analog input 2 AM (default setting)
0 to 10 V (20 kΩ) or
Analog output
AC 0/4 to 20 mA (250 Ω) 0 to +10 Vdc (2mA)
AC (Output frequency)

Multi- function pulse / analog inputs

(default: frequency reference) Terminal resistance
(120 Ω, 1/2 W)
R+

H2 R−
Safe Disable Memobus comm.
inputs S+ RS-485/422
H1 max. 115 kBps
S−
HC IG

Symbols:
Use twisted pair cables. Indicates a main circuit terminal.

Use shielded twisted pair cables. Indicates a control circuit terminal.

<1> Single-phase units do not have a T/L3 terminal.

12 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
3 Electrical Installation

Wiring Specification

Main Circuit
Use the fuses and line filters listed up in the table below when wiring the main circuit. Make
sure not to exceed the given tightening torque values.
Recom. Main Circuit Terminal Sizes
Model EMC Filter [Schaffner] Main Fuse
Motor R/L1,S/L2,T/L3, U/
CIMR-VC [Ferraz] cable T1,V/T2,W/T3, - , B1, B2
(mm²) +1, +2
BA0001 TRS5R 2.5 M3.5 M3.5 M3.5
BA0002 FS5855-10-07 TRS10R 2.5 M3.5 M3.5 M3.5
BA0003 TRS20R 2.5 M3.5 M3.5 M3.5
BA0006 TRS35R 2.5 M4 M4 M4
FS5855-20-07
BA0010 TRS50R 4 M4 M4 M4
BA0012 FS5855-30-07 TRS60R 6 M4 M4 M4
BA0018 FS5855-40-07 A6T80 10 M5 M5 M5
2A0001 TRS5R 2.5 M3.5 M3.5 M3.5
2A0002 TRS5R 2.5 M3.5 M3.5 M3.5
FS5856-10-07
2A0004 TRS10R 2.5 M3.5 M3.5 M3.5
2A0006 TRS15R 2.5 M3.5 M3.5 M3.5
2A0010 TRS25R 2.5 M4 M4 M4
FS5856-20-07
2A0012 TRS35R 4 M4 M4 M4
2A0020 FS5856-30-07 TRS60R 6 M4 M4 M4
2A0030 FS5973-35-07 A6T70<1> 10 M4 M4 M5
2A0040 FS5973-60-07 A6T100<1> 16 M4 M4 M5
2A0056 A6T150<1> 25 M6 M5 M6
FS5973-100-07
2A0069 A6T200<1> 35 M8 M5 M6
4A0001 TRS2.5R 2.5 M4 M4 M4
FS5857-5-07
4A0002 TRS5R 2.5 M4 M4 M4
4A0004 TRS10R 2.5 M4 M4 M4
4A0005 TRS20R 2.5 M4 M4 M4
FS5857-10-07
4A0007 TRS20R 2.5 M4 M4 M4
4A0009 TRS20R 2.5 M4 M4 M4
4A0011 FS5857-20-07 TRS30R 2.5 M4 M4 M4
4A0018 A6T50<1> 6 M4 M4 M5
FS5972-35-07
4A0023 A6T60<1> 10 M4 M4 M5
4A0031 A6T70<1> 10 M5 M5 M5
FS5972-60-07
4A0038 A6T80<1> 16 M5 M5 M6
<1> For UL compliance a different fuse type has to be used. For details refer to the Technical Manual.
Tightening Torque Values
Tighten the main circuit terminals using the torque values provided by the table below.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 13
3 Electrical Installation

Terminal Size M3.5 M4 M5 M6 M8

Tightening Torque
0.8 to 1.0 1.2 to 1.5 2.0 to 2.5 4.0 to 5.0 9.0 to 11.0
(N m)

Control Circuit
The control terminal board is equipped with screwless terminals. Always use wires within
the specification listed below. For safe wiring it is recommended to use solid wires or flexi-
ble wires with ferrules. The stripping length respectively ferrule length should be 8 mm.
Wire Type Wire size (mm2)
Solid 0.2 to 1.5
Flexible 0.2 to 1.0
Flexible with ferrule 0.25 to 0.5

EMC Filter Installation

This drive has been tested in accordance with European standards EN61800-3. In order to
comply to the EMC standards, wire the main circuit as described below.
1. Install an appropriate EMC noise filter to the input side.See the list above or refer to the
Technical Manual for details.
2. Place the drive and EMC noise filter in the same enclosure.
3. Use braided shield cable for the drive and motor wiring
4. Remove any paint or dirt from ground connections for minimal ground impedance
5. Install an AC reactor at drives smaller than 1 kW for compliance with the
EN61000-3-2. Refer to the Technical Manual or contact your supplier for details
N
L1 L2
PE L3 L1 PE

Panel or mounting wall Panel or mounting wall

Metal plate Metal plate
Grounding Surface Grounding Surface
(remove any paint) (remove any paint)

E E
N L1

L3 L2 L1

EMC EMC
Filter Drive Drive
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 Filter R/L1 S/L2 T/L3 U/T1 V/T2 W/T3

Grounding Grounding
Surface Surface
(remove any (remove any
paint) paint)
Wiring distance as Wiring distance as
short as possible short as possible

Cable shield Braid shielded motor Braid shielded motor

Cable shield
grounding clamp cable grounding clamp cable
Ground shield at
Ground shield at
motor side
motor side
M M

EMC Standards Compliant Wiring of Single and Three Phase Units

14 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
3 Electrical Installation

Main and Control Circuit Wiring

Wiring the Main Circuit Input

Consider the following precautions for the main circuit input.
• Use fuses recommended in Main Circuit on page 11 only.
• If using a ground fault circuit breaker, make sure that it can detect both DC and high fre-
quency current.
• If using an input switch is used, make sure that the switch does not operate not more than
once every 30 minutes.
• Use a DC reactor or AC reactor on the input side of the drive:
–To suppress harmonic current.
–To improve the power factor on the power supply side.
–When using an advancing capacitor switch.
–With a large capacity power supply transistor (over 600 kVA).

Wiring the Main Circuit Output

Consider the following precautions for the output circuit wiring.
• Do not connect any other load than a 3 phase motor to the drives output.
• Never connect a power source to the drives output.
• Never short or ground the output terminals.
• Do not use phase correction capacitors.
• If using a contactor between the drive and motor, it should never be operated when the
drive is outputting a voltage. Operating while there is voltage output can cause large peak
currents, thus tripping the over current detection or damage the drive.

Ground Connection
Take the following precautions when grounding the drive.
• Never share the ground wire with other devices such as welding machines, etc.
• Always use a ground wire, that complies with electrical equipment technical standards.
Keep ground wires as short as possible. Leakage current is caused by the drive. Therefore,
if the distance between the ground electrode and the ground terminal is too long, potential
on the ground terminal of the drive will become unstable.
• When using more than one drive, do not to loop the ground wire.

Control Circuit Wiring Precautions

Consider the following precautions for wiring the control circuits.
• Separate control circuit wiring from main circuit wiring and other high-power lines.
• Separate wiring for control circuit terminals MA, MB, MC (contact output) from wiring
to other control circuit terminals.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 15
3 Electrical Installation

• For external control power supply use a UL Listed Class 2 power supply.
• Use twisted-pair or shielded twisted-pair cables for control circuits to prevent operating
faults.
• Ground the cable shields with the maximum contact area of the shield and ground.
• Cable shields should be grounded on both cable ends.
• If flexible wires with ferrules are connected they might fit tightly into the terminals. To
disconnect them, grasp the wire end with a pair of pliers, release the terminal using a
straight-edge screw driver, turn the wire for about 45°, and pull it gently out of the termi-
nal. For details, refer to the Technical Manual. Use this procedure for removing the wire
link between HC, H1 and H2 when the Safe Disable function is utilized.

Main Circuit Terminals

Terminal Type Function
Main circuit power Connects line power to the drive.
R/L1, S/L2, T/L3
supply input Drives with single-phase 200 V input power have no T/L3 terminal.
U/T1, V/T2, W/T3 Drive output Connects to the motor.
B1, B2 Braking resistor For connecting a braking resistor or the braking resistor unit option.
DC reactor connec-
+1, +2 Linked at shipment. Remove the link to install a DC choke.
tion
DC power supply
+1, – For connecting a DC power supply.
input
For 200 V class: Ground with 100 Ω or less
Ground Terminal
(2 terminals) For 400 V class: Ground with 10 Ω or less

Control Circuit Terminals

The figure below shows the control circuit terminal arrangement. The drive is equipped with
screwless terminals.

S2 S1

R+ R- S+ S- IG S3

P1 P2 PC A1 A2 +V AC AM AC MP

Use a straght-edge screwdriver

S1 S2 S3 S4 S5 S6 SC HC H1 H2 RP MA MB MC with a blade width of max 2.5 mm
and a thickness of max 0.6 mm to
release the terminals

There are three DIP switches, S1 to S3, located on the terminal board

16 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
3 Electrical Installation

SW1 Switches analog input A2 between voltage and current input

SW2 Enables or disables the internal RS422/485 comm. port terminal resistance.
Used to select sourcing (PNP)/sinking (NPN, default) mode for the digital inputs (PNP requires
SW3
external 24 Vdc power supply)

Control Circuit Terminal Functions

Type No. Terminal Name (Signal) Function (Signal Level), Default Setting
Photocoupler inputs, 24 Vdc, 8 mA
Multi- S1
Note: Drive preset to sinking mode (NPN). When using
Function to Multi-function digital input 1 to 6
source mode, set DIP switch S3 to “SOURCE” and use an
Digital S6
external 24 Vdc (±10%) power supply.
Inputs
SC Multi-function input common Sequence common
Response frequency: 0.5 to 32 kHz, Duty: 30 to 70%, High:
Multi- RP Pulse train input
3.5 to 13.2 V, Low: 0.0 to 0.8 V, input impedance: 3 kΩ)
Function +V Analog input power supply +10.5 V (max allowable current 20 mA)
Analog/
A1 Multi-function analog input 1 0 to +10 Vdc (20 kΩ) resolution 1/1000
Pulse
Inputs A2 Multi-function analog input 2 0/4 to 20 mA (250 Ω) resolution: 1/500 (A2 only)
AC Frequency reference common 0V
HC Safe Disable Input common +24 V (max 10 mA allowed)
Safe
Disable H1 Safe Disable Input 1 One or both open: Drive output disabled (time from input
Inputs open to drive output switch off is less than 1 ms)
H2 Safe Disable Input 2 Both Closed: Normal operation
Multi- MA N.O. (fault)
Digital relay output
Function MB N.C. output (fault) 30 Vdc, 10 mA to 1 A
Relay
MC Digital output common 250 Vac, 10 mA to 1 A
Output
Multi- P1 Photocoupler output 1
Function P2 Photocoupler output 2 Digital photocoupler output
PHC 48 Vdc, 2 to 50 mA
Output PC Photocoupler output common
MP Pulse train output 32 kHz (max)
Monitor
AM Analog monitor output 0 to 10 Vdc (2 mA or less), Resolution: 1/1000 (10 bit)
Output
AC Monitor common 0V
MEMO- R+ Communications input (+)
BUS/ R– Communications input (–) MEMOBUS/Modbus communication.:
Commu- S+ Communications output (+) RS-485 or RS-422, 115.2 kbps (max)
nication S- Communications output (–)
NOTICE! The terminals HC, H1, H2 are used for the Safe Disable function which cuts the
output voltage in less than 1 ms if at least one of the inputs H1 or H2 is opened. It is
designed in accordance with the EN954-1, safety category 3 and EN61508, SIL2. It
and can be utilized to perform a safe stop as defined by the EN60204-1, stop
category 0. Do not remove the wire link between HC, H1, or H2 unless the Safe
Disable function is used. Refer to the Technical Manual when using this function.
NOTICE! The wiring length to the terminals HC, H1 and H2 should not exceed 30 m.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 17
4 Keypad Operation

4 Keypad Operation
LED Operator and Keys
The LED operator is used to program the drive, to start/
stop it, and to display fault information. The LEDs indi-
cate the drive status.

STOP

Keys and Functions

Display Name Function
Data Display Area Displays the frequency reference, parameter number, etc.

ESC Key Returns to the previous menu.

Moves the cursor to the right.
RESET Key
Resets a fault.
Starts the drive in the LOCAL mode. The Run LED
• is on, when the drive is operating the motor.
RUN RUN Key • flashes during deceleration to stop or when the frequency reference is 0.
• flashes quickly the drive is disabled by a DI, the drive was stopped using a fast
stop DI or a run command was active during power up.
Up Arrow Key Scrolls up to select parameter numbers, setting values, etc.

Down Arrow Key Scrolls down to select parameter numbers, setting values, etc.

STOP STOP Key Stops the drive.

ENTER Key Selects modes, parameters and is used to store settings.

Switches drive control between the operator (LOCAL) and the control circuit
LO/RE Selection
terminals (REMOTE). The LED is on when the drive is in the LOCAL mode
Key
(operation from keypad).
Flashing: The drive is in an alarm state.
ALM ALM LED Light
On: The drive is in a fault state and the output is stopped.
On: The motor rotation direction is reverse.
REV REV LED Light
Off: The motor rotation direction is forward.
On: The drive is ready to operate the motor.
DRV DRV LED Light
Off: The drive is in the Verify, Setup, Parameter Setting or Auto tuning mode.
On: The output frequency is displayed on the data screen.
FOUT FOUT LED Light
Off: Anything else than the output frequency is displayed on the data screen.

18 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
4 Keypad Operation

Menu Structure and Modes

The following illustration explains the operator keypad menu structure.

Key operation description

:
Turn the power on (DRV lights)
A Run command will start the motor.

Forward Selection Reverse Selection

:
DRV LED is on.

:
Output Frequency

Output Current

Output Voltage

XX The Monitor Displays are used to

Monitor Display read out drive data like terminal
status, output frequency, fault
XX information etc.

XX XX XX
The Verify Menu lists up all
Verify Menu
parameters which are unequal to
XX XX XX the default setting.
The motor can not be started.

XX The Setup Mode can be used to

DRV LED is off.

Setup Mode set up a minimum list of

parameters necessary to run the
XX application.

XX
Parameter Setting Mode
In the Parameter Setting Mode all
drive parameters can be set up.
XX

Auto-Tuning measures the motor

data for optimal performance of
Auto-Tuning
the drive/motor combination.
XX

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 19
5 Start Up

5 Start Up
Drive Setup Procedure
The illustration below shows the basic setup procedure. Each step is explained more detailed
on the following pages.

START

Install and wire the drive as explained.

Turn the power on.

Initialize the drive if necessary using parameter A1-01.

Set the control mode.

Select Normal / Heavy Duty

Perform Auto-Tuning or set the motor data manually.

Set/check the basic parameters:

* b1-01, b1-02 for frequency reference and RUN command source
* H1-xx, H2-xx, H3-xx, H4-xx, H6-xx to configure the I/Os
* Frequency reference values
* C1-xx, C2-xx for Acceleration/Deceleration times and S-curves

Run the motor without load, check the operation and verify, if the
upper controller (e.g. PLC,...) commands to the drive work as
desired.

Connect the load, run the motor and check the operation

Fine tune and set application parameters (e.g. PID,...) if necessary.

Final check the operation and verify the settings.

Drive is ready to run the application

20 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
5 Start Up

Power On
Before turning on the power supply,
• Make sure all wires are connected properly.
• Make sure no screws, loose wire ends or tools are left in the drive.
• After turning the power on, the drive mode display should appear and no fault or alarm
should be displayed.

Control Mode Selection (A1-02)

There are three control modes available. Select the control mode that best suits the applica-
tion the drive will control.
Control Mode Parameter Main Applications
• General variable speed applications, particularly useful for running multi-
A1-02 = 0
V/f Control ple motors from a single drive
(default)
• When replacing a drive in which parameter settings are unknown
Open Loop • General variable speed applications
A1-02 = 2
Vector Control (OLV) • Applications requiring high precision, high speed control
PM Open Loop • Derated torque-load applications employing permanent magnet motors
A1-02 = 5
Vector Control (SPM, IPM) and energy savings.

Normal / Heavy Duty Selection (C6-01)

The drive supports two ratings, Normal Duty and Heavy Duty. Both have different output
current ratings (refer to the catalog or Technical Manual). Set the Duty mode in accordance
with the application.
Mode Heavy Duty Rating (HD) Normal Duty Rating (ND)
C6-01 0 1
Applications with a constant torque like Applications where the torque increases with
Application extruders, conveyors and cranes. High the speed like fans or pumps. High overload
overload capability might be needed. tolerance is normally not needed.
Overload capability (OL2) 150% of drive rated current for 60 s 120% of drive rated current for 60 s
L3-02 Stall Prevention dur-
150% 120%
ing Acceleration
L3-06 Stall Prevention dur-
150% 120%
ing Run
Default carrier frequency 8 kHz Swing PWM

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 21
5 Start Up

Auto-Tuning (T1- )
Auto-Tuning automatically sets up the motor data relevant drive parameters. Three different
modes are supported

Tuning Mode Parameter Control Description

Mode
Perform when setting the drive to operate in Open Loop
Rotational Vector control. The motor must be able to rotate without
T1-01 = 0 OLV
Auto-Tuning load during the tuning process in order to achieve a high
accuracy.
Terminal resistance OLV, V/f Perform in V/f control if the motor cable is long or if the
T1-01 = 2
tuning control cable has been changed.
Rotational Perform when using Energy Saving or Speed Search.The
Auto-Tuning T1-01 = 3 V/f control motor must be able to rotate without load in order to achieve
for Energy Saving a high tuning accuracy.

CAUTION
Never touch the motor until the Auto-Tuning is finished. Even thought the motor may not be
rotating when Auto-Tuning, voltage is still applied to the motor during the tuning process.
For Auto-Tuning enter the Auto-Tuning menu and perform the steps shown in the figure
below. The number of name plate data to be entered depends on the selected type of Auto-
Tuning. This example shows Rotational Auto-Tuning.
Drive mode Enter the Auto- Select the tuning
display Tuning Mode method

Set up all name The tuning start During the tuning the After successful tuning
plate data display appears display flashes “End” is displayed

If Auto-Tuning can not be performed for some reason (no-load operation impossible etc.),
then set up the maximum frequency and voltage in the E1- parameters and enter the
motor data manually into the E2- parameters.

NOTICE! The Safe Disable inputs must be closed during Auto-Tuning.

22 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
5 Start Up

Reference and Run Source

The drive has a LOCAL and a REMOTE mode.
Status Description
LOCAL The Run/ Stop command and the frequency reference are entered at the operator keypad.
The Run command source entered in parameter b1-02 and the frequency reference
REMOTE
source entered in parameter b1-01 are used.
If the drive is operated in the REMOTE mode, make sure that the correct sources for the fre-
quency reference and run command are set in parameters b1-01/02 and that the drive is in
the REMOTE mode.
The LED in the LO/RE key indicates where the Run command is input from.
LO/RE LED Description
ON Run command is issued from operator.
OFF Run command is issued from a different source than the operator.

I/O Setup

Multi-Function Digital Inputs (H1- )

The function of each digital input can be assigned in the H1- parameters. The default set-
ting functions can be seen in the connection diagram on page 10.

Multi-Function Digital Outputs (H2- )

The function of each digital output can be assigned in the H2- parameters. The default
setting functions can be seen in the connection diagram on page 10. The setting value of
these parameters consist of 3 digits, where the middle and right digit set the function and the
left digit sets the output characteristics (0: Output as selected; 1: Inverse output).

Multi-Function Analog Inputs (H3- )

The function of each analog input can be assigned in the H3- parameters. The default
setting of both inputs is “Frequency bias”. Input A1 is set for 0 to 10V input and A2 is set for
4-20 mA input. The addition of both input values builds the frequency reference.
NOTICE! If the input signal level of input A2 is switched between voltage and current, make
sure that DIP switch S1 is in the correct position and parameter H3-09 is set up
correctly.

Monitor Output (H4- )

Use the H4- parameters to set up the output value of the analog monitor output and to
adjust the output voltage levels. The default monitor value setting is “Output frequency”.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 23
5 Start Up

Frequency Reference and Acceleration/ Deceleration Times

Frequency Reference Setup(b1-01)

Set parameter b1-01 according to the frequency reference used.
b1-01 Reference source Frequency reference input
Set the frequency references in the d1- parameters and used digital inputs to
0 Operator keypad
switch over between different reference values.
1 Analog input Apply the frequency reference signal to terminal A1 or A2.
2 Serial Comm. Serial Communications using the RS422/485 port
3 Option Board Communications option card
4 Pulse input Set the frequency reference at terminal RP using a pulse train signal.

Acceleration/ Deceleration Times and S-Curves

There are four sets of acceleration and deceleration times which can be set in the C1-
parameters. The default activated accel/decel times are C1-01/02. Adjust these times to the
appropriate values required by the application. If necessary S-curves can be activated in the
C2- parameters for softer accel/decel start and end.

Test Run
Perform the following steps to start up the machine after all parameter settings have been
done.
1. Run the motor without load and check if all input, outputs and the sequence work as
desired.
2. Connect the load to the motor.
3. Run the motor with load and make sure that there is no vibrations, hunting or motor
stalling occurs.
After taking the steps listed above, the drive should be ready to run the application and per-
form the basic functions. For special setups like PID control etc. refer to the Technical Man-
ual.

24 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
6 Parameter Table

6 Parameter Table
This parameter table shows the most impor- Par. Name Description
tant parameters. Default settings are bold Selects the stopping method when
type. Refer to the Technical Manual for a the run command is removed.
complete list of parameters. Stopping
0:Ramp to Stop
1:Coast to Stop
b1-03 Method
Par. Name Description 2:DC Injection Braking to Stop
Selection
3:Coast with Timer (a new run
Initialization Parameters command is ignored if received
Selects which parameters are before the timer expires)
Access accessible via the digital operator. Reverse
A1-01 Level 0:Operation only 0:Reverse enabled
b1-04 Operation
Selection 1:User Parameters 1:Reverse prohibited
Selection
2:Advanced Access Level
Switches the output phase order.
Selects the Control Method of the Phase Order
b1-14 0:Standard
drive. Selection
Control 1:Switch phase order
0: V/f Control
A1-02 Method DC Injection Braking
2: Open Loop Vector (OLV)
Selection
5: PM Open Loop Vector (PM) DC Sets the frequency at which DC
Note: Not initialized with A1-03! Injection Injection Braking starts when
Resets all parameters to default. b2-01 Braking Ramp to Stop (b1-03 = 0) is
(returns to 0 after initialization) Start selected. If b2-01< E1-09, DC
0:No Initialize Frequency Injection Braking starts at E1-09.
1110: User Initialize (The user Sets the DC Injection Braking cur-
Initialize DC
A1-03 must first set user parameter values rent as a percentage of the drive
Parameters Injection
and then store them using parame- b2-02 rated current.
ter o2-03) Braking
In OLV the DC excitation current is
2220: 2-Wire Initialization Current
determined by E2-03.
3330: 3-Wire Initialization
DC Inj.
Operation Mode Selection Braking
Sets the time of DC Injection Brak-
0:Operator - d1- values Time/DC
b2-03 ing at start in units of 0.01 seconds.
Frequency 1:Analog input A1 or A2 Excitation
Disabled when set to 0.00 seconds.
b1-01 Reference 2:Serial Com - RS-422/485 Time at
Selection 3:Option board Start
4:Pulse Input (Terminal RP) DC Inj.
Sets the DC Injection Braking time
0:Operator - RUN and STOP keys Braking
Run b2-04 at stop. Disabled when set to 0.00
1:Terminals - Digital Inputs Time at
b1-02 Command seconds.
2:Serial Com - RS-422/485 Stop
Selection
3:Option board connected Acceleration/ Deceleration
Accel Sets the acceleration time 1 from 0
C1-01
Time 1 to the max. output frequency.
Decel Sets the deceleration time 1 from
C1-02
Time 1 the max. output frequency to 0.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 25
6 Parameter Table

Par. Name Description Par. Name Description

C1-03 V/f Pattern
Accel/Decel Set the accel/decel times 2 to 4 (set
to Input
Times 2 to 4 like C1-01/02).
C1-08 E1-01 Voltage Input Voltage
C2-01 S-Curve 1 S-curve at acceleration start. Setting
C2-02 S-Curve 2 S-curve at acceleration end. Max. Output For a linear V/f characteristics, set
E1-04
Freq. the same values for E1-07 and E1-
C2-03 S-Curve 3 S-curve at deceleration start.
09. In this case, the setting for E1-
C2-04 S-Curve 4 S-curve at deceleration end. Max. Output
E1-05 08 will be disregarded.
Voltage
Slip Compensation Ensure that the four frequencies are
• Increase if the speed is lower than Base set according to these rules or
Slip Com- E1-06 OPE10 fault will occur:
the frequency reference. Frequency
C3-01 pensation
• Decrease if the speed is higher
Gain Middle Out- E1-04 ≥ E1-06 ≥ E1-07 ≥ E1-09
than the frequency reference. E1-07
put Freq. Output voltage
• Decrease the setting when the slip (E1-05)
Slip Com- Mid. Output
compensation is too slow. E1-08 (E1-13)
C3-02 pensation Voltage
• Increase the setting when the
Delay Time
speed is not stable.
Min. Output
Torque Compensation E1-09
Freq. (E1-08)

• Increase this setting when the

Torque Com- Min. Output
torque response is slow. E1-10
C4-01 pensation Voltage (E1-10)
• Decrease this setting when speed/
Gain
torque oscillations occur. Base (E1-09) (E1-07) (E1-06) (E1-04)
E1-13 Output frequency
• Increase this setting when speed / Voltage
Torque Com-
torque oscillations occur. Motor Data
C4-02 pensation
• Decrease the setting when the
Delay Time Motor Rated Automatically set during Auto-Tun-
torque response is too slow. E2-01
Current ing.
Duty Mode and Carrier Frequency
Motor rated slip in hertz (Hz).
0: Heavy Duty (HD) Motor Rated
Normal/ E2-02 Automatically set by Rotational
Constant torque applications Slip
C6-01 Heavy Duty Auto-Tuning.
1:Normal Duty (ND)
Selection Motor Magnetizing current in Ampere.
Variable torque application
E2-03 No-Load Automatically set by Rotational
1:2.0 kHz Current Auto-Tuning.
2:5.0 kHz
3:8.0 kHz Number of motor poles.
Carrier E2-04 Motor Poles
4:10.0 kHz Automatically set by Auto-Tuning.
C6-02 Frequency
5:12.5 kHz Motor Line- Sets the phase-to-phase motor
Selection
6:15.0 kHz E2-05 to-Line resistance in ohms.
7 to A: Swing PWM1 to 4 Resistance Automatically set by Auto-Tuning.
F: User defined Sets the voltage drop due to motor
Motor Leak-
Frequency References leakage inductance as a percentage
E2-06 age Induc-
d1-01 Frequency of motor rated voltage.
Set the multi-speed references 1 to tance
to Reference Automatically set by Auto-Tuning.
16.
d1-16 1 to 16
d1-17 Jog Speed Jog speed

26 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
6 Parameter Table

Par. Name Description Par. Name Description

Digital Input Settings Pulse Input Setting (Free. ref. input)
H1-01 DI S1 to S6 RP Input Sets the number of pulses (in Hz)
Selects the function of terminals S1 H6-02
to Function Scaling that is equal to 100% input value.
to S6.
H1-06 Selection Pulse Train Sets the input value in % at pulse
H6-03
Major functions are listed at the end of the table. Input Gain input with H6-02 frequency.
Digital Output Settings Pulse Train Sets the input value in % at 0 Hz
H6-04
DO MA/MB Set the function for the relay output Input Bias pulse input frequency.
H2-01
Function MA-MB-MC. Pulse Output Setting
DO P1 Sets the function for the photocou- Enter value equal to U -
H2-02 MP Monitor
Function pler output P1. H6-06 monitor values. Example: Enter
Sel.
DO P2 Sets the function for the photocou- “102” for U1-02.
H2-03
Function pler output P2. MP Monitor Sets the number of output pulses
H6-07
Major functions are listed at the end of the table. Scaling when the monitor is 100% (in Hz).

Analog Input Setting Motor Overheat Protection

A1 Signal 0:0 to +10 V (neg. input is zeroed) Sets the motor overload protection.
H3-01 Motor Over- 0:Disabled
Level Sel. 1:0 to +10 V (bipolar input)
L1-01 load Prot. 1:Standard fan cooled motor
A1 Sel. 2:Standard blower cooled motor
H3-02 Assign a function to terminal A1.
Function Sel. 3:Vector motor
Sets the input value in % at 10 V Motor Over- Sets the motor overload protection
H3-03 A1 Gain
analog input. L1-02 load Prot. time in min. Normally no change is
Sets the input value in % at 0 V Time necessary.
H3-04 A1 Bias
analog input. Stall Prevention
0:0 to +10 V (neg. input is zeroed) 0:Disabled - Motor accelerates at
A2 Signal
1:0 to +10 V (bipolar input) active acceleration rate and may
H3-09 Level Selec-
2:4 to 20 mA (9 bit input) Stall stall with too heavy load or too
tion
3:0 to 20 mA Prevention short accel time.
A2 L3-01 Selection 1:General Purpose - Hold
H3-10 Assign a function to terminal A2. during acceleration when current is
Function Sel.
Acceleration above L3-02.
Sets the input value in % at
H3-11 A2 Gain 2:Intelligent - Acceleration in the
10 V/20 mA analog input.
shortest possible time.
Sets the input value in % at
H3-12 A2 Bias Stall Prev.
0 V/0 mA/4 mA analog input. Sets the current level for stall pre-
L3-02 Level dur-
Analog Input Setting vention during acceleration.
ing Accel.
AM Enter value equal to U1- 0:Disabled - Deceleration as set.
H4-01 Monitor monitor values. Example: Enter Stall Prev.
OV might occur.
Selection “103” for U1-03. Selection
L3-04 1:General Purpose - Deceleration
during
Sets terminal AM output voltage is hold if DC bus voltage rises
H4-02 AM Gain Decel.
equal to 100% monitor value. high.
Sets terminal AM output voltage 0:Disabled - Motor stall or
H4-02 AM Bias Stall Prev.
equal to 0% monitor value. overload might occur.
L3-05 Selection
1:Decel Time 1 - Reduce speed
during Run
using C1-02.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 27
6 Parameter Table

Par. Name Description Monitor Description

Stall Prev. Sets the current level at which stall Input Terminal Status
L3-06 Level dur- prevention during run starts to
: ON : OFF
ing Run operate.
Reserved 1: Digital input 1
Auto-Tuning (terminal S1 enabled)
0:Rotational Auto-Tuning 1: Digital input 2
Auto-Tun- (terminal S2 enabled)
2: Terminal resistance only 1: Digital input 3
T1-01 ing Mode U1-10
3: Rotational Auto-Tuning for (terminal S3 enabled)
Selection
Energy Saving 1: Digital input 4
(terminal S4 enabled)
T1-02 Rated Power Sets the motor rated power (kW). 1: Digital input 5
(terminal S5 enabled)
Rated
T1-03 Sets the motor rated voltage (V). 1: Digital input6
Voltage (terminal S6 enabled)
Rated
T1-04 Sets the motor rated current (A).
Current Output Terminal Status
Base Sets the motor base frequency
T1-05 : ON : OFF
Frequency (Hz).
Reserved 1: Relay Output
T1-06 Motor Poles Sets the number of motor poles. (terminal MA-MC closed
U1-11 MB-MC open)
T1-07 Base Speed Sets the motor base speed (RPM).
1: Open Collector Output 1
Iron loss for determining the (terminal P1) enabled
Motor Iron
T1-11 Energy Saving coefficient. 1: Open collector Output 2
Loss
If unknown leave it on default. (terminal P2) enabled

Monitor Description Drive Status

U1-01 Frequency Reference (Hz)
U1-02 Output Frequency (Hz) 1: During run
U1-03 Output Current (A) 1: During zero-speed
1: During REV
U1-05 Motor Speed (Hz)
U1-12 1: During fault reset
U1-06 Output Voltage Reference (Vac) signal input
U1-07 DC Bus Voltage (Vdc) 1: During speed agree
U1-08 Output Power (kW) 1: Drive ready
1: During alarm detection
U1-09 Torque Reference (% of motor rated torque)
1: During fault detection

U1-13 Terminal A1 input level

U1-14 Terminal A2 input level
Soft Starter Output (freq after accel/decel
U1-16
ramps)
U1-18 OPE Fault Parameter
U1-24 Pulse Input frequency

28 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
6 Parameter Table

Monitor Description DI/DO

Sel. Description
Fault Trace
Digital Input Function Selections
U2-01 Current Fault
3 Multi-step speed reference 1
U2-02 Previous Fault
4 Multi-step speed reference 2
U2-03 Frequency Reference at Previous Fault
5 Multi-step speed reference 3
U2-04 Output Frequency at Previous Fault
Jog frequency command (higher priority than
U2-05 Output Current at Previous Fault 6
multi-step speed reference)
U2-06 Motor Speed at Previous Fault
7 Accel/decel time selection 1
U2-07 Output Voltage at Previous Fault
F Not used (Set when a terminal is not used)
U2-08 DC Bus Voltage at Previous Fault
14 Fault reset (Reset when turned ON)
U2-09 Output Power at Previous Fault
External fault; Input mode: N.O. contact /
U2-10 Torque Reference at Previous Fault 20 to 2F N.C. contact, Detection mode: Normal/during
U2-11 Input Terminal Status at Previous Fault operation
U2-12 Output Terminal Status at Previous Fault Digital Output Function Selections
U2-13 Drive Operation Status at Previous Fault During Run (ON: run command is ON or volt-
0
age is being output)
U2-14 Cumulative Operation Time at Previous Fault
1 Zero Speed
U2-15 Soft-Starter Speed Reference at Previous Fault
2 Speed Agree
U2-16 Motor q-Axis Current at Previous Fault
6 Drive Ready
U2-17 Motor d-Axis Current at Previous Fault
E Fault
Fault History
F Not used
U3-01
Lists the most recent fault that occurred 10 Minor fault (Alarm) (ON: Alarm displayed)
to
through the fourth most recent fault.
U3-04
U3-05
Accumulated operation time at the most recent
to
fault through the fourth most recent fault.
U3-08
U3-09 to Lists the fifth most recent fault that occurred
U3-14 through the tenth most recent fault.
Accumulated operation time at fifth most
U3-15 to
recent fault through the tenth most recent
U3-20
fault.
* The following faults are not recorded in the error log:
CPF00, 01, 02, 03, UV1, and UV2.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 29
7 Troubleshooting

7 Troubleshooting
General Fault and Alarms
Faults and alarms indicate problems in the drive or in the machine.
An alarm is indicated by a code on the data display and the flashing ALM LED. The drive
output is not necessarily switched off.
A fault is indicated by a code on the data display and the ALM LED is on. The drive output
is always switched off immediately and the motor coast to stop.
To remove an alarm or reset a fault, trace the cause, remove it and reset the drive by pushing
the Reset key on the operator or cycling the power supply.
This lists up the most important alarms and faults only. Please refer to the Technical Manual
for a complete list.
LED Display AL FLT Cause Corrective Action
The software base block function is assigned
Base Block to one of the digital inputs and the input is • Check the digital inputs function selection.
off. The drive does not accept Run com- • Check the upper controller sequence.
mands.
The torque limit was reached during deceler-
ation for longer than 3 sec. when in Open • Check the load.
Control Fault
Loop Vector control • Set the torque limit to the most appropriate
• The load inertia is too big. setting (L7-01 through L7-04).
• The torque limit is too low. • Check the motor parameters.
• The motor parameters are wrong.
Control Circuit
Fault • Cycle the drive power supply.
There is a problem in the drive’s control cir-
• Initialize the drive.
to cuit.
• Replace the drive if the fault occurs again.

Control Circuit • Check if the terminal board is installed

Fault There is no terminal board connected to the properly.
control board. • Uninstall and Reapply the terminal board.
• Change the drive.
Cannot Reset Fault reset was input when a Run command Turn off the Run command and reset the
was active. drive.
Option • Remove the fault cause, reset the fault and
External Fault An external fault was tripped by the upper
restart the drive.
controller via an option card.
• Check the upper controller program.
External Fault A forward and reverse command were input • Check the sequence and make sure that the
simultaneously for longer than 500 ms. This forward and reverse input are not set at the
alarm stops a running motor. same time.

30 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
7 Troubleshooting

LED Display AL FLT Cause Corrective Action

External Faults • An external fault was triggered by an exter- • Find out why the device tripped the EF.
nal device via one of the digital inputs S1 Remove the cause and reset the fault.
to to S6. • Check the functions assigned to the digital
• The digital inputs are set up incorrectly. inputs.
• Ground leakage current has exceeded 50%
• Check the output wiring and the motor for
Ground Fault of the drives rated output current.
short circuits or broken insulation. Replace
• Cable or motor insulation is broken.
any broken parts.
• Excessive stray capacitance at drive out-
• Reduce the carrier frequency.
put.
• Check why the upper controller’s safety
device disabled the drive. Remove the
cause and restart.
Safe Disable Both Safe Disable inputs are open. The drive
• Check the wiring.
output is safely disabled and the motor can
• If the Safe Disable function is not utilized
not be started.
for EN60204-1, stop cat. 0 or for disabling
the drive, the terminals HC, H1, H2 must
be linked.
Drive output is disabled while only one of
the Safe Disable inputs is open. (normally
both input signals H1 and H2 should be • Check the wiring from the upper controller
Safe Disable open) and make sure that both signals are set cor-
Fault • One channel is internally broken and does rectly by the controller.
not switch off, even if the external signal is • If the signals are set correctly and the
removed. alarm does not disappear, replace the drive.
• Only one channel is switched off by the
upper controller.
Output cable is disconnected or the motor
Output Phase • Check the motor wiring.
winding is damaged.
Loss • Make sure all terminal screws in the drive
Loose wires at the drive output.
and motor are properly tightened.
Motor is too small (less than 5% of drive
• Check the motor and drive capacity.
current).
Short circuit or ground fault on the drive out- • Check the output wiring and the motor for
put side short circuits or broken insulation. Replace
Overcurrent The load is too heavy. the broken parts.
The accel./decel. times are too short. • Check the machine for damages (gears,
Wrong motor data or V/f pattern settings. etc.) and repair any broken parts.
A magnetic contactor was switched at the • Check the drive parameter settings.
output. • Check the output contactor sequence.
• Check the surrounding temperature and
Heatsink Surrounding temperature is too high.
install cooling devices if necessary.
Overheat The cooling fan has stopped.
• Check the drive cooling fan.
The heatsink is dirty.
or • Clean the heatsink.
The airflow to the heatsink is restricted.
• Check the airflow around the heatsink.
The motor load is too heavy. • Reduce the motor load.
Motor The motor is operated at low speed with • Use a motor with external cooling and set
Overload heavy load. the correct motor in parameter L1-01
Cycle times of accel./ decel. are too short. • Check the sequence.
Incorrect motor rated current has been set. • Check the rated current setting.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 31
7 Troubleshooting

LED Display AL FLT Cause Corrective Action

• Check the load.
Drive • Make sure that the drive is big enough to
The load is too heavy.
Overload handle the load.
The drive capacity is too small.
• The overload capability is reduced at low
Too much torque at low speed.
speeds. Reduce the load or increase the
drive size.
• Increase the deceleration time.
• Enable stall prevention by parameter
DC bus voltage rose too high. L3-04.
DC The deceleration time is too short. • Make sure the braking resistor and braking
Overvoltage Stall prevention is disabled. chopper are working correctly.
Braking chopper / resistor broken. • Check motor parameter settings and adjust
Unstable motor control in OLV. torque and slip compensation, AFR and
Too high input voltage. hunting prevention as needed.
• Make sure that the power supply voltage
meets the drives specifications.
Input Phase Input voltage drop or phase imbalance. • Check the power supply.
Loss One of the input phase is lost. • Make sure that all cables are properly fixed
Loose wires at the drive input. to the correct terminals.
Braking
Transistor
• Cycle the power supply.
Fault The internal braking transistor is broken.
• Replace the drive if the fault reoccurs.

The voltage in the DC bus fell below the

DC undervoltage detection level (L2-05). • Check the power supply.
Undervoltage The power supply failed or one input phase • Make sure, that the power supply is strong
has been lost. enough.
The power supply is too weak.
Controller • Cycle power to the drive. Check if the fault
Undervoltage The drives controller power supply voltage reoccurs.
is too low. • Replace the drive if the fault continues to
occur.
DC Charge • Cycle power to the drive. Check if the fault
Circuit Fault The charge circuit for the DC bus is broken. reoccurs.
• Replace the drive if the fault reoccurs.

32 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
 ENGLISH
7 Troubleshooting

Operator Programing Errors

An Operator Programming Error (OPE) occurs when an inapplicable parameter is set or an
individual parameter setting is inappropriate. When an OPE error is displayed, press the
ENTER button to display U1-18 (OPE fault constant). This monitor will display the parame-
ter that is causing the OPE error.
LED Operator
Display Cause Corrective Action
oPE01 Drive capacity and value set to o2-04 do not
Correct the value set to o2-04.
match.
oPE02 Parameters were set outside the allowable setting
Set parameters to the proper values.
range.
A contradictory setting is assigned to multi-func-
tion contact inputs H1-01 through to H1-06.
• The same function is assigned to two inputs.
oPE03 (this excludes “External fault” and “Not used”) • Fix any incorrect settings.
• Input functions which require the setting of • Refer to the Technical Manual for more details.
other input functions were set alone.
• Input functions that are not allowed to be used
simultaneously have been set.
• The run command source (b1-02) or frequency
oPE05 reference source (b1-01) is set to 3 but no
• Install the required option board.
option board is installed.
• Correct the values set to b1-01 and b1-02.
• The frequency reference source is set to pulse
input but H6-01 is not 0.
Settings to multi-function analog inputs H3-02
and H3-10 and PID functions conflict.
oPE07 • H3-02 and H3-10 are set to the same value. • Fix any incorrect setting.
(this excludes settings “0” and “F”) • Refer to the Technical Manual for more details.
• PID functions have been assigned to both ana-
log inputs and the pulse input at the same time.
oPE08 A function has been set that cannot be used in the
• Fix any incorrect setting.
control mode selected.(might appear after control
• Refer to the Technical Manual for more details.
mode change)
oPE10 • Check the V/f pattern settings.
The V/f pattern setting is incorrect.
• Refer to the Technical Manual for more details.

YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide 33
7 Troubleshooting

Auto-Tuning Errors
LED Operator
Display Cause Corrective Action

Er-01 Motor data fault

The input motor data are not valid. (e.g. the base Re-enter the data and repeat Auto-Tuning.
frequency and base speed do not fit).
Er-02 Minor Fault • Check the wiring.
• The wiring is faulty. • Check the load. Always perform Auto-Tuning
• The load is too heavy. with the load decoupled from the motor.
Er-03 The STOP button was pressed and Auto-Tuning
Repeat the Auto-Tuning.
was canceled.
Resistance fault
Er-04 • Wrong input data.
• Auto tuning exceeded the given time frame.
• Calculated values out of range.
No-Load Current Error
Er-05 • Check the input data.
• Incorrect data was entered.
• Check the wiring.
• Auto tuning took too long.
• Re-enter the data and repeat the Auto-Tuning.
• Calculated values out of range.
Rated Slip Error
Er-08 • Wrong data input.
• Auto tuning exceeded the given time frame.
• Calculated values out of range.
Er-09 Acceleration error
• Increase the acceleration time C1-01.
The motor did not accelerate for the specified
• Check the torque limits L7-01 and L7-02.
acceleration time.
Er-11 Motor speed fault. • Increase the acceleration time (C1-01).
The torque reference was too high. • If possible, disconnect the load.
Current detection error • Check the wiring.
Er-12 • One or all output phases are lost. • Make sure, that the drive rating fits to the motor.
• Current is either too low or exceeds the drives • Check the load. (Auto-Tuning should have been
rating. performed without the load connected.)
• The current sensors are faulty. • Replace the drive.
Rated current alarm
• Check the V/f pattern setting.
End1 • The torque reference exceeded 20% during
• Perform Auto-Tuning without the load con-
Auto-Tuning.
nected.
• The calculated no-load current is above 80%
• Check the input data and repeat Auto-Tuning.
of the motor rated current.
End2 Motor iron-core saturation alarm • Check the input data.
• Calculated core saturation values out of range. • Check the motor wiring.
• Incorrect data was entered. • Perform Auto-Tuning without load connected.
End3
Rated current alarm Check the input data and repeat tuning.

34 YASKAWA ELECTRIC TOEP C710606 15C YASKAWA AC Drive - V1000 Quick Start Guide
Revision History

The revision dates and numbers of the revised manuals are given on the bottom of
the back cover.

MANUAL NO.‫ޓ‬TOEP C710606 15B

Published in Japan April 2008 07-5 1

Date of Revision number

publication Date of original
publication

Date of Publication Rev. No. Section Revised Content

May 2007 − − First edition

April 2008 1 All Addition: CIMR-VCBA0018

June 2008 2 Back cover Revision: Address

3 Addition: Dimensions
September 2008 Chapter2 New models: CIMR-VC2A0030A to 2A0069A
CIMR-VC4A0018A to 4A0038A

YASKAWA TOBP C730600 22A V1000 Option Unit CC-Link Communications Installation Manual 35
 YASKAWA AC Drive V1000
Compact Vector Control Drive
Quick Start Guide

EUROPEAN HEADQUARTERS
YASKAWA ELECTRIC EUROPE GmbH
Hauptstraβe 185, 65760 Eschborn, Germany
Phone: +49 (0)6196 569 300 Fax: +49 (0)6196 569 398
E-mail: [email protected] Internet: http://www.yaskawa.eu.com
YASKAWA ENGINEERING EUROPE GmbH
Hauptstraβe 185, 65760 Eschborn, Germany
Phone: +49 (0)6196 569 520 Fax: +49 (0)6196 569 598
E-mail: [email protected] Internet: http://www.yaskawa-eng.eu.com
UNITED KINGDOM
YASKAWA ELECTRIC EUROPE GmbH
Unit 3, Centurion Court, Brick Close, Kiln Farm, Milton Keynes, Bucks MK11 3JB, United Kingdom
Phone: +44 (0)1908 556815 Fax: +44 (0)1908 565891
Internet: http://www.yaskawa.eu.com
ITALY
YASKAWA ELECTEIC EUROPE GmbH
Via TRABUCCHI N°28 41013 Castelfranco E.(MO), Italy
Phone: +39 (0)59 92 2121 Fax: +39 (0)59 92 2168
E-mail: [email protected] Internet: http://www.yaskawa.eu.com
U.S.A.
YASKAWA ELECTRIC AMERICA, INC.
2121 Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone: +1 847 887 7000 Fax: +1 847 887 7370
Internet: http://www.yaskawa.com
JAPAN
YASKAWA ELECTRIC CORPORATION
New Pier Takeshiba South Tower, 1-16-1, Kaigan, Minatoku, Tokyo, 105-0022, Japan
Phone: +81 (0)3 5402 4511 Fax: +81 (0)3 5402 4580
Internet: http://www.yaskawa.co.jp

YASKAWA ELECTRIC CORPORATION

YASKAWA

In the event that the end user of this product is to be the military and said product is to be employed in any weapons systems or the manufacture
thereof, the export will fall under the relevant regulations as stipulated in the Foreign Exchange and Foreign Trade Regulations. Therefore, be sure
to follow all procedures and submit all relevant documentation according to any and all rules, regulations and laws that may apply.
Specifications are subject to change without notice for ongoing product modifications and improvements.
© 2007-2008 YASKAWA ELECTRIC CORPORATION. All rights reserved.

MANUAL NO. TOEP C710606 15C

1 YASKAWA ELECTRIC TOEP C710606 15C Published
YASKAWA AC Drive - V1000 Quick Start Guide
in Japan September 2008 07-5 3
08-5-1_YEG