UM1932

User manual
Discovery kit with STM32F469NI MCU

Introduction
The STM32F469I-DISCO discovery board (32F469IDISCOVERY) is a complete
demonstration and development platform for STMicroelectronics ARM® Cortex® -M4 
core-based STM32F469NIH6 microcontroller. This microcontroller features three I2C
interfaces, six SPIs with two multiplexed full-duplex I2S interfaces, SDIO, four USART ports,
four UART ports, two CAN buses, three 12-bit ADCs, two 12-bit DACs, one SAI, 8 to 14-bit
digital camera digital module interface, internal 320+4 Kbytes of SRAM and 2-Mbyte Flash
memory, USB HS OTG and USB FS OTG, Ethernet MAC, FMC interface, MIPI DSI
interface, Quad-SPI interface, JTAG debugging support. This discovery board offers
everything required for users to quickly get started and develop applications easily.
The hardware features on the board help users to evaluate the following peripherals: USB
OTG FS, microSD card, Audio DAC with headset jack, digital microphones, SDRAM, 
Quad-SPI Flash memory, 4" TFT LCD using MIPI DSI interface with capacitive touch
panel.The Arduino™ compatible connectors expand the functionality with a wide choice of
specialized shields.The extension header makes it possible to easily connect a
daughterboard for specific application. The integrated ST-LINK/V2-1 provides an embedded
in-circuit debugger and programmer for the STM32 MCU.

Figure 1. STM32F469I-DISCO board (top view)

Figure 2. STM32F469I-DISCO board (bottom view)

1. Pictures not contractual.

October 2015 DocID028183 Rev 2 1/40

www.st.com 1
Contents UM1932

Contents

1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Product marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Demonstration software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5 Technology partners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

6 Hardware layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.1 Embedded ST-LINK/V2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
6.1.1 Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.1.2 ST-LINK/V2-1 firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.2.1 Power supply sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.2.2 Supplying the board through ST-LINK/V2-1 USB port . . . . . . . . . . . . . . 12
6.2.3 Measurement of current IDD drawn by the STM32F469NI . . . . . . . . . 13
6.2.4 Power related jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.3 Clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.3.1 HSE clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.3.2 LSE clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.4 Reset source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.5 Audio outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.6 Digital microphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.7 USB OTG FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.8 MicroSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.9 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.10 Quad-SPI NOR Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.11 Virtual COM port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.12 Arduino connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.13 Extension connector CN12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.14 DSI LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2/40 DocID028183 Rev 2

UM1932 Contents

6.15 Buttons and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6.16 I2C extension connector CN11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.17 USB OTG FS Micro-AB connector CN13 . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.18 MicroSD connector CN9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.19 ST-LINK/V2-1 USB Mini Type B connector CN1 . . . . . . . . . . . . . . . . . . . 24
6.20 Audio jack CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

7 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Appendix A Mechanical dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Appendix B Federal Communications Commission (FCC) and 

Industry Canada (IC) Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B.1 FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B.1.1 Part 15.19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B.1.2 Part 15.105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B.1.3 Part 15.21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B.2 IC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B.2.1 Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B.2.2 Déclaration de conformité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

8 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

DocID028183 Rev 2 3/40

3
List of tables UM1932

List of tables

Table 1. Power related jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Table 2. Arduino compatible connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 3. Arduino compatible connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 4. Extension connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 5. DSI LCD module connector (CN10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 6. Port assignment for control of LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 7. I2C extension connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 8. USB OTG FS Micro-AB connector CN13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 9. MicroSD connector CN9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 10. USB Mini type B connector CN1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 11. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4/40 DocID028183 Rev 2

UM1932 List of figures

List of figures

Figure 1. STM32F469I-DISCO board (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Figure 2. STM32F469I-DISCO board (bottom view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 3. Hardware block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 4. STM32F469I-DISCO top side layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 5. STM32F469I-DISCO bottom side layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 6. USB Composite device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 7. Extension connector CN12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 8. I2C extension connector (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 9. USB OTG FS Micro-AB connector CN13 (front view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 10. MicroSD connector CN9 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 11. USB type Mini B connector CN1 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 12. STM32F469I-DISCO Discovery board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 13. STM32F469I-DISCO MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 14. Extension connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 15. Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 16. Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 17. Audio codec and microphone MEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 18. 4-inch DSI LCD board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 19. SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 20. QSPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 21. USB OTG FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 22. Arduino UNO connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 23. ST-LINK/V2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 24. Mechanical dimensions in millimeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

DocID028183 Rev 2 5/40

5
Features UM1932

1 Features

 STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory and 324 Kbytes

of RAM in BGA216 package
 On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
– mbed™-enabled (mbed.org)
– USB functions: USB virtual COM port, mass storage, debug port
 4-inch 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive touch
screen
 SAI Audio DAC, with a stereo headphone output jack
 Three MEMS microphones
 MicroSD card connector
 I2C extension connector
 4Mx32bit SDRAM
 128-Mbit Quad-SPI NOR Flash
 Reset and wake-up buttons
 4 color user LEDs
 USB OTG FS with Micro-AB connector
 Three power supply options:
– ST-LINK/V2-1 USB connector
– User USB FS connector
– VIN from Arduino™ compatible connectors
 Expansion connectors and Arduino™ UNO V3 connectors
 Comprehensive free software including a variety of examples, part of STM32Cube
package
 Supported by a wide choice of integrated development environments

6/40 DocID028183 Rev 2

UM1932 Product marking

2 Product marking

Evaluation tools marked as "ES" or "E" are not yet qualified and therefore they are not ready
to be used as reference design or in production. Any consequences deriving from such
usage will not be at ST charge. In no event, ST will be liable for any customer usage of
these engineering sample tools as reference design or in production.
"E" or "ES" marking examples of location:
 On the targeted STM32 that is soldered on the board (for illustration of STM32 marking,
refer to the section “Package information” of the STM32 datasheet available at
www.st.com).
 Next to the evaluation tool ordering part number, that is stuck or silk-screen printed on
the board.

3 Demonstration software

The demonstration software is preloaded in the STM32F469NIH6 Flash memory and in the
MICRON N25Q128A NOR Flash memory. The latest version of the demonstration source
code and associated documentation can be downloaded from the
www.st.com/stm32f4discovery webpage.

4 Order code

To order the Discovery kit based on the STM32F469NI MCU, use the order code:
STM32F469I-DISCO.

5 Technology partners

MICRON:
 128-Mbit SDRAM device, part number MT48LC4M32B2
 128-Mbit Quad-SPI NOR Flash memory device, part number N25Q128A

DocID028183 Rev 2 7/40

39
Hardware layout and configuration UM1932

6 Hardware layout and configuration

STM32F469I-DISCO evaluation board is designed around the STM32F469NIH6 (216-pin

TFBGA package). The Figure 3 illustrates the connection between STM32F469NIH6 and
peripherals (SDRAM, Quad-SPI Flash memory, color LCD, USB OTG connector, Audio, I2C
extension connector, microSD card and embedded ST-LINK). Figure 4: STM32F469I-
DISCO top side layout and Figure 5: STM32F469I-DISCO bottom side layout will help to
locate these features on the actual evaluation board.

Figure 3. Hardware block diagram

93RZHU
6XSSO\

27*
86%FRQQHFWRU
)6

.+]&U\VWDO 57&

*3,2 :DNHXSEXWWRQ

0E4XDG
63,)ODVK 463,
PHPRU\

[/('V *3,2V 0,3,'6, '6,/&'

86$57
67/,1.9
670)1,+ /&'7RXFK
6:' SDQHO
%*$SDFNDJH
,&

,&H[WHQVLRQ
FRQQHFWRU

0E6'5$0 )0&
93RZHU
6XSSO\

,&
$XGLR&2'(&
6WHUHRKHDGSKRQH
0LFUR6'FDUG 6$, RXWSXW
6',2
FRQQHFWRU

63,

6WHUHRGLJLWDO
PLFURSKRQHV

$UGXLQR ([WHQVLRQ
FRQQHFWRU FRQQHFWRU
06Y9

8/40 DocID028183 Rev 2

UM1932 Hardware layout and configuration

Figure 4. STM32F469I-DISCO top side layout

8 /'/'/'/'
'LJLWDO *UHHQ2UDQJH5HG%OXH
PLFURSKRQH /('VUHVSHFWLYHO\

6%
6ROGHU
EULGJH

==
LQFKHV'6,
/&'

/'
9%86/('

6%
/' 6ROGHU
9%86/(' EULGJH

8
'LJLWDO 8
PLFURSKRQH 'LJLWDO
PLFURSKRQH
06Y9

DocID028183 Rev 2 9/40

39
Hardware layout and configuration UM1932

Figure 5. STM32F469I-DISCO bottom side layout

-3
3RZHU &1
VHOHFWLRQ 67/,1.9
/' MXPSHU 86%
9/(' %
5HVHWEXWWRQ
/' %
67/,1.9 :DNHXS
&20/(' EXWWRQ

&1
$XGLRMDFN

&1&1
&1&1
$UGXLQR
&RQQHFWRUV

&1
8 PLFUR6'
670)1,+ FDUG

&1
,&
H[WHQVLRQ
FRQQHFWRU
&1 -3
([WHQVLRQ ,''FXUUHQW
&RQQHFWRU PHDVXUHPHQW
MXPSHU

&1
86%27*
)6
&RQQHFWRU
06Y9

10/40 DocID028183 Rev 2

UM1932 Hardware layout and configuration

6.1 Embedded ST-LINK/V2-1

The ST-LINK/V2-1 programming and debugging tool is integrated on the 
STM32469I-DISCO board. Compared to ST-LINK/V2 the new features supported on 
ST-LINK/V2-1 are:
 USB software re-enumeration
 Virtual COM port interface on USB
 Mass storage interface on USB
 USB power management request for more than 100mA power on USB
This feature is no more supported on ST-LINK/V2-1:
 SWIM interface
For all general information concerning debugging and programming features common
between V2 and V2-1 please refer to ST-LINK/V2 User Manual UM1075.

6.1.1 Drivers
Before connecting STM32F469I-DISCO board to a Windows® 7, Windows® 8 or 
Windows® XP PC via USB, a driver for ST-LINK/V2-1 must be installed. It can be
downloaded from the www.st.com webpage.
In case the STM32F469I-DISCO board is connected to the PC before installing the driver,
the Windows device manager may report some USB devices found on STM32F469I-DISCO
as “Unknown”. To recover from this situation, after installing the dedicated driver
downloaded from the www.st.com webpage, the association of “Unknown” USB devices
found on STM32F469I-DISCO to this dedicated driver, must be updated in the device
manager manually. It is recommended to proceed using USB Composite Device line, as
shown in the below Figure 6.
Note: Prefer using the “USB Composite Device” handle for a full recovery.

Figure 6. USB Composite device

6.1.2 ST-LINK/V2-1 firmware upgrade

ST-LINK/V2-1 facility for debug and flashing of the target microcontroller STM32F469NIH6
is integrated on STM32F469I-DISCO board. For its own operation, ST-LINK/V2-1 employs a
dedicated MCU with Flash memory. Its firmware determines ST-LINK/V2-1 functionality and
performance. The firmware may evolve during the life span of STM32F469I-DISCO to

DocID028183 Rev 2 11/40

39
Hardware layout and configuration UM1932

include new functionality, fix bugs or support new target microcontroller families. It is
therefore recommended to keep ST-LINK/V2-1 firmware up to date. The latest version is
available at www.st.com. ST-LINK/V2-1 supports a mechanism that allows flashing its
dedicated MCU via the USB interface on the hosting board, here STM32F469I-DISCO. The
whole process is controlled from a Windows PC application also available at www.st.com.

6.2 Power supply

6.2.1 Power supply sources

STM32F469I-DISCO board is designed to be powered by the following sources:
 5 V DC from the ST-LINK/V2-1 USB connector CN1 with 500 mA current limitation.
Power mechanism of the board supplied by the USB ST-LINK/V2-1 is explained below
(Section 6.2.2: Supplying the board through ST-LINK/V2-1 USB port). Pins 3 and 4 of
jumper JP2 should be closed by placing a jumper in location called STLK on silkscreen
of the board. Jumper JP5 should be closed.The red LED LD5 is lighted on to confirm
the presence of +5 V voltage.
 5 V DC from the user USB FS connector CN13. Pins 5 and 6 of jumper JP2 should be
closed by placing a jumper in location called USB on silkscreen of the board. Jumper
JP5 should be closed. The red LED LD5 is lighted on to confirm the presence of +5 V
voltage.
 6 V to 9 V DC from VIN pin of Arduino™ compatible connector CN6. The voltage must
be limited to 9 V to keep the temperature of the regulator U10 within its thermal safe
area. Pins 1 and 2 of jumper JP2 should be closed by placing a jumper in location
called E5V on silkscreen of the board. Jumper JP5 should be closed. The red LED LD5
is lighted on to confirm the presence of +5 V voltage.
In case VIN, +5V is used to power the board, this power source must comply with the
standard EN-60950-1: 2006+A11/2009, and must be Safety Extra Low Voltage (SELV) with
limited power capability.

6.2.2 Supplying the board through ST-LINK/V2-1 USB port

To power the STM324F69I-DISCO board in this way, the USB host (a PC) gets connected
with the STM324F69I-DISCO board via USB cable to ST-LINK/V2-1 connector.
In the first step, only the ST-LINK part U3 is powered by the PC. In fact, before USB
enumeration the host PC provides only 100mA to the board at that time. STM324F69I-
DISCO board requests for 500mA power to the host PC. If the host is able to provide the
required power, the enumeration finishes by a “SetConfiguration” command and then, the
power switch ST890 U4 is switched ON, the red LED LD5 is turned ON, thus the board can
consume no more than 500mA. If the host is not able to provide such requested current, the
enumeration fails. Therefore the ST890 U4 remains OFF and the board will not be powered.
As a consequence the red LED LD5 remains turned OFF. In this case it is mandatory to use
another power supply source.

12/40 DocID028183 Rev 2

UM1932 Hardware layout and configuration

To do this, it is important to power the board before connecting it with the host PC, which
requires the following sequence to be respected:
1. Set the jumper in JP2 header in E5V position.
2. Connect an external power source to VIN pin 8 of Arduino connector CN6.
3. Check the red LED LD5 is turned on.
4. Connect host PC to USB connector CN1.
The ST890 power switch protects the USB port of the host against current demand
exceeding 600 mA, should a short-circuit occur on the board.
The STM32F469I-DISCO board can also be supplied from a USB power source not
supporting enumeration, such as a USB charger. In this particular case, the solder bridge
SB16 should be closed. ST-LINK/V2-1 turns the ST890 power switch U4 ON regardless of
enumeration procedure result and passes the power unconditionally to the board.

6.2.3 Measurement of current IDD drawn by the STM32F469NI

The jumper JP5 should be closed (default) to supply the STM32F469NI MCU. To measure
the current IDD drawn by the microcontroller STM32F469NIH6 only, remove the jumper JP5
and replace it by a multimeter.

6.2.4 Power related jumpers

The power supply is configured by setting the related jumpers JP2, JP5 and solder bridge
SB8 as described in Table 1: Power related jumpers.

Table 1. Power related jumpers

Jumper,
Description
solder bridge

JP5 IDD is used to measure STM32 current consumption manually by multimeter.

Default setting: Closed by a jumper
JP5

By default SB8 is closed to power +3V3 from regulator U7.

If the board is powered by the pin 1 of extension connector CN12 or by the pin 4 of
SB8 the Arduino connector CN6, it is mandatory to open SB8 to avoid reverse current
injection in regulator U7.
(Default setting): SB8 closed
JP2 is used to select one of the five possible power supply sources.
To supply the board from the ST-LINK/V2-1 USB connector CN1, JP2 should be set
as shown to the right:
JP2 (Default Setting)

DocID028183 Rev 2 13/40

39
Hardware layout and configuration UM1932

Table 1. Power related jumpers (continued)

Jumper,
Description
solder bridge

To supply the board from the User USB FS connector USB connector CN13, JP2
should be set as shown to the right:

To supply the board from the pin 8 VIN of the Arduino compatible connector CN6,
JP2 should be set as shown to the right:

JP2

To supply the board from pin1 of extension connector CN12 or from pin4 of the
Arduino compatible connector CN6, JP2 should be set as shown to the right (no
jumper):

6.3 Clock source

6.3.1 HSE clock source

By default the HSE clock source of the STM32F469NIH6 is the 8 MHz crystal X2. In that
case, zero ohm R131 is soldered, solder bridge SB19 is open.
It is possible to replace the crystal X2 by the 8 MHz output MCO from the circuit 
ST-LINK/V2-1 U3. In that case, 100 ohms resistor R35 should be soldered, zero ohm R131
should be removed, solder bridge SB19 should be closed. C26 is not necessary and
remains not populated.

6.3.2 LSE clock source

The 32.768 KHz crystal X3 is the clock source for the embedded RTC.

6.4 Reset source

The reset signal of STM32F469I-DISCO board is low active and the reset sources include:
 Reset button B1, providing solder bridge SB1 is closed (default setting)
 Embedded ST-LINK/V2-1, providing solder bridge SB2 is closed (default setting)
 Arduino compatible connector CN6 pin 3
 Extension connector CN12 pin 4

14/40 DocID028183 Rev 2

UM1932 Hardware layout and configuration

6.5 Audio outputs

An audio DAC CS43L22 U5 from Cirrus Logic outputs the audio to a stereo headphone jack
connector.
The digital audio interface SAI of STM32F469NIH6 is connected to the digital audio input
SDIN of the audio DAC. The STM32F469NIH6 controls the audio DAC via the I2C2 bus.
Note that I2C speed of the CS43L22 is 100 kHz max.
The PWM loudspeaker output SPKR_OUTA of the CS43L22 is available at pins 15 and 16
of the extension connector CN12. Each of the two terminals of the external loudspeaker
should be connected to pins 15 and 16 of CN2 respectively. Insure the terminals of the
loudspeaker are not connected to the ground.
The port PE3 STM32F469NIH6 enables the jack headphone output and/or the loudspeaker
SPKR_OUT. Providing the audio DAC registers are properly set, it allows to power down the
loudspeaker and/or the headphone outputs.
The I2C address of the audio DAC is 0x94.

6.6 Digital microphones

Three STMicroelectronics MP34DT01TR MEMS digital microphones are available on the
discovery board STM32F469I-DISCO. Two microphones can be used simultaneously in
stereo mode using PDM mode. By default the microphones U2 and U6 are used and
connected to the DFSDM of the STM32F469I microcontroller (solder bridges SB17 opened,
and SB18 closed). The PDM clock is generated at port PD13 while PDM data are received
by the microcontroller at port PD6.
Instead of using the pair of microphones U2 and U6, it is possible to use the pair of
microphones U2 and U1. To enable this possibility the solder bridge SB17 should be closed
and SB18 opened.
Solder bridges locations are shown in Figure 4: STM32F469I-DISCO top side layout .

6.7 USB OTG FS

An USB OTG full speed communication is available at connector CN13.
The STM32F469I-DISCO discovery board can be powered by the 5 V DC of this USB OTG
FS connection. When the STM32F469I-DISCO is USB host, it supplies the USB peripheral.
In this case the board must be supplied by any of the following sources: ST-LINK/V2-1 USB
connector CN1 or pin VIN of Arduino connector CN6. Refer to Section 6.2: Power supply for
more details on each supply source.
The green LED LD8 will be lit in one of these cases:
 STM32F469I-DISCO works as an USB host and power switch U16 is switched ON.
 VBUS is powered by another USB host when STM32F469I-DISCO works as an USB
device.
Red LED LD9 will be lit when an over-current occurs.

DocID028183 Rev 2 15/40

39
Hardware layout and configuration UM1932

6.8 MicroSD card

MicroSD card with 4 GB or more capacity can be inserted in the receptacle CN9. 4 bits of
the SDIO interface of the STM32F469NIH6 are used to communicate with the microSD
card. The card detection is read by the GPIO PG2: when a microSD card is inserted, the
logic level is 0, otherwise it is 1.

6.9 SDRAM
A 128-Mbit SDRAM MICRON MT48LC4M32B2B5-6A is accessible with the FMC interface
of the microcontroller STM32F469NIH6. The data bus is 32 bits wide.
The SDRAM is composed of four banks of 32 Mbits selected by the address bits A14 and
A15.
Each of the four banks is organized as 4096 rows by 256 columns by 32 bits. Raw and
column addresses are pre-selected using the CAS and RAS signals of the FMC bus.
The SDRAM is selected by SDNE0 and can be addressed from 0xC0000000 to
0xC0FFFFFF.

6.10 Quad-SPI NOR Flash memory

A 128-Mbit Quad-SPI NOR Flash memory (N25Q128A13EF840E from MICRON) is
connected to Quad-SPI interface of the STM32F469NIH6 microcontroller.

6.11 Virtual COM port

The serial interface USART3 is directly available as a virtual COM port of the PC connected
to the ST-LINK/V2-1 USB connector CN1. The virtual COM port settings are configured as:
115200 b/s, 8 bits data, no parity, 1 stop bit, no flow control.

6.12 Arduino connectors

CN5, CN6, CN7 and CN8 are female connectors compatible with Arduino standard. Most
shields designed for Arduino UNO rev.3 can fit to the STM32F469I-DISCO discovery board.
Caution: The I/Os of STM32 microcontroller are 3.3 V compatible while Arduino UNO board is 5 V
compatible.

Table 2. Arduino compatible connectors

Connector Pin Pin name MCU Pin Function

LEFT connectors
1 - - Not connected
2 IOREF - 3.3V Ref
CN6 Power
3 NRST NRST Reset
4 +3V3 - +3.3V input/output(1)

16/40 DocID028183 Rev 2

UM1932 Hardware layout and configuration

Table 2. Arduino compatible connectors (continued)

Connector Pin Pin name MCU Pin Function

5 +5V - +5V output

6 GND - Ground
CN6 Power
7 GND - Ground
8 VIN - +6V to +9V power input(2)
1 A0 PB1 ADC12_IN9
2 A1 PC2 ADC12_IN12
3 A2 PC3 ADC12_IN13
CN8 Analog
4 A3 PC4 ADC12_IN14
(3)
5 A4 PC5 or PB9 ADC12_IN15 or I2C1_SDA(3)
6 A5 PA4 or PB8(3) ADC12_IN4 or I2C1_SCL(3)
1. Before using pin4 of CN6 as +3.3V input, the solder bridge SB8 must be removed. Otherwise
the board STM32F469I-DISCO could be damaged by the overcurrent.
2. The external voltage applied to pin VIN should be in the range 6 to 9V at 25°C ambient
temperature. If a higher voltage is applied the regulator U10 may overheat and could be
damaged.
3. By default pin 5 and pin 6 of connector CN8 are PC5 and PA4 respectively. They are enabled
by the default configuration of solder bridges: SB10 and SB12 closed, SB9 and SB11 opened.
If necessary to have an I2C interface on pins 5 and 6 of connector CN8, change the
configuration solder bridges: open SB10 and SB12, close SB9 and SB11.

Table 3. Arduino compatible connectors

Function MCU Pin Pin name Pin Connector

RIGHT connectors
I2C1_SCL PB8 D15 10
I2C1_SDA PB9 D14 9
AVDD - AVDD 8
Ground - GND 7
SPI2_SCK PD3 D13 6
CN5 Digital
SPI2_MISO PB14 D12 5
TIM12_CH2, SPI2_MOSI PB15 D11 4
TIM12_CH1, SPI2_CS PH6 D10 3
TIM14_CH1 PA7 D9 2
- PG10 D8 1
- PG11 D7 8
TIM3_CH1 PA6 D6 7
TIM5_CH3 PA2 D5 6 CN7 Digital
- PG12 D4 5
TIM5_CH2 PA1 D3 4

DocID028183 Rev 2 17/40

39
Hardware layout and configuration UM1932

Table 3. Arduino compatible connectors (continued)

Function MCU Pin Pin name Pin Connector

- PG13 D2 3
USART6_TX PG14 D1 2 CN7 Digital
USART6_RX PG9 D0 1

6.13 Extension connector CN12

The extension connector CN12 is a 2.54 mm pitch header located at the bottom side of the
STM32F469I-DISCO discovery board. It is composed of 16 square pins of 0.64 mm
arranged in double row and it is compatible with usual connectors mating with 2.54 mm
headers, having 0.64 mm square posts. Pins 1, 2, 15 and 16 are marked on the silkscreen
of the PCB, pin 1 is signaled by a triangle as shown below:

Figure 7. Extension connector CN12

The extension connector gives access to the following communication buses and features:
 CAN2
 USART6 (TX, RX)
 I2S2
 SPI1
 7 timer channels
 2 ADC inputs
 A 1W monophonic loudspeaker output
 System signals: NRST, MCO1, ANTI-TAMP1
 Power supply: +3V3, GND
The STM32F469NIH6 ports and extension connector pins numbers are detailed in the
following Table 4: Extension connector pinout:

18/40 DocID028183 Rev 2

 UM1932
Table 4. Extension connector pinout
Extension
connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
pin

MCU Port - - PA8 NRST PB4 PC6 PA5 PC7 PB5 PB13 PA15 PB12 PC13 PC1 - -
CAN2 - - - - - - - - Rx Tx - Rx - - - -
USART6 - - - - - Tx - Rx - - - - - - - -
I2S2 - - - - - MCK - - - CK - WS - SD - -
SPI1 - - - - - - - - MOSI - NSS - - - - -
TIM3/TI TIM3/ TIM2_
TIM1_ TIM3_ TIM1_ TIM1_
TIMER - - - MISO M8_ SCK TIM8_ CH1/2 - - - -
CH1 CH2 CH1N BKIN
CH1 CH2 _ETR
DocID028183 Rev 2

ADC1/AD ADC123
ADC - - - - - - - - - - - - - -
C2_IN5 _IN11
ANTI Speaker Speaker
SYSTEM +3V3 GND MCO1 NRST - - - - - - - - -
TAMP1 OUTAN OUTAP

Hardware layout and configuration

19/40
Hardware layout and configuration UM1932

6.14 DSI LCD

The LCD module is a 4-inch 800x480 TFT color LCD with capacitive touch panel. The LCD
is connected to the MIPI DSI interface of the microcontroller STM32F469NIH6 via the
connector CN10. The DSI (Display Serial Interface) is a specification of the MIPI Alliance
standard and defines the physical interface and the protocol used by the STM32F469NIH6
microcontroller to communicate with such LCD module.
The following ports of the microcontroller STM32F469NIH6 are dedicated to DSI interface:
DSI_D0_N, DSI_D0_P, DSI_CK_N, DSI_CK_P, DSI_D1_N, DSI_D1_P.
In addition to the DSI dedicated ports, the port PH7 of the microcontroller is used to reset
both the DSI LCD module and the capacitive touchscreen controller.
The port PJ2, connected to the LCD signal TE (Tearing Effect) is an input of the
microcontroller to synchronize the write access from the microcontroller with the LCD scan
refresh, to avoid visible artefacts on the display.
LEDK and LEDA signals of the LCD module are the cathode and anode of the backlight
LEDs.
This backlight requires a power supply voltage of typically 25 V generated from the +5 V by
a switching mode boost converter STLD40DPUR.
By controlling the EN pin of the STLD40DPUR by a low frequency PWM signal, it is possible
to switch on/off or to dim the backlight intensity of the LCD module. The control of EN can be
done by software or by hardware:
 By default, the EN pin of the STLD40DPUR is controlled by the microcontroller
software through DSI commands and CABC signal generated by the LCD module. For
such default configuration the resistor R117 is soldered, R119 is not soldered.
 The STM32F469I-DISCO discovery board offers the option to control the EN pin by
HW through port PA3. In such case, R117 should be removed and R119 soldered.

Table 5. DSI LCD module connector (CN10)

CN10 Signal MCU pins
Description
pin name involved

1 ID Not connect -
2 GND Ground -
3 CABC Content Adaptive Brightness Control -
4 GND Ground -
5 RESX Reset, active low PH7
6 IOVCC Digital supply voltage +3V3
7 GND Ground -
8 HSSI_D0_N MIPI-DSI data lane 0 negative-end I/O DSI_D0_N
9 NC Not connect -
10 HSSI_D0_P MIPI-DSI data lane 0 positive-end I/O DSI_D0_P
11 GND Ground -
12 HSSI_CLK_N MIPI-DSI clock lane negative-end input DSI_CK_N
13 NC Not connect -

20/40 DocID028183 Rev 2

UM1932 Hardware layout and configuration

Table 5. DSI LCD module connector (CN10) (continued)

CN10 Signal MCU pins
Description
pin name involved

14 HSSI_CLK_P MIPI-DSI clock lane positive-end input DSI_CK_P

15 GND Ground -
16 HSSI_D1_N MIPI-DSI data lane 1 negative-end input DSI_D1_N
17 NC Not connect -
18 HSSI_D1_P MIPI-DSI data lane 1 positive-end input DSI_D1_P
19 GND Ground -
20 NC/ERR Not connect -
21 VCC Analog circuitry power supply +3V3
Tearing effect output pin to synchronize MCU to
22 TE PJ2
frame writing
23 LEDK Backlight LED Cathode -
24 LEDA Backlight LED Anode -
25 GND Ground -

6.15 Buttons and LEDs

The black button B1 located bottom side is the reset of the microcontroller
STM32F469NIH6. Refer to the Figure 5: STM32F469I-DISCO bottom side layout .
The blue button B2 located bottom side is available to be used as a digital input or as
alternate function Wake-up. When the button is depressed the logic state is 1, otherwise the
logic state is 0.
Four LEDs located top side are available for the user. Refer to the Figure 4: STM32F469I-
DISCO top side layout . The LEDs are LD1, LD2, LD3, LD4 from left to right with colors
green, orange, red, blue respectively. To light a LED a low logic state 0 should be written in
the corresponding GPIO.Table 6 gives the assignment of control ports to the LED indicators.

Table 6. Port assignment for control of LED indicators

LED Controlled by MCU port Color

LD1 PG6 Green

LD2 PD4 Orange
LD3 PD5 Red
LD4 PK3 Blue

DocID028183 Rev 2 21/40

39
Hardware layout and configuration UM1932

6.16 I2C extension connector CN11

Figure 8. I2C extension connector (front view)

 

 
069

Table 7. I2C extension connector pinout

Pin number Description Pin number Description

1 I2C1_SDA (PB9) 5 +3V3

2 NC 6 NC
3 I2C1_SCL (PB8) 7 GND
4 EXT_RESET(PB0) 8 NC

6.17 USB OTG FS Micro-AB connector CN13

Figure 9. USB OTG FS Micro-AB connector CN13 (front view)

Table 8. USB OTG FS Micro-AB connector CN13

Pin number Description Pin number Description

1 VBUS (PA9) 4 ID (PA10)

2 DM (PA11) 5 GND
3 DP (PA12) - -

22/40 DocID028183 Rev 2

UM1932 Hardware layout and configuration

6.18 MicroSD connector CN9

Figure 10. MicroSD connector CN9 (front view)

Table 9. MicroSD connector CN9

Pin Pin
Description Description
number number

1 SDIO_D2 (PC10) 6 GND

2 SDIO_D3 (PC11) 7 SDIO_D0 (PC8)
3 SDIO_CMD (PD2) 8 SDIO_D1 (PC9)
4 +3.3V 9 GND
5 SDIO_CLK (PC12) 10 MicroSDcard_detect (PG2)

DocID028183 Rev 2 23/40

39
Hardware layout and configuration UM1932

6.19 ST-LINK/V2-1 USB Mini Type B connector CN1

The USB connector CN1 is used to connect the embedded ST-LINK/V2-1 to the PC.

Figure 11. USB type Mini B connector CN1 (front view)

Table 10. USB Mini type B connector CN1

Pin number Description Pin number Description

1 VBUS (power) 4 GND

2 DM 5,6 Shield
3 DP - -

6.20 Audio jack CN3

A 3.5 mm stereo audio jack CN3 is available on STM32F469I-DISCO discovery board to
connect a headphone.

24/40 DocID028183 Rev 2

 7 Schematics

UM1932
Figure 12. STM32F469I-DISCO Discovery board
U_MCU Matched Net Lengths [Tolerance = 250mil]
MCU.SchDoc SDRAM 90MHz U_Memory
i SDRAM 90MHz Memory.SchDoc
I2C1_SCL
ZZ2 SDRAM 90MHz i
I2C1_SDA A[0..11] A[0..11]
SDRAM 90MHz i
A[14..15] A[14..15]
U_AUDIO2 i SDRAM 90MHz
D[0..31] D[0..31]
12mm long plastic standoff AUDIO2.SchDoc i SDRAM 90MHz
SDCLK SDCLK
SDRAM 90MHz i
I2C2_SCL I2C2_SCL SDNE0 SDNE0
SDRAM 90MHz i
I2C2_SDA I2C2_SDA SDNRAS SDNRAS
SDNCAS i SDNCAS
SAI1_SCKA SAI1_SCKA SDNWE SDNWE
SAI1_FSA SAI1_FSA SDCKE0 SDCKE0
ZZ3
SAI1_SDA SAI1_SDA FMC_NBL0 FMC_NBL0
SAI1_MCLKA SAI1_MCLKA FMC_NBL1 FMC_NBL1
SPKR_OUTAP
SPKR_OUTAP MIC_CK MIC_CK FMC_NBL2 FMC_NBL2
12mm long plastic standoff SPKR_OUTAN
SPKR_OUTAN MIC_DATA MIC_DATA FMC_NBL3 FMC_NBL3
SPKR/HP AUDIO_RST AUDIO_RST
Matched Net Lengths [Tolerance = 100mil]
pair differential impedance 100 ohms
U_DSI_LCD DSI
ZZ4 DSI_LCD.SchDoc 500MHz clock diff pairs DSI i
DSI i
I2C1_SCL DSI_CK_P DSI_CK_P
DSI i
I2C1_SDA DSI_CK_N DSI_CK_N
12mm long plastic standoff DSI i U_Arduino_ Connectors
DSI_D0_P DSI_D0_P
DSI i Arduino_ Connectors.SchDoc
DSI_D0_N DSI_D0_N
DSI_D1_P i DSI_D1_P ARD_A0 ARD_A0
DSI_D1_N DSI_D1_N ARD_A1 ARD_A1
DSI_TE DSI_TE ARD_A2 ARD_A2
ZZ5
LCD_INT LCD_INT ARD_A3 ARD_A3
LCD_BL_CTRL LCD_BL_CTRL ARD_A4 ARD_A4
LCD_RESET LCD_RESET ARD_A5 ARD_A5
12mm long plastic standoff
ARD_D0 ARD_D0
ARD_D1 ARD_D1 I2C1_SDA
SPKR/HP ARD_D2 ARD_D2 I2C1_SCL
ARD_D3 ARD_D3
ARD_D4 ARD_D4
ZZ6
ARD_D5 ARD_D5
DocID028183 Rev 2

ARD_D6 ARD_D6 NRST

ARD_D7 ARD_D7
2.5mm diameter plastic screw
ARD_D8 ARD_D8
ARD_D9 ARD_D9
ARD_D10 ARD_D10
Matched Net Lengths [Tolerance = 100mil]
ARD_D11 ARD_D11
U_QSPI QSPI
ARD_D12 ARD_D12
ZZ7 QSPI.SchDoc i QSPI
ARD_D13 ARD_D13
QSPI_CLK i QSPI QSPI_CLK
QSPI_BK1_NCS i QSPI QSPI_BK1_NCS
2.5mm diameter plastic screw i QSPI
QSPI_BK1_IO0 QSPI_BK1_IO0
QSPI i
QSPI_BK1_IO1 QSPI_BK1_IO1
i U_ExtensionConnector
QSPI_BK1_IO2 QSPI_BK1_IO2
ExtensionConnector.SchDoc
QSPI_BK1_IO3 QSPI_BK1_IO3
ZZ8
Same length 133MHz clock MCO1 MCO1
NRST PB4 PB4
PA5 PA5
2.5mm diameter plastic screw
PB5 PB5
PA15 PA15
PC13 PC13
PC6 PC6
PC7 PC7
ZZ9 U_Peripherals
PB13 PB13
Peripherals.SchDoc SPKR_OUTAP
PB12 PB12 SPKR_OUTAP
SPKR_OUTAN
PC1 PC1 SPKR_OUTAN
2.5mm diameter plastic screw
EXT_RESET EXT_RESET
NRST
LED1 LED1
LED2 LED2
I2C1_SCL LED3 LED3
I2C1_SDA LED4 LED4 NRST

4 holes for 2.5 mm diameter screws 24MHz clock U_ST_LINK_V2-1

uSD_CLK uSD_CLK
Hole diameter = 3 mm, pad diameter= 5.5 mm ST_LINK_V2-1.SCHDOC
uSD_CMD uSD_CMD
uSD_D0 uSD_D0
uSD_D1 uSD_D1 STLK_TX STLK_TX
uSD_D2 uSD_D2 STLK_RX STLK_RX
uSD_D3 uSD_D3
H3 H2 uSD_Detect uSD_Detect
WAKEUP WAKEUP SWCLK SWCLK
10MHz clock
SWDIO SWDIO
SWO SWO
H4 H1 8MHz clock
STLK_MCO STLK_MCO NRST
i
track shielded with GND tracks each side.
U_Power
U_USB_OTG_FS Power.SchDoc
differential pair i
USB_OTG_FS.SchDoc
USB_FS1_P Refer to example drawing in STLINK page
USB_FS1_P USB_FS1_P
USB_FS1_N
USB_FS1_N USB_FS1_N

USB_FS1_ID USB_FS1_ID

OTG_FS1_PowerSwitchOn OTG_FS1_PowerSwitchOn
OTG_FS1_OverCurrent OTG_FS1_OverCurrent

Schematics
Note: Text in italic placed on a wire is not the net name. It just helps to identify rapidly
MCU IO related to this wire.
Title: MB1189
Project: STM32F469I-DISCO
25/40

Size: A3 Reference: MB1189 Revision: B-07

Date: 7/22/2015 Sheet: 1 of 12
 Figure 13. STM32F469I-DISCO MCU
26/40

Schematics
SDNWE
PA0
WAKEUP

PA1
ARD_D3
PA2 PC1 to EXT Connector
ARD_D5 PC1
PA4 PC2
ARD_A5 ARD_A1
PA6
ARD_D6
PC3
ARD_A2
PA7
ARD_D9
U14A PC4
ARD_A3
PA8 PA0 N3 M2 PC0
MCO1 PA0-WKUP PC0
PA1 N2 M3 PC1 PC5
PA1 PC1 ARD_A4
PA2 P2 M4 PC2
PA2 PC2
PA3 PA3 R2 L4 PC3
LCD_BL_CTRL PA3 PC3
PA4 N4 N5 PC4 U14B
PA4 PC4
PA5 to EXT Connector PA5 P4 P5 PC5 D2 PD0 B12 N7 PG0 A10
PA5 PA5 PC5 PD0 PG0
PA6 P3 H15 PC6 to EXT Connector D3 PD1 C12 M7 PG1 A11
PA6 PC6 PC6 PD1 PG1
PA7 R3 G15 PC7 to EXT Connector PD2 D12 M13 PG2
PA7 PC7 PC7 uSD_CMD PD2 PG2 uSD_Detect
to EXT Connector PA8 F15 G14 PC8 PC8 PD3 C11 M12 PG3
PA8 PC8 uSD_D0 ARD_D13 PD3 PG3
PA9 E15 F14 PC9 PC9 R135 0 PD4 D11 N12 PG4 A14
VBUS_FS1 PA9 PC9 uSD_D1 LED2 PD4 PG4
PA10 D15 B14 PC10 PC10 PD5 C10 N11 PG5 A15
USB_FS1_ID PA10 PC10 uSD_D2 LED3 PD5 PG5
USB_FS1_N PA11 C15 B13 PC11 PC11 PD6 B11 J15 PG6
USB_FS1_N PA11 PC11 uSD_D3 MIC_DATA PD6 PG6 LED1
USB_FS1_P PA12 B15 A12 PC12 PC12 PD7 A11 J14 PG7
USB_FS1_P PA12 PC12 uSD_CLK PD7 PG7 SAI1_MCLKA
PA13 A15 D1 PC13 to EXT Connector D13 PD8 L15 H14 PG8
SWDIO PA13 PC13-ANTI_TAMP PC13 PD8 PG8 SDCLK
PA14 A14 D14 PD9 L14 D9 PG9 ARDUINO USART6_RX
SWCLK PA14 PD9 PG9 ARD_D0
to EXT Connector PA15 A13 D15 PD10 K15 C8 PG10
PA15 PA15 R87 and R135 are for reserved use PD10 PG10 ARD_D8
PD11 N10 B8 PG11
PD11 PG11 ARD_D7
PB0 R5 R6 PJ0 I2S3_CK PD12 M10 C7 PG12
EXT_RESET PB0 PJ0 R87 PD12 PG12 ARD_D4
PB1 R4 R7 PJ1 0 PD13 M11 B3 PG13
ARD_A0 PB1 PJ1 MIC_CK PD13 PG13 ARD_D2
PB2 M5 P7 PJ2 D0 PD14 L12 A4 PG14 ARDUINO USART6_TX
SB6 OTG_FS1_PowerSwitchOn PB2 PJ2 DSI_TE PD14 PG14 ARD_D1
I2S3_CK PB3 A10 N8 PJ3 TP1 D1 PD15 K13 B7 PG15
PB3 PJ3 PD15 PG15 SDNCAS
Closed by default to EXT Connector PB4 A9 M9 PJ4
PB4 PB4 PJ4 Close to MCU
SB7 to EXT Connector PB5 A8 M14 PJ5 PE0 A6 PH3
SWO PB5 PB5 PJ5 LCD_INT FMC_NBL0 PE0 SDNE0
Open by default PB6 B6 PE1 A5
QSPI_BK1_NCS PB6 FMC_NBL1 PE1
PB7 B5 B10 PJ12 PE2 A3 K4 PH2 R121 2K2
OTG_FS1_OverCurrent PB7 PJ12 AUDIO_RST PE2 PH2 SDCKE0 +3V3
PB8 A7 B9 PJ13 PE3 A2 J4 R124 2K2
I2C1_SCL PB8 PJ13 SPKR/HP PE3 PH3
PB9 B4 C9 PJ14 PE4 A1 H4 PH4 I2C2 to codec:
I2C1_SDA PB9 PJ14 SAI1_FSA PE4 PH4 I2C2_SCL
PB10 P12 D10 PJ15 PE5 B1 J3 PH5 <100kHz
STLK_RX PB10 PJ15 SAI1_SCKA PE5 PH5 I2C2_SDA
R140 1K5 PB11 R13 PE6 B2 P13 PH6
+3V3 STLK_TX PB11 SAI1_SDA PE6 PH6 ARD_D10
to EXT Connector PB12 L13 D8 PK3 D4 PE7 R8 N13 PH7
PB12 PB12 PK3 LED4 PE7 PH7 LCD_RESET
DocID028183 Rev 2

R142 1K5 to EXT Connector PB13 K14 D7 PK4 D5 PE8 N9 P14 PH8 D16
PB13 PB13 PK4 PE8 PH8
PB14 R14 C6 PK5 D6 PE9 P9 N14 PH9 D17
ARD_D12 PB14 PK5 PE9 PH9
PB15 R15 C5 PK6 D7 PE10 R9 P15 PH10 D18
ARD_D11 PB15 PK6 PE10 PH10
C4 PK7 D8 PE11 P10 N15 PH11 D19
PK7 PE11 PH11
D9 PE12 R10 M15 PH12 D20
PE12 PH12
H12 D10 PE13 R12 E12 PH13 D21
R132 DSI_CK_P DSI_CK_P PE13 PH13
C93 3.0pF PC14 E1 H13 D11 PE14 P11 E13 PH14 D22
PC14-OSC32_IN DSI_CK_N DSI_CK_N PE14 PH14
0 PC15 F1 D12 PE15 R11 D13 PH15 D23
PC15-OSC32_OUT PE15 PH15
J12
X3 DSI_D0_P DSI_D0_P
PH0 G1 J13 A0 PF0 D2 E14 PI0 D24
PH0-OSC_IN DSI_D0_N DSI_D0_N PF0 PI0
NX3215SA-32.768K PH1 H1 F12 A1 PF1 E2 D14 PI1 D25
PH1-OSC_OUT DSI_D1_P DSI_D1_P PF1 PI1
F13 A2 PF2 G2 C14 PI2 D26
R133 DSI_D1_N DSI_D1_N PF2 PI2
C94 3.0pF NRST J1 A3 PF3 H2 C13 PI3 D27
NRST NRST PF3 PI3
0 A4 PF4 J2 C3 PI4
PF4 PI4 FMC_NBL2
BOOT0 E6 E5 A5 PF5 K3 D3 PI5
R131 BOOT0 PDR_ON PF5 PI5 FMC_NBL3
PF6 K2 D6 PI6 D28
QSPI_BK1_IO3 PF6 PI6
0 STM32F469NIH6 PF7 K1 D4 PI7 D29
QSPI_BK1_IO2 PF7 PI7
C85 8.2pF PF8 L3 C2 PI8
QSPI_BK1_IO0 PF8 PI8-ANTI_TAMP2
2

R149 10K PF9 L2 E4 PI9 D30

X2 +3V3 QSPI_BK1_IO1 PF9 PI9
R143 R150 PF10 L1 D5 PI10 D31
NX3225GD-8.00M QSPI_CLK PF10 PI10
R144 [N/A] PF11 P8 F3 PI11
SDNRAS PF11 PI11
1

510 [N/A] A6 PF12 M6 E3 PI12

PF12 PI12
A7 PF13 N6 G3 PI13
PF13 PI13
C83 8.2pF close to MCU A8 PF14 P6 H3 PI14
PF14 PI14
+3V3 U14C A9 PF15 M8 G4 PI15
PF15 PI15
SB15 L10 K9
VDD_MCU VDD1 VSS1
Closed by default F11 F10 STM32F469NIH6
VDD2 VSS2
SB19 E7 F6
PH0 VDD3 VSS3
STLK_MCO K5 K6
Open by default VDD4 VSS4
H5 H6
VDD5 VSS5
L8 K7
VDD6 VSS6
L9 K8
VDD7 VSS7
J11 J10
VDD8 VSS8
G11 G10 D[0..31]
VDD_USB33 VSS9 D[0..31]
VDD_MCU E9 F8
VDD10 VSS10
E8 F7 A[0..11]
VDD11 VSS11 A[0..11]
J5 J6
VDD12 VSS12
L5 F4 F2 A[14..15]
VDD13 VSS13_VSS18 A[14..15]
BEAD(FCM1608KF-601T03) K11 K10
VDD14 VSS14
E10 F9
VDD15 VSS15
VDD_MCU VDD_MCU VDDA VDDA F5 G6
VDD17 VSS17
G5
VDD18
L7 L6
C60 C98 C65 C77 R123 VDD19 VSS19
C67 C72 C88 C90 C54 C84 C53 C71 C75 H10
4.7uF 4.7uF 1uF 100nF 0 VSS20
100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF R1
VDDA
P1 M1
VREF+ VREF+ VSSA
N1
VREF-
H11
VDD_MCU VDD_VREGDSI
DSI_VDD12 C1
VBAT +3V3
VDD_MCU VREF+ DSI_VDD12 G13 L5 R122 10K
DSI_VDD12 BYPASS-REG
SB14 K12
DSI_VCAP
Closed by default L11
C80 C78 C86 C87 VCAP1
C74 C69 C95 C68 C91 C73 C89 C92 C70 G12 E11
1uF 100nF 1uF 100nF DSI_VSS VCAP2
100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF 100nF C81
2.2uF STM32F469NIH6
C96 C76
2.2uF 2.2uF Title: MCU
Ceramic capacitor (Low ESR)
Project: STM32F469I-DISCO
Size: A3 Reference: MB1189 Revision: B-07
Ceramic capacitor (Low ESR)
Date: 7/22/2015 Sheet: 2 of 12

UM1932
 Figure 14. Extension connectors

UM1932
+3V3 CN12
MCO1 clock, TIM1_CH1
MCO1 1 2 NRST
3 4
SPI1_MISO, TIM3_CH1 USART6_TX, I2S2_MCK, TIM3/TIM8_CH1
PB4 5 6 PC6
SPI1_SCK, TIM2/TIM8_CH1, ADC1/ADC2_IN5 USART6_RX, TIM3/TIM8_CH2
PA5 7 8 PC7
DocID028183 Rev 2

SPI1_MOSI, TIM3_CH2, I2C1_SMBA, CAN2_RX I2S2_CK, CAN2_TX, USART3_CTS, TIM1_CH1N

PB5 9 10 PB13
SPI1_NSS, TIM2_CH1/2_ETR I2S2_WS, CAN2_RX, TIM1_BKIN
PA15 11 12 PB12
ANTI TAMP1 I2S2_SD, ADC123_IN11
PC13 13 14 PC1
15 16
SPKR_OUTAN SPKR_OUTAP
TSM-108-01-x-DV

post heigth: 5.84mm

Extension connector interfaces

Title: Extension Connectors

Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 3 of 12

Schematics
27/40
 Figure 15. Power
28/40

Schematics
JP1
TSM-102-01-x-SV

U10 U8
Arduino power pin VIN LD1117S50TR E5V +3V3 LD1117S18TR +1V8
3 2 3 2
Vin Vout Vin Vout
4 4
Tab Tab
C36
10uF(25V) C35 C32
10uF 10uF

1
DocID028183 Rev 2

LD5
JP2 +5V red
E5V R7 1 2
1 2
U5V_ST_LINK 3 4 820
5 6
VBUS_FS1
TSM-103-01-x-DV

+5V U7 LD1117S33TR +3V3 VDD_MCU

SB8 JP5
3 2
Vin Vout
4 Closed by default
C29 Tab C37 C41 TSM-102-01-x-SV
10uF 10uF 100nF
1

Open solder bridge if supplied

from pin1 of extension connector Title: Power
Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 4 of 12

UM1932
 Figure 16. Peripherals

UM1932
Button Reset Button
LEDs
+3V3 +3V3 LD1
+3V3 Green
R10 1 2 R2 PG6
LED1
100 510
R6 LD2

1
100K Orange
B2 SB1 1 2 R3 PD4
WKUP NRST LED2
C4 Closed by default 680
[N/A] LD3

1
Red

2
B1 1 2 R4 PD5
LED3
R18 PA0 C3 TD-0341 [RESET/Black] 680
WAKEUP 100nF
330 LD4
R19 Blue

2
220K 1 2 R5 PK3
LED4
680
Wakeup Button

The 4 LEDs are top side

DocID028183 Rev 2

+3V3
MICRO SD EXT/RF E2P Connector
(TF) Card R120 R114 R86 R116 R115
47K 47K 47K 47K 47K
+3V3

PC9
uSD_D1
PC8
uSD_D0
PC11
uSD_D3
PC10
uSD_D2
PC12
uSD_CLK
PD2
uSD_CMD
CN11
I2C1_SDA PB9
I2C1_SDA 1 2
I2C1_SCL PB8 PB0
I2C1_SCL 3 4 EXT_RESET
+3V3 5 6
7 8

1
2
3
4
5
6
7
8
CN9
PJS008-2000 F206A-2*04MGF-A
SMS064FF or SMS128FF SSM-104-L-DH (Samtec)

SW2
SW1
9
10

PG2 R57
uSD_Detect
0

Title: Peripherals
Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 5 of 12

Schematics
29/40
 Figure 17. Audio codec and microphone MEMS
30/40

Schematics
R39 R40 2x20mW stereo headphone output
51 51

R23
C20 C21 GND
0
22nF 22nF 3 CN3
6

4
2
PJ3028B-3
R46 PE3
SPKR/HP R24
0
U5 R47 0
PH5 I2C2_SDA 1 15 47K
I2C2_SDA SDA HP/LINE_OUTA
PH4 I2C2_SCL 2 14
I2C2_SCL SCL HP/LINE_OUTB
3 31
A0 SPKR/HP
GND
PG7 SAI1_MCK 37
SAI1_MCLKA MCLK
PE5 SAI1_SCK 38 4
SAI1_SCKA SCLK SPKR_OUTA+ SPKR_OUTAP
PE6
DocID028183 Rev 2

SAI1_SD 39 6 1W max loudspeaker output to extension connector

SAI1_SDA SDIN SPKR_OUTA- SPKR_OUTAN
PE4 SAI1_FS 40 7
SAI1_FSA LRCK SPKR_OUTB+
PE2 AUDIO_RST 32 9
AUDIO_RST RESET SPKR_OUTB-
+3V3 8 +3V3 C23
R1 VP
10 5
R48 -VHPFILT VP
10K 11
47K C22 FLYN 100nF
C18 30
1uF AIN1B
C1 U2 29
AIN1A
100nF 1 2 12 26
VDD LR FLYP AIN2B
3 1uF 25
CLK AIN2A
5 4 +1V8 24
GND DOUT AIN3B
13 23
+VHP AIN3A
MP34DT01TR 16 22
VA AIN4B
34 21
VD AIN4A
C17 C16 C30 +3V3 20 19
TSTO VQ
C31 36 28 150pF_NPO_5%_0603
TSTO AFILTB
1uF 100nF 100nF 100nF 33 27 150pF_NPO_5%_0603
VL AFILTA
35 18
C25 DGND FILT+
41 17
GND/Thermal Pad AGND C15
U1 PD13 100nF C24 C27 C19
MIC_CK 10uF 1uF
1 2 CS43L22
VDD LR
3
CLK SB17
C2 5 4 PD6
100nF GND DOUT MIC_DATA
Open by default I2C address 0x94
MP34DT01TR I2C speed: 100kHz max

U6
1 2
VDD LR
3
CLK
5 4 SB18 Title: Audio Codec and Microphone MEMS
GND DOUT
Closed by default
MP34DT01TR Project: STM32F469I-DISCO
Located 21mm from U2 (axis to axis) Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 6 of 12

UM1932
 Figure 18. 4-inch DSI LCD board

UM1932
CN10
HSSI_CLK_N 12
DSI_CK_N HSSI_CLK_N
HSSI_CLK_P 14
DSI_CK_P HSSI_CLK_P
HSSI_D0_N 8 +3V3
DSI_D0_N HSSI_D0_N
HSSI_D0_P 10
DSI_D0_P HSSI_D0_P
HSSI_D1_N 16
DSI_D1_N HSSI_D1_N R34
HSSI_D1_P 18
DSI_D1_P HSSI_D1_P 100K
BLVDD
PJ2 TE 22
DSI_TE TE
LCD_RST 5 LCD_RST PH7
RESX LCD_RESET
L3
BEAD CABC 3 open drain
CABC
4.7uH(1A) Z1 C79
VL 4.7uF/50V VH A 24
LEDA
L4 K 23
C63 LEDK
10nF STPS1L40M C66
C64 C61 U13 10nF 1
ID
100nF 4.7uF/10V 8 6 9
SW Vo NC
1 5 BLGND 13
Vi NC NC
BLGND 7 17
EN NC
3 4 20
GND FB NC/ERR
9 2 +3V3
R117 PGND Rset
CABC 21 SB13
VCC
0 STLD40DPUR R59 R58 6 Open by default
C97 C82 IOVCC
BLGND 100K 10 BLVDD
PA3 LCD_BL_CTRL R119 100nF 4.7uF 2
DocID028183 Rev 2

LCD_BL_CTRL GND +5V

[N/A] 4 L1
GND C56
+3V3 BLGND 7 BEAD(FCM1608KF-601T03) C55
GND 10uF
R118 11 100nF
GND
4K7 15 L2
GND
Backlight driver & PFC connector for LCD panel 19 BEAD(FCM1608KF-601T03) BLGND
GND
25
GND
FH26-25S-0.3SHW
FPC03025-14201(ATOM)

ZIF connector placed BOTTOM SIDE

+3V3

R36
4K7
CN2
PB8 3
I2C1_SCL SCL
PB9 4
I2C1_SDA SDA
PJ5 LCD_INT 2
LCD_INT INT
LCD_RST 5 ZZ1
RESET
+3V3
1
VDD
6 LCD P/N: KM-040TMP-02-A
C6 GND
4 inches DSI LCD display
100nF FH19C-6S-05SH
FPC05006-09200(ATOM)
Touch panel connector for LCD panel

ZIF connector placed BOTTOM SIDE

I2C Address:0x54 Mechanical: 2 Slots in PCB for the 2 flex from LCD Title: 4 inch DSI LCD board
Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 7 of 12

Schematics
31/40
 Figure 19. SDRAM
32/40

Schematics
D[0..31]
D[0..31]
A[0..11]
A[0..11]
A[14..15]
A[14..15]
U11
A11 H9 E2 D31
A11 DQ31
A10 G7 D3 D30
A10 DQ30
A9 J3 D2 D29
A9 DQ29
A8 H2 B1 D28
A8 DQ28
A7 H1 C2 D27
A7 DQ27
A6 G3 A1 D26
A6 DQ26
A5 G2 C3 D25
A5 DQ25
A4 G1 A2 D24
A4 DQ24
A3 F3 A8 D23
A3 DQ23
A2 F7 C7 D22
A2 DQ22
Test points are round pads with 1 to 1.27mm diameter bottom side A1 G9
A1 DQ21
A9 D21
Close to Memory A0 G8 C8 D20
A0 DQ20
B9 D19
TP2 TP3 TP4 DQ19
A15 H8 D8 D18
BA1 DQ18
A14 J7 D7 D17
BA0 DQ17
D0 E8 D16
DQ16
PC0 K8
SDNWE WE#
PG15 K7 R2 D15
SDNCAS CAS# DQ15
PF11 J9 N3 D14
SDNRAS RAS# DQ14
PH3 J8 R1 D13
SDNE0 CS# DQ13
PH2 J2 N2 D12
SDCKE0 CKE DQ12
PG8 J1 P1 D11
SDCLK CLK DQ11
M2 D10
DQ10
PI5
DocID028183 Rev 2

F2 M3 D9
FMC_NBL3 DQM3 DQ9
PI4 F8 L2 D8
FMC_NBL2 DQM2 DQ8
PE1 K1 L8 D7
FMC_NBL1 DQM1 DQ7
PE0 K9 M7 D6
FMC_NBL0 DQM0 DQ6
M8 D5
DQ5
E3 P9 D4
NC DQ4
E7 N8 D3
NC DQ3
H3 R9 D2
NC DQ2
H7 N7 D1
NC DQ1
K3 R8 D0
NC DQ0
K2
NU
B2 B3
+3V3 VDDQ VSSQ
B7 B8
VDDQ VSSQ
C9 C1
VDDQ VSSQ
D9 D1
VDDQ VSSQ
E1 E9
VDDQ VSSQ
L1 L9
VDDQ VSSQ
M9 M1
VDDQ VSSQ
N9 N1
VDDQ VSSQ
P2 P3
VDDQ VSSQ
P7 P8
VDDQ VSSQ
A7 A3
VDD VSS
F9 F1
VDD VSS
L7 L3
VDD VSS
R7 R3
VDD VSS
+3V3
MICRON MT48LC4M32B2B5-6A

C46
C43
C50
C47
C45
C48
C59
C51
C44
C52
C58
C42
C57
C49
SDRAM

100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
100nF
Title: SDRAM
Place close SDRAM
Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 8 of 12

UM1932
 Figure 20. QSPI

UM1932
Test points are round pads with 1 to 1.27mm diameter bottom side
Close to QSPI memory

+3V3 +3V3
TP5 TP6 TP7
DocID028183 Rev 2

R55
10K
PB6 QSPI_BK1_NCS
QSPI_BK1_NCS
PF10 QSPI_CLK U12
QSPI_CLK
1 8
S# VCC
6
C
PF8 QSPI_BK1_IO0
QSPI_BK1_IO0
5 C62
DQ0
PF9 QSPI_BK1_IO1 2 100nF
QSPI_BK1_IO1 DQ1
3
DQ2/Vpp/W#
DQ2/V
/ pp/W#
PF7 QSPI_BK1_IO2 7 4
QSPI_BK1_IO2 DQ3/HOLD#
DQ3/H
/ OLD# VSS
PF6 QSPI_BK1_IO3
QSPI_BK1_IO3
MICRON N25Q128A13EF840F
Exposed central pad should not be connected to any voltage on PCB

Title: QSPI
Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 9 of 12

Schematics
33/40
 Figure 21. USB OTG FS
34/40

Schematics
+3V3 +3V3

R158
680

PB7
OTG_FS1_OverCurrent

1
R157 LD9
R43 U16 47K Red

2
[N/A] 2 3 R156 0 CN13
GND FAULT
5 1 1
+5V IN OUT VBUS
PB2

USB_Micro-AB receptacle
R151 0 4 2
OTG_FS1_PowerSwitchOn EN DM
3
C101 DP
STMPS2151STR 4
R152 4.7uF ID
5
10K GND
6
Shield
7
Shield
8
Shield
DocID028183 Rev 2

9
Shield
10
EXP
475900001

PA9 +3V3
VBUS_FS1
PA11 R160 0 MICROAB_N
USB_FS1_N
PA12 R159 0 MICROAB_P
USB_FS1_P
PA10 R161 0 R153
USB_FS1_ID
330

1
LD8
D5 Green

2
B3 A3
Vbus ID
C3 C1
D+out D+in

3
D3 D1
D-out D-in R155 T3
A2 B1 1
Dz Pd1 9013
B2 C2 47K
Pup Pd2

2
D2
GND
R154
EMIF02-USB03F2 10K

USB Full Speed operating range voltage: 3.0V<VDDUSB<3.6V

Title: USB_OTG_FS
Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 10 of 12

UM1932
 Figure 22. Arduino UNO connector

UM1932
Arduino uno connector

LD7 I2C1_SCL
VREF+
I2C1_SDA
2 1 R49 SB5 R41
510 Closed by default 0
+5V +3V3 Green CN5 C13
PB8 [N/A]
SCL/D15 10
PB9
SDA/D14 9
CN6
AVDD 8
1 GND 7
PD3
2 IOREF SCK/D13 6 ARD_D13 SPI2_SCK
NRST PB14
NRST 3 NRST MISO/D12 5 ARD_D12 SPI2_MISO
PB15
4 3V3 PWM/MOSI/D11 4 ARD_D11 TIM12_CH2, SPI2_MOSI
PH6

POWER
5 5V PWM/CS/D10 3 ARD_D10 TIM12_CH1
PA7
DocID028183 Rev 2

6 GND PWM/D9 2 ARD_D9 TIM14_CH1

PG10
7 GND D8 1 ARD_D8
8 VIN
SSW-110-22-x-S-VS
VIN SSW-108-22-x-S-VS CN7
CN8 PG11
D7 8 ARD_D7
PB1 PA6
ADC12_IN9 ARD_A0 1 A0 PWM/D6 7 ARD_D6 TIM3_CH1
PC2 PA2
ADC12_IN12 ARD_A1 2 A1 PWM/D5 6 ARD_D5 TIM5_CH3
PC3 PG12
ADC12_IN13 ARD_A2 3 A2 D4 5 ARD_D4
PC4 PA1

AIN
ADC12_IN14 ARD_A3 4 A3 PWM/D3 4 ARD_D3 TIM5_CH2
PG13
5 A4 D2 3 ARD_D2
PG14
6 A5 TX/D1 2 ARD_D1 USART6_TX
PC5 SB10 PG9
ADC12_IN15 ARD_A4 RX/D0 1 ARD_D0 USART6_RX
Closed by default
SAMTEC SSW-106-22-x-S-VS
PB9 SB9 SSW-108-22-x-S-VS
I2C1_SDA
Open by default

PA4 SB12
ADC12_IN4 ARD_A5
Closed by default
PB8 SB11
I2C1_SCL
Open by default

Title: Arduino Uno connector

Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 11 of 12

Schematics
35/40
 Figure 23. ST-LINK/V2-1
36/40

Schematics
D1 R22 R25 D3
+5V
2K7 4K7 LED_STLINK
VBUS_FS1
+3V3_ST_LINK BAT60JFILM PWR
BAT60JFILM R11 R17
COM 100 100
SB16 D2 U9 LD3985M33R +3V3_ST_LINK
C7 C5 C8 C9 +3V3_ST_LINK
Open by default 1 Vin Vout
5
100nF 100nF 100nF 100nF E5V

3
BAT60JFILM 3
INH
C33 GND BYPASS C38 Red Yellow

USB_RENUMn
R27 D4 1uF 1uF

PWR_EXT

4
STM_JTCK
100K LD6
VUSB_ST_LINK C34 C39 C40
+3V3_ST_LINK HSMF-A201-A00J1
BAT60JFILM 100nF 10nF 100nF R21
0
Board Ident: PC13=0 +3V3_ST_LINK
U3
STLINK V2-1

48
47
46
45
44
43
42
41
40
39
38
37
JTDI
BOOT0

JNRST
VDD_3
VSS_3
PB9
PB8

PB7
PB6
PB5

JTDO

JTCK
C11 C10 +3V3_ST_LINK VUSB_ST_LINK U5V_ST_LINK
10pF 10pF R29 R28 C14
X1 [N/A] 10K 1 36 100nF
VBAT VDD_2
+3V3_ST_LINK 2 1 2 35
PC13 VSS_2
3 34 STM_JTMS
PC14 JTMS
R30 NX3225GD-8.00M SWIM_PU_CTRL 4 33 STL_USB_DP U4
PC15 PA12
100K OSC_IN 5 32 STL_USB_DM 1 6
OSC_IN PA11 IN OUT
OSC_OUT 6 31 T_SWO 2 7
OSC_OUT PA10 IN OUT
STM_RST 7 30 LED_STLINK
/RST PA9 output current limitation : 500mA
Open by default

+3V3_ST_LINK 8 29 MCO R42 100K 8 5

VSSA PA8 FAULT SET
9 28 PWR_ENn
VDDA S2_MOSI R37
DocID028183 Rev 2

SB4 C12 R31 [N/A] AIN_1 10 27 T_JTMS R38 10K

PA0 S2_MISO 2K7
100nF 11 26 T_JTCK 3 4

PB2/BOOT1
PA1 S2_CK ON GND
R33 4K7 12 25 T_SWDIO_IN

S1_MOSI
+3V3 U2_TX

S1_MISO
PB12
ST890CDR

VDD_1
U2_RX
U2_CK
S1_CK

VSS_1
STLINK_TX
R32 4K7 R20 Power Switch to supply +5V

PB10
PB11
PB0
PB1
100 from STLINK USB
RC must be close to SLINK U3

13
14
15
16
17
18
19
20
21
22
23
24
R35 100
MCO
PB11 +3V3_ST_LINK STLK_MCO
STLK_TX
Not Fitted

CUR_SEL
C26

T_NRST
T_JTDO
T_JTCK

T_JRST
T_JTDI
USB Virtual ComPort 20pF
PB10 STLINK_RX
STLK_RX
Not Fitted

R26 T_JTCK PA14

SWCLK
100K
T_JTMS PA13 SWD
SWDIO
T_NRST SB2 to MCU
NRST
VUSB_ST_LINK Closed by default
+3V3_ST_LINK T_SWO SB3
SWO
R9 Closed by default
R15
3

T1 10K 100
USB ST-LINK VUSB_ST_LINK 9013 1 USB_RENUMn

CN1 R16
2

VCC
1 R12 1K5 36K reserved use +3V3_ST_LINK
2 R14 0 STL_USB_DM
D-
3 R13 0 STL_USB_DP CN4
D+
4 R8 100K STM_JTMS
ID 1 2
5 STM_JTCK
GND 3 4
6
SHELL 5
Title: ST-LINK/V2-1
USB-MINI-typeB [N/A]
Project: STM32F469I-DISCO
Size: A4 Reference: MB1189 Revision: B-07
Date: 7/22/2015 Sheet: 12 of 12

UM1932
UM1932 Mechanical dimensions

Appendix A Mechanical dimensions

Figure 24. Mechanical dimensions in millimeter

DocID028183 Rev 2 37/40

39
Federal Communications Commission (FCC) and Industry Canada (IC) Compliance UM1932

Appendix B Federal Communications Commission (FCC)

and 
Industry Canada (IC) Compliance

B.1 FCC Compliance Statement

B.1.1 Part 15.19

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

B.1.2 Part 15.105

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and the receiver.
 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.

B.1.3 Part 15.21

Any changes or modifications to this equipment not expressly approved by
STMicroelectronics may cause harmful interference and void the user’s authority to operate
this equipment.

B.2 IC Compliance Statement

B.2.1 Compliance Statement

Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)

B.2.2 Déclaration de conformité

Étiquette de conformité à la NMB-003 d’Industrie Canada : CAN ICES-3 (B)/NMB-3(B)

38/40 DocID028183 Rev 2

UM1932 Revision History

8 Revision History

Table 11. Document Revision History

Date Version Revision Details

19-Sep-2015 1 Initial release.

Updated Figure 3: Hardware block diagram
Added Section Appendix B: Federal Communications
20-Oct-2015 2
Commission (FCC) and Industry Canada (IC) Compliance and
Section 2: Product marking

DocID028183 Rev 2 39/40

39
 UM1932

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2015 STMicroelectronics – All rights reserved

40/40 DocID028183 Rev 2