TOYOTA MOTOR ASIA PACIFIC
ENGINEERING & MANUFACTURING
CO.,LTD.
INSTALLATION MANUAL
Head Up Display
For IMV 2-4
1
INSTALLATION MANUAL
Head Up Display
Thank you for your purchase of TOYOTA genuine “Head Up Display”. This manual explains the procedure for
Install Head up Display. Please carefully read this manual before operation to ensure correct installation.
Part number Model
PZ065-0K003 KUNXX
TGNXX
COMPONENT PART
1 2 3 4
Installation period: 1 hour
NO. PART NAME PART NO Q'TY TOOS
1 HUD PZ065-0K053 1 1. Clip remover
2 Installation Kit 1 2. Screwdriver
2.1 Velcro 1 3. Ratchet
2.2 Sponge tape PZ065-0K056 1 4. Pliers
2.3 Pattern paper 1 5. Socket No. 8,10,12
2.4 Cable tie 4 6. Alcohol
3 Reflective Film PZ065-0K055 1 7. Wrench Torque 6.9-9.8 N.m
4 Wire Harness PZ065-0K054 1 or 70.4-100 kgf.cm
5 Owner's Manual - 1
TOYOTA MOTOR ASIA PACIFIC
ENGINEERING & MANUFACTURING CO.,LTD.
2
Revision record of installation manual
NO D/M/Y PAGE PIC Details for revision Deleted portion
Checking before installation
Checking before installation
For safety working. Please pay attention with caution symbol as details below.
Caution … If now follow there might cause the accident, injured or take damage to the vehicle
Note … Information in order to work faster
(1) Parking on smooth road, pull hand brake and check brake
(2) Use key start engine without vehicle moves check electric door lock normal operation or not
(3) Caution about parts when uninstall example clip screw bolt or not missing and correct positions when
reinstallation
Assembly
Component
Unload battery terminal (-) Use tool by correct method Caution shape area touch with wire harness
Route the wire harness
- Hold connector when uninstall - Use tape for correct wire together - Insert connector tightly - Don’t too much pull wire
- Don’t pull and hold wire
click
- Use tape for protect wire from - Route wire harness through circle - Correct wire for possible reinstall component
shape area space beware about waterproof
Screw assy
click
Clip lock
waterproof
click
Correct wire After install finished
- Don’t correct wire without - Cut wire over
insulation - Reinstall all parts completely
- Caution terminal cut touch - Correct connector tightly
with another wire beware rattle noise
Click
Caution
In case of operation while connected battery beware force make to shock sensor of safety air back effect to
vehicle damage or injury
Check operation of door lock, electric mirror, Hazard for normal electric system checking
4
Caution of use clip electro taps
(1) In process of cut vehicle’s vinyl beware wire damage
(2) Use clip electro taps although others component already connected. It must connect to vehicle’s wire
(3) Connect wire by clip electro taps. It must has click sound happen that show already connected
(4) Check number of connector, wire of component and vehicle’s wire beware mistake connect position
(5) In case of clip electro taps with wire that same pole please notice connection position
(6) If hinge damage but can completely lock 2 points. It can use with no problem
(7) Don’t reuse clip electro taps. If mistaken position of clip electro taps please cut wire and vehicle’s
wire and protect them by vinyl tape
Clip electro taps procedure
1. In case of vehicle’s wire cover by vinyl tube or vinyl
Electro tap
tape please cut them as appropriate
2. Insert vehicle’s wire in hole tightly
Accessory
harness
Vehicle harness
Vehicle harness 3. After completely insert vehicle’s wire please use
pliers for fold clip electro taps left and right
Accessory
harness together until completely lock (Click)
4. For protect insertion between clip electro taps
please use vinyl tape cover them
Lock
Lock
5
OE part removal
1. DISCONNECT NEGATIVE (-) TERMINAL.
Caution
Check the electrical system of vehicle before installation the
HUD
2. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANAL
2.1 Remove the clip and detach the 2 claws and 3 guides
and remove the No. 1 instrument cluster finish panel.
3. REMOVE COMBINATION METER.
3.1 Remove the 3 screw then remove combination meter
4. REMOVE FRONT ASSIST GRIP SUB-ASSY AT
THE DRIVER SIDE.
4.1 Using a screwdriver, detach the 4 claws and pry out
the 2 assist grip plug.
Hint
Tape the screwdriver before use.
6
4.2 Remove 2 screws and assist grip.
5. REMOVE THE PILLAR GARNISH.
5.1 Using clip remover, detach 2 clip.
5.2 Pull the pillar garnish in the direction indicated by the
arrow which show in the illustration to detach 2 claws.
Then remove the garnish.
Clips
Guide
Overall installation image.
Film
HUD
Ground
IGN
SPD
7
1. INSTALL THE HUD UNIT
1.1 Use velcro to fix HUD on dashboard.
a. - stick velcro's loop side on HUD's bottom.
b. - stick velcro's hook side on dashborad.
A 1.2 Place a pattern paper on the corner right of dashboard.
hint
1. Clean up the inner surface of windshield and
B
dashboard before place the pattern paper.
2. Place a pattern paper to align with pillar garnish(RH)
A,B and light sensor.
Light Sensor
Light sensor
Linght sensor
8
1.3 Stick vecro's hook side on dashborad at the position
"FIX HUD" on a pattern paper.
2. STICK THE REFLECTION FILM ON INNER SURFACE
OF WINDSHIELD.
2.1 Attech the template for attech the Reflective film
on winshield as shown in the picture.
Hint
Clean up the windshield surface; then spread a litle water
on it
2.2 Tear apart the cover paper of reflection fime and
stick it on to the inner surface of winshield.
Hint
Do not have the air bubble after attceh Reflective film
Hint
A Align the film to A and B side.
9
Wiring harness
1. Stick the sponge tape to the edge of body vehicle,
Sponge to the room between front piddar garnish and dashboard.
2. Attech HUD ECU at the duble side tape on the
upper instrument panal by mean of rotate button control
come to driver.
3. Wiring the harness in the direction which show in the picture
GND 3.1 Route the wire harness connector side through
HUD under the air diet, the out at the hole of pillar garnish
3.2 Put the cable into the gap between dash board and
windshield.
3.3 Use cable tie to tiethe cable up at the white mark.
SPD & IGN
4. Connect GND wire.
4.1 Fin out the metal bolt behind combination meter.
4.2 Screw GND wire's washer to the bolt as picture.
Note
Torque controlled
) Parking on at 6.9-9.8road,
smooth N.m pull
(70.4-100 kgf.cm)and
hand brake
Component
Unload battery terminal 10
C10 / C8
Route the wire ha
SPD
IGN
C10 : IMV 4
C8 : IMV2-3
5. Connect speed signal and IG wire.
5.1 Find out the 40 pin connector (combination meter)
5.2 Connect the IG wire (orange-black) to the pin no.21 of the vehicle connector (orange-black)
5.3 Connect the SPD wire (violet-red) to the pin no.6 of the vehicle connector (violet-red)
Correct wire
6. Secvre the fuse case by a cable tie with the vehiclre
main harness.
Caution
Check operation of door lock, electric mirror, Hazard for normal elect
11
System Diagram
IG
1
SPD 2
HUD ECU
3
Ground point behind
combination meter
Re-install the OE part back to original position.
1.Returning parts.
After functional check please carefully reinstall parts and see the condition below.
- Wire Harness (from OE. and accessory) might be mated by re-installs parts.
- Vehicle might injurious or has damage.
2.Caution : When reconnect the negative(-) terminal of battery.
After reconnect battery some parts should be set the initial value so after complete installation
and functional check the initial value should be set.
12
Procedure of verify after install
Complete the installation
Turn IGN power on
Check all segment NO
light up for 3 Secthen Troubleshooting 1
return to zero.
YES
Lift vehicle up and step on the
accelerator.
Dose the display NO
value same with Troubleshooting 2
original meter ?
YES
Put down vehicle
Check operation is completed
13
Troubleshooting 1
Are the cable and NO
HUD correctly Make connection
connected?
YES
Are the Ground/IGN wire NO
correctly connected ?
Make connection
YES
Carry on the rest of the
operation check.
Troubleshooting 2
Are the speed signal wire NO
correctly Make connection
connection ?
YES
Addjust the display NO Refer to the owner
speed ? manual and sitting
YES
Carry on the rest of the
operation check.
14
Setting
All graphic icon of HUD will de displayed for about 3 secounds while power switch on.
Display
Data display
Speed unit
Setting mode
Audio warning icon
Speeding warning
Switch Control
SW1 Setting
SW2 Selection up
SW3 Selection down
SW 4 Close speed warning
Speeding alert mode selection
NORMAL MODE
Press "SW1" and "SW4"
Press "SW4"
ADJUSTED FOR
(Default from factory do not adjust)
PULSE MODE
Press "SW1"
Press "SW4"
SPEED CALIBRATION
(Refer to no.1 in the next page)
FIN TUNING
Press "SW1"
Press "SW4"
SPEED WARNING SETTING MODE
(Refer to no.1 in the next page)
(WARNING 50-70-90-100-110 KM/Hr)
15
1. Fine-Speed tuning mode (There is no need to reset if the displayed value consist with the gauge)
Press "SW1" and "SW4" simultaneously, then press "SW1" again,then the display will show below.
Press /
1) When speed display is too high, decrease it by pressing "SW3" button ; or increase it by "SW2" button
then press "SW4"
2) Confirm the adjustment by the actual driving if the value is exactly in consistency with the gauge value ?
Other mise, report no.1 (previous step)
Remark: Adjustment must be done only once the car stopped.
2. Over speeding setting mode
Press "SW1" and "SW4" asimultaneously, then press "SW1" twice times, the display will show below.
Press /
Use the up down / button to change over speed setting value, press the "SW1" again for next speed limit
setting follow the same produre described abore to complete all setting.
Caution: Default over-speed setting are 50,70,90,100 and 110 KM/Hr
3.Speeding alert mode selection (There are 3 mode for alert)
3.1 Press "SW4" close speed warning alert tone, and then
3.2 Press "SW4" again open speed warning (Speed flash).
16
3.3 Press "SW4" again open speed warning (Speed flashing + Speed warning tone).
Sequence of speed selection mode.
Press
Caution: Once the driving speed is over the setting, audio warning will sounds alarm and icon is lit up.
And will be stopped once the speed is lower the setting within 5 secconds.
17
