125cc RL - TaG

ASSEMBLY INSTRUCTIONS
&
USER MANUAL

MAN-043C -0- MAN-043C

 INDEX

PAGE
Section 1 DESCRIPTION OF THE “Parilla X30 125cc RL - TaG” ENGINE

1.1. Main features 02

1.2. Characteristics of the Engine / Operational limits 03
1.3. Contents of packing 04
1.4. Accessories 05
1.5. Motor identification number 06

Section 2 PREPARATION & INSTALLATION OF THE ENGINE ON THE CHASSIS

2.1. Installation sketch of the engine on the chassis 07

2.2. Install the water-cooling system 08
2.3. Exhaust header assembly 12
2.4. Preparation and installation of the motor-mount 12
2.5. Install the carburettor 13
2.6. Install the engine on the chassis 14
2.7. Install the clutch cover with H.T. coil 15
2.8. Mounting of the electric plant and connectors 16
2.9. Install the intake silencer 20
2.10. Install the exhaust 21

Section 3 ENGINE USE

3.1. Charging of the oil in the gear box 22
3.2. Gasoline and oil 22
3.3. Carburetor adjustment guide 23
3.4. Starting and stopping the engine 24
3.5. Engine running-in 25
3.6. RPM limitation 25
3.7. Inlet silencer 25
3.8. Recommendations on the exhaust system 26
3.9. Recommendations on the battery 27
3.10. Warnings on the electrical system 28
3.11. Spark plug and thermal degree 29
3.12. Choice of the sprocket ratio 30

Section 4 ENGINE BASIC MAINTENANCE

4.1. Centrifugal Clutch 33
4.2. Instructions for the clutch disassembly\ assembly 34
4.3. Gear timing schematic 35
4.4. Replacement of the starter brushes 36
4.5. Scheduled maintenance 42
4.6. Troubleshooting 43
4.7. Engine and accessories preservation 44
4.8. Torque Value 45

Wiring diagram 46

MAN-043C -1-
Section 1 - DESCRIPTION OF THE “Parilla X30 125cc RL - TaG” ENGINE

1.1 MAIN FEATURES

The “Parilla X30” has been expressly designed and tuned for powering the karts for hobby
racing on closed tracks destined for this specific purpose.
When designing this new engine, we have considered the technical solutions already
adopted for the high performance engines, and the experience acquired with the TaG
engines (Touch and Go). This in order to guarantee the highest reliability of components,
when the operating limits are respected.
This engine is a 2 stroke single cylinder.
The cylinder and the crankcase are in aluminium alloy.
The pressed liner is made of centrifugated cast iron, fully machined to guarantee the best
possible stability and sliding surface.
The head is separated from the cylinder and secured by 4 studs.
The crankshaft is built and supported by two ball-bearings. The crankshaft is of steel alloy,
hardened and tempered, as the connecting rod, machined from the full, which runs on roller
bearings.
The crankcase houses a balance shaft, driven by two gears, which rotates opposite to the
crankshaft thus reducing the engine vibrations.
The digital ignition with capacitive discharge is fed by a magneto which generates the spark
energy for the starting of the engine, supplies the advance timing through an integrated
pick-up and recharges the battery.
The ignition includes a digital electronic unit, the stator-rotor, the starter relay, the H.T. coil,
a switch key assembly, and the wiring harness (with a 5A fuse) which connects the whole
system.
The electronic box which controls the advance, the rev. limitation and the engine start/stop
logic , integrates the voltage regulator and the ignition circuit.
The starter relay (Solid type SSR), protected from short-circuits, supplies the power for the
electric starter and is controlled by the power pack.
An RPM limiter, integrated in the power pack, prevents the engine from exceeding 14.000,
15.500 or 16.000 RPM during use, depending on the engine versions.
The spark is generated also without a battery; it is therefore possible, in case of emergency,
to start the engine with an external starter unit.
With the starter key in “RUN” position, the starter activates the Bendix which engages the
starter wheel assembled on the clutch.
The engine is provided with an automatic dry centrifugal clutch with low maintenance and
with interchangeable sprocket.
The carburetor is a diaphragm carburetor, specially designed for this engine and includes
an integral fuel pump filter and an all position mounting capability.
The battery (12 V - 9 Ah) is a sealed, no maintenance one and is not supplied with the
engine, it has to be allocated in the support box which can be easily adapted to all existing
chassis.
The exhaust, included in the supply, is already tuned for the best possible performance.
The engine is supplied with a kit which includes the radiator, the pump, water hoses and
whatever necessary for the assembly on the kart.

MAN-043C -2-
 1.2 CHARACTERISTICS OF THE ENGINE – OPERATIONAL LIMITS

The characteristics of the engine are the following :

 Cycle: OTTO / 2 stroke
 Original cubic capacity: 123.67 cc (125cc max.)
 Original bore: 54.00 mm
 Max. theoretical bore: 54.28 mm
 Stroke: 54.00 mm
 Lubrication: Fuel / oil mix 4% (25:1)
 Induction: Reed valve in the crankcase
 Carburettor: Membrane (TRYTON HOBBY 27-C – Ø26)
 Cooling: Water , forced
 Ignition: Digital/with integrated rev. limiter
 Battery charge: With integral generator
 Electric start: 12V/0.30 Kw
 Clutch: Automatic, dry, centrifugal

Operational limits:
 Max. RPM: 14.000,15.500 and 16.000 (with rev. limiter)
(depending on the versions)
 Min. water temperature: 45°C
 Max. water temperature: 65°C

WARNING:
Never exceed the above limits; no obligation of IAME exists in case the above limits are
exceeded.

MAN-043C -3-
1.3 CONTENTS OF THE PACKING
Each “Parilla X30” engine is supplied with the accessories under shown:
EXHAUST SYSTEM QUANTITY
 Flexible hose 1
 Spring for flexible 3
 Exhaust sheath 1
 Exhaust manifold 1
 Exhaust muffler 1
INDUCTION
 TRYTON HOBBY 27-C carburettor – Ø26 1
 Intake silencer 1
ELECTRICAL PLANT
 Battery support plate 1
 Battery support 1
 Battery stripe 1
 Battery fixing clamps & dampeners 2
 Mounting screws & washers kit 1
 Electronic box 1
 Starter relay 1
 H.T. coil 1
 Starting key assembly 1
 Fixing clamps 8
 NGK BR 10 EG spark plug 1
 Spark plug cap 1
MISCELLANEOUS
 Clutch cover 1
 Starter brushes kit (refill) 1
 Dual-Lock fixing strap 1
WATER COOLING SYSTEM
 Radiator 1
 Radiator support kit 1
 Water hose kit 1
 Complete pump group 1
 Thermostat 1

MAN-043C -4-
 1.4 ACCESSORIES

SPARK PLUG KIT

EXHAUST SYSTEM BRUSHES KIT

BATTERY SUPPORT KIT

THERMOSTAT

ELECTRIC PLANT CLUTCH COVER / H.T. COIL

CARBURETTOR TRYTON HOBBY

INLET SILENCER RADIATOR SUPPORT KIT WATER PUMP ASSEMBLY

WATER HOSES KIT RADIATOR

MAN-043C -5-
1.5 ENGINE IDENTIFICATION NUMBER

The official motor identification number can be found stamped on the lower left part of
the crankcase, next to the electric starter (see fig.). The number normally includes a letter
followed by 4 digits (there can be exceptions in some special cases). Other numbers
stamped on the crankcase or other surfaces of the motor refer to various manufacturing
processes and do not identify the motor.

NOTE:
In case of need for spares and when contacting the IAME Support Centers, please
always refer to the Motor Identification Number and to the motor model.

MAN-043C -6-
 Section 2 - PREPARATION AND INSTALLATION OF THE ENGINE ON THE CHASSIS
NOTE:
In case the engine is supplied already assembled on the chassis, it is at care of the assembler to follow these
instructions. The final customer, in this case, can skip this section and can start reading from section 3.
Whenever the engine or a component is disassembled, it is necessary to always follow the under shown
instructions for proper reassembly.

2.1 INSTALLATION SKETCH OF THE ENGINE ON THE CHASSIS

CHASSIS RIGHT SIDE

CHASSIS LEFT SIDE

MAN-043C -7-
2.2 INSTALL THE WATER COOLING SYSTEM
NOTE: to install the water pump belts it is necessary to remove the rear axle.

1
REINSTALL THE REAR AXLE AFTER HAVING Fig.1
INSERTED TWO BELTS.

SUGGESTION:
INSTALL TWO EXTRA BELTS AS SPARES AND
FIX THEM WITH TAPE TO THE AXLE.

2
INSTALL THE WATER PUMP (1 SCREW M8x45
WITH WASHER AND NUT) ON THE PUMP
BRACKET ON THE REAR CROSS RAIL
(SEE FIG. 1).

TORQUE AT 18÷22 Nm (160 ÷190 in-lb).

IN CASE THERE IS NO BRACKET FOR THIS

PURPOSE, IT IS NECESSARY TO INSTALL THE
PUMP ON REMOVABLE CLAMPS AVAILABLE IN
DIFFERENT DIAMETERS (28/30/32mm).

ASSEMBLE THE PUMP FIXING BRACKET ON

THE CLAMP (N°2 SCREWS M6x12) AND
PLACE THE CLAMPS ON THE REAR CROSS RAIL
(N°2 SCREWS M6x25).
INSTALL THE PUMP ON THE BRACKET (N°1
SCREW M8x45 WITH WASHER AND NUT –
SEE FIG. 2).
TIGHTEN BY HAND THE SCREW ON THE
PUMP FIX. BRACKET
PUMP LETTING IT FREE TO ROTATE, FOR THE
ALIGNMENT AND TENSIONING OF THE
BELTS. SCREW M8X45

SCREW M6X12

Fig.2

SCREW M6X25

3
INSTALL THE DRIVING PULLEY ON THE AXLE (2
CLAMPS AVAILABLE IN DIFFERENT DIAMETERS
30/35/40/50mm) ALIGNING ITS RACE
WITH THE DRIVEN PULLEY ON THE PUMP
(SEE FIG.3).

FIX THE TWO CLAMPS WITH 2 SCREWS

M5x22 (TIGHTEN AT 6÷8 Nm) ( 50 ÷ 70 in-lb).
SCREW M5X22
TIGHTEN THE TWO SCREWS M6x25 ON THE
PUMP FIXING CLAMPS AND THE SCREWS
M6x12 ON THE PUMP FIXING BRACKET.

TIGHTEN AT 8÷10 Nm (70 ÷ 90 in-lb)

Fig.3

MAN-043C -8-
4
INSTALL THE BELTS AND TENSION
(SEE FIG. 4).

TIGHTEN THE SCREW M8x45.

TORQUE AT 18÷22 Nm (160 ÷190 in-lb)

Fig.4

BEFORE INSTALLING THE RADIATOR PREASSEMBLE THE FOLLOWING COMPONENTS

5
INSERT THE 4 RUBBER DAMPENERS INTO THE
FIXING HOLES ON THE RADIATOR
RUBBER DAMPENER
(SEE FIG. 5).

Fig.5

- PLACE THE RADIATOR SUPPORT BRACKET

BETWEEN THE RADIATOR FIXINGS BY TILTING
ONE END AND INSERTING IT THROUGH THE
RUBBER DAMPENERS

(SEE FIG. 6).

NOTE:
OIL THE BRACKET ENDS AND THE
DAMPENERS HOLES.

RADIATOR SUPPORT
BRACKET

Fig.6

MAN-043C -9-
 - COMPLETE INSERTION OF THE RADIATOR
SUPPORT BRACKET IN THE RUBBER
DAMPENERS

(SEE FIG. 7 AND 8).

Fig.7

Fig.8

7
FIX THE RADIATOR SUPPORT BRACKET
INSERTING ALSO THE RADIATOR FIXING
BRACKET (RADIATOR CAP SIDE – N°1 SCREW
M6x90 AND N°1 SCREW M6x85 WITH NUT). RADIATOR FIX. BRACKET.
INSTALL THE “L” SHAPE BRACKET ON THE SCREW M6X90
LOWER RADIATOR CLAMP (AVAILABLE IN
DIFFERENT DIAMETERS 28/30/32mm - 2
SCREWS M6x12) AND FIX IT TO THE TONGUE SCREW M6X12
ON THE RADIATOR SUPPORT BRACKET (N°1
SCREW M8x20 WITH NUT) SCREW M8X20

(SEE FIG. 9).

SCREW M6X85

LOWER FIXING CLAMP

Fig.9

MAN-043C - 10 -
 8
PLACE THE RADIATOR FIXING CLAMP ON THE
CHASSIS SIDE RAIL (BRAKE SIDE) (N°2
SCREWS M6x25). TIGHTEN THE BOLTS BY
HAND
(SEE FIG. 10).

PLACE THE RADIATOR SO THAT THE HOLE ON

THE RADIATOR BRACKET AND ONE OF THE
UPPER HOLES ON THE BEARING SUPPORT
BOX MATCH (N°1 SCREW M8)
ONCE YOU FIND THE CORRECT POSITION
TIGHTEN THE M6x25 SCREWS ON THE
LOWER CLAMP FIXING THE RADIATOR.

TIGHTEN AT 8÷10 Nm (70 ÷90 in-lb).

Fig.10

9
THE KIT INCLUDES THREE RUBBER HOSES

- CONNECT THE FIRST HOSE TO THE FITTING

ON THE RADIATOR INLET AND THE FITTING
ON THE ENGINE OUTLET, TIGHTEN WITH
STEEL CLAMPS ON BOTH SIDES.

- CONNECT THE SECOND HOSE TO THE

FITTINGS ON THE RADIATOR OUTLET AND
THE PUMP INLET, TIGHTEN WITH STEEL
CLAMPS ON BOTH SIDES.

- CONNECT THE THIRD HOSE TO THE

FITTINGS ON THE PUMP OUTLET AND THE
ENGINE INLET. TIGHTEN WITH STEEL CLAMPS
ON BOTH SIDES.

(SEE FIG. 11)

Fig.11

10
TO INSTALL THE THERMOSTAT REGULATING
THE WATER TEMPERATURE, CUT THE HOSE
CONNECTING THE FITTING ON THE
RADIATOR INLET AND THE FITTING ON THE
ENGINE OUTLET.
INSTALL THE THERMOSTAT SO THAT THE
ARROW IS TURNED TOWARDS THE RADIATOR

(SEE FIG. 12)

TIGHTEN WITH STEEL CLAMPS ON BOTH

SIDES.

Fig.12

BEFORE STARTING THE ENGINE, FOLLOW THESE RECOMMENDATIONS:

 Unscrew the cap on the radiator and loosen the breather plug on the engine head.
 Fill the radiator until the water comes out from the plug (there is no air in the system now)
and the radiator is completely filled. Tighten the cap (the system contains appr. 1 lt. of
water).
 It is advisable to put a small cup to recover water from the breather on the cap in case of
boiling water.
 After the engine running-in, check the water level in the radiator and top up if necessary.
 In the event of a long inactivity of the engine, remove the hoses and empty the water
circuit to avoid damages to the engine or parts due to cold temperature.

MAN-043C - 11 -
2.3
EXHAUST HEADER ASSEMBLY Fig.1
NOTE:
THE ENGINE IS SUPPLIED WITH THE EXHAUST
GASKET AND NUTS ALREADY INSERTED. WHEN
THE SHIPMENT IS MADE THE INTERNAL PARTS
OF THE ENGINE ARE PROTECTED BY A BLIND
GASKET. (SEE FIG. 1).

2.3.1 REMOVE THE NUTS AND THE EXHAUST

COVER.

2.3.2 MAKE SURE THE EXHAUST GASKET IS IN

SEAT AND INSTALL THE EXHAUST HEADER (SEE
FIG 2).

2.3.3 INSTALL THE TWO WASHERS 8mm.

Fig.2

2.3.4 INSTALL THE TWO 2 NUTS M8. 13mm SOCKET WRENCH OR (13 mm OPEN WRENCH)
TORQUE AT 18 ÷ 22 Nm (160 ÷190 in-lb)

2.4 PREPARATION AND INSTALLATON OF THE MOTOR-MOUNT

NOTE: ALL THE DIMENSIONS ARE IN MILLIMETERS
2.4.1 DRILL 4 HOLES (DIAM. 8.25÷8.5mm) IN THE MOTOR-MOUNT.

MOTOR MOUNT HORIZONTAL VIEW

MAN-043C - 12 -
 2.4.2 INSTALL THE MOTOR-MOUNT, MAKE 6 mm ALLEN WRENCH
SURE TO USE THE M8 ALLEN SCREWS, WITH A
LENGHT SUCH AS TO ENGAGE, IN THE
CRANKCASE, A THREADED LENGHT OF
16÷19mm (THE SCREW MUST PROTRUDE FROM
THE PLATE FOR 16÷19mm ).

(SEE FIG. 3 AND DRAW. PAG. 11)

4 ALLEN SCREWS M8

TORQUE AT 22÷24 Nm (190 ÷ 210 in-lb)

Fig.3

2.5
INSTALL THE CARBURETOR

2.5.1 REMOVE THE PLASTIC PLUG FROM THE

INLET MANIFOLD

(SEE FIG. 4).

WARNING:
MAKE SURE THAT THE PRESSURE HOLE ON THE
GASKET IS NOT PLUGGED.

Fig.4

2.5.2 INSTALL THE CARBURETOR. 5 mm ALLEN

TWO 2 NUTS M6 AND TWO WASHERS
(SEE FIG. 5).
TORQUE AT 6 ÷ 10 Nm (50÷ 90 in-lb)

WARNING:
WHEN REPLACING THE CARB GASKET ALWAYS
MAKE SURE THAT THE GASKET IS INSTALLED
SO THAT THE HOLE IN THE GASKET MATCHES
WITH THE TWO PRESSURE HOLES IN THE CARB.
AND IN THE CRANKCASE: OTHERWISE THE
ENGINE WON’T START.

Fig.5

MAN-043C - 13 -
2.6 INSTALL THE ENGINE ON THE
CHASSIS

2.6.1 POSITION THE ENGINE ON THE TWO

OUTSIDE MAIN RAILS AND FIX THE MOTOR-
MOUNT WITH TWO CLAMPS.

(SEE FIG. 6)

SUGGESTION:
NEVER TORQUE COMPLETELY THE CLAMPS
UNTIL THE CHAIN IS INSTALLED AND PROPERLY
ALIGNED.

Fig.6

2.6.2 CHECK THE ALIGNMENT OF THE

ENGINE SPROCKET AND THE AXLE SPROCKET
WITH A STRAIGHT EDGE.

(SEE FIG. 7)

Fig.7

2.6.3 INSTALL THE CHAIN (PITCH: 7.775)

(SEE FIG. 8)

Fig.8

2.6.4 MOVE THE ENGINE ON THE RAILS AND

OPTIMIZE THE CHAIN TENSION.

WARNING:
THE PLAY OF THE CHAIN MUST BE APPR. 15mm
(½+¾), MEASURED IN THE SHOWN POINT (SEE
FIG. 9). 15mm

2.6.5 TORQUE THE CLAMP SCREWS

Fig.9

MAN-043C - 14 -
2.7 INSTALL THE CLUTCH COVER WITH 5 mm ALLEN

H.T. COIL
Fig.10
2.7.1 REMOVE THE 3 SCREWS M6x25 ON THE
CRANKCASE (SEE FIG.10) AND INSTALL THE
CLUTCH COVER WITH H.T. COIL. (SEE FIG.11).

TORQUE THE 3 SCREWS AT 8 ÷ 10 Nm (70÷ 90

in-lb).

NOTE:
IF AN HORIZONTAL MOTOR-MOUNT IS USED
CHECK AND SEE IF THERE IS SUFFICIENT SPACE
BETWEEN THE CHAIN AND THE UPPER PART OF
THE CLUTCH COVER. IF THIS IS LOWER THAN
6÷7 mm WIDEN THE CHAIN OPENING WITH A
FILE . TO CHECK THIS WE SUGGEST TO INSTALL
THE SPROCKET WITH THE HIGHEST AVAILABLE
TOOTH NUMBER
Fig.11

5 mm ALLEN
2.7.2 CONNECT THE COIL COPPER CABLE ON
THE HOLE ON THE CRANKCASE (SCREW Fig.12
M6x12

(SEE FIG. 12).

TORQUE AT 8 ÷ 10 Nm (70 ÷ 90 in-lb)

WARNING:
ALWAYS MAKE SURE THAT THE GROUND
CABLE ALWAYS CONNECTS THE COIL WITH
THE ENGINE. AN INADEQUATE GROUNDING
COULD DAMAGE THE IGNITION BEYOND
REPAIR.

THE POSITION OF THE H.T. COIL HAS BEEN

CHOSEN TO BE AS FAR AS POSSIBLE FROM THE
EXHAUST AS THE EXCESSIVE HEAT COULD
DAMAGE THE COIL BEYOND REPAIR.

MAN-043C - 15 -
2.8 MOUNTING OF THE ELECTRIC PLANT
AND CONNECTORS
(complete scheme in the drawing at
the end of the document)

NOTE:
For a correct installation follow the under shown
instructions.

MOUNT THE SILENT BLOCKS ON THE UPPER

CLAMP (FIG. 13). Fig.13
COMPLETE THE MOUNTING OF THE CLAMPS
Fig.14
ON THE BATTERY SUPPORT WITH THE N°4
SCREWS M6x25, N°2 SCREWS FOR EACH
CLAMP
(FIG. 14).

TORQUE AT 6 ÷ 8 Nm (50÷ 70 in-lb)

WRENCH 4mm

NOTA:
THE DIFFERENT HOLES ON THE SUPPORT
ALLOW TO ADAPT THE THE SYSTEM TO ALL
CHASSIS.

PLACE THE SUPPORT PLATE ON THE SUPPORT

AND FIX THROUGH THE N°3 SCREWS M5x10
AND CONCERNED WASHERS AND NUTS.

TORQUE AT 6 ÷ 8 Nm (50÷ 70 in-lb)

WRENCH 4mm

Fig.15
PLACE THE ELECTRONIC BOX ON THE PLATE
AND FIX IT THROUGH THE N.2 SCREWS
M5x15 E AND CONCEARNED WASHERS
AND SELF LOCKING NUTS.

TORQUE AT 6 ÷ 8 Nm (50÷ 70 in-lb)

WRENCH 4mm

WARNING:
THE CABLES HARNESS DOESN’T HAVE TO Fig.16
GET IN CONTACT WITH THE SOIL OR WITH
ROLLING PARTS TO AVOID IRREPARABLE
DAMAGES.
DRILL A HOLE (Ø6mm) IN THE FRONT PART OF
THE RELAY BOX AS SHOWN IN THE PICTURE
AND FIX THE RELAY THROUGH THE SCREW
M5x20 WITH WASHER ON THE PLATE.
(Fig.17)

TORQUE AT 6 ÷ 8 Nm (50÷ 70 in-lb)

WRENCH 4mm

Fig.17

MAN-043C - 16 -
PLACE THE PLASTIC CLAMPS IN THE
DEDICATED HOLES AND PUT THE FUSE
HOLDER IN POSITION AND THEN TIGHTEN
THE PLASTIC CLAMPS TO FIX THE FUSE CASE.
CUT OFF EXCEEDING PLASTIC CLAMPS.

(Fig.18)

Fig.18

MOUNT THE KEY BLOCK IN THE DEDICATED

HOUSING.

(Fig.19)

Fig.19

SLIDE THE BATTERY FIXING STRIPE IN THE

DEDICATED SLOTS.

(Fig.20)

Fig.20

PLACE THE BATTERY IN THE DEDICATED SLOT.

(Fig.21)

Fig.21

PLACE THE CABLES AT DESIRED

CONVENIENCE, IN A PRACTICAL AND SAFE
WAY AND TIGHTEN THE BATTERY STRIPE.

ADVICE:
CONNECT THE BATTERY ONLY BEFORE
STARTING THE ENGINE.
PROTECT THE CONNECTIONS ON THE
BATTERY WITH ISOLATING TAPE TO AVOID
ACCIDENTAL RELEASE OF THE FASTONS.

Fig.22

MAN-043C - 17 -
CONNECT THE STATOR PIN WITH THE PIN
ON THE CABLES HARNESS. Fig.23

(FIG. 23)

CONNECT THE STARTER MOTOR PIN WITH

ITS CORRESPONDING ON THE CABLES
HARNESS.

(FIG. 24).

WARNING:
MAKE SURE THAT THE SECURITY FLAPS SNAP
TO GUARANTEE THE CORRECT CONTACT OF
THE TWO ENDS AND A SAFE TIGHTENING.

Fig.24

VERIFY THE PRESENCE OF THE PLASTIC CLAMP

ON THE STARTER MOTOR AND THAT IT FIXES
THE CABLE ON THE BODY OF THE STARTER
ENGINE.

(FIG. 25).

WARNING:
THIS OPERATION IS VERY IMPORTANT AS THE
VIBRATIONS COULD CAUSE DAMAGES TO
THE INTERNAL STARTER MOTOR
CONNECTIONS. Fig.25

PLACE THE GROUND CABLE BUTTONHOLE

END (Ø 6.5mm) ON THE BACK OF THE
ENGINE.

(FIG. 26).

Fig.26

MAN-043C - 18 -
 ALLEN WRENCH 5 mm
FIX THE BUTTONHOLE END OF THE GROUND
CABLE THROUGH THE M6x12 SCREW Fig.27
PRESENT ON THE STARTER ENGINE.

(FIG. 27)

TORQUE AT 8 ÷ 10 Nm (70÷ 90 in-lb)

WARNING:
THIS OPERATION IS FUNDAMENTAL AS AN
IMPROPER GROUNDING COULD IRREPARABLY
DAMAGE THE CELECTRONIC BOX.

TUBE KEY 10mm

FIX THE BUTTONHOLE END OF THE SECOND
GROUND CABLE TO THE H.T. COIL THROUGH Fig.28
THE M6 NUT OF THE H.T. COIL.
(FIG. 28).

TORQUE AT 8 ÷ 10 Nm (70÷ 90 in-lb)

WARNING:
THIS OPERATION IS FUNDAMENTAL AS AN
IMPROPER GROUNDING COULD IRREPARABLY
DAMAGE THE CELECTRONIC BOX.

CONNECT THE PIN OF THE CABLE OF Fig.29

DELIVRED BY THE H.T. COIL TO THE CABLE
COMING FROM THE CABLES HARNESS.

(FIG. 29)

WARNING:
USE A PLASTIC CLAMP TO FIX THE CABLE ON
THE H.T. COIL TO AVOID THE ACCIDENTAL
RELEASE OF THE PINS.

(FIG. 30)

Fig.30

MAN-043C - 19 -
 CONNECT THE ELECTRONIC BOX TO THE 20
POLES CONNECTOR OF THE CABLES
HARNESS.

( FIG. 31)

CONNECT THE STARTER RELAY TO THE 4

POLES PIN ON THE CABLES HARNESS.

(FIG. 32).

Fig.31

Fig.32
WARNING:
MAKE SURE THAT THE SECURITY FLAPS SNAP
TO GUARANTEE THE CORRECT CONTACT OF
THE TWO ENDS AND A SAFE TIGHTENING.

CONNECT THE PIN OF THE KEY BLOCK TO

Fig.33
THE 8 POLES PIN FROM THE CABLES
HARNESS

(FIG. 33)

WARNING:
MAKE SURE THAT THE SECURITY FLAPS SNAP
TO GUARANTEE THE CORRECT CONTACT OF
THE TWO ENDS AND A SAFE TIGHTENING.

SCREW THE SPARK PLUG CAP ON THE H.T.

COIL CABLE.

(FIG. 34)
Fig.34

Fig.34
FIX THE SPARK PLUG CAP ON THE H.T. COIL
CABLE WITH A PLASTIC CLAMP.
Fig.35
(FIG. 35)

 MOUNT THE SPARK PLUG PROVIDED

WITH THE ENGINE AND TORQUE A 20 ÷
26 Nm (175÷ 230 in-lb)

 PLACE THE SPARK PLUG CAP ON THE

SPARK PLUG.

2.9 INLET SILENCER MOUNTING Fig.36

MAKE SURE THAT THE INTAKE SILENCER IS

POSITIONED WITH THE HOLES UPSIDE AND
THAT THEY ARE NOT OBSTRUCTED.

TIGHTEN THE CLAMP ON THE CARBURETTOR

AND FIX THE INLET SILENCER WITH THE
DEDICATED CLAMP ON THE CHASSIS TUBE.

(FIG. 36)

MAN-043C - 20 -
2.10 INSTALL THE EXHAUST
NOTE:
SEE SECTION 3.8 FOR THE
RECOMMENDATIONS ON THE IDEAL
EXHAUST LENGHT.

2.10.1 INSTALL THE FLEXIBLE (L= 65mm Fig.37

FLEXIBLE COMPLETELY CLOSED –) AND THE
EXHAUST HEADER (SEE FIG. 37) AND FIT THE
INSULATING SLEEVE ON THE FLEXIBLE
FLEXIBLE

(SEE FIG. 38)

Fig.38
INSULATING SLEEVE

2.10.2 INSERT THE FLEXIBLE ON THE

EXHAUST HEADER AND FIX WITH THE 3
SPRINGS

(SEE FIG. 39)

Fig.39

THE ENGINE IS READY TO BE STARTED

MAN-043C - 21 -
 Section 3 - USE OF THE ENGINE

3.1 CHARGING OF THE OIL IN THE GEARBOX

WARNING:
The engine is suplied without oil in the gear box. Before starting the engine fill the box
with SAE 30 oil.
Starting the engine with a dry box will damage the gears beyond repair
- Charge of the gear box:
Put the engine in horizontal position, unscrew
the oil plug (n°1 on the picture), and oil level
plug (n°2 on the picture), fill with oil until it
comes out from the oil level plug (appr. 40cc
of oil). 1
Use a SAE 30 motor oil.
- Check the oil level
Put the engine in horizontal position and
unscrew the oil level plug.
If the level is correct you should see a light
outcome of oil, otherwise top up.
- Discharge the oil
Unscrew the oil level plug and loosen the
charge plug. Tilt the engine to discharge the
oil through the oil level plug.
2
3.2 GASOLINE AND OIL
Use leaded or unleaded Premium gasoline 95 ROM, mixed with oil at 4% (25:1).
Use oils containing Castor Oil which guarantees an optimized lubrication at high
temperature.
As on the other hand, use of Castor Oils creates gummy residues which give origin to
carbon deposits, it is necessary to check and clean, at least every 5 ÷10 hours, the
piston and the head.
Our experience dictates use of oils, such as:
 SHELL ADVANCE RACING M
 ELF HTX 909
 ERG K KART FORMULA
Once the fuel tank is filled, make sure that the gasoline reaches the carburetor before
starting the engine.
Never use the electric starter to suck the gasoline as this could discharge the battery.
SUGGESTION:
Disconnect the plastic tube on the carb. and the vent tube on the tank and pressurize the
vent tube, until the gasoline comes out from the tube on the carb. Make sure that there
is no air in the tube. Connect the tube on the carb. and on the vent.

MAN-043C - 22 -
 3.3 CARBURETOR ADJUSTMENT GUIDE
( L ) LOW SPEED FUEL MIXTURE

( I ) THROTTLE ( H ) HIGH SPEED FUEL MIXTURE

SPEED SCREW

*
1 T.O.
RICH LEAN

1 ¼ T.O. ¾ T.O.

1 ½ T.O.
*
T.O. = TURNS OPEN
Normally the correct setting of the mixture screws, after engine run-in, is the following:
 L (close the screw completely and then open): 1 T.O. (1 turn)
 H (close the screw completely and then open): 1 1/6 T.O. (1 turn and 10’)
Based on various factors as altitude, ambient temperature etc. It might be
necessary to reset the carburetor to optimize the performance of the engine.

WARNING:
Never lean too much as lean mixture will overheat engine and cause seizure
Do not force H or L closed. It may damage the precision machined orifice and render the carb. inserviceable.
The adjustment of screw must be performed with warm engine.

(H) (L) (I)

Adjust T.O. from closed to Adjust T.O. from closed to approximately Close by further 1 ½ T.O.
approximately 1 1/6 T.O. 1 T.O. (1 turn) after contact with throttle
(1 turn and 10’) lever.

Start the engine and warm it. If RPM too

high adjust counterclockwise until clutch is
disengaged.

Turn c.c.w until. max. RPM is Continue to turn clockwise

reached. Adjust further until max. RPM is reached.
(L) Adjust c.c.w. fractionally for
fractionally for rich idle. If RPM If RPM
Slowly adjust clockwise. rich idle.
Trigger accelerator. decreases increases

Engine is now idling at max. attainable

RPM, or slightly lower on rich side.

Adjust I counterclockwise until 2.000 ÷

2.500 RPM is reached.

Recheck L screw for optimum setting

required.

Adjust H until best possible free speed is

reached. Turn clockwise for higher RPM.
Counterclockwise for lower RPM.

Adjust L slightly richer by Bad Return to idle and check acceleration for Good
quick response and smooth pick-up. Engine is ready to operate.
1/8 ÷ ¼ T.O. acceleration acceleration

MAN-043C - 23 -
3.4 STARTING AND STOPPING THE ENGINE

Starting is achieved by the starting key.

This is a 3 position key:
1- STOP (key can be removed)
2- KEY
3- RUN

In STOP position the battery is disconnected and the engine stop signal is sent to the
electronic box.
In KEY position the battery is connected to the system and the stop signal is removed. In
RUN position the battery is always connected and the electric starter, operation signal is
sent to the electronic box.

WARNING:
The starting key assembly is supplied with two original keys. We recommend to separate
the keys and to keep one in a protected place. In case of loss of both keys, it is necessary
to replace the complete assembly.
The starting procedure, from STOP position, is as follows:
A) Turn the key to KEY position (this connect the battery).
B) Turn the key to RUN position to start the engine (the electric starter is immediately
disengaged when turning the key to KEY position, or when the electronic box detects
an engine RPM higher than 1.500 RPM).
C) When the engine is running, the key can be left both in the RUN or KEY position. We
suggest, for pratical reasons, to turn the key to KEY position; this allows with a single
tripping to stop the engine (STOP position) or to restart it in case the engine is stopped
(RUN position).
Note:
- in case the engine is stopped with the key in RUN position, to restart it, turn the key to
STOP position and then again to KEY and RUN position to activate the electric starter.
- With the key in KEY or RUN position and if the engine is stopped, to start the engine an
external starter unit can also be used.
In case the engine cannot be started within 5 seconds (check that gas gets to the carb.)
interrupt and try again after 15 seconds. Short and frequent tries are better than long ones.

To stop the engine turn the key to STOP position both from KEY (1 tripping) or from RUN (2
trippings).

MAN-043C - 24 -
3.5 ENGINE RUNNING-IN

The running-in of the engine must be performed following a few fundamental rules:

1. Adjust the carburetion. Start with an adjustment on the rich side.

2. Warm the engine gradually for about 5 minutes at half throttle, making some laps at
low speed, gently closing and opening the carb. throttle (if a tachometer is installed
never exceed 11.000 ÷ 12.000 RPM). Never keep the same RPM for a long time.

3. Increase the speed for 5 minutes at ¾ throttle opening.

Never keep the same RPM for a long time.

4. Increase the speed for 5 minutes, at max. speed on the twisty parts of the circuit and
making the engine rich at half straight (cover with the hand for an instant the holes
on the inlet silencer keeping the throttle wide open).

WARNING:
Once the running-in is over and the engine is cold, check the torque of the exhaust
header nuts as, during the running-in, the nuts tend to become loose (refer to the
attached table).

3.6 RPM LIMITATION

The electronic box incorporates an RPM limiter which prevents the engine from
exceeding 14.000, 15.500 or 16.000 RPM, depending on the engine versions.
This limit cannot be exceeded otherwise the engine could be damaged by the extremely
high RPM.

WARNING:
Do not keep the engine for a long time at the RPM at which the limiter is functioning. This
would cause malfunctions on the induction and damage the reed valve.
When choosing the sprocket ratio always refer to a maximum limit which has to be
equal to the engine version max rotation limit (i.e. 14.000, 15.500 or 16.000 RPM), so
that the incorporated limiter is not switched on continuously when the engine is running.

3.7 INLET SILENCER

Make sure that the inlet holes on the filter are towards the upper side and that they are
not plugged. Make sure that the clamp on the carburetor is not loosen and that the filter
is well fastened to the chassis.

Regularly clean the inside from oil deposits. If necessary remove the rubber manifold
with filter and clean it with gasoline or solvent.

MAN-043C - 25 -
3.8 EXHAUST SYSTEM

Before each test, make sure that the flexible is not damaged. Replace if necessary.

WARNING:
In case the flexible is damaged, metallic particles could be sucked in the engine and
cause a seizure.

Always make sure that the springs are well hooked and in place. In case of breakage,
replace the broken spring. Never race the kart without the 3 springs in place, as
otherwise the exhaust pipe could vibrate beyond control.

Every 10 15 hours, open the pipe end and make sure that the holes on the internal
counter cone are not plugged.

The best performance is achieved with a total exhaust lenght of:

L = 450 ÷ 455 mm.

Where L is measured from the flange on the exhaust header up to the first welding on
the first cone of the exhaust muffler (see drawing).

To achieve this dimension, the flexible (supplied with the engine) must be cut at a lenght
of 65mm (flexible completely closed).
Having fixed a sprocket ratio, it could be necessary to improve the engine performance
either at low or at high RPM.
This could be achieved by modifying the exhaust lenght.
In general, by shortening the total exhaust lenght the low RPM an improvement at high
RPM is achieved and vice versa, by lenghtening the exhaust lenght the low RPM is
improved.
When testing, never exceed in lenghtening or shortening the flexible by more than 5mm
per time.

MAN-043C - 26 -
3.9 BATTERY

The battery (12 V – 9 Ah) is sealed and without maintenance (battery not included in
the engine package).
In order to lenghten the battery life it is recommended to follow few suggestions:
 When the tension drops below 12.6V. it is necessary to recharge the battery.
 Max. allowed recharging current is 1.8A.
 The ideal recharge is achieved with an average charging current of 0.8 ÷ 1 A.
(recharging time of appr. 10 h.) and at an ambient temperature between 0° and
40°C.

ATTENTION:
An overcharge or an extremely quick charge with excessive current could damage the
battery ( the battery would tend to swell).

Choose a battery charger with the following characteristics:

 Feed tension: 90/250 Vac – 50/60 Hz
 Outlet tension: 15 V full charge – 13.8 stand-by
 Max. outlet current: 2A full charge
During transportation or storage, the battery could loose its charge due to the self
discharge (0.1% max per day).
Fully recharge battery before use.

WARNING:
Always connect the - (negative) terminal before and the pole + (positive terminal after).
Always disconnect the battery in opposite order.
 Recharge the battery at least once every 6 months.
 Never let the battery tension dropping under 8V, as whenever it drops under this
limit, the battery cannot be used any longer and it has to be replaced.
 Never put the battery in contact with solvents, oils, plastifiers or rags containing
such elements. The external case of the battery could be damaged.
 Never press or bend or overheat (by welding) the battery terminals.

Other recommendations

 Pay attention not to have free fires upon or around the battery.
 Never short-circuit the terminals.
 Never open the battery or throw it in the fire.
 In case the electrolyte (diluted Sulfuric Acid) gets in contact with skin or clothes,
wash immediately with water. In case it gets in touch with eyes, wash and apply
for medical assistance.
 Carefully check the external case of battery and replace in case of breakages,
swellings of the case or of battery cover.
 Before use, clean the battery from dust and check that the terminals are not
oxydized or damaged.
 When the battery comes to an end never throw it in the garbage but deliver it to
an authorized disposer.

MAN-043C - 27 -
3.10 WARNINGS ON THE ELECTRICAL SYSTEM
We are here listing the main warnings on the electrical system.
Please keep this in mind during the whole life of the engine.

WARNING:
If these prescriptions are not followed the electrical system and the engine could be
damaged beyond repair. No obligation of IAME exists in this case.
1) Please turn the key to STOP position every time the engine is stopped. If the key is left in
KEY position, for a long time, even if the engine is stopped, the battery would be
discharged completely.
2) Never disconnect the ground cables with eyelets when the engine is in operation.
3) Disconnecting the battery when the engine is in operation DOES NOT increase the
engine performance. Vice versa, the ignition advance could become very irregular at
low RPM thus reducing the performance.
4) To fasten the eyelet terminal (groundings) of the wiring harness always use flat or open
washers. Never use tab washers.
5) When disconnecting the connectors, always press the fixing tongues. Always pull the
connectors to disconnect. NEVER PULL THE CABLES.
6) The electronic box and the starting relay must always be installed with their connector
towards the bottom to avoid back water, dampness or dirt in the connector body.
7) Always correctly fix the H.T. coil with both screws, make sure that the laminations pack
on H.T. coil is connected to the engine with the grounding cable. The eyelet connector
must be directly in contact with the laminations pack on the H.T. coil.
8) Never use H.T. coils different than the original coil on the engine. Use of different coil
may cause damages to the electronic box.
9) The digital assembly needs use of a resistive spark plug cap or spark plug. The resistor
value must be equal or higher than 5 Kohm. Avoid use of resistive H.T. cables.
10) The electrical system is protected against battery polarity reversal. When reversing the
connectors on the battery, the protection circuit activates the fuse as soon as the key is
on KEY or RUN position. The fuse must then be replaced.
11) Replace the fuse after having disconnected both terminals on the battery. Only use 5A
strip fuse. Use of fuses with higher amperage might damage the electronic box
whenever the battery polarity is reversed.
12) Only use sealed lead type batteries as specified by IAME. Only use 12V. batteries.
13) Always disconnect the battery from the electrical system when recharging the battery
with an external battery charger, otherwise the internal voltage regulator could be
damaged.
14) DO NOT connect batteries in parallel; this might cause explosions and damages to the
operator. The recharge of the battery, in normal conditions, is guaranteed by the
electrical system. A few minutes of engine in operation are sufficient to recover the
energy lost when starting the engine.
15) In case the battery must feed other users (Tachometer, Telemetry etc…), first contact
IAME to check the recharge capacity of the system.
16) Modifications, interventions and additions to the original electric system might cause
malfunctions. No obligation of IAME exists in this case.

MAN-043C - 28 -
3.11 SPARK PLUG AND THERMAL DEGREE

The engine is supplied with a standard NGK BR10EG spark plug, which represents a
good compromise between the needs of a good running-in and the racing needs in
normal conditions.
Use of different spark plugs is possible and, as a general information, we are
attaching a correspondence list among spark plugs of other brands, based on thermal
degree which represents the capacity of the spark plug to dissipate the internal heat.
The colour of the various parts of the spark plug more exposed to the combustion
flames gives a good indication on the adequacy of the thermal degree and on the
carburetion. It is necessary though to understand which of the two parameters has to
be changed and only the experience tells how to identify the most proper thermal
degree of a spark plug as lean or rich mixtures can generate the same final look which
can also be achieved with a hot or cold spark plug.
See table:
An excessive warm spark plug shows the symptoms,  Extremely clear colour, porous look and
listed aside. calcification of the electrodes and of the internal
insulation.
WARNING:  Irregularities in the ignition, preignition and
Always use a warmer than standard spark plug with detonation with tendency to perforate the top of the
cold or rainy climate. piston.
 Note: some of these symptoms can be achieved
with lean mixtures.

A correct thermal degree shows:  Colour of the insulator end from yellow grey to
dark brown for mixtures respectively lean or rich.

An excessively cold spark plug shows the symptoms,  Insulator end and electrodes covered with black
listed aside. shady soot.
 Ignition difficulties
WARNING:  Note: a wet or oily electrode could also mean an
Always use a colder than standard spark plug with excessively rich mixture.
hot climates.

COMPARISON TABLE BASED ON

THE THERMAL DEGREE

HOT

BOSCH NGK CHAMPION

WO8CS BR9EG N54R
WO7CS BR10EG N52R
WO6CS BR11EG

COLD

MAN-043C - 29 -
3.12 CHOICE OF THE BEST SPROCKET RATIO

The life of an engine depends on many factors but most of all, upon the speed at which
the engine is operated. If an engine is normally operated at speed higher than what
recommended by the manufacturer, the wears and stress of the various components
(con-rods, roller cages, bearings etc.) will be such as to drastically reduce the life of the
engine itself. It is therefore extremely important that the user respects operating limits
imposed by the manufacturer.
The operating limit for the “PARILLA X30” engine are respectively:
-14.000 Rpm
-15.500 Rpm
-16.000 Rpm
According to the different engine versions.

WARNING:
Never exceed the above limit. No obligation of IAME exists in case the above limit is
exceeded.
In case the user wishes to optimize on the track the sprocket ratio in order to achieve the
best possible performance, without abusing the engine, follow the under shown
recommendations.
The engines are supplied with a 11 teeth sproket (pitch 7.775 mm.), but 10 and 12
teeth sprockets are available as accessories. Table 1 shows the various ratios between
the sprocket on the axle and the engine sprocket given the different axle sprocket.
Tab.1

Sprocket
Sprocket ratio Teeth n° - Engine sprocket Teeth n° - Engine sprocket
ratio

Teeth n° Teeth n°
Axle sprocket 10 11 12 Axle sprocket 10 11 12

72 7,20 6,55 6 83 8,30 7,55 6,92

73 7,30 6,64 6,08 84 8,40 7,64 7
74 7,40 6,73 6,17 85 8,50 7,73 7,08
75 7,50 6,82 6,25 86 8,60 7,82 7,17
76 7,60 6,91 6,33 87 8,70 7,91 7,25
77 7,70 7,00 6,42 88 8,80 8,00 7,33
78 7,80 7,09 6,5 89 8,90 8,09 7,42
79 7,90 7,18 6,58 90 9,00 8,18 7,5
80 8,00 7,27 6,67 91 9,10 8,27 7,58
81 8,10 7,36 6,75 92 9,20 8,36 7,67
82 8,20 7,45 6,83

For the operation limit max. of 14.000, 15.500, 16.000 RPM the following table
(Tab. 2a / 2b / 2c) has been prepared.
SUGGESTION:
 During the track tests we recommend use of a tachometer recording the max. obtained
engine RPM.
 Use spark plug caps with a resistance of 5KΩ to avoid the eventual interferences
between the engine ignition and the tachometer and/or telemetry.

MAN-043C - 30 -
 The following example should clarify the procedure for the optimization of the sprocket
ratio. Assume to use the engine with Z=10 teeth engine sprocket and that during the
preliminary track tests a Z= 77 teeth axle sprocket has been used.

 From Table 1 with Z=10 as engine sprocket and Z= 77 on the axle sprocket, a ratio of
7.70 is found.
 Make a few laps on the track and record the maximum engine rpm achieved.
Let us assume that you detect 13.600 RPM.
 From the Table 2a, to achieve a max RPM of 14.000 RPM (operating limit for the 1st
engine X30 version) a sprocket ratio between 7.83 and 8.05 should be used (having
used during the tests, a sprocket ratio of 7.7 and having achieved 13.600 RPM).
 From Table 1, with these values, a sprocket ratio of 10:78 / 10:80 should be used or,
having a Z=11 on the engine sprocket, a ratio 11:87 should be used.

MAN-043C - 31 -
MAN-043C - 32 -
 Section 4 - BASIC MAINTENANCE

4.1 CENTRIFUGAL CLUTCH

The engine has a low maintenance dry centrifugal clutch. The following prescriptions, if
carefully followed, will allow a clutch longlife.
When starting the engine, make sure that the brake pedal is fully pressed to avoid
sudden accelerations.

WARNING:
Once the engine is started, avoid useless accelerations which can overheat and
deteriorate the clutch. Oil the chain before each session. Immediately after each race or
test, check the engine sprocket . Replace if necessary.
A bad alignment of the engine sprocket with the axle sprocket or the lack of oil will
damage irreparably the sprocket.
Check the clutch:
 every 5 hours of use.
 When metallic noises are heard inside the clutch.
 If the kart dragging speed exceeds 6000 RPM.
 Every time the clutch has overheated (presence of smoke or smell of burning).
To check the clutch, you must remove the clutch cover and the clutch drum.
Replace the clutch:
 whenever the thickness of the friction material (see drawing) is lower than 1.5mm on
point A of the clutch or if the body diameter is lower than 83mm.
 Whenever the external friction material in the A portion of the clutch is very rough
(wear or degradation of the friction material due to overheating).

WARNING:
In case the friction material has been totally worn out and there has been a metal
contact between the clutch body and the clutch drum, it is necessary to replace the
clutch drum. See drawing.

MAN-043C - 33 -
4.2 INSTRUCTIONS FOR THE DISASSEMBLY/ASSEMBLY OF THE CLUTCH

WARNING:
the following operations can be performed by a skilled mechanic, under the
conditions to have available the dedicated tools shown in the text, otherwise it is
necessary to apply to an Authorized Service Center.
Refer to the following drawing during the operations.

1 Drum nut 5 Screw 9 Clutch body

2 External washer 6 Clutch drum 10 Starter ring
3 Roller cage 7 Internal washer 11 Screw
4 Sprocket 8 Locking nut

OPERATIONS TOOLS

Clutch disassembly

1. Remove the clutch cover (3 screws M6).  Allen wrench 5mm – T type
2. Remove the Bendix support and replace it with starter
wheel locking tool.  Starter wheel locking tool: P.N. S884

3. Remove nut (1 nut M10).  12 point wrench 17 mm

4. Remove the external washer, the drum complete with

roller cage, the internal washer.
5. Remove the special tool from the head and using the  Starter wheel locking tool: P.N. S884
clutch wrench remove the M20x1 nut and the starter  30mm socket.
wheel.

WARNING: turn clockwise as the nut has left thread

6. Apply the clutch puller on clutch hub and remove the  Clutch puller: P.N. ATT-026
clutch hub with the starter wheel.  12 point wrench 12mm.

7. Remove the starter wheel (3 screws M6)  12 point wrench 5mm

MAN-043C - 34 -
Before assembling the clutch, wash with diluent the shaft taper, the connecting hole on the clutch body, the
clutch drum and the starter wheel.

Install clutch

1. Install the starter wheel on the clutch hub by matching  12 point wrench 10 mm
the three holes and the dragging pin (3 screws M6). (torque at 10 Nm) (90 in-lb)
ATTENTION: make sure to always install the Ø 7 (apply “Loctite”on the threads)
mm dragging pin as otherwise, the eventual kick
backs, could break the screws.
2. Install clutch body and the cone safety washer. Apply “Loctite 641” for coaxial lockings
3. Install the clutch body fixing nut and starter wheel,  Starter wheel locking tool: S 884
using the 30mm clutch wrench.  12 point wrench 30 mm.
(torque at 100 ÷ 110 Nm) (885 ÷ 970 in-
ATTENTION: turn counterclockwise as nut has left lb)
thread.
4. Install the internal washer.
ATTENTION: install washer with bevel towards
internal part of the engine.
Clean the roller cage and grease it before installing it
on the crankshaft.
5. Install the clutch drum and the external washer.
ATTENTION: install washer with bevel towards
internal part of the engine.
 Starter wheel locking tool: S 884
6. Install the starter wheel locking ool to prevent the shaft
 17 mm socket
from turning and install the clutch cover (M10 nut) .
(torque at 30 ÷ 40 Nm) (265 ÷ 350 in-lb)
 Allen wrench 5 mm – T type.
7. Install the clutch cover (3 screws M 6).
(torque at 8 ÷ 10 Nm) (70 ÷ 90 in-lb)

4.3 GEAR TIMING SCHEMATIC

In case of assembly of the gears which drive the balance shaft, assembly must be
performed following the timing schematic shown below.

ATTENTION:
An uncorrect assembly of the gears can cause a malfunction in the vibration reduction
system.

MAN-043C - 35 -
4.4 REPLACEMENT OF THE STARTER BRUSHES

OPERATIONS PICTURES

1. DISASSEMBLE THE STARTER

- UNSCREW N°2 SCREWS M6x35

(see Fig.1).

(5mm ALLEN WRENCH – T TYPE)

Fig.1

Fig.2

- REMOVE STARTER

(see Fig.2).

NOTE:
ON THE ENGINES MANUFACTURED AFTER
SEPTEMBER ‘05, THE STARTER CAN BE
REMOVED WITHOUT TAKING AWAY THE
GEARS COVER BUT SIMPLY BY REMOVING
THE COVER CLAMP (see drawing)

MAN-043C - 36 -
2. OPENING THE STARTER Fig.3
Fig.1
-REMOVE THE PLASTIC CLAMP AND UNSCREW
THE SCREW M4 FIXING THE INPUT CABLE TO
THE STARTER

(see Fig.3)

(PHILLIPS SCREWDRIVER)

Fig.4

- UNSCREW 3 SCREWS M5 “C”

(see Fig.4)

(PHILLIPS SCREWDRIVER)

MAN-043C - 37 -
 - REMOVE DRUM FROM STARTER Fig.4
KEEPING ROTOR IN ITS SEAT
(BE SURE TO HOLD THE ROTOR ON ITS
TOOTHED SIDE TO PREVENT BRUSHES FROM
FALLING OUT FROM THEIR SEAT)
(see Fig.5)

Fig.5

Fig.6
- REMOVE ROTOR FROM STARTER HEAD

(see Fig.6)

ATTENTION:
WHEN EXTRACTING ROTOR, THE BRUSHES
MAY SPRING OUT FROM THEIR SEATS.

3. Fig.7
REPLACING THE BRUSH “A”

- UNSCREW THE 2 SCREWS M4 “D”

RETAINING THE PLATE “E”

(see Fig.7).

(PHILLIPS SCREWDRIVER)

Fig.8

- REMOVE THE LITTLE RUBBER CAP “F”

(see Fig.8).

(PLIERS)

OUR SUGGESTION:
SLIGHTLY OIL THE TIN PLATE TERMINAL END,
TO MAKE EASIER THE EXTRACTION OF THE
LITTLE RUBBER CAP.

MAN-043C - 38 -
MAN-043C - 39 -
- REMOVE SILICONE FROM BRUSHES WITH A
SCREWDRIVER

(see Fig.9).

- REMOVE SPRINGS

Fig.9

Fig.9

- MAKING PRESSURE EXTERNALLY ON THE TIN

PLATE TERMINAL, REMOVE BRUSH.

(see Fig.10).

Fig.10

- INSTALL NEW BRUSH TERMINAL INSIDE

(see Fig.11).

- PLACE LITTLE RUBBER CAP ON THE TERMINAL

Fig.11

- REINSTALL THE PLATE AND FIXE IT

WITH THE 2 SCREWS M4

(see Fig.12).
Fig.12
(PHILLIPS SCREWDRIVER)

MAN-043C - 40 -
MAN-043C - 41 -
4. REPLACEMENT OF THE BRUSH “B” Fig.13

- UNLOOSE THE SCREW M3 “G”

(see Fig.13)

- EXTRACT THE BRUSH

- FIX THE NEW BRUSH WITH SCREW M3

(PHILLIPS SCREWDRIVER)

5.
CLOSING THE STARTER

- INSERT THE NEW BRUSH SPRING "A" INTO

ITS SEAT.

- INSTALL THE BRUSH .

- KEEP THE BRUSH IN PLACE BY PRESSING

TOWARDS THE OUTER AND CLAMP IT WITH
AN IRON WIRE BENT AS A HOOK.

REPEAT THE SAME PROCEDURE TO INSTALL Fig.14

THE BRUSH “B”

(see Fig.14).

- INSTALL THE STARTER ROTOR BETWEEN THE

BRUSHES AND CHECK, THAT THEY ARE
ALWAYS IN CONTACT WITH THE CYLINDRIC
COPPER PART OF THE ROTOR, EVEN WHEN
THEY ARE RELEASED

(see Fig.15). Fig.15

OUR SUGGESTION:
TO IMPROVE THE BRUSHES LIFE, SECURE THE
LITTLE WIRES WITH SILICONE
Fig.16
(see Fig.16).

MAN-043C - 42 -
 - CHECK THAT O-RING "H" IS INSTALLED ON
THE STARTER HEAD.

- INSERT STARTER DRUM ON THE HEAD BEING

CAREFUL TO PREVENT ROTOR FROM
ROTATING AND TO PREVENT THE BRUSHES
FROM FALLING OUT OF THEIR SEAT

(see Fig. 17).

Fig.17

- SCREW THE 3 SCREWS M5

(see Fig.18).

(PHILLIPS SCREWDRIVER)

Fig.18
- CHECK THAT THE STARTER ROTOR ROTATES
FREELY.
Fig.19

- CONNECT THE INPUT WIRING

TO THE STARTER WITH THE SCREW M4

(see Fig.19).

(PHILLIPS SCREWDRIVER)

- SECURE THE WIRE TO THE STARTER

BY MEANS OF A PLASTIC CLAMP (see Fig.20).

6. ASSEMBLING THE STARTER

- PLACE THE STARTER INTO THE CRANKCASE

(see Fig.20).

OIL O-RING TO MAKE EASIER Fig.20

INSTALLATION.

N°2 SCREWS TCH M6x35

TIGHTEN AT A 8÷10 Nm ( 70÷90 in-lb )

(5mm WRENCH – T TYPE)

MAN-043C - 43 -
4.5 SCHEDULED MAINTENANCE

Following some simple maintenance standards will allow the engine to perform more
reliably and have a longer life.

SCHEDULE COMPONENTS ACTIONS AND COMMENTS

Before using Exhaust flexible Check status
Exhaust spring Check status
Insulating sleeve Check status
Silencer Check status and fixing
Check wear
Engine sprocket Check alignment with axle
sprocket
Engine chain Check wear, tensioning and oil
chain
Battery Check status and charge
Cables and connectors Check status and connectors
Grounding of engine and Check status and connectors
electronic box
Engine mounts and clamps Check torques
Battery support and clamps Check torques
After use Battery Disconnect
Chain Check status and oil chain
Engine External cleaning
Every 5 ÷ 10 hours Remove cover (see fig.) and
Bendix assembly
clean internally

Exhaust muffler Remove muffler end, clean

Inlet silencer Open, clean
Engine head Open, clean
Clutch Open, check status of parts
Every 20 hours Piston and con-rod assembly Check and replace worn parts
Crankshaft Check and replace worn parts
Bearings / balance shaft Check and replace worn parts
Gears Check and replace worn parts
Balance shaft Check and replace worn parts

MAN-043C - 44 -
4.6 TROUBLESHOOTING
Below are some common faults, their probable causes and suggested remedy.

FAULTS PROBABLE CAUSES REMEDY

Starter will not crank when turning Bad connections on starter cables Check and tighten
the key to RUN position
Bad grounding Check connections and tighten
Interruption on fuse Replace 5A strip fuse, after
checking for eventual reversal of
battery polarity.
Damaged cables Replace
Battery connection loose Check and tighten

Battery discharged Recharge or replace battery

Starter failure Overhaul starter
Apply to Authorized Service
Electronic box or relay failure
Centers
Starter cranks but engine won’t start Bad cable connections Check connectors
when turning the key in RUN
position
Bad H.T. coil connections or coil Check/replace
failure
Bad H.T. coil grounding Check grounding
Electronic box or ignition failure Apply to Authorized Service
Centers
Wet spark plug Replace
Malfunction on induction system Check status and connection on
fuel pipe
Replace gaskets and membranes
on carburetor
Check reed petals. Replace if
necessary.
Engine starts but it stops after a few Bad cable connections Check stator connector
seconds when turning the key in
RUN position
Electronic box or starter failure Apply to Authorized Service
Centers
Bad carburetor adjustment Check carburetor adjustment (see
( screw I) sect. 3.3)
The starter cranks also after the Electronic box failure Apply to Authorized Service
engine is running. Centers
Rough idle Bad carb. adjustement ( screw I) Check carburetor adjustment (see
sect. 3.3)
Drop in engine performance Bad compression Check piston
Bad carburetor adjustment Check carburetor adjustment (see
sect. 3.3)
Insufficient fuel flow Check fuel flow lines and inlet filter
Dirty inlet silencer Check and clean
Burning smell, smoke Clutch overheating Check clutch (see sect. 4.1)
Clutch engages at too high RPM Excessive wear of friction material Check clutch (see sect. 4.1)
Exhaust too noisy Damaged flexible Check and replace if necessary
Springs damaged or lost
Damaged insulating sleeve
Damaged exhaust header

MAN-043C - 45 -
4.7 ENGINE PRESERVATION

When engine is to remain unoperative for a long period it must be preserved as follow:

 Disconnect the battery and charge it periodically (see sect. 3.9).

 Disconnect carburetor and clean it.
 Seal with tape the engine inlet and exhaust.

The external of the engine must be cleaned. Spray with protective oil, the steel parts
subject to oxidation. Keep the engine in a dry ambient.

In the event of a long unoperative period of the engine, release the hose fixed between
the water pump inlet and the radiator outlet (as shown in the picture) and empty the
water circuit to avoid damages to the engine and the accessories due to freezing.

MAN-043C - 46 -
4.8 TORQUE VALUES

MAN-043C - 47 -
1. ELECTRONIC BOX
2. RELAY
3. STARTER KEY
4. FUSE HOLDER
5. BATTERY
6. IGNITION
7. STARTER MOTOR
8. H.T. COIL

MAN-043C 48