Scribd
Upload
423 views

Annexure - ESP Sizing Calculation

The document describes the sizing calculations and performance data for an electrostatic precipitator (ESP) for a 660MW power plant project. The ESP is designed to treat flue gas with up to 150°C temperature and 109 gm/Nm3 dust concentration. Based on the design criteria and gas flow rate, the required ESP size is calculated to be 6XFAA-10X45M-2X84160-2, which provides a specific collection area of 336 m2/m3/s under guarantee point conditions and 285.51 m2/m3/s under design point conditions, meeting the minimum required area of 240 m2/m3/s. The calculated migration velocity is 0.

Uploaded by

Swaraj Biswas
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
423 views

Annexure - ESP Sizing Calculation

The document describes the sizing calculations and performance data for an electrostatic precipitator (ESP) for a 660MW power plant project. The ESP is designed to treat flue gas with up to 150°C temperature and 109 gm/Nm3 dust concentration. Based on the design criteria and gas flow rate, the required ESP size is calculated to be 6XFAA-10X45M-2X84160-2, which provides a specific collection area of 336 m2/m3/s under guarantee point conditions and 285.51 m2/m3/s under design point conditions, meeting the minimum required area of 240 m2/m3/s. The calculated migration velocity is 0.

Uploaded by

Swaraj Biswas
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Annexure to ESP GA Drawing

PROJECT- WBPDCL SAGARDIGHI STAGE-II (1X660MW)

Electrostatic Precipitator sizing calculation & Performance data

INTRODUCTION:

When sizing the precipitator for this project, we have relied on our basic sizing technology and our wide
experience with collecting high resistive dust. In addition, we have utilized trends in test results available
from full scale precipitators.

1.0 DESIGN CRITERIA

The following design criteria form the basis for sizing and performance of precipitators.

1.1 ELECTROSTATIC PRECIPITATOR:

The required specific collection area (SCA) for the ESP is arrived at based on the expected performance
parameter viz. the migration velocity, using modified Deutsche formula. The formula with the design
philosophy is outlined under 3.0. Then total collecting area of the ESP is calculated using this SCA and
the flue gas flow volume at design condition.

The ESP size thus arrived at is checked for the minimum requirement of SCA.

Rev:00 / date: 28.05.2020 Page No:1/5


Annexure to ESP GA Drawing

PROJECT- WBPDCL SAGARDIGHI STAGE-II (1X660MW)

Electrostatic Precipitator sizing calculation & Performance data


1.2 FLUE GAS CRITERIA AT ESP INLET:

Sl. No. Description Unit Guarantee point Design Point


TMCR Worst BMCR Worst
Coal Coal
1. Boiler load MW 660 660
2. Gas flow rate to ESP (Wet) m³/s 972 1271
Nm3/sec 644.1 820.3
3. Gas temperature at ESP C 139 150
inlet
4. Dust concentration at inlet of ESP gm/Nm³ 100.2 109.0
(dry @ 6% O2)
5. Moisture content in flue gas % (Wt) 10.54 12.67

6. Minimum Specific Collection Area as m2/m3/s 240 240


per specification (400mm pitch)
7. Spacing between collecting electrodes mm 400 400

8. Number of series electrical fields out - One Nil


of operation
9. Required outlet dust concentration of mg/Nm³ 25 25
ESP at the above conditions (dry)
10 Required Collection Efficiency of % 99.975 99.977
ESP at the above conditions

2.0 THE SIZING PHILOSOPHY

A variant of the Deutsche Formula is used by us as the basis for precipitator sizing. We follow the
modified Deutsche formula

Efficiency = 1 - e- (Wk x A/Q)^0.5


Where
A = collection Area in m2
Q = Gas flow rate in m3/s
Wk = Sizing constant, m/s
the sizing constant ‘Wk’ is equal to the Deutsche migration velocity ‘W’.

For this project, from the size selected, we calculate a ‘Wk’ of not less than 24.58 cm/s and SCA of
285.51 m2/m3/sec corresponding to design point condition (with worst coal firing) with all fields in
service. Further, ‘Wk’ and SCA for Guarantee point condition (with worst coal firing) works out to be
20.47 cm/s and 336 m2/m3/s respectively. Thus, the selected precipitator of size 6XFAA - 10X45M -

Rev:00 / date: 28.05.2020 Page No:2/5


Annexure to ESP GA Drawing

PROJECT- WBPDCL SAGARDIGHI STAGE-II (1X660MW)

Electrostatic Precipitator sizing calculation & Performance data


2X84160-2 meets the tender specified minimum SCA value of 240 m2/m3/sec under the Guarantee point
and Design point condition.
Accordingly the selected precipitator of size 6XFAA - 10X45M - 2X84160-2 will achieve the guaranteed
performance.
3.1 CALCULATION OF Wk

At design point (Worst coal):

Specific collection area with all field in service, SCA = 285.51 m2/m3/s

Collection efficiency = 99.977 %.

Using the formula

- (Wk x SCA) 0.5


Efficiency = 1- e

(Note: SCA = A/Q)

Substituting the values we get

99.977 % = 1 - e- (Wk x 285.51)^0.5


Therefore Wk = 0.2458 m/s

At guarantee point (Worst coal):

Specific collection area with one field out of service condition, SCA = 336 m2/m3/s

Collection efficiency = 99.975 %.

Using the formula

- (Wk x SCA) 0.5


Efficiency = 1- e

(Note: SCA = A/Q)

Substituting the values we get

99.975 % = 1 - e- (Wk x 336)^0.5


Therefore Wk = 0.2047 m/s

Rev:00 / date: 28.05.2020 Page No:3/5


Annexure to ESP GA Drawing

PROJECT- WBPDCL SAGARDIGHI STAGE-II (1X660MW)

Electrostatic Precipitator sizing calculation & Performance data

3.2 ESP SIZE CALCULATION

The ESP Collection area provided with = SCA X Flow = 336 X 972= 326592 m2
one field in each pass out of service at
guarantee point condition.
The corresponding Collection area with all = SCA X Flow = 285.5075 X 1271= 362880 m2
field in service at design point condition
No. of ESPs per boiler as per tender =6
Min. Aspect ratio =2
Max. flue gas velocity = 0.8 m/s

Based on the above we arrive at the size of 6XFAA- 10X45M - 2X84160-2

Calculation of collection area for the selected ESP size:


1 ESP size 6 X FAA - 10 X 45M - 2 X 84160– 2
2 No. of ESPs 6
3 No. of fields along the flow 10
4 No. of bus sections 2
5 Length of one each field, Ln 4.5m
6 Height of field, Hn 16.0 m
7 Width of one bus section, Bn 8.4 m
8 Pitch of collecting electrode, p 400 mm
9 Collection area per field, F = Ln X Hn X 2 X Bn/p = 4.5X16.0 X 2 X 8.4/ 0.4
= 3024 m2
10 Total collection area per boiler with = F X total no. of fields = 3024X 6 X 2 X 10 = 362880 m2
all fields in service
11 Total collection area per boiler with = F X No. of fields in service = 3024 X 6 X 2 X (10-1)
one field out of service = 326592 m2

4.0 ESP DATA

DESCRIPTION UNIT VALUES


ESP size 6XFAA - 10X45M - 2X84160 - 2
No. of ESPs per boiler One with six passes
No. of fields in the direction of flow 10
Aspect ratio 2.81
2
Collection area at Guarantee point with m 326592
one field in each pass out of service
Collection area at Design point with all m2 362880
fields in service

Rev:00 / date: 28.05.2020 Page No:4/5


Annexure to ESP GA Drawing

PROJECT- WBPDCL SAGARDIGHI STAGE-II (1X660MW)

Electrostatic Precipitator sizing calculation & Performance data


Guarantee Point Design Point
Gas velocity m/s 0.6 0.79
Treatment time s 45 45
2 3
Specific collection area (SCA) as per m /m /s 240 240
tender
Specific collection area (SCA) provided m2/m3/s 285.51
with all fields in service
Specific collection area (SCA) provided m2/m3/s 336 ----
with one field out of service
Migration velocity m/s 0.2458 0.2047

Rev:00 / date: 28.05.2020 Page No:5/5

You might also like