Kaleido-Alto

Kaleido-Quad
Multi-Image Display Processor
Installation Manual
M791-4200-104
5 September 2008

Miranda
Technologies Inc.
3499 Douglas-B.-Floreani
St-Laurent, Québec, Canada H4S 1Y6
Tel. 514-333-1772
Fax 514-333-9828
www.miranda.com

© 2008 Miranda Technologies Inc.

Installation Manual

Safety Compliance Information

Safety Compliance

This equipment complies with:

- CSA C22.2 No. 60950-1-03 / Safety of Information Technology Equipment, Including Electrical Business Equipment.
- UL 60950-1 (1st Edition) / Safety of Information Technology Equipment, Including Electrical Business Equipment.
st
- IEC 60950-1 (1 Edition) Incorporating A1, A2, A3, A4, and A11/ Safety of Information Technology Equipment, Including
Electrical Business Equipment.

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all
servicing to qualified service personnel. Servicing should be done in a static-free environment.

Kaleido-Alto & Kaleido-Quad

 Installation Manual

Table of Contents

1 Kaleido-Alto & Kaleido-Quad ....................................................................................... 1

1.1 Introduction .............................................................................................................................................. 1
1.2 Kaleido-Alto Series: Supports up to 10 Video Inputs............................................................................... 1
1.3 Kaleido-Quad Series: Supports up to 4 Video Inputs .............................................................................. 3
2 Installation ..................................................................................................................... 5
2.1 Unpacking ................................................................................................................................................ 5
2.2 Mechanical Installation............................................................................................................................. 5
2.3 Power Connection.................................................................................................................................... 5
2.4 Signal and Control Connections .............................................................................................................. 5
2.4.1 HD-SDI Video Inputs ......................................................................................................................... 6
2.4.2 SD-SDI Video Inputs ......................................................................................................................... 7
2.4.3 Composite Video Inputs .................................................................................................................... 7
2.4.4 DVI Input............................................................................................................................................ 7
2.4.5 DVI Resolutions Supported with a KXI-DVI-Bridge Connected to the Kaleido’s HD-SDI Input ........ 8
2.4.6 Analog Audio Inputs (Optional Alto-SA Mezzanine with 10 or 4 Inputs) ........................................... 9
2.4.7 Digital Audio Input (Optional Alto-AES Mezzanine) .......................................................................... 9
2.4.8 PC Audio Input ................................................................................................................................ 10
2.4.9 Component Analog (RGBHV) Output.............................................................................................. 10
2.4.10 DVI Output....................................................................................................................................... 10
2.4.11 Audio Monitoring Output.................................................................................................................. 11
2.4.12 GPI Inputs /Outputs ......................................................................................................................... 11
2.4.13 Ethernet ........................................................................................................................................... 13
2.4.14 USB ................................................................................................................................................. 13
2.5 Dual power supplies (Optional).............................................................................................................. 13
2.6 Multiple Kaleido-Alto/Quad Installations ................................................................................................ 14
2.6.1 Ethernet Connection for use with KEdit........................................................................................... 14
2.6.2 Controlling Multiple Kaleido-Alto/Quad units from a Kaleido-RCP.................................................. 14
3 Operation ..................................................................................................................... 16
3.1 Powering Up........................................................................................................................................... 16
3.2 Front Panel Status LED ......................................................................................................................... 16
3.3 Startup and Preparation......................................................................................................................... 16
3.4 Software Installation............................................................................................................................... 16
4 Technical Specifications ............................................................................................ 17
4.1 Inputs ..................................................................................................................................................... 17
4.2 Outputs................................................................................................................................................... 18
4.3 Control.................................................................................................................................................... 19
4.4 Processing Performance........................................................................................................................ 20
4.5 Frame..................................................................................................................................................... 20
Annex – Kaleido Display Resolution .............................................................................. 21
Contact Us! ....................................................................................................................... 23

Kaleido-Alto & Kaleido-Quad

1 Kaleido-Alto & Kaleido-Quad

1.1 Introduction
The Kaleido-Alto and Kaleido-Quad multi-image processors can display multiple video inputs (up to 10 for the
Alto, up to 4 for the Quad) on a single high-resolution output. The Kaleido-Alto/Quad combines the display of
video windows, audio level meters, text identification labels, tallies and on-screen status indicators in a
convenient single-RU frame. Various models are offered to support SDI video, composite video or the auto-
detection of composite and SDI. Four stereo audio level meters can be displayed inside or outside each video
window. Audio sources can be extracted from the embedded audio inside the SDI signals, or input via optional
audio mezzanines providing 4 or 10 AES or Analog stereo input signals. A DVI input allows the insertion of an
external computer signal to fill the background of the video layout. Layouts can be created using the KEdit
layout editor software and applied to the Kaleido-Alto/Quad system afterward. Layouts and frequently-used
functions can be operated via the Kaleido-RCP or via a mouse/pointer interface. The Kaleido-Alto/Quad is an
ideal solution in areas where a limited number of signals need to be monitored with fine picture quality. Its
compact 1RU frame is a real asset in areas where space is restricted.

The Kaleido-Alto/Quad is available in several different models:

1.2 Kaleido-Alto Series: Supports up to 10 Video Inputs

Kaleido-Alto-HD
The Kaleido-Alto-HD is configured with 10 auto-detect HD/SD-SDI/Composite video inputs. Each input is
capable of displaying HD/SD-SDI and Composite video input in PAL, SECAM, NTSC or black-and-white
formats automatically.

Kaleido-Alto-AD
The Kaleido-Alto-AD is configured with 10 auto-detect SD-SDI/Composite video inputs. Each input is capable of
displaying SD-SDI with 525 or 625 lines and Composite video input in PAL, SECAM, NTSC or black-and-white
formats automatically.

Kaleido-Alto-A
The Kaleido-Alto-A offers 10 Composite inputs. Each input auto-detects PAL, SECAM, NTSC or black-and-
white formats.
Installation Manual

Kaleido-Alto Features
• Auto-sensing HD-SDI, SDI and Analog Composite inputs (10)
• High-quality DVI and RGBHV outputs with up to 1920 x 1080 pixel resolution (except Kaleido-Alto-A and
Kaleido-Alto-AD models, which are limited to 1280 x 1024)
• Embedded, AES and Analog audio level metering with monitoring outputs
• Source IDs, Tallies, clocks (time of day and up/down timers)
• Easy offline layout editing with full choice of window ratio (4:3 and 16:9) and position
• Aspect ratio markers
• Compact (1RU) frame
• Optional redundant power supply
• Optional, simple to use remote control panel

Kaleido-Alto Configuration
Here is a typical configuration for a Kaleido-Alto, in this case illustrating an Alto-AD.

Figure 1.1 Kaleido-Alto-AD configuration

2 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

1.3 Kaleido-Quad Series: Supports up to 4 Video Inputs

Kaleido-Quad-HD

The Kaleido-Quad-HD is configured with 4 auto-detect HD/SD-SDI/Composite video inputs. Each input is
capable of displaying HD/SD-SDI and Composite video input in PAL, SECAM , NTSC or black-and-white
formats seamlessly.

Kaleido-Quad-AD

The Kaleido-Quad-AD is configured with 4 auto-detect SD-SDI/Composite video inputs. Each input is capable
of displaying SD-SDI with 525 or 625 lines and Composite video input in PAL, SECAM, NTSC or black-and-
white formats seamlessly.

Kaleido-Quad Features

• Auto-sensing HD-SDI, SDI and Composite inputs (4)

• High quality DVI and RGBHV outputs with up to 1920 x 1080 pixel resolution
• Embedded, AES and Analog audio level metering with monitoring outputs
• Source IDs, Tallies, clocks (time of day and up/down timers)
• Easy offline layout editing with full choice of window ratio (4:3 and 16:9) and position
• Aspect ratio markers
• Compact (1RU) frame
• Optional redundant power supply
• Optional, simple to use remote control panel

Kaleido-Alto & Kaleido-Quad | 3

Installation Manual

Kaleido-Quad Configuration

Here is a block diagram showing a typical configuration for a Kaleido-Quad, in this case illustrating a Quad-AD
system.

Figure 1.2 Kaleido-Quad-AD configuration

4 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

2 Installation

2.1 Unpacking
Make sure the following items have been shipped with your Kaleido-Alto/Quad. If any of the following items are
missing, contact your distributor or Miranda Technologies Inc.

• Kaleido-Alto or Kaleido-Quad unit

• USB mouse
• AC power cord, and retainer clip
• CD with software

2.2 Mechanical Installation

Kaleido-Alto/Quad may be installed in a standard 19-inch rack, using the proper screws and washers ( not
included). The optional Kaleido-RCP Remote Control Panel may also be installed in a rack using the optional
mounting kit (order part #1229-1100-100).

For proper ventilation, make sure the front and side panel air vents are not blocked and the air filter is clean.

2.3 Power Connection

Connect the supplied AC power cord to the rear-panel AC receptacle, and secure it with the retainer clip
attached to the receptacle. The Kaleido-Alto/Quad includes a universal power supply for 110V and 220V
operation.

2.4 Signal and Control Connections

All inputs and outputs are located on the rear panel of the Kaleido-Alto/Quad. Signals and connector types are
listed and described below. The rear panel labels indicate the appropriate connection point for each signal.

Figure 2.4.1 Kaleido-Alto-AD/A rear panel

Figure 2.4.2 Kaleido-Alto-HD rear panel

Figure 2.4.3 Kaleido-Quad-HD/AD rear panel

The following chart summarizes the various inputs and outputs appearing on the rear panels of these units, and
is followed by a discussion of each of the connections.

Kaleido-Alto & Kaleido-Quad | 5

Installation Manual

Kaleido
Connector
Quad Alto Signal connections & communication ports
type
AD HD A AD HD
HD-SDI video inputs BNC
4 10 SD-SDI video inputs BNC
4 10
10 Composite video inputs BNC
1 1 1 1 1 DVI input DVI-D
4 or 4 or 4 or 4 or 4 or AES/EBU or stereo analog audio input (optional) DB-44S
10 10 10 10 10
1 1 1 1 1 PC audio input 3.5 mm jack
1 1 1 1 1 Component analog (RGBHV) output DE-15P
1 1 1 1 1 DVI output DVI-I
1 1 1 1 1 Audio monitoring output DE-15P
20 20 20 20 20 GPI inputs DB-44S
10 10 10 10 10 GPI outputs DB-44S
1 1 1 1 1 Ethernet communication RJ-45
1 1 1 1 1 RS-422 A port DE-9
1 1 1 1 1 RS-232 port DE-9
1 1 1 1 1 RS-422 B port DE-9
2 2 2 2 2 Mouse and Keyboard USB type A

Table 1: Signal connections

Note that one set of BNC connectors serves all video inputs except the DVI input. The Kaleido-Alto/Quad will
auto-detect the type of signal applied, and process it appropriately.

2.4.1 HD-SDI Video Inputs

These inputs must conform to the SMPTE 292M standard. The following input formats are supported:

Display Active Active Total Total Pixel Scan Frame Line Pixel Std.
Format Aspect Pixel Lines Pixels Lines Aspect Form. Rate Rate Rate (SMPTE)
Ratio Ratio (Hz) (KHz) (MHz)
1080i 59.94Hz 16:9 1920 1080i 2200 1125 SQR 2:1 29.97 33.72 74.18 274M
1080i 50Hz 16:9 1920 1080i 2376 1250 SQR 2:1 25 31.25 74.25 295M
720p 59.94Hz 16:9 1280 720 1650 750 SQR 1:1 59.94 44.96 74.18 296M
720p 50Hz 16:9 1280 720 1980 750 SQR 1:1 50 37.5 74.25 296M
1080p 29.97Hz 16:9 1920 1080 2200 1125 SQR 1:1 29.97 33.72 74.18 274M
1080p 23.98Hz 16:9 1920 1080 2750 1125 SQR 1:1 23.98 26.97 74.18 274M

Make sure the input cable has a maximum length of 100m (325') (Belden 1694) and that all serial digital video
connections are point-to-point. For instance, there must be a point-to-point connection between the IN BNC and
the source equipment. If a T-connector is used to connect other equipment, the maximum specified cable
length is no longer valid.

6 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

2.4.2 SD-SDI Video Inputs

The inputs are on BNC connectors and accept 4:2:2 serial digital video signals in either 525 or 625-line format.
These inputs must conform to the SMPTE 259M-C standard.

Make sure the input cable has a maximum length of 225m (730’ using Belden 1694A), and that all serial digital
video connections are point-to-point. For instance, there must be a point-to-point connection between the IN
BNC and the source equipment. If a T-connector is used to connect other equipment, the maximum specified
cable length is no longer valid.

2.4.3 Composite Video Inputs

The inputs are BNC connectors, internally terminated and accept NTSC, PAL, SECAM and monochrome
(B&W) video signals. NTSC-M signals must conform to the SMPTE 170M standard and PAL (625/50), PAL-M
(525/60) signals must conform to the ITU-R BT.470-6 standard.

2.4.4 DVI Input

A DVI signal may be connected to the Kaleido-Alto/Quad to provide a background image behind the monitoring
windows. Supported DVI signal resolutions are shown in the table 2 below

Note: To use a background image from a source connected through the DVI input, you must make sure that
the source computer and your Kaleido’s display screen are configured to the same resolution, since no scaling
will be applied to the DVI input signal.
Alternatively, a KXI-DVI-Bridge device can be connected upstream to the Kaleido-Alto/Quad in order to provide
a scaled background image. See section 2.4.5 “DVI Resolutions Supported with a KXI-DVI-Bridge Connected
to the Kaleido’s HD-SDI Input” for details.

Kaleido Scanning Line rate Frame rate

Quad Alto Resolution format (kHz) (Hz)
AD HD A AD HD (H x V)

X X X X X 800 x 600 Progressive 37.7/31.4 59.94 50

X X X X X 1024 x 768 Progressive 48.4/40.3 59.94 50

X X X X X 1280 x 768 Progressive 48.1/40.1 59.94 50

X X X X X 1280 x 1024 Progressive 64/53.3 59.94 50

X X X X X 1360 x 768 Progressive 47.6/39.8 59.94 50

X X X 1600 x 1200 Progressive 74,9/62.5 59.94 50

X X X 1920 x 1080 Progressive 69.5/62.5 59.94 50

Table 2 Supported DVI input signal resolutions

Note that the 1600X1200 and 1920X1080 formats apply only to selected models, and that special consideration
is required when using them. See the “Annex – Kaleido Display Resolution” for more information.

Kaleido-Alto & Kaleido-Quad | 7

Installation Manual

2.4.5 DVI Resolutions Supported with a KXI-DVI-Bridge Connected to the Kaleido’s

HD-SDI Input
With a KXI-DVI-Bridge device connected between a computer’s DVI output and the HD-SDI input of a Kaleido-
Alto-HD or Kaleido-Quad-HD, the following resolutions are supported.

Without dongle: DVI resolution HD-SDI output

1024x768 (XGA), 60 Hz
1280x1024 (SXGA), 60 Hz Suitable for graphic-type
1080i @ 29.97 Hz images with slow
1366x768 (WXGA), 60 Hz
motion.
1680x1050 (WSXGA+), 60 Hz

With dongle: DVI resolution HD-SDI output

1280x720, 50 Hz 720p, 50 Hz Best-quality
performance with video-
1280x720, 60 Hz 720p, 60 Hz
type computer-
1920x1080, 50 Hz 1080i, 50 Hz generated content. No
motion artifacts.
1920x1080, 60 Hz 1080i, 60 Hz

8 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

Note: The KXI-DVI-Bridge’s input can be static content (such as computer-generated text and static graphics)
to be scaled and merged against the layout background on the Kaleido. In this case the dongle is generally not
required. For the KXI-DVI-Bridge to process dynamic content (such as streaming video or computer-generated
animations), the dongle is required. Please refer to your KXI-DVI-Bridge User’s Manual for more information.

2.4.6 Analog Audio Inputs (Optional Alto-SA Mezzanine with 10 or 4 Inputs)

This option provides inputs for 10 or 4 channels of analog stereo audio. Two DB-44S connectors are available
on the Alto-SA mezzanine.

Connect balanced analog stereo audio signals to the audio input connectors. Each connector receives 5 stereo
inputs (refer to figure 2.4.4 below for connector pinout). For the 4-input audio version only inputs IN 1-4 are
available.

To facilitate cabling of the audio inputs, a terminal block adapter is available separately (Alto-TBA-AG). A Lexan
plate is provided to identify the terminal assignment for the input connectors. See figure 2.4.6 for plate
installation on the Alto-TBA-AG terminal block adapter.

Figure 2.4.4 Analog audio connector pinout

2.4.7 Digital Audio Input (Optional Alto-AES Mezzanine)

This option provides inputs for 10 or 4 channels of AES/EBU digital audio. A single DB-44S connector is
available on the Alto-AES mezzanine.

Connect AES balanced audio signals to the audio input connector. Signal must conform to AES3-1992/ANSI
S4.40-1992 standard. The DB-44 connector receives 10 inputs (refer to figure 2.4.5 below for connector
pinout). For the 4-input audio version only inputs IN 1-4 are available.

To facilitate cabling of the audio inputs, a terminal block adapter is available separately (Alto-TBA-AG). A Lexan
plate is provided to identify the terminals assignment for the input connectors. See figure 2.4.6 for Lexan plate
installation on the Alto-TBA-AG terminal block adapter.

Kaleido-Alto & Kaleido-Quad | 9

Installation Manual

Figure 2.4.6 Installing the Lexan plate on Alto-TBA-

AG
Figure 2.4.5 AES-EBU connector pinout

2.4.8 PC Audio Input

Connect a 3.5 mm audio jack to provide an analog stereo audio input coming from a personal computer. Note
that this audio signal is input at its nominal level, which is controlled by the originating computer. Make sure that
the level is within specifications (see section 4 “Technical Specifications”) by adjusting the level on the
originating computer.

2.4.9 Component Analog (RGBHV) Output

Analog progressive scan component video output (DE-15P connector). Connector pinout is shown in figure
2.4.7 below.

Figure 2.4.7 DE-15P connector pinout

2.4.10 DVI Output

Digital progressive scan component output (DVI digital connector), with resolutions as shown in the chart on
page 7 for the DVI input.

For optimum performance, good DVI cables should be used. For instance, cable model D-766 from Cable4PC
(www.cable4pc.com) is recommended.

10 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

2.4.11 Audio Monitoring Output

A DE-15P connector is provided to monitor one stereo audio channel, in both balanced AES3 and analog
formats. Refer to figure 2.4.8 for connector pinout.

Figure 2.4.8 Audio monitoring connector pinout

2.4.12 GPI Inputs /Outputs

The GPI input connector provides interfaces and processing to support 20 contact closure tally inputs and
provisions to support 10 outputs using DB-44S connectors. The connector pinout and circuit schematics are
shown in figure 2.4.9 and 2.4.10 below.

To facilitate cabling of the GPI inputs and outputs, a terminal block adapter is available separately (Alto-TBA-
AG). A double-sided Lexan plate is provided to identify the terminals assignment for both input and output
connectors. Place the Lexan plate as indicated in figure below, and install cables and plug the adapter into the
connector.

Figure 2.4.9 GPI Connector pinout

Kaleido-Alto & Kaleido-Quad | 11

Installation Manual

GPI input characteristics:

Signal: 20 short-to-ground inputs

Connector: DB-44S

GPI output characteristics:

Signal: 10 opto-isolated contact

closures
Connector: DB-44S
Characteristics:
• Max differential voltage: 12 VDC
• Max sink current: 70 mA
• Isolation voltage: 2500 VRMS

Figure 2.4.10 GPI I/O characteristics

RS-422 A
DE-9S connector for connecting remote control devices such as routers or the Kaleido-RCP (12V is supplied
through pin 5 to the Kaleido-RCP).

Figure 2.4.11 RS-422 A Connector pinout

RS-232
DE-9P connector to connect to router status information sources for tracking UMDs or inputting time code using
a device such as Miranda’s “Little Red”.

Figure 2.4.12 RS-232 Connector pinout

12 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

RS-422 B
DE-9S connector for connecting remote control devices such as routers.

Figure 2.4.13 RS-422 B Connector pinout

2.4.13 Ethernet
An RJ-45 connector for 10/100Base-T Ethernet interface connection to LAN/WAN networks using TCP-IP.

2.4.14 USB
Dual USB 1.0 ports used to connect a mouse (supplied) and keyboard to allow the user to operate the Kaleido-
Alto/Quad.
Note: Multi-function keyboards (i.e. with built-in USB ports, volume controls and other special buttons) are not
supported, so make sure to use a simple, basic USB keyboard.

2.5 Dual power supplies (Optional)

The Kaleido-Alto-HD and the Kaleido-Quad-HD/SD can be configured with dual power supplies. The figure
shows the location of the power supplies in the base configuration (single power supply) and the option dual-
supply configuration.

The user can associate a software Alarm with these power supplies in order to monitor their status from a
remote location via iControl.

Kaleido-Alto & Kaleido-Quad | 13

Installation Manual

2.6 Multiple Kaleido-Alto/Quad Installations

2.6.1 Ethernet Connection for use with KEdit

KEdit software is used to create layouts for the Kaleido-Alto/Quad. Each Kaleido-Alto/Quad can have layouts
created specifically for its application requirements. These layouts are created on a PC running KEdit software
(described in its own manual) and uploaded to the Kaleido-Alto/Quad via Ethernet, each Kaleido-Alto/Quad
having its own IP address.

Figure 2.5.1 Kaleido-Alto/Quads connected to an Ethernet network

2.6.2 Controlling Multiple Kaleido-Alto/Quad units from a Kaleido-RCP

Using the RS-422 A communication port allows up to 99 daisy-chained Kaleido-Alto/Quad frames to be

controlled using only one Kaleido-RCP, through the use of a multidrop cable. Figure 2.5.2 illustrates cabling
between the Kaleido-Alto/Quads and the Kaleido-RCP. Other products in the Kaleido family may be included,
as shown in the figure.

For this to work, the Kaleido-RCP must be able to send commands to a specific Kaleido-Alto/Quad in the daisy-
chain. This is accomplished by assigning an identification code to each of the Kaleido-Alto/Quad frames.

By default, Kaleido-RCP will send instructions using RS-422 protocol to ID 1. This means that a system
comprised of only one Kaleido-Alto frame will work out of the box as each frame’s default ID is also set to 1.
However, for applications where more than one Kaleido-Alto/Quad frame is used, you will need to assign a
unique ID number to each of them. Consult the Kaleido-Alto/Quad/Quad-Dual User’s Manual for details.

As indicated in the figure below, a 120 Ω termination resistor must be installed on the cable connector on the
last Kaleido-Alto/Quad frame in the daisy-chain. In a point-to-point connection, it must be installed on the
receiver; for a more-than-one Kaleido-Alto/Quad frame connection (called a “multidrop connection”), it must be
installed on receiver and driver. For more details, consult Miranda Application Note #229-99T00-101.

14 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

RS-422 Multi-drop Cable Example

Notes:

1: For pins 2/7 and 3/8, using Belden 8162 or similar is recommended, 24AWG. 4: As illustrated, the Tango has Tx and Rx
2 Twisted Pairs individually shielded, both GND and the Overall foil connected to pin 1 signals located at different pins than other
Kaleido products.
2: For PINS 4 and 5, wires should be 20AWG.
3: As illustrated, it is strongly recommended to get 12V required for the RCP from
an external DC supply or AC/DC adaptor. It shall deliver 3W or more (250mA
or more). The distance between the supply and the RCP should be the
shortest possible.
Device #1: Device #2: Device #4: Device #n:
Kaleido-Classic, Kaleido-Classic, Kaleido-Classic, Kaleido-Classic,
Kaleido-K2, Kaleido-K2, Device #3: Kaleido-K2, Kaleido-K2,
Kaleido-Alto Kaleido-Alto Tango Kaleido-Alto Kaleido-Alto
Kaleido-RCP or Kaleido-Quad or Kaleido-Quad or Kaleido-Quad or Kaleido-Quad

DE9-M DE9-M DE9-M DE9-M DE9-M DE9-M

Pair 1 Pair 3 Pair 5 Pair 7
Tx- 2 2 2 8 2 2

120Ω
Tx+ 7 7 7 3 7 7
GND shield GND shield GND shield GND shield

(overall shield) (overall shield) (overall shield) (overall shield)

1 1 1 1 1 1
Foil Foil Foil Foil

GND shield GND shield GND shield GND shield

Rx+ 3 3 3 7 3 3

120Ω
Rx- 8 8 8 2 8 8
Pair 2 Pair 4 Pair 6 Pair 8
GND 4 External DC
power supply
+12V 5 or AC/DC
adaptor

Figure 2.5.2 Kaleido Alto/Kaleido-RCP interconnection for cascading multiple frames

Kaleido-Alto & Kaleido-Quad | 15

Installation Manual

3 Operation
The Kaleido-Alto has no local controls beyond the power switch. Operational concerns are outlined here, but for
detailed operating instructions, see the Kaleido-Alto/Quad/Quad-Dual User’s Manual. Periodically, new
software versions may be uploaded using “live update” through the Ethernet connection.

3.1 Powering Up
The power switch is located on the rear panel of the Kaleido-Alto/Quad, just above the power cord. Plug the
cord into an appropriate AC power supply, and set the switch to ON ( I ). If you have just switched the unit
OFF ( 0 ), always wait a few seconds before turning it ON again to ensure proper startup procedure.

3.2 Front Panel Status LED

There is a system status LED mounted on the front panel of the Kaleido-Alto/Quad. This LED gives operational
status when powering up the unit, and signals any malfunction of the unit. Note that this LED does not report on
the status of the inputs connected at the back.

Figure 3.1 Front panel status LED (same location on Alto and Quad)

At startup, the LED will briefly light up red, then flashing yellow. After 10 to 15 seconds the LED lights up green
to indicate normal system operation. Other states may be:

Yellow (continuous): System boot-up problem or live update not completed correctly
Red (continuous): System failure

3.3 Startup and Preparation

The Kaleido-Alto is shipped with the current version of the software installed, and configured to auto-start when
the system is powered on. Upon initial startup, the system will present the default monitoring window at its
output. Upon subsequent start-ups, the system will present the last monitoring window that was present before
shut-down. See the Kaleido-Alto/Quad/Quad-Dual User’s Manual for detailed instructions on how to operate the
software.

3.4 Software Installation

In case of recovery from a system failure, or when a software update is available, it may be necessary to install
the Kaleido-Alto/Quad/Quad-Dual software or the KEdit layout editor. All the necessary software is delivered on
a CD included in the product package, or downloaded from Miranda’s web site. As the Kaleido-Alto/Quad unit
does not have a CD drive, it is necessary to install the software from a remote computer through a network
connection. Installation of the software is detailed in a ReadMe file included with the update.

16 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

4 Technical Specifications

4.1 Inputs
INPUTS Kaleido ALTO QUAD
Model HD AD A HD AD
Digital Video Input (HD-SDI) 10 NA NA 4 NA
Signal SMPTE 292M
Cable Length 100m (325') (Belden 1694)
Return Loss 15dB up to 1.5Gbps
Impedance 75Ω
Connector BNC

Digital Video Input (SD-SDI) 10 10 NA 4 4

Signal 4:2:2 SMPTE 272M, 259M-C
Cable Length 225 m (Belden 1694A)
Return Loss 15dB up to 270 MHz
Impedance 75Ω
Connector BNC

Composite Video Input 10 10 10 4 4

Signal NTSC SMPTE 170M, PAL, PAL-M, SECAM, B&W
Return Loss 35dB up to 5.75MHz
Quantization 8 bits
Impedance 75Ω
Connector BNC

DVI-D Input (High res) 1 NA NA 1 1

Signal Digital DVI
Cable Length 3.6 m (12’) with Altinex CB4012DV
Resolution 800x600 to 1920X1080 w/56LB at 50/59.94 Hz
(see table 2 on page 7 for details)
Connector DVI

DVI-D Input (Limited res) NA 1 1 NA NA

Signal Digital DVI
Cable Length 3.6 m (12’) with Altinex CB4012DV
Resolution 800x600 to 1280X1024 at 50/59.94 Hz
(see table 2 on page 7 for details)
Connector DVI

HD Embedded Audio Input 10 NA NA 4 NA

Signal SMPTE 292M
Bit Resolution 20-24 bits
Sampling Rate 48 kHz synchronous

SD Embedded Audio Input 10 10 NA 4 4

Signal SMPTE-272M
Bit Resolution 20 bits
Sampling Rate 48 kHz synchronous
…..continued

Kaleido-Alto & Kaleido-Quad | 17

Installation Manual

INPUTS Kaleido ALTO QUAD

(continued) Model HD AD A HD AD
PC Audio 1 1 1 1 1
Signal Analog Stereo, source level adjustable
Impedance 16kΩ
Max. level 2V peak to peak
Sampling Rate 48 kHz free run
Bit Resolution 20 bits
Connector Stereo audio jack 3.5 mm

4.2 Outputs

OUTPUTS Kaleido ALTO QUAD

Model HD AD A HD AD
RGBHV Progressive Output (High Res) 1 NA NA 1 1
Resolution: 800x600 to 1920X1080 w/56LB at 50/59.94
Hz
(see table 2 on page 7 for details)
H Frequency From 31.4 kHz to 74.9 kHz
V Frequency 50/59.94 Hz
Level 0.7 or 1.0 Vp-p (selectable software)
Cable Length Short, Medium, Long
Connector DE-15S

RGBHV Progressive Output (Limited res) NA 1 1 NA NA

Resolution 800x600 to 1280X1024 at 50/59.94 Hz
(see table 2 on page 7 for details)
H Frequency From 31.4 kHz to 74.9 kHz
V Frequency 50/59.94 Hz
Level 0.7 or 1.0 Vp-p (selectable software)
Cable Length Short, Medium, Long
Connector DE-15S

DVI-I Output (high resolution) 1 NA NA 1 1

Signal Digital DVI
Cable Length 3.6 m (12’) with Altinex CB4012DV
Resolution 800x600 to 1920X1080 w/56LB at
50/59.94 Hz
(see table 2 on page 7 for details)
Connector DVI

DVI-I Output (limited resolution) 1 NA NA 1 1

Signal Digital DVI
Cable Length 3.6 m (12’) with Altinex CB4012DV
Resolution 800x600 to 1280X1024 at 50/59.94 Hz
(see table 2 on page 7 for details)
Connector DVI

…..continued

18 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

OUTPUTS Kaleido ALTO QUAD

(continued) Model HD AD A HD AD
AES Audio Output 1 1 1 1 1
Signal AES3
Quantization 20 bits
Impedance 110Ω
Attenuation Minimum level 0 dBFs (step 6 dBFs)
Sampling Rate 48 KHz
Connector DE-15S

Analog Stereo Audio Output 1 1 1 1 1

Signal 1 stereo balanced output
Quantization 20 bits (minimum)
Impedance <50Ω
Level +24 dBu, adjustable level (step 6 dBu)
SNR 98dB (A weighting) up to 20-22kHz
THD+N 80dB @ 1kHz
Frequency response +/- 0.3dB
Connector DE-15S

4.3 Control

CONTROL All models

GPI Inputs
Contact closure GND
Total cable length 200’
Minimum pulse duration 100 ms
Connector DB-44S

GPI Outputs
Max. voltage 12 VDC differential voltage
Cable length 100 ms
Connector DB-44S

RS-232
Signal RS-232 (EIA/TIA-232)
Baud rate 9600 BPS, according to application
Connector DE-9P

RS-422 A
Signal RS-422 (SMPTE 207M, EBU-3245)
(a 12V power supply on pin 5 is provided for the Kaleido-RCP)
Data rate 38400 BPS, according to application
Connector DE-9S

…..continued

Kaleido-Alto & Kaleido-Quad | 19

Installation Manual

CONTROL
All Models
(continued)
RS-422 B
Signal RS-422 (SMPTE 207M, EBU-3245)
Data rate 38400 BPS, according to application
Connector DE-9S

Ethernet
Signal 10Base-T, 100Base-T (IEEE 802.3)
Connector RJ-45

USB
Signal USB ver. 1.0
Connector USB double type receptacle A

4.4 Processing Performance

PROCESSING PERFORMANCE All models
Signal path 8 bits
Quantization 24 bits on RGBVH output
Graphic 18 bits on RGB
Maximum video processing delay to DVI output 60 Hz: less than 34 ms
50 Hz: less than 44 ms

4.5 Frame
FRAME
Kaleido-Alto-AD/A
Voltage 100-240 VAC
Power 90 W
Dimensions 1RU (19-inch rack) X 19.25 in (490 mm) deep
Weight 8.1lbs (3.7 kg)
Operating temperature 0-40° C

Kaleido-Alto-HD, Kaleido-Quad-HD/AD
Voltage 100-240 VAC
Power 110 W (Kaleido-Alto-HD)
Power 50 W (Kaleido-Quad-HD/AD)
Dimensions 1RU (19-inch rack) X 19.25 in (490mm) deep
Weight 10lbs (4.5 kg)
Operating temperature 0-40° C DB-44S

20 | Kaleido-Alto & Kaleido-Quad

 Installation Manual

Annex – Kaleido Display Resolution

The Kaleido-Alto/Quad displays all the elements of its layout in a frame whose maximum vertical resolution is
1024 pixels. However, the RGBHV output from all versions of the Kaleido-Alto and the Kaleido-Quad can drive
displays with greater vertical resolution, provided they are equipped with an appropriate hardware version (see
the chart below). In particular, displays operating at 1920x1080 and 1600x1200 can be used with these Kaleido
models.

1600 x 1200 resolution:

To drive a 1600x1200 display, the Kaleido layout must be created at 1600x1024 pixels. In KEdit, you must
generate a 25 x 16 display aspect ratio. When this layout is shown on the display, 88 lines on top and bottom
will be displayed in black.

1920 x 1080 resolution:

To drive a 1920x1080 display, the Kaleido layout must be created at 1920x1024 pixels. In KEdit, you must
generate a 15 x 8 display aspect ratio. When this layout is shown on the display, 28 lines on top and bottom will
be displayed in black (see figure A1).

Figure A1 Kaleido-Alto output on a 1920x1080 display showing black bars at the top and bottom

A feature of Kaleido-Alto/Quad is the ability to replace the internally-generated background in the layout with
images from an external source, via the DVI input. In this case, it is appropriate to select a DVI background
source to match the display in use, i.e. 1600x1200 or 1920x1080. The background will occupy the entire
display screen, and the Kaleido-generated elements will be keyed into the vertically-centered 1024-line portion
of the screen, with no visible indication of any boundaries within the image (see figure A2).

Three sets of alternative “color keys” can be used by the background application. For example, in the case of
integration with iControl Web, the background uses (255 blue, 255 green and 0 red).

Kaleido-Alto & Kaleido-Quad | 21

Installation Manual

Figure A2 Kaleido-Quad output on a 1920x1080 display showing the DVI background occupying the entire
display with the Kaleido layout elements keyed in.

Higher-resolution output support

Here is a chart of Kaleido-Alto/Quad models and hardware revisions that will support output at 1920x1080 and
1600x1200 resolution:

Kaleido Models Hardware revision: Resolution higher than 1024 lines

200 = v200 base version (i.e. 1920 x 1080 and 1600 x 1200)
200* = v200 enhanced version displayed in letter box format)
Kaleido-Alto-A 100 - 200 Not Supported
200* Supported
Kaleido-Alto-D 100 - 200 Not Supported
200* Supported
Kaleido-Alto-AD 100 - 200 Not Supported
200* Supported
Kaleido-Alto-A2 300 and higher Supported
Kaleido-Alto-AD2 300 and higher Supported
Kaleido-Alto-HD 300 and higher Supported
Kaleido-Quad-HD 300 and higher Supported
Kaleido-Quad-AD 300 and higher Supported

22 | Kaleido-Alto & Kaleido-Quad

Contact Us!

Miranda Technical Support

For technical assistance, please contact the Miranda Technical Support centre nearest you:

Americas Asia
Office hours: 9:00 a.m. – 9:00 p.m. (EST) Office hours: 9:00 a.m. – 5:00 p.m. (GMT+8)
Telephone: +1-800-224-7882 Telephone: +852-2539-6987
Fax: +1-514-335-1614 Fax: +852-2539-0804
E-mail: [email protected] E-mail: [email protected]

Europe, Middle East, Africa, UK China

Office hours: 9:00 a.m. – 6:00 p.m. (GMT) Telephone: +86-10-5873-1814
Telephone: +44 (0) 1491 820222 E-mail: [email protected]
Fax: +44 (0) 1491 820002
E-mail: [email protected]

France
Office hours: 9:00 a.m. – 5:00 p.m. (GMT+1)
Telephone: +33 1 55 86 87 88
Fax: +33 1 55 86 00 29
E-mail: [email protected]

Corporate Head Office

Miranda Technologies Inc.

3499 Douglas-B.-Floreani, St-Laurent, Quebec, Canada H4S 1Y6
Telephone: 514-333-1772
Fax: 514-333-9828
Web: www.miranda.com