ORDER NO.

RRV2054

STEREO CD CASSETTE DECK RECEIVER

XR-A770
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type Power Requirement Remarks
XR-A770
MYXJ AC220-230V
NVXJ AC230V

CONTENTS
1. SAFETY INFORMATION ...................................... 2 7. GENERAL INFORMATION ............................... 55
2. EXPLODED VIEWS AND PARTS LIST ................ 3 7.1 PARTS ......................................................... 55
3. SCHEMATIC DIAGRAM ..................................... 14 7.1.1 IC ......................................................... 55
4. PCB CONNECTION DIAGRAM .......................... 31 7.1.2 DISPLAY .............................................. 61
5. PCB PARTS LIST ............................................... 44 7.2 DISASSEMBLY ........................................... 63
6. ADJUSTMENT .................................................... 49 7.3 BLOCK DIAGRAM ....................................... 66
8. PANEL FACILITIES AND SPECIFICATIONS .... 68

PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER ELECTRONIC CORPORATION 1998
T – ZZK NOV. 1998 Printed in Japan
XR-A770

1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.

IMPORTANT
LABEL CHECK THIS PIONEER APPARATUS CONTAINS
LASER OF CLASS 1.
NVXJ Type
SERVICING OPERATION OF THE APPARATUS
SHOULD BE DONE BY A SPECIALLY
INSTRUCTED PERSON.

LASER DIODE CHARACTERISTICS

MAXIMUM OUTPUT POWER: 1.3 mW
WAVELENGTH: 790 nm ± 25 nm

MYXJ Type

MYXJ Type

Additional Laser Caution

1. Laser Interlock Mechanism
The position of the switch (S8501) for detecting loading
state is detected by the system microprocessor, and
the design prevents laser diode oscillation when the
switch (S8501) is pressed physically.
Thus, the interlock will no longer function if the switch (S8501)
is released physically and deliberatery.
The interlock also does not function in the test mode ∗.
Printed on the Rear Panel Laser diode oscillation will continue, if pin 62 of
LA9240ML (IC8101) on the CD ASSY mounted on the
$M Loading Mechanism assembly is connected to GND,
or else the terminals of Q8101 are shorted to each other
(fault condition).

2. When the cover is opened, close viewing of the objective

lens with the naked eye will cause exposure to a Class
1 laser beam.

∗ : Refer to page 54.

2
 XR-A770

2. EXPLODED VIEWS AND PARTS LIST

NOTES: • Parts marked by "NSP" and can not be supplied.
• The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Screws adjacent to mark on the product are used for disassembly.
4
2.1 PACKING NVXJ Type Only
9(1/2) MYXJ RE
W
OP

YA
LP
PE

SI
EL
S

XU
SS

A
AB
.P
LO

CS
V

CF

ID
S
EK

CS

TA
EP
ER
OA

ID
RA
K

CS

M
G
ID

P
RA
EL
C

Type Only
AR
DN
MO
TS
ITA ER
NO OM
ET
C
NO
M RT
NO LO
O NU
TI
UC
AB X-
DN 52
0R

5 12

2 17
7 13 13 15
14 MYXJ 9
1 Type Only 18
8(1/2)
19
3
9(2/2)
MYXJ
6 11 Type Only
MYXJ Type Only

16
8(2/2)

10
(1) PACKING PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
1 FM Antenna ADH7005 10 Packing Case See Contrast table (2)
2 Operating Instructions XRE3014 11 Packing Sheet AHG7049
(English/French) 12 Fuse (T5A) See Contrast table (2)
3 AM Loop Antenna XTB3001 13 Power Cord See Contrast table (2)
4 Remote Control Unit XZN3007 NSP 14 Polyethylene Bag See Contrast table (2)
(CU-XR049)
15 Operating Instructions XRE3016
5 Battery Cover AZA7204 (English/French/German/Italian/Dutch/
NSP 6 Dry Cell Battery (R6P, AA) VEM-013 Swedish/Spanish/Portuguese/Chinese)
7 Polyethylene Bag Z21-038 NSP 16 Door Spacer XHG3002
(0.03 × 230 × 340) NSP 17 Warranty Card ARY7022
8 Front Pad See Contrast table (2)
18 Operating Instructions See Contrast table (2)
9 Rear Pad See Contrast table (2) 19 Operating Instructions See Contrast table (2)

(2) CONTRAST TABLE

XR-A770/MYXJ and NVXJ are constructed the same except for the following :
Part No.
Mark No. Symbol and Description XR-A770 XR-A770 Remarks
/MYXJ /NVXJ
8 Front Pad XHA3005 XHA3009
9 Rear Pad XHA3006 XHA3010
10 Packing Case XHD3050 XHD3070
12 Fuse (T5A) Not used AEK1016
13 Power Cord ADG1154 ADG1156

NSP 14 Polyethylene Bag AHG7033 Not used

18 Operating Instructions (Italian/German/Dutch) XRC3003 Not used
19 Operating Instructions XRC3004 Not used
(Portuguese/Swedish/Spanish)

3
XR-A770

2.2 EXTERIOR (1/2)

15
15
8

11

Note :
Hook Tray cap on top of loading tray and then 11
insert the bottom three hooks.

Note :
Attatch on the same numbers × three.
12 9
Refer to
"2.5 $M MECHANISM CD".
2
12
11

6
9
16
18 1
17

10

13

18
7 3

14
3

4
 XR-A770

• EXTERIOR (1/2) PARTS LIST

Mark No. Description Part No.
1 22P F.F.C/30V XDD3018
NSP 2 $M Mechanism CD XXA3006
3 Volume Knob XAA3005
4 FL Cover A XAK3026
5 FL Cover B XAK3036

6 Tray Cap XZN3047

7 Display Panel XAK3049
8 Bonnet Case XZN3040
9 Screw BPZ30P100FZK
10 Pioneer Badge XZN3049

11 Screw VBT30P080FZK
12 Disc Label XAX3127
13 Jog Knob Assy XXG3023
14 Bass Knob XAB3005
15 Screw BCZ30P080FZK

NSP 16 Cord Stopper DNF1128

17 Push Rivet AEC7138
18 Cushion Rubber XEB3002

5
XR-A770

2.3 EXTERIOR (2/2)

27

19
27
18

1
35
13 20
16
19
d

a
b

40
c b a

c
a
b
a

a 38 28

a
19
a
30

b
34 28

33
36
12
b
23 MYXJ Type only
39 41
3 NVXJ
43 Type only

2
19
21 19 22
4 24
11

29 25

24
7 11 24
24

5 9 24
22

24
10
14
19 19 19
17
MYXJ
Type only
15
42

NVXJ
Type only

19

8 26

Refer to
"2.4 FRONT PANEL SECTION".

6
 XR-A770

(1) EXTERIOR (2/2) PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.
1 AF Assy XWZ3120 21 Screw ASZ40P060FMC
2 SECONDARY Assy XWZ3121 22 Binder ZCA-SKB90BK
3 PRIMARY Assy XWZ3152 23 Earth Plate XNG3015
4 FM/AM TUNER MODULE AXQ7068 24 Screw BPZ30P100FZK
5 Power Transformer (T1) XTS3018 25 Screw BBZ30P300FMC

6 ••••• NSP 26 Name Label See Contrast table (2)

7 Fuse (FU1 : T4A) AEK1060 27 Screw BBZ30P060FMC
NSP 8 Chassis XNA3001 28 Screw IBZ30P135FMC
9 DC Fan Motor AXM7003 29 SUB TRANS Assy XWZ3139
10 Fan Plate ANG7153 30 REAR AMP Assy XWZ3122

11 PCB Bracket XNG3006 31 •••••

12 Ceramic Capacitor CKPUYB102K50 32 •••••
13 Heat Sink XNH3004 33 H.S.Bracket XNG3007
14 Wire Clip A XEC3003 34 FET Bracket XNG3009
15 Rear Panel XNC3012 35 H.S.Support XNG3014

16 Cord Stopper DNF1128 36 Wire Clip B XEC3004

NSP 17 SUPPORT Assy XNP3009 37 •••••
18 Screw BBZ30P140FMC 38 Mica Sheet XEE3002
19 Screw VBZ30P080FZK 39 Locking Spacer XEC3009
NSP 20 Tweeter Cover XAK3069 40 Card Spacer XEC3008

41 Caution Label HE See Contrast table (2)

42 Caution Label See Contrast table (2)
43 Caution Label See Contrast table (2)

(2) CONTRAST TABLE

XR-A770/MYXJ and NVXJ are constructed the same except for the following :
Part No.
Mark No. Symbol and Description XR-A770 XR-A770 Remarks
/MYXJ /NVXJ
NSP 26 Name Label Not used XAL3012
41 Caution Label HE PRW1233 Not used
42 Caution Label VRW1094 Not used
43 Caution Label Not used PRW1018

7
XR-A770

2.4 FRONT PANEL SECTION

17
17
6

26 7 17
1
A
23

15 25
8
32 34(1/2) 34(2/2)
18 24
35
36
21

13 37
20

19 17 A

10
16 17
30 5
33 21 46 9

14
27
12
17 Refer to
"2.7 MECHANISM UNIT".
31 6
28

38
17
40
42

44 45
43

8
 XR-A770

• FRONT PANEL SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.
1 DISPLAY Assy XWZ3123 26 CD Lens XZN3037
2 CD SW LED Assy XWZ3131 27 Deck Lens L XZN3035
3 SUB DISPLAY Assy XWZ3112 28 Deck Lens R XZN3036
4 ••••• 29 •••••
NSP 5 Cord With Plug DE007VE0 30 Door Pocket L XZN3013

6 Flexible Cable 14P XDD3011 31 Door Pocket R XZN3015

7 Flexible Cable 19P XDD3009 32 Front Panel A XZN3011
8 Flexible Cable 38P XDD3004 33 Sub Panel A XZN3041
9 Connector Assy 3P XDE3013 34 Power Button XZN3022
10 Connector Assy 5P XDE3014 35 Play Button XZN3024

11 ••••• 36 S.C. Button XZN3025

12 Mechanism Unit XYM3003 37 TIMER Button XZN3029
13 Door Spring L XBH3001 38 Sub Buttun XAD3012
14 Door Spring R XBH3002 39 •••••
15 Latch Spring L ABH7130 40 Diffusion Sheet XAK3035

16 Latch Spring R ABH7131 41 •••••

17 Screw BPZ30P100FZK 42 Button Lens XAK3043
18 Latch Mold L XMR3001 NSP 43 Front Panel Assy B XXG3026
19 Latch Mold R XMR3002 44 Sub Panel B XZN3052
NSP 20 Jog Lens XAK3025 45 Front Panel B XZN3050

21 Damper Assy AXA7052 46 Binder ZCA-SKB90BK

22 •••••
NSP 23 Front Panel Assy XXG3016
24 Function Button XZN3020
25 CD Button XZN3018

9
XR-A770

2.5 $M MECHANISM CD
8 Refer to "2.6 SERVO MECHANISM ASSY".
21 25
7

22

14

24
13
23

11
1

2 5
12 26

15

29 19 27
18
28
29 6
16

10 17

29

3
30

29

29
29

29 9
29

29
10
 XR-A770

2.6 SERVO MECHANISM ASSY

• $M MECHANISM CD PARTS LIST 1

9
Mark No. Description Part No. 7

1 MOTOR Assy AWZ8428 9

NSP 2 SW Assy AWZ8429 9
3 CD Assy XWZ3141
4 •••••
5 Servo Spring ABH7126 9

6 Belt AEB7072
7 Clamp Magnet AMF7001
8 Yoke ANB7067
9 Mecha Base ANW7125
10 Loading Tray ANW7088
4
11 Servo Base ANW7089
12 Rotary Tray ANW7113
13 Clamper ANW7091
14 Clamper Holder ANW7092
15 Main Cam ANW7093
5
16 Gear Pully ANW7094
17 Lock Lever ANW7095
18 Planet Gear ANW7096 8
19 Actuater ANW7097
20 •••••

21 15P F.F.C/30V ADD7038

22 Connector Assy (6P) ADE7010 6
23 Float Rubber A AEB7063
24 Float Rubber B AEB7066
25 Servo Mechanism Assy AXA7039

26 Screw IPZ30P080FMC
27 Carriage Motor VXM1033
28 Motor Pulley PNW1634
29 Ha Narl GEM1016
30 Cushion Rubber XEB3003 3

10
2

• SERVO MECHANISM ASSY PARTS LIST

Mark No. Description Part No.
1 Servo Mechanism AXA7039
2 SPINDLE MOTOR Assy AEA7009
3 SLEAD MOTOR Assy AEA7010
4 Gear A AEA7013
5 Gear B AEA7014

6 Screw AEA7015
7 Screw AEA7016
8 Screw AEA7017
9 Screw AEA7018
10 Leaf Switch AEA7011

11
XR-A770

2.7 MECHANISM UNIT

4 Mech. ΙΙ
Only
7

Mech. Ι
Only

Mech. ΙΙ

Mech. Ι

9
Mech. ΙΙ
Mech. Ι Only
10
12

13
1

2 Mech. ΙΙ

12
 XR-A770

5
6

11

• MECHANISM UNIT PARTS LIST

Mark No. Description Part No.
1 Plate HD BLK (Mech. Ι) F513-819
2 Plate HD BLK (Mech. ΙΙ) F513-811
3 Motor Main BLK (Mech. ΙΙ only) F525-324
4 PCB Control BLK F567-621
5 Clutch Assy BLK F522-037

6 Main Belt FF17G-31

7 Joint Belt 113 (Mech. ΙΙ only) FF19D-21
8 Clutch Assy BLK F522-045
9 Roller Pinch BLK R F514-129
10 Roller Pinch BLK L F514-130

11 F/R Belt FF18W-12

12 Plate Base BLK F512-127
13 Plate Base BLK F512-128

13
 1 2 3 4
XR-A770

3. SCHEMATIC DIAGRAM
3.1 OVERALL WIRING DIAGRAM
A SERVO MECHANISM ASSY (AXA7039)

CN8001 CN8002

A B
FM/AM CD ASSY(XWZ3141)
TUNER MODULE
(AXQ7068)

E E 1/3 E 3/3
AF ASSY
(XWZ3120)

I
DISPLAY ASSY
(XWZ3123)

D
DECK MECHA

K SUB DISPLAY ASSY

(XWZ3112)

14
1 2 3 4
 5 6 7 8
XR-A770

Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
REAR AMP ASSY
C D SW ASSY
(AWZ8429) L (XWZ3122) A
MOTOR
ASSY
(AWZ8428)

CN8003

G
PRIMARY
F ASSY
(XWZ3152)
SECONDARY
ASSY
(XWZ3121)
C

H SUB TRANS
ASSY
(XWZ3139)

J CD SW LED
ASSY
D

(XWZ3131)

15
5 6 7 8
 1 2 3 4
XR-A770

3.2 FM/AM TUNER MODULE

A MIX AMP

RF AMP

OSC

BUFFER

IF AMP

FM +B SW

AM RF TUNING BLOCK

PLL

FM/AM TUNER MODULE

D
A (AXQ7068)

16 A
1 2 3 4
5 6 7 8
XR-A770

CN3051
AF AMP

E 2/3
AF AMP

REGULATOR

5 6 7
A
8
17
 1 2 3 4
XR-A770

3.3 CD, MOTOR and SW ASSEMBLIES

R8123
56k

B CD ASSY
(XWZ3141)

C MOTOR ASSY
(AWZ8428)
CARRIAGE MOTOR

J8502
D20PWW0405E
SERVO MECHANISM ASSY AXA7039

18 B C
1 2 3 4
 5 6 7 8
XR-A770

Note: The encircled numbers

denote measuring point in the
1 2 schematic diagram. A
1 CN8005- Pin 1 :
PLAY MODE (RF)
H : 500nsec/div
1.8Vp-p

100/10
C8371
VREF

2 CN8005- Pin 2 :
TEST MODE,
Tracking Open(TRER)

0.047
YB H : 5msec/div
C8308
1000p 1.0Vp-p
C8307 VREF
1000p
YB

L8371 47µH
VREF:CN8005- Pin3
B

CN1052
E 2/3
C8256 0.1
C8255 0.1
C

2SB1237X 2SB1237X

C8257
0.047

0.1

2SD1858X 2SD1858X

D D

SW ASSY
J8502 (AWZ8429)

5 6 7
B D 8
19
 1 2 3 4
XR-A770

3.4 AF ASSY (1/3)

A

E 1/3 (REC) (REC)

AF ASSY
(PB)
(XWZ3120)
22k
22k

(PB)
(REC)
(REC)

B (PB)
: DECK PB SIGNAL ROUTE
(REC)
: DECK REC SIGNAL ROUTE
(REC)

(REC) 47p

C2323
0.022

0.022
(REC)
(PB) 47p
47p
(PB)

47p
(PB)
(PB)

220k
33k

33k
220k

0.01

20 E 1/3 1 2 3 4
 5 6 7 8
XR-A770

IC2101(2/2)
BA4558F–HT
A

(PB) IC2101(1/2)
BA4558F–HT

(PB) (PB)

(PB)

E 2/3
(PB)

(PB)
(PB)

(REC)

(REC)
(REC)
(REC) B

22k
(REC)

22k

C
E 2/3

E 2/3
D

5 6 7
E 1/38
21
 1 2 3 4
XR-A770
3.5 AF ASSY (2/3) B CN8004

(CD)
A

E 3/3

(CD) (CD)

(TA) (TA)
(S/T) (S/T) (TA)
R3019,R3020
XR-A880 : 1.8k
XR-A770 : 3.9k (C) (C)

(B) (B) (B)

(B)
(CD)

(S/T)

(C)
(TA)

XKB3002

(B)
(F/W) BA4558F-HT

(PB)
(B) (B)
B
(CD) (B)

(F/W) (C)
(PB)

(S/T)
(C)

(S/T)

(B)
(C)

(B) (B)
(B)
(T)
(PB)

BA4558F-HT
(F/W)

BA4558F-HT

(F/W) (T) (F/W)

1.8k (T)
150k
1
(PB)

22p

680k

(PB) (PB) (PB)

I CN5501
H CN83

22 E 2/31 2 3 4
 5 6 7 8
XR-A770
A CN6201
E 2/3 AF ASSY
(XWZ3120)

A
4.332MHz

(TA) E 3/3
(S/T)
(TA) (S/T) (S/T)

(C) (C)
(C)

(W)
(B)
(B)
6.8k
(B)

(T)

0.01 (T)
(B)
BA4558F-HT
(B)

(T)
BA4558F-HT
BA4558F-HT

(B) BA4558F-HT
(W)

0.01 B
(B) (B)
6.8k

E 3/3
(B)

(W)

(W)
1SS133
(B)

(W)

(W)
0.033
(W)
1SS133

(W)

BA4558F-HT 1SS133
0.015 0.015

E 3/3
(B)

(B)
(B)
(B)

BA4558F-HT

(B)
BA4558F-HT

0.033

(T)
(F/W) (T) (T) (F/W) E 3/3 C
BA4558F-HT

(F/W) (T) (T) (F/W)

E 3/3
(REC)

(PB)
(PB)

1SS355

E 3/3
(REC)

(C) (TA)
: CENTER SIGNAL ROUTE : TUNER AUDIO SIGNAL ROUTE D
(PB)

(S/T) (PB)
: SURROUND/TWEETER SIGNAL ROUTE : DECK PB SIGNAL ROUTE
(F/W) (REC)
: FRONT/WOOFER SIGNAL ROUTE : DECK REC SIGNAL ROUTE
(PRO)
E 1/3 (B)
: PRO LOGIC SIGNAL ROUTE
(CD)
: AUDIO SIGNAL ROUTE

: PRO LOGIC SIGNAL ROUTE : CD AUDIO SIGNAL ROUTE

5 6 7
E 2/3
8
23
 1 2 3 4
XR-A770
3.6 AF (3/3) and SECONDARY ASSEMBLIES
L J3401
(C)
: CENTER SIGNAL ROUTE
(S/T)
: SURROUND/TWEETER SIGNAL ROUTE
A
(S/T) (F/W)
: FRONT/WOOFER SIGNAL ROUTE
(C) (S/T) (C)
(C) (C)
(S/T) (C)

(S/T) D3674 D3673 (S/T)

(S/T)
(S/T)
U1GC44

(F/W) (F/W)
(S/T)

(F/W)
(F/W)
(C)
E 2/3

470p 470p
100k
(C)

(F/W)

100k
0.47/50

0.47/50

(C)
(F/W) (F/W)
BA4558F-HT 100k
10k 0.15/50
(F/W)
5.6k

B (F/W) 1/2
(F/W) 100k

2/2

5.6k
10k
BA4558F-HT 0.15/50

E 2/3
C

2SC5200(P)

E 2/3 BA4558F-HT
1/2

BA4558F-HT
2/2

D
E 2/3

E 2/3
24 E 3/3
1 2 3 4
 5 6 7 8
XR-A770

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE ONLY WITH SAME TYPE NO. 491.400 MFD, BY REPLACE ONLY WITH SAME TYPE NO. 491002 MFD, BY
LITTELFUSE INK. FOR IC23 (AEK7004). LITTELFUSE INK. FOR IC33 (AEK7013).

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. A

REPLACE ONLY WITH SAME TYPE NO. 4911.25 MFD, BY
LITTELFUSE INK. FOR IC3331 (AEK7010).
E 3/3 AF ASSY (XWZ3120)
(C) (C)

(S/T) (S/T)

JP (S/T) (T)

(S/T) JP

JP
(C) (C)
JP
(F/W)
(F/W) (F/W)
(F/W)

(F/W)

(F/W)
(F/W)
100 FL
B

(F/W)
2SA1037K
100 FL

(F/W)
(F/W) XKN3002
(F/W)

F SECONDARY ASSY(XWZ3121)
C

POWER TRANSFORMER

D
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE ONLY WITH SAME TYPE NO. 491.630 MFD, BY REPLACE ONLY WITH SAME TYPE NO. 491007 MFD, BY
LITTELFUSE INK. FOR IC71 (AEK7006). LITTELFUSE INK. FOR IC21, 22, 31 (AEK7021).

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE ONLY WITH SAME TYPE NO. 491010F MFD, BY REPLACE ONLY WITH SAME TYPE NO. 491005 MFD, BY
LITTELFUSE INK. FOR IC11, 12 (AEK7068). LITTELFUSE INK. FOR IC41 (AEK7019).

5 6 7
E 3/3 F 8
25
 1 2 3 4
XR-A770

3.7 PRIMARY and SUB TRANS ASSEMBLIES

A

E 2/3
J81

B
H SUB TRANS ASSY
(AWZ3139)

POWER TRANSFORMER
C
10000p/250

D
G PRIMARY ASSY
(XWZ3152)

26 G H1 2 3 4
5 6 7 8
XR-A770

AEK1060
(T4A)

AN1
LIVE

NEUTRAL

• NOTE FOR FUSE REPLACEMENT

CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE WITH SAME TYPE AND RATINGS ONLY.

5 6 7
H
8
27
 1 2 3 4
XR-A770

3.8 DISPLAY and CD SW LED ASSEMBLIES

A
DISPLAY ASSY
S5911 : DISPLAY
S5912 : TIMER/CLOCK ADJ
I DISPLAY ASSY
S5913 : ENTER
S5914 : BALANCE
(XWZ3123)
S5915 : ZOOM SURROUND
S5916 : BASS BLASTER
S5917 : EQUALIZER
S5918 : PRESET
S5919 : STANDBY/ON
S5920 : TUNING –
S5921 : TUNING +
S5922 : STOP ( )
S5923 : PLAY/PAUSE
S5924 : REC/STOP
S5925 : FREQ/STATION
S5926 : Dolby NR ON/OFF
S5927 : ASES/COPY
S5928 : AUX
S5929 : TAPE Ι / ΙΙ
S5930 : TUNER/BAND
Function
S5931 : CD
S5951 : VOLUME
S5952 : SOUND MORPHING JOG

D5551,D5552
1SS181

28 I
1 2 3 4
 5 6 7 8
XR-A770

K CN5401

CN5502
E 2/3 CN5102 A
52045–1445

CN5501
52045–3845

1k

CN2901
52045–1945

DECK MECHA
B

D5561–D5568
1SS181

CD SW LED ASSY
S5937 : OPEN/CLOSE ( )
S5938 : DISC CHANGE
S5939 : DISC-3
S5940 : DISC-2
S5941 : DISC-1

D5553,D5554 D5555,D5556 D5557–D5560

1SS181 1SS181 1SS181
D

J CD SW LED ASSY
(XWZ3131)

5 6 7
I J 8
29
 1 2 3 4
XR-A770

3.9 SUB DISPLAY and REAR AMP ASSEMBLIES

I CN5502
K SUB DISPLAY ASSY
A
(XWZ3112)
SUB DISPLAY ASSY
S5401 : 60Hz level control
S5402 : 120Hz level control
S5403 : WOOFER level control
S5404 : P.BASS ON/OFF

D5411,D5412
B

L REAR AMP ASSY (XWZ3122)

(S/T) (S/T) (S/T)

(S/T)

(C) (C)
(C)
(S/T)

(C)
(C)

(S/T)
(S/T)

(C)

(C)
(S/T)

(S/T) (S/T)
D
(C)

(C)
: CENTER SIGNAL ROUTE
(S/T)
: SURROUND/TWEETER SIGNAL ROUTE

E 3/3 CN3401
30 K L 1 2 3 4
 1 2 3 4
XR-A770

4. PCB CONNECTION DIAGRAM

A

NOTE FOR PCB DIAGRAMS :

1. Part numbers in PCB diagrams match those in the schematic 3. The parts mounted on this PCB include all necessary parts for
diagrams. several destinations.
2. A comparison between the main parts of PCB and schematic For further information for respective destinations, be sure to
diagrams is shown below. check with the schematic diagram.
Symbol In PCB Symbol In Schematic 4. View point of PCB diagrams.
Part Name
Diagrams Diagrams
B C E B C E
Connector Capacitor
Transistor
B C E

B C E B C E SIDE A
Transistor
B C E with resistor

D G S D G S
Field effect
D G S transistor
P.C.Board Chip Part SIDE B
B
Resistor array

3-terminal
regulator

4.1 REAR AMP ASSY

REAR AMP E
CN3401
L
ASSY SIDE A

(XNP3009-B)

L REAR AMP ASSY SIDE B

(XNP3009-B)

1 2 3
L
4
31
 1 2 3 4
XR-A770

4.2 CD, MOTOR and SW ASSEMBLIES

A
D SW ASSY

C MOTOR LOADING

ASSY MOTOR

B M
SERVO
MECHANISM
ASSY
Q8101

PICKUP
ASSY

Q8254

Q8252

Q8251

Q8253
D E
CN1052

SIDE A (ANP7144-E)
B CD ASSY
32 B C D
1 2 3 4
1 2 3 4
XR-A770

D SW ASSY A

C MOTOR ASSY

IC8201

IC8101

IC8301

(ANP7144-E) SIDE B
B CD ASSY

1 2 3
B C D 4
33
 1 2 3 4
XR-A770
4.3 AF ASSY

E AF ASSY
A

FAN MOTOR
H
CN83

J11

F
J11

VR280

34 E
1 2
Q3081 Q3081

3
IC23
Q21 Q22
IC32
Q34 Q31
Q54

4
IC42
Q51 Q52 Q57
IC51 IC
 5 6 7 8
XR-A770

B CN8004
A

I CN5501

A CN6201

L J3401

MECHANISM UNIT

SIDE A
(XNP3009-B)
VR2802 VR2801 VR2301-VR2306

Q51 Q52 Q57

IC51 IC3331
5
Q2801
IC3301
IC2301
Q2804
Q2802
6 7
E
8
35
 1 2 3 4
XR-A770

E AF ASSY
A

SIDE B
IC5892 IC5891 Q2306 Q2105 Q2104 IC2201 Q5751 Q5752 IC3

36 E
1 2
Q2802 Q2805-Q2807
Q3607

3
Q3622
IC2101 Q2103
Q2301 Q3353 Q3354
IC5751 IC5751 IC3
Q2203
Q3611 Q3606 Q3605 Q3311-Q3314
4
Q2204
 5 6 7 8
XR-A770

(XNP3009-B)

5751 Q5752 IC3101-IC3103 Q3101 Q3102 IC3001

5751 IC5751 IC3381
Q2203
3311-Q3314
Q2204 Q56 Q53 Q55

5
Q3401-Q3403
IC34 Q33
IC3201-IC3203

6
Q3202 Q3201

7
E
8
37
 1 2 3 4
XR-A770

4.4 SECONDARY ASSY

A
F SECONDARY ASSY
IC41

Q71 IC71

POWER TRANSFORMER
T1
IC21
B

IC22
IC31

SIDE A
E J11

F SECONDARY ASSY

(XNP3009-B)

38 F
1 2
SIDE B
3 4
 1 2 3 4
XR-A770

4.5 PRIMARY and SUB TRANS ASSEMBLIES

A

T1
POWER TRANSFORMER

G PRIMARY
ASSY

AC IN
H SUB TRANS ASSY
NEUTRAL
LIVE

D
E J81

(XNP3013-B)

SIDE A

1 2 3
G H
4
39
 1 2 3 4
XR-A770

4.6 DISPLAY and CD SW LED ASSEMBLIES

E I DISPLAY
A CN5102 ASSY

MECHANISM
UNIT

J CD SW
LED
ASSY

(XNP3013-B)

SIDE A
K
CN5401

40 I J
1 2 3 4
 1 2 3 4
XR-A770

I DISPLAY
ASSY A

Q2901
Q2903

Q2906
Q2908

Q5605 IC5601

Q2904

IC5501
Q2910

C
Q5502
Q5501
Q5821 IC5631

J CD SW
LED
Q5601 ASSY
Q5606
Q5604

IC3901

D
SIDE B
(XNP3013-B)
IC3931

1 2 3
I J 4
41
 1 2 3 4
XR-A770
4.7 SUB DISPLAY ASSY
K SUB DISPLAY ASSY
A

IC5411

B Q5411
Q5415

SIDE A SIDE B

D I
CN5502

(XNP3013-B)

42 K
1 2 3 4
 1 2 3 4
XR-A770

4.8 FM/AM TUNER MODULE

A

E CN3051
A FM/AM TUNER MODULE

VR6201
Q6204 Q6203

SIDE A

A FM/AM TUNER MODULE

IC6201 Q6201 Q6202 Q6601 Q6214 Q6501

IC6202 Q6205 Q6102 - Q6105 Q6101

(ANP7160-B) D

SIDE B

1 2 3
A
4
43
XR-A770

Mark No. Description Part No. Mark No. Description Part No.

5. PCB PARTS LIST

NOTES: • Parts marked by "NSP" and can not be supplied.
• The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
560 Ω → 56 × 101 → 561 ........................................................ RD1/4PU 5 6 1 J
47k Ω → 47 × 103 → 473 ........................................................ RD1/4PU 4 7 3 J
0.5 Ω → R50 ..................................................................................... RN2H R 5 0 K
1Ω → 1R0 ..................................................................................... RS1P 1 R 0 K
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62k Ω → 562 × 101 → 5621 ...................................................... RN1/4PC 5 6 2 1 F

Mark No. Description Part No. Mark No. Description Part No.
LIST OF PCB ASSEMBLIES F6202 ATF7011
L6107 ATH1043
FM/AM TUNER MODULE AXQ7068 L6603 LAU220J
L6206, L6208, L6605 LAU2R2J
NSP $M SERVO BOARD ASSY XWX3005
CD ASSY XWZ3141
MOTOR ASSY AWZ8428 TRANSFORMERS
NSP SW ASSY AWZ8429 T6201 ATB7008
T6101 ATE7002
MAIN ASSY XWM3064
REAR AMP ASSY XWZ3122
AF ASSY XWZ3120
CAPACITORS
SECONDARY ASSY XWZ3121 C6113, C6212, C6274, C6275, C6611 CCSQCH101J50
C6116, C6208, C6221 CCSQCH150J50
NSP COMPLEX ASSY XWM3065 C6222 CCSQCH180J50
PRIMARY ASSY XWZ3152 C6271 CCSQCH200J50
SUB TRANS ASSY XWZ3139 C6117 CCSQCH330J50
DISPLAY ASSY XWZ3123
CD SW LED ASSY XWZ3131 C6608 CCSQCH680J50
SUB DISPLAY ASSY XWZ3112 C6118 CCSQCH8R0D50
C6111, C6122 CCSQCK1R0C50
C6112, C6127 CCSQCK2R0C50
A FM/AM TUNER MODULE
C6105 CCSQSL471J50

C6101 CCSQTH110J50
SEMICONDUCTORS C6119 CCSQTH150J50
IC6201 LA1832ML C6109 CCSQTH270J50
IC6202 LC72131MD C6107, C6110 CCSQTH300J50
Q6102 2SC2223 C6106 CCSQTH330J50
Q6203 2SC2705
Q6201, Q6202 2SC2712 C6234, C6235 CEAL1R0M50
C6245 CEAL470M16
Q6103, Q6214, Q6601 2SC2714 C6224 CEAS100M50
Q6104, Q6105 2SK302 C6243 CEAS101M16
Q6101 3SK194 C6231 CEAS1R0M50
Q6204 DTA124ES
Q6205 DTC124EK C6227 CEAS220M16
C6236 CEAS2R2M50
D6202 1SS254 C6216 CEAS330M16
D6101–D6104 1SV228 C6262 CEAS3R3M50
C6219 CEAS470M10
COILS AND FILTERS
L6106 ATC1003 C6244 CEAS470M16
L6105 ATC1015 C6249, C6250, C6265, C6266 CEAS4R7M50
L6101 ATC1016 C6258 CEJA470M16
L6102 ATC1017 C6215 CFTLA103J50
L6103 ATC1018 C6214 CFTLA224J50

L6104 ATC1019 C6115, C6125, C6126, C6211, C6254 CKSQYB102K50

F6203 ATF-119 C6601 CKSQYB102K50
F6206 ATF7008 C6102, C6114, C6121, C6123, C6124 CKSQYB103K50
F6601 ATF7009 C6210, C6213, C6237, C6267, C6276 CKSQYB103K50
F6204 ATF7010 C6279, C6281, C6604 CKSQYB103K50

44
 XR-A770

Mark No. Description Part No. Mark No. Description Part No.
C6251, C6252 CKSQYB123K50 C8137, C8138, C8201, C8309, C8312 CKSQYB103K50
C6606, C6607 CKSQYB182K50 C8134, C8302, C8303 CKSQYB104K25
C6203, C6259 CKSQYB223K50 C8353, C8359 CKSQYB152K50
C6228 CKSQYB472K50 C8111 CKSQYB153K25
C6209 CKSQYB473K50 C8114, C8117, C8120, C8121 CKSQYB154K16

C6230 CKSQYB821K50 C8125 CKSQYB221K50

C6218, C6223, C6255 CKSQYF103Z50 C8107 CKSQYB223K50
C6220, C6226, C6242, C6256 CKSQYF223Z50 C8110 CKSQYB331K50
C6225 CKSQYF473Z50 C8115, C8128 CKSQYB332K50
C6610 CKSYB103K50 C8113 CKSQYB333K25

C8112, C8141 CKSQYB334K16

RESISTORS C8116, C8140, C8355, C8357 CKSQYB473K50
R6602 RD1/4PU221J C8118, C8255–C8257, C8301 CKSQYF104Z25
R6115, R6119, R6123, R6127, R6129 RS1/8S0R0J C8304, C8305 CKSQYF104Z25
R6906, R6909, R6911 RS1/8S0R0J
R6112 RS1/8S473J
VR6201 (10kΩ) RCP1045 RESISTORS
All Resistors RS1/10S J
Other Resistors RS1/10S J
OTHERS
OTHERS CN8003 6P JUMPER CONNECTOR 52151-0610
BN6202 ANTENNA TERMINAL AKA7001 CN8002 KR CONNECTOR B6B-PH-K-S
X6202 CERAMIC RESONATOR ASS1066 CN8005 3P SIDE POST BS3P-SHF-1AA
(456kHz) CN8004 FFC CONNECTOR 22P HLEM22R-1
X6201 CRYSTAL RESONATOR ASS1093 CN8001 FFC CONNECTOR SLW15S-1C7
(7.2000MHz)
X8301 CERAMIC RESONATOR PSS1008
CN6201 14P SOCKET KP200IA14L (16.9344MHz)
AM RF TUNING BLOCK AXX7042

C MOTOR ASSY
B CD ASSY
SWITCHES AND RELAYS
SEMICONDUCTORS S8503 ASG7009
IC8201 BA5923FP
IC8101 LA9241ML
IC8301 LC78622NE
OTHERS
Q8101 2SA1048 J8502 JUMPER WIRE 4P D20PWW0405E
Q8251, Q8252 2SB1237X MOTOR PULLEY PNW1634
CARRIAGE MOTOR VXM1033
Q8253, Q8254 2SD1858X
D8253 1SS181
D8251, D8252 1SS355
D SW ASSY
COILS AND FILTERS SWITCHES AND RELAYS
L8351, L8352 LFA1R0K S8502 ASG7009
L8201, L8371 LFA470J S8501 DSG1017
OTHERS
CAPACITORS J8501 JUMPER WIRE 6P D20PWY0610E
C8145, C8352, C8354, C8356, C8358 CCSQCH101J50
C8361, C8362 CCSQCH101J50
C8132, C8311
C8310
CCSQCH150J50
CCSQCH180J50
E AF ASSY
C8131 CCSQCH300J50 SEMICONDUCTORS
IC23 (400mA) AEK7004
C8129 CCSQCK1R0C50 IC3331 (1.25A) AEK7010
C8142 CEAL101M6R3 IC33 (2A) AEK7013
C8127 CEAL1R0M50 IC2101, IC3101–IC3103, IC3201 BA4558F-HT
C8126, C8139 CEAL470M16 IC3202, IC3381, IC34, IC5691 BA4558F-HT
C8135 CEAL4R7M16
IC5751 BU1923F
C8124 CEALR47M50 IC3203 BU4066BCF
C8136 CEAT100M50 IC5891, IC5892 BU4094BCF
C8108, C8306, C8371 CEAT101M10 IC2201 HA12136AF
C8202 CEAT101M25 IC2301 HA12211NT
C8101 CEAT3R3M50
IC3001 LC75396NE
C8105 CEAT470M16 IC42 NJM7805FA
C8109 CEATR22M50 IC32 NJM7812FA
C8106, C8119, C8133, C8307, C8308 CKSQYB102K50 IC3301 STK407-090B
C8360 CKSQYB102K50 Q3354, Q3601, Q3621, Q55, Q5751 2SA1037K
C8102, C8122, C8123, C8130 CKSQYB103K50
45
XR-A770

Mark No. Description Part No. Mark No. Description Part No.
Q2806 2SB1197K C3313, C3314 CEANPR47M50
Q22 2SB1375 C2207, C2803, C2810, C3041, C3042 CEAT100M50
Q2803, Q2804 2SC1815 C3047, C3048, C3081, C3091–C3093 CEAT100M50
Q2801 2SC2240 C3441–C3444, C3450, C36, C3602 CEAT100M50
Q2102, Q2201, Q2202, Q3101, Q3102 2SC2412K C51, C5758 CEAT100M50

Q33, Q3353, Q3401, Q3603 2SC2412K C2002, C2316 CEAT101M16

Q3605–Q3608, Q56 2SC2412K C3651 CEAT101M35
Q21 2SC5200(P) C3303, C3304, C3622, C54 CEAT101M50
Q3081 2SD1858X C2312, C2313, C3035, C3036 CEAT1R0M50
Q34, Q54 2SD1858X C3107, C3108 CEAT1R0M50

Q31 2SD2012 C1990, C2106, C2214, C2215 CEAT220M50

Q2203, Q2204, Q2805, Q3311, Q3312 2SD2114K C2321, C2322 CEAT220M50
Q2301, Q2302 2SK368 C2001 CEAT221M16
Q3201, Q3313, Q3403 DTA124EK C40 CEAT222M25
Q2104, Q2105, Q3202, Q3314, Q3402 DTC124EK C2201, C2202, C2205, C2206 CEAT2R2M50

Q3641, Q5752 DTC124EK C2212, C2213, C2319, C2320 CEAT2R2M50

Q2103, Q2306, Q2802, Q2807 DTC143EK C3005–C3012, C3015–C3018 CEAT2R2M50
D3301, D3302 1SR139-100 C3039, C3040, C3043–C3046, C3104 CEAT2R2M50
D2301–D2306, D3101, D3102, D32 1SS133 C3205, C3206, C3211, C3212 CEAT2R2M50
D3202, D3351–D3354, D3361, D3362 1SS133 C2804, C2805, C3105, C5754 CEAT330M16

D34, D3403, D3603, D3621, D3622 1SS133 C3406 CEAT330M25

D3625–D3627, D51 1SS133 C11, C12 CEAT332M35
D3402 1SS184 C3106, C3109 CEAT4R7M50
D2102, D2103, D2191, D2201, D2202 1SS355 C3021, C3022 CEATR10M50
D3051, D3201, D3601, D3604 1SS355 C2203, C2204, C3101, C3102 CEATR22M50

D3623, D3624, D5891 1SS355 C3325 CEATR47M50

D3355, D3356 20E2-FC C35, C43 CEHAQ100M50
D31 GBU4D C32, C42 CEHAQ1R0M50
D3357, D3358 MTZJ10C C3601 CEHAQ221M16
D3083 MTZJ11C C3027, C3028 CFTLA334J50

D33 MTZJ20A C3023, C3024 CFTLA474J50

D52 MTZJ22D C3311, C3312 CFTYA154J50
D3363, D3364 MTZJ39C C2812 CKCYB103K50
D3401 MTZJ4.7B C2802 CKCYB681K2H
D2001 MTZJ6.2A C1996, C3308, C3993, C3994, C5693 CKSQYB102K50

D48 MTZJ6.8C C5892 CKSQYB102K50

C1653, C1922, C1993–C1995 CKSQYB103K50
C1998, C1999, C2003, C2004, C2315 CKSQYB103K50
COILS AND FILTERS C2317, C2318, C3053, C3103 CKSQYB103K50
L3331, L3332 ATH-133 C3201, C3202, C5001, C5753 CKSQYB103K50
L2801 ATX7002
L5751 LAU1R0J C1651, C1652, C1997, C2191, C2193 CKSQYB104K25
L1651, L3991 LAU4R7J C3097, C3099, C3652 CKSQYB104K25
L2301, L2302 LTA822J C3033, C3034 CKSQYB122K50
C2208, C2209 CKSQYB152K50
F2201, F2202 RTF1209 C3209, C3210 CKSQYB153K50

SWITCHES AND RELAYS C2323, C2326 CKSQYB223K25

RY3601 ASR7008 C3029, C3030 CKSQYB273K25
C2808, C2809 CKSQYB332K50
C3207, C3208 CKSQYB333K50
CAPACITORS C2333, C2334 CKSQYB392K50
C3345, C3346, C3435, C3436(10000pF) ACG7021
C2303, C2304 (270pF) ACG7024 C3315, C3316 CKSQYB471K50
C2301, C2302 CCSQCH100D50 C2807, C3051, C3052 CKSQYB472K50
C3203, C3204 CCSQCH121J50 C3111, C3112, C5891 CKSQYB473K25
C2192 CCSQCH220J50 C2307, C2308, C2331, C2332 CKSQYB681K50
C3013, C3014 CKSQYB681K50
C3003, C3004 CCSQCH221J50
C5751, C5752, C5755 CCSQCH270J50 C3019, C3020, C3031, C3032 CKSQYB682K50
C5757 CCSQCH271J50 C3323, C3324 CKSQYB682K50
C38 CCSQCH331J50 C3025, C3026 CKSQYB683K25
C3319, C3320 CCSQCH3R0C50 C3331–C3333, C3335–C3340 CKSQYF104Z50
C3451–C3458 CKSQYF104Z50
C3321, C3322 CCSQCH470J50
C5756 CCSQCH561J50
C33 CEAL100M50
C3621 CEAL2R2M50
C3317, C3318 CEANP100M35

46
 XR-A770

Mark No. Description Part No. Mark No. Description Part No.
C2194, C37 CKSQYF105Z16
C2801 CQHA822J2A
CAPACITORS
C2210, C2211 CQMBA103J50 C72 CEAT220M50
C2806 CQMBA223J50 C71 CEAT221M63
C31 (4700µF/42V) XCH3003 C41 CEAT222M25
C13 CQMA103K2E
C21, C22 (4700µF/80V) XCH3001
RESISTORS
R2809 RD1/2LMF4R7J
R2812 RD1/2PM270J
RESISTORS
R2813 RD1/2PM471J R72 RD1/4PU222J
R3333, R3334 RD1/4LMF101J Other Resistors RS1/10S J
R3317, R3318 RD1/4PU104J
OTHERS
R3116 RD1/4PU105J J11 JUMPER WIRE 17P D20PYY1740E
R3081 RD1/4PU221J
R33 RD1/4PU222J
R3009 RD1/4PU472J
R2334 RD1/4PU562J G PRIMARY ASSY
R41 RN1/10SE1002D CAPACITORS
R40 RN1/10SE2002D C3 (10000pF/AC250V) ACG7020
R39 RS1/10S3300F
R3991, R3992 RS2LMF331J
R30 RS3LMF470J
H SUB TRANS ASSY
R3601, R3602 RS3LMFR22J
VR2303-VR2306 (10kΩ) VCP1156
SEMICONDUCTORS
VR2301,VR2302 (100kΩ) VCP1162 IC81 NJM7805FA
VR2801,VR2802 (220kΩ) VCP1164 Q81 2SD1859X
Other Resistors RS1/10S J D85, D88–D90 1SS133
D81–D84 S5688G

OTHERS
4P CABLE HOLDER 51048-0400
COILS AND FILTERS
CN1052 22P FFC CONNECTOR 52045-2245 L1 ATF1136
CN5102 38P FFC CONNECTOR 52045-3845
CN3401 17P JUMPER CONNECTOR 52147-1710 TRANSFORMERS
CN3432,CN3433 2P CONNECTOR 5569-02A1 T2 ATT7027
CN3331 4P SPEAKER TERMINAL AKE7001
CN2302 KR CONNECTOR B2B-PH-K-S SWITCHES AND RELAYS
CN2303 KR CONNECTOR B3B-PH-K-R RY81 ASR7018
CN2301 KR CONNECTOR B3B-PH-K-S
J81 JUMPER WIRE 4P D20PYY0440E
CAPACITORS
JA1651 OPTICAL LINK OUT GP1F32T C1, C2 (10000pF/AC250V) ACG7020
CN3051 14P PLUG KM200IB14 C83 CEAT100M50
PCB BINDER VEF1040 C82 CEAT102M25
J3051 CONNECTOR ASSY 2P XDX3002
JA3001,JA3441 2P PIN JACK XKB3002 RESISTORS
R83 RS1/10S102J
CN3991 HEADPHONE JACK XKN3002 Other Resistors RD1/4PU J
X5751 CRYSTAL RESONATOR ASS7004
(4.332MHz)
OTHERS
CN83 4P JUMPER CONNECTOR 52147-0410
F SECONDARY ASSY H1, H2
AN1
FUSE CLIP
1P AC INLET
AKR7001
BKP1046
SEMICONDUCTORS
IC71 (630mA) AEK7006
IC41 (5A)
IC21, IC22, IC31 (7A)
AEK7019
AEK7021
I DISPLAY ASSY
IC11, IC12 (10A) AEK7068 SEMICONDUCTORS
Q71 2SA965 IC5631 BA3835F
IC5601 BU2092F
D73 1SS133 IC5501 PDC049A
D21 GBU4DL-5303 Q5501 2SA1037K
D11 GBU6DL-5302 Q2903, Q2906, Q2908 2SB1132
D74 MTZJ36A
D75 MTZJ8.2B Q5604, Q5801 2SC2412K
Q2910, Q2911 DTA124EK
D41–D44, D71, D72 S5688G Q5606 DTC124EK
Q2901, Q2904, Q2907, Q5502, Q5603 DTC143EK
Q5821 DTC143EK

47
XR-A770

Mark No. Description Part No. Mark No. Description Part No.
D5592, D5594–D5596, D5811 1SS133
D5551–D5568
D2901–D2903, D5569, D5570, D5626
1SS181
1SS355 J CD SW LED ASSY
D5901 1SS355
D5612 MAA5064X
SEMICONDUCTORS
D5623 SLP3118C51H
D5608–D5611 MBG5064X D5624 SLP7118C51H
D5613–D5616 MPG5064X D5622 SLP9118C51H
D5617–D5620 SLP3118C51H
D5603–D5607, D5621 SLP9118C51H SWITCHES AND RELAYS
S5937–S5941 XSG3001
COILS AND FILTERS
L5811 LAU220J RESISTORS
All Resistors RS1/10S J
SWITCHES AND RELAYS
S5951 ASX7004 OTHERS
S5952 ASX7017 J5501 JUMPER WIRE D20PWW0615E
S5911–S5931 XSG3001

CAPACITORS
C5812 (0.047F/5.5V) ACH1246
K SUB DISPLAY ASSY
C5601 CCSQSL151J50 SEMICONDUCTORS
C5821 CEJA100M16 Q5411 DTC143EK
C5803 CEJA1R0M50 D5411, D5412 SLP7118C51H
C5510, C5811, C5814 CEJA470M16

C5804 CKSQYB102K50 SWITCHES AND RELAYS

C5995, C5996 CKSQYB103K50 S5403 ASX7004
C5816, C5997–C5999 CKSQYB104K25 S5404 XSG3001
C5505, C5509, C5951–C5954 CKSQYB471K50 S5401, S5402 XSX3002
C5506–C5508, C5511 CKSQYB472K50

C5602, C5631–C5634, C5901 CKSQYF104Z50

RESISTORS
C5503, C5504, C5813, C5822 CKSQYF473Z50 R5430 RD1/4PU561J
Other Resistors RS1/10S J

RESISTORS
R5529 (470Ω) ACN7056
OTHERS
R5554, R5556, R5561, R5562 (1.5kΩ) ACN7062 CN5401 14P FFC CONNECTOR 52045-1445
R5558, R5563, R5564 (47kΩ) ACN7077
R5508 RA11T104J
R5506 RA7T104J
L REAR AMP ASSY
R2907, R2909, R2910, R5919 RD1/4PU102J SEMICONDUCTORS
R5915 RD1/4PU181J IC3401 TDA8560Q
R5925 RD1/4PU331J Q3661, Q3671, Q3672 2SA1037K
R5605, R5606, R5612, R5613, R5926 RD1/4PU561J Q3352 IRF540A
R2902, R5604, R5607–R5611 RD1/4PU681J Q3351 IRF9540A
D3662 1SS133
R5927 RD1/4PU821J
R2911–R2913 RS1/8S0R0J D3663 1SS355
R5614 RS1/8S331J D3359, D3360 MTZJ18B
R2905 RS1/8S681J D3661 MTZJ2.7A
Other Resistors RS1/10S J D3671 MTZJ20A
D3371, D3372 U1GC44
OTHERS
CN5502 14P FFC CONNECTOR 52045-1445 TH3661 AEX7002
CN2901 19P FFC CONNECTOR 52045-1945
CN5501 38P FFC CONNECTOR 52045-3845 CAPACITORS
5901 REMOTE RECEIVER UNIT GP1U28X C3671 CEAT101M10
V5621 FL TUBE XAV3004 C3411 CEAT101M35
C3401, C3402 CEATR47M50
2902 FL HOLDER XNG3008 C3403, C3404, C3413–C3416 CKSQYB102K50
X5501 CERAMIC RESONATOR RSS1050
(6MHz)
RESISTORS
R3353, R3354 RD1/4PU101J
Other Resistors RS1/10S J

OTHERS
J3401 JUMPER WIRE 17P D20PYY1720E

48
 XR-A770

6. ADJUSTMENT
6.1 TUNER SECTION
FM Tuner Section
• Set the mode selector to FM BAND.
• Connect the wiring as shown in Fig. 1.
FM SG (1kHz, ± 75kHz dev.) Reception
Step Adjustment Adjustment
Frequency Level Frequency Specifications
No. Title Location
(MHz) (dBµV) Display
L6104
Adjust so that the DC voltage between the
Front End L6105
1 106 0-30 106MHz IC6201-pin 20 and GND becomes at maximum
Sensitivity L6102
level.
T6101
98 Minimize the distortion with 1/8 rotation of the
2 Stereo Distortion 80 98MHz T6101
(ON STEREO) core.
TUNED IND. Adjust so that the indicator of TUNED IND.
3 98 18 ± 2 98MHz VR6201
Lighting Level starts to light up.
Note:
Before adjusting, make sure there is no gap between L6101 and L6102 as well as between L6103 and L6104. If there is a gap between
them, bring them into contact with each other first, and then make adjustments.

AM Tuner Section
• Set the mode selector to AM BAND.
• Connect the wiring as shown in Fig. 1.
AM SG (400Hz, 30% Mod.) Reception
Step Adjustment Adjustment
Frequency Level Frequency Specifications
No. Title Location
(kHz) (dBµV/m) Display
Adjust so that the DC voltage between the
Front End
1 999 ∗1 35-45 999kHz ∗1 T6201 IC6201-pin 20 and GND becomes at maximum
Sensitivity
level.
∗1: For the area using 10kHz step, frequencies should be 1000kHz.

60cm
Loop antenna

AM SG AM antenna terminal
Center Center

DC
MPX SG FM SG PRODUCT Voltmeter

FM75Ω antenna terminal

Fig. 1 AM and FM Adjustment Wiring Diagram

FM/AM TUNER MODULE (AXQ7068)

AM T6201
antenna AXX7042
terminal
YELLOW BLACK

FM L6101 L6105
antenna VR6201
terminal T6101
L6102
L6103 L6104

Fig. 2 Adjustment Point

49
XR-A770

6.2 CASSETTE DECK SECTION

• Adjustment points and test points are shown in Fig.3, Fig.5 and Fig.7.
Mechanical Adjustment
• Test tape: NCT-111 (3kHz, 30min).
1. Tape Speed Adjustment
Adjusting Measurement
No. Mode Test Tape Adjustment Procedure Remarks
Points Points
Press the PLAY SW and adjust so that the reading
ADJ. VR on TAPE TEST
Deck I NCT-111 becomes 3000Hz ± 20Hz. Confirm that wow & flutter
1 CASSETTE POINT (Rch)
PLAY (Playback : 3kHz) level is below 0.3% (in the reverse direction, confirm
MECHA(Fig. 3) (AF Assy)
that the reading is within 3000Hz ± 60Hz).

Tape Speed
ADJ. VR
AF Assy
Front Side Cassette
Mechanism
Section
(Side View)

Fig.3 Tape Speed ADJ. Point

Electrical Adjustment
Check the following before starting. Playback Adjustment (Decks I and II)
(1) Confirm that the tape speed adjustment has been completed. (1) Head Azimuth Adjustment
(2) Clean the heads and demagnetize them using a head eraser. (2) Playback Level Adjustment
(3) Set the measurement level to 0 dBV = 1 Vrms.
(4) Use the specified tape for adjustment. Use the labeled (A) Recording Adjustment (Deck I)
side of the test tape. (1) Bias Oscillation Frequency Adjustment
STD-331E : For playback check (2) Recording Bias Adjustment
STD-632 : Normal blank tape (3) Recording Level Adjustment.
(5) Provide yourself with the following measuring devides:
• AC millivoltmeter
(4) ALC Operation Check

• Low-frequency oscillator
• Attenuator
• Oscilloscope
(6) Adjust both right and left channels unless otherwise specified. * As the reference recording level is 250nwb/m for STD-331E, the
(7) Turn the DOLBY NR switch off unless otherwize specified. recording level will be higher by 4 dB for STD-331B (160nwb/m).
(8) Warm up the unit for several minutes before adjustment. When adjusting, pay carefull attention to the type of tape used.
In particular, be sure to warm up the unit in the REC/PLAY
mode for 3 to 5 minutes before starting recording/playback
frequency characteristics adjustment. Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation.
(9) Always follow the indicated adjustment order.
“DOLBY” and the double-D symbol are trademarks of Dolby
Otherwise, a complete adjustment may not be achieved.
Laboratories Licensing Corporation.

50
 XR-A770

0 dB 30s
0 dB: 315 Hz, 250 nwb/m
30s 30s 30s 10s 10s ......................................................................................................... 10s
315Hz –20 dB
12.5 6.3 500 250 125
6.3kHz 10kHz 315Hz 14kHz kHz 10kHz 8kHz kHz 4kHz 2kHz 1kHz Hz Hz Hz 63Hz 40Hz

Fig. 4 STD-331E Test Tape

Playback Adjustment
(1) Head Azimuth Adjustment
• Do not switch between forward and reverse operation with the screwdriver inserted.
Input Signal/ Measurement Adjustment
Step Mode Adjusting Points Remarks
Test Tape Points Value
STD-331E test tape Deck I Head azimuth TAPE TEST
Max. playback After adjustment, apply silicon bond to
1 PLAY (Playback: 10kHz, adjustment POINT (L, Rch)
Deck II signal level the head azimuth adjustment screw.
-20dB) screw (Fig. 5) (AF Assy)

(2) Playback Level Adjustment

• Since this adjustment determines playback Dolby NR level, perform it carefully.
Input Signal/ Measurement Adjustment
Step Mode Adjusting Points Remarks
Test Tape Points Value
VR2303(Lch)
STD-331E Deck I
VR2304(Rch) TAPE TEST
1 PLAY test tape POINT (L, Rch) – 3.7dBV
(Playback: 315Hz,0dB) VR2305(Lch) (AF Assy)
Deck II
VR2306(Rch)

PLAY BACK

12.5k
250 10k

3dB 3dB 4dB

RECORDING

12.5k
250 10k

3dB 3dB 5dB

REV Azimuth Adjustment Screw FWD Azimuth Adjustment Screw

Fig. 5 Head Azimuth Adjustment Screw Fig. 6 Frequency Characteristics

51
XR-A770

Recording Adjustment
(1) Bias Oscillation Frequency Adjustment
Input Signal/ Measurement Adjustment
Step Mode Adjusting Points Remarks
Test Tape Points Value
Deck II 



 



 Oscillation If the REC/STOP button for four
Load the STD-632
Between A frequency to seconds while the power is in STAND
1 REC test tape and set the L2801
DECK I point in Fig.7 be 105.0kHz BY mode, the frequency will decrease
recording mode. (AF Assy)
and GND. ± 2kHz. 2 to 3 kHz.

(2) Recording Bias Adjustment

• Since this adjustment affects recording bias, prevent distortion from increasing due to underbias.
Measurement
Step Mode Input Signal/Test Tape Adjusting Points Adjustment Value Remarks
Points

Input a 315Hz signal to the Deck II 





 TAPE TEST
1 REC AUX terminal and set the input POINT (L, Rch) – 23.7dBV
selector to AUX. DECK I Input signal level (AF Assy)

Load the STD-632 test tape and Deck II 





 TAPE TEST Repeat adjustment until playback level
REC → record/playback the 315Hz and
2 POINT (L, Rch) of the 10kHz signal is within 0 ± 0.5dB
PLAY 10kHz signals. VR2801(Lch)
DECK I (AF Assy) from that of the 315Hz signal.
(see the Note below) VR2802(Rch)
Note : Set the 10kHz input signal level to the same value as the 315Hz input signal level of step 1.

(3) Recording Level Adjustment

Measurement
Step Mode Input Signal/Test Tape Adjusting Points Adjustment Value Remarks
Points

Input a 315Hz signal to the Deck II TAPE TEST

1 REC AUX terminal and set the input Input signal level POINT (L, Rch) – 7.7dBV
selector to AUX. DECK I (AF Assy)

Load the STD-632 test tape and Deck II 





 TAPE TEST Repeat recording, playback and
REC →
2 record/playback the 315Hz POINT (L, Rch) adjustment until playback level of the
PLAY VR2301(Lch)
signal. DECK I (AF Assy) 315Hz signal becomes – 7.7dBV.
VR2302(Rch)

(4) ALC Operation Check

Measurement
Step Mode Input Signal/Test Tape Adjusting Points Adjustment Value Remarks
Points
1 Input signal level TAPE TEST – 8.2dBV
Input a 315Hz signal to the
REC/ POINT
AUX terminal and set the input Set to a level +10dB adove the Confirm that the reading is
2 PAUSE (L, Rch)
selector to AUX. input level at step1. – 2.2 ± 2.5dBV.
(AF Assy)

52
 XR-A770

AF ASSY SIDE A

FRONT

TAPE TEST
POINT
R ch VR2303 VR2305
L ch
VR2301
VR2302 VR2306
VR2304

A VR2802 VR2801

L2801

Fig.7 Adjustment and Measurement Points

53
XR-A770

6.3 TEST MODE

NOTE: There is no information to be shown in this CD adjustment.

How to Start/Cancel Test Mode

TEST MODE : ON
TEST DISC: YEDS-7
CD TEST
CD

Short Point
STANDBY/ON Function CD

CD TEST

"TEST 4"

Short Point

TEST MODE : PLAY

TEST DISC: YEDS-7 PLAY/
REC/ PLAY/ PAUSE
STOP PAUSE

CLOSE OPEN
inwards outwards Spindle motor: START
Laser diode: LIGHTS UP Tracking servo:
Pickup Move Focus servo: CLOSE Spindle servo: CLOSE

TEST MODE : STOP CANCEL

REC/
STOP

STOP all operations. STANDBY/ON

Test Point
SIDE B
DISPLAY ASSY

Bottom Side

CD TEST

54
 XR-A770

7. GENERAL INFORMATION
7.1 PARTS
7.1.1 IC
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.

HA12136AF (AF ASSY : IC2201)

• Dolby B Type NR System IC

•Pin Function
No. Pin Name Function No. Pin Name Function
1 REC IN Recording (Encode) input 9 REC OUT Recording (Encode) output
2 VCC Power supply 10 DET Time constant pin for the level detector
3 PB IN Playback (Decode) input 11 PB OUT Playback (Decode) output
Mode control pin for REC/PB (Encode/Decode)
4 Vref Reference voltage 12 REC/PB
"H" : REC (Encode), "L" : PB (Decode)
Mode control pin for NR ON/OFF
5 NR ON/OFF 13 BIAS Reference current input pin for the active filters
"H" : NR ON, "L" : NR OFF
6 PB OUT Playback (Decode) output 14 PB IN Playback (Decode) input
7 DET Time constant pin for the level detector 15 GND Ground
8 REC OUT Recording (Encode) output 16 REC IN Recording (Encode) input

HA12211NT (AF ASSY : IC2301)

• REC Equalizer and PB Equalizer System IC
•Block Diagram
REC IN
from logic to Dolby

PB–OUT(L)

PB–OUT(R)
REC–SEL
TAPE(R)
TAPE(L)

AUX(R)
AUX(L)
GND

B(R)
IREF

HSP

B(L)
BCr

ACr

A/B

30 29 28 27 26 25 24 23 22 21 20 19 18 17 16

PB–CAL

PB–CAL
L–ch

12dB
R–ch
L–ch

B
R–ch
REC–EQ

A A

139k B 10k

5k 2.7k 2.26k 1.12k

PB–CAL

PB–CAL
PB–EQ

PB–EQ
PB–NF

PB–NF
PB–IN

PB–IN

PB–IN

PB–IN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
VREF

(R)

(R)
B(R)
REC–RETURN
REC–OUT(L)

A(R)

A(R)
A(L)

A(L)
Vcc

B(L)
REC–OUT(R)

(L)

(L)

55
XR-A770

•Pin Function
No. Pin Name Function No. Pin Name Function
1 VCC VCC pin 16 PB-Cal B (R)
Feed back input for gain adjustment
2 RECOUT (L) 17 PB-Cal B (L)
REC-EQ output
3 RECOUT (R) 18 PB OUT (R)
PB output
4 REC-RETURN REC return 19 PB OUT (L)
5 PB-IN B (L) 20 A/B
PB B deck input
6 PB-IN B (R) 21 HSP
Mode control input
7 VREF Reference voltage 22 Acr
8 PB-IN A (L) 23 Bcr
PB A deck input
9 PB-IN A (R) 24 REC-SEL Mode control input
10 PB-NF (L) 25 IREF Equalizer reference current input
PB EQ feed back
11 PB-NF (R) 26 AUX (R)
12 PB-EQ (L) 27 AUX (L)
NAB output REC-EQ input
13 PB-EQ (R) 28 TAPE (R)
14 PB-Cal A (L) 29 TAPE (L)
Feed back input for gain adjustment
15 PB-Cal A (R) 30 GND GND pin

LC75396NE (AF ASSY : IC3001)

• Electrical Volume IC
•Block Diagram

LTOUT
LF1C1

LF1C2

LF1C3

LF2C1

LF2C2

LF2C3

LF3C1

LF3C2

LF3C3

LF4C1

LF4C2

LF4C3
LTIN

LFIN
LF5

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33

LSELO 49 32 LFCOM

LINVIN1 50 31 LFOUT

L5 51 30 LRIN

L4 52 29 LRCOM

L3 53 28 LROUT

L2 54 27 LVref
LVref
L1 55 26 VSS

VDD 56 25 CE
CONTROL CCB
R1 57 LOGIC CIRCUIT 24 DI
CIRCUIT INTERFACE
R2 58 23 CL

R3 59 22 Vref
RVref
R4 60 21 RVref

R5 61 20 RROUT

RINVIN1 62 19 RRCOM

RSELO 63 18 RRIN

RTIN 64 17 RFOUT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
RF1C1

RF1C2

RF1C3

RF2C1

RF2C2

RF2C3

RF3C1

RF3C2

RF3C3

RF4C1

RF4C2

RF4C3

RF5

RTOUT

RFIN

RFCOM

56
 XR-A770

PDC049A (DISPLAY ASSY : IC5501)

• System Control Microcomputer
•Pin Function
No. Pin Name I/O Function No. Pin Name I/O Function
1 CD RESET O Reset output for CD LSI 51 VFDP –
2 CD CE O CD LSI strobe output 52 S*/D5593 *
3 CD DRF I RF level detection input 53 S*/D5592 *
BASSLED/LED
4 O LED control for P.BASS indicator (LED BASS) 54 S*/D5591 *
CE2
Clock output for EXP IC (BU4094), LED IC
5 EXP CLK O 55 S*/BJOGC2 I/O
(BU2092) and Prologic IC (LV1035)
Data output for EXP IC (BU4094), LED IC
6 EXP DATA O 56 S*/BJOGC1 I/O
(BU2092) and Prologic IC (LV1035)
EXP IC (BU4094), LED IC (BU2092) strobe
7 EXP CE O 57 S*/BJOGB2 I/O
output
8 LED1/SPE A O 58 S*/BJOGB1 I/O
LED control /
9 LED2/SPE B O 59 S*/BJOGA2 I/O
Spectrum analyzer IC (BU1923) output control
10 LED3/SPE C O 60 S*/BJOGA1 I/O
FL display control anode
AC pulse input
11 AC I 61 S* I/O
(for clock , power supply monitor)
12 XRESET I CPU reset input 62 S* I/O
13 REEL1 I Pulse input for deck 2 reel 63 S*/CLAMP I/O
14 REEL2 I Pulse input for deck 1 reel 64 S*/OPEN I/O
15 VS S – Ground 65 S*/INSIDE I/O
16 CF1 I 66 S*/CDISC123 I/O
17 CF2 O 67 S*/ARR I/O
18 VD D – Power supply 68 S*/ARF I/O
19 KEY1 I Front key input 69 S*/MODE1 I/O
20 MS I Deck MS signal input 70 S*/MODE2 I/O
21 ST/TUNE I Tuner tuned (STEREO) detection 71 S*/HALF1 I/O
22 TH I Temperature and protection circuit detection 72 VDD –
23 TIMER LED O LED control (for timer) 73 S*/HALF2 I/O
24 KEY2 I Front key input 74 S*/CrO2_1 I/O FL display control anode
25 SPE-IN I Spectrum analyzer signal input 75 S*/CrO2_2 I/O
26 KEY3 I Front key input 76 SCAN ON O Key scan input control
27 CD WRQ I CD subcode Q data OK signal input 77 SOL2 O Deck 1 solenoid control
28 RDS CLK I Clock input for RDS IC (BU1923) 78 SOL1 O Deck 2 solenoid control
29 REMOCON I Remote control signal input 79 MOTOR O Deck motor control
30 G* 80 RDSDATA I Data input for RDS
31 G* 81 VOLJOG1
I Pulse input for volume jog
32 G* 82 VOLJOG2
33 G* 83 PLL CE O Tuner PLL IC strobe output
Headphone SW detect input / Prologic IC
34 G* 84 HPSW/PRO CE I/O
(LV1035) strobe output
Main volume control IC (LC75394) strobe
35 G* 85 EVOL CE O
output
36 G* 86 POWER O Main power control
37 G* O FL display control anode 87 LINE MUTE O Line mute control
38 G* 88 LED CE O LED control IC (BU2092) strobe output
39 G* 89 VSS – Ground
40 G* 90 VDD – Power supply
41 G* 91 NC
I No connection
42 G* 92 NC
43 G* 93 MORP JOG1
I Pulse input for sound morphing jog
44 G* 94 MORP JOG2
45 G* 95 SYSDATA O Serial data output
46 VDD – Power supply 96 TXDATA I Serial data input
47 S*/D5597 O 97 SCLK O Serial clock output
48 S*/D5596 O 98 CD DATA O Serial data output for CD LSI
FL display control anode
49 S*/D5595 * 99 SQ OUT I Serial data (Q DATA) input for CD LSI
50 S*/D5594 * 100 CD CLK O Serial clock output for LSI

57
XR-A770

LC78622NE (CD ASSY : IC8301)

• CD DSP IC

• Block Diagram

TEST1
TEST2
TEST3
TEST4
TEST5
TST11
EFMO

VVDD
VVSS

VDD
ISET
PDO

VSS
PCK

TAI
FR
9 6 4 3 5 7 21 20 59 64 11 32 33 62 23 8

DEFI 1 Slice level VCO clock

control oscillator 2k × 8-bits RAM address
EFMIN 10 RAM generator
clock control

Sync Interpolation
mute 30 C2F
FSEQ 22 detection EFM
demosulation

CLV+ 12 CLV Digital C1, C2 error detection

CLV– 13 servo & correcting Flag Digital 31 DOUT
Processing output
V/*P 14
PW 49
SBCK 51 Sub core Digital
separation attenuator
SBSY 47 QCRC
SFSY 50
8 × oversampling
*CS 63 digital-filter
WRQ 53 Microcomputer
SQOUT 55 Interface
1-bit DAC
*CQCK 57
COIN 56 General
Servo purpose port Crystal oscillation L. P. F
RWC 54 commander system generator

15 16 17 20 19 58 18 34 24 25 26 27 28 29 48 60 61 46 52 45 44 43 39 41 35 40 37 42 38 36
HFL
TES
TOFF
JP–

EMPH/CONT6

16M
4.2M
XVSS
FSX
XIN
XOUT
XVDD
RVSS
RVDD
MUTER/CONT7

RCHO

LCHO
MUTEL/CONT8
JP+
*RES
TGL
PCCL
CONT1
CONT2
CONT3
CONT4
CONT5

EFLG

LVSS
LVDD
• Pin Function
No. Pin Name I/ O Function
1 DEFI I Defect detection signal (DEF) input pin (Must be connected to 0V when unused).
2 TAI I Test input pin A pull-down resistor is built-in. Must be connected to 0V.
3 PDO O External VCO control phase comparator output pin
4 VVSS − Internal VCO ground pin Must be connected to 0V.
PLL pins
5 ISET AI PDO output current adjustment resistor connection pin
6 VVDD − Internal VCO power supply pin
7 FR AI VCO frequency range adjustment
8 VSS − Digital system ground pin Must be connected to 0V.
9 EFMO O EFM signal output pin
Slice level control
10 EFMIN I EFM signal input pin
11 TEST2 I Test input pin A pull-down resistor is built-in. Must be connected to 0V.
12 CLV+ O Disc motor control output
13 CLV– O Can be set to three-value output by microprocessor command.
Rough servo/phase control automatic switching monitor output pin
14 V/*P O
Outputs a high level during rough servo a low level.
15 HFL I Track detection signal input pin This is a Schmitt input.
16 TES I Tracking error signal input pin This is a Schmitt input.
17 TOFF O Tracking off output pin
18 TGL O Tracking gain switching output pin Increase the gain when low.
19 JP+ O Track jump output
20 JP– O Three-value output is also possible when specified by microprocessor command.

58
 XR-A770

No. Pin Name I/O Function

21 PCK O EFM data playback clock monitor pin Output pin 4.3218MHz when the phase is locked.
Synchronization signal detection output pin
22 FSEQ O Output a high level when the synchronization signal detected from the EFM signal and the internaly generated
synchronization signal range.
23 VDD − Digital system power supply pin
24 CONT1 General-purpose 1
25 CONT2 General-purpose 2
Controlled by serial data commands from the microprocessor. Any of these that are
26 CONT3 I/O General-purpose 3 unused must be either set up as input pin ports and connected to 0V, or set up as output
pin ports and left open.
27 CONT4 General-purpose 4
28 CONT5 General-purpose 5
29 EMPH/CONT6 O De-emphasis monitor pin A high level indicates playback of a de-emphasis disk. / General-purpose 6
30 C2F O C2 flag output pin
31 DOUT O Digital output pin (EIJA format)
32 TEST3 I
Test input pin A pull-down resistor is built-in. Must be connected to 0V.
33 TEST4 I
General-purpose input / output command identifying pin
Must be connected to 0V when used with functions similar to those of LC78622E.
34 PCCL I
H: Control possible only for the general-purpose input / output port command
L: Control possible for all commands
35 MUTEL/CONT7 O Left channel mute output pin
36 LVDD − Left channel one-bit Left channel power supply pin
37 LCHO O D/A converter Left channel output pin
38 LVSS − Left channel ground pin Must be connected to 0V.
39 RVSS − Right channel ground pin Must be connected to 0V.
40 RCHO O Right channel one- Right channel output pin
41 RVDD − bit D/A converter Right channel power supply pin
42 MUTER/CONT8 O Right channel mute output pin
43 XVDD − Crystal oscillator power supply pin
44 XOUT O
Connections for a 16.9344MHz crystal oscillator element pin
45 XIN I
46 XVSS − Crystal oscillator ground pin Must be connected to 0V.
47 SBSY O Subcode clock synchronization signal output pin
48 EFLG O C1, C2 single and double error correction monitor pin
49 PW O Subcode P, Q, R, S, T, U and W output pin
50 SFSY O Subcode frame synchronization signal output pin This signal falls when the subcode are in standby state.
51 SBCK I Subcode readout clock input pin This is a Schmitt input. (Must be connected to 0V when unused.)
52 FSX O Output pin for the 7.35kHz synchronization signal divided from the crystal oscillator
53 WRQ O Subcode Q output standby output pin
54 RWC I Read/write control input pin This is a Schmitt input.
55 SQOUT O Subcode Q output pin
56 COIN I Command input pin from control microprocessor
Input for both the command input acquisition clock and the SQOUT pin subcode readout clock input pin.
57 *CQCK I
This is a Schmitt input.
58 *RES I Reset input pin This pin must be set low briefly after power is first applied.
59 TST11 O Test output pin Leave open. (Normally output a low level.)
60 16M O 16.9344MHz output pin
61 4.2M O 4.2336MHz output pin
62 TEST5 I Test input pin A pull-down resistor is built-in. Must be connected to 0V.
63 *CS I Chip select input pin A pull-down resistor is built-in. Must be connected to 0V if not controlled.
64 TEST1 I Test input pin No pull-down resistor. Must be connected to 0V.
Note: The same potential must be supplied to all power supply pins, i.e., VDD, VVDD, LVDD, RVDD and XVDD.

59
XR-A770

LV1035M (PRO LOGIC ASSY : IC3701)

• Dolby Pro Logic Decoder IC

• Block Diagram

NS-BPF1

NS-BPF2
C-MODE

ENABLE
DC-OUT
L-BPF2

L-BPF1

RT-IN

DATA

DATA
LT-IN

GND

OSC

CLK

CLK

VSS
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33

NOISE-GEN OSC

DATA-DEC
L-BPF3 49 32 OSC

NOISE-FIL
BPF

DEV
DCOUT3 50 R 31 OSC

L
SW7

VDD
R-RECT 51 30 VDD

BFL-CONT
A B
RECT

RECT

ADM-CONT
VOL

VOL

DCOUT4 52 29 A/D

ADM
LR

IN-FILTER
OUT-FILTER
23PIN
CH-CONT

L-RECT 53 28 NS

B-NR
LOGDIFF

S-RAM
A B A B

SW2 SW2 15PIN

VLR-TH 54 27 D/A
R

SW4
S C
D
VLR-1 55 B 26 DC-OUT

DC-OUT
PG

VCA

VCA

VLR-2 56 25 DC-OUT
C-MODE

VOL/MUTE
STRIM
B SW7
VCS-2 57 L 24 L-OUT
VCA

VCA

A
PG

B SW7
VCS-1 58 R 23 R-OUT
A B A
VCA

VCA

S-MODE

VCS-TH 59 SW7 S 22 S-OUT

LOGDIFF

VCA

VCA

L+R-RECT 60 21 GND
S

SW7
VCS

A B
DCOUT2 61 SW7 A B 20 IREF
RECT

RECT

A B
A B A B SW7
L-R-RECT 62 19 DET
S

SW4 SW3
R

L
CIRIM
BPF

DCOUT1 63 A B A B 18 VCC
R
L

SW6 SW5
13PIN

20kΩ

20kΩ
VREF

SW7 SW7
S

R-BPF3 64
C

R
S

17 DELAY-OUT
L

A B A B

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
R-BPF2

R-BPF1

S-DC-OUT

C-DC-OUT

R-DC-OUT

L-DC-OUT

VREF

VCC

C-OUT

S-OUT

R-OUT

L-OUT

AC-GND

L-IN

R-IN

S-IN

60
 XR-A770

7.1.2 DISPLAY
7 XAV3004 (DISPLAY ASSY : V5621)
• FL Display

• Pin Assignment
53 1

• Grid Assignment
1G 2G 3G 4G 5G 6G 7G 8G 9G

16G 15G 14G 13G 12G 11G 10G

s a1 a2 a1 a2 S6 S7

h j
f b
k
t g m
D2
r n B26 B13
u e c
p
D1 D1
w d1 d2 d1 d2
(2G) (2G to 9G) (7G) (9G) B20 B7

S4

S1
S3 B14 B1
S2 S5

(9G) (16G to 10G)

61
XR-A770

• Pin Connection
Pin No. 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
Connection F2 F2 F2 NP NP 1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 15G 16G P1 P2 P3 P4 P5 P6

Pin No. 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 NP NP F1 F1 F1
NOTE 1) F1, F2........... Filament
2) NP................ No pin
3) DL................. Datum Line
4) 1G to 16G..... Grid

• Anode Connection

1G 2G 3G to 6G 7G 8G 9G 10G to 16G
P1 – a1 a1 a1 a1 a1 B14
P2 a2 a2 a2 a2 a2 B15
P3 h h h h h B16
P4 j j j j j B17
P5 k k k k k B18
P6 b b b b b B19
P7 (Left) f f f f f B20
P8 g g g g g B21
P9 (Right) m m m m m B1
P10 (Upper right) c c c c c B2
P11 e e e e e B3
P12 r r r r r B4
P13 p p p p p B5
P14 n n n n n B6
P15 (V-CD) d1 d1 d1 d1 d1 B7
P16 d2 d2 d2 d2 d2 B8
P17 s – – – S7 B22
P18 (Under) t – – – S2 B23
P19 (PBC) u – – – S3 B24
P20 w – – – S4 B25
P21 – – – – S5 B9
P22 – – – – B10
P23 – – – – B11
P24 – – – – B12
P25 D1 D1 D1 D1 B26
P26 – – – D2 – B13
P27 – – – S6 – – S1

62
 XR-A770

7.2 DISASSEMBLY
$M MECHANISM CD

2 1 ×3 1 ×3
Bonnet Case

1 ×3 4

1 ×3
7 ×2

1 ×3

Tray Cap

Main Cam 5 ×3
Unhook
Note: The loading tray can be pulled out
when the main cam is in this position.
(The Lock Lever should be in the
3 notch of the Main Cam.)

Fitting

Lock Lever

12
$M Mechanism CD

10
Release the jumper wire
from Cord Stopper.

11

63
XR-A770

FRONT PANEL

1 Unhook

2 Unhook

CD SW LED Assy
FM/AM TUNER MODULE

AF Assy

Front Panel

DISPLAY Assy

SUB TRANS Assy Mechanism Unit

4 Release the jumper wire
from Clip B.
SUB DISPLAY Assy

3 5
PRIMARY Assy
SECONDARY Assy

$M MECHANISM CD ADDITIONAL TO JOB

Mechanism Base (Bottom View)

Front Side

2
1

64
 XR-A770

Clamper Holder Servo Base

1 Servo Mechanism 1
Clamper Holder Assy Hook
2 1 Hook Servo Base
2
Hook

$M Mechanism CD

Actuater

Actuater

1
Hook

FITTING THE PULLEY INTO THE CARRIAGE MOTOR

For replacement of the carriage motor,
fit the motor pulley by using the servicing
pulley press-in station located on the loading
tray, as shown in the figure on the right. Carriage Motor

Motor Pulley

Servicing pulley press-in station

Loading Tray

65
XR-A770

7.3 BLOCK DIAGRAM

DUMMY
A
53
TUNER
MODULE
E IC3001 ZOOM BASS
LC75396 SURROUND BLASTER
(-2dB) -
CD B 55 +
$ MECH (-8dB)
-
AUX +
(200mV) 52 -
+ BASS
TREBLE

TAPE
DECK 54
(-3.8dB)

50 49 45 46 48 47 35

(+2dB) (-6dB)
45 PROLOGIC 24
LV1035M

N IC3701
22 To R ch From R ch

BASS
REAR CENTER BLASTER
TRIM : -10dB

TAPE
DECK
E Q2301
HA12211NT
E IC2301
E IC2201
FUNCTION
5
TAPE + + 19 + 14 - 11 +
DECK - - +
PB
HA12136AF
4 Vref DOLBY NR
Vref
Vref

Vref Vref
E VR2305

66
 XR-A770

E IC3381
E
(XR-A880 : +5dB) IC3301
(XR-A770 : +8dB) POWER AMP E
2 RY3601 FRONT
- 14 7
31 TOTAL GAIN
+ 1
+42dB

STK407-090
(+40dB)
HEAD
PHONE
E CN3991

28
L IC3401
34 33 30 POWER AMP
3 REAR
- 1 4
E XR-A880 ONLY
+ 1
CENTER
TWEETER
IC3951
E IC3421 TDA8560Q
E (XR-A880 : +9dB) (+40dB)

IC3202 (XR-A770 : +5dB)

LPF
2 - 1
+

2 - 1 DOLBY
+ PROLOGIC OFF
HPF
E IC3201
DOLBY
PROLOGIC ON
E IC3203
XR-A770 ONLY

TAPE
DECK
E IC2201 E IC2301
MPX - + + 27 - 2 +
REC IN + 16 9
+ TAPE
+
DECK
REC
HA12136AF
DOLBY NR
E VR2301
HA12211NT
E F2201 Vref Vref Vref
Vref

67
XR-A770

8. PANEL FACILITIES AND SPECIFICATIONS

• PANEL FACILITIES
456 7 8

¤ 9 1 2 3

-
™
=
~
!
£
@ §
∞
# ¶
$ ¢
%
•
_
ª
+

^ & * ) ( ¡ º Ÿ ⁄ ≠ –

1 DISC-1 indicator + TAPE I cassette door

2 DISC-2 indicator ¡ Dolby** Ÿ NR ON/OFF button
3 DISC-3 indicator ™ Volume control (VOLUME)
4 DISC-1 select button £ DISPLAY/RDS button
5 DISC-2 select button ¢ ENTER button
6 DISC-3 select button ∞ S.M. JOG (Sound Morphing JOG)
7 DISC CHANGE button § TIMER / CLOCK ADJ button
8 OPEN / CLOSE button ¶ PHONES jack (Headphones)
9 Display • TAPE II Eject button (0)
0 CD disc tray ª TAPE II cassette door
- CD Function button & indicator º BASS BLASTER button & indicator
= TUNER / BAND Function button & indicator – PRESET button & indicator
~ TAPE I / II Function button & indicator ≠ EQUALIZER button & indicator
! AUX Function button & indicator Ÿ ZOOM SURROUND button & indicator
@ STANDBY indicator ⁄ BLANCE (DEMO) button & indicator
# STANDBY / ON switch ¤ TIMER indicator
$ TUNNING 1 4 - button * Lights in Standby mode when the system has been set for
timer operation.
% TUNNING + ¢ ¡ button *
^ STOP (7) button *
& PLAY / PAUSE , MEMORY button *
*÷ This button functions differently with CD, TUNER/BAND or TAPE
* REC / STOP button
( FREQ / STATION button I/II function.

) ASES / COPY button **

÷ Dolby noise reduction manufactured under license from Dolby
_ TAPE I Eject button (0) Laboratories Licensing Corporation.
÷ “DOLBY” and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.

68
 XR-A770

6 5 7 - !

%
=
0
9
$

8 #

Display section
5 Displays timer function indications.
6 Indicates CD function status.
7 Lights during recording.
8 Lights during ASES operation.
9 Lights during Sleep Timer operation.
0 Indicates tuner operation status.
- Displays a wide range of operation status indications.
= Lights when BEAT CUT 2 is selected.
! Indicates SOUND MORPHING status.
@ Indicates TAPE status.
# Displays Audio level, spectrum analyzer and other
indications.
$ Indicates CD player operation status.
% Lights when the RDS mode is selected.

FRONT PANEL For moders XR-A770

60 Hz 120 Hz P.BASS ON/OFF WOOFER

level level button/indicator LEVEL control
control control

69
XR-A770

Function button section REMOTE CONTROL UNIT

1 0

2
1 2 3 -

1 3 =
~
2 4
5 !
3 6 @
4 #
5 6 7 7 $
8
%
9

^
1 CD function button
&
2 TUNER/BAND function button
3 TAPE I/II function button
4 AUX function button
5 TUNING [1,4 (–), (+) ¢,¡] buttons
6 STOP button (7)
7 PLAY/PAUSE button (2 3)

÷ Roles of the common operation buttons (The rules of

the buttons vary depending on the input functions as
shown below.)

During CD input
PLAY/PAUSE: Play/pause button
STOP: Stop button
(+) ¢,¡: Fast forward/track search button
1,4 (–): Fast reverse/track search button

During cassette deck input

PLAY/PAUSE: Play button/Tape transport direction
STOP: Stop button
(+) ¢,¡: Fast forward button/Music search button
1,4 (–): Rewind button/Music search button

During tuner operation

PLAY/PAUSE MEMORY: STATION MEMORY button
(+) ¢,¡: Frequency & Station + (up) button
1,4 (–): Frequency & Station – (down) button

7 Auto Play Function

If you press the CD function button when a CD is loaded, the CD
automatically starts playing. If you press the TAPEI/II function button
when a tape is loaded in the cassette deck, the tape automatically
starts playing.

NOTE:
The function cannot be switched during recording and tape copying.

70
 XR-A770

REMOTE CONTROL UNIT

1 OPEN/CLOSE button
2 DISC CHANGE button
3 PGM button
4 SLEEP timer button
5 TAPE I/II function button
6 AUX function button
7 MONO button
8 BASS MODE button
9 MORPHING MODE button & MORPHING jog control
buttons
0 STANDBY/ON button
- DISC select buttons (1–3)
= CLEAR button
~ Numerical buttons
When using for radio station tuning:
Pressing these buttons tunes the unit to the frequencies stored in
memory.
Examples:
Station 5
Station 13
Station 20
When using for the CD player:
Pressing these buttons lets you directly select the tracks you want
from the program you entered.
Examples:
3rd track
99th track
! REPEAT button
@ RANDOM button
# CD function button
$ BAND button
Use to switch between FM and AM bands.
% CD/TAPE/STATION (up/down) operation buttons
÷ CD operation buttons
(Play/Pause 3/8, Track search 4 ¢, Stop 7, Fast 1 ¡)
÷ TAPE operation buttons
(Play 2 3, Music search 4 ¢, Stop 7, Fast 1 ¡)
÷ TUNER buttons
+ ........... Stations change in order in the upward direction.
– ............ Stations change in order in the downward direction.
1 ........ Frequency down.
¡ ........ Frequency up.

^ VOLUME 5 (up), ∞ (down) buttons

& DISPLAY button

71
XR-A770

• SPECIFICATIONS
Continuous Power Output Miscellaneous
XR-A770 Power Requirements ................................. AC 220-230V, 50/60 Hz
Woofer (RMS) ...................................................... 120 W + 120 W Power Consumption
(100Hz, T.H.D. 10 %, 6 Ω) XR-A770 .............................................................................. 230 W
Woofer (DIN) ............................................................ 80 W + 80 W Power Consumption in standby mode ....................................... 1 W
(100Hz, T.H.D. 1 %, 6 Ω)
Tweeter (RMS) ......................................................... 30 W + 30 W Dimensions
(3 kHz, T.H.D. 10 %, 4 Ω) XR-A770 ..................................... 270 (W) x 380 (H) x 343 (D) mm
Tweeter (DIN) .......................................................... 20 W + 20 W Weight (without package)
(3 kHz, T.H.D. 1 %, 4 Ω) XR-A770 ............................................................................... 10 kg

÷ Above specifications are for when power supply is 230 V. Accessories

Operating instructions .................................................................... 1
Music Power (DIN) Remote control unit ........................................................................ 1
Size AA/R6P dry cell batteries ....................................................... 2
XR-A770
FM antenna .................................................................................... 1
Woofer ................................................................. 168 W + 168 W
AM loop antenna ............................................................................ 1
Tweeter .................................................................... 23 W + 23 W
Power Cord .................................................................................... 1
÷ Above specifications are for when power supply is 230 V.

FM/AM Tuner section NOTE:

FM tuner section Specifications and design subject to possible modification without
Frequency Range ......................................... 87.5 MHz to 108 MHz notice, due to improvement.
Antenna input ........................................................ 75 Ω unbalanced
AM tuner section
FrequencyRange ............................................ 531 kHz to 1,602kHz
Antenna input ............................................................. Loop antenna
CD section
POWER-CORD CAUTION
Type ........................................... Compact disc digital audio system
Wow and Flutter ............................................. Limit of measurement Handle the power cord by the plug. Do not pull out the plug by
(±0.001 % W.PEAK) or less (EIAJ) tugging the cord and never touch the power cord when your hands
Cassette deck section are wet as this could cause a short circuit or electric shock. Do not
Systems .................................................... 4 track, 2-channel stereo place the unit, a piece of furniture, etc., on the power cord, or pinch
Heads ................................................. Recording/playback head x 1 the cord. Never make a knot in the cord or tie it with other cords.
...................................................................... Playback head x 1 The power cords should be routed such that they are not likely to
........................................................................ Erasing head x 1 be stepped on. A damaged power cord can cause a fire or give
Motor ................................................................. DC servo motor x 1 you an electrical shock. Check the power cord once in a while.
Tape type When you find it damaged, ask your nearest PIONEER authorized
XR-A770 service center or your dealer for a replacement.
.................... TYPE I (Normal) tape / TYPE II (HIGH/CrO2) tape

1 2 3 4 5 For MYXJ type

1 2 3

KARAOKE

For NVXJ type

1 Remote control unit x 1 : XZN3007 (CU-XR049)

2 FM antenna x 1 : ADH7005
3 AM loop antenna x 1 : XTB3001
4 AA/R6P dry cell batteries x 2
5 Power Cord x 1 : ADG1154 (MYXJ type), ADG1156 (NVXJ type)

72