UNIPARKER N5002-IS
No columns at the entry level
so increased accessibility
Made in Germany
Area of application:
residential buildings, hotels and office buildings
Platforms are
horizontally
accessible.
Load per platform
max. 2000kg
Load per wheel
max. 500kg
Functional description
The moving platforms in the pit and in the top level execute horizontal movements at
the entrance level. The cylinder-controlled piston stroke sledge, with which these
platforms are connected rigidly, effect a quiet run.
The sliding platforms to slide sideways in the entrance level run on rail-controlled
rollings. By the use of the empty space (one sliding platform under number of segments)
the movement of the moving platforms is provided.
The operation function by the use of the push button, with which the respective parking
space will be dialled. In the automatic operation the platforms move when the gate is
closed. The corresponding gate is approved to drive in and drive out of the system if
the dialed platform stand by.
Technical data
pit pit column car height car height
in front at rear clearance height below above
175 175 220 365 150 205
185 185 220 385 160 205
200 200 220 415 175 205
210 210 230 435 185 215
220 220 240 455 195 225
230 230 250 475 205 235
standard
The memtioned above details to the vehicle height are maximum dimensions.
Columns only at the rear panel = direct power transmission:
less moving parts and high operating safety
Vehicle data
8 162 65 55 90 8 162 115
10
25 20 15
150 150
46
46
56
22 60 27 56 22 27
38 14 14
38 60
90 max. 290 120
90 max. 290 120
500 500
Standard: car width max. 190cm, vehicle weight max. 2000kg, wheel load max. 500kg
Optional vehicle data: car length up to 520cm, vehicle weight max. 2600kg, wheel load max. 650kg
Width dimensions
platform raster raster total width dimensions B by x segments
width outer inner 3 4 5 6
230 260 250 770 1020 1270 1520
240 270 260 800 1060 1320 1580
250 280 270 830 1100 1370 1640
standard
Positioning of the segments
The smallest unit are 2 segments for 3 cars. The system can be extended in any order. But we recommend to
position not more than 10 segments for 19 cars side by side with one common hydraulic unit.
Advantages of Uniparker N 5002-IS
Per segment are two columns at the rear panel only. column is fixed between the both segments. The IS-
In the entrance level no columns are needed. By the System needs less maintenance effort in comparison
loss of these columns the driving into and driving out to competition car parking systems: The Uniparker-IS is
of the system is considerable eased. void of power transmission parts such as chains and ropes.
All vertical platforms are driven directly with hydraulic
The stability of the N 5002-IS is guaranteed. This cylinders. Thus the need for springs, tensioners, slack
means that the columns behind will be fixed at the switches and other safety mechanisms related to chains
rear panel and in addition a horizontal bent column and ropes are eliminated; less to go wrong. The vertical
is assembled. This bent column initiate from the platforms are also equipped with a warp and bend
behind left column and the behind right column of resistant frame rail which anticipates accidental lowering
two segments up to the pit front edge. The bent making additional locking mechanisms unnecessary.
Features in the scope of delivery
Scope of supply
Installation with sliding platforms and one empty space
on the entrance level, on top and in the upper level with
vertical moving platforms. Completely with hydraulic
driving elements and electrical control elements.
Drive of the platforms
2 lifting cylinders to drive the horizontal moving platforms
with direct power transmission and without supporting
Control element parts (as chains and ropes), sliding platforms with electrical
Touch Screen with key-switch, emergency stop drive.
in dead man´s control with brief operating
instructions and wiring to the hydraulic unit. Width of parking space
Width of parking space 230cm, pit depth 175cm and
Hydraulic unit clearance 220cm as standard
Hydraulic unit “Silencio“
with tubing and wiring to Safety devices
the installation. The oil • entering wedges for easy drive-in and parking
submerged motor is • mechanical locking device prevents lowering by
extremely quiet and smooth pipe breakage
running. The motor-pump • fixation of the installation and the hydraulic unit
assembly is sound absorbent. with HD-anchors, wiring and impact dowels
Sliding gates
Location Sliding gates for fall-danger prevention into pit and
According to the local requirements – railings for fall-danger prevention from the platform.
preferable placed near the rear columns/ (Notice: safe guarding against shearing and squeezing
cylinders have priority and must provided by the prorietor sideways
Dimensions: approx. 60 cm x 22cm x 40 cm and behind the installation)
We recommend, according to the access times,
Protection against corrosion
to use max. 10 segments with one hydraulic unit.
• Corrosion protection “Classic“ of driving plates by
continous line-galvanizing to DIN EN 10142/10143.
• Corrosion protection “Classic Plus“ of driving plates
by line-galvanizing and powder coating to DIN EN
10142/10143 and surface coating on top (depending
on the market specific needs zinced and powder coated
sheet metal included in the scope of supply).
Driving plates
Driving plates as trapezoidal sheet plates as
standard, options see “Extra Equipment“.
Extra Equipment and Options
Width of parking space
Width of parking space 240cm and 250cm is recommended
for even more vehicle comfort.
Vehicle weight
Optional vehicle weight: up to 2600kg
Additional sound insulation
• structure-borne noise package to comply with DIN 4109
and adherence to sound insulation-measure Rw ´57
Driving plates • sound insulation hood to minimize airborne sound
Alu-bulb-plate in the walking area even more
user friendly when walking and driving. Hydraulic
• HVLP 32-330 oil for high fluctuations in temperature
Installation of gates
See detail, page 7
Ramp by installation of gates
Ramp by installation of gates behind the columns,
pit length must be minimum 560cm
Remote control for gates
Remote control and/or automatic-drive for sliding gates
Protection against corrosion
Catwalks • Corrosion protection “Premium“ of driving plates by
Positioning on the left side of the parking individual piece-galvanizing to DIN ISO 1461.
space even more comfortable, when walking to • Corrosion protection “Premium Plus“ of driving plates
the driver´s door. 1,5 mm zinced sheet, surface individual piece-galvanizing to DIN ISO 1461 and
are coined. The catwalks are screwed to the coating of the top surfaces.
driving plates, available with corrosion
protection version “Classic“ or “Classic Plus“. Tips
• We recommend a maintenance contract.
Modem for Teleservice/Online diagnosis • Attendance & cleaning according to recommendations
With the Nussbaum CAN-BUS control system or in regular intervals.
(delivery includes modem) remote maintenance
and tele-service are possibilities.
This allows the Nussbaum parking experts a
“tele-presence” at the customer in a matter of
seconds for analysis and support.
(on site: modem/DSL connection Euro-DSL SO).
Interfaces to be performed by the Buyer
Foundation
Foundation works exactly to size, clean and dry is to be completed by the start of the installation. Bonded anchors
for high foundation requirements shall be provided if neccessary, available also as option.
Foundation plan
back wall detail X
F1 F1
X X
3 dowel holes
per
base plate
20
L
L
support against pit edge, in front
F2 F2 F2 F2
20
R1 R R1
driving lane
platform raster raster outer length force moment
width R R1 L F1 F2
230 250 260 560* 45 kN 60 kNm
240 260 270 560* 45 kN 60 kNm
250 270 280 560* 45 kN 60 kNm
Dimensions in cm. *550 on request
Electrical data General costumers duties
• capacity of the hydraulic unit: 400volt, 50 hz, • level surface (H x W) 25cm x 26cm to attach the
three-phase motor 3,0 kW, mounting in the control panel, close to the system, outside the
immediate nearness of the Car Parking System platform area
• supply line to switch cabinet 5 x 2,5mm² , or to • safeguarding according to DIN EN 294
local requirements, fuse protection 3 x 16 amp, • lighting according to DIN 67528, illumination of
slow parking lots and buildings for parking
• electrical potential equalisation (foundation • 10cm wide, yellow-black marking in front of each
grounding steel-construction to VDE 0100 T410) segment according to ISO 3864, insofar that no
• telephone line dto by modem and teleservice/ gates are installad
online analysis available on request • compliance with installation requirements as per
• free space for switch cabinet LWH approx. quotation
60 cm x 22 cm x 80 cm, with pivot door in direct • foundation works exactly to size, clean and dry
near of system (max. 6 m) with access to the
parking system
Gates for fall-danger prevention into the pit (in the scope of delivery)
Gates according to DIN EN 14010
According to DIN 14010 the CarParkingSystems Uniparker N 5003-IS must be closed with shutterdoors. The gate controls are
integrated in the overall system.
Layout sliding gates
sliding platforms entrance level moving platforms in the Fixation of the gates: clearance max. 210 cm
upper level
und untere Ebene
Layout A
Sliding gates between pillars, columns supplied
by the employer min. every 2 segment, otherwise
assembly of gates in front of the column
Layout B
Sliding gates in front of pillars
Layout C
Sliding doors behind pillars: The employer must
consider the pit length of 560 cm behind the door
step of his sliding door.
pit edge C C
B
Electrical installation
Installation diagram, fig. 2 segments for 3 cars
9 9 switch cabinet
2 1
11
3
empty space
5,6
to slide sideways
7
10
M
4
Modifications are reserved to CarParkingSystems . PROSPEKT UNIPARKER N5002-IS-E · Version 10122007 · NK
Item Performance Quantity Designation Location Frequency
1 on site 1 fuse or automatic circuit in the feed cable 1x per system
3 x 16 amp slow to DIN VDE 0100 part 430
2 on site 1 feed cable 5 G 1,5 mm² or in the feed cable 1x per system
to local requirements to the switch cabinet
3 on site 1 potential equalization to DIN EN 60204 from foundation earth 1x per system
connector to the system
4 CPS 1 hydraulic unit with 3-phase motor 400 volt, 50 Hz 3 Kw
5 CPS 1 supply line 5 G 2,5 mm² with motor connector hydr.
marked wires and protective conductor unit to switch cabinet
2
6 NCPS 2 control line 2 x 1
7 NCPS 2 hydraulic valve
8 NCPS 1 segment box
9 NCPS 2 segment valve moving platform
10 NCPS 1 electrical motor
11 NCPS 1 control element with emergency stop
The items 4-11 are included in the scope of supply, unless otherwise specified in the offer/order.
CarParkingSystems - [email protected] - http://carparkingsystems.pt.to
