Xtralis Refrigerated Storage
Sampling Kit VSP-860 & VSP-860-US
Features & Benefits
• Enables the ASD pipe to be installed,
h inspected and maintained outside the
Refrigerated Storage facility hence
enabling fire contractors to work in ambient
conditions most of the time
Item No Description • Suited for facilities with and without ceiling
a Inlet Funnel cavities
g
b Inner Flange • Eliminates the need for expensive HDPE
c Outer Flange (high density polyethylene) pipe inside the
g
f Refrigerated Storage facility
d Screw self-tapping
d • Eliminates the need for costly access
i e Tube - Lower equipment hire for on-going service/
e
Socket Union - including maintenance
c f
Flow Restrictor and Seal
Cold Store
• Eliminates the need for heat tracing
Insulation Material g Tube - Upper
• Less prone to blockage due to icing
h Flexible Pipe
• Provides a generally more robust ASD
i US Pipe Adaptor installation for these unique environments
• Provides considerably improved aesthetics
• Minimises the need for “Back Flush”
systems
b • Offers all round cost savings
a
Overview Detectors Supported
The Xtralis Refrigerated Storage Sampling Kit provides a standardised method • All Xtralis detectors installed with large
of smoke sampling for Refrigerated Storage facilities in a considerably improved bore pipe networks.
manner allowing simplified installation with reduced maintenance, thus
promoting more reliable and hassle-free operation.
The Xtralis Refrigerated Storage Sampling Kit has been designed to replace
standard cone-shaped sampling nozzles installed at the ceiling in existing
or new Refrigerated Storage facilities. This kit can be installed in the entire
facility or combined with standard sampling points if required. The aim
here is to reduce direct ice blockage of the sampling points hence this kit is
recommended for installation in areas where higher humidity is likely to occur
as a result of vehicle and pedestrian traffic (e.g. areas close to doorways or
perimeter of the facility).
This kit is treated as a standard sampling hole in the Xtralis ASD system design,
in terms of system parameters (e.g. sampling hole location, hole size, transport
time, sampling hole sensitivity).
Description
The sampling kit consists of outer and inner parts with the sampling pipe
penetrating the Refrigerated Storage sandwich panel. The sampling pipe
through the sandwich panel and inner parts are made of ABS plastic which
is suitable for low temperatures down to -40 °F (-40 °C). The kit comprises a
restriction assembly, placed above the sandwich panel, which consists of a
sampling orifice within a socket union.
Xtralis Refrigerated Storage
Sampling Kit VSP-860 & VSP-860-US
Dimensions
Flexible pipe length
approximately 72 cm
100 mm
34 mm
280 mm
40 mm
100 mm
Ordering Information
Description Part Number
Refrigerated Storage Sampling Kit * VSP-860
Refrigerated Storage Sampling Kit - US VSP-860-US
In-line Flow Restrictor Assembly VSP-870
In-line Flow Restrictor Assembly - US VSP-870-US
Flow Restrictor Disc (pack of 10) VSP-871
* Please ensure a suitable T-junction is used, contact your local Xtralis office for further support.
www.xtralis.com
UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 The Americas +1 781 740 2223
Middle East +962 6 588 5622 Asia +86 21 5240 0077 Australia and New Zealand +61 3 9936 7000
The contents of this document are provided on an “as is” basis. No representation or warranty (either express or implied) is made as to the completeness,
accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or specifications without obligation and without
further notice. Except as otherwise provided, all warranties, express or implied, including without limitation any implied warranties of merchantability and
fitness for a particular purpose are expressly excluded.
Xtralis, the Xtralis logo, The Sooner You Know, VESDA-E, VESDA, ICAM, ECO, OSID, HeiTel, ADPRO, IntrusionTrace, LoiterTrace, ClientTrace, SmokeTrace,
XOa, XOh, iTrace, iCommand, iRespond, iCommission, iPIR, and FMST are trademarks and/or registered trademarks of Xtralis and/or its subsidiaries in the
United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks of their respective
holder(s). Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/or label.
This document is subject to copyright owned by Xtralis. You agree not to copy, communicate to the public, adapt, distribute, transfer, sell, modify or publish any
contents of this document without the express prior written consent of Xtralis.
Doc. no. 27506_01 Part: 30596
