This wiring diagram should be used only for course purposes! It is not covered by update services!

For training
purpose only!

This document is not under

control of any update service!
 Test certificate of I.I. inside CCD camera with mechanical rotation +/- 220°
logbook attention: 50Hz & 60Hz version available
old: SIMOMED Monitor
or M44 Hitachi(not
100 / 120 Hz delivered anymore!
manual iris with older
Upgrade to TFT available!
Compact < 1417
motorized
+/- 220 ° D4
M61

Not used with

SMISO C

Dicom
Connect*1 M13 M10 FU D1KV/mA control
X10 Master CPU
D2 invert board
TV only only
ISO-C ISO-C
BAS signal 15 Khz - 30 KHz
50 Hz / 60 Hz
error & status messages

50/60 Hz

Mon A
Mon B
Video

Power on x-ray tube

D50
displayed on X - iris, Slot diaphram
Monitor &CEX

Memmoskop CE / 3 images
100 V AC up to Memmoskop C100 /100 images
240 V AC Memmoskop C 700
Memmoskop C SUB /900 images
Memmoskop CX 200 up to 5000 im.
(integrated network interface)
 Monitors: 50 Hz Start video recorder
60 Hz release signal to MFK
100 Hz release s. to videoprinter
120 Hz

1Vpp /75 Ohms

Enable DICOM
bridge Video recorder
in the technical
setup menu 17!

DICOM Connect
Image data
From CCD camera
board D4 50/60 Hz
BAS, 1Vpp, 75 Ohms

only one of the

connections is used.

to hospital network

D 50
Barco monitors

CX 200
DICOM

RJ 45 to Hospital network

D 50
 after 180 ms ON
main transformer to D2
100 V AC -
board
NTC NTC
240 V AC 190 V AC

utility transformer

On keyboard
24 V
24 V

K2 + K3 ON T1 gets
power. (soft start)
Self holding
contact
After switching off K4 turns ON 150 ms
there is a waiting later (full power)
time(5s) until Lifting magnet for
swiching on is the diaphram gear
again possible. box.
 power supply
for D1 / D2

See
former TV power
page supply

Image intensifier
power supply N61

D 30 in ISO_C
Master CPU
board

vertical sync. High tension on

controlled

High tension ON request

Memmoskop
D4

Sync separation stage

Video BAS
 Master CPU
Inverter board
board

D16 is with
older
Diamentor
available

D30 with
SIREMOBIL
ISO-C

D4
To TV
camera
K4 Zoom relay

To I.I. mini
power
supply

Lifting column motor

Diagram used and valid only for SIREMOBIL COMPACT

Switches are
located inside
the column drive

Diagram used and valid only for SIREMOBIL COMPACT L

 high
tension
control

filament
control
kV+
>50C° 5mA curve off(keyboard display on)
kV-
>60C° 3mA
>70C° radiation off(keyboard display flashing

actual value

index switch
(zero position)

encoder for
actual position
of collimator
switch over the gear box
from open/close to
rotation of X- iris

Build in laser light

localizer inside
collimator.
(enabled via
service program)

xxx
In older
systems D16
is included

xxx

xxx: multiplication factor for the Dose area product

see service instructions.
 For dose
control
(actual
brightness
value)

1Vpp / 75 Ohm
D4 To MEMOSKOP
Automatic dose rate
control is switch of and
X iris goes to max
opening
(only SMC/L)

D4
+/- 220°

10 KOhm

0°
position
camera
board

TV iris actual
opening

Mini power
supply
Image
intensifier II
The newer SIREMOBIL COMPACT's can be delivered with a build in LASER LIGHT LOCALIZER at the Image Intensifier. If so, the former Cassette switch cable is used. The cable
connection " M4.X45 1/2 " is than connected to " Z66 X1A 10/3 " as shown in the diagram below.

With Cassette option Without Cassette option

Cassette switch

K1

K7 should be enabled via the service

programm
 D16 with older
emergency
systems
switch

actual
values

KV, mA act. serial interfaces

RS 232

Mini OS for
download
Memoskop

Slot
diaphragm

Filament curves Nominal Values

drive 10 drive 20

Firmware (Loadware) is on For more explanation see page 30 B/C

Parameter disk
 6 MHz
24 MHz

Single tank

15 KHz to
30 KHz

80 ms xray
extension

LIH
From 260 V DC Intermediate voltage
M50/D50 SIREPHOS
High tension
190 V ~

HT

Current
Filiament Temp. sensor
current Pressor switch

Short circuit test (standby

mode)
possible between X3 /3 / 1

Go to timing diagram page 29

drive 10 / 20
Monitoring

KV nom KV act
 Go to page 32 for camera
board layout!

Monitor
Used for doserate 8 bit brightness
µP control signal

Dominant

B-signal

MP: X8

KV/mA max: > Iris controlled

M4.X1
KV/mA max: Iris fully open > AGC on

Standard BAS-signal
Selfcheck 1Vpp / 75 Ohm
LED Sync. separation
110KV
stage

To Memmoskop

Gamma
40KV AGC Serviceprogram:
correction
"inputs setting" for
4.1mA X-ray tube TV iris
0.2mA CCD 512 matrix test images from
Memmoskop
S3: Only used when flash promms are empty to support download procedere!
 Rotateable: +/-220°

In 0 psoition

X1
Zoom
selection

E3

D120
 D120

From D xx
I.I. Calibration certificate is inside
log book