Scribd
Upload
48 views4 pages

Al Burj

This document contains the results of a concrete column design analysis for a lighting pole foundation using the ASDIP Concrete 4.4.8 software. Key details include: - The column has a width of 60 cm, height of 60 cm, and clear length of 1 m. - Reinforcing steel with a yield strength of 400 MPa will be used. - The controlling load combination produces an axial load of 1.4 kN and no bending moment. - The analysis calculates section properties, steel stresses and strains, and checks the column's bending and shear capacities against the loads. - The column is found to have an adequate design flexural strength of 367.9 kN-m to resist

Uploaded by

mido medo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views4 pages

Al Burj

This document contains the results of a concrete column design analysis for a lighting pole foundation using the ASDIP Concrete 4.4.8 software. Key details include: - The column has a width of 60 cm, height of 60 cm, and clear length of 1 m. - Reinforcing steel with a yield strength of 400 MPa will be used. - The controlling load combination produces an axial load of 1.4 kN and no bending moment. - The analysis calculates section properties, steel stresses and strains, and checks the column's bending and shear capacities against the loads. - The column is found to have an adequate design flexural strength of 367.9 kN-m to resist

Uploaded by

mido medo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Your Company Name Project: Lighting Pole Foundation Design Page # ___

Engineer: Ahmed Khalifa 30-Jun-21


Descrip: Lighting Pole Foundation Design
ASDIP Concrete 4.4.8 CONCRETE COLUMN DESIGN www.asdipsoft.com

Width ..... 60.0 cm , Height .... 60.0 cm Clear Member Length Lu ............ 1.00 m
, ρ = 0.011 OK Effective Length Kx-factor .......... 2.10
d' = 6.8 cm OK Effective Length Ky-factor .......... 2.10
Concrete Clear Cover ............. 5.0 cm Lateral Stability ...............
Slenderness Ratio = 12 < Limit = 22, Short

Dead Live RLive Snow Wind Seismic


Axial Force P .............. 0.5 0.5 0.0 0.0 0.5 0.0 KN
Mx at Bottom ................ 0.0 0.0 0.0 0.0 0.0 0.0 KN-m
Mx at Top ...................... 0.0 0.0 0.0 0.0 0.0 0.0 KN-m
Story Axial Force ΣP .. 79600.9 8856.4 1201.0 0.0 KN
Story Shear Force Vsy 1346.0 0.0 KN

Concrete f'c = 30.0 MPa Max. strain = 0.0030 Stress-strain = Hognestad


Young's Modulus ½ ½
4700 * (30) = 25743 MPa ACI 19.2.2.1
Rupture ½ 0.62 * (30)½ = 3.4 MPa ACI Eq. (19.2.3.1)
Steel fy = 400.0 MPa Stress-strain = Elasto-plastic Es = 199955 MPa ACI 20.2.2.2
Radius of gyration rx = 17.3 cm Radius of gyration ry = 17.3 cm
Slenderness ratio x = 2.10 * 1.00 * 12 / 17.3 = 12 ACI 6.2.5
Slenderness ratio y = 2.10 * 1.00 * 12 / 17.3 = 12 (governs)
Slenderness limit = 22 > 12, Short ACI 6.2.5
Max. tie spacing = Min(48 dt, 16 db, width) = Min(48 * 1.00, 16 * 1.60, 60.0) = 25.6 cm ACI 9.7.6.4.3

1 of 4
Your Company Name Project: Lighting Pole Foundation Design Page # ___
Engineer: Ahmed Khalifa 30-Jun-21
Descrip: Lighting Pole Foundation Design
ASDIP Concrete 4.4.8 CONCRETE COLUMN DESIGN www.asdipsoft.com

Controlling load combination: 1.2D+1.6L+0.5Lr


Axial load Pu = 1.2 * 0.5 + 1.6 * 0.5 + 0.5 * 0.0 + 0 * 0.0 + 0 * 0.5 + 0 * 0.0 = 1.4 KN
Mux gravity bot = 1.2 * 0.0 + 1.6 * 0.0 + 0.5 * 0.0 + 0 * 0.0 = 0.0 KN-m
Mux lateral bot = 0 * 0.0 + 0 * 0.0 = 0.0 KN-m
Mux gravity top = 1.2 * 0.0 + 1.6 * 0.0 + 0.5 * 0.0 + 0 * 0.0 = 0.0 KN-m
Mux lateral top = 0 * 0.0 + 0 * 0.0 = 0.0 KN-m
Muy gravity bot = 1.2 * 0.0 + 1.6 * 0.0 + 0.5 * 0.0 + 0 * 0.0 = 0.0 KN-m
Muy lateral bot = 0 * 0.0 + 0 * 0.0 = 0.0 KN-m
Muy gravity top = 1.2 * 0.0 + 1.6 * 0.0 + 0.5 * 0.0 + 0 * 0.0 = 0.0 KN-m
Muy lateral top = 0 * 0.0 + 0 * 0.0 = 0.0 KN-m
M1x grav = 0.0 KN-m M1x lat = 0.0 KN-m M2x grav = 0.0 KN-m M2x lat = 0.0 KN-m
M1x = 0.0 + 0.0 = 0.0 KN-m M2x = 0.0 + 0.0 = 0.0 KN-m (M2 is always positive)
M1y grav = 0.0 KN-m M1y lat = 0.0 KN-m M2y grav = 0.0 KN-m M2y lat = 0.0 KN-m
M1y = 0.0 + 0.0 = 0.0 KN-m M2y = 0.0 + 0.0 = 0.0 KN-m (M2 is always positive)
Mcx = 0.0 KN-m Mcy = 0.0 KN-m (not a biaxial column)
Factored moment Mu = √(0.0² + 0.0²) = 0.0 KN-m
Rotation angle Arc Tan (0.0 / 0.0) = 0° from X-axis

2 of 4
Your Company Name Project: Lighting Pole Foundation Design Page # ___
Engineer: Ahmed Khalifa 30-Jun-21
Descrip: Lighting Pole Foundation Design
ASDIP Concrete 4.4.8 CONCRETE COLUMN DESIGN www.asdipsoft.com

- Check the bending capacity for Pu = 1.4 KN and Mu = 0.0 KN-m


By trial and error, neutral axis depth 0.16
Strain1 = (0.16 * 53.2 - 6.8) / (0.16 * 53.2) * 0.0030 = 0.0007

As d Strain fs fc Fs = As(fs-fc) Ms = Fs(h/2-d) Is = As(h/2-d)²


(cm²) (cm) (KN/cm²) (KN/cm²) (KN) (KN-m) (cm⁴)
As1 = 2.01 6.8 0.0007 13.2 1.6 23.4 5.4 1083.3
As2 = 2.01 6.8 0.0007 13.2 2.5 23.4 5.4 1083.3
As3 = 2.01 6.8 0.0007 13.2 2.5 23.4 5.4 1083.3
As4 = 2.01 6.8 0.0007 13.2 2.6 23.4 5.4 1083.3
As5 = 2.01 6.8 0.0007 13.2 2.6 23.4 5.4 1083.3
As6 = 2.01 53.2 -0.0153 40.0 2.7 -80.5 18.7 1083.3
As7 = 2.01 53.2 -0.0153 40.0 2.7 -80.5 18.7 1083.3
As8 = 2.01 53.2 -0.0153 40.0 2.7 -80.5 18.7 1083.3
As9 = 2.01 53.2 -0.0153 40.0 2.6 -80.5 18.7 1083.3
As10 = 2.01 53.2 -0.0153 40.0 2.4 -80.5 18.7 1083.3
As11 = 2.01 45.5 -0.0126 40.0 2.2 -80.5 12.5 481.5
As12 = 2.01 37.7 -0.0100 40.0 1.9 -80.5 6.2 120.4
As13 = 2.01 30.0 -0.0073 40.0 1.5 -80.5 0.0 0.0
As14 = 2.01 22.3 -0.0047 40.0 1.1 -80.5 -6.2 120.4
As15 = 2.01 14.5 -0.0020 40.0 0.6 -80.5 -12.5 481.5
As16 = 2.01 45.5 -0.0126 40.0 0.0 -80.5 12.5 481.5
As17 = 2.01 37.7 -0.0100 40.0 0.0 -80.5 6.2 120.4
As18 = 2.01 30.0 -0.0073 40.0 0.0 -80.5 0.0 0.0
As19 = 2.01 22.3 -0.0047 40.0 0.0 -80.5 -6.2 120.4
As20 = 2.01 14.5 -0.0020 40.0 0.0 -80.5 -12.5 481.5
T = -1090.6 Ms = 120.6 Is = 13240.9
Conc. force Fc = 1092.1 KN
Conc. moment Mc = 288.2 KN-m
Nominal flexural strength Mn = 120.6 + 288.2 = 408.7 KN-m
ϕ-factor slope =
ϕ-factor slope = (0.65 - 0.90) / (0.65 * 4028.2 - 0.9 * 2056.6) = -0.0003 ACI 21.2.2
ϕ-factor =
ϕ-factor = Min (0.9, Max (0.65, -0.0003 * (1.4 - 0.9 * 2056.6) + 0.9)) = 0.90
Design flexural strength ϕMn = 0.90 * 408.7 = 367.9 KN-m ACI 21.2.2
Flexural ratio = 0.0 / 367.9 = 0.00 < 1.0 OK ACI 4.4.4

3 of 4
Your Company Name Project: Lighting Pole Foundation Design Page # ___
Engineer: Ahmed Khalifa 30-Jun-21
Descrip: Lighting Pole Foundation Design
ASDIP Concrete 4.4.8 CONCRETE COLUMN DESIGN www.asdipsoft.com

4 of 4

You might also like