Scribd
Upload
147 views7 pages

Red 47 Bom+Doc v1.2

This document provides a bill of materials (BOM) and assembly instructions for building a clone of the legendary RED47 tube microphone preamp. It warns that working with high voltages and soldering carries safety risks, and the creator assumes no responsibility for injuries. The BOM lists electronic components including resistors, capacitors, potentiometers, switches, tubes, transformers, and an enclosure needed to construct the preamp circuit. Difficulty is rated as medium.

Uploaded by

mrgreengenes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
147 views7 pages

Red 47 Bom+Doc v1.2

This document provides a bill of materials (BOM) and assembly instructions for building a clone of the legendary RED47 tube microphone preamp. It warns that working with high voltages and soldering carries safety risks, and the creator assumes no responsibility for injuries. The BOM lists electronic components including resistors, capacitors, potentiometers, switches, tubes, transformers, and an enclosure needed to construct the preamp circuit. Difficulty is rated as medium.

Uploaded by

mrgreengenes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

RED47

TUBE MIC PREAMP


BOM+DOC
this bord offer a possibility to make this legendary preamp

WARNING!

This modification is for technicians only. It subjects you to the health ans safety risks associated with chemical
solvents and soldering. You must use all normal safety precautions when working with these tools and materials.

General Audio Research and its principals are not responsible for any injury that may occur should you proceed
with this modification.

General Audio Research are indemnified from any damage to your audio equipement and any connected
electronic, you other property, and your person, that results from the operation of your equipment after you
have tampered with it.

! warning !

tube preamp use lethal High voltage.

Difficult level / MEDIUM

1
Caractéristiques :

• Vintage clone RED47 TUBE mic preamp

• 34,40, 46 dB gain

• Frequency 20hz-18khz

• EF86 & e88c tube

• Fine gain

• Switch 3 positions gain

Composant éléctronique

RESISTANCES:

(i recomand vintage carbon resistor for close original preamp)

• 100k

• 32k

2
• 150r

• 162r

• 6k81

• 124k

• 10k

• 47k5

• 200r

• 1M

• 1k quantity : 3

• 100k 2watt

• 392k 2watt

• 51k 2watt

• 332k 2watt

• 1M6 2watt

• 8k25 8 watt minimum !!

this heating resistor must leave a space between the pcb and the resistor

CONDENSATEUR :

• 0.1uf /400V mkp

• 0.022uf /400v mkp

• 0.47uf /400v mkp

• 1uf /400v mkp

3
• 20pf ceramic

• 220pf ceramic / styroflex / mica

• 100pf ceramic / styroflex / mica

• 47uf /25v électrolytique quantity :2

• 10uf /400v électrolytique quantity : 2

POTENTIOMETRE

• 1k LOG ( i change the value for 1k log ) fine gain is completely useless, 2 db variation ! ! but close to original
schematic !!

SWITCH

• 1 shorting MBB (move befor break ) we need 3 input and 1 output type lorlin switch

• input switch = 1 ,2 ,3

• output switch = A

Connecteur (optional)

• molex 2 pin screw x2

• molex 3 pin screw x2

• molex 3 pin screw x1

Tube socket

• noval socket x2

TUBE AUDIO

4
• ef86

• e88cc

FOR BUILD THIS PREAMP

YOU NEED

Transformer HT + filament (exemple)

Transformateur 1x200V + 1x6.3V

REGULATED POWER SUPPLY pcb

• 280 VDC HT B+

• 6.3 VDC filament tube

Transformateur audio( for mic preamp )

Input mic : primaire 150, 200 or 600 ohm / secondaire 15k or 20k or 50k 1:10 ratio

Output ligne : primaire 10k / secondaire 600 ohm or ratio 10:1 ratio

i recommande sowter UK , jensen , vigortronix for low budget

INPUT :

SOWTER TYPE 9970

Jensen JT-115K-E

vigortronix VTX-102-003. 600/25K

OUTPUT :

SOWTER TYPE 9980

JT-10K61-1M

5
VTX-101-003 25K/600

Enclosure

• Rack 2u

• xlr in & out

• knob quantity : 2

• switch on off

• IEC power

6
We strongly recommend the use of a commercial flux remover to clean the circuit board. 99% Isopropyl could
also work, or a commercial contact cleaner .

OK ITS DONE

You might also like