Department of Electrical Engineering

Faculty Member:_________________ Dated: ________________

Semester:_________________________ Section: ________________

_

EE-211: Electrical Network Analysis

Lab 2: Introduction to Digital Oscilloscope, Function
Generator Operation and PSpice
PLO4/CLO4 PLO5/CL PLO8/CLO6 PLO9/CLO
O5 7
Name Reg. No Viva /Quiz / Analysis Modern Ethics and Safety Individual and
Lab of data in Tool Usage Team Work
Performance Lab 5 marks
Report 5 marks 5 marks
5 marks
5 marks

EE-111: Linear Circuit Analysis Page 1

Objective
To become familiar with the operation and use of the digital
osciloscope and function generator .

EQUIPMENT REQUIRED
Instruments :
1)Digital Oscilloscope
2)Digital multimeter
3)Test Probe
4)Function generator
5)Resistors for potential divider circuit
6)Breadboard

RESUME OF THEORY
The oscilloscope is most important available to the practicing technican
or engineer. It permits the visual display of a signal that can reveal a range of
information regarding the operating characteristics of a circuit or system that
is not available with a standard multimeter. At first glance the instrument may
appear complex and difficult to master. Be assured, however, that once the
function of each section of the oscilloscope is explained and understood and
the system is used throughout a set of experiments, your expertise with this
important tool will develop quite rapidly.
In addition to the disply of a signal, it can be used to measure the
average value, rms value, frequency and period of a sinusoidal or non-
sinsousodial signal. The screen is divided in to centimeter division in the
vertical and horizontal directions . The verticical sensitivity is provided (or
set) volts /cm, whie the horzontal scale is provided(or set) in t time (s/cm).If a
particular signal occupies 6 vertical centimeters and the vertical sensitivity is
5mV/cm, the magnitude of the signal can be determined from the following
equation:
EE-111: Linear Circuit Analysis Page 2
 Signal voltage (un known) = vloltage ensitivity(V/cm)Xdeflection(cm)
VS=(5mV/cm) (6cm)= 30mV (1.1)

If one cycle of the same signal occupies 8cm on the horizontal scale
with a horizontal sensitity of 5µ/cm, the period and freqency of the signal can
be determinedusing the following equations:
T=(5µ/cm) (8cm)=40µs
And f -1/T = 1/40=25kHz (1.2)
An oscilloscope (commonly abbreviated to scope or O-scope) is a type
of electronic test instrument that allows signal voltages to be viewed, usually
as a two-dimensional graph of electrical voltage potentials (vertical axis)
plotted as a function of time (Horizontal axis). In addition one can plot a
voltage potential (vertical axis) against another voltage (horizontal axis).
Although an oscilloscope displays voltage on its vertical axis, any other
quantity that can be converted to a voltage can be displayed as well. The
oscilloscope is one of the most versatile and widely-used electronic
instruments. Oscilloscopes are widely used when it is desired to:
1. Observe the exact wave shape of an electrical signal.
2. Measure the amplitude of the signal
3. Measure the frequency
4. Observe distortion
5. Show the time between two events (such as pulse width or pulse rise time),
and show the relative timing of two related signals.
Calibration: Calibration is often regarded as including the process of adjusting
the output or indication on a measurement instrument to agree with value of the
applied standard, within a specified accuracy.

Steps:
1) Align the slot in the probe connector with the button on the CH 1 BNC.
2) Push to connect, and twist to the right to lock the probe in place.
3) Attach the probe tip and ground lead to the PROBE COMP connector.

EE-111: Linear Circuit Analysis Page 3

 FIGURE.1

4) Press auto button and the oscilloscope will set itself according to the
applied signal. You can press the Run/Stop button to stop the waveform at
any instant.
This device is also USB compatible. So you can store screenshots of waveforms
by plugging in a flash drive and pressing the storage button. (Store it in
bitmap format).
Oscilloscope Probe:
EE-111: Linear Circuit Analysis Page 4
 A test probe is a device used to connect electronic test equipment to
the device under test.
It has a High Input resistance. (About a Mega ohm)

Probe has a knob for attenutation of input signal. Make sure it is at 1x.

Function generator:
The function generator is an electronic instrument that can be
used a voltage supply time varying voltage waveforms like, Sinusoidal,
triangular and square-waves. Most electrical signals and forcing functions are
either of these functions or combinations of these basic types. Therefore, for
the study and analysis of the circuit parameters like time response, frequency
response the function generator acts as a required forcing function for the
circuit under study.
The function generator is shown in figure 2; and some of its control
knobs ad switches are shown in figures 2-2.

The
output
Amplitude from the
EE-111: Linear Circuit Analysiscontrol function
Page 5
knob generator
shall be
taken
from here
 FIGURE.2

Set up:
Tasks:
a. Turn ON the oscilloscope and adjust the various controls to see their
effects on the display.

b. Connect the function generator to the CH1 of the digital oscilloscope

and set the output of the generator to a 100 Hz sinusoidal waveform as shown
in figure 2.1.
We can select input wave shape and also see the adjusting frequency on the
screen shown in fig-2.1. Adjustment can be made as fig 2.2.

The WAVE switch

cycles between the
different
waveforms, square,
sinusoidal, and
FIGURE.2.1 triangular

EE-111: Linear Circuit Analysis Page 6

 FIGURE.2.2 Frequency
control knob to
fine tune
frequency

Figure.3
Horizontal Sensitivity

Figure.3 shows the HORIZONTAL controls: MENU knob, POSITION and

SCALE knobs of horizontal system. Following the exercise to familiarize with
the Buttons, knobs, and status bar.

c. Determine the period of the100Hz sinusoidal waveform by adjusting

the waveform on oscilloscope.
EE-111: Linear Circuit Analysis Page 7
 T=-----------------------------

d. Set horizontal sensitivity of the oscilloscope to 2ms/cm by rotating

the SCALE knob of the digital oscilloscope. Using the results of part c calculate
the number of divisions required to properly displaying one full cycle of the
100Hz signal.

Calculate Number of divisions=-----------

The horizontal POSITION knob moves displayed signal horizontally on

waveform window.
Q: Using the oscilloscope measure the number required divisions and insert
below. How does the result compare the calculated number of divisions?
Ans:________________________________________________________________________________________
______________________________________________________________________________________

e. Change the horizontal sensitivity of the oscilloscope to 5ms/cm by

rotating SCALE knob without touching any of the function generators. Using
the results of part d how many horizontal divisions will now be required to
display one full cycle of the 100Hz signal.

(Calculate)Number of divisions=-----------------------------
Q: Using the oscilloscope measure the number required divisions and insert
below. How does the result compare the calculated number of divisions?
Ans:________________________________________________________________________________________
______________________________________________________________________________________

f. Change the horizontal sensitivity of the oscilloscope to 1ms/cm by

rotating SCALE knob without touching any of the controls of the function
generator. Using the results of part d, how many horizontal divisions will now
be required to display one full cycle of the 100Hzsignal?

(Calculate)Number of divisions=----------------------

Q: Using the oscilloscope measure the number required divisions and insert
EE-111: Linear Circuit Analysis Page 8
below. How does the result compare the calculated number of divisions?
Ans:________________________________________________________________________________________
______________________________________________________________________________________

Q: What was the effect on the appearance of the sinusoidal waveform as

horizontal sensitivity was horizontal sensitivity was changed from 1ms/cm to
5ms/cm?
Ans:________________________________________________________________________________________
______________________________________________________________________________________

Q: Did the frequency of the signal on the screen change with the each horizontal
sensitivity? What conclusion can draw from the results?
Ans:________________________________________________________________________________________
______________________________________________________________________________________
g. Determine the frequency of the waveform.
Ans:________________________________________________________________________________________
______________________________________________________________________________________

Figure .4

Vertical Sensitivity

Figure.4 shows the VERTICAL controls, CH1, CH2, MATH, REF, and OFF buttons
and vertical POSITION, SCALE knobs. Following the exercise of the buttons,
knobs, and the status bar to be familiar with the vertical parameters settings.

EE-111: Linear Circuit Analysis Page 9

 h. Set the vertical sensitivity of the scope to1V/cm by rotating the
SCALE knob and adjust the amplitude control of the function generator to
establish, 4 V peak to peak (p-p), sinusoidal waveform on the screen.

i. Do not touch the control of the control of function generator but

return the sensitivity of the scope to 1v/cm and change the vertical sensitivity
to 2V/cm by rotating the SCALE knob. Using the sensitivity calculate the peak-
to-peak value of the sinusoidal waveform on the screen by first counting the
number if the vertical division between peak values and multiplying by the
sensitivity.

(Calculate) peak-to peak value=-----------------------------

j. Change the vertical sensitivity of the oscilloscope to0.5V/cm by

rotating the SCALE knob and repeat Part (j).

(Calculate) peak-to peak value=-----------------------------

Q: Did the peak-to peak value of the sinusoidal waveform change with the
change in vertical sensitivity? What conclusion can you draw from the results?
Ans:________________________________________________________________________________________
______________________________________________________________________________________

Q: What was the effect on the appearance of sinusoidal waveform as the vertical
sensitivity was changed from 2V/cm to 0.5V/cm?

Ans:________________________________________________________________________________________
______________________________________________________________________________________

Q: Did the peak-to peak amplitude of the signal change with the each vertical
sensitivity? What conclusion can you draw from the results?
Ans:________________________________________________________________________________________
______________________________________________________________________________________

Exercises
EE-111: Linear Circuit Analysis Page 10
 a. Make all the necessary adjustments to clearly display a 5000=Hz
6Vp-p sinusoidal signal on the oscilloscope. Establish the zero volt line at the
center of the screen.

Vertical sensitivity =--------------------------------

Horizontal sensitivity =--------------------------------

(Calculate)T=---------------------------------------

Store the waveform.

b. Calculate the period of the waveform using the number of required
horizontal divisions for a full cycle.

(Calculate)T=----------------------------------------------------
Include your labeled waveform in the lab report.

c. Repeat part(a) for a 200-Hz 1.8Vp-p square waveform.

Vertical sensitivity =--------------------------------

Horizontal sensitivity =-----------------------------

(Calculate)T=---------------------------------------

d. Repeat Part (a) for a 100-kHz p-p triangular wave.

Vertical sensitivity =--------------------------------

Horizontal sensitivity =-----------------------------

(Calculate)T=---------------------------------------

RMS Value
a. Reestablish the 1 KHz 4Vp-p sinusoidal waveform on the screen
calculate the effective value of the sinusoidal waveform.
EE-111: Linear Circuit Analysis Page 11
 (Calculate) V (rms) =-----------------------------------

b. Disconnect the function generator from the scope and measure the
effective (rms0 value of the output of the function generator using the digital
meter.
(DMM) V (rms ) =-----------------------------------

c. Determine the percent difference between the calculate and

measured values using the following equation:

% Difference=-----------------------------------------------------

d. Disconnect the function generator from the DMM and measure the
rms value of the output of the function generator using the scope.

Q: What was the difference in DMM and Scope values?

Ans:________________________________________________________________________________________
______________________________________________________________________________________

Using Both Input Channels Simultaneously

Set the Function generator to get a waveform corresponding to the
equation
V1=5 sin (2000t) V
Now make a potential divider circuit to get another waveform V2.
Show both the Waveforms Simultaneously by using both channel 1 and 2.

Problems:
Give V=5sin (2000t) +2, Determine the following parameters using
scope…

EE-111: Linear Circuit Analysis Page 12

 a. f=
b. ω=
c. T=
d. Peak value=
e. Peak-to-peak value=
f. Average Value=
g. Effective value(rms)=
h. DC level=

Show the waveform in your report.

Given Square wave of amplitude 8 and frequency 4000Hz, determine

the following parameters using scope…

a. f=
b. ω=
c. T=
d. Peak value=
e. Peak-to-peak value=
f. Effective value=
g. Average Value=
h. Rise time
i. Fall Time
j. DC level=
1. Given V rms=1.2V, and a frequency of 400Hz, determine the mathematical
expression for the sinusoidal voltage as a function of time and Generate this
function in Generator and view it in scope.

EE-111: Linear Circuit Analysis Page 13