TriBoard TC3X7

TriBoard Manual TC3X7

Hardware: TriBoard TC3X7 TH V2.0( 1) and TriBoard TC3X7 V2.0

About this document

Scope and purpose
The User Manual provide information about using, configuration and connecting the TriBoard with Infineon
AURIX™ TC3X7 device. The manual provide information for different hardware types. There exist different
hardware with Through Hole socket (TriBoard TC3X7 TH) and soldered devices (TriBoard TC3X7). The schematic
is identically for the all boards if not other mentioned in chapter schematic. The placing on the boards is slightly
different around the TC3X7 itself dependent of the space (socket need more space and has through hole), but the
most components are on the same location. All figures are valid for each board if not differently mentioned.

Intended audience
Design, verfication, test and software engineers will use this document to get an understanding of the
functionality and connections of the TriBoard.

User Manual Please read the Important Notice and Warnings at the end of this document V2.3
www.infineon.com TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Table of Contents

Table of Contents

About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-1

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TOC-2
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.3 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
3 TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Soldered board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Socketed board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2.1 Usable devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.2.2 Restricted usable devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.3.1 Failsafe handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.4 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.5 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.6 USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.6.1 Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.6.2 miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.7 FlexRay™ (E-RAY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.8 Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.9 MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.10 LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.11 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.12 HSCT (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.12.1 High speed with HSCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.13 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.14 Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.15 Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.16 Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.17 Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.17.1 OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.17.2 DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.17.3 DAPE (only Emulation Device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.17.4 DAP_SCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
3.17.5 High speed with DAP/DAPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
3.17.6 AGBT (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
3.17.7 ETK connector (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
3.17.8 EmW Power (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
4 TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 HW Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.1 Default Pad State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.2 Bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2.1 General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2.2 Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

User Manual TOC-2 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Table of Contents

5 Signal (on board used) Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.1 Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.3 Config Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.4 Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.5 Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.6 Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
6 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 On Board only used signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 TC397/TC387/TC377/TC3E7 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.3 TC367 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
6.4 TC337/TC327 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.5 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.6 USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.7 FlexRay™ (ERAY) connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.8 CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.9 LIN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
6.10 HSCT connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
6.11 Ethernet connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
6.12 OCDS1 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.13 DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.14 ETK connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.15 Ethernet miniWiggler power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.16 AGBT connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
7 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1 Known problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1.1 Known problems on TriBoard TC3X7 TH V2.0(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1.2 Known problems on TriBoard TC3X7 V2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.2 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.3 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
7.4 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11

User Manual TOC-3 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Introduction

1 Introduction
We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quick
access to the capabilities of TriCore's powerful architecture.
Applications can be developed easily. The Evaluation Board is equipped with a variety of memories and
peripherals for connection to the environment. There is also an interface for the On Chip Debugging Features
(OCDS1 and DAP).
The Evaluation Board allows easily the development of TriCore applications with the corresponding tools.
Subsequently, the applications can be downloaded and can be tested with the powerful debugger software.
This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through the
initial configuration of the TriBoard.
For detailed technical information about the TC3X7 (e.g. TC397, TC387, TC377, TC367, TC337, TC327, TC3E7)
please refer to the User Manual of the used device.

User Manual 1-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Features

2 Features

2.1 Summary of Features

– Infineon’s TC3X7 (TC397, TC387, TC377, TC367, TC337, TC327, TC3E7)1) AURIX™ 2G Controller in LFBGA-292
Package
– FlexRay™ 2) Transceivers
– High Speed CAN Transceivers (CAN-FD capable)
– USB to UART bridge
– Ethernet Gigabit PHY
– Serial Eeprom
– LIN Transceiver
– Crystal 20MHz (default) or External Clock
– USB miniWiggler JDS for easy debugging
– 8 Low Power Status LEDs
– 8-DIP switches for configuration
– access to all pins of controller
– 100mm x 160mm (EURO-Board)

Connectors
The TC3X7 TriBoard offers a wide variety of connectors:
– Standard power connector
– Micro USB connector for ASC Interface (ASC0) and miniWiggler
– RJ45 connector for Ethernet
– 16-pin header for JTAG interface (OCDS)
– 3 x 10-pin header for DAP, DAPE and DAP_SCR (DAPE only usable on Emulation Device)
– 10pin (2x5) Header for LIN Transceiver (LIN)
– 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)
– 2 x 10pin (2x5) Header for FlexRay™ (ERAY-A and ERAY-B)
– four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals
– optional ETK connector
– optional 2 x 6pin (IEEE1394) Socket for HSCT
– optional Aurora connector (only with Emulation Device)

Components
– Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV
– Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,25 Volt)
– LED indicating safe state signal 2 from TLF35584
– LED indicating /HDRST (ESR0) active state
– LED indicating activ miniWiggler JDS
– LED switched via DAS software
– 2 x Infineon’s FlexRay™ Transceiver TLE9221SX
– 2 x Infineon’s High Speed CAN-Transceiver TLE9251VSJ
– Infineon’s LIN-Transceiver TLE 7259-3GE
– USB to UART bridge FT2232HL (FTDI)

1) Please see Chapter 3.2.1 for usable and Chapter 3.2.2 for restrict usable devices in the socketed board.
2) FlexRay™ is a trademark of FlexRay Consortium.

User Manual 2-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Features

– Integrated 10/100/1000M Ethernet Precision Transceiver RTL8211FI-CG (Realtek)

– 8 general purpose LEDs
– 2K I2C Serial Eeprom with EUI-48™ 1) Node Identity (MICROCHIP)
– Reset switch
– Enable switch
– Generic switch
– 4-pin Dip switch

Zero Ohm Bridges

Zero Ohm resistors give the flexibility to configure the systems functionality.

1) EUI-48™ is trademarked by IEEE

User Manual 2-2 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Features

2.2 Block Diagram

XTAL

PLL
CAN0 TxCAN0 RJ45
RGMII Twisted Pair
RxCAN 0 PHY

CAN1
Transceiver
TxCAN1
TC3X7
RxCAN1 (e.g.
TC397,

optional
HSCT0 - TX/RX

HSCT0
OCDS1
TC387,

optional
HSCT1
HSCT1 - TX/RX
TC377,
Micro
USB USB
miniWiggler
TX0

RX0 TC367,
TX1 TC337,
TC327,
LIN

LIN
Transceiver
RX1

TC3E7)
TriCore
ERAY A

FlexRay™
Transceiver
CPU
ERAY B

WAKEUP
I²C

ENA
8 LED’s Multi Voltage Safety Micro
(P33.4 up to P33.7, Serial EEPROM Processor Supply
P20.11 up to P20.14) with EUI-48™ QSPI2 TLF35584QV

Figure 2-1 TriBoard Block Schematic

User Manual 2-3 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Features

2.3 Placement

X306

X604 X601

X 202

S202
Y 301

Y 401

D302 D303 D304 D305 D306 D307 D308 D309

U3 07
BU40 1

X403
X201
U401

X404

S 201

INFINEON TECHNOLOGIES AG
D401 D402

TriBoard-TC3X7 (TH) V2.0(1)

T301
X30 1
X 30 3

X402

U201
X4 01

Y 201
T 302
X30 2
X30 4

D504 D507
S5 01

U502

D506

C303 X 502
L502

D508 D505
X3 05

C502
X40 6

U501

S 502
L 501

R5 01
X50 1

X 603 X602
C501

Figure 2-2 TriBoard TC3X7 (TH) V2.0(1) Placement

User Manual 2-4 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3 TriBoard Information

3.1 Soldered board

TriBoard TC3X7 V2.0 is the soldered board and will be available only with usable devices and valid assembly
option. There is nothing to change. Please see also chapter Usable devices.

3.2 Socketed board

TriBoard TC3X7 TH V2.0(1) is the socketed board and will be available in two assembly options:
– For device with PMSLE module and without PMS module (TC337 and TC327 except TC337DA, TC337DT,
TC337DH and TC337DZ)
– For device with PMS module and without PMSLE module (all other devices)
Difference between this two module is, that the PMSLE use a Switch Capacitor Regulator for the core voltage
generation which need only an external capacitor (see schematic C518, no external coil, no external p+n mosfet).
The PMS module use a Step-down Regulator which need an external p+n mosfet (see schematic Q506) and an
external coil (see schematic L503).
If you get the board with TC337 or TC327 and you will use the board with any other device then you must make
sure that Q506 and L503 will be assembled otherwise the other devices will not work.
If you get the board with any other device than TC337 or TC327 and you will use the board with TC337 or TC327
then you must remove Q506 and L503. Please note that after this change the board will work only with TC337 and
TC327 until you reassemble Q506 and L503.
Mosfet Q506, coil L503 and capacitor C518 are red marked in the following Figure 3-1:

C316
C315
C314

C317

X701 X704 R389

R38 5

C308
R384

C30 7

C305 CB315

R3 88
R260 R258
R378

R3105 CB312 C312

R3110

C319
R310

CB4 12

C313
R311 1

CB413

C404
CB316
C406
CB314 C405
R370
R310 6

CB409
R257
R259

R3 107

R372
CB313
CB4 04

C4 01

R414 R404
RN301 CB311 L402
C4 03
R5 25

R419
R21 9

R440 CB411
R211

R371
CB41 0

R418 R442 U405

CB40 3

Q403
R381 R420
CB209
R416
R441
R21 8

R433 R422 R437 R417 Q402 R405

R231

R406

R254 R250 R252 R449

R237

R235

R233

R443
L20 1

R421

R448
R4 13

R410

R438 U402
R253 R251 U403
R447
R450

R436 Q401
CB406
R41 2

R307
CB208
CB407
R3 08

R3 09
R304

R407
R373 R415
R4 31

R409 R445
R374
R524

R302
C5 19

R328
RN302

CB30 1

R334
R303

U301

R305

R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333
R408

CB305
U303

R306 R321
R522 CB303
R338

R326
R322 R332
CB51 7

CB515

R317 R325 R331

R216

R215

R31 9
R214

R318

R343
CB5 18

CB2 06
R2 09

R314
CB516

C207 R340
R312
R350

Q502 CB307
R31 5

CB510 C208
CB302
R208

CB513

C206 R341
R353
U302

U30 4

R313 CB308
CB205 R342
C2 05

C2 04

C515

R311 CB306
R358
R3 16

R520 CB204 R533 R351

C407

R521 C408 R536 R352

Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
R238
C518
C520
Q504

R535
R239
C203 R511 C304
U306
C51 1
CB5 06

C510

C512

U503 Q506
R504

R220
R534

D501
R3 60

C506
C521 CB310
R222

R223

R245
R50 2

R503
L503 D503

R505 Q501
R5 06

R221
Q505

R246

X702 X703
D5 02

Figure 3-1 Location of PMS/PMSLE components on bottom side

User Manual 3-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3.2.1 Usable devices

Note: Note: Please check always the latest manual for complete list of usable/tested devices.

The board can be used with the following devices:

• TC397 B-Step (except TC397XA, TC397XT and TC397QA)
• TC387
• TC377 (except TC377TX)
• TC367
• TC337 (except TC337DA, TC337DT, TC337DH and TC337DZ, planned, not yet tested)
• TC327 (planned, not yet tested)
• TC3E7 (planned, not yet tested)

3.2.2 Restricted usable devices

• TC397 A-Step (except TC397XR and TC397XA)
– Ethernet will not work because device don’t support RGMII

• TC397 A-Step (only TC397XR and TC397XA)

• TC397 B-Step (only TC397XA, TC397XT and TC397QA)
• TC357
• TC3A7
• TC337 (only TC337DA, TC337DT, TC337DH and TC337DZ, planned, not yet tested)
– Ethernet will not work
– Select bootmode via DIP switch will not work
– different pinning therefore following signals are different connected

Board signal name TC397 (ADAS) signal TC357/TC3A7 signal TC337 signal name
name name
P00.0 P50.9 P50.9 P50.9
P00.1 P50.8 P50.8 P50.8
P00.2 P50.11 P50.11 P50.11
P00.3 P50.10 P50.10 P50.10
P00.4 P02.0 P02.0 P02.0
P00.5 P02.1 P02.1 P02.1
P00.6 P10.8 P10.8 P10.8
P00.7 P02.2 P02.2 P02.2
P00.8 P02.4 P02.4 P02.4
P00.9 P02.3 P02.3 P02.3
P00.10 P02.5 P02.5 P02.5
P00.11 P02.6 P02.6 P02.6
P00.12 P00.0 P00.0 P00.0
P01.3 P10.4 P10.4 P10.4
P01.4 P10.3 P10.3 P10.3
P01.5 P10.6 P10.6 P10.6

User Manual 3-2 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

Board signal name TC397 (ADAS) signal TC357/TC3A7 signal TC337 signal name
name name
P01.6 P10.5 P10.5 P10.5
P01.7 P10.7 P10.7 P10.7
P02.0 NC NC NC
P02.1 P50.0 P50.0 P50.0
P02.2 P50.1 P50.1 P50.1
P02.3 P50.2 P50.2 P50.2
P02.4 P50.3 P50.3 P50.3
P02.5 P50.4 P50.4 P50.4
P02.6 P50.5 P50.5 P50.5
P02.7 P50.6 P50.6 P50.6
P02.8 P50.7 P50.7 P50.7
P02.9 P10.0 P10.0 P10.0
P02.10 P10.2 P10.2 P10.2
P02.11 P10.1 P10.1 P10.1
P10.0 P51.5 P51.5 NC
P10.1 P51.4 P51.4 NC
P10.2 P51.9 P51.9 NC
P10.3 P51.7 P51.7 NC
P10.4 P51.6 P51.6 NC
P10.5 P51.8 P51.8 NC
P10.6 P51.11 P51.11 NC
P10.7 NC NC NC
P10.8 P51.10 P51.10 NC
P11.2 P11.11 P11.11 P11.11
P11.3 P11.12 P11.12 P11.12
P11.9 P51.1 P51.1 NC
P11.10 P51.0 P51.0 NC
P11.11 P51.3 P51.3 NC
P11.12 P51.2 P51.2 NC
P13.0 P11.3 P11.3 P11.3
P13.1 P11.2 P11.2 P11.2
P13.2 P11.10 P11.10 P11.10
P13.3 P11.9 P11.9 P11.9
AN24 AN38 NC NC
AN25 AN36 NC NC
AN26 AN37 NC NC
AN27 AN39 NC NC
AN28 AN46 NC NC

User Manual 3-3 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

Board signal name TC397 (ADAS) signal TC357/TC3A7 signal TC337 signal name
name name
AN29 AN44 NC NC
AN30 AN24 NC NC
AN31 AN25 NC NC
AN32 AN47 NC NC
AN33 P00.11 P00.11 NC
AN34 AN45 AN45 NC
AN35 P00.12 P00.12 P00.12
AN36 P00.6 P00.6 P00.6
AN37 P00.9 P00.9 P00.9
AN38 P00.5 P00.5 P00.5
AN39 P00.10 P00.10 NC
AN40 P00.4 P00.4 P00.4
AN41 P00.3 P00.3 P00.3
AN42 P02.8 P02.8 P02.8
AN43 P02.7 P02.7 P02.7
AN44 P00.8 P00.8 P00.8
AN45 P00.7 P00.7 P00.7
AN46 P00.2 P00.2 P00.2
AN47 P00.1 P00.1 P00.1

• TC377TX
– different pinning therefore following signals are different connected

Board signal name TC377TX signal name

P22.0 P22.10
P22.1 P22.11
P22.10 P22.0
P22.11 P22.1
P23.0 P23.2
P23.2 P23.3
P23.3 P22.12
VEXT (ball V19) VFLEX2

User Manual 3-4 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3.3 Power Supply

All needed voltages are generated via Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV and via
the microcontroller itself (+1,25V).
The supply device is available as two different devices:
TLF35584QVVS1 -> +5V standby voltage, +5V TriCore supply (V_UC)
TLF35584QVVS2 -> +3,3V standby voltage, +3,3V TriCore supply (V_UC)
Dependent of the assembled device the board works with 5V or 3,3V IO.
The TLF35584QV provide the following voltages:
+3,3V or +5V for standby (connected to VEVRSB)
+3,3V or +5V for TriCore (connected to VEXT)
+5V communcation supply (used by CAN and FlexRay™ transceivers)
+5V voltage reference (connected to VDDM and VAREFx)
+3,3V via LDO directly from pre regulator (used by Ethernet PHY)
Applying a stable supply voltage causes the power on reset after a short period. The three LED's (V_UC, +3.3V,
+1V25) indicate the status of the on board generated voltages.
A manual power on reset is executed by pressing the reset button.
The Board has to be connected to a +3,5V to +40V DC power supply.
The power consumption is not specified yet but a supply with 12V and 500mA is recommended. The pinout for
the supply connector is shown in Figure 6-7. There can be used any standard power pack with a connector where
the positive line is surrounded by the ground line.

3.3.1 Failsafe handling

In case that the device don’t contains a program which disable or service the window watchdog and error pin
monitor of the TLF35584 then the TLF35584 is going to a FAILSAFE state where all supplies are switched off. This
state can be left via reconnect the power plug or via the ENA button (S502). In this case you must connect a
debugger which is able to disable the window watchdog and error pin monitor to reprogram the microcontroller.
In the default state of the board the switching to FAILSAFE state is switched off via resistor R508 (0R).
If you will use/evaluate all safety features of the TLF35584 remove assembled R508. Make sure that you have a
proper initialization of TLF35584 in your software.
Resistor R508 is red marked in the following Figure 3-2:

User Manual 3-5 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

X306

X604 X601
C3 06
R383

C310 X202
L301
R390 R399 S202
C311 C318 CB319
Y301

X404

R256
D30 2

D30 3

D30 4

D30 5

D30 6

D30 7

D30 8

D30 9
Y401 R382

C309
CB318
R392 R393 R394 R395 R396 R397 R398

R39 1
CB4 01

R3104
U3 07

R2 55
R402
R439
BU40 1

R3100 X403
R3109
R31 03

X201
C320

CB317 R3101
R403 U401 R386
R3102
R226
CB405

R3108

S201
R377
CB4 08
C402
L4 01

R380 R379 R225

Q301

R375

R240
U4 04

R376
CB416

CB418
R401

CB419

CB402 CB414
R453
U407 U408

R230

R232

R234

R236

R217
D401 D402 U406 R241
R45 5
T 301

CB417

R456
R4 46

X30 1

R411
X30 3

R335

R444
R336

R428

CB415

R429
R451

R427 R430
R454

U201
R33 7

C30 1

R213 X402
R423

R212 R452
R329
X4 01

R424

C202
R324
R202
R206

CB20 1
R205
T30 2

R201 R204

Y201
R20 7
R426

R425

C201
X30 2

CB202
X30 4

R53 1

R354
R532

R203
R355

R35 6

R344
R3 57

C302

S5 01

U502
C505
D504 D507
C50 4

C5 03

D506
C5 08
C5 09

R50 8
CB502

C303 X502

R34 6
L502

D508 D505

U3 05

CB309
R509 R247
X3 05

R348
R361
C502 R349

C522
D301
R359

X40 6

U501 R347
S502
R249

C507
CB5 01

R2 48

R507 R244
R457
L 501

R5 01
X50 1

X603 X602
C501

Figure 3-2 Resistors for TLF35584 Safety feature handling with switch on

3.4 LEDs
There are 15 LEDs on board:
– D302 up to D305 (blue) -> toogle LEDs connected to P33.4 ... P33.7
– D306 up to D309 (blue) -> toogle LEDs connected to P20.11 ... P20.14
– D504 RST (red) -> RESET LED indicate the reset state of the board (/ESR0)
– D505 +1V25 (green) -> +1V25 power supply indication
– D506 +3V3 (green) -> +3,3V power supply indication
– D507 V_UC (green) -> +5V/+3,3V power supply indication
– D508 SS2 (green) -> safe state signal 2 indication
– D402 ACT (green) -> on board miniWiggler JDS is ACTIV
– D401 RUN (blue) -> Debug RUN mode (switched by DAS Server)

3.5 Clock
On the board is a fixed crystal with 20MHz assembled. You can change this by replacing Y101 (soldered).

3.6 USB Connector

The USB connector is used for connection to a PC. Via the USB it is possible to power the board, using the ASCLIN0
as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 6-8.
NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. For
actual DAS software please contact your local FAE.
The software can also be found on:
DAS website
User Manual 3-6 V2.3
TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3.6.1 Serial Connection to PC

After the first connection of USB to a PC the needed driver will be installed automatically. During this there will
be created a new COM port on PC. This COM port can be used to communicate with the board via ASCLIN0 of the
device. Per default the ASCLIN0 is used on P14.0 and P14.1 (e.g. Generic Bootstrap Loader) . In case you will use
the Generic Bootstrap Loader via CAN or ASCLIN0 via P15.2 and P15.3 you must:
– remove R436 and R437 (this disconnect the serial connection from P14.0 and P14.1)
– remove R301 and R302 (this disconnect the CAN0 transceiver from P20.7 and P20.8)
– assemble R438 and R440 with 0R resistor (size 0603) to connect P15.2 and P15.3 to serial connection
– assemble R303 and R304 with 0R resistor (size 0603) to connect P14.0 and P14.1 to CAN0 transceiver

The mentioned resistors are red marked in Figure 3-3.

C316
C315
C314

C317

X701 X704 R389

R38 5
C308

R384

C30 7
C305 CB315

R3 88
R260 R258

R378
R3105 CB312 C312

R3110
C319

R310

CB4 12
C313

R311 1

CB413
C404
CB316
C406
CB314 C405
R370

R310 6
CB409
R257
R259

R3 107
R372
CB313

CB4 04

C4 01
R414 R404
RN301 CB311 L402

C4 03
R5 25

R419
R21 9

R440 CB411
R211

R371

CB41 0
Q403 R418 R442 U405

CB40 3
R381 R420
CB209
R416
R441
R21 8

R433 R422 R437 R417 Q402 R405

R231

R406
R254 R250 R252 R449
R237

R235

R233

R443
L20 1

R421
R448

R4 13

R410
R438 U402
R253 R251 U403
R447

R450
Q401
R436 CB406

R41 2
R307
CB208

CB407
R3 08

R3 09
R407
R304

R373 R415

R4 31
R409 R445
R374
R524

R302
C5 19

R328
RN302

CB30 1

R334
R303

U301

R305
R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333
R408
CB305

U303
R306 R321
R522 CB303

R338
R326
R322 R332
CB51 7

CB515

R317 R325 R331

R216

R215

R31 9
R214

R318

R343
CB5 18

CB2 06
R2 09

R314
CB516

C207 R340
R312

R350
Q502 CB307
R31 5

CB510 C208
CB302
R208

CB513

C206 R341
R313 R353
U302

U30 4
CB308
CB205 R342
C2 05

C2 04

C515

R311 CB306
R358
R3 16

R520 CB204 R533

R351
C407

R521 C408 R536 R352

Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
C518 R238

C520
Q504

R535
R239
C203 R511 C304
U306
C51 1
CB5 06

C510

C512

U503 Q506
R504

R220
R534

D501
R3 60

C506
C521 CB310
R222

R223

R245
R50 2

R503
L503 D503

R505 Q501
R5 06

R221
Q505

R246

X702 X703
D5 02

Figure 3-3 Resistors for ASC connection (ASC0)

3.6.2 miniWiggler JDS

The miniWiggler JDS is a low cost debug tool which allows you access to the JTAG of the device. Make sure that
you have the latest DAS release. Debugging is possible via the DAS Server ‘UDAS‘. Please contact your prefered
debug vendor for support of DAS.
If you have connected the board to the PC and there runs the DAS server, then a working connection is visible via
the green ACTIV LED.
The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client).
IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and X402 (DAP) if the
ACTIV LED is on.

User Manual 3-7 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

Per default the miniWiggler is connected to the DAP. It is possible to change the connection to DAPE (DAP of
emulation device if available). If resistors R214, R215 and R216 assembled (default) then the standard DAP is
connected to miniWiggler otherwise if R217, R218 and R219 are assembled the the DAPE of emulation device is
connected to miniWiggler. Please note that there should be connected only standard DAP or DAPE. If all this
resistors are not assembled then the miniWiggler can’t be used. In this case only the DAP connectors X402 and
X403 can be used. See Figure 3-8 and Figure 3-9.

3.7 FlexRay™ (E-RAY)

The board has 2 IDC10 plugs for FlexRay™ Communication (channel A and B) with up to 10 Mbit/s. For the pinout
of the plugs see Figure 6-9. You can use a IDC female connector with crimpconnector, flat cable and SUB-D 9 plug
with crimpconnector to have a 1:1 adapter to SUB-D 9.
The transceiver are connected to the TriCore device via zero ohm resistors (R325 up to R329 and R340 up to R344)
which must be removed to use the ports outside.
ERAY-A can be connected to P14.8, P14.9 and P14.10 (default, usable with ERAY0 and ERAY1) and to P02.0, P02.1
and P02.4 (only usable with ERAY0). Transceiver for channel A can be enabled/disabled via P32.3 (default) or via
P10.2. The error state of transceiver channel A can be read out via P32.2 (default) or via P10.1.
ERAY-B is connected to P14.5, P14.6 and P14.7 (default, usable with ERAY0 and ERAY1). Transceiver for channel A
can be enabled/disabled via P20.10 (default). The error state of transceiver channel A can be read out via P20.9
(default).
For more information look in the user manual for TC3X7.

Note: TC327 don’t support FlexRay™.

3.8 Serial Eeprom

Note: TC337 don’t have I2C module. Access to the eeprom only with simulation of I2C protocol via bit banging
possible.

The I2C via P15.4 and P15.5 of the TC3X7 is connected to a serial EEPROM with a size of 2KBit (2 x 128 x 8). The slave
address of this EEPROM is 0x50. The upper half of the array (80h-FFh) is permanently write-protected. Write
operations to this address range are inhibited. Read operations are not affected. This upper half contains a pre-
programmed EUI-48™ node address which can be used as MAC ID for Ethernet. The other 128 bytes are writable
by customer.
To disconnect (disable) the EEPROM remove resistor R348 and R349.

3.9 MultiCAN
On the board are two CAN transceiver connected to the CAN0 and CAN1 of TC3X7. The transceivers are connected
to two IDC10 plug. For the pinout of IDC10 plug see Figure 6-10. You can use a IDC female connector with
crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
The transceiver are connected to the TriCore device via zero ohm resistors (R301 up to R304 and R311 up to R314)
which must be removed to use the ports outside.
CAN0 can be used via P20.7 and P20.8 (node 0, default) or P14.0 and P14.1 (node 1). CAN1 can be used via P23.0
and P23.1 (node 0, default) or P00.0 and P00.1 (node 0).

Note: CAN1 on TC337 is only usable via P00.0 and P00.1 (P23.0 don’t exist).

User Manual 3-8 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3.10 LIN
On the board is one LIN transceiver connected to the ASCLIN1 on TC3X7 (P15.0 and P15.1). The transceiver are
connected to one IDC10 plug. For the pinout of IDC10 plug see Figure 6-11. You can use a IDC female connector
with crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
To disconnect the LIN remove resistor R364 and R365.
The LIN can be used in master and in slave mode. For the master mode there is per default a pull-up of 1K (R360)
and a capacitor of 1nF (C304) on the BUS assembled. For using the LIN in slave mode the pull-up resistor R360
must be removed and maybe the capacitor changed to a smaller value (e.g. 220pF).
The mentioned resistor and capacitor are red marked in Figure 3-4

C316
C315
C314

C317

X701 X704 R389

R38 5
C308

R384

C30 7
C305 CB315

R3 88
R260 R258

R378
R3105 CB312 C312

R3110
C319

R310

CB4 12
C313

R311 1

CB413
C404
CB316
C406
CB314 C405
R370

R310 6
CB409
R257
R259

R3 107
R372
CB313

CB4 04

C4 01
R414 R404
RN301 CB311 L402

C4 03
R5 25

R419
R21 9

R440 CB411
R211

R371

CB41 0
R418 R442 U405

CB40 3
Q403
R381 R420
CB209
R416
R441
R21 8

R433 R422 R437 R417 Q402 R405

R231

R406
R254 R250 R252 R449
R237

R235

R233

R443
L20 1

R421
R448

R4 13

R410
R438 U402
R253 R251 U403
R447

R450
R436 Q401
CB406

R41 2
R307
CB208

CB407
R3 08

R3 09
R304
R407
R373 R415

R4 31
R409 R445
R374
R524

R302
C5 19

R328
RN302

CB30 1

R334
R303

U301

R305
R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333

R408
CB305

U303
R306 R321
R522 CB303

R338
R326
R322 R332
CB51 7

CB515

R317 R325 R331

R216

R215

R31 9
R214

R318

R343
CB5 18

CB2 06
R2 09

R314
CB516

C207 R340
R312

R350
Q502 CB307
R31 5

CB510 C208
CB302
R208

CB513

C206 R341
R353
U302

U30 4
R313 CB308
CB205 R342
C2 05

C2 04

C515

R311 CB306
R358
R3 16

R520 CB204 R533 R351

C407

R521 C408 R536 R352

Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
R238
C518
C520
Q504

R535
R239
C203 R511 C304
U306
C51 1
CB5 06

C510

C512

U503 Q506
R504

R220
R534

D501
C506 R3 60
C521 CB310
R222

R223

R245
R50 2

R503
L503 D503

R505 Q501
R5 06

R221
Q505

R246

X702 X703
D5 02

Figure 3-4 Components for LIN Master Mode

3.11 Ethernet
The TriBoard provide a RJ45 connector (X306) for twisted pair ethernet connections.The TriBoard use a Realtek
Integrated 10/100/1000M Ethernet Precision Transceiver RTL8211FI-CG as physical interface device. For more
information about the ethernet modul see TC3X9 User’s Manual, about the PHY see the RTL8211F datasheet. For
the pinout of RJ45 see Figure 6-13.
The PHY is connected to the TriCore device via resistors and resistor arrays (R370 up to R374 and RN301 up to
RN302).
For the connection between TriCore and PHY is used RGMII.

Note: Please note that the used signals for RGMII (P11.0 up to P11.12) are not connected to any connector.

Note: TC327 and TC337 don’t support ethernet.

User Manual 3-9 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3.12 HSCT (optional)

The TriBoard provide a footprint of IEEE 1394 socket (X201 and X202) for connection to other TC3XX via HSCT.

Note: Don’t use X201 and X202 for connection to any IEEE 1394
device, this can destroy the board and/or the connected
device.
X201 is connected to HSCT0 and X202 to HSCT1 of the used device (if used microcontroller support second HSCT).
For connect two TriBoards you need to assemble this socket (Lumberg 2415 01) on each board and connect the
boards with a standard 6 pin IEEE 1394 cable. For the pinout of socket see Figure 6-12.

Note: TC327 and TC337 don’t support HSCT.

Note: HSCT1 only usable with TC397.

3.12.1 High speed with HSCT

For use the HSCT connection between two board you need to remove 9 resistors to have a very short connection
between device and connector. On the TC3X7 Triboard this 9 resistors are R250, R251, R252, R253, R254, R257,
R258, R259 and R260 (red marked in Figure 3-5). This resistors needs to be removed.
mportant: When the resistors are removed then the port signals P20.0, P21.2, P21.3, P21.4, P21.5, P21.0, P21.1,
P22.2 and P22.3 are no longer available on the 80 pin samtec connectors.

User Manual 3-10 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

C316
C315
C314

C317

X701 X704 R389

R38 5
C308

R384

C30 7
C305 CB315

R3 88
R260 R258

R378
R3105 CB312 C312

R3110
C319

R310

CB4 12
C313

R311 1

CB413
C404
CB316
C406
CB314 C405
R370

R310 6
CB409

R257
R259

R3 107
R372
CB313

CB4 04

C4 01
R414 R404
RN301 CB311 L402

C4 03
R5 25
R419

R21 9
R440 CB411

R211
R371

CB41 0
R418 R442 U405

CB40 3
Q403
R381 R420
CB209
R416
R441

R21 8
R433 R422 R437 R417 Q402 R405

R231

R406
R254 R250 R252 R449

R237

R235

R233
R443

L20 1

R421
R448

R4 13

R410
R438 U402
R253 R251 U403
R447

R450
R436 Q401
CB406

R41 2
R307
CB208

CB407
R3 08

R3 09
R304
R407
R373 R415

R4 31
R409 R445
R374

R524
R302

C5 19
R328

RN302

CB30 1

R334
R303

U301

R305
R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333

R408
CB305

U303
R306 R321
R522 CB303

R338
R326
R322 R332

CB51 7

CB515
R317 R325 R331
R216

R215

R31 9
R214

R318
R343

CB5 18

CB2 06
R2 09

R314

CB516
C207 R340
R312

R350
Q502 CB307

R31 5
CB510 C208

CB302
R208

CB513

C206 R341
R353

U302

U30 4
R313 CB308
CB205 R342

C2 05

C2 04

C515
R311 CB306
R358

R3 16
R520 CB204 R533 R351

C407
R521 C408 R536 R352
Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
R238
C518
C520

Q504
R535
R239
C203 R511 C304
U306

C51 1
CB5 06

C510

C512
U503 Q506

R504
R220

R534
D501

R3 60
C506
C521 CB310
R222

R223

R245

R50 2
R503
L503 D503

R505 Q501

R5 06
R221

Q505
R246

X702 X703

D5 02
Figure 3-5 Resistors for high speed HSCT

3.13 ADC
On this boards are 6 ADC channels prepared with a low pass filter. On pin AN7, AN20, AN21, AN31, AN44 and AN45
is assembled a capacitor of 47nF and a serial resistor of 4,7K. The filter components are red marked in the
following figures (Figure 3-6 and Figure 3-7).

User Manual 3-11 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

X306

X604 X601
C3 06
R383

C310 X202
L301
R390 R399 S202
C311 C318 CB319
Y301

X404

R256
D30 2

D30 3

D30 4

D30 5

D30 6

D30 7

D30 8

D30 9
Y401 R382

C309
CB318
R392 R393 R394 R395 R396 R397 R398

R39 1
CB4 01

R3104
U3 07

R2 55
R402
R439
BU40 1

R3100 X403
R3109
R31 03

X201
C320

CB317 R3101
R403 U401 R386
R3102
R226
CB405

R3108

S201
R377
CB4 08
C402
L4 01

R380 R379 R225

Q301

R375

R240
U4 04

R376
CB416

CB418
R401

CB419

CB402 CB414
R453
U407 U408

R230

R232

R234

R236

R217
D401 D402 U406 R241
R45 5
T 301

CB417

R456
R4 46

X30 1

R411
X30 3

R335

R444
R336

R428

CB415

R429
R451

R427 R430
R454

U201
R33 7

C30 1

R213 X402
R423

R212 R452
R329
X4 01

R424

C202
R324
R202
R206

CB20 1
R205
T30 2

R201 R204

Y201
R20 7
R426

R425

C201
X30 2

CB202
X30 4

R53 1

R354
R532

R203
R355

R35 6

R344
R3 57

C302

S5 01

U502
C505
D504 D507
C50 4

C5 03

D506
C5 08
C5 09

R50 8
CB502

C303 X502

R34 6
L502

D508 D505

U3 05

CB309
R509 R247
X3 05

R348
R361
C502 R349

C522
D301
R359

X40 6

U501 R347
S502
R249

C507
CB5 01

R2 48

R507 R244
R457
L 501

R5 01
X50 1

X603 X602
C501

Figure 3-6 Filter components of ADC channels on Top Side

C316
C315
C314

C317

X701 X704 R389

R38 5

C308
R384

C30 7

C305 CB315

R3 88
R260 R258
R378

R3105 CB312 C312

R3110

C319
R310

CB4 12

C313
R311 1

CB413

C404
CB316
C406
CB314 C405
R370
R310 6

CB409
R257
R259

R3 107

R372
CB313
CB4 04

C4 01

R414 R404
RN301 CB311 L402
C4 03
R5 25

R419
R21 9

R440 CB411
R211

R371
CB41 0

R418 R442 U405

CB40 3

Q403
R381 R420
CB209
R416
R441
R21 8

R433 R422 R437 R417 Q402 R405

R231

R406

R254 R250 R252 R449

R237

R235

R233

R443
L20 1

R421

R448
R4 13

R410

R438 U402
R253 R251 U403
R447
R450

R436 Q401
CB406
R41 2

R307
CB208
CB407
R3 08

R3 09
R304

R407
R373 R415
R4 31

R409 R445
R374
R524

R302
C5 19

R328
RN302

CB30 1

R334
R303

U301

R305

R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333
R408

CB305
U303

R306 R321
R522 CB303
R338

R326
R322 R332
CB51 7

CB515

R317 R325 R331

R216

R215

R31 9
R214

R318

R343
CB5 18

CB2 06
R2 09

R314
CB516

C207 R340
R312
R350

Q502 CB307
R31 5

CB510 C208
CB302
R208

CB513

C206 R341
R353
U302

U30 4

R313 CB308
CB205 R342
C2 05

C2 04

C515

R311 CB306
R358
R3 16

R520 CB204 R533 R351

C407

R521 C408 R536 R352

Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
R238
C518
C520
Q504

R535
R239
C203 R511 C304
U306
C51 1
CB5 06

C510

C512

U503 Q506
R504

R220
R534

D501
R3 60

C506
C521 CB310
R222

R223

R245
R50 2

R503
L503 D503

R505 Q501
R5 06

R221
Q505

R246

X702 X703
D5 02

Figure 3-7 Filter components of ADC channels on Bottom Side

User Manual 3-12 V2.3
TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3.14 Other peripherals

For all other peripherals there are no special plugs on the board. The peripheral signals are available on the
different connectors. See “Connector Pin Assignment” on Page 6-1.

3.15 Toggle LED’s

The status LED’s are low active and can be controlled by Software.
Port 20 pin 11 up to pin 14 are connected to single LED’s (D306... D309) and powered by the normal
microcontroller voltage.
Port 33 pin 4 up to pin 7 are connected to single LED’s (D302... D305) and powered by the standby voltage. This
means that this LED’s can be are activ also when the board is in standby mode and only the standby voltage
available (port 33 is powered by VEVRSB pin which is connected to standby supply of TLF35584). In this case the
port pins are controlled by the standby controller if available.

3.16 Buttons
On the board are three buttons.
The reset button (S501) will apply a warm power on reset to the device.
The ENA button (S502) will be used to enable/wakeup the TLF35584.
The P33.11 button (S202) can be used by software as input. Also can this button used by the standby controller
to react on an event when only standby supply is available (e.g. wakeup the TLF35584 via P33.10).

3.17 Debug System

3.17.1 OCDS1
The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of Microcontroller (+5V
default or +3,3V). For pinout of the connector see Figure 6-14. You can connect any debugger to this connector.
The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals in the connector then
assemble R424 and R425 or R426 with a 0R resistor.
If you connect a debug hardware make sure that the miniWiggler JDS (see “miniWiggler JDS” on Page 3-7) is not
activ (ACTIV LED is off) and on the DAP connector (X402) is no hardware connected or the hardware is tristated.
If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB connection to the PC.
In case that R217, R218 and R219 are assembled instead of R214, R215 and R216 then the connector can be used
only for DAP connection to DAPE. If R214 up to R219 not assembled then the connector is not usable.

3.17.2 DAP
The board comes with a DAP connector (X402). For pinout of this connector see Figure 6-15. You can connect a
DAP hardware here. If you use this connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off)
and a connected OCDS1 hardware is disconnected or tristated.

3.17.3 DAPE (only Emulation Device)

The board comes also with another DAP connector (X403) which is connected to DAPE in case that an emulation
device is used. For pinout of this connector see Figure 6-15. You can connect a DAP hardware here. If you use this
connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off) and a connected OCDS1 hardware is
disconnected or tristated in case that R217, R218 and R219 are assembled.

User Manual 3-13 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

3.17.4 DAP_SCR
Additional DAP connector (X406) is connected to DAP_SCR. This DAP can be used as private DAP connection to
the standby controller. For pinout of this connector see Figure 6-15. You can connect a DAP hardware here. This
DAP use P33.6 and P33.7 which are connected to LED on the board. Maybe it is necessary to remove R393 and
R394 if the speed of the connection is not fast enough.

3.17.5 High speed with DAP/DAPE

For use the DAP connection with 160 MHz you need to remove 3 resistors to have a very short connection between
device and connector. On the TC3X7 Triboard this 3 resistors are R214, R215 and R216 for DAP or R217, R218 and
R219 for DAPE (red marked in Figure 3-8 and Figure 3-9). This resistors needs to be removed.
Important: When the resistors are removed then only the DAP and DAPE connector on the board can be used. The
on board wiggler and the OCDS1 connector couldn’t be use (are disconnected) in this case, also the DAP/JTAG
part of AGBT connector and the ETK connector couldn’t be used.
All resistors are red marked in the following figures:

X306

X604 X601
C3 06
R383

C310 X202
L301
R390 R399 S202
C311 C318 CB319
Y301

X404
R256
D30 2

D30 3

D30 4

D30 5

D30 6

D30 7

D30 8

D30 9

Y401 R382

C309
CB318
R392 R393 R394 R395 R396 R397 R398
R39 1
CB4 01

R3104
U3 07

R2 55

R402
R439
BU40 1

R3100 X403
R3109

R31 03

X201
C320

CB317 R3101
R403 U401 R386
R3102
R226
CB405

R3108
S201

R377
CB4 08
C402
L4 01

R380 R379 R225

Q301

R375
R240
U4 04

R376
CB416

CB418
R401

CB419

CB402 CB414
R453
U407 U408
R230

R232

R234

R236

R217

D401 D402 U406 R241

R45 5
T 301

CB417

R456
R4 46

X30 1

R411
X30 3

R335

R444
R336

R428

CB415

R429
R451

R427 R430
R454

U201
R33 7

C30 1

R213 X402
R423

R212 R452
R329
X4 01

R424

C202
R324
R202
R206
CB20 1

R205
T30 2

R201 R204
Y201
R20 7
R426

R425

C201
X30 2

CB202
X30 4

R53 1

R354
R532

R203
R355

R35 6

R344
R3 57

C302

S5 01

U502
C505
D504 D507
C50 4

C5 03

D506
C5 08
C5 09

R50 8
CB502

C303 X502
R34 6
L502

D508 D505
U3 05

CB309

R509 R247
X3 05

R348

R361
C502 R349
C522
D301
R359

X40 6

U501 R347
S502
R249

C507
CB5 01

R2 48

R507 R244
R457
L 501

R5 01
X50 1

X603 X602
C501

Figure 3-8 Location of DAP resistors on Top Side

User Manual 3-14 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

C316
C315
C314

C317

X701 X704 R389

R38 5
C308

R384

C30 7
C305 CB315

R3 88
R260 R258

R378
R3105 CB312 C312

R3110
C319

R310

CB4 12
C313

R311 1

CB413
C404
CB316
C406
CB314 C405
R370

R310 6
CB409

R257
R259

R3 107
R372
CB313

CB4 04

C4 01
R414 R404
RN301 CB311 L402

C4 03
R5 25
R419

R21 9
R440 CB411

R211
R371

CB41 0
Q403 R418 R442 U405

CB40 3
R381 R420
CB209
R416
R437 R417 Q402 R441
R433 R422 R405

R218

R231

R406
R254 R250 R252 R449

R237

R235

R233
R443

L20 1

R421
R448

R4 13

R410
R438 U402
R253 R251 U403
R447

R450
Q401
R436 CB406

R41 2
R307
CB208

CB407
R3 08

R3 09
R407

R304
R373 R415

R4 31
R409 R445
R374

R524
R302

C5 19
R328

RN302

CB30 1

R334
R303

U301

R305
R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333

R408
CB305

U303
R306 R321
R522 CB303

R338
R326
R322 R332

CB51 7

CB515
R317 R325 R331
R216

R215

R31 9
R214

R318
R343

CB5 18

CB2 06
R2 09

R314

CB516
C207 R340
R312

R350
Q502 CB307

R31 5
CB510 C208

CB302
R208

CB513

C206 R341
R313 R353

U302

U30 4
CB308
CB205 R342

C2 05

C2 04

C515
R311 CB306
R358

R3 16
R520 CB204 R533
R351

C407
R521 C408 R536 R352
Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
C518 R238

C520

Q504
R535
R239
C203 R511 C304
U306

C51 1
CB5 06

C510

C512
U503 Q506

R504
R220

R534
D501

R3 60
C506
C521 CB310
R222

R223

R245

R50 2
R503
L503 D503

R505 Q501

R5 06
R221

Q505
R246

X702 X703

D5 02
Figure 3-9 Location of DAP resistors on Bottom Side

3.17.6 AGBT (optional)

The TriBoard provide a 22 pin high speed samtec connector (X405) for highest speed connection via AGBT. This
connector should be assembled by your self if needed.
The AGBT interface is only available on emulation devices.
For the pinout of connector see Figure 6-18.
The needed Samtec connector is: ASP-137969-01 (serie ERM8, Nexus HS22).

Note: The robustness of AGBT communication depends on the PCB high-speed design quality and the
physical connection of a microcontroller on the board. It is highly recommended to use boards with
properly soldered microcontrollers for the highest reliability of the AGBT in the full operating range.

3.17.7 ETK connector (optional)

The TriBoard provide a 10 pin samtec connector (X404) for connecting to an ETK. This connector should be
assembled by your self if needed.
For the pinout of connector see Figure 6-16.
The needed Samtec connector is: TFM-105-02-A.

3.17.8 EmW Power (optional)

The TriBoard provide the 4 pin power connector (X502) for the Ethernet miniWiggler (EmW). This connector
should be assembled by your self if needed.
For the pinout of connector see Figure 6-17.

User Manual 3-15 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Information

The needed Samtec connector is the JST B4B-PH-K.

The connector provide the input voltage to the Ethernet miniWiggler and an enable/wakeup signal connected to
TLF35584 and a standby voltage of +1,25V connected to VDDSB of device. In case the EmW is used you must
remove R522. If R522 is removed then you must make sure that the EmW is always connected. Otherwise with
assembled R522 (default) you should not connect the pin 4 of connector.
The mentioned resistor is red marked in Figure 3-10

C316
C315
C314

C317

X701 X704 R389

R38 5
C308

R384

C30 7
C305 CB315

R3 88
R260 R258

R378
R3105 CB312 C312

R3110
C319

R310

CB4 12
C313

R311 1

CB413
C404
CB316
C406
CB314 C405
R370

R310 6
CB409
R257
R259

R3 107
R372
CB313

CB4 04

C4 01
R414 R404
RN301 CB311 L402

C4 03
R5 25
R419
R21 9

R440 CB411

R211
R371

CB41 0
R418 R442 U405

CB40 3
Q403
R381 R420
CB209
R416
R441
R21 8

R433 R422 R437 R417 Q402 R405

R231

R406
R254 R250 R252 R449

R237

R235

R233
R443
L20 1

R421
R448

R4 13

R410
R438 U402
R253 R251 U403
R447

R450
R436 Q401
CB406

R41 2
R307
CB208

CB407
R3 08

R3 09
R304
R407
R373 R415

R4 31
R409 R445
R374
R524

R302
C5 19

R328
RN302

CB30 1

R334
R303

U301

R305
R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333

R408
CB305

U303
R306 R321
R522 CB303

R338
R326
R322 R332
CB51 7

CB515

R317 R325 R331

R216

R215

R31 9
R214

R318
R343
CB5 18

CB2 06
R2 09

R314
CB516

C207 R340
R312

R350
Q502 CB307

R31 5
CB510 C208
CB302
R208

CB513

C206 R341
R353

U302

U30 4
R313 CB308
CB205 R342
C2 05

C2 04

C515
R311 CB306
R358

R3 16
R520 CB204 R533 R351
C407

R521 C408 R536 R352

Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
R238
C518
C520
Q504

R535
R239
C203 R511 C304
U306

C51 1
CB5 06

C510

C512
U503 Q506
R504

R220
R534

D501

R3 60
C506
C521 CB310
R222

R223

R245
R50 2

R503
L503 D503

R505 Q501
R5 06

R221
Q505

R246

X702 X703
D5 02

Figure 3-10 Resistor for VDDSB

User Manual 3-16 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Configuration

4 TriBoard Configuration

4.1 HW Boot Configuration

3
4.

0.

0.

4.
P1

P1

P1

P1
on

1 2 3 4

Figure 4-1 HW Configuration DIP-Switches

The picture above shows the definition of the boot HW configuration switch. The meaning of the switches will be
described in the following table (Table 4-1).

Note: The ON position of the switch is equal to a logical LOW at the dedicated pin.

4.1.1 Default Pad State

P14.4 / HWCFG6 is used to select the Default Pad State. Dipswitch 1 used to select this.
In case that dispswitch1 is set to ON then all I/O pins are in tristate otherwise the internal pull-up devices are
enabled on the I/O pins. Please note that after change Dipswitch 1 you must make a power cycle (switch off ->
switch on) to use the new configuration.
In case that TriState is selected (Dipswitch 1 is set to ON) then the I/O pins are floating. If you need a specific level
on different pins during startup (e.g. driver pins) then you must add the needed pull device (up or down). Some
pins (especially the HWCFG pins) haven always the needed external pull-up and/or pull-down resistor assembled
on the board.

4.1.2 Bootmode

Table 4-1 User Startup Modes 1)2)3)

HWCFG[5...3] Type of Boot 2 3 4
XX1 Start-up mode is selected by Boot Mode Index X X OFF
110 Internal Start from Flash OFF OFF ON
100 Alternate Boot Mode, Generic Bootstrap Loader on fail (P14.0/P14.1) ON OFF ON
010 Alternate Boot Mode, ASC Bootstrap Loader on fail (P15.2/P15.3) OFF ON ON
000 Generic Bootstrap Loader (P14.0/P14.1) ON ON ON
1) The shadowed line indicates the default setting.
2) ’x’ represents the don’t care state.
3) 2 to 4 are the Dip Switch numbers.

User Manual 4-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Configuration

4.2 Assembly Options

4.2.1 General optional resistors

Table 4-2 General optional resistors (default assembly in brackets)

Component Description
R202 Connect P20.2 (/TESTMODE) to GND (not assembled)
R203 XTAL1 Rload (50 Ohm) (not assembled)
R206 XTAL Rparallel (not assembled)
R207 XTAL2 Rserial (assembled)
R238 Switch off EVRC (not assembled)
R240 Switch off EVR33 (not assembled)
R390 Connect V_STBY to toggle LEDs D302...D305 (assembled)
R399 Connect V_UC to toggle LEDs D306...D309 (assembled)
R423 Connect P20.0 with miniWiggler JDS (not assembled)
R424 Connect P20.0 with OCDS1 connector (not assembled)
R425 Connect P20.1 with OCDS1 connector (not assembled)
R426 Connect P20.2 with OCDS1 connector (not assembled)
R427 Connect P20.1 with USR1 of miniWiggler JDS (not assembled)
R428 Connect P20.2 with USR1 of miniWiggler JDS (not assembled)
R429 Connect P21.6 (DAP3) with USR1 of DAP (assembled)
R430 Connect P20.2 with USR1 of DAP (not assembled)
R433 Connect P20.1 with ETK connector (not assembled)
R439 Connect P21.7 with ETK connector (not assembled)
R508 Connect pin MPS of TLF35584 to V_CO (assembled)
R524 Connect VDDP3 to V_UC (not assembled)
R525 Connect VDDP3 to +3V3 (not assembled)

Note: All resistors are red marked in the following figures.

User Manual 4-2 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Configuration

X306

X604 X601
C3 06
R383

C310 X202
L301
R390 R399 S202
C311 C318 CB319
Y301

X404

R256
D30 2

D30 3

D30 4

D30 5

D30 6

D30 7

D30 8

D30 9
Y401 R382

C309
CB318
R392 R393 R394 R395 R396 R397 R398

R39 1
CB4 01

R3104
U3 07

R2 55
R402
R439
BU40 1

R3100 X403
R3109

R31 03

X201
C320

CB317 R3101
R403 U401 R386
R3102
R226
CB405

R3108

S201
R377
CB4 08
C402
L4 01

R380 R379 R225

Q301

R375

R240
U4 04

R376
CB416

CB418
R401

CB419

CB402 CB414
R453
U407 U408

R230

R232

R234

R236

R217
D401 D402 U406 R241
R45 5
T 301

CB417

R456
R4 46

X30 1

R411
X30 3

R335

R444
R336

R428

CB415

R429
R451

R427 R430
R454

U201
R33 7

C30 1

R213 X402
R423

R212 R452
R329
X4 01

R424

C202
R324
R202
R206

CB20 1
R205
T30 2

R201 R204

Y201
R20 7
R426

R425

C201
X30 2

CB202
X30 4

R53 1

R354
R532

R203
R355

R35 6

R344
R3 57

C302

S5 01

U502
C505
D504 D507
C50 4

C5 03

D506
C5 08
C5 09

R50 8
CB502

C303 X502

R34 6
L502

D508 D505

U3 05

CB309
R509 R247
X3 05

R348
R361
C502 R349

C522
D301
R359

X40 6

U501 R347
S502
R249

C507
CB5 01

R2 48

R507 R244
R457
L 501

R5 01
X50 1

X603 X602
C501

Figure 4-2 Location of general optional resistors on Top Side

C316
C315
C314

C317

X701 X704 R389

R38 5

C308
R384

C30 7

C305 CB315

R3 88
R260 R258
R378

R3105 CB312 C312

R3110

C319
R310

CB4 12

C313
R311 1

CB413

C404
CB316
C406
CB314 C405
R370
R310 6

CB409
R257
R259

R3 107

R372
CB313
CB4 04

C4 01

R414 R404
RN301 CB311 L402
C4 03
R5 25

R419
R21 9

R440 CB411
R211

R371
CB41 0

R418 R442 U405

CB40 3

Q403
R381 R420
CB209
R416
R441
R21 8

R433 R422 R437 R417 Q402 R405

R231

R406

R254 R250 R252 R449

R237

R235

R233

R443
L20 1

R421

R448
R4 13

R410

R438 U402
R253 R251 U403
R447
R450

R436 Q401
CB406
R41 2

R307
CB208
CB407
R3 08

R3 09
R304

R407
R373 R415
R4 31

R409 R445
R374
R524

R302
C5 19

R328
RN302

CB30 1

R334
R303

U301

R305

R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333
R408

CB305
U303

R306 R321
R522 CB303
R338

R326
R322 R332
CB51 7

CB515

R317 R325 R331

R216

R215

R31 9
R214

R318

R343
CB5 18

CB2 06
R2 09

R314
CB516

C207 R340
R312
R350

Q502 CB307
R31 5

CB510 C208
CB302
R208

CB513

C206 R341
R353
U302

U30 4

R313 CB308
CB205 R342
C2 05

C2 04

C515

R311 CB306
R358
R3 16

R520 CB204 R533 R351

C407

R521 C408 R536 R352

Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
R238
C518
C520
Q504

R535
R239
C203 R511 C304
U306
C51 1
CB5 06

C510

C512

U503 Q506
R504

R220
R534

D501
R3 60

C506
C521 CB310
R222

R223

R245
R50 2

R503
L503 D503

R505 Q501
R5 06

R221
Q505

R246

X702 X703
D5 02

Figure 4-3 Location of general optional resistors on Bottom Side

User Manual 4-3 V2.3
TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Configuration

4.2.2 Resistors for peripherals

Table 4-3 Resistors for peripherals (default assembly in brackets)

Component Description
R220 Connect V_VR with VDDM (assembled)
R221 Connect +3V3 with VDDM (not assembled)
R222 Connect VAREF1 with VDDM (assembled)
R223 Connect VAREF2 with VDDM (assembled)
R301 Connect P20.7 with RXD of CAN0 transceiver (assembled)
R302 Connect P20.8 with TXD of CAN0 transceiver (assembled)
R303 Connect P14.1 with RXD of CAN0 transceiver (not assembled)
R304 Connect P14.0 with TXD of CAN0 transceiver (not assembled)
R311 Connect P23.0 with RXD of CAN1 transceiver (assembled)
R312 Connect P23.1 with TXD of CAN1 transceiver (assembled)
R313 Connect P00.1 with RXD of CAN1 transceiver (not assembled)
R314 Connect P00.0 with TXD of CAN1 transceiver (not assembled)
R320 Connect P14.10 with TXD of ERAY-A transceiver (assembled)
R321 Connect P14.9 with TXDEN of ERAY-A transceiver (assembled)
R322 Connect P14.8 with RXD of ERAY-A transceiver (assembled)
R323 Connect P32.3 with EN of ERAY-A transceiver (assembled)
R324 Connect P32.2 with ERRN of ERAY-A transceiver (assembled)
R325 Connect P02.1 with RXD of ERAY-A transceiver (not assembled)
R326 Connect P02.4 with TXDEN of ERAY-A transceiver (not assembled)
R327 Connect P02.0 with TXD of ERAY-A transceiver (not assembled)
R328 Connect P10.2 with EN of ERAY-A transceiver (not assembled)
R329 Connect P10.1 with ERRN of ERAY-A transceiver (not assembled)
R340 Connect P14.5 with TXD of ERAY-B transceiver (assembled)
R341 Connect P14.6 with TXDEN of ERAY-B transceiver (assembled)
R342 Connect P14.7 with RXD of ERAY-B transceiver (assembled)
R343 Connect P20.10 with EN of ERAY-B transceiver (assembled)
R344 Connect P20.9 with ERRN of ERAY-B transceiver (assembled)
R348 Connect P15.4 with SCL of I2C Eeprom (assembled)
R349 Connect P15.5 with SDA of I2C Eeprom (assembled)
R364 Connect P15.1 with RXD of LIN1 transceiver (assembled)
R365 Connect P15.0 with TXD of LIN1 transceiver (assembled)
R310 Connect P11.5 with CLOCKOUT of Ethernet PHY (assembled)
R370 Connect P11.12 with RXC of Ethernet PHY (assembled)
R371 Connect CLKOUT of Ethernet PHY with TXC of Ethernet PHY (not assembled)
R372 Connect P11.11 with RXCTL of Ethernet PHY (assembled)
R373 Connect P11.4 with TXC of Ethernet PHY (assembled)

User Manual 4-4 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Configuration

Table 4-3 Resistors for peripherals (default assembly in brackets) (continued)

Component Description
R374 Connect P11.6 with TXCTL of Ethernet PHY (assembled)
R375 Connect P12.1 with MDIO of Ethernet PHY (assembled)
R376 Connect P12.0 with MDC of Ethernet PHY (assembled)
R377 Connect P15.8 with MDINT of Ethernet PHY (not assembled)
RN301 Connect P11.7...10 with RDX3...0 of Ethernet PHY (assembled)
RN302 Connect P11.0...3 with TDX3...0 of Ethernet PHY (assembled)
R436 Connect P14.0 with RXD of USB to UART (assembled)
R437 Connect P14.1 with TXD of USB to UART (assembled)
R438 Connect P15.2 with RXD of USB to UART (not assembled)
R440 Connect P15.3 with TXD of USB to UART (not assembled)

Note: All resistors are red marked in the following figures

X306

X604 X601
C3 06
R383

X202
C310 L301
R390 R399 S202
C311 C318 CB319
Y301

X404
R256
D30 2

D30 3

D30 4

D30 5

D30 6

D30 7

D30 8

D30 9

Y401 R382

C309

CB318
R392 R393 R394 R395 R396 R397 R398
R39 1
CB4 01

R3104
U3 07

R2 55

R402
R439
BU40 1

R3100 X403
R3109

R31 03

X201
C320

CB317 R3101
R403 U401 R386
R3102
R226
CB405

R3108
S201

R377
CB4 08
C402
L4 01

R380 R379 R225

Q301

R375
R240

R376
U4 04

CB416

CB418
R401

CB419

CB402 CB414
R453
U407 U408
R230

R232

R234

R236

R217

D401 D402 R241

U406
R45 5
T 301

CB417

R456
R4 46

X30 1

R411
X30 3

R335

R444
R336

R428

CB415
R451

R429
R427 R430
R454

U201
R33 7

C30 1

R213 X402
R423

R212 R452
R329
X4 01

C202
R424

R324
R202
R206
CB20 1

R205
T30 2

R201 R204
Y201
R20 7
R426

R425

X30 2

C201
CB202
X30 4

R53 1

R354
R532

R203
R355

R35 6

R344
R3 57

C302

S5 01

U502
C505
D504 D507
C50 4

C5 03

D506
C5 08
C5 09

R50 8
CB502

C303 X502
R34 6
L502

D508 D505
U3 05

CB309

R509
X3 05

R247
R348

R361
C502 R349
C522
D301
R359

X40 6

U501 R347
S502
R249

C507
CB5 01

R2 48

R507 R244
R457
L 501

R5 01
X50 1

X603 X602
C501

Figure 4-4 Location of peripheral resistors on Top Side

User Manual 4-5 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
TriBoard Configuration

C316
C315
C314

C317

X701 X704 R389

R38 5
C308

R384

C30 7
C305 CB315

R3 88
R260 R258

R378
R3105 CB312 C312

R3110
C319

R310

CB4 12
C313

R311 1

CB413
C404
CB316
C406
CB314 C405
R370

R310 6
CB409

R257
R259

R3 107
R372
CB313

CB4 04

C4 01
R414 R404
RN301 CB311 L402

C4 03
R5 25
R419

R21 9
R440 CB411

R211
R371

CB41 0
R418 R442 U405

CB40 3
Q403
R381 R420
CB209
R416
R441

R21 8
R433 R422 R437 R417 Q402 R405

R231

R406
R254 R250 R252 R449

R237

R235

R233
R443

L20 1

R421
R448

R4 13

R410
R438 U402
R253 R251 U403
R447

R450
R436 Q401
CB406

R41 2
R307
CB208

CB407
R3 08

R3 09
R304
R407
R373 R415

R4 31
R409 R445
R374

R524
R302

C5 19
R328

RN302

CB30 1

R334
R303

U301

R305
R323
CB520 CB512 D403 R327 R330 CB304
CB519 R301 R320
CB203 R333

R408
CB305

U303
R306 R321
R522 CB303

R338
R326
R322 R332

CB51 7

CB515
R317 R325 R331
R216

R215

R31 9
R214

R318
R343

CB5 18

CB2 06
R2 09

R314

CB516
C207 R340
R312

R350
Q502 CB307

R31 5
CB510 C208

CB302
R208

CB513

C206 R341
R353

U302

U30 4
R313 CB308
CB205 R342

C2 05

C2 04

C515
R311 CB306
R358

R3 16
R520 CB204 R533 R351

C407
R521 C408 R536 R352
Q 503
R523 R513 R538
R362
R364
R512 R537
X405 R510 R365 R363
R238
C518
C520

Q504
R535
R239
C203 R511 C304
U306

C51 1
CB5 06

C510

C512
U503 Q506

R504
R220

R534
D501

R3 60
C506
C521 CB310
R222

R223

R245

R50 2
R503
L503 D503

R505 Q501

R5 06
R221

Q505
R246

X702 X703

D5 02
Figure 4-5 Location of peripheral resistors on Bottom Side

User Manual 4-6 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Signal (on board used) Description

5 Signal (on board used) Description

For more information about the signals please see the user manual/datasheet for TC3X7 and/or the schematics
of the board.
All not mentioned signals are not used on the board and can be used outside. Optional marked signals are used
only if they are connected (default is that they are not used on the board).

5.1 Power Signals

Table 5-1 Power Signals

Short name Description
VCC_IN Supply Input (3,5V...40V)
VIN Input Voltage of Power Supply Device
GND Ground
V_PREPEG Pre Regulator Voltage (~5,8V)
V_UC Microcontroller Supply Voltage (5V or 3,3V depends on assembled TLF35584)
V_CO Communication Supply Voltage (5V)
V_VR Reference Supply Voltage (5V)
V_STBY Standby Supply Voltage (5V or 3,3V depends on assembled TLF35584)
VDD Core Supply Voltage (1,25V)
VDDSB Emulation Stand-by SRAM Supply Voltage (1,25V)
VDDP3 Flash Power Supply Voltage (3,3V)
VFLEX Flexport Supply Voltage (3,3V)
VEXTOSC Oscillator Port Supply Voltage (5V or 3,3V depends on assembled TLF35584)
VDDOSC Oscillator Core Supply Voltage (1,25V)
VSSOSC Oscillator Ground
VDDM ADC Analog Part Supply Voltage (5V or 3,3V selectable via 0R resistors)
VAREF1 ADC Reference Voltage 1 (VDDM)
VAREF2 ADC Reference Voltage 2 (VDDM)
VDD_USB Supply Voltage from USB (5V)
VDD_FT Supply Voltage FT2232HL device (3,3V)

5.2 Reset Signals

Table 5-2 Reset Signals

Short name Description
/PORST Power On Reset
/DBG_PORST Power On Reset from debug connectors
/ESR0 External Service Request 0 (Hardware Reset)
/ESR1 External Service Request 1 (Non Maskable Interrupt)

User Manual 5-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Signal (on board used) Description

5.3 Config Signals

Table 5-3 Config Signals

Short name Description
P14.5 HWCFG1 (EVR33OFF / EVR33ON)
P14.2 HWCFG2 (EVRCOFF / EVRCON)
P14.4 HWCFG6 (Pins in tristate / Pins with pull-up)
P14.3 HWCFG3 (Boot from pins / Boot from Flash BMI)
P10.5 HWCFG4 (see boot configuration Table 4-1)
P10.6 HWCFG5 (see boot configuration Table 4-1)

5.4 Clock Signals

Table 5-4 Clock Signals

Short name Description
XTAL1 Crystal Oscillator Input
XTAL2 Crystal Oscillator Output

5.5 Debug Signals

Table 5-5 Debug Signals

Short name Description
/TRST Test Reset
DAP0 Device Access Port Line 0 / Test Data Clock (TCK)
DAP1 Device Access Port Line 1 / Test Data Select (TMS)
DAP2 Device Access Port Line 2 / Test Data Output (TDO)
DAPE0 Device Access Port Line 0 (Emulation part)
DAPE1 Device Access Port Line 1 (Emulation part)
DAPE2 Device Access Port Line 2 (Emulation part)
P21.6 Test Data Input (TDI)
DAP0_A DAP0 / DAPE0 / TCK from debug connectors
DAP1_A DAP1 / DAPE1 / TMS from debug connectors
P21.7 DAP2 / DAPE2 / TDO from debug connectors
P33.6 Device Access Port Line 0 (standby controller)
P33.7 Device Access Port Line 1 (standby controller)
P20.2 Test Mode Select Input
P20.1 TriCore Breakpoint Input
P20.0 TriCore Breakpoint Output
AGBT_CLK_P/_N AGBT Clock Input
AGBT_TX0_P/_N AGBT Transmit Output
AGBT_ERR AGBT Error Output

User Manual 5-2 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Signal (on board used) Description

5.6 Peripheral Signals

Table 5-6 Peripheral Signals

Short name Description
P14.1 ASCLIN0 Receive Input A
CAN01 Receive Input B (optional)
P14.0 ASCLIN0 Transmit Output
CAN01 Transmit Output (optional)
P15.3 ASCLIN0 Receive Input B (optional)
P15.2 ASCLIN0 Transmit Output (optional)
P15.1 ASCLIN1 Receive Input A
P15.0 ASCLIN1 Transmit Output
P15.4 I2C0 Serial Clock
P15.5 I2C0 Serial Data Input C und Output
P20.7 CAN00 Receive Input B
P20.8 CAN00 Transmit Output
P23.0 CAN10 Receive Input C
P23.1 CAN10 Transmit Output
P00.1 CAN10 Receive Input A (optional)
P00.0 CAN10 Transmit Output (optional)
P14.10 E-Ray Channel A Transmit Data Output
P14.9 E-Ray Channel A Transmit Data Output enable
P14.8 E-Ray Channel A Receive Data Input 0
P32.3 E-Ray Channel A Enable Output
P32.2 E-Ray Channel A Error Input
P14.5 E-Ray Channel B Transmit Data Output
P14.6 E-Ray Channel B Transmit Data Output enable
P14.7 E-Ray Channel B Receive Data Input 0
P20.10 E-Ray Channel B Enable Output
P20.9 E-Ray Channel B Error Input
P02.0 E-Ray Channel A Transmit Data Output (optional)
P02.4 E-Ray Channel A Transmit Data Output enable (optional)
P02.1 E-Ray Channel A Receive Data Input 2 (optional)
P10.2 E-Ray Channel A Enable Output (optional)
P10.1 E-Ray Channel A Error Input (optional)
TXD3 Ethernet TXD3 Output (P11.0)
TXD2 Ethernet TXD2 Output (P11.1)
TXD1 Ethernet TXD1 Output (P11.2)
TXD0 Ethernet TXD0 Output (P11.3)
TXCLK Ethernet TXCLK Output (P11.4)

User Manual 5-3 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Signal (on board used) Description

Table 5-6 Peripheral Signals (continued)

Short name Description
REFCLK Ethernet GREFCLK Input (P11.5)
TCTL Ethernet TCTL Output (P11.6)
RXD3 Ethernet RXD3 Input A (P11.7)
RXD2 Ethernet RXD2 Input A (P11.8)
RXD1 Ethernet RXD1 Input A (P11.9)
RXD0 Ethernet RXD0 Input A (P11.10)
RCTL Ethernet RCTL Input A (P11.11)
RXCLK Ethernet RXCLK Input A (P11.12)
P12.0 Ethernet Management Data Clock Output (MDC)
P12.1 Ethernet Management Data Input/Output (MDIO)
P15.8 Ethernet MD Interrupt Input (optional)
P14.2 QSPI2 Slave Select Output 1 for SCS of TLF35584
P15.3 QSPI2 Master Clock Output for SCL of TLF35584
P15.6 QSPI2 Master Transmit Output for SDI of TLF35584
P15.7 QSPI2 Master Receive Input B for SDO from TLF35584
P14.3 Output for Watchdog Input of TLF35584
P33.8 SMU_FSP0 Output for Error Signal Input of TLF35584
P33.9 Input for Safe State Signal 1 from TLF35584
P33.10 Output for Wake/Inhibit Input of TLF35584
P20.0 HSCT0/1 System Clock
RXD0_N HSCT0 Data Negative Input (P21.2)
RXD0_P HSCT0 Data Positive Input (P21.3)
TXD0_N HSCT0 Data Negative Output (P21.4)
TXD0_P HSCT0 Data Positive Output (P21.5
RXD1_N HSCT1 Data Negative Input (P21.0)
RXD1_P HSCT1 Data Positive Input (P21.1)
TXD1_N HSCT1 Data Negative Output (P22.2)
TXD1_P HSCT1 Data Positive Output (P22.3
P20[11...14] On board LED’s
P33[4...7] On board LED’s (standby voltage supplied)

User Manual 5-4 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6 Connector Pin Assignment

The TriBoard will be shipped with four male (plug) connectors on top layer and four female (socket) connectors
on bottom layer. The default connectors are 80-pol. Board to Board connectors from Samtec:

http://www.samtec.com

Plug:
FTSH-140-02-L-DV-ES-A

Socket:
FLE-140-01-G-DV-A

6.1 On Board only used signals

Following port pins are only used on board and are not connected to any connector also not via resistor:

Table 6-1 On Board only used Signals

Short name Description
P32.0 Used as VGATE1N/VCAP0 for EVRC
P32.1 Used as VGATE1P/VCAP1 for EVRC
P14.2 Used as HWCFG2 and Slave Select Output (SLSO21) to TLF35584
P14.4 Used as HWCFG6 and Output to Watchdog Input of TLF35584
P14.5 Used as HWCFG1 and E-Ray Channel B Transmit Data Output
P14.6 Used as E-Ray Channel B Transmit Data Output enable
P11.0 Used as Gigabit Transmit Data Output 3 for RGMII
P11.1 Used as Gigabit Transmit Data Output 2 for RGMII
P11.2 Used as Gigabit Transmit Data Output 1 for RGMII
P11.3 Used as Gigabit Transmit Data Output 0 for RGMII
P11.4 Used as Gigabit Transmit Clock Output for RGMII
P11.5 Used as Gigabit Reference Clock input for RGMII (125 MHz high precision)
P11.6 Used as Gigabit Transmit Control Output for RGMII
P11.7 Used as Gigabit Receive Data Input 3 for RGMII
P11.8 Used as Gigabit Receive Data Input 2 for RGMII
P11.9 Used as Gigabit Receive Data Input 1 for RGMII
P11.10 Used as Gigabit Receive Data Input 0 for RGMII
P11.11 Used as Gigabit Receive Data Control Input for RGMII
P11.12 Used as Gigabit Receive Clock Input for RGMII

User Manual 6-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.2 TC397/TC387/TC377/TC3E7 Connector / Top View

BUS EXPANSION (X601,X701) PERIPHERALS (X602,X702)

GND 1 2 GND GND 1 2 GND
GND 3 4 GND GND 3 4 GND
5 6 P21.6 VCC_IN 5 6 VCC_IN
7 8 P21.7 VCC_IN 7 8 VCC_IN
9 10 P22.4 9 10 P22.8
11 12 P22.5 11 12 P22.9
13 14 P22.6 13 14 P22.10
15 16 /ESR1 15 16 /ESR0
17 18 P22.7 17 18 P22.11
19 20 GND 19 20 GND
21 22 21 22 /PORST
23 24 P10.5 23 24 P23.3
25 26 P10.4 25 26 P23.4
27 28 P10.2 27 28 P23.1
29 30 P13.1 29 30 P22.1
31 32 P13.0 31 32 P22.0
33 34 P13.3 33 34 P22.3
35 36 P13.2 35 36 P22.2
37 38 P20.9 37 38 P20.10
39 40 P20.13 39 40 P00.4
41 42 P33.5 41 42 P20.6
43 44 P20.3 43 44 P20.2
45 46 P00.0 45 46 P00.3
47 48 P00.1 47 48 P00.2
49 50 P21.2 GND 49 50 GND
51 52 P21.3 XTAL1 51 52 P32.4
53 54 P21.4 XTAL2 53 54
55 56 P21.5 P15.3 55 56 P15.5
57 58 P15.2 57 58 P15.4
59 60 P14.1 59 60 P15.1
61 62 P14.0 61 62 P15.0
63 64 P20.11 63 64 P00.12
65 66 P20.14 65 66 P00.11
67 68 P20.12 67 68 P00.5
69 70 P20.7 69 70 P20.8
71 72 P20.0 P15.8 71 72 P10.8
73 74 P10.7 73 74 P10.3
75 76 VDDSB 75 76 GND
77 78 VEXT 77 78 +3V3
P21.0 79 80 P21.1 VEXT 79 80 +3V3

Figure 6-1 Connector for TC397/TC387/TC377/TC3E7 - Pinout (Part I, Top View)

User Manual 6-2 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

ADC (X603, X703) GTM / PORTS (X604,X704)

GND 1 2 GND GND 1 2 GND
GND 3 4 GND GND 3 4 GND
AN0 5 6 AN16 P00.9 5 6 P11.14
AN1 7 8 AN17 P00.10 7 8 P11.15
AN2 9 10 AN18 P02.0 9 10
AN3 11 12 AN19 P02.1 11 12
AN4 13 14 AN20 P02.2 13 14
AN5 15 16 AN21 P02.3 15 16
AN6 17 18 AN22 P02.4 17 18 P14.7
AN7 19 20 AN23 P02.5 19 20 P14.8
AN8 21 22 AN24 P02.9 21 22 P14.9
AN9 23 24 AN25 P02.10 23 24 P14.10
AN10 25 26 AN26 P02.11 25 26 P15.6
AN11 27 28 AN27 P01.3 27 28 P15.7
AN12 29 30 AN28 P01.4 29 30 P20.1
AN13 31 32 AN29 P10.0 31 32 P01.5
AN14 33 34 AN30 P10.1 33 34 P01.6
AN15 35 36 AN31 P10.6 35 36 P23.0
GND 37 38 GND P12.0 37 38 P23.2
VDDM 39 40 VAREF1 P12.1 39 40 P23.5
GND 41 42 VAREF2 41 42 P23.6
GND 43 44 GND 43 44 P23.7
AN32 45 46 AN40 45 46
AN33 47 48 AN41 47 48
AN34 49 50 AN42 49 50 P32.2
AN35 51 52 AN43 51 52 P32.3
AN36 53 54 AN44 53 54 P32.5
AN37 55 56 AN45 55 56 P33.8
AN38 57 58 AN46 57 58 P33.9
AN39 59 60 AN47 59 60 P33.10
GND 61 62 GND 61 62 P33.13
P33.3 63 64 P33.6 63 64 P33.14
P33.2 65 66 P33.0 65 66 P33.15
P33.1 67 68 P33.4 P11.13 67 68 P32.6
VEXT 69 70 +3V3 P34.1 69 70 P32.7
P02.6 71 72 P00.6 P34.2 71 72 P34.4
P02.7 73 74 P00.7 P34.3 73 74 P34.5
P02.8 75 76 P00.8 VFLEX 75 76 P01.7
P33.7 77 78 P14.3 VEXT 77 78 +3V3
P33.11 79 80 P33.12 VEXT 79 80 +3V3

Figure 6-2 Connector for TC397/TC387/TC377/TC3E7 - Pinout (Part II, Top View)

User Manual 6-3 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.3 TC367 Connector / Top View

BUS EXPANSION (X601,X701) PERIPHERALS (X602,X702)

GND 1 2 GND GND 1 2 GND
GND 3 4 GND GND 3 4 GND
5 6 P21.6 VCC_IN 5 6 VCC_IN
7 8 P21.7 VCC_IN 7 8 VCC_IN
9 10 9 10
11 12 11 12
13 14 13 14
15 16 /ESR1 15 16 /ESR0
17 18 17 18
19 20 GND 19 20 GND
21 22 21 22 /PORST
23 24 P10.5 23 24 P23.3
25 26 P10.4 25 26 P23.4
27 28 P10.2 27 28 P23.1
29 30 P13.1 29 30 P22.1
31 32 P13.0 31 32 P22.0
33 34 P13.3 33 34 P22.3
35 36 P13.2 35 36 P22.2
37 38 P20.9 37 38 P20.10
39 40 P20.13 39 40 P00.4
41 42 P33.5 41 42 P20.6
43 44 P20.3 43 44 P20.2
45 46 P00.0 45 46 P00.3
47 48 P00.1 47 48 P00.2
49 50 P21.2 GND 49 50 GND
51 52 P21.3 XTAL1 51 52 P32.4
53 54 P21.4 XTAL2 53 54
55 56 P21.5 P15.3 55 56 P15.5
57 58 P15.2 57 58 P15.4
59 60 P14.1 59 60 P15.1
61 62 P14.0 61 62 P15.0
63 64 P20.11 63 64 P00.12
65 66 P20.14 65 66 P00.11
67 68 P20.12 67 68 P00.5
69 70 P20.7 69 70 P20.8
71 72 P20.0 P15.8 71 72 P10.8
73 74 P10.7 73 74 P10.3
75 76 VDDSB 75 76 GND
77 78 VEXT 77 78 +3V3
P21.0 79 80 P21.1 VEXT 79 80 +3V3

Figure 6-3 Connector for TC367 - Pinout (Part I, Top View)

User Manual 6-4 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

ADC (X603, X703) GTM / PORTS (X604,X704)

GND 1 2 GND GND 1 2 GND
GND 3 4 GND GND 3 4 GND
AN0 5 6 AN16 P00.9 5 6 P11.14
AN1 7 8 AN17 P00.10 7 8 P11.15
AN2 9 10 AN18 P02.0 9 10
AN3 11 12 AN19 P02.1 11 12
AN4 13 14 AN20 P02.2 13 14
AN5 15 16 AN21 P02.3 15 16
AN6 17 18 AN22 P02.4 17 18 P14.7
AN7 19 20 AN23 P02.5 19 20 P14.8
AN8 21 22 AN24 21 22 P14.9
AN9 23 24 AN25 23 24 P14.10
AN10 25 26 AN26 25 26 P15.6
AN11 27 28 AN27 27 28 P15.7
AN12 29 30 AN28 29 30 P20.1
AN13 31 32 AN29 P10.0 31 32
AN14 33 34 AN30 P10.1 33 34
AN15 35 36 AN31 P10.6 35 36 P23.0
GND 37 38 GND P12.0 37 38 P23.2
VDDM 39 40 VAREF1 P12.1 39 40 P23.5
GND 41 42 41 42
GND 43 44 GND 43 44
AN32 45 46 AN40 45 46
AN33 47 48 AN41 47 48
AN34 49 50 AN42 49 50 P32.2
AN35 51 52 AN43 51 52 P32.3
AN36 53 54 AN44 53 54
AN37 55 56 AN45 55 56 P33.8
AN38 57 58 AN46 57 58 P33.9
AN39 59 60 AN47 59 60 P33.10
GND 61 62 GND 61 62 P33.13
P33.3 63 64 P33.6 63 64
P33.2 65 66 P33.0 65 66
P33.1 67 68 P33.4 P11.13 67 68
VEXT 69 70 +3V3 69 70
P02.6 71 72 P00.6 71 72
P02.7 73 74 P00.7 73 74
P02.8 75 76 P00.8 VFLEX 75 76
P33.7 77 78 P14.3 VEXT 77 78 +3V3
P33.11 79 80 P33.12 VEXT 79 80 +3V3

Figure 6-4 Connector for TC367 - Pinout (Part II, Top View)

User Manual 6-5 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.4 TC337/TC327 Connector / Top View

BUS EXPANSION (X601,X701) PERIPHERALS (X602,X702)

GND 1 2 GND GND 1 2 GND
GND 3 4 GND GND 3 4 GND
5 6 P21.6 VCC_IN 5 6 VCC_IN
7 8 P21.7 VCC_IN 7 8 VCC_IN
9 10 P22.4 9 10
11 12 11 12
13 14 13 14
15 16 /ESR1 15 16 /ESR0
17 18 17 18
19 20 GND 19 20 GND
21 22 21 22 /PORST
23 24 P10.5 23 24
25 26 P10.4 25 26
27 28 P10.2 27 28 P23.1
29 30 P13.1 29 30 P22.1
31 32 P13.0 31 32 P22.0
33 34 P13.3 33 34 P22.3
35 36 P13.2 35 36 P22.2
37 38 P20.9 37 38 P20.10
39 40 P20.13 39 40 P00.4
41 42 P33.5 41 42 P20.6
43 44 P20.3 43 44 P20.2
45 46 P00.0 45 46 P00.3
47 48 P00.1 47 48 P00.2
49 50 P21.2 GND 49 50 GND
51 52 P21.3 XTAL1 51 52 P32.4
53 54 P21.4 XTAL2 53 54
55 56 P21.5 P15.3 55 56 P15.5
57 58 P15.2 57 58 P15.4
59 60 P14.1 59 60 P15.1
61 62 P14.0 61 62 P15.0
63 64 P20.11 63 64 P00.12
65 66 P20.14 65 66 P00.11
67 68 P20.12 67 68 P00.5
69 70 P20.7 69 70 P20.8
71 72 P20.0 P15.8 71 72 P10.8
73 74 P10.7 73 74 P10.3
75 76 VDDSB 75 76 GND
77 78 VEXT 77 78 +3V3
P21.0 79 80 P21.1 VEXT 79 80 +3V3

Figure 6-5 Connector for TC337/TC327 - Pinout (Part I, Top View)

User Manual 6-6 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

ADC (X603, X703) GTM / PORTS (X604,X704)

GND 1 2 GND GND 1 2 GND
GND 3 4 GND GND 3 4 GND
AN0 5 6 P00.9 5 6
AN1 7 8 P00.10 7 8
AN2 9 10 P02.0 9 10
AN3 11 12 P02.1 11 12
AN4 13 14 P02.2 13 14
AN5 15 16 P02.3 15 16
AN6 17 18 P02.4 17 18 P14.7
AN7 19 20 P02.5 19 20 P14.8
AN8 21 22 21 22 P14.9
AN9 23 24 23 24 P14.10
AN10 25 26 25 26 P15.6
AN11 27 28 27 28 P15.7
AN12 29 30 29 30 P20.1
AN13 31 32 P10.0 31 32
AN14 33 34 P10.1 33 34
AN15 35 36 P10.6 35 36
GND 37 38 GND 37 38
VDDM 39 40 VAREF1 39 40 P23.5
GND 41 42 41 42
GND 43 44 GND 43 44
AN32 45 46 45 46
AN33 47 48 47 48
AN34 49 50 49 50
AN35 51 52 51 52
AN36 53 54 53 54
AN37 55 56 55 56 P33.8
AN38 57 58 57 58 P33.9
AN39 59 60 59 60 P33.10
GND 61 62 GND 61 62
P33.3 63 64 P33.6 63 64
P33.2 65 66 P33.0 65 66
P33.1 67 68 P33.4 67 68
VEXT 69 70 +3V3 69 70
P02.6 71 72 P00.6 P34.2 71 72
P02.7 73 74 P00.7 P34.3 73 74
P02.8 75 76 P00.8 VEXT 75 76
P33.7 77 78 P14.3 VEXT 77 78 +3V3
P33.11 79 80 P33.12 VEXT 79 80 +3V3

Figure 6-6 Connector for TC337/TC327 - Pinout (Part II, Top View)

User Manual 6-7 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.5 Power connector pinout

+3,5V...40V

GND
Figure 6-7 Power connector pinout (Roka 520 2550

6.6 USB connector pinout

GND
VCC
D+
D-
ID

Figure 6-8 USB connector pinout (Micro USB B-type)

6.7 FlexRay™ (ERAY) connector pinout

1
2 4 6 8
0
1 3 5 7 9
GND
BM
BP

Figure 6-9 FlexRay™ (ERAY) connector pinout (IDC10)

6.8 CAN connector pinout

1
2 4 6 8
0
1 3 5 7 9
CANL
CANH
GND

GND

Figure 6-10 CAN connector pinout (IDC10)

User Manual 6-8 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.9 LIN connector pinout

1
2 4 6 8
0
1 3 5 7 9

GND

GND
VIN opt
BUS
Figure 6-11 LIN connector pinout (IDC10)

6.10 HSCT connector pinout

RXD_N
TXD_N
GND

2 4 6
GND

1 3 5
SYSCLK

RXD_P
TXD_P

Figure 6-12 HSCT connector pinout (IEE1394 6-conductor)

6.11 Ethernet connector pinout

J1
J2
J3
J4
J5
J6
J7
J8

Figure 6-13 Ethernet connector pinout (RJ45)

User Manual 6-9 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.12 OCDS1 connector pinout

/BRKOUT
/PORST
V_UC

GND
GND

GND
2 4 6 8 10 12 14 16

1 3 5 7 9 11 13 15
TMS

TDO

TDI

/TRST

TCK

/BRKIN
Figure 6-14 OCDS1 connector pinout (IDC16)

6.13 DAP connector pinout

USR1_IO
USR0_IO

/PORST
DAP1

DAP0

2 4 6 8 10

1 3 5 7 9
GND

GND
V_UC

GND

Key

Figure 6-15 DAP connector pinout (Samtec FTSH10)

User Manual 6-10 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.14 ETK connector pinout

TDO / DAP2
TCK / DAP0

/PORST
V_UC
TDI
2 4 6 8 10

1 3 5 7 9

TMS / DAP1
GND

/ESR0
BRKIO
/TRST

Figure 6-16 ETK connector pinout (Samtec TFM-105)

6.15 Ethernet miniWiggler power connector pinout

WAKEUP
VCC_IN

VDDSB
GND

1 2 3 4

Figure 6-17 Ethernet miniWiggler connector pinout (JST B4B-PH)

User Manual 6-11 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Connector Pin Assignment

6.16 AGBT connector pinout

AGBT CLK_N
AGBT CLK_P

AGBT ERR
/PORST
TGIOx
/TRST
V_UC
DAP0
DAP1

TDO
TDI
2 4 6 8 10 12 14 16 18 20 22
GND GND
1 3 5 7 9 11 13 15 17 19 21
AGBT TX0_N
GND

GND

GND
AGBT TX0_P

Figure 6-18 AGBT connector pinout (Samtec ASP-137969-01)

User Manual 6-12 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Schematic and Layout

7 Schematic and Layout

7.1 Known problems

7.1.1 Known problems on TriBoard TC3X7 TH V2.0(1)

R386 is assembled via wire wrap on version V2.0.

7.1.2 Known problems on TriBoard TC3X7 V2.0

No problems known.

7.2 Schematic

User Manual 7-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
 1 2 3 4 5 6 7 8

Figure 7-1

User Manual
/ESR1

/PORST
A A

/ESR0
Schematic and Layout

XTAL[1..2]

AN[0..47]
TriBoard Manual TC3X7

Schematic - Project
Clk_Cfg_Dbg_Ports_Adc.sch

Clock, Config, Debug, Ports and ADC

Connectm.sch
AN[0..47]
Connector Plug
AN[0..47]
XTAL[1..2] PORT[00..34] PORT[00..34]
wiggler_Dbg_con.sch

miniWiggler and Debug Connectors

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

DEBUG..
DEBUG.. DEBUG.. GETH.. XTAL[1..2]
B B
NC1[5..80]

/ESR0 PORT[00..34]
/ESR0

/PORST NC2[5..80]

/PORST

7-2
NC4[5..80]
/ESR1
GETH..

Peripherals.sch

On Board Peripherals
GETH..
Connectf.sch

PORT[00..34]
NC1[5..80]
NC2[5..80]
NC4[5..80]

PORT[00..34]

/ESR0
Connector Socket
AN[0..47]
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

NC4[5..80]
C C

XTAL[1..2]

NC2[5..80]

/ESR0
Supply.sch

Power Supply NC1[5..80]

/ESR0 /PORST

/PORST PORT[00..34] PORT[00..34]

/ESR1

/ESR1

D D

TriBoard TC3X7 Project

Sheet: 1 of 7 Infineon Technologies AG
ATV MC ACE ATV CES
Number: Am Campeon 1-12
Revision: 2.01 D-85579 Neubiberg
Date: 10.11.2017 Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard AURIX 2G\TriBoard TC3X7\TriBoard TC3X7 V2.X\TriBoard_TC3X7_V20.prj
1 2 3 4 5 6 7 8

V2.3
2019-09
 1 2 3 4 5 6 7 8

Figure 7-2
V_UC

User Manual
U201B
XTAL[1..2] R203 R201 CLOCK & TESTMODE VEXTOSC V_UC
AN[0..47] XTAL[1..2] R202 10K R209
U201E 50R_opt P20.2 H19 N20
P20.2 / TESTMODE VEXTOSC
EVADC / EDSADC VSSOSC opt 0R
AN0 T10 GND VDDOSC VDD CB201
AN0 / EDS3PA R204 R208
AN1 U10 XTAL1 M20 N19 100n

1
AN1 / EDS3NA XTAL1 VDDOSC
AN2 W9 FOR 5V ADC 0R 0R
A AN2 / EDS0PA R206 Y201 A
AN3 U9 CB202 VSSOSC
AN3 / EDS0NA R205 opt 20MHz R207
AN4 T9 VDDM V_VR XTAL2 M19 L20 100n

2
R244 AN4 R220 XTAL2 VSSOSC
AN7 AN5 Y9 Y5 0R 0R
AN5 VDDM
4K7 AN6 T8 1R2 JTAG / DAP / OCDS1 VSSOSC GND
AN6 C201 C202
AN7_I U8 CB204 /TRST L19
Schematic and Layout

AN7 10pF 10pF TRST

AN8 W8 Y4 470n DAP0 J16
C203 AN8 VSSM TCK / DAP0
AN9 U7 FOR 3,3V ADC DAP1 R212 K16
47nF AN9 TMS / DAP1 R213
AN10 Y8 GND VSSOSC VSSOSC DAP0 33R H17 H16
AN10 P21.6 / TDI P21.7 / TDO / DAP2
AN11 W7 +3V3 33R
AN11 R221 R214
GND AN12 T7 G19
AN12 / EDS0PB 0R P20.1 / TGI1N / TGO1N
AN13 W6 1R2_opt
R245 AN13 / EDS0NB
AN20 AN14 U6 DAP0_A DAPE / AGBT (ED only)
AN14 / EDS3PB
4K7 AN15 T6 AGBT_CLK_P K7 K14
AN15 / EDS3NB VSS / AGBTCLKP NC / DAPE0
TriBoard Manual TC3X7

AN16 W5 AGBT_CLK_N L7 G11 R225

AN16 VSS / AGBTCLKN VSS / DAPE1
AN17 U5 DAP1 AGBT_TX0_P P11 G10 R226 33R
C204 AN17 / P40.10 VSS / AGBTTX0P VSS / DAPE2
AN18 W4 VAREF1 VDDM AGBT_TX0_N P10 33R
47nF AN18 / P40.11 R222 R215 VSS / AGBTTX0N
AN19 W3 Y6 AGBT_ERR L14
AN19 / P40.12 VAREF1 0R VSS / AGBTERR
AN20_I Y3 6R8
AN20 / EDS2PA

DAPE0
DAPE2
DAPE1

GND AN21_I Y2 CB205 V_STBY DAP1_A TC3X7

AN21 / EDS2NA
DAP2

AN22 T5 Y7 2,2μF
AN22 VAGND1
AN23 R5 S202 DEBUG..
R246 AN23 R255 DEBUG..
AN21 AN24 W2 GND
AN24 / EDS2PB / P40.0 R256 47K
4K7 AN25 W1
AN25 / EDS2NB / P40.1
AN26 V2 P33.11 1K5
C205 AN26 / P40.2

DAP2
DAP0_A
DAPE1
DAP1_A
DAPE2
AN27 V1 GND
47nF AN27 / P40.3 R216 R217 R218 R219

DAPE0
AN28 U2 VAREF2 VDDM P21.7 P21.7
AN28 / P40.13 R223

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

P33.11
P20.2
P21.6
P20.1
AN29 U1 T1 0R 0R_opt 0R_opt 0R_opt
AN29 / P40.14 VAREF2
GND AN30 T4 6R8
B AN30 B
AN31_I R4 CB206 PORT[00..34]
AN31 PORT[00..34]
AN32 P4 T2 2,2μF
R247 AN32 / P40.4 VAGND2
AN31 AN33 R1
AN33 / P40.5
4K7 AN34 P5 GND U201C
AN34
AN35 R2 ON BOARD USED PERIPHERALS / PINS
C206 AN35 R252
AN36 N4 U201D P14.1 A15 B16 P14.0 P20.0
47nF AN36 / EDS1PA / P40.6 P14.1 / ARX0A P14.0 / ATX0
AN37 P2 PORTS 0R
AN37 / EDS1NA / P40.7 ASCLIN
AN38 N5 P00.0 G1 C19 P15.2 P15.1 A18 B20 P15.0
AN38 / EDS1PB / P40.8 P00.0 P15.2 P15.1 / ARX1A P15.0 / ATX1 R253
GND AN39 P1 P00.1 G2 P21.2

AN[0..47]
AN39 / EDS1NB / P40.9 P00.1
AN40 M5 P00.2 H1 D14 P15.8 P20.7 F19 F20 P20.8 0R
AN40 P00.2 P15.8 P20.7 / RXDCAN0B P20.8 / TXDCAN0
AN41 M4 P00.3 H2
R248 AN41 P00.3 CAN R254
AN44 AN42 L5 P00.4 J1 G20 P20.3 P23.0 V20 U19 P23.1 P21.3
AN42 P00.4 P20.3 P23.0 / RXDCAN4C P23.1 / TXDCAN4
AN43 L4 P00.5 J2

7-3
4K7 AN43 P00.5 0R
AN44_I N1 P00.6 J4 F17 P20.6 P14.2 E13 B17 P15.3
AN44 / EDS1PC P00.6 P20.6 P14.2 / SLSO21 / HWCFG2 P15.3 / SCLK2 R250
AN45_I N2 P00.7 K1 P15.7 D15 A16 P15.6 P21.4
C207 AN45 / EDS1NC P00.7 P15.7 / MRST2B P15.6 / MTSR2
AN46 M1 P00.8 K4 P20 P22.0 B15 P14.4 0R
47nF AN46 / EDS1PD P00.8 P22.0 QSPI / TLF35584 P14.4 / HWCFG6
AN47 M2 P00.9 K2 P19 P22.1 P33.9 Y14 W14 P33.8
AN47 / EDS1ND P00.9 P22.1 P33.9 P33.8 / SMU_FSP R251

Schematic - Clock, Config, Debug, Ports and ADC

P00.10 K5 W15 P33.10 P21.5
P00.10 P33.10
GND TC3X7 P00.11 L1 P16 P22.4 0R
P00.11 P22.4
P00.12 L2 P17 P22.5 P14.8 A13 D13 P14.7
P00.12 P22.5 P14.8 / RXDxA P14.7 / RXDxB
N16 P22.6 P14.9 D12 B13 P14.6 X201
R249 P22.6 P14.9 / TXENxA P14.6 / TXENxB R257
AN45 P01.3 G5 N17 P22.7 P14.10 D11 A14 P14.5 P21.0 3
P01.3 P22.7 P14.10 / TXDxA P14.5 / HWCFG1 / TXDxB TXDP
4K7 P01.4 G4 M16 P22.8 P32.2 Y18 E17 P20.9 0R 4
P01.4 P22.8 P32.2 P20.9 TXDN
P01.5 H5 M17 P22.9 P32.3 Y19 E19 P20.10 5
C208 P01.5 P22.9 P32.3 ERAY P20.10 R258 RXDP
P01.6 H4 L16 P22.10 P21.1 6
47nF P01.6 P22.10 RXDN
P01.7 J5 L17 P22.11 P15.5 E14 A17 P15.4 0R 1
P01.7 P22.11 P15.5 / SDA0 I2C P15.4 / SCL SYSCLK
2
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

GND
C GND P02.0 B1 U20 P23.2 HWCFG J20 TXD0_P C
P02.0 P23.2 P21.5 / TXD0P
V_UC P02.1 C2 T19 P23.3 P14.3 B14 K20 TXD0_N HSCT0-opt
P02.1 P23.3 P14.3 / HWCFG3 P21.4 / TXD0N
P02.2 C1 T20 P23.4 P10.5 B5 J19 RXD0_P
P02.2 P23.4 P10.5 / HWCFG4 P21.3 / RXD0P
P02.3 D2 T17 P23.5 P10.6 A4 K19 RXD0_N
R239 P02.3 P23.5 P10.6 / HWCFG5 P21.2 / RXD0N
P02.4 D1 R17 P23.6 H20 SYSCLK GND
R238 47K P02.4 P23.6 HSCT P20.0 / SYSCLK
P14.2 P02.5 E2 R16 P23.7 K17 RXD1_N
P02.5 P23.7 P21.0 / RXD1N
1K5_opt P02.6 E1 BUTTON J17 RXD1_P
P02.6 P21.1 / RXD1P
V_UC P02.7 F2 W18 P32.4 P33.11 Y15 R20 TXD1_N X202 GND
P02.7 P32.4 P33.11 P22.2 / TXD1N
P02.8 F1 T15 P32.5 R19 TXD1_P 2
S

P02.8 P32.5 P22.3 / TXD1P GND

P02.9 E4 U15 P32.6 1
R241 P02.9 P32.6 SYSCLK
P02.10 F5 U16 P32.7 P20.11 E20 W12 P33.4 P22.2 R259 6
R240 4K7 P02.10 P32.7 P20.11 LEDs P33.4 RXDN
P14.5 P02.11 F4 P20.12 D19 Y12 P33.5 0R 5
P02.11 P20.12 P33.5 RXDP
1K5_opt W10 P33.0 P20.13 D20 W13 P33.6 4
P33.0 P20.13 P33.6 TXDN
GND V_UC P10.0 A7 Y10 P33.1 P20.14 C20 Y13 P33.7 P22.3 R260 3
P10.0 P33.1 P20.14 P33.7 TXDP
P10.1 B7 W11 P33.2 0R
P10.1 P33.2
P10.2 A5 Y11 P33.3 P11.13 E6 E12 P12.0 HSCT1-opt
R231 P10.2 P33.3 P11.13 P12.0 / MDC
P10.3 A6 P11.14 D7 E11 P12.1
47K P10.3 P11.14 P12.1 / MDIO
HWCFG6 R230 P14.4 P10.4 B6 W16 P33.12 P11.15 D6
P10.4 P33.12 P11.15 GIGABIT ETHERNET
1K5 Y16 P33.13 REFCLK D8 D10 TXCLK
P33.13 P11.5 / GREFCLK P11.4 / TXCLK
V_UC P10.7 A3 T14 P33.14 B10 TDX0
P10.7 P33.14 P11.3 / TXD0
P10.8 B4 U14 P33.15 RXCLK B8 A10 TDX1
P10.8 P33.15 P11.12 / RXCLKA P11.2 / TXD1
RDX0 B9 E9 TDX2
R233 P11.10 / RXD0A P11.1 / TXD2
P13.0 B12 U11 P34.1 RDX1 A9 E10 TDX3
S201 47K P13.0 P34.1 P11.9 / RXD1A P11.0 / TXD3
HWCFG4 R232 P10.5 P13.1 A12 T12 P34.2 RDX2 E7 D9 TCTL

1
P13.1 P34.2 P11.8 / RXD2A P11.6 / TCTL
8 1 1K5 P13.2 B11 U12 P34.3 RDX3 E8 VFLEX +3V3
P13.2 P34.3 P11.7 / RXD3A L201 R211
7 2 V_UC P13.3 A11 T13 P34.4 RCTL A8 D5
P13.3 P34.4 P11.11 / RCTLA VFLEX
6 3 U13 P34.5 CB203 BLM18BB100SN1D 0R
P34.5
5 4 TC3X7 CB208 CB209
R235 GND GND
D TC3X7 100n 100n D
HWCFG5 R234 47K P10.6 GETH.. 100n
DIPSW-4 GETH..
GND 1K5 GND
V_UC

NOTE: S201 is for device configuration TriBoard TC3X7 Clock, Config, Debug, Ports, ADC
(about configuration see the manual of assembled device) R237
4K7 Sheet: 2 of 7 Infineon Technologies AG
Switch ON means the corresponding signal is low. HWCFG3 R236 P14.3 ATV MC ACE ATV CES
Switch OFF means the corresponding signal is high. 1K5 Number: Am Campeon 1-12
Revision: 2.01 D-85579 Neubiberg
Date: 10.11.2017 Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard AURIX 2G\TriBoard TC3X7\TriBoard TC3X7 V2.X\Clk_Cfg_Dbg_Ports_Adc.sch
1 2 3 4 5 6 7 8

V2.3
2019-09
 1 2 3 4 5 6 7 8

Figure 7-3
PORT[00..34] V_UC

User Manual
PORT[00..34]
V_UC V_UC
R306
CB301 V_CO 0R
U301

P33.4
P33.5
P33.6
P33.7
P20.11
P20.12
P20.13
P20.14
R346 R347 GND R308
3 5
R391 R392 R393 R394 R395 R396 R397 R398 2K 2K R301 100n VCC VIO
V_UC U305 P20.7 4 7 X301
470R 470R 470R 470R 470R 470R 470R 470R R348 RXD CANH R307 0R
4 P15.4 0R
VCC R302 120R R309 1 2
1 0R P20.8 1 6
A SCL TXD CANL 3 4 A
CB309 3 0R 2 8 0R
SDA R349 R303 GND STB 5 6
100n 2 P15.5 P14.1
VSS 7 8

LB T673
LB T673
LB T673
LB T673
LB T673
LB T673
LB T673
LB T673
V_STBY V_UC 0R 0R_opt TLE9251VSJ
9 10

D302
D303
D304
D305
D306
D307
D308
D309
R390 R399 GND 24AA02E48-E/OT P14.0 R304
R305 CAN0
0R 0R 0R_opt
Schematic and Layout

VIN D301 0R
1 U306
3 7 5 GND V_UC GND
VS GND GND
2 V_UC
C303 CB310 R363
VIN
BAT54-04 22μF/50V 100n R361 R316
8 3 10K CB302 V_CO
INH WK 0R
10K U302
R364 GND R318
X305 GND GND 1 P15.1 3 5
RXD VCC VIO
TriBoard Manual TC3X7

R360 4 P23.0 R311 100n 4 7 X302

1 2 GND 1K TXD 0R RXD CANH R317 0R
6 V_UC 0R
3 4 BUS R362 R365 R312 120R R319 1 2
2 P15.0 P23.1 1 6
GND 5 6 R359 C304 EN TXD CANL 3 4
0R 0R 0R 2 8 0R
7 8 VIN 1n R313 GND STB 5 6
0R_opt TLE7259-3GE P00.1
9 10 7 8
0R_opt TLE9251VSJ
R314 9 10
LIN1 GND P00.0
R315 CAN1
0R_opt
0R
GETH..
GETH..
GND GND

P02.1 R325

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

0R_opt

RXCLK
RCTL
RDX3
RDX2
RDX1
RDX0
TXCLK
TCTL
TDX3
TDX2
TDX1
TDX0
REFCLK
B P02.4 R326 B

Schematic - On Board Peripherals

0R_opt

22R
22R
P02.0 R327
RN302
22R 0R_opt
V_UC
P14.10 R320

R373
R374
R371 0R R338
P14.9 R321 4K7 U303 X303
22R_opt T301
0R TXDA 4 15 BPA 1 2
TXD BP 1 2
+3V3 C320 TXENA 5 14 BMA 4 3
R322 TXDEN BM 3 4
P14.8 RXDA 6

7-4
GND RXD B82789-C0104 GND 5 6
0R BGEA 7 VIN
R3100 R3101 R3102 R3103 R3104 R3105 opt BGE R335 R336 7 8
ENA 11 V_CO
R323 VBAT 51R 51R 9 10
P32.3 V_UC 16 V_UC
4K7 opt opt 4K7 opt opt R330 VDD
+3V3 +3V3 0R 2 3 ERAY-A
EN VIO

22R
R337
R370 R328 R331 4K7 0R
P10.2 8

22R
22R R378 R379 STBN
0R_opt 4K7 13
4K7 1K5 GND GND
C301

R372
R377 P15.8 P32.2 R324 ERRNA 10 1 INHA 10nF

RN301
ERRN INH
9 12
100n
100n
100n

R375 330R_opt 0R RXEN WAKE

P12.1 GND
CB303
CB304
CB305

R3106 R3107 R3108 R3109 R3110 R3111 R329 R332

0R P10.1 TLE9221SX
R376 P12.0 opt R333 R334 GND GND GND
opt 4K7 4K7 opt 4K7 4K7 0R_opt opt opt
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

R310 0R
C GND C
GND C319 GND GND

27
26
22
23
24
25
20
19
15
16
17
18
31
14
13
35
22R
X306
2 opt U307
2
3 RTL8211F V_UC
3 R340

TXC

RXC
MDC

TXD3
TXD2
TXD1
TXD0
GND P14.5

RXD3
RXD2
RXD1
RXD0
MDIO

TXCTL

RXCTL
4 MDI0_P 1 C310 0R
4 MDIP0

CLKOUT
5 MDI0_N 2 R358

1
5 MDIN0 GND R341 4K7

INTB / PMEB
MDI1_P 4 RTL8211F 27pF P14.6 U304 T302 X304
MDIP1 Y301
6 MDI1_N 5 36 C311 0R TXDB 4 15 BPB 1 2
6 MDIN1 XTAL_IN TXD BP 1 2
7 MDI2_P 6 37 TXENB 5 14 BMB 4 3

3
7 MDIP2 XTAL_OUT GND R342 TXDEN BM 3 4
MDI2_N 7 NX3225SA-25MHz 27pF P14.7 RXDB 6
MDIN2 RXD B82789-C0104 GND 5 6
8 MDI3_P 9 +3V3 0R BGEB 7 VIN
8 MDIP3 R386 BGE R355 R356 7 8
9 MDI3_N 10 12 RSTN ENB 11 V_CO
9 MDIN3 PHYRSTB VBAT 51R 51R 9 10
C317 +3V3 4K7 V_UC 16 V_UC
R385 R380 R343 R350 VDD
1 Q301B P20.10 2 3 ERAY-B

3
C GND 10K EN VIO R357
10n 4K7 32 39 BSD235N 0R 4K7
LED0 RSET R351 0R
LYA 33 5 8
LYA LED1 R382 STBN
LYKR388 34 HS Q301A 13

DVDD10
AVDD10
AVDD10
AVDD10
REG_OUT / LDO_OUT
AVDD33
AVDD33
DVDD_RG
DVDD33
LYK GND LED2 EPAD 2K49/1% 4K7 GND GND
BSD235N C302

4
510R R389 R344
LGK 2 P20.9 ERRNB 10 1 INHB 10nF

8
3
LGK ERRN INH

21
38
30
40
11
28
29
LGA GND GND GND 9 12
100n
100n
100n

LGA +3V3 510R 0R RXEN WAKE

GND
CB306
CB307
CB308

1
10 R352 TLE9221SX
SC C308 R381 opt R353
S GND /ESR0 R354 GND GND GND
SHIELD 100p /ESR0 opt opt
10K
RJ45 GND
GND GND GND
D Shield D
L301
+1V 2,2μH/1A +3V3

C316 C315 C314 C313 C312 R384 C307 C306 R383 CB311 CB312 CB313 CB314 C305 CB315 CB316 CB317 CB318 C309 CB319 C318
TriBoard TC3X7 On Board Peripherals
100n 100n 100n 100n 1000pF/2KV 4K7 100p 100p 4K7 100n 100n 100n 100n 4,7μF 100n 100n 100n 100n 4,7μF 100n 4,7μF
Sheet: 3 of 7 Infineon Technologies AG
ATV MC ACE ATV CES
GND GND GND GND GND GND GND Number: Am Campeon 1-12
Revision: 2.01 D-85579 Neubiberg
Date: 10.11.2017 Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard AURIX 2G\TriBoard TC3X7\TriBoard TC3X7 V2.X\Peripherals.sch
1 2 3 4 5 6 7 8

V2.3
2019-09
 1 2 3 4 5 6 7 8

VDD_FT VDD_FT
L401 L402 VDD_FT VDD_FT V_UC V_UC

Figure 7-4

User Manual
MMZ1608R300A C402 C403 MMZ1608R300A
CB405 VDD_FT CB413
4u7/6V 100n 4u7/6V D402 R410 R415 R409
CB412 CB402 100n 10K 10K 10K FOR USING WIGGLER WITH JTAG:
100n 100n VDD_FT LP T67K V_UC Assemble R447-R451
GND GND CB411 CB403 GND GND Remove R455-R456

2
5
100n 100n R412 U403
CB410 CB404 R411 680R ADBUS4 1 6 3 4 1 20 CB407
GND GND 100R G VCC
U405 100n 100n 19 10 100n
G GND
VDD_USB TLE4274GSV33 VDD_FT CB409 Q401A Q401B DEBUG..
A +1V8 D401 DEBUG.. A
1 3 100n BSD235N BSD235N GND
IN OUT R450 LB T673 ADBUS0 2 18 DAP0_A DAP0_A

12
37
64
9
4
20
31
42
56
C401 GND 1A1 1Y1
CB401 U401 ADBUS1 4 16 TDI R447 P21.6 P21.6

GND
10μ/6V 1K_opt 1A2 1Y2
100n ADBUS3 6 14 TMS R448 0R_opt DAP1_A
1A3 1Y3
16 ADBUS0 ADBUS6 8 12 USR0 R449 0R_opt /TRST

2
C406
Schematic and Layout

ADBUS0 1A4 1Y4

VPLL
GND GND 49 17 ADBUS1 ACBUS0 11 9 /TRST_J 0R_opt

VPHY
GND VREGOUT ADBUS1 2A1 2Y1

VCCIO
VCCIO
VCCIO
VCCIO

VCORE
VCORE
VCORE
18 ADBUS2 ACBUS1 13 7 /RESET D403
3,3uF ADBUS2 2A2 2Y2
GND 19 ADBUS3 15 5 3 1 /PORST
ADBUS3 2A3 2Y3
50 21 ADBUS4 ACBUS5 17 3 USR8
VDD_FT VREGIN ADBUS4 2A4 2Y4 BAT54
22 ADBUS5
ADBUS5 R454
BU401 23 ADBUS6 VDD_FT SN74AHC244PW DAP1_A
R402 ADBUS6 R413 R421 R422
1 7 24 ADBUS7 5K1
VBUS DM ADBUS7 opt opt
2 27R 10K
D-
TriBoard Manual TC3X7

3 26 ACBUS0 R443 U404 VDD_FT

D+ R403 ACBUS0
4 8 27 ACBUS1 10K ACBUS4 1 5 GND GND
ID DP ACBUS1 /OE VCC
5 27R 28 ACBUS2 2
GND GND ACBUS2 A CB408
29 ACBUS3
R404 ACBUS3 100n
Micro USB 6 30 ACBUS4 4 3
GND REF ACBUS4 Y GND
12K/1% 32 ACBUS5
ACBUS5
C404 33 ACBUS6 ADBUS1 SN74LVC1G125 GND VDD_FT V_UC
ACBUS6
2 34 ACBUS7 ADBUS2 U406

1
OSCI ACBUS7 CB414 CB415
8pF ACBUS5 1 6
Y401 GND VCCA VCCB GND
C405 ACBUS3
NX3225SA-12MHz 3 38 BDBUS0 ACBUS7 ADBUS2 100n 3 4 100n

3
OSCO BDBUS0 A B
8pF 39 BDBUS1 ACBUS2 R455 DAP1_A
BDBUS1
GND VDD_FT 40 ACBUS6 ACBUS5 5 2 0R
R401 BDBUS2 DIR GND

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

14 41
RESET BDBUS3 R444 R451
1K 43 VDD_FT V_UC SN74LVC1T45DBV GND P21.7 P21.7
B BDBUS4 4K7 B
VDD_FT 44 0R_opt
R441 BDBUS5
63 45 V_UC VDD_FT V_UC
EECS BDBUS6 R416 R417
10K 62 46 GND CB416 U407 CB417
EECLK BDBUS7 10K 10K
61 1 6

2
5
R442 EEDATA R420 GND VCCA VCCB GND
48
BCBUS0 4K7 100n
10K 52 BDBUS0 1 6 3 4 ACBUS3 100n 3 4
BCBUS1 A B R456
13 53 P21.7 P21.7
R405 GND TEST BCBUS2 R437 R440
VDD_FT 54 Q402A Q402B ACBUS7 5 2 0R
BCBUS3 0R 0R_opt DIR GND
10K 55 BSD235N BSD235N
BCBUS4 R445 R423
U402 36 57 VDD_FT V_UC SN74LVC1T45DBV GND P20.0 P20.0
CB406 SUSPEND BCBUS5 R414 R418 R419 4K7
8 1 58 0R_opt
100n VCC CS BCBUS6
5 2 60 59 VDD_FT V_UC V_UC

2
5
GND CLK PWREN BCBUS7 4K7 10K 10K
3 GND CB418 U408 CB419

GND
GND
GND
GND
GND
GND
GND
GND
AGND

7-5
D
GND 7 BDBUS1 1 6 3 4 1 6
DNC GND VCCA VCCB GND R431
4 6 VDD_FT FT2232HL

1
5
Q ORG R407 100n 100K

11
15
25
35
47
51
10
Q403A Q403B ACBUS2 100n 3 4 USR1
A B
93LC46B-I/SN opt BSD235N BSD235N
ACBUS6 5 2 R427 P20.1 P20.1
R406 R436 R438 DIR GND
GND 0R_opt
0R 0R_opt R446 SN74LVC1T45DBV GND
2K2 4K7 R428 P20.2 P20.2
0R_opt

Schematic - miniWiggler JDS and Debug connectors

GND

P14.0
P15.2
P14.1
P15.3
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

C C
V_STBY

P20.0
P21.7
P21.6
P20.1
P20.2
P21.6
P20.2
P33.6
P33.7
P21.6
P21.7
P32.6

X406
R424 R425 R426 R429 R430 2 1 R457
0R_opt 0R_opt 0R_opt 0R 0R_opt DAP1 VREF
V_UC X401 4 3 0R X405 V_UC
DAP0 GND
2 1 DAP1_A 6 5 AGBT_TX0_P
VCC TMS USER0 GND 1 2
4 3 8 7 AGBT_TX0_N DAP0_A DAP0_A
GND GND TDO USER1 KEY 3 4
6 5 10 9 DAP1_A DAP1_A
GND CPUCLOCK RESET GND GND 5 6
/DBG_PORST 8 7 P21.6
PORST TDI 7 8
/BRKOUT 10 9 /TRST DAP_SCR GND P21.7
BRKOUT TRST 9 10
12 11 DAP0_A V_UC /TRST /TRST
GND GND TCK GND 11 12
14 13 /BRKIN X402 C_P C407 AGBT_CLK_P
OCDSE BRKIN R452 13 14
16 15 DAP1 2 1 C_N 100n
KEY N.C. DAP1 VREF 15 16
DAP0 4 3 0R C408 AGBT_CLK_N
DAP0 GND GND 17 18
OCDS1 DAP2 6 5 100n
USER0 GND 19 20
DAP3_USR1 8 7 P32.6
L

USER1 KEY 21 22
/DBG_PORST /DBG_PORST 10 9 AGBT_ERR
RESET GND
AGBT_opt
DAP0_A DAP GND
V_UC GND
X404 X403
DAP0_A 2 1 DAPE1 2 1 R453
R439 TCK / DAP0 GND GND DAP1 VREF
P21.7 4 3 /TRST DAPE0 4 3
AGBT_TX0_P
AGBT_TX0_N

TDO / DAP2 /TRST DAP0 GND 0R

P21.6 22R_opt
6 5 DAP1_A DAPE2 6 5
/DBG_PORST

TDI / - TMS / DAP1 USER0 GND

8 7 8 7
V_UC VDDsense BRKIO USER1 KEY
/DBG_PORST 10 9 /ESR0 /DBG_PORST 10 9
/PORST ESR0 /ESR0 RESET GND
ETK_CON_opt DAPE GND R408
R433 /PORST
D P20.1 0R D
0R_opt
PORT[00..51]
PORT[00..51]
/DBG_PORST
TriBoard TC3X7 miniWiggler and Debug connectors
Sheet: 4 of 8 Infineon Technologies AG
ATV MC ACE ATV CES
Number: Am Campeon 1-12
Revision: 2.01 D-85579 Neubiberg
Date: 10.11.2017 Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard AURIX 2G\TriBoard TC3X7\TriBoard TC3X7 V2.X\Wiggler_Dbg_con.sch
1 2 3 4 5 6 7 8

V2.3
2019-09
 1 2 3 4 5 6 7 8

Figure 7-5

User Manual
V_STBY
C507
GND
1μF/10V U501 U502

5
X501 VCC_IN D502 VIN D501 TLF35584QVVS1/2 V_PREREG TLS205B0EJV33 +3V3
A L501 L502 A
1 2 43 8 1
VST SW1 IN Q
XAL5050-223MEB MSS2P2 42 XAL4030-472MEC 2

QST
SS26 SW2 SENSE/ADJ C505
45 C503 V_UC

POWER
C502

2
C501 VS1 C504 10μF
44 41 22μF/10V 5
47μF/40V GND VS2 PG1 EN 10nF
GND VDD_USB D503 40 4

GND
GND
Schematic and Layout

CB501 PG2 CB502 BYP

100μF/40V GND GND
GND Q501 100n 25 34 100n

6
STU FB1

1,2,5,6
SS22_opt

HS
BSL606SN 35
FB2
3 46 36
DRG FB3
37 GND
FB4
47 38

4
RSH FB5
48
RSL
1 19
R501 BSG SYN
TriBoard Manual TC3X7

21
EVC
250mR 26 +3V3 +3V3 V_UC
VCI
/PORST GND 17 23
ROT SEC GND
/ESR1 18 V_UC R511 R512 R513
INT 620R 680R 1K5
30 C508
QUC GND
P14.2 15
SCS D505 D506 D507
P15.3 14 V_CO 4,7μF/10V
SCL LP T67K LP T67K LP T67K
P15.6 12 31 C509

3
SDI QCO GND Q504

Schematic - Power Supply

P15.7 13 +1V25
SDO R510
V_VR 4,7μF/10V 1 GND GND
P14.3 16 29 C510 82K
WDI QVR GND
BC848CGND

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

P33.8 20 QT1 4,7μF/10V
ERR
P33.9 R503 11 33 C511
B SS1 QT1 GND B
1K 10 VDD +1V25
SS2 4,7μF/10V R523
D508 QT2
R504 32 C512 VDDSB
QT2 GND 0R
470R 24 V_STBY CB515 CB516
LP T67K FRE 4,7μF/10V R522
GND 3
ENA GND
V_STBY 4 22 0R
R507 WAK TM R520 100n 100n
27 V_CO CB510

GND
AG1
AG2
AG3
AG4
AG5
AGS
GST 0R
VCC_IN 100K CB517
GND
GND

3
6
7
8
9
R508

28
39
Q505 100n

HS
X502 1
2 1BSS138N 0R V_UC 100n

PORT[00..34]
GND R521
3 VDDSB GND CB518
4 R502 R509

7-6
10K 20K 0R
EmW_Pwr_opt CB512
GND 100n
P33.10 GND CB513 CB519
100n
GND
S502 100n 100n
VIN GND
PORT[00..34] R505 V_UC +3V3
ENA 10K R506
100K R524 R525 VDDP3

3
S501 0R_opt 0R_opt
V_UC
GND R531 1 Q502 R533
BC848C 0R
RESET
A19
B18
W20
V19
B3
A2
T11
G8
H7
P13
P8
N14
N7
H14
G13
E15
D16

4K7 R532 C515 C519 CB520 U201A

Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

2
10K 4μ7/10V 2,2μF 100n B2 TC3X7
C VSS C
D4
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD

V_UC GND GND E5

VEXT
VEXT
VEXT
VEXT

VSS
VDDP3
VDDP3

GND GND GND T16

VEVRSB

VSS

/PORST
U17
R534 VSS
W19
VDD / VDDSB
VDD / VDDSB

2K2 VSS
/PORST /PORST /PORST G17 Y20
/PORST PORST VSS
A20
VSS
V_UC /ESR1 /ESR1 G16 B19
ESR1 VSS
POWER D17
VSS
/ESR0 /ESR0 F16 E16
R535 ESR0 VSS
G12
4K7 VSS
/ESR1 Q506 VGATE1N G9

2
/ESR1 VSS
+1V25 BSZ15DC02KD H12
L503 VSS
V_UC V_UC 8 1 Y17 H11
GND P32.0 / VGATE1N VSS
LTF5022T-3R3N2R5 7 H10
C522 C521 C518 VSS
6 W17 H9

2
V_UC C520
R536 10μF 22μF 1μF_opt P32.1 / VGATE1P VSS
5 4 J14
4K7 R537 Q503 GND VSS
/ESR0 1 J13
/ESR0 BC858C 10μF VSS
GND GND VGATE1P

3
10K
D504 GND

3
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS

R538 V_PREREG C506

GND
120R GND
J7
J8

P9

LS T67K
L8
L9

N9
K8
K9

M7
M8
J10
J11

10
9
P12
L10
L11
L12
L13

N10
N11
N12
K10
K11
K12
K13

M10
M11
M13
M14

10μF_opt V_UC
7
VCC
VS
VS

GND
1 CB506
SW 100n_opt
D 2 6 D
SW PWM
5
LSCON
GND

U503
PGND
PGND
GND
GND

TLF11251_opt TriBoard TC3X7 Power supply

Infineon Technologies AG
8
3
4

Sheet: 5 of 7
HS

ATV MC ACE ATV CES

Number: Am Campeon 1-12
GND Revision: 2.01 D-85579 Neubiberg
Date: 10.11.2017 Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard AURIX 2G\TriBoard TC3X7\TriBoard TC3X7 V2.X\Supply.sch
1 2 3 4 5 6 7 8

V2.3
2019-09
 1 2 3 4 5 6 7 8

NC1[5..80]
NC1[5..80]
NC2[5..80]
NC2[5..80]

Figure 7-6

User Manual
X601 GND X602 GND TOP
PLUG PLUG
1 2 1 2
VCC_IN VCC_IN
3 4 3 4
NC1.5 P21.6
5 6 5 6
NC1.7 P21.7
7 8 7 8
NC1.9 NC1.10 P22.4 P22.8
9 10 9 10
NC1.11 NC1.12 P22.5 P22.9
A 11 12 11 12 A
NC1.13 NC1.14 P22.6 P22.10
13 14 13 14
NC1.15 NC1.16 /ESR1 /ESR0
15 16 /ESR1 15 16 /ESR0
NC1.17 NC1.18 P22.7 P22.11
17 18 17 18
NC1.19 NC1.20
19 20 GND 19 20 GND
NC1.21 NC1.22 NC2.21 /PORST
Schematic and Layout

21 22 21 22 /PORST
NC1.23 NC1.24 P10.5 P23.3
23 24 23 24
NC1.25 NC1.26 P10.4 P23.4
25 26 25 26
NC1.27 NC1.28 P10.2 P23.1
27 28 27 28
NC1.29 NC1.30 P13.1 P22.1
29 30 29 30
NC1.31 NC1.32 P13.0 P22.0
31 32 31 32
NC1.33 NC1.34 P13.3 P22.3
33 34 33 34
NC1.35 NC1.36 P13.2 P22.2
35 36 35 36
NC1.37 NC1.38 P20.9 P20.10
37 38 37 38
TriBoard Manual TC3X7

NC1.39 NC1.40 XTAL[1..2] P20.13 P00.4 PERIPHERALS

39 40 XTAL[1..2] 39 40
NC1.41 NC1.42 P33.5 P20.6
41 42 41 42
NC1.43 NC1.44 P20.3 P20.2
43 44 43 44
NC1.45 NC1.46 P00.0 P00.3
45 46 45 46
NC1.47 NC1.48 P00.1 P00.2
47 48 47 48
NC1.49 P21.2
49 50 GND 49 50 GND
NC1.51 P21.3 XTAL1 P32.4
51 52 51 52
NC1.53 P21.4 XTAL2 NC2.54
53 54 53 54
NC1.55 P21.5 P15.3 P15.5
55 56 55 56
NC1.57 NC1.58 P15.2 P15.4
57 58 57 58
NC1.59 NC1.60 P14.1 P15.1
59 60 59 60
NC1.61 NC1.62 P14.0 P15.0
61 62 61 62
NC1.63 NC1.64 P20.11 P00.12
63 64 63 64

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

NC1.65 NC1.66 P20.14 P00.11

Schematic - Connectors (Plug)

65 66 65 66
NC1.67 NC1.68 P20.12 P00.5
B 67 68 67 68 B
NC1.69 NC1.70 P20.7 P20.8
69 70 69 70
NC1.71 P20.0 P15.8 P10.8
71 72 71 72
NC1.73 NC1.74 P10.7 P10.3
73 74 73 74
NC1.75 NC1.76
75 76 VDDSB 75 76 GND
NC1.77 NC1.78
77 78 77 78
P21.0 P21.1
79 80 V_UC 79 80 +3V3
FTSH-140-02-L-DV-ES-A FTSH-140-02-L-DV-ES-A

NC4[5..80]

7-7
NC4[5..80]
AN[0..47]
AN[0..47]

X603 GND X604 GND

PLUG PLUG
1 2 1 2
3 4 3 4
AN0 AN16 P00.9 P11.14
5 6 5 6
AN1 AN17 P00.10 P11.15
7 8 7 8
AN2 AN18 P02.0 NC4.10
9 10 9 10
AN3 AN19 P02.1 NC4.12
11 12 11 12
AN4 AN20 P02.2 NC4.14
13 14 13 14
AN5 AN21 P02.3 NC4.16
15 16 15 16
AN6 AN22 P02.4 P14.7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

17 18 17 18
C AN7 AN23 P02.5 P14.8 C
19 20 19 20
AN8 AN24 P02.9 P14.9
21 22 21 22
AN9 AN25 P02.10 P14.10
23 24 23 24
AN10 AN26 P02.11 P15.6
25 26 25 26
AN11 AN27 P01.3 P15.7
27 28 27 28
AN12 AN28 P01.4 P20.1
ADC 29 30 29 30
AN13 AN29 P10.0 P01.5
31 32 31 32 PORTS
AN14 AN30 P10.1 P01.6
33 34 33 34
AN15 AN31 P10.6 P23.0
35 36 35 36
P12.0 P23.2
GND 37 38 GND 37 38
P12.1 P23.5
VDDM 39 40 VAREF1 39 40
NC4.41 P23.6
GND 41 42 VAREF2 41 42
NC4.43 P23.7
GND 43 44 GND 43 44
AN32 AN40 NC4.45 NC4.46
45 46 45 46
AN33 AN41 NC4.47 NC4.48
47 48 47 48
AN34 AN42 NC4.49 P32.2
49 50 49 50
AN35 AN43 NC4.51 P32.3
51 52 51 52
AN36 AN44 NC4.53 P32.5
53 54 53 54
AN37 AN45 NC4.55 P33.8
55 56 55 56
AN38 AN46 NC4.57 P33.9
57 58 57 58
AN39 AN47 NC4.59 P33.10
59 60 59 60
NC4.61 P33.13
GND 61 62 GND 61 62
P33.3 P33.6 NC4.63 P33.14
63 64 63 64
P33.2 P33.0 NC4.65 P33.15
65 66 65 66
P33.1 P33.4 P11.13 P32.6
67 68 67 68
P34.1 P32.7
V_UC 69 70 +3V3 69 70
P02.6 P00.6 P34.2 P34.4
71 72 71 72
P02.7 P00.7 P34.3 P34.5
73 74 73 74
D P02.8 P00.8 P01.7 D
75 76 VFLEX 75 76
P33.7 P14.3
77 78 77 78
P33.11 P33.12
79 80 V_UC 79 80 +3V3
FTSH-140-02-L-DV-ES-A FTSH-140-02-L-DV-ES-A
TriBoard TC3X7 Connectors plug
Sheet: 6 of 7 Infineon Technologies AG
PORT[00..34] ATV MC ACE ATV CES
PORT[00..34]
Number: Am Campeon 1-12
Revision: 2.01 D-85579 Neubiberg
Date: 10.11.2017 Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard AURIX 2G\TriBoard TC3X7\TriBoard TC3X7 V2.X\Connectm.sch
1 2 3 4 5 6 7 8

V2.3
2019-09
 1 2 3 4 5 6 7 8

NC1[5..80]
NC1[5..80]
NC2[5..80]
NC2[5..80]

Figure 7-7

User Manual
X701 GND X702 GND BOTTOM
SOCKET SOCKET
1 2 1 2
VCC_IN VCC_IN
3 4 3 4
NC1.5 P21.6
5 6 5 6
NC1.7 P21.7
7 8 7 8
NC1.9 NC1.10 P22.4 P22.8
9 10 9 10
NC1.11 NC1.12 P22.5 P22.9
A 11 12 11 12 A
NC1.13 NC1.14 P22.6 P22.10
13 14 13 14
NC1.15 NC1.16 /ESR1 /ESR0
15 16 /ESR1 15 16 /ESR0
NC1.17 NC1.18 P22.7 P22.11
17 18 17 18
NC1.19 NC1.20
19 20 GND 19 20 GND
NC1.21 NC1.22 NC2.21 /PORST
Schematic and Layout

21 22 21 22 /PORST
NC1.23 NC1.24 P10.5 P23.3
23 24 23 24
NC1.25 NC1.26 P10.4 P23.4
25 26 25 26
NC1.27 NC1.28 P10.2 P23.1
27 28 27 28
NC1.29 NC1.30 P13.1 P22.1
29 30 29 30
NC1.31 NC1.32 P13.0 P22.0
31 32 31 32
NC1.33 NC1.34 P13.3 P22.3
33 34 33 34
NC1.35 NC1.36 P13.2 P22.2
35 36 35 36
NC1.37 NC1.38 P20.9 P20.10
37 38 37 38
TriBoard Manual TC3X7

NC1.39 NC1.40 XTAL[1..2] P20.13 P00.4 PERIPHERALS

39 40 XTAL[1..2] 39 40
NC1.41 NC1.42 P33.5 P20.6
41 42 41 42
NC1.43 NC1.44 P20.3 P20.2
43 44 43 44
NC1.45 NC1.46 P00.0 P00.3
45 46 45 46
NC1.47 NC1.48 P00.1 P00.2
47 48 47 48
NC1.49 P21.2
49 50 GND 49 50 GND
NC1.51 P21.3 XTAL1 P32.4
51 52 51 52
NC1.53 P21.4 XTAL2 NC2.54
53 54 53 54
NC1.55 P21.5 P15.3 P15.5
55 56 55 56
NC1.57 NC1.58 P15.2 P15.4
57 58 57 58
NC1.59 NC1.60 P14.1 P15.1
59 60 59 60
NC1.61 NC1.62 P14.0 P15.0
61 62 61 62
NC1.63 NC1.64 P20.11 P00.12
63 64 63 64

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

NC1.65 NC1.66 P20.14 P00.11
65 66 65 66
NC1.67 NC1.68 P20.12 P00.5
B 67 68 67 68 B
NC1.69 NC1.70 P20.7 P20.8
69 70 69 70
NC1.71 P20.0 P15.8 P10.8

Schematic - Connectors (Socket)

71 72 71 72
NC1.73 NC1.74 P10.7 P10.3
73 74 73 74
NC1.75 NC1.76
75 76 VDDSB 75 76 GND
NC1.77 NC1.78
77 78 77 78
P21.0 P21.1
79 80 V_UC 79 80 +3V3
FLE-140-01-G-DV-A FLE-140-01-G-DV-A

NC4[5..80]

7-8
NC4[5..80]
AN[0..47]
AN[0..47]

X703 GND X704 GND

SOCKET SOCKET
1 2 1 2
3 4 3 4
AN0 AN16 P00.9 P11.14
5 6 5 6
AN1 AN17 P00.10 P11.15
7 8 7 8
AN2 AN18 P02.0 NC4.10
9 10 9 10
AN3 AN19 P02.1 NC4.12
11 12 11 12
AN4 AN20 P02.2 NC4.14
13 14 13 14
AN5 AN21 P02.3 NC4.16
15 16 15 16
AN6 AN22 P02.4 P14.7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

17 18 17 18
C AN7 AN23 P02.5 P14.8 C
19 20 19 20
AN8 AN24 P02.9 P14.9
21 22 21 22
AN9 AN25 P02.10 P14.10
23 24 23 24
AN10 AN26 P02.11 P15.6
25 26 25 26
AN11 AN27 P01.3 P15.7
27 28 27 28
AN12 AN28 P01.4 P20.1
ADC 29 30 29 30
AN13 AN29 P10.0 P01.5
31 32 31 32 PORTS
AN14 AN30 P10.1 P01.6
33 34 33 34
AN15 AN31 P10.6 P23.0
35 36 35 36
P12.0 P23.2
GND 37 38 GND 37 38
P12.1 P23.5
VDDM 39 40 VAREF1 39 40
NC4.41 P23.6
GND 41 42 VAREF2 41 42
NC4.43 P23.7
GND 43 44 GND 43 44
AN32 AN40 NC4.45 NC4.46
45 46 45 46
AN33 AN41 NC4.47 NC4.48
47 48 47 48
AN34 AN42 NC4.49 P32.2
49 50 49 50
AN35 AN43 NC4.51 P32.3
51 52 51 52
AN36 AN44 NC4.53 P32.5
53 54 53 54
AN37 AN45 NC4.55 P33.8
55 56 55 56
AN38 AN46 NC4.57 P33.9
57 58 57 58
AN39 AN47 NC4.59 P33.10
59 60 59 60
NC4.61 P33.13
GND 61 62 GND 61 62
P33.3 P33.6 NC4.63 P33.14
63 64 63 64
P33.2 P33.0 NC4.65 P33.15
65 66 65 66
P33.1 P33.4 P11.13 P32.6
67 68 67 68
P34.1 P32.7
V_UC 69 70 +3V3 69 70
P02.6 P00.6 P34.2 P34.4
71 72 71 72
P02.7 P00.7 P34.3 P34.5
73 74 73 74
D P02.8 P00.8 P01.7 D
75 76 VFLEX 75 76
P33.7 P14.3
77 78 77 78
P33.11 P33.12
79 80 V_UC 79 80 +3V3
FLE-140-01-G-DV-A FLE-140-01-G-DV-A
TriBoard TC3X7 Connectors socket
Sheet: 7 of 7 Infineon Technologies AG
PORT[00..34] ATV MC ACE ATV CES
PORT[00..34]
Number: Am Campeon 1-12
Revision: 2.01 D-85579 Neubiberg
Date: 10.11.2017 Tel.: +49-89-234-0
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard AURIX 2G\TriBoard TC3X7\TriBoard TC3X7 V2.X\Connectf.sch
1 2 3 4 5 6 7 8

V2.3
2019-09
 7.3

Figure 7-8

User Manual
X306

X604 X601
Layout
Schematic and Layout

R383
C306
C310 X202
L 301
R390 R399 S202
C3 11 C318 CB319
X4 04

Y301
R256
R38 2
Y401

D302
D303
D304
D305
D306
D307
D308
D309
TriBoard Manual TC3X7

C30 9

CB318
R39 2 R3 93 R39 4 R395 R39 6 R3 97 R39 8
R402 R3 104

R391

U307
R255
R43 9

CB401
R3100 X403
X201

BU401
CB3 17

R3109
R31 01

C320
R3103
R4 03 U401 R386
R310 2
R22 6

Component Plot Top Layer

R3 108

CB405
S201
R377
R380 R379

C402
R22 5

L401
CB408
R3 75

Q301
R240
R376

U404
CB402 CB414

R401

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

CB416
R453

CB418
CB419
U40 7 U40 8

R230
R232
R234
D40 1 D40 2 R24 1

R236
U4 06

R217

R455

T 301
R456

CB417
R446
R41 1

X301

X303
R335
R444

R336
R428
R42 9

R451
CB415
R42 7 U201 R43 0

R454

R337
C301
R21 3 X402

R423
R2 12 R452

7-9
R329
C20 2

X401
R324

R424
R202
R206
R205

CB201
R2 01 R204

T302
Y201

R207

R426
R425
C2 01

X302
R3 54

X304
CB202
R203

R531

R532

R355
R356
R3 44

R357
C302
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

U50 2

S501
C50 5
D504 D50 7

C504
D50 6

C503
C508

C509
C30 3 X502

R508

CB502
R346

L502
D5 08 D50 5
U305

R509 R247
CB309

X305
R348

R36 1
C502 R3 49
C522

D301

R359
U501 R34 7
X406

C5 07 S50 2

R249
R244

CB501
R248
R507
R457

L 501
R501

X501
X603 X602

C501

V2.3
2019-09
 Figure 7-9

User Manual
C316

C315

C314

C317

X7 01 X7 04 R389

R385
C308
Schematic and Layout

R384
C307
C305 CB3 15

R2 60 R258
R388

R3105 C3 12
CB3 12

R378
C31 9

R3110
R310
C313
C4 04
CB412
CB316

R3111
C4 06 CB 413
TriBoard Manual TC3X7

CB3 14
R370 C40 5
CB409

R257
R3106

R259
R3 72

R3107
CB 313
R414 R40 4
CB404
C401

RN301 CB311 L40 2

C403

R525
R41 9 CB411
R44 0

R219
R371

R211
R4 18 R4 42 U405
Q403
CB410

R3 81 R420
CB403

CB209
R416
R43 7 R41 7 Q 402 R4 41
R433 R42 2 R405

R218
R4 49

R231
R254 R2 50 R2 52
R406

Component Plot Bottom Layer

R237
R235
R233
R44 3

L201

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

R44 8
R421

R413

R4 38 U4 02
R410

R25 3 R25 1 U4 03
R4 47
R4 36 Q401
R450

R30 7 CB40 6
R412

CB208
R407

R304
R308
R309
CB407
R373 R415
R40 9 R445
R431

R374
R302

R524
C519
R328
R334

RN302
R303
CB301
R323

U301
R305
CB5 20 CB51 2 D4 03 R327 R330 CB304
CB519 R301 R320
CB20 3 CB305 R333
R306 R321
R408
U303

R522 CB30 3
R326

7-10
R338

R322 R3 32

R31 7 R325 R331

CB517
CB515

R216
R215
R319

R214
R34 3
R318

R31 4

R209
C20 7 R340

CB518
CB206
R31 2

CB516
Q 502 CB3 07
R350

CB5 10 C208
R315

R208
C206 R341

CB513
R3 53
CB 302

R3 13 CB308
CB20 5
U302
U304

R3 42
R311 CB306

C205
C204
C515

R358
R316

R52 0 CB2 04 R53 3

R3 51

C407
R52 1 C40 8 R352
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

Q50 3 R53 6
R513 R538
R523 R362
R36 4
R53 7
R51 0 R512
X405 R2 38 R365 R363
C5 18
C520
R535
Q504

R2 39
C2 03 R51 1 C3 04
U306
C510
C512
C511

U503

CB 506
Q506

R220
R504

D501
R534

C5 06
C521
R360

CB31 0
R2 23
R222

R2 45
R50 3
D503
R502

L503

R505 Q5 01
R506

R221 R246
Q505

X7 02 X70 3
D502

V2.3
2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Schematic and Layout

7.4 Layout with Dimensioning

The following dimensions should be used for development of extension boards.

INFINE O N TE CHNO LO G IE S A G
TriB oard-TC3X 7 (TH) V2.0 (1 )

Figure 7-10 Dimensioning (mm)

User Manual 7-11 V2.3
TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0
Schematic and Layout

INFINE O N TE CHNO LO G IE S A G
TriB oard-TC3X 7 (TH) V 2.0 (1)

Figure 7-11 Dimensioning (mil)

The dimensioning is valid for all TriBoards.

User Manual 7-12 V2.3
TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
TriBoard Manual TC3X7
Hardware: TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0

Revision History
Page or Item Subjects (major changes since previous revision)
V2.3, 2019-09
chapter 3.2.2 add TC3A7 as restricted usable device
chapter 3.8 add hint for eeprom access with TC337 (no I2C module)
chapter 3.9 add hint that CAN1 on TC337 only usable via P00.0 and P00.1
chapter 3.10 add description for LIN master and slave changes
Revision History add complete history of all previous versions
V2.2, 2019-06
all add TC367, TC337, TC327 and TC3E7 as usable (planned) device and adapt description for this
devices. Add some notes for peripheral availability on different devices
chapter 6 add separat connector layout for the different device
chapter 3 add detailed description of usable devices/restricted devices
V2.1, 2018-10
all add TC377 as usable device and adapt description for TC377
V2.0, 2017-11
adapt to new board hardware V2.x from V1.x

User Manual RevisionHistory-1 V2.3

TriBoard TC3X7 TH V2.0(1) and TriBoard TC3X7 V2.0 2019-09
Please read the Important Notice and Warnings at the end of this document

Trademarks of Infineon Technologies AG

µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,
DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™,
HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™,
OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™,
SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™.

Trademarks updated November 2015

Other Trademarks
All referenced product or service names and trademarks are the property of their respective owners.

IMPORTANT NOTICE
Edition 2019-09 The information given in this document shall in no For further information on technology, delivery terms
event be regarded as a guarantee of conditions or and conditions and prices, please contact the nearest
Published by
characteristics ("Beschaffenheitsgarantie"). Infineon Technologies Office (www.infineon.com).
Infineon Technologies AG With respect to any examples, hints or any typical
81726 Munich, Germany values stated herein and/or any information regarding
the application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities WARNINGS
© 2019 Infineon Technologies AG. of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any Due to technical requirements products may contain
All Rights Reserved.
third party. dangerous substances. For information on the types
In addition, any information given in this document is in question please contact your nearest Infineon
Do you have a question about any subject to customer's compliance with its obligations Technologies office.
aspect of this document? stated in this document and any applicable legal
Email: [email protected] requirements, norms and standards concerning Except as otherwise explicitly approved by Infineon
customer's products and any use of the product of Technologies in a written document signed by
Infineon Technologies in customer's applications. authorized representatives of Infineon Technologies,
Document reference Infineon Technologies’ products may not be used in
The data contained in this document is exclusively
Doc_Number any applications where a failure of the product or any
intended for technically trained staff. It is the
responsibility of customer's technical departments to consequences of the use thereof can reasonably be
evaluate the suitability of the product for the intended expected to result in personal injury.
application and the completeness of the product
information given in this document with respect to
such application.