MICHELSON’S INTERFEROMETER

Objectives:

1. Alignment of Michelson’s Interferometer using He-Ne laser to observe concentric

circular fringes
2. Measurement of the wavelength of He-Ne Laser and Na lamp using circular
fringes
3. Study of fringes of equal inclination and equal thickness using Na lamp

Introduction

The instruments based upon the principle of interference are called interferometers.
These are basic optical tools used to precisely measure wavelength, distance, index of
refraction, and temporal coherence of optical beams etc. It is an amplitude-splitting
interferometers devised by Albert Michelson in 1890, the first American physicist to receive
the Nobel Prize (1907 for work in optics). Michelson and Morley used this interferometer in
their celebrated series of experiments designed to demonstrate the existence of the ether. It is
still an important instrument in today's laboratories and it is being widely used as an
instrument for measuring the wavelength of an unknown light source, to measure extremely
small distance and for investigating optical media.

Construction:

Construction of Michelson
interferometer is shown in Fig. 1. It
consists of two highly polished mirrors
M1 and M2. Two glass plates beam
splitter (BS) and compensatory glass
plate (CP), are placed parallel to each
other between the mirrors at an angle of
450. The rear side of glass plate BS is
semi-silvered such that the light from a
source is equally reflected and
Fig. 1 : Construction of Michelson’s Interferometer
E

Last updated in Dec 2017 © NISER Page 1

transmitted by it. In this way division of amplitude takes place. From a broad source, let a
monochromatic light of wavelength λ fall on BS. Half of light falling on BS is reflected
towards the mirror M1 and the other half is transmitted towards mirror M2. Hence BS is
known as a beam splitter. In case of sources which are not monochromatic, the glass plate CP
is inserted between BS and M2. The role of CP is explained further in the following
paragraph. After splitting, the two rays are reflected back by the mirrors M1 and M2 and
return to the plate BS. The ray reflected from M1 is transmitted through BS and the ray
reflected from M2 is reflected again by BS. The two rays coming from the two mirrors
interfere and fringes are observed on a screen (for laser) or by naked eye (Na lamp) at E.
Usually one of the mirrors is mounted on a translation stage so that it can be moved back and
forth to observe the change in fringes.

Optical path

The rays falling on mirrors M1 and M2 are derived from the same source originally incident
on plate BS (see Fig. 1). The wave reflected from M1 and entering the eye crosses BS twice.
However the path of the other wave falling on the mirror M2, in the absence of compensating
plate CP, travels totally in air. Thus an extra optical path 2(μ -1)t is introduced where, 't' is
the thickness of the plate and ‘μ‘ is the refractive index of the BS plate for the
monochromatic light used. Presence of CP is not essential if fringes are produced with
monochromatic light. But it produces a serious problem when white light is used. Thus, it
becomes necessary to compensate for the extra optical path 2(μ -1)t for all wavelengths. This
is done by introducing another glass plate CP of same thickness as that of BS parallel to it.
Thus, the two waves will interfere constructively or destructively as per the following conditions of
path difference, Δ:

Δ = 2nλ/2 = n λ (for maxima, n is an integer)

Δ = (2n+1)λ/2 (for minima, n is an integer)

Types of fringes:

Path difference between the two rays can be varied by moving M1. Mirror M1 and the virtual image of
mirror M2 act as the two surfaces of an air film. The fringes formed in Michelson interferometer may
be circular, curved or straight depending upon the nature of the air film.

Last updated in Dec 2017 © NISER Page 2

Concentric circular fringes (fringes of equal inclination):
Concentric circular fringes are obtained when the air film is parallel as shown in Fig. 2. M2'
is the virtual image of M2 and it is parallel to M1. For simplicity, light source L is at the
observer's position. L1 and L2 are the virtual images of L formed by M1 and M2', and are
coherent. Let d be the distance between M1 and M2', therefore the distance between L1 and L2
is 2d. Let θ be the angle between the incident beam originated at P and the reflected beams
from M1 and M2'. Then path difference between light beams from points P’and P" is 2d cosθ.
A maximum (bright fringe) will be formed when 2dcosθ = nλ . For a fixed value of n, λ and
d, the value of θ is a constant, and the contour of the maximum point becomes a ring. The
centre of the ring is in line with the observer and perpendicular to the mirror plane. Each
circular ring corresponds to a particular value of θ. Hence the fringes are known as fringes of
equal inclination.

L2
P’’ L1
2d P’
θ
2d cos θ P’’ P’ ’ P

Fig. 2: Formation of circular fringes

Curved fringes (fringes of equal thickness):

When M1 and virtual image M2' are inclined to
each other, the film enclosed is wedge shaped.
Then curved fringes can be observed as shown
in Fig. 3. These are also known as fringes of
equal thickness. Fig. 3: Formation of curved fringes
Straight line fringes:
When M1 and virtual image M2' intersect,
straight line fringes are obtained around the
point of intersection (see Fig. 4). The path
Fig. 4: Formation of straight line fringes
Last updated in Dec 2017 © NISER Page 3
difference along the line of intersection is zero and therefore, is same for all the wavelengths.
When a source of white light is used we get central achromatic bright fringe. On either side of
central fringe, few coloured straight fringes are observed.

Determination of λ from circular fringes:

Circular fringes are used to determine the wavelength of the source of light. For a given
separation of ‘d’ between the mirrors M1 and M2 and normal incidence (θ=0), the path
difference is given as 2d = nλ.
If one mirror is moved by a distance Δd and N number of rings appear/disappear at the
center, then the path difference after moving the mirror is given as
2(d+ Δd) = (n+N)λ

Hence, λ = 2(Δd)/N

Experimental set up:

Set up with laser as source Set up with Na lamp as source

Fig. 5

Last updated in Dec 2017 © NISER Page 4

 Fig. 6: Schematics of Michelson Interferometer

Procedure:
(I) Observation of circular fringes using He-Ne laser as the light source
1. Set the Michelson Interferometer on the table with coarse adjustable knob pointing
towards you.
2. Set the lab jack in front of microscopic objective holder and set the height using lifting
knob.
3. Place the He-Ne Laser source on lab jack, pointing the source towards the centre of fixed
mirror.
4. Turn the laser on and adjust the laser beam height using lab jack lifting knob until the
beam is approximately parallel with the top of the interferometer and strikes the mirror at
the centre.
5. Set the viewing screen opposite of the adjustable mirror M2. Note that the viewing screen
should be placed at 1-2meter from the adjustable mirror to get better resolution.
6. To get circular fringes, M1 should be exactly perpendicular to M2. In this position,
Michelson interferometer is said to be in normal adjustment. The setting needs that the
plane of BS exactly bisects the angle (45°) between the two mirrors.
7. Using coarse adjustment knob makes the distance of M1 and M2 from BS nearly equal.
8. When laser beam will be passing through beam splitter (BS) at 45° and observed in the
direction M2, four spots of the He-Ne Laser beam are seen on the viewing screen; two of
which are faint and two are intense as shown in figure. The faint spots are due to reflection
from un-silvered surface of BS and then from M1 and M2 respectively. The intense spots
Last updated in Dec 2017 © NISER Page 5
 are due to reflection from silvered surface of BS and M1, M2. (Note: Two spots of He-Ne
laser beam also been seen on the viewing screen other than four spots, which are ignorable
because these two spots are formed by compensating plate).
9. The tilting screws at the back of M1 and M2 are adjusted to obtain only two images as
shown in fig. This happens only when the mirrors M1 and M2 are exactly perpendicular to
each other.
10. Now place the beam expander and adjust its height to get circular fringes. Make fine
adjustments of mirrors M1 and M2 using top tilting screws to observe clear fringes on the
viewing screen.
(II) Determination of wavelength of He-Ne laser light source
1. Obtain the circular fringes are obtained as already explained.
2. Move the mirror M2 using fine adjustment knob. The fringes appear or disappear in the
field of view. (Always move the knob in one direction for precise measurement.)
3. Note down the reading of coarse adjustment knob. Let it be ‘m’. Multiply this reading with
least count 0.01mm. Note the reading of fine adjustment knob. Let it be ‘n’. Multiply this
reading with least count 0.0001mm. Now add the above two readings of coarse and fine
adjustment knobs. Let it be d1.
5. Rotate the fine adjustment knob to count the number of fringes appearing or disappearing.
Let it be N.
6. Note the observations as already explained in step 3. Let it be d2.
7. Subtract d1 from d2 to get the value of‘d’ for ‘m’ fringes.
8. Use the formula to calculate the value of d.

(III) Observation of circular fringes using He-Ne laser as the light source
1. Perform steps 1-10 from procedure I.
2. Replace the laser with Na lamp and switch it on.
3. Put a ground glass screen in front of the lamp.
4. A fringe pattern should appear on the screen and only fine adjustments of the movable
mirror should be necessary. You can also view the pattern with naked eye or attaching a
telescope near coarse adjustment knob.
(IV) Determination of wavelength of Na lamp

Follow the same procedure as described in (II).

Last updated in Dec 2017 © NISER Page 6

(V) Fringes of equal inclination

Fig. 7
1. Using He-Ne laser as light source reproduce circular fringes similar to Fig. 7(a).
Orientation of M1 and M2' is shown in the bottom panel corresponding to each set
of fringes in Fig.7 (a-e).
2. Adjust the coarse micrometer such that images (a) to (e) are viewed in succession.
3. Set the fine micrometer to the middle of the scale.
4. Readjust the coarse micrometer as close as possible to image Fig. 7(c).
5. Use the fine micrometer to produce fringes of equal inclination.
6. Take pictures of the fringes in a similar way shown in Fig. 7.

(VI) Fringes of equal thickness

Fig.7
1. Using He-Ne laser as light source turn the fine micrometer to move the movable mirror in
a direction such that only few interference circular fringes are visible.
2. Adjust the movable mirror a little such that M1 and M2' till you see curved fringes as
shown in Fig. 7(f). Orientation of M1 and M2' is shown in the bottom panel corresponding

Last updated in Dec 2017 © NISER Page 7

 to each set of fringes in Fig.7 (f-j).
3. Continue to turn the fine micrometer to make the curved fringes move toward their centre.
Some straight fringes can be observed (if done very carefully) in succession as shown in
Fig. 7 (h), when M1 and M2' will intersect each other.
4. Take pictures of the fringes in a similar way shown in Fig, 7 (f-j).

Observations: (For He-Ne laser/ Na lamp)

Initial position of gauge (݀ଵ ) = __________ mm

Sl. No.. N m n ݀ଶ Δd = (݀ଶି ݀ଵ)

(mm) (mm)

Graph:

Plot Δd vs. N and determine λ from slope.

Results and Discussions

λ for He-Ne laser =

λ for Na lamp =

Literature values: λ for He-Ne laser = 632.8 nm

λ for Na lamp = 589.3 nm

Precautions:
1. When turning the fine adjustment knob to count fringes, always turn it one complete
revolution before you start counting. This will almost entirely eliminate errors due to
backlash in fine adjustment knob.
2. Always turn the fine adjustment knob in one direction either clockwise or anti-clockwise.
3. Direct eye exposure to laser should be avoided.
4. Observing laser interference fringes by reflecting mirror is prohibited.
5. Avoid touching any of the optics with bare hand.

Last updated in Dec 2017 © NISER Page 8