SFP Series 1.

25G up to 30km transmission

AN-UM-SFP-SM/LX1310
1.25Gbps SFP Transceiver

Features

Operating data rate up to 1.25Gbps

1310 nm FP LD Transmitter

Distance up to 30km

Single 3. 3V Power supply and TTL Logic
Interface
Applications

Duplex LC Connector Interface

Gigabit Ethernet Switches and

Hot Pluggable
Routers

Operating Case Temperature

Fiber Channel Switch
Standard: 0℃~+70℃，
Industrial:-40℃~+85℃ Infrastructure

Compliant with MSA SFP Specification
XDSL Applications

Digital diagnostic monitor interface
Metro Edge Switching
Compatible with SFF-8472

Product Description
The AN-UM-SFP-SM/LX1310 series single mode transceivers is small form factor
pluggable module for bi-directional serial optical data communications such as Gigabit
Ethernet 1000BASE-LX and Fiber Channel 1x SM-LC-L FC-PI. It is with the SFP
20-pin connector to allow hot plug capability. This module is designed for single mode
fiber and operates at a nominal wavelength of 1310 nm.
The transmitter section uses a multiple quantum well laser and is a class 1 laser
compliant according to International Safety Standard IEC-60825. The receiver section
uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header
and a limiting post-amplifier IC.
The AN-UM-SFP-SM/LX1310D series are designed to be compliant with SFF-8472
SFP Multi-source Agreement (MSA).
www.ad-net.com.tw
Page 1 of 10
SFP Series 1.25G up to 30km transmission

Regulatory Compliance
Feature Standard Performance
Electrostatic Discharge
MIL-STD-883E Class 1(>500 V)
(ESD) to the Electrical
Method 3015.7 Isolation with the case
Pins
Electromagnetic
FCC Part 15 Class B Compatible with standards
Interference (EMI)
FDA 21CFR 1040.10 and Compatible with Class I
1040.11 laser product.
Laser Eye Safety
EN60950, EN (IEC) Compatible with TüV
60825-1,2 standards
Component Recognition UL and CUL UL file E317337
Green Products RoHS RoHS6

Absolute Maximum Ratings

Parameter Symbol Min. Max. Unit
Storage Temperature TS -40 +85 °C
Supply Voltage VCC -0.5 3.6 V

Recommended Operating Conditions

Parameter Symbol Min. Typical Max. Unit
AN-UM-SFP-SM/L
0 +70
Operating Case X1310 X
TA °C
Temperature AN-UM-SFP-SM/L
-40 +85
X1310IX
Power Supply
VCC 3.15 3.3 3.45 V
Voltage
Power Supply
ICC 300 mA
Current
Surge Current ISurge +30 mA
Baud Rate 1.25 GBaud

PERFORMANCE SPECIFICATIONS - ELECTRICAL

Parameter Symbol Min. Typ. Max Unit Notes
TRANSMITTER
VLPECL AC coupled
Vin 400 2500 mVp
Inputs(Differential) inputs
Input Impedance Rin > 100
Zin 85 100 115 ohms
(Differential) kohms @ DC
Tx_DISABLE Input
2 3.45 V
Voltage - High

www.ad-net.com.tw
Page 2 of 10
SFP Series 1.25G up to 30km transmission
Tx_DISABLE Input
0 0.8 V
Voltage - Low
Tx_FAULT Output Io = 400µA;
2 Vcc+0.3 V
Voltage -- High Host Vcc
Tx_FAULT Output
0 0.5 V Io = -4.0mA
Voltage -- Low
RECEIVER
LVPECL Outputs AC coupled
Vout 400 800 1200 mVpp
(Differential) outputs
Output Impedance
Zout 85 100 115 ohms
(Differential)
Rx_LOS Output lo = 400µA;
2 Vcc+0.3 V
Voltage - High Host Vcc

Rx_LOS Output
0 0.8 V lo = -4.0mA
Voltage - Low
VoH 2.5 V
MOD_DEF ( 0:2 ) With Serial ID
VoL 0 0.5 V

Optical and Electrical Characteristics

Parameter Symbol Min. Typical Max. Unit
9µm Core AN-UM-SFP-SM/LX1310/10XX 10
Diameter AN-UM-SFP-SM/LX1310/20XX 20 Km
SMF AN-UM-SFP-SM/LX1310/30XX 30
Data Rate 1.25 Gbps
Transmitter
Centre Wavelength λC 1260 1310 1360 nm
Spectral Width (RMS) σ 3 nm
Average AN-UM-SFP-SM/LX1310/10XX -10 -3
Output AN-UM-SFP-SM/LX1310/20XX P0ut -6 -1 dBm
Power AN-UM-SFP-SM/LX1310/30XX -5 0
Extinction Ratio EX 9 dB
Rise/Fall Time(20%～80%) tr/tf 1.2 ns
Total Jitter TJ 56.5 ps
Output Optical Eye IUT-T G.957 Compliant
Data Input Swing Differential VIN 500 2000 mV
Input Differential Impedance ZIN 90 100 110 Ω
TX Disable 2.0 Vcc+0.3 V
Disable Enable 0 0.8
Fault 2.0 VCC+0.3
TX_Fault V
Normal 0 0.8
TX_Disable Assert Time t_off 10 us
Receiver
www.ad-net.com.tw
Page 3 of 10
SFP Series 1.25G up to 30km transmission
Centre Wavelength λC 1100 1600 nm
AN-UM-SFP-SM/LX1310/10XX -20
Receiver
AN-UM-SFP-SM/LX1310/20XX PIN -22 dBm
Sensitivity
AN-UM-SFP-SM/LX1310/30XX -23
Output Differential Impedance PIN 90 100 110 Ω
Data Output Swing Differential VOUT 370 2000 mV
Rise/Fall Time Tr/tf 2.2 ns
LOS De-Assert LOSD -24 dBm
LOS Assert LOSA -40 dBm
High 2.0 VCC+0.3
LOS V
Low 0 0.8

SFP Transceiver Electrical Pad Layout

Pin Function Definitions

Pin Plug
Name FUNCTION Notes
Num. Seq.

www.ad-net.com.tw
Page 4 of 10
SFP Series 1.25G up to 30km transmission
1 VeeT Transmitter Ground 1
Transmitter Fault
2 TX Fault 3 Note 1
Indication
Note 2, Module disables on
3 TX Disable Transmitter Disable 3
high or open
Note 3, Data line for Serial
4 MOD-DEF2 Module Definition 2 3 ID.

Note 3, Clock line for Serial

5 MOD-DEF1 Module Definition 1 3
ID.
Note 3, Grounded within the
6 MOD-DEF0 Module Definition 0 3
module.
7 Rate Select Not Connect 3 Function not available
8 LOS Loss of Signal 3 Note 4
9 VeeR Receiver Ground 1 Note 5
10 VeeR Receiver Ground 1 Note 5
11 VeeR Receiver Ground 1 Note 5
Inv. Received Data
12 RD- 3 Note 6
Out
13 RD+ Received Data Out 3 Note 7
14 VeeR Receiver Ground 1 Note 5
15 VccR Receiver Power 2 3.3 ± 5%, Note 7
16 VccT Transmitter Power 2 3.3 ± 5%, Note 7
17 VeeT Transmitter Ground 1 Note 5
18 TD+ Transmit Data In 3 Note 8
19 TD- Inv. Transmit Data In 3 Note 8
20 VeeT Transmitter Ground 1 Note 5

Notes:

1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K –

10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V.
When high, output indicates a laser fault of some kind. Low indicates normal operation.
In the low state, the output will be pulled to < 0.8V.

2) TX disable is an input that is used to shut down the transmitter optical output. It is
pulled up within the module with a 4.7 – 10 K Ω resistor. Its states are:
Low (0 – 0.8V): Transmitter on
(>0.8, < 2.0V): Undefined
High (2.0 – 3.465V): Transmitter Disabled

www.ad-net.com.tw
Page 5 of 10
SFP Series 1.25G up to 30km transmission

Open: Transmitter Disabled

3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with
a 4.7K – 10KΩresistor on the host board. The pull-up voltage shall be VccT or VccR
(see Section IV for further details). Mod-Def 0 is grounded by the module to indicate
that the module is present Mod-Def 1 is the clock line of two wire serial interface for
serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID

4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up

with a 4.7K – 10KΩ resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When
high, this output indicates the received optical power is below the worst-case receiver
sensitivity (as defined by the standard in use). Low indicates normal operation. In the
low state, the output will be pulled to < 0.8V.

5) VeeR and VeeT may be internally connected within the SFP module.

6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω
differential lines which should be terminated with 100Ω (differential) at the user
SERDES. The AC coupling is done inside the module and is thus not required on the
host board. The voltage swing on these lines will be between 370 and 2000 mV
differential (185 –1000 mV single ended) when properly terminated.

7) VccR and VccT are the receiver and transmitter power supplies. They are defined
as 3.3V ±5% at the SFP connector pin. Maximum supply current is 300mA.
Recommended host board power supply filtering is shown below. Inductors with DC
resistance of less than 1 ohm should be used in order to maintain the required voltage
at the SFP input pin with 3.3V supply voltage. When the recommended supply-filtering
network is used, hot plugging of the SFP transceiver module will result in an inrush
current of no more than 30mA greater than the steady state value. VccR and VccT
may be internally connected within the SFP transceiver module.

8) TD-/+: These are the differential transmitter inputs. They are AC-coupled,
differential lines with 100Ω differential termination inside the module. The AC coupling
is done inside the module and is thus not required on the host board. The inputs will

www.ad-net.com.tw
Page 6 of 10
SFP Series 1.25G up to 30km transmission

accept differential swings of 500 – 2400 mV (250 – 1200mV single-ended),

though it is recommended that values between 500 and 1200 mV differential (250 –
600mV single-ended) be used for best EMI performance.

EEPROM

The serial interface uses the 2-wire serial CMOS EEPROM protocol defined for the
ATMEL AT24C02/04 family of components. When the serial protocol is activated, the
host generates the serial clock signal (SCL). The positive edge clocks data into those
segments of the EEPROM that are not write protected within the SFP transceiver. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA) is
bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to
mark the start and end of serial protocol activation. The memories are organized as a
series of 8-bit data words that can be addressed individually or sequentially.

The Module provides diagnostic information about the present operating conditions.
The transceiver generates this diagnostic data by digitization of internal analog signals.
Calibration and alarm/warning threshold data is written during device manufacture.
Received power monitoring, transmitted power monitoring, bias current monitoring,
supply voltage monitoring and temperature monitoring all are implemented. The
diagnostic data are raw A/D values and must be converted to real world units using
calibration constants stored in EEPROM locations 56 – 95 at wire serial bus address
A2h. The digital diagnostic memory map specific data field define as following .For
detail EEPROM information, please refer to the related document of SFF 8472 Rev 9.3

www.ad-net.com.tw
Page 7 of 10
SFP Series 1.25G up to 30km transmission

Recommend Circuit Schematic

Mechanical Specifications
www.ad-net.com.tw
Page 8 of 10
SFP Series 1.25G up to 30km transmission

Ordering information
Data Fibre Optical
Part No. Laser Distance DDMI
Rate Type Interface
1310nm
AN-UM-SFP-SM/LX1310/10 1.25Gbps SMF 10Km LC NO
FP
1310nm
AN-UM-SFP-SM/LX1310/10D 1.25Gbps SMF 10Km LC YES
FP
1310nm
AN-UM-SFP-SM/LX1310/10I 1.25Gbps SMF 10Km LC NO
FP
1310nm
AN-UM-SFP-SM/LX1310/10ID 1.25Gbps SMF 10Km LC YES
FP
1310nm
AN-UM-SFP-SM/LX1310/20 1.25Gbps SMF 20Km LC NO
FP
1310nm
AN-UM-SFP-SM/LX1310/20D 1.25Gbps SMF 20Km LC YES
FP
1310nm
AN-UM-SFP-SM/LX1310/20I 1.25Gbps SMF 20Km LC NO
FP
1310nm
AN-UM-SFP-SM/LX1310/20ID 1.25Gbps SMF 20Km LC YES
FP
1310nm
AN-UM-SFP-SM/LX1310/30 1.25Gbps SMF 30Km LC NO
FP
AN-UM-SFP-SM/LX1310/30D 1.25Gbps 1310nm SMF 30Km LC YES
www.ad-net.com.tw
Page 9 of 10
SFP Series 1.25G up to 30km transmission
FP
1310nm
AN-UM-SFP-SM/LX1310/30I 1.25Gbps SMF 30Km LC NO
FP
1310nm
AN-UM-SFP-SM/LX1310/30ID 1.25Gbps SMF 30Km LC YES
FP

* I--- Industrial operating temperature

* D--- DDMI

NOTICE:
AD-net reserves the right to make changes to or discontinue any optical link product or
service identified in this publication, without notice, in order to improve design and/or
performance. Applications that are described herein for any of the optical link products
are for illustrative purposes only. AD-net makes no representation or warranty that
such applications will be suitable for the specified use without further testing or
modification.

CONTACT:
AD-NET TECHNOLOGY CO.,LTD

Address: No.30-3, Lane 393, Yuantong Rd.,

Zhonghe City, Taipei County 235, Taiwan

TEL: +886-4-24523169

FAX: +886-4-24527841

email: [email protected]

www.ad-net.com.tw
Page 10 of 10