Scribd
Upload
112 views

Sensor de Ca Con Arduino lm358

To connect a CT sensor to an Arduino, a burden resistor is used to convert the current output of the CT sensor to a voltage signal. A voltage divider with resistors R1 and R2 adds a DC bias so the signal swings above and below half the Arduino's analog reference voltage. The burden resistor value depends on the CT sensor specifications, the desired current range, and the Arduino's analog reference voltage. A capacitor bypasses the resistors for the AC signal from the CT sensor.

Uploaded by

Wilfredo Cindet
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
112 views

Sensor de Ca Con Arduino lm358

To connect a CT sensor to an Arduino, a burden resistor is used to convert the current output of the CT sensor to a voltage signal. A voltage divider with resistors R1 and R2 adds a DC bias so the signal swings above and below half the Arduino's analog reference voltage. The burden resistor value depends on the CT sensor specifications, the desired current range, and the Arduino's analog reference voltage. A capacitor bypasses the resistors for the AC signal from the CT sensor.

Uploaded by

Wilfredo Cindet
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

https://learn.openenergymonitor.

org/electricity-monitoring/ct-sensors/interface-with-
arduino?redirected=true

CT Sensors - Interfacing with an Arduino

To connect a CT sensor to an Arduino, the output signal from the CT sensor needs to be
conditioned so it meets the input requirements of the Arduino analog inputs, i.e. a positive
voltage between 0V and the ADC reference voltage.

Note: This page give the example of an Arduino board working at 5 V and of the EmonTx
working at 3.3 V. Make sure you use the right supply voltage and bias voltage in your
calculations that correspond to your setup.

This can be achieved with the following circuit which consists of two main parts:

1. The CT sensor and burden resistor


2. The biasing voltage divider (R1 & R2)

Calculating a Suitable Burden Resistor Size

If the CT sensor is a "current output" type such as the YHDC SCT-013-000, the current
signal needs to be converted to a voltage signal with a burden resistor. If it is a voltage
output CT you can skip this step and leave out the burden resistor, as the burden resistor is
built into the CT.

a) Choose the current range you want to measure

The YHDC SCT-013-000 CT has a current range of 0 to 100 A. For this example, let's
choose 100 A as our maximum current.

b) Convert maximum RMS current to peak-current by multiplying by √2.

Primary peak-current = RMS current × √2 = 100 A × 1.414 = 141.4A

c) Divide the peak-current by the number of turns in the CT to give the peak-current
in the secondary coil.

The YHDC SCT-013-000 CT has 2000 turns, so the secondary peak current will be:
Secondary peak-current = Primary peak-current / no. of turns = 141.4 A
/ 2000 = 0.0707A

d) To maximise measurement resolution, the voltage across the burden resistor at


peak-current should be equal to one-half of the Arduino analog reference voltage.
(AREF / 2)

If you're using an Arduino running at 5V: AREF / 2 will be 2.5 Volts. So the ideal burden
resistance will be:

Ideal burden resistance = (AREF/2) / Secondary peak-current = 2.5 V /


0.0707 A = 35.4 Ω

35 Ω is not a common resistor value. The nearest values either side of 35 Ω are 39 and 33
Ω. Always choose the smaller value, or the maximum load current will create a voltage
higher than AREF. We recommend a 33 Ω ±1% burden. In some cases, using 2 resistors in
series will be closer to the ideal burden value. The further from ideal the value is, the lower
the accuracy will be.

Here are the same calculations as above in a more compact form:

Burden Resistor (ohms) = (AREF * CT TURNS) / (2√2 * max primary


current)

Burden resistor sizing for OpenEnergyMonitor energy monitoring hardware.

emonTx V3 (see guide)

The emonTx V3 uses a 3.3V regulator, so it's VCC and therefore AREF, will always be 3.3V
regardless of battery voltage. The standard emonTx V3 uses 22Ω burden resistors for CT
1, 2 and 3, and a 120Ω resistor for CT4, the high sensitivity channel. See the emonTx V3
technical wiki
at: https://wiki.openenergymonitor.org/index.php?title=EmonTx_V3#Burden_Resistor_Calc
ulations.

emonPi (see guide)

The EmonPi has two CT channels both with 22Ω burden resistors.

emonTx V2

If you're using a battery powered emonTx V2, AREF will start at 3.3 V and slowly decrease
as the battery voltage drops to 2.7 V. The ideal burden resistance for the minimum voltage
would therefore be:
Ideal burden resistance = (AREF/2) / Secondary peak-current = 1.35V /
0.0707A = 19.1 Ω

19 Ω is not a common value. We have a choice of 18 or 22 Ω. We recommend using an 18


Ω ±1% burden.

Tool for calculating burden resistor size, CT turns and max Irms (thanks to Tyler Adkisson
for building and sharing this).

(Note: this tool does not take into account maximum CT power output. Saturation and
distortion will occur if the maximum output is exceeded. Nor does it take into account
component tolerances, so the burden resistor value should be decreased by a few (~5)
percent allow some "headroom." There is more info about component tolerances at: ACAC
Component tolerances.)

Adding a DC Bias

If you were to connect one of the CT wires to ground and measure the voltage of the
second wire, relative to ground, the voltage would vary from positive to negative with
respect to ground. However, the Arduino analog inputs require a positive voltage. By
connecting the CT lead we connected to ground, to a source at half the supply voltage
instead, the CT output voltage will now swing above and below 2.5 V thus remaining
positive.

Resistors R1 & R2 in the circuit diagram above are a voltage divider that provides the 2.5 V
source (1.65 V for the emonTx). Capacitor C1 has a low reactance - a few hundred ohms -
and provides a path for the alternating current to bypass the resistor. A value of 10 μF is
suitable.

Choosing a suitable value for resistors R1 & R2

Higher resistance lowers quiescent energy consumption.

We use 10 kΩ resistors for mains powered monitors. The emonTx uses 470 kΩ resistors to
keep the power consumption to a minimum, as it is intended to run on batteries for several
months.

Arduino Sketch

To use the above circuit to measure RMS current, with an assumed fixed RMS voltage
(e.g. 240V) to indicate approximate apparent power, use this Arduino sketch: Arduino
sketch - current only

CT Sensors
In this Chapter:

o 1. Introduction

o 2. Installation

o 3. Interfacing with an Arduino

o 4. How to Build an Arduino Energy Monitor Measuring Current Only

o Advanced: Measurement Implications of ADC Resolution at Low Current Values

o Extending CT Sensor Cable

o YHDC SCT-013-000 CT Sensor Report

 YHDC SCT006 CT Sensor Report

You might also like