Scribd
Upload
238 views

Assignment Retaining Wall - Question

This document provides instructions for Assignment 2 of the course BFC32803 Structure Concrete Design II. It includes 4 questions related to retaining wall design. Question 5.1-5.3 provide specific design scenarios to analyze the stability, loads, and reinforcement design of different cantilever retaining walls. Question 5.4 asks students to describe two types of retaining wall failures and perform design checks and reinforcement sizing for another retaining wall example.

Uploaded by

AidaFarzanaNana
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
238 views

Assignment Retaining Wall - Question

This document provides instructions for Assignment 2 of the course BFC32803 Structure Concrete Design II. It includes 4 questions related to retaining wall design. Question 5.1-5.3 provide specific design scenarios to analyze the stability, loads, and reinforcement design of different cantilever retaining walls. Question 5.4 asks students to describe two types of retaining wall failures and perform design checks and reinforcement sizing for another retaining wall example.

Uploaded by

AidaFarzanaNana
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

BFC32803: STRUCTURE CONCRETE DESIGN II

ASSIGNMENT 2: TOPIC 5: RETAINING WALL


ASSIGNMENT BY GROUP

SUBMISSION DUE: 16 DECEMBER 2018 (SUNDAY), BY 5.00PM

QUESTION 5.1:

BFC32803/RetainingWall/Assignment/Sem120182019/TNTC
QUESTION 5.2:

BFC32803/RetainingWall/Assignment/Sem120182019/TNTC
QUESTION 5.3:

(a) Specific the function of retaining wall and describe the compulsory elements that should
be designed for a retaining wall to retain well-drained soil with depth more than 5 m.

(b) A cantilever wall as shown in figure below support a bank earth 5.0 m height. The soil
behind the wall has density of 1900 kg/m3 with angle of internal friction of 30º. Given the
following data:

Characteristic strength of concrete = 35 N/mm2


Characteristic strength of steel = 500 N/mm2
Coefficient of friction = 0.5
Soil cohesion =0
Soil bearing pressure = 150 kN/m2
Earth pressure = 31.67 kN/m2

(i) Determine the total horizontal load, vertical load and moment of the retaining wall.
(ii) Check the soil pressure at the toe of retaining wall.
(iii) Predict the ability of retaining wall toward stability against overturning, resistance
to sliding and settlement.
(iv) Design the bending reinforcement using bar diameter=20mm, cover=45mm.

FIGURE Q1

BFC32803/RetainingWall/Assignment/Sem120182019/TNTC
QUESTION 5.4:

(a) Describe briefly TWO (2) types of failure in retaining wall.

(b) Figure below shows a cross section of a retaining wall. The surcharge of 2.0 kN/m2 is
imposed to the backfill behind the wall. The soil has a density, γ = 18 kN/m3, angle of
internal friction, ϕ = 32o and cohesion, c = 0. The material under the wall has a safe bearing
pressure 80 kN/m2, friction coefficient is 0.5 and concrete density is 25 kN/m3.

(i) Determine the total horizontal load, vertical load and moment of the retaining wall.
(ii) Check for stability of the wall against overturning, sliding and settlement. Partial
safety factor as shown in Table 1. Give your reason and comment if the stability is
not adequate.
(iii) Design the bending reinforcement if heel length is assumed 2500mm, by using high-
yield steel, fyk=500 N/mm2, fck=30 N/mm2, bar diameter=20mm, cover=45mm.

Table 1: Partial safety factor at the ultimate limit state (BS8110)

Situation Imposed Stabilizing


Overturning 1.4 1.0
Sliding 1.4 -
2
surcharge = 2.0 kN/m

4000

400

600

3000 450
All units in mm

4000

BFC32803/RetainingWall/Assignment/Sem120182019/TNTC

You might also like