Scribd
Upload
125 views5 pages

Instructions For Replacing The Engage - Disengage Gears

This document provides instructions for replacing the engage/disengage gears in the external heat roller assembly of a Canon printer. It is a multi-step process that involves removing numerous covers, ducts, and printed circuit boards to access the gears. Specific gears are to be replaced with new gears of different tooth counts. Grease must be applied to the tooth surfaces of each new gear before reassembling the heat roller assembly.

Uploaded by

Andi Prenga
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
125 views5 pages

Instructions For Replacing The Engage - Disengage Gears

This document provides instructions for replacing the engage/disengage gears in the external heat roller assembly of a Canon printer. It is a multi-step process that involves removing numerous covers, ducts, and printed circuit boards to access the gears. Specific gears are to be replaced with new gears of different tooth counts. Grease must be applied to the tooth surfaces of each new gear before reassembling the heat roller assembly.

Uploaded by

Andi Prenga
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Canon

TP12 430.pdf
COMPANION DOCUMENT

Instructions for Replacing the Engage/Disengage


Gears in the External Heat Roller Assembly
Steps to replace the engage/disengage gears in the external heat roller assembly

Prepare the following items before starting the 4) Remove the connectors from the PCB. (24
work. connectors)
- FL3-7951-000 1pc. (20T/42T Gear)
- FL3-7952-000 1pc. (18T/45T Gear)
- FL3-7953-000 1pc. (15T/36T Gear)
- FU7-0828-010 1pc. (40T Gear)
- FY9-6026-000 (Lube, Molykote G-8022 Grease)

1) Remove the rear left cover. (12 screws (loosen),


3 screws (remove) )

5) Remove the fixing main driver PCB. (6 screws)

2) Remove the rear right cover. (6 screws)

6) Remove Ground wire. (1 screw)


7) Disconnect all connectors on the PCB. (4
connectors)
8) Remove Developing high-voltage PCB. (6 claws
[1])

3) Remove the rear lower cover. (7 screws)

1/4
Steps to replace the engage/disengage gears in the external heat roller assembly

9) Remove the feeder assembly exhaust duct [1]. 9-3) Remove the waste toner TCL pipe. (1 screw
[1])
9-4) Remove the feeder assembly exhaust duct.
(2 screws [1])

9-1) Remove the ITB post duct. (1 screw [1])

9-2) Remove the 4 fans duct. (harness [1], 2


screws [2])

2/4
Steps to replace the engage/disengage gears in the external heat roller assembly

10) Remove the harness and the tie-wraps.


12) Remove the fixing drive assembly. (4
connectors [1], 6 screws [2])

11) Remove the exhaust fan duct. (2 screws [1])

13) Remove the PCB support plate from the fixing


drive assembly. (3 screws [1])

3/4
Steps to replace the engage/disengage gears in the external heat roller assembly

14) Remove 5 gears. (1 bearing [1], 4 E-rings [2],


1 dowel pin [3], 2 washers [4])

15) Replace 4 gears with the new type gears. Then,


reverse the steps to place the parts back. (Be
sure to apply the grease of about three grains
of rice to the tooth surfaces of each gear.)

4/4

You might also like