Scribd
Upload
319 views3 pages

Method Statement For Precommissioning & Commissioning of Close Control Units CCU's

This document outlines the precommissioning and commissioning procedures for Close Control Units (CCUs). The 22-step precommissioning procedure ensures the CCU installation is complete and checks components like piping, insulation, electrical connections, and accessibility. The 16-step commissioning procedure turns on the unit and tests alarms, temperatures, currents, valve operation, and air flow to verify proper functioning. Attachments include check sheets, a performance test record, risk assessment, and manufacturer instructions.

Uploaded by

vin ss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
319 views3 pages

Method Statement For Precommissioning & Commissioning of Close Control Units CCU's

This document outlines the precommissioning and commissioning procedures for Close Control Units (CCUs). The 22-step precommissioning procedure ensures the CCU installation is complete and checks components like piping, insulation, electrical connections, and accessibility. The 16-step commissioning procedure turns on the unit and tests alarms, temperatures, currents, valve operation, and air flow to verify proper functioning. Attachments include check sheets, a performance test record, risk assessment, and manufacturer instructions.

Uploaded by

vin ss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Method Statement For

Precommissioning &
Commissioning of Close
Control Units CCU’s
 HVAC Method Statements
 Testing & Commissioning

308



 0
 


 Share

The purpose of this safe work method of statement or procedure is to define the step by
step method to implement the correct practices for theprecommissioning &
commissioning of Close Control Units or CCU’s through the guidelines contained herein
so as to ensure that the job execution complies with the project requirements and serves
the intended function to satisfactory level.

Precommissioning Procedure for


Close Control Units CCU
1. Ensure that the unit installation is complete and mechanical completion is approved.
2. Ensure that no damage occurs between mechanical completion
& precommissioning.
3. Repair all damages to the equipment finish paint.
4. Check CCU is installed as per the approved shop drawings and manufacturer’s
instructions.
5. Check the level of the mounting frame is same as the raised floor level.
6. Check the unit is properly fixed to the support
7. Check the CCUs are independent from the raised floor
8. Check the vibration isolator pads are installed
9. Check all chilled water piping, connected to CCU is with proper flexible
connectors,valve package, drain, air vents, instruments, etc as per the approved shop
drawing & manufacturer’s instructions.
10. Check for the installation & insulation of condensate drain piping as per the approved
shop drawings.
11. Check for proper electrical power, control panel, BMS and earthing connections as
per manufacturer’s recommendations. Field wiring to be pre-tested for continuity and
insulation resistance.
12. Check the interfacing with the fire alarm system & BMS.
13. Check & record the voltage at the disconnect.
14. Check & record the voltage at all control voltage transformers.
15. Check all valves in the raised floor voids are accessible
16. Check the U-trap in the condesate drain piping is provided.
17. Check the piping connections to the units are done by using approved flexibles & as
per manufacturer’s requirement.
18. Check the identification is completed for the piping & the unit.
19. Check sound attenuators are installed on the top of the units
20. Check the water supply pipes are connected to the unit.
21. Check that minimum distance from walls & full access for maintenance has been
provided.
22. Check that supply air from unit is not blocked by other services.
Commissioning Method for Close
Control Unit
1. Ensure that all the precommissioning checks are carried out successfully.
2. Turn ON the main disconnect.
3. Check the fan rotation is proper & free from any abnormal noise or vibration.
4. Check main fan current & record in the performance test record sheet.
5. Advance temperature set point to energise reheat, check reheat current & record.
6. Advance humidity set point to energise humidifier, check the current & record.
7. Adjust temperature set point to energise valve motor, check for full valve travel in
cooling mode & for valve closure.
8. Check high temperature alarm.
9. Check low temperature alarm.
10. Check high humidity alarm.
11. Check low humidity alarm.
12. Check loss of air flow (the static pressure measuring tube shall be removed & the
signal for loss of air flow shall be proven)
13. Check for proper functioning of humidifier ( the humidity set point shall be increased
& the functioning of the humidifier shall be proven).
14. Check leak detection alarm.
15. Check smoke detection alarm (an NO/NC electrical signal shall be simulated and the
smoke alarm shall be proven).
16. Check & record ON/ OFF coil temperature & Air flow (cfm).

ATTACHMENTS

 Precommissioning check sheet for Close Control Units


 Commissioning check sheet for Close Control Units
 Performance Test Record for Close Control Units
 Risk Assesment
 Manufacturer’s instructions

You might also like