Scribd
Upload
1K views1 page

Din 522 Tol. Arruelas

The document provides specifications for dimensional and geometric tolerances of washers. It lists the tolerances for various dimensions like clearance hole diameter, outside diameter, thickness, chamfer size, and flatness for washer nominal sizes from below 0.5mm to above 20mm and for product classes A and C.

Uploaded by

Bruno Parolini
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views1 page

Din 522 Tol. Arruelas

The document provides specifications for dimensional and geometric tolerances of washers. It lists the tolerances for various dimensions like clearance hole diameter, outside diameter, thickness, chamfer size, and flatness for washer nominal sizes from below 0.5mm to above 20mm and for product classes A and C.

Uploaded by

Bruno Parolini
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Products mentioned in this technical documentation are available from MARYLAND METRICS P.O.

Box 261 Owings Mills, MD 21117 USA


ph: (410)358-3130 (800)638-1830 fx: (410)358-3142 (800)872-9329 web: http://mdmetric.com email: [email protected]
Tolerances for washers

Dimensions tolerances  Form and position tolerances 




 

detail
 

The washers shown are just examples. The specifications are valid correspondingly also for other standardised and non-standardised
washer types.

In the following tables, only the specifications for commercially available product classes A and C are listed.

The reference value is the individual value specified in the corresponding product standards.
For dimensions without a tolerance specification ISO 2768 (DIN 7168) m for product class A is valid, ISO 2768 (DIN 7168) g for
product class C.

Dimensions tolerances Form and position tolerances

Characteristic Nominal size Product class Characteristic Nominal size Product class

>  A (m) C (g) >  A (m) C (g)

 Clearance hole d1 h d1*  Thickness variation h  h*


on the same part
– 4 H13 H14 – 0.5 0.025
1 0.5 1.0 0.05
w = ——— (d2 – d1)
* h' is the part of the 4 – H14 H15 2 1.0 2.5 0.10
hole within the (d2 + d1) 2.5 4.0 0.15 –
d3 = ————
tolerance specified h (h') min 2 4.0 6.0 0.20
for d1. *  h only applies in the range 6.0 10 0.30
– 4  0.5 h from d3 – 0.3 w to d3 + 0.3 w 10 20 0.40

4 –  0.3 h  Flatness h c* (t2) **

 Outside diameter d2 h d2 – 0.5 0.10


* Tolerance c (t2) is 0.5 1.0 0.15
– 4 h14 h16 always independent 1.0 2.5 0.20
of the thickness 2.5 4.0 0.30 –
4 – h15 h16 tolerance for h. 4.0 6.0 0.40
6.0 10 0.60
 Washer thickness h h Tol. mm 6.0 10 0.60

– 0.5 ± 0.05 ± 0.10


0.5 1.0 ± 0.10 ± 0.20
1.0
2.5
2.5
4.0
± 0.20
± 0.30
± 0.30
± 0.60
For washers from stainless steel } == 1.5c
2 c (DIN 522)
(ISO 4759-3)
4.0 6.0 ± 0.60 ± 1.00
6.0 10 ± 1.00 ± 1.20
10 20 ± 1.20 ± 1.60  Coaxiality b d2 b (t1)
(dependent on d2)
 Chamfer  30–45° – 50 2 IT12 2 IT15
e min 0.25 h –
e max 0.50 h 50 – 2 IT13 2 IT16

Excerpt from ISO 4759-3 (DIN 522)

TI-90
copyright 2011 maryland metrics/f. reyher nchfg gmbh + co kg
This technical information is provided by the courtesy of F. Reyher Nchfg GmbH + Co KG, Hamburg/Germany, with some editing by Maryland Metrics

You might also like