Scribd
Upload
37 views3 pages

¿Ï Checking The Readings of Ref - Cell at Various Points (TUCH

This document provides instructions for checking the readings of a reference cell at various points of an impressed current cathodic protection system. It details 14 steps to check readings at cofferdams, inside the control panel terminals, and at cable connector blocks. The final section lists actual voltage readings from testers compared to display readings for the forward and aft systems.

Uploaded by

Valerian Gheorghe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
37 views3 pages

¿Ï Checking The Readings of Ref - Cell at Various Points (TUCH

This document provides instructions for checking the readings of a reference cell at various points of an impressed current cathodic protection system. It details 14 steps to check readings at cofferdams, inside the control panel terminals, and at cable connector blocks. The final section lists actual voltage readings from testers compared to display readings for the forward and aft systems.

Uploaded by

Valerian Gheorghe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

DOC. NO.

CP-RFC-01-3

K.C. LTD. I.C.C.P SYSTEM REV. 2


DATE 2013-04-23
Impressed Current Cathodic Protection System
PAGE 2

ITEM Ref.cell
Checking the readings of ref.cell at various points
SCOPE
(TUCHCON)

1. Confirm the system works on AUTO MODE.

At cofferdams

2. F irst
s cure t e ank(s)
i e a s v mptied h asb nd
m
een i entilation
ade n
case F WD
s i l ystem i s ’ss t anks(
ocated forepeak
t n o hip ank r
ballast tank).

3. Open t c he offerdam
l J b fid(or
P r unction
M a ox)
r t orr ORT
o ef.ce
output D v C b oltagep r etween
i c aort h bef.cell
t i t nb offerdam
t
(No.14 Checking result).
※ Each r ef.cell
c s bable
c hould
w t m e l onnected
o t “-“) a ndh ith s ull heb hould
inus
connected with the plus lead of tester(“+”)

4. Open t c he offerdam
l J b fid(or
S r unctionM a ox)
r t or r T’BD
o ef.c
output DC voltage between st’bd ref.cell in cofferdam and hull by tester as above.

5. Check t r he o eadings
s e fo t ensing
d d lectrode
o c p an r he a igital
above.

In terminals inside control panel

6. O enp t hec ontrol


p a canel t tnd heck he erminal
numbers inside control panel.

7. Disconnect a t cnd tightly


P r onnect
c he ORT ef.cell able(#
Measure a r ndt r ecord o o he D veadings b pf r utput a h C
b t oltage
as above.
DOC. NO. CP-RFC-01-3

K.C. LTD. I.C.C.P SYSTEM REV. 2


DATE 2013-04-23
Impressed Current Cathodic Protection System
PAGE 2

8. Disconnect a t c nd t ightly
S r onnect
c Mhe aT’BD
r t ref.cell o able(#1
output DC voltage between st’bd ref.cell and hull by tester as above.

9. Check t r he o eadings
s e f o t ensing
d d lectrode
o c p na r he igital
as above.

Cable connector on PCB’s terminal block

10. Check the PCB’s terminal block inside control panel.

11. Disconnect a t nd c ightly t P onnect he ORT


ref.cell(C1) c able c onnector.
M a r easure
t r o nd ecord he eadings
output D v C b oltage p r etween
a h b ort
t ef.cell nd ull y
as above.

12. Disconnect a t c nd t ightly


S r onnect
(C2) c ablec he onnector.
T’BD
M a r ef.celleasure
t
readings of output DC voltage between st’bd ref.cell and hull by tester as above.

13. Check t r he o eadings


s e f o t ensing
d d lectrode
o c p an r he igital
as above.

14. Checking result


<FWD system>
Actual mV by tester Readings on display
Result
PORT ST’BD PORT ST’BD
At cofferdam 0.171 mV 0.115 mV 0.169 mV 0.114 mV
In terminals inside control panel 0.170 mV 0.113 mV 0.171 mV 0.115 mV
Cable connector on PCB’s terminal block 0.168 mV 0.111 mV 0.169 mV 0.113 mV

<AFT system>
Actual mV by tester Readings on display
Result
PORT ST’BD PORT ST’BD
At cofferdam 0.175 mV 0.187 mV 0.177 mV 0.185 mV
In terminals inside control panel 0.180 mV 0.191 mV 0.181 mV 0.190 mV
Cable connector on PCB’s terminal block 0.186 mV 0.196 mV 0.184 mV 0.197 mV
DOC. NO. CP-RFC-01-3

K.C. LTD. I.C.C.P SYSTEM REV. 2


DATE 2013-04-23
Impressed Current Cathodic Protection System
PAGE 2

15. Send the report to us([email protected]


[email protected]) for evaluation/analysis.

You might also like