HCC4538B

HCF4538B

DUAL MONOSTABLE MULTIVIBRATOR

. RETRIGGERABLE/RESETTABLE

. CAPABILITY
TRIGGER AND RESET PROPAGATION DE-

. LAYS INDEPENDENT OF RX, CX

TRIGGERING FROM LEADING OR TRAILING

.. EDGE
Q AND Q BUFFERED OUTPUTS AVAILABLE

.. SEPARATE RESETS
WIDE RANGE OF OUTPUT-PULSE WIDTHS
QUIESCENT CURRENT SPECIFIED TO 20V
EY
(Plastic Package)
F
(Ceramic Package)

.. FOR HCC DEVICE

5V, 10V, AND 15V PARAMETRIC RATINGS
SCHMITT TRIGGER INPUT ALLOWS UN-
LIMITER RISE AND FALL TIMES ON + TR AND

. – TR INPUTS
INPUT CURRENT OF 100nA AT 18V AND 25°C

.. FOR HCC DEVICE

100% TESTED FOR QUIESCENT CURRENT
MEETS ALL REQUIREMENTS OF JEDEC TEN-
M1
(Micro Package)
C1
(Chip Carrier)

TATIVE STANDARD N° 13A, ”STANDARD SPE- ORDER CODES :

CIFICATIONS FOR DESCRIPTION OF ”B” HCC4538BF HCF4538BM1
HCF4538BEY HCF4538BC1
SERIES CMOS DEVICES”

DESCRIPTION
The HCC4538B (extended temperature range) and
HCF4538B (intermediate temperature range) are PIN CONNECTIONS
monolithic integrated circuit, available in 16-lead
dual in-line plastic or-ceramic package and plastic
micro package. The HCC/HCF4538B dual precision
monostable multivibrator provides stable retrigger-
able/resettable one-shot operation for any fixed-
voltage timing application. An external resistor (RX)
and an external capacitor (CX) control the timing and
accuracy for the circuit. Adjustment of RX and CX
provides a wide range of output pulse widths from
the Q and Q terminals. The time delay from trigger
input to output transition (trigger propagation delay)
and the time delay from reset input to output transi-
tion (reset propagation delay) are independent of RX
and CX. Precision control of output pulse widths is
achieved through linear CMOS techniques. Lead-
ing-edge-triggering (+ TR) and trailing-edge-trigger-
ing (– TR) inputs are provided for triggering from
either edge of an input pulse. An unused + TR input
should be tied to VSS. An unused – TR input should
be tied to VDD. A RESET (on low level) is provided
for immediate termination of the output pulse or to

September 1988 1/14

HCC/HCF4538B

prevent output pulses when power is turned on. An when leading-edge triggering (+ TR) is used or Q is
unused RESET input should be tied to VDD. How- connected to + TR when trailingedge triggering (–
ever, if an entire section of the HCC/HCF4538B is TR) is used. The time period (T) for this multivibrator
not used, its inputs must be tied to either VDD or VSS can be calculated by : T = RX CX. The min. value of
(see table 1). In normal operation the circuit triggers external resistance, RX, is 4KΩ. The max. and min.
(extends the output pulse one period) on the appli- values of external capacitance, C X, are 100µF and
cation of each new trigger pulse. For operation in the 5nF, respectively.
non-retriggerable mode, Q is connected to – TR

FUNCTIONAL DIAGRAM

ABSOLUTE MAXIMUM RATING

Symbol Parameter Value Unit

VDD * Supply Voltage: HCC Types -0.5 to +20 V
HCF Types -0.5 to +18 V
Vi Input Voltage -0.5 to VDD + 0.5 V
II DC Input Current (any one input) ± 10 mA
Ptot Total Power Dissipation (per package) 200 mW
Dissipation per Output Transistor
for Top = Full Package Temperature Range 100 mW
o
Top Operating Temperature: HCC Types -55 to +125 C
o
HCF Types -40 to +85 C
o
Tstg Storage Temperature -65 to +150 C
Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress ratingonly and functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for external periods may affect device reliability.
* All voltage values are referred to VSS pin voltage.

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Value Unit
VDD Supply Voltage: HCC Types 3 to 18 V
HCF Types 3 to 15 V
VI Input Voltage 0 to VDD V
o
Top Operating Temperature: HCC Types -55 to +125 C
o
HCF Types -40 to +85 C

2/14
 HCC/HCF4538B

LOGIC DIAGRAM (1/2 of device shown)

TABLE 1: Functional Terminal Connections

Input Pulse to Other
VDD to Term. NO VSS to Term. NO
Term. No Connections
Function
Mono Mono Mono Mono Mono Mono Mono Mono
(1) (2) (1) (2) (1) (2) (1) (2)
Leading-Edge 3, 5 11, 13 4 12
Trigger/Retriggerable
Leading-Edge 3 13 4 12 5, 7 11, 9
Trigger/Non-retriggerable
Trailing-Edge 3 13 4 12 5 11
Trigger/Retriggerable
Trailing-Edge 3 13 5 11 4, 6 12, 10
Trigger/Non-retriggerable
Notes : 1. A Retriggerable one-shot multivibrator has an output pulse width which is extended on full time period (T) after application of the last
trigger pulse.
2. A Non-retriggerable one-shot multivibrator has a time period (T) referenced from the application of the first trigger pulse.

Pulse Width

3/14
HCC/HCF4538B

STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions)

Test Conditios Value
Symbol Parameter VI VO |IO| VDD TLOW * 25 oC THIGH * Unit
(V) (V) (µA) (V) Min. Max. Min. Typ. Max. Min. Max.
IL Quiescent 0/5 5 5 0.04 5 150
Current HCC 0/10 10 10 0.04 10 300
Types
0/15 15 20 0.04 20 600
µA
0/20 20 100 0.08 100 3000
0/5 5 5 0.04 5 150
HCF
Types 0/10 10 10 0.04 10 300
0/15 15 20 0.04 20 600
V OH Output High 0/5 <1 5 4.95 4.95 5 4.95
Voltage 0/10 <1 10 9.95 9.95 10 9.95 V
0/15 <1 15 14.95 14.95 15 14.95
VOL Output Low 5/0 <1 5 0.05 0.05 0.05
Voltage 10/0 <1 10 0.05 0.05 0.05 V
15/0 <1 15 0.05 0.05 0.05
VIH Input High 0.5/4.5 <1 5 3.5 3.5 3.5
Voltage 1/9 <1 10 7 7 7 V
1.5/13.5 <1 15 11 11 11
V IL Input Low 4.5/0.5 <1 5 1.5 1.5 1.5
Voltage 9/1 <1 10 3 3 3 V
13.5/1.5 <1 15 4 4 4
IOH Output 0/5 2.5 5 -2 -1.6 -3.2 -1.15
Drive HCC 0/5 4.6 5 -0.64 -0.51 -1 -0.36
Current Types
0/10 9.5 10 -1.6 -1.3 -2.6 -0.9
0/15 13.5 15 -4.2 -3.4 -6.8 -2.4 mA
0/5 2.5 5 -1.8 -1.6 -3.2 -1.3
HCF 0/5 4.6 5 -0.61 -0.51 -1 -0.42
Types
0/10 9.5 10 -1.5 -1.3 -2.6 -1.1
0/15 13.5 15 -4 -3.4 -6.8 -2.8
IOL Output 0/5 0.4 5 0.64 0.51 1 0.36
HCC
Sink 0/10 0.5 10 1.6 1.3 2.6 0.9
Types
Current
0/15 1.5 15 4.2 3.4 6.8 2.4 mA
0/5 0.4 5 0.61 0.51 1 0.42
HCF
Types 0/10 0.5 10 1.5 1.3 2.6 1.1
0/15 1.5 15 3.6 3.4 6.8 2.8
IIH, IIL Input Leakage
0/18 Any Input 18 ±0.1 ±10-5 ±0.1 ±1 µA
Current
CI Input Capacitance Any Input 5 7.5 pF
* TLOW = -55 oC for HCC device: -40 oC for HCF device.
* THIGH = +125 oC for HCC device: +85 oC for HCF device.
The Noise Margin for both ”1” and ”0” level is: 1V min. with VDD = 5 V, 2 V min. with VDD = 10 V, 2.5 V min. with VDD = 15 V

4/14
 HCC/HCF4538B

DYNAMIC ELECTRICAL CHARACTERISTICS (Tamb = 25 o C, C L = 50 pF, RL = 200 KΩ,

o
typical temperature coefficent for all VDD values is 03 %/ C, all input rise and fall times= 20 ns)
Test Conditions Value
Symbol Parameter Unit
VDD (V) Min. Typ. Max.
tTLH Transition Time 5 100 200
tTHL 10 50 100 ns
15 40 80
tPLH Propagation Delay Time 5 300 600
tPHL +TR or -TR to Q or Q 10 150 300 ns
15 100 220
tPLH Propagation Delay Time RL = 1KΩ 5 250 500
tPHL Reset to Q or Q 10 125 250 ns
15 95 190
tWH Minimum Input Pulse Width RL = 1KΩ 5 80 140
tWL +TR, -TR or Reset 10 40 80 ns
15 30 60
tWT Output Pulse Width - Q or Q 5 57 60.6 64.5
(CX = 0.005 µF, RX = 10 KΩ *) 10 55 58.9 63.0 µs
15 55 59.1 63.5
tWT Output Pulse Width - Q or Q 5 9.4 9.97 10.5
(CX = 0.1 µF, RX = 100 KΩ) 10 9.4 9.95 10.6 ms
15 9.5 10.00 10.6
tWT Output Pulse Width - Q or Q 5 0.95 1.00 1.06
(CX = 10 µF, RX = 100 KΩ) 10 0.95 1.00 1.06 s
15 0.96 1.00 1.07
tW Pulse Width Match Between 100 (T − T ) 5 ±1
1 2
Circuits in Same Package:
T1 10 ±1 %
(CX = 0.1 µF, RX = 100 KΩ) 15 ±1
trr Minimum Retrigger Time 5 0
10 0 ns
15 0
CIN Input Capacitance Any 5 7.5 pF
Input
* Minimum RX value = 4 KΩ, minimum CX value = 500 pF

5/14
HCC/HCF4538B

Typical Output Low (sink) Current Characteristics Minimum Output Low (sink) Current Charac-
teristics

Typical Output High (source) Current Charac- Minimum Output High (source) Current Charac-
teristics teristics

Typical Propagation Delay Time as a Function of Typical Propagation Delay TIme as a Function of
Load Capacitance (+TR or -TR to Q or Q) Load Capacitance (RESET to Q or Q)

6/14
 HCC/HCF4538B

Typical Transition Time as a Function of Load Typical Pulse Width Variation as a Function of
Capacitance Supply Voltage

Typical Pulse Width Variation as a Function of Typical Pulse Width Variation as a Function of
Temperature Temeprature

Typical Total Supply Current as a Function of

Output Duty Cycle

7/14
HCC/HCF4538B

Power Down Mode

During a rapid power-down conditiona, as would An alternate protection method is shown in Fig. 2,
occur with a power supply short circuit or with a where a 51 Ω current limit resistor is inserted in
poorly filtered power supply, the energy stored in CX series with CX. Note that a small pulse width de-
could discharge into Pin 2 or 14. To Avoid possible crease will occour however, and RX must be appro-
device damage in this mode, when CX is ≤0.5 micro- priately increased to obtain the originally desired
farad, a aprotection diode with a 1 Ampere or higher pulse width.
rating (1N5395 or equivalent) and a separate
ground return for C X should be provided as shown
in Fig. 1

Figure 1: rapid Power Down Protection Circuit Figure 2: Alternate rapid Power Down Protection
Circuit

8/14
 HCC/HCF4538B

TEST CIRCUITS
Quiescent Device Current. Noise Immunity.

Input Leakage Current.

9/14
HCC/HCF4538B

Plastic DIP16 (0.25) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

a1 0.51 0.020

B 0.77 1.65 0.030 0.065

b 0.5 0.020

b1 0.25 0.010

D 20 0.787

E 8.5 0.335

e 2.54 0.100

e3 17.78 0.700

F 7.1 0.280

I 5.1 0.201

L 3.3 0.130

Z 1.27 0.050

P001C

10/14
 HCC/HCF4538B

Ceramic DIP16/1 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 20 0.787

B 7 0.276

D 3.3 0.130

E 0.38 0.015

e3 17.78 0.700

F 2.29 2.79 0.090 0.110

G 0.4 0.55 0.016 0.022

H 1.17 1.52 0.046 0.060

L 0.22 0.31 0.009 0.012

M 0.51 1.27 0.020 0.050

N 10.3 0.406

P 7.8 8.05 0.307 0.317

Q 5.08 0.200

P053D

11/14
HCC/HCF4538B

SO16 (Narrow) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.004 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8° (max.)

P013H

12/14
 HCC/HCF4538B

PLCC20 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 9.78 10.03 0.385 0.395

B 8.89 9.04 0.350 0.356

D 4.2 4.57 0.165 0.180

d1 2.54 0.100

d2 0.56 0.022

E 7.37 8.38 0.290 0.330

e 1.27 0.050

e3 5.08 0.200

F 0.38 0.015

G 0.101 0.004

M 1.27 0.050

M1 1.14 0.045

P027A

13/14
HCC/HCF4538B

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.

 1994 SGS-THOMSON Microelectronics - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A

14/14