Scribd
Upload
48 views

Assignment On Power System II

This document discusses the main components of overhead power lines and commonly used conductor materials. It identifies the key components as conductors, supports, insulators, cross arms, and miscellaneous items. It then examines various conductor materials including copper, aluminum, steel-cored aluminum, galvanized steel, and cadmium copper. For each material, it provides details on their electrical and mechanical properties and discusses when each material is best suited for overhead power line applications.

Uploaded by

Jahid Hasan
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
48 views

Assignment On Power System II

This document discusses the main components of overhead power lines and commonly used conductor materials. It identifies the key components as conductors, supports, insulators, cross arms, and miscellaneous items. It then examines various conductor materials including copper, aluminum, steel-cored aluminum, galvanized steel, and cadmium copper. For each material, it provides details on their electrical and mechanical properties and discusses when each material is best suited for overhead power line applications.

Uploaded by

Jahid Hasan
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

● Pundra University of Science & Technology

Assignment
Course Name: Power System II
Course code: EEE 435

Submitted by Submitted to
Jahid Hasan. Sagorika khatun
1st batch Lecturer in EEE
7th semester
Roll: 12
ID: 00117109012
Dept: EEE

Main Components of Overhead Lines:


An overhead line may be used to transmit or distribute electric power.
The succcessful operation of
an overhead line depends to a great extent upon the mechanical
design of the line. In general, the main components of an overhead
line are:

1.Conductors; which carry electric power from the sending end station
to the receiving end
station.

2.Supports; which may be poles or towers and keep the conductors at


a suitable level above the
ground.

3. Insulators; which are attached to supports and insulate the


conductors from the ground.

4. Cross arms; which provide support to the insulators.

5. Miscellaneous items; such as phase plates, danger plates, lightning


arrestors, anti-climbing
wires etc.

The continuity of operation in the overhead line depends upon the


judicious choice of above
components. Therefore, it is profitable to have detailed discussion on
them.

8.2 Conductor Materials


The conductor is one of the important items as most of the capital
outlay is invested for it. Therefore,
proper choice of material and size of the conductor is of considerable
importance. The conductor
material used for transmission and distribution of electric power should
have the following properties-
(i) high electrical conductivity.

(ii) high tensile strength in order to withstand mechanical stresses.

(iii) low cost so that it can be used for long distances.

(iv) low specific gravity so that weight per unit volume is small.

Commonly used conductor materials:


The most commonly used conductor materials for over head lines are
copper
aluminium,
steel-cored aluminium,
galvanised steel and
cadmium copper.

The choice of a particular material will depend upon the cost, the
required electrical and mechanical
properties and the local conditions.

1. Copper: Copper is an ideal material for overhead lines owing to its


high electrical conduc-
tivity and greater tensile strength. It is always used in the hard drawn
form as stranded conductor.
Although hard drawing decreases the electrical conductivity slightly
yet it increases the tensile strength considerably.
Copper has high current density i.e., the current carrying capacity of
copper per unit of X-sec-
tional area is quite large. This leads to two advantages. Firstly, smaller
X-sectional area of conductor is required and secondly, the area
offered by the conductor to wind loads is reduced. Moreover, this
metal is quite homogeneous, durable and has high scrap value.
There is hardly any doubt that copper is an ideal material for
transmission and distribution of
electric power. However, due to its higher cost and non-availability, it
is rarely used for these pur-
poses. Now-a-days the trend is to use aluminium in place of copper.
2.Aluminium: Aluminium is cheap and light as compared to copper but
it has much smaller
conductivity and tensile strength. The relative comparison of the two
materials is briefed below:

(i)The conductivity of aluminium is 60% that of copper. The smaller


conductivity of aluminium means that for any particular transmission
efficiency, the X-sectional area of conductor must be larger in
aluminium than in copper. For the same resistance, the diameter of
aluminium conductor is about 1-26 times the diameter of copper
conductor.

The increased X-section of aluminium exposes a greater surface to


wind pressure and, therefore
supporting towers must be designed for greater transverse strength.
This often requires the use of
higher towers with consequence of greater sag.

(ii) The specific gravity of aluminium (2.71 gm/cc) is lower than that of
copper (89 gm/cc).
Therefore, an aluminium conductor has almost one-half the weight of
equivalent copper
conductor. For this reason, the supporting structures for aluminium
need not be made so
strong as that of copper conductor.

(iii)Aluminium conductor being light, is liable to greater swings and


hence larger cross-arms are
required.

(iv) Due to lower tensile strength and higher co-efficient of linear


expansion of aluminium, the
sag is greater in aluminium conductors.

Considering the combined properties of cost, conductivity, tensile


strength, weight etc., aluminium has an edge over copper. Therefore,
it is being widely used as a conductor material. It is particularly
profitable to use aluminium for heavy-current transmission where the
conductor size is large and its cost forms a major proportion of the
total cost of complete installation.
3. Steel cored aluminium: Due to low tensile strength, aluminium
conductors produce greater sag. This prohibits their use for larger
spans and makes thenm unsuitable for long distance transmission. In
order to increase the tensile strength, the aluminium conductor is
reinforced with a core of galvanised steel wires. The composite
conductor Aluminium thus obtained is known as steel cored aluminium
and is abbreviated as A.C.S.R. (aluminium conductor steel
reinforced).
The steel cored aluminium conductors have the following advantages:
i) The reinforcement with steel increases the tensile strength but at the
same time keeps the
composite conductor light. Therefore, steel cored aluminium
conductors will produce smaller
sag and hence longer spans can be used.

(ii) Due to smaller sag with steel cored aluminium conductors, towers
of smaller heights can be
Used.

4. Galvanised steel. Steel has very high tensile strength. Therefore,


galvanised steel conductors can be used for extremely long spans or
for short line sections exposed to abnormally high
stresses due to climatic conditions. They have been found very
suitable in rural areas where cheap-
ness is the main consideration. Due to poor conductivity and high
resistance of steel, such conductors
are not suitable for transmitting large power over a long distance.
However, they can be used to
advantage for transmitting a small power over a small distance where
the size of the copper conductor
desirable from economic considerations would be too small and thus
unsuitable for use because of
poor mechanical strength.

5. Cadmium copper. The conductor material now being employed in


certain cases is copper
alloyed with cadmium. Anaddition of 1% or 29% cadmium to copper
increases the tensile strength by
about 50% and the conductivity is only reduced by 15% below that of
pure copper. Therefore,
cadmium copper conductor can be useful for exceptionally long spans.
However, due to high cost of
cadmium, such conductors will be economical only for lines of small X-
section i.e., where the cost of
conductor material is comparatively small compared with the cost of
supports.

You might also like