0% found this document useful (0 votes)
2K views10 pages

Ibr Acceptable Weld Joint

IBR

Uploaded by

Arindom
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
0% found this document useful (0 votes)
2K views10 pages

Ibr Acceptable Weld Joint

IBR

Uploaded by

Arindom
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 10
Wf) Vindexhemnn Mil Acceptable Weld Joint Home / |B-Pro Information / Acceptable Weld Joint Some Acceptable Weld Joint as per IBR Regulations ISr.No| Type ofJoint | IBR Regulation No. | Design Notes | Figure Butt 125(a) Figure- | Applicable plate thickness 1 welded 48 xi/6 less than 20 mm joint 2 weed 125(a) Applicable plate thickness less * Figure-3 than 20 mm joint 3 | Butt welded joint | x1/3 eigeg | 125(@) Figure- Applicable plate thickness wee 1&XiI/5 above than 20 mm joint idea 125(a) Figure- Applicable plate thickness wee 2&XIN6 above than 20 mm joint Shelltohead butt | Figure- | Outside diameter join 4a match oy Wi Lergamel 2% Pressure side Shelltohead butt | _ Inside diameter Cd join match 7 U8 (1,— 14) 807 NOT LESS THAN 58 me Shelltohead | iq | Dished end thicker than shellcither butt join side Taper joint Le te 1) 97 WoT LSS Shell tohead | xlIN0 | Shell thicker than Dished end. Either butt join side Taper acceptable 10 Nozzle pipe / Shell to WN Flange 28(ix) joint (a) 1h Nozzle pipe / Shell to WN Flange 28(ix) joint (b) 2 Nozzle pipe / Shell to WN Flange 28(ix) joint {c) SMM. MIN. RAD. | \ 13. | Nozzle to shell /Dished end joint- | 365/29 | Set-on Without RF pad xI/93 Nozzle 14 | Nozzletoshell/Dished | 5.6, | Setin Nozzle (Single vee with end joint Without RF pad Back gouge) Full Penetration a 15 | Nozzletoshell/Dishedend | xII/8sD | —Set-in Nozzle (Double joint Without RF pad (8) vee) Full Penetration L NZ VA, 9 2 x] [ pone 1 | Nozletoshell/Dished | yiigiia) | Partial Penetration end joint weld joint a7 | Nozzletoshell /Dished | yujgeis) | Partial Penetration end joint weld joint 18 Nozzle to shell / Dished end xi/85F | Double vee Full joint with RF Pad Penetration Nozzle to shell / Dished end Single vee Full 9 joint with RF Pad xive7 Penetration go | TubetoTubesheet | 6, | Seal weld with light joint expansion 2 Tube to xI/67A | Strength weld with light Tubesheet joint expansion 22 Flange to shell joint 29 SLR. wk SMM. 8 of Icke ty BUT NOT LESS THAN 5 mm te SUT NOT LESS THAN 6 mm ts BUT NOT LESS THAN 6 mm Flange to shell joint 30 a e 2 aa 3 WL = O5¢ te BUT NOT LESS THAN S rm = Bm C= ty BUT NOT LESS THAN 10 mm E BUT NOT LESS THAN 8 mm 24 Flange to shell joint 32 A= 05 ty BUT NOT LESS THEN 5 mm mm MW 5 BUT NOT LESS THEN 10am ‘St, AUT NOT LESS THAN 6 mm 25 | Flange to shell joint | 31 rr 2 3} |e El 8 = ty BUT NOT LESS THAN 5 mm E = 3/2 ts BUT NOT LESS THAN & mm 26 | Flangetoshelljoint | 33 ella [| B= mm E = 3/2 4, BUT NOT LESS THAN 5 mm F = 1 mm We 27 | Flange toshelljoint | 33 WE ARE PROUD TO SAY e° minke Dy ce Contact

You might also like