0% found this document useful (0 votes)
188 views29 pages

Service Manual: HTX29S31S

This document provides a service manual for a color television model HTX29S31S. It contains 15 sections covering contents, product code illumination, features, safety precautions, warnings and cautions, net dimensions, parts and functions, remote controller functions, program diagram, maintenance, circuit diagrams, circuit explanations, adjustments, exploded views, lists of parts, damageable parts, and information on resistors and capacitors. The manual provides technical specifications and safety guidelines for servicing the television.

Uploaded by

Montecarlo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
188 views29 pages

Service Manual: HTX29S31S

This document provides a service manual for a color television model HTX29S31S. It contains 15 sections covering contents, product code illumination, features, safety precautions, warnings and cautions, net dimensions, parts and functions, remote controller functions, program diagram, maintenance, circuit diagrams, circuit explanations, adjustments, exploded views, lists of parts, damageable parts, and information on resistors and capacitors. The manual provides technical specifications and safety guidelines for servicing the television.

Uploaded by

Montecarlo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 29

HTX29S31S

COLOR TELEVISION
Service Manual

MODEL: HTX29S31S

Features
PAL M/N, NTSC M
Front Audio/Video input
V-CHIP, CCD
181 Channel

NO:M-LA-EC-2199-76812 -Edition: 2002.12.30


CONTENTS

CONTENTS

1 Contents--------------------------------------------------------------------1
2 Product Code illumination and Series Introduction--------------------2

3 Features--------------------------------------------------------------------------------3

4 Safety Precautions------------------------------------------------------------------4

5 Warning and Cautions-------------------------------------------------------------5

6 Net dimension----------------------------------------------------------------------11

7 Parts and Functions--------------------------------------------------------------12

8 Remote Controller Functions--------------------------------------------------13

9 Program Diagram------------------------------------------------------------------14

10 Maintenance Service and Trouble shooting------------------------------15

11 Circuit Diagram---------------------------------------------------------------------18

12 Circuit Explanation----------------------------------------------------------------22

13 Adjustment---------------------------------------------------------------------------24

14 Exploded View----------------------------------------------------------------------27

15 List of Parts--------------------------------------------------------------------------28

16 Damageable Parts List-----------------------------------------------------------41

17 Information of Resistors and Capacitors----------------------------------41

1
Product Code illumination and Series Introduction

2.Product Code illumination and Series Introduction

H T - 29 31

Color television appearance

CRT size (unit: inch)

Philips

Haier

2
Features

3.Features
MODEL MODEL
NO. ITEM FUNCTION HS-2190 NO. ITEM FUNCTION TV-9708

1 PICTURE Main IC 76814 24 SOFTWARE Digital curtain


2 CRT Flat square 25 Slow fading on & off
3 Color system NTSC 26 Semitransparent menu
4 Audio system M 27 Non-flashing channel changing
5 Number of channels 181 28 ZOOM
6 OSD language E F S P 29 16:9 mode
7 Multi-picture modes 30 Games
8 AUDIO AV stereo 31 Calendar
9 Super woofer 32 Child-lock
10 Surrounding sound 33 Multi-functional lock
11 Treble/bass boost 34 No-picture listening
12 Left/right balancer 35 Background light
13 NICAM 36 Auto-timer on
14 Multi-audio modes 37 CCD
15 Tone adjuster 38 V-CHIP
16 MTS/SAP 39 PARAMETER Number of built-in speakers 2
17 Auto-volume leveling 40 Audio output power (W) 2
18 JACK AV input Front 1,Side 1 41 Total power input W 140
90VAC-250V
19 42
AV output Voltage range V AC
20 DVD terminal 43 Power frequency Hz 60
21 S-video jack 44 Time of sleep timer (MINS) 120
22 Headphone socket 45 Net weight (KG) 41.5
23 SCART socket 46 Gross weight (KG) 50
770x500x58
47
Net dimension (MM) 0
890x645x64
48
Packaged dimension (MM) 0
49 Quantity for 20' container
50 Quantity for 40' container
51 Quantity for 40' high container

3
Safety Precautions

4. Safety Precautions
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical identify these parts and mechanical parts in this chassis have special safety-related
characteristics! In the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of the manufacturer.
General Guidance
An Isolation Transformer should always be used during the servicing of a receiver whose chassis is
not isolated from the AC power line. Use a transformer of adequate power rating as this protects the
technician from accidents that might result in personal injury caused by electrical shocks.
It will also protect the receiver and it’s components from being damaged by accidental shorts of the
circuitry that might be inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with a specified one.
When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor
10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to the high vacuum and large surface area of the picture tube, extreme care should be taken in
handling the Picture Tube. Do not lift the Picture Tube by its Neck.
X-RAY Radiation
Warning:
The source of X-RAY RADIATION in this TV receiver is the High Voltage Section and the Picture
Tube.
For continued X-RAY RADIATION protection, the replacement tube must be of the same type as
specified in the Replacement Parts List.
Before returning the receiver to the customer,
Always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as
antennas, terminals, etc., to make sure that the set is safe to operate without any danger of electrical
shock.

4
Warning and Cautions

5.Warning and Cautions

1. When you clean the TV set, please pull 4. To prevent the TV set from firing and
out the power plug from AC outlet. Don't electric shock, don't
clean the cabinet and the screen with make the TV set rain
benzene, petrol and other chemicals. or moisture.

2. In order to prolong the using life of the 5. Don't open the back cover, otherwise it is
TV set, please place it on a ventilated possible to damage the components in the
place. TV set and harm you.

3. Don't place the 6. When the TV set isn't going to be used


TV set i n t h e for long time or it is in thunder and
sunshine or near lightening, please pull out the plug from AC
heat source. outlet and the antenna plug from the cover
of the TV set.

Explanation on the display tube

Generally, it is not needed to clean the tube surface. However, if necessary,its surface can be
cleaned with a dry cotton cloth after cutting off the power.Don't use any cleanser. If using hard
cloth, the tube surface will be damaged.

CAUTION: Before servicing receivers covered by this service manual and its supplements and
addenda, read and follow the SAFETY PRECAUTIONS.
5
Warning and Cautions

NOTE: If unforeseen circumstances create conflict between the following servicing precautions and
any of the safety precautions, always follow the safety precautions. Remember: Safety First.
General Servicing Precautions
1). Always unplug the receiver AC power cord from the AC power source before:
a. Removing or reinstalling any component, circuit board module or any other assembly of the
receiver.
b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver.
CAUTION: A wrong substitution part or incorrect installation polarity of electrolytic capacitors
may result in an explosion hazard.
d. Discharging the picture tube anode.
2). Test high voltage only by measuring it with an appropriate high voltage meter or other
voltage-measuring device (DVM, FETVOM, etc.) equipped with a suitable high voltage probe. Do not
test high voltage by “drawing an arc”.

3) .Discharge the picture tube anode only by (a) first connecting one end of an insulated clip lead to
the degaussing or kine aquadag grounding system shield at the point where the picture tube socket
ground lead is connected, and then (b) touch the other end of the insulated clip lead to the picture
tube anode button, using an insulating handle to avoid personal contact with high voltage.
4) .Do not sprays chemicals on or near this receiver or any of its assemblies.
5). Unless specified otherwise in this service manual, clean electrical contacts only by applying the
following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive
applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of contacts is not required.
6). Do not defeat any plug / socket B+ voltage interlocks with which receivers covered by this
service manual might be equipped.
7). Do not apply AC power to this instrument and/or any of its electrical assemblies unless all
solid-state device heat sinks are correctly installed.
8) Always connect the test receiver ground lead to the receiver chassis ground before connecting
the test receiver positive lead.
Always remove the test receiver ground lead last.
9). Use with this receiver only the test fixtures specified in this service manual.
CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.
Electrostatic ally Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such
6
Warning and Cautions

components are usually called Electrostatic ally Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field effect transistors and semiconductor “chip”
components. The following techniques should be used to help reduce the incidence of component
damage caused by static electricity.
1) Immediately before handling any semiconductor component or semiconductor- equipped
assembly, drain off any electrostatic charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available discharging wrist strap device, which should
be removed to prevent potential shock prior to applying power to the unit under test.
2) After removing an electrical assembly equipped with ES devices, place the assembly on a
conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the
assembly.
3) Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4) Use only an anti-static type folder removal device. Some solder removal devices not classified as
“anti-static” can generate electrical charges sufficient to damage ES devices.
5) Do not use freon-propelled chemicals. These can generate electrical charges sufficient to
damage ES devices.
6) Do not remove a replacement ES device from its protective package until immediately before you
are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted
together by conductive foam, aluminum foil or comparable conductive material).
7) Immediately before removing the protective material from the leads of a replacement ES device,
touch the protective material to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety
precautions.
8) Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise even
some normally harmless motions such as mutual brushing of your clothes’ fabric or lifting of your
foot from a carpeted floor might generate static electricity sufficient to damage an ES device.)
General Soldering Guidelines
1) Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will
maintain tip temperature within the range of 500 oF to 600 oF.
2) Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.
3) Keep the soldering iron tip clean and well tinned.
4) Thoroughly clean the surfaces to be soldered. Use a mall wire bristle (0.5 inch, or 1.25cm) brush
with a metal handle. Do not use freon-propelled spay-on cleaners.
5) Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature. (500 o F to 600o F)
b. Heating the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suction-type solder removal device with
solder braid.
7
Warning and Cautions
CAUTION: Work quickly to avoid overheating the circuit board printed foil.
1) Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature. (500 o F to 600o F)
b. First, hold the soldering iron tip and solder the strand against the component lead until the
solder melts.
c. Quickly move the soldering iron tip to the junction of the component lead and the printed
circuit foil, and hold it there only until the solder flows onto and around both the component
lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit board printed foil.
d. Closely inspect the solder area and remove any excess or splashed solder with a small
wire-bristle brush.
Remove /Replacement
Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and
then bent flat against the circuit foil. When holes are of slotted type, the following technique should
be used to remove and replace the IC. When working with boards using the familiar round hole, use
the standard technique as outlined.
Removal
Desolder and straighten each IC lead in one operation by gently prying up on the lead with the
soldering iron tip as the solder melts.
Draw away the melted solder with an anti-static suction-type solder removal device (or with solder
braid) before removing the IC.
Replacement
Carefully insert the replacement IC in the circuit board.
Carefully bend each IC lead against the circuit foil pad and solder it.
Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic
coating to the areas).
“Small-Signal” Discrete Transistor
Removal/Replacement
Remove the defective transistor by clipping its leads as close as possible to the component body.
Bend into a “U” shape the end of each of three leads remaining on the circuit board.
Bend into a “U” shape the replacement transistor leads.
Connect the replacement transistor leads to the corresponding leads extending from the circuit board
and crimp the “U” with long nose pliers to insure metal to metal contact then solder each connection.
Power Output, Transistor Device
Removal/Replacement
Heat and remove all solder from around the transistor leads.
8
Warning and Cautions
Remove the heat sink mounting screw (if so equipped).
Carefully remove the transistor from the heat sink of the circuit board.
Insert new transistor in the circuit board.
Solder each transistor lead, and clip off excess lead.
Replace heat sink.
Diode Removal/Replacement
Remove defective diode by clipping its leads as close as possible to diode body.
Bend the two remaining leads perpendicularly to the circuit board.
Observing diode polarity, wrap each lead of the new diode round the corresponding lead on the
circuit board.
Securely crimp each connection and solder it.
Inspect (on the circuit board copper side) the solder joints of the two “original” leads. If they are not
shiny, reheat them and if necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1) Clip each fuse or resistor lead at top of the circuit board hollow stake.
2) Securely crimp the leads of replacement component around notch at stake top.
3) Solder the connections
CAUTION: Maintain original spacing between the replaced component and adjacent components
and the circuit board to prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that
bonds foil to the circuit board causing the foil to separate from or “lift-off” the board. The following
guidelines and procedures should be followed whenever this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the following procedure to install a jumper
wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).
1) Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper
as absolutely necessary).
2) Carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining
copper pattern.
3) Bend a small “U” in one end of a small gauge jumper wire and carefully crimp it around the IC pin.
Solder the IC connection.
4) Route the jumper wire along the path of the out-away copper pattern and let it overlap the
previously scraped end of the good copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
9
Warning and Cautions

At other connections
Use the following technique to repair the defective copper pattern at connections other than IC Pins.
This technique involves the installation of a jumper wire on the component side of the circuit board.
1) Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to insure that a hazardous condition will not exist if the jumper
wire opens.
2) Trace along the copper pattern from both sides of the pattern break and locate the nearest
component that is directly connected to the affected copper pattern.
3) Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of
the pattern break to the lead of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so that it does not touch components or
sharp edges.

10
Net dimension

6.Net dimension

11
Parts and Functions

7.Parts and Functions

1.Front panel
HT-2599/HP-2999 TV

'
)
"# $

%#"

&
!

TV/AV MENU CH

TV Rear Panel
3
ANT
1
VIDEO RAUDIOL
IN
S-VIDEO AV2

OUT
4

12
Remote Controller Functions

8.Remote Controller Functions

13
Program Diagram

9. Program Diagram
Insert the power plug into the power line socket and insert the antenna plug into the antenna socket
on the rear panel. Press down the power switch of the TV set. The red indicator light goes on.
Program preset
A 1). Auto searching and storing program
Press MENU button on the remote controller to call up the “PREST” menu on the screen. Use the
“ ” key to select the bar “auto search” then press the “ ” to make sure. If you want to stop,
press the key “ ”.
2). Deleting channel number
Press channel up/down buttons to select a channel to skip. Press MENU to call up the “PREST”
menu on the screen. Then Press the” “item to select the bar “Add/Delete”
then use the “ ” key to select Add or Delete.

B Volume tuning
Press VOLUME buttons VOL- to decrease and VOL+ to increase the volume.

C Personal preference settings


Picture modes
Press P.STD repeatedly to change among Personal, Stadard, Vvivid, Soft to change the Picture Mode.

14
. Maintenance service and trouble shooting

10.Maintenance service and trouble shooting


1). Adjustment item Explanation:
OSD Explanation Range Remark
0 H.PHASE H.PHASE 0~31
1 NT.H.PHASE H.PHASE 0~31 No used
2 H.BLK.LEFT 0~7
3 H.BLK.RIGHT 0~7
4 V.SIZE Vertical Size 0~127
5 V.LINE Vertical Linearity 0~31
6 V.POSI Vertical DC 0~63
7 V.SC Vertical S-Correction 0~31
8 NT.V.SIZE Vertical Size -32~+31
9 NT.V.LINE Vertical Linearity -16~+15
10 NT.V.POSI Vertical DC -32~+31
11 NT.V.SC Vertical S-Correction -16~+15

12 RF.AGC RF AGC Delay 0~63


13 VOL.OUT Volume Control 0~127
14 OSD H.POSI 0~127
15 OSD V.POSI 0~31
16 INPUT LEVEL 0~15
17 SPECTRAL 0~63 (0~31)PHILIP IC
18 WIDEBAND 0~63 (0~31)PHILIP IC
19 STEREO VCO 0~63 No used
20 FILTER SET 0~63 No used
21 SAP VCO 0~63 No used

“ ”

γ
γ

“ ”
“ ”
15
.Maintenance service and trouble shooting

Brt.Abl.Def (0/1)
Mid.Stp.Def (0/1)
— R-Y/B-Y Gain Balance (0~15) No use (LA76814)
R-Y/B-Y Angle (0~15)
C_Kill OFF (0/1)
Sound Trap (0~7)
Volume Filter Defeat
Video IF setting (0 45.75M 1 58.75M) For LA76814
Video Level (0~7)
FM Level (0~31)
0 turn TV on twice 1 memory 2 3
Turn TV on first

0 without AV 1 one AV input 2 two AV input 3 Three AV input

No used No used
No used No used
No used No used

NOTHING NOTHING

16
Maintenance Service and Trouble shooting

No lig

Check to see if
Fuse3 is normal
Abnormal
Normal

Check VD501, C507, Check to see 110V 180V


V513, etc. etc. voltage is normal
Normal
Abnormal
Check to see if the Test to see all terminal
collector voltage of V552 Resistance of load
is 0V Is normal

Normal Abnormal Normal Abnormal

Check to see Check the control Check Check to see if


if , 12v, voltage of V552 or power unit rectifying tube
5v is normal CPU power is normal

Normal Abnormal Normal Abnormal

Check N101 The failure of Change Check the


ect horizontal unit or rectifying tube Loader
N551 N552

17
Circuit Diagram

11. Circuit Diagram

18
Circuit Diagram

XS801-2 XS803 XS801-1


AV2 XS802
AVout AV1

V2in

L2in

R2in
L1in

R1in
Lout

Rout

V1in
Vout

Y
C
R825
B3 82
C806
12V 16V10
+
R1010 W801
R1009 R826
4.7K R814 X
47K 4.7K C812
R808 4.7K VHS
0.01
V804 R835 82
R838 2SC1815 68K
82
R823
C811 8.2K
R836 C810 R907
+

C825 R837 16V10 R902


22K C809 16V10 2SJ15K
16V47 1K C807 C808
+
100 V902
+
16V10
+
16V10 16V10 + + R815
4.7K B7 2SC2688
R818 5V
82 C903
CJ56R
R904 VD901 R908
VD801 330
B3 IN4148 1/2SJ2.7K
1N4148 R819
12V
1K R906
C901
470 R917
R820 CJ390
2SJ15K
V802 R831 3.3K
68K + C813
2SC1815

8
16V10 R912
R834 R824

1Y

0Y

1Z

Z COM

OZ

INH

VEE

VSS
82 100 V912
27K V803 2SC2688
R832
+

C823 R833 2SC1815 R918


22K C913
16V47 1K N801 1/2SJ2.7K
R914 CJ56R
330 VD911
TC4053BP/BF
IN4148
R916

Y COM
C804 C911

X COM
470 R927

VDD
B3 B7 0.01 CJ220 2SJ15K

OX
1X

C
A

B
12V 5V
R922
16

15

14

13

12

11

10

9
100 V922
R928
R801 B2 B902 2SC2688
V801 XS602 XP602 1/2SJ2.7K
27K C802 + C801 18V 10W8OHM
2SC1815 TJC3-2A TJC3-2Y
0.01 16V220 C923
R924 CJ56R VD921
W804 R625 330
R802 1N4148
+

R804 C805 R803 1/4W15K R800 + C606 C607 100


100K 220 68K N601 LA4285(R) N602 LA4285(L) 0.01 B901
B7 16V470 35V1000 + C626 C921 R926
680 XS601 XP601 10W8OHM CJ390 470
5V C601 50V1
C602 TJC3-2A TJC3-2Y

GND

GND

GND

GND
VCC

VCC
NFB

OUT

NFB

OUT
VOL

VOL
C803 +
+

EXT

EXT
+

INT

SW

INT

SW
FLI

FLI
16V10 16V10
V821 R822 16V470
2SC1815 R931 V931
4.7K R615 1K 2SA1015

10

10
100 R932 K9N XS901
+ C616 15K TJC2-2A GZS10-2-108
C932 + 11
+

C821 R821 C819 50V1 16V10 W902 JG0034


6
50V1 1K 220 R933 8

+
2.7K 9
R621 C625
25V470 11 10

+
IF C621 1.5K XS403 XP902 6
SCN-5 L901 5 7 1
R718 R611 16V10 SCN-5Y 8

+
C611 B3 10UH R900 R940 U901
B1 2SJ10K 1.5K C615 5 9
16V10 25V/470 12V DJ10K 33 XXXXXXX
132V 10

+
33V 4
+ + C617
N705 B6 5 7 1
C708 C618 0.01 VD620 3
UPC574 50V4.7 R765 1N4148 + C623 C939
B5 R764 22K 50V2.2 VD622 12V
5V R101 22K 2KV1000
B7 33K 1 42 16V100 1N4148 2 R933 C935 +
5V LNA COMB-FILTER + C613
VD612 + C931 1M 250V22 1 2 3 4
5V + C628
+ R746 R763 16V100 1N4148 C627 VD621 1 16V10
C102 5V R104 22K 22K
C101 100 2 41 50V2.2 0.01 1N4148 VD900
16V100 0.01 50/60 V-MUTE FO
RU3Z XP901
B6 R748 R762 VD611 + C622 1 2 3 4
SCL R105 22K 22K
+ C612 SCN-4Y
100 12V 3 40 1N4148 K6D
ALARM AV/TV 16V100 16V100
R735 R761
SDA 22K
10K 4 39
R773 W-VOL AV1
12K R760
NC R103 2.2K
1K R770 5 38
R772 VOL-L AV2 R777 R778 N451
10K 100 C771
R776 R759 8.2K 560 LA7841
AGC
12K KK470 22K V632
+ C103 R102 6 37 B5

NON INPUT
VOL-R MUTE 2SC1815

PUMP OUT
A101 50V2.2 100K
R774 C772 R758 5V + C733 R630

OUTPUT
FSTDC-3WM-5V R775 100 KK470 22K R779 R780 10K
16V/10 R631

INPUT
7 36

VCC2

VCC1
10K 8.2K + C734 560

GND
POWER WOOFER ON/OFF 10K
R757 16V/10
22K V633
8 35 A701 V631
NC SRS ON/OFF 2SC1815

1
R766 HS-0038 R632 2SA1015
100 10K
9 34
GND IR
B5 C455
R756
5V 22K 63V10
10 33 C631 + VD631 C451
C705 XTAL1 NC 35V100 + 4
SW1001 SW1002 SW1003 SW1004 SW1005 SW1006 18P G701 16V/100 1N4148
SW1007 R755
CH+ CH- V+ V- MENU AV/TV AUTO 32K 22K R452 C459
11 32 3
XTAL2 S-VHS 100FK0.1 XS402
VD451 1
L701 R709 R754 TJC2-6A-4T
2
C704 EM01Z 4
39UH 15P 390K 12 31 10K B4
VDD SAFTY R460 1
25V VD452 3
+ C701 C702 R753 + C719 C720 L451 C452 + + C454 1/2DJ180 C458
0.01 22K 1Z75
16V47 13 30 16V47 0.01 18UH 35V2200 R456 100FK0.1 2
R1008 R1007 R1006 R1005 R1004 R1003 R1002 R1001 KEY IN SCL1 C126 C125 R122 50V1 R457
150K 27K 8.2K 4.7K 3.9K 2.7K 1.5K 680 R751 39 18 330 12K 39K
N101 1
14 29 22K 1 8
AFT IN SDA1 VCC LA76812 R451 + C456 + C457 XP402
R708 C703 L121 C453
R749 2 7 2.2K 35V2200
10K 0.01 15UH 1000 R455 50V4.7 TJC2-5Y
15 28 22K GND R744 1 54
NC SCL0 N702 220 C111 R107 AUDIO OUT SIF IN 12K
3 6 R458
R722 R724 R720 R747 SCL 0.01 100 B3 C124 R121
AT24C04 50V1 1K 1K R461A
1.5K 4.7K 10K 16 27 22K 4 5 12V 2 53 1/2DJ120

+
NC SDA0 SDA FM OUT SIF APC FIL
R108 R110 C123
5.6K R453 R459
R723 220 1000 R454
8.2K 17 26 R745 R119 3 52 1SJ1
RESET NC 220 1K PIF AGC SIF OUT 3K 12K + C450 B3
R726 R725 V102 C120
V702 16V100 12V
VD703 270K 330 2SC2216 FK0.022
2SA1015 C729 18 25 4 51
HZ4A2 0.01 + + FILT BLANK Z101 RF AGC EXT AUDIO IN + C136 C139 R127 L441
C714 C713 R742 R743 C112 LBN45U C119
50V1 50V0.47 390 TN2084
50V2.2 50V1 3.3K 3.3K C110 0.01 0.01
19 24 5 50 XS401
0.01

+
CVBS-IN B OUT R111 VIF IN1 VCO FIL 2
R740 R109 82 C140
R727 1K
R728 R731 20 23 4.7K 6 49 470 R441
470 R734 V SYNC G OUT VIF IN2 VCO COIL C441 R491
470 10K 10K 38M 1/2SD1K
R738 T101 200FK0.36 + C444 1FJ2.2
4.7K 2
21 22 B7 7 48 HA6019 160V4.7
H SYNC R OUT 5V GND(IF) VCO COIL
VD1001 R736 L102 C115 C116 R446
TRL-R R721 4.7K 15UH
+
16V100 0.01 8 47 1/4W220K R474 VD474 + C474
V703 10K N701 SCN-4Y
VCC (VIF) APC FIL + C137 1FJ1 EU1 250V22
R729 LC863232-5V57
2SC1815 V704 R201
150K R113 1K 50V0.47
2SC1815 9 46 10
100K FM FIL VIDEO OUT HV

+
R120 C117 R204 R202 9
V705 R730 39K 50V1 1.2K
2SC1815 10K R732 W408 10 45 560K 7
47K 10K AFT OUT BLK STRETCH FIL FOCUS
R114 C118 4
100K C203
0.01 11 44 16V4.7

+
VD704 5

+
DATA INT VIDEO IN R472 VD472 SCREEN
1N4148 C730 R241 C204 1FJ1 EU1 6
470P 100 50V1 B4
12 43
CLOCK VCC (V/C/D) 25V 3
+ C472 +
R242 C205 C206 R270 B1
100 35V100 R471 2
13 42 0.01 16V47 560K 136V 8
6FJ3.9

+
ABL EXT VIDEO IN 1
C212
N501 50V1
B1 14 41 T471
PC817B 1 2 R IN GND (V/C/B)
130V JF0501-21811
TP-H
4 3 15 40 TP-G TEST R232
C503 C505 G IN SEL VIDEO OUT TEST
3 H-PULSE 1/2DJ1.5K
1000KM1000E1000KM1000E C514 R206
0.01 C208 47K
16 39 ABL

+
VD505 T511 B IN ACC FIL
C532 VD503 R512 VD551 C561 G201 C231
BCK-130-01 R205
400KM470S RM11C RM11C 3.3K 10 RU4AM 160V220 R552 4.43M
50V0.47
22K R233 50NP1
3 1/2DJ100K 17 38 10K
BLANK IN XTAL C207
VD506 R551 R243 FK0.01
VD504 R513 + C210
RM11C + C507 1M R515 C515 2SJ22K V553 R555 270 16V/10 R434
2SJ68K 400V0.022 2SC1815 18 37

+
RM11C 250V470 VD513 9 C551 R554 1/2DJ47K VCC (RGB) FSC OUT B1 7W3.3K
1N4148 2KV470 150K + C244 C245 C280 + C434
R514 100 136V
R502 RP551 16V47 0.01 19 36 V432
1 L502 1M C516 160V10
6WK3.9 C504 C506 735504C VD512 B-2K R556 R OUT APC1 FIL 2SC5299
L909 1000KM1000E1000KM1000E EG01C 2KV220 8 B1-ADJ VD561 22K
HZ6C3 V555 R557 L431
LJ0107CHA XS501 R553 20 35 T431 L433
L505 22K
C513 4.7K 2SA1015 G OUT KILLER FLT BCT-11 YC0008 ZZ0003
1 TJC2-2A R503 2KV330 YC0008 VD412
2SJ68K 1 11 21 34 HZ7C1
VD511 L506 C554 R596 R469
EU2 B OUT X-RAY V431
RT501 YC0008 1KV470 10K R244 R412 VD411 2SC2383-O 2W47
00

MZ72-07 R569 R414 C412 + R415 C411 +


V553 2.7K 22 33 10K 50V1 8.2K 25V47 EU1
275/1A R557 3.9K C432 C435
1 12 2SC1815 AKB IN GND (CCD/H)
22K R432 500KK1000 1500MJ8200 C438 VD435
L432
00 VD510 R511 VD554 V554 23 32 J R433 YC0008 1500MJ8200 ERD07-15L
RGP15D + C564 R566

+
V513 EU2 8.2 V OUT OSD CONTRAST 1/2SJ1K
2SB892 + C401 C276
14 25V2200 10K R401 R271 C437
C502 F6656 50V0.47 16V10 150 C433 VD436
2.2K 24 31 400NJ0.033
250HM0.1 + R593 EU2A L301
+

R510 RAMP ALC.FIL VCC (CCD) 500KK3900


R567 C591 C403 C278 + C277
10K 68K C402 16V47 AA36
VD555 1.2K 50V0.47 FK0.47 0.01
L501 13 50V0.22 25 30
5

RU4YX VD509 VCC (H) CLOCK OUT


735504C C512 + C279
FJ470 HZ15C R400 C404 C405
16V220 0.01 0.01 C305
C501 R562 1/4DJ270 26 29 R272 B4
H AFC FIL VCO IREF 3K 25V 25V2.2
250HM0.1 V501 275/2A R593
C509 R509 VD509 C406 R273
+ 35V100 2SA1015 1K 68K
HZ15C B2 R561 FK0.068 1/4DJ4.7K
27 28
L504 + R507 24V 10K H OUT FBP IN R314
R501 V491 R409 R404
+

YC0008 R508 1.5K R413 680 1/2SJ560


6WDJ220K VD508 2SB892 C407 R402 680
VD507 1.5K 10K
1N4148 C532 C565 N551 3.3K
1N4148 R591 50V1
400KM470S 35V2200
N553 1.2K VD592 AN7812 V552
R506
3

AN7805 1N4148 B6 PCC


FJ680 R507 2SC1815 R403 R302 R304 H-W + C306 R313
FU501 C510 C511 C408 R310
FJ1000 1.5K 12V VD401 100K 10K RP301 RP302 35V470 1SJ5.1
T4A250V R504 FJ470 C533 0.22 330K R303 2.7k
400KM2200S IN4148 VD402 270K B-50K B-10K R312
2SJ0.1
3

R408 IN4148 + C301


B5 N552 DJ5.6K
U902 2.2K 35V47 R308
EW0130KB 5V + AN7805 47k
C304 V302
1

RL551 C570 V301


AC220V R545 OMIT-SS--112LM 10V470 FK0.1 2SA1015
B7 C303 2SC1815
50HZ 1/2CK5.6M R301 C315
5V 8.2K FK0.1 1000
LIVE AREA VD553
1N4148
+
C572
10V470
R309
56K V303
R305 R306 R307 D2012
+ C302 1K 39K 2.2K
35V1000 R311 VD301
2.7K 1N4148

HP-2999(LA76812+LC863228A)
Title
NTSC-M PAL-M; PAL-N; C.C.D/V-chip.

Size Document Number Rev


1
LA76812
Date: Saturday, March 08, 2003 Sheet 1 of 1

NO:M-LA-EC-2199-76812 -Edition: 2002.12.30


Circuit Block Diagram

Circuit Block Diagram

Antenna
Sound Power
Amplifier
Picture/Sound IF Amplifier,
Tuner Video and audio signal
Processing,
SAW RGB Output Circuits CRT
and H &V Sync pulse
segregation Horizontal Scan
Output
I2C BUS

Vertical Scan
Output

ROM
Main Processor
Audio/Video In/Out

Infrared Receiver Remote Controller

NO:M-LA-EC-2199-76812 -Edition: 2002.12.30


PCB

21
Circuit Explanation

12. Circuit Explanation

"

! # $ %

! &$' % # $ !(
% ( # $
( & # $ ((

) !

&

* ' ((

+'

,-. !!

, !

! ! /

! (( % ,

% - (

( )
' %

0 '

22
Circuit Explanation

2). N101 LA76812

,& % - .
-1 ( 2 # 3- (
#- , "
-, (
#- ,1 2)4
#- ,1 % &
! #- & % 5 '
% #- , " (
( -1 ( , (
,-. ( ! -)
& !! % 5.,6 %!
" % ( ,
, 6 ! ) & &
( & 7 / &
38 &
*
! - $ " % # & !!
% !( " 7
( &
! ,
% % 2
0 ' 7 9 ( 2
! -66
/ ,6 38 &
* )#- (
,- ( , %
! 0 9 )#-

23
Adjustment

13. Adjustment

f. User Remote controller g.

j. 60MHz double trace oscillograph(2 units)


k. White balance adjustment instrument

Alignment and check:

optimal.

24
Adjustment

Main power adjustment:


Adjustment: Connect voltage meter to +B on main PCB, make +B voltage be 148V±0.3V.

“ ” ”
“ ”
“ ”
“ ”

AGC ALIGNMENT:
Receive a color bar signal, 60dB,NTSC M color bar pattern, and check if there is noise in the picture, if there is
noise, press FACTORY button and enter service mode, adjust RF.AGC value and make the noise just disappear,
press FACTORY button and exit service mode.

White balance adjustment:


Turn TV on, receive white field signal, and make the probe of white balance adjustment instrument touch with
top and bottom of screen fully. Check if values of R, G, B are standard, if not, press “FACTORY” button, make
“B/W BALANCE” menu display on screen, adjust values of R-BIA, G-BIA, B-IA, R-DRV, G-DRV, B-DRV,
make them standard. Press FACTORY button, exit service mode.
OSD I2C bus control (LA76810) Varied range
S-BRI Sub brightness 0-127
R-BIA Red bias 0-255
G-BIA Green bias 0-255
B-BIA Blue bias 0-255
R-DRV Red drive 0-127
G-DRV Green drive 0-15
B-DRV Blue drive 0-127
C.B/W Cross B/W 0-3

FOCUS ALIGNMENT
Receive crosshatch (N system) pattern; Adjust focus-variable resistor on the FBT, make picture is the
sharpest.

25
Adjustment

GEOMETRIC ALIGNMENT:
Receive the monochrome circle pattern (NTSC system);
Check vertical center and horizontal center and H-linearity .if they are not standard, press FACTORY button to
enter service mode, and adjust vertical size, vertical linearity, vertical center, horizontal center, make them
standard.

Alignment parameter table:


Press FACTORY button on service remote controller and enter service mode: 1.Adjustment mode and2.
Setting mode;

26
Damageable Parts List

16. Damageable Parts List


Location Material Code Parts Name Type Qt. (unit) Remark
FU501 0094000150 Fuse T2.5A/250V 1
0094000778 Remote controller HYF-25E 1
A101 0094003734 Tuner ENV56DB4G3 1
R474, R472 0094101006 Resister RF10-1W-1 ±5%-15-C-A 2
R491 0094101008 Resister RF10-2W-3.3 ±5%-20-C-A 1
N551 0094400357 IC L7812CV 1
N801 0094400417 IC TC4053BP 1
N552, N553 0094400450 IC L7805CV 2
RT501 0094400452 Resister PTH451A7R0Q21 1
N101 0094400457 IC LA76814K 1
V432 0094400465 Transistor 2SD1651----B-A 1
N451 0094400470 IC LA7840 1
N702 0094400636 IC CAT24C08P 1
V102 0094400660 Transistor 2SC2216(O)------F 1
N701 0094401090 IC LC863232A-5V57 1

17. Information of Resistors and Capacitors

!"! #$ %&
RESISTORS & CAPACITORS-PARTS NO.CODE
Notes: 1.part numbers are indicated on most mechanical parts.
Please use this part number for parts orders.
2.The unit of resistance is (ohm).K=1000 ,M=1000K
3.The unit of capacitance is F(microfarad). 1pF=10-6 F.

Numbering system of Capacitor


Example
CL42 ----- 17 ---- 50V ---- 2F4 ---- 104 * ---- Z
Type Voltage Value (pF) Tolerance
CL21X ---- 100V ---- 223 * ---- J
Type Voltage Value (pF) Tolerance
CL110X ---- 25V ---- 100 F 20%
Type Voltage Value Tolerance
4 3
* 104 =10 10 223=22 10

Numbering system of resistor


Example
RY17S ---- 2W ---- 390 ---- J ---- 05-E-A
Type Wattage Value( ) Tolerance
RS11 ---- 1/2W ---- 1.8K ---- K
Type Wattage Value Tolerance
44
ABBREVIATION OF PART NAME AND DESCRIPTION
RESISTOR
PART NAME & DESCRIPTION
TYPE ALLOWANCE PART NAME & DESCRIPTION
T Carbon F 1% TYPE ALLOWANCE
S Solid J 5% C Ceramic J 5%
J Metal K 10% T Ceramic K 10%
Y Oxide M 20% L Film L 15%
F Fuse G 2% D Electrolytic M 20%
A Tantalum P +100%-0%
Z +80%-0%
CAPACITOR

Terminal view of transistors

B CB CE E
E C E B CB

KSR1010TA KSC815-YTA
KSR2010TA KSA539-YTA

CE
B
C
EB

2SD18887YD
BC548-CTA KSC2331-YTA

45

You might also like