IMPORTANT

e
Please read carefully before using the MRX Microplate Reader

Rev. A Part No: 99000210

Software Version:

Instrument Nº:
 This document is the copyright of and must not be copied or reproduced in any
form without prior consent.

DYNEX Technologies reserves the right to make technical improvements to this equipment and
documentation without prior notice as part of a continuous program of product development.

This manual supersedes all previous editions.

e
MRX is a trademark of .
®
MRX is a registered trademark of .
® ® ®
Microsoft , Excel , and Windows are registered trademarks of Microsoft Corporation.

Copyright 2007, All rights reserved.

Limitations of Warranty Relating to Software
1. DYNEX Technologies accepts no liability for the maintenance or support of Microsoft
software.
2. DYNEX Technologies accepts no liability for any consequential loss arising from the use of
software on this product outside the scope of the above definition.

Limitations of Use
e
The user of the MRX must follow the specific manufacturer’s assay package insert when modifying
parameters and establishing results calculation methods.
e
The performance characteristics of the MRX have not been established with specific serology or antigen
e
detection assays. The user must evaluate the MRX in conjunction with the specific serology and/or
antigen detection assays. This evaluation must include the establishment of performance characteristics
for the specific assays.
e
Under no circumstances does the MRX have any direct patient contact or perform any therapeutic
patient function.
Specific diagnostic results are not provided by the device. Diagnostic decisions are made only after
independent confirmation by additional methods under the supervision of a qualified professional.

WARNING:
If this equipment is used in a manner not specified by the manufacturer then the
protection provided by the equipment may be impaired.
Before using any decontamination method, except those recommended by the
manufacturer, users should check with the manufacturer that the proposed method will
not damage the equipment.
This page is intentionally left blank.
 Table of Contents

Table of Contents

About This Manual................................................................... 1

Safety Information.................................................................... 3
Symbols...................................................................................... 5
Warning Symbol ........................................................................................ 5
Chapter 1 Features of the Reader.......................................... 7
Chapter 2 Installation and Setup........................................... 9
2.1 Installation.......................................................................................... 11
Unpacking the Reader .......................................................................... 11
The MRXe Back Panel ......................................................................... 12
Voltage Selector Switch ....................................................................... 13
USB Driver Installation........................................................................ 13
The MRXe Front Panel ......................................................................... 15
Fitting the Lamp and Optical Filters .................................................... 15
Switching the Reader On...................................................................... 17
Chapter 3 Maintenance.........................................................20
3.1 Routine Maintenance Procedures ...................................................... 22
3.2 Cleaning ............................................................................................ 23
Autoclaving .......................................................................................... 23
External Painted and Plastic Surfaces .................................................. 23
Filters.................................................................................................... 23
Decontamination .................................................................................. 23
3.3 Repacking the Reader ....................................................................... 24
3.4 Replacing the Lamp .......................................................................... 25
3.5 Changing the Optical Filters ............................................................. 26
Appendix A: Self-Test Diagnostics .......................................28
Self-Test Sample Printouts ...................................................................... 29
Appendix B: Accessories........................................................30
Appendix C: Specifications...................................................32
Software Specifications............................................................................ 32
Hardware Specifications .......................................................................... 32
Performance ............................................................................................. 32
405 to 850nm Wavelength Range ........................................................ 33
340 to 400 Wavelength Range (Option) .............................................. 33
Interface ................................................................................................... 33

e
MRX Microplate Reader User Manual
 Electrical .................................................................................................. 33
Physical/Environmental Conditions......................................................... 35
Index.........................................................................................36

e
ii MRX Microplate Reader User Manual
 About This Manual

About This Manual

This manual has been written for the laboratory technician and describes
e
how to use the MRX Microplate Reader.
With the information in this manual, you can:
• Install the Reader.
• Configure the Reader, using the Setup dialog, to suit your particular needs.
• Connect the Reader to a PC (personal computer).
• Perform basic maintenance procedures.
This manual also describes all the features and specifications of the
Reader hardware and software.
Information on how to use the Revelation software is included.
For explanations of error messages and possible solutions, refer to the
included Troubleshooting Guide.

Note: Manual updates available at www.DynexTechnologies.com

e
MRX Microplate Reader User Manual 1
 This page is intentionally left blank.

e
2 MRX Microplate Reader User Manual
 Safety Information

Safety Information

If there is any doubt or concern about the safety of the instrument,

contact an approved service center.
Warning: Although this instrument is fully insulated and earthed (grounded), it is
Electric important for all users to be aware of the potential hazard of using liquids
Shock in close proximity to an electrical supply. If any liquids are spilled,
Hazard disconnect the instrument from the mains electrical supply immediately
and clean the liquid up. DO NOT reconnect the electrical supply until the
instrument has been fully inspected by an approved service engineer.
Take care when using non-rigid, non-standard microplates as spillages
are more likely to occur.
To switch this instrument off, press the power switch on the front panel.
Remove the mains power cable from the socket on the rear panel.
Warning: Operating this equipment in ways other than detailed in this manual may
Incorrect impair the protection provided by the instrument.
Operation • DO NOT operate this equipment with the covers removed as potentially
lethal voltages are contained within.
• DO NOT operate this equipment with the safety earth (ground)
disconnected.
• DO NOT install spare components or accessories as this may impair the
safety of the Reader and will invalidate its warranty.
• DO NOT place any objects, or stand within 150mm of the front of the
Reader as this will obstruct the plate carrier.
• DO NOT overfill the microplate wells as this may lead to liquid
contamination of the wells and impair the safety of the Reader.
• BE PREPARED for unexpected plate carrier movement.
• MAKE SURE that the voltage ratings on the rear panel of the Reader
correspond to the local mains supply.

e
MRX Microplate Reader User Manual 3
Safety Information

• MAKE SURE that the mains power cable is correctly wired. Color codes
are as follows:
Europe United States
Brown Live Black Live
Blue Neutral White Neutral
Green/yellow Earth (ground) Green Ground

Fuses The instrument does not contain any user-replaceable internal fuses.

e
4 MRX Microplate Reader User Manual
 Symbols

Symbols

Warning Symbol
For your safety the Reader is marked with a warning symbol to remind
you of certain hazards:

!
• On the back panel: this indicates that the optics door may be hot. If you
want to remove the optics door, make sure that you allow the Reader to
cool before touching it.
• Adjacent to the mains outlet: This indicates that the line voltage switch
must be correctly set before plugging the unit into an outlet. This also
indicates that the auxilliary outlet has a power rating of up to 120VA and an
earth leakage current of less than 1 mA at 264V and 60 Hz.

e
MRX Microplate Reader User Manual 5
 This page is intentionally left blank.

e
6 MRX Microplate Reader User Manual
 Chapter 1 Features of the Reader

Chapter 1 Features of the Reader

e
The MRX Microplate Reader is a microprocessor-controlled
photometer. It is designed to measure the optical density (OD) of fluid
samples in 96-well microplates in order to determine the results of
chemical reactions.

e
Figure 1 MRX Microplate Reader
A full list of the Reader’s technical specifications can be found in
Appendix C.
The Reader provides the following features:
• Revelation software capable of detecting Endpoint, Agglutination and
Kinetic assays
• PC-compatibility for control and data storage
• Single, dual, and multi-wavelength reading modes
• Selection of up to six filter wavelengths
• Data analysis and presentation as OD matrices and/or graphics using curve
fitting routines
• Data output to a PC
• Verification Plate option

e
MRX Microplate Reader User Manual 7
Chapter 1 Features of the Reader

• Temperature Control option

e
8 MRX Microplate Reader User Manual
 Chapter 2 Installation and Setup

Chapter 2 Installation and Setup

2.1 Installation.......................................................................................... 11
Unpacking the Reader .......................................................................... 11
The Reader Back Panel ........................................................................ 11
Voltage Selector Switch ....................................................................... 13
USB Driver Installation........................................................................ 13
The Reader Front Panel........................................................................ 15
Fitting the Lamp and Optical Filters .................................................... 15
Switching the Reader On...................................................................... 17
Self-Tests……………………………………………………..…...…….…………11

e
MRX Microplate Reader User Manual 9
Chapter 2 Installation and Setup

This page is intentionally left blank.

e
10 MRX Microplate Reader User Manual
 Chapter 2.1 Installation

2.1 Installation
CAUTION DO NOT connect the instrument to the mains electrical supply or
switch it on before you have completed this installation procedure.

Unpacking the Reader

The Reader is packed to provide maximum protection during shipment.

Take care when unpacking it and examine it carefully for any damage.
Report any damage to the carrier immediately. Check the contents
against the Instrument Configuration Report enclosed and report any
omissions to your supplier.
Remove the Reader from the carton and place it on a level surface free of
dust, moisture, vibration, drafts, and away from direct sunlight.
(Retain the packing materials in case future transport is required.)

3
2
4

6
7

Figure 2. Packing Contents Example

1 Reader 5 Software CD
2 User CD 6 Power Cord
3 Optical Filters 7 USB Interface Cable
4 Lamp

e
MRX Microplate Reader User Manual 11
Chapter 2.1 Installation

e
The MRX Back Panel

4 7 9

1 5

2 3

e
Figure 3. The MRX Back Panel
1 Mains Inlet 6 Optics Cooling Vents
2 Voltage Selector 7 Serial Number Plate
(See the Voltage Selector
section below)
3 Aux Mains Socket 8 PSU Cooling Vents
4 USB Port 9 Main Enclosure
5 Optics Door

1. The warning symbols on the back panel indicate that

Notes: the optics door may be hot, and that no appliances
other than a monitor should be plugged into the mains
outlet. For more details, refer to the discussion on
Symbols earlier in this manual.
2. Remove the protective foam packing from inside the
optics chamber.

e
12 MRX Microplate Reader User Manual
 Chapter 2.1 Installation

Voltage Selector Switch

The position of the voltage selector switch (see Figure 3) is very
important and must be adjusted to match the line voltage of the mains
power supply before switching the Reader on.
Position of Voltage Selector Mains Line Voltage
115V 100-120V
230V 200-240V
CAUTION: FAILURE TO FOLLOW THE PROCEDURES DETAILED
BELOW MAY RESULT IN DAMAGE TO THE MICROPLATE
READER DUE TO PARTS FALLING INTO THE POWER
SUPPLY.
Voltage selector switch:
• If the voltage selector is not in the correct position, insert a suitable small
flat-bladed screwdriver through the slot in the clear plastic cover and move
the selector to the desired voltage. DO NOT LOOSEN THE SCREWS
USED TO RETAIN THE PLASTIC COVER.

USB Driver Installation

The Reader requires the installation of a USB driver which emulates a standard
RS-232 COM port on the control computer. The port is then referred to as a
Virtual Com Port (VCP).

To start the installation process open the file USB Driver and VCP Install
Procedure located on the supplied User CD. Follow the procedure through to
its completion before continuing.

e
MRX Microplate Reader User Manual 13
Chapter 2.1 Installation

e
14 MRX Microplate Reader User Manual
 Chapter 2.1 Installation

e
The MRX Front Panel

3 2 1

Figure 4. The MRXe Front Panel

1 Power Switch (marked I/O for
on/off)
2 Power Light
3 Plate Carrier Door

Fitting the Lamp and Optical Filters

Warning: Disconnect the mains cable before fitting lamp and filters.

Note: DO NOT touch the filters, lamp or reflector directly.

1. Using a Phillips screw driver, remove the optics door and, if fitted,
remove the packing materials from the optics chamber.
2. Slide the optics assembly out of the instrument.
3. Insert the lamp into the assembly and plug the connector onto the
lamp pin contacts (see Figure 5).
For Osram type lamps:
Make sure that the lamp is seated correctly with the locating pip on
the lamp fitted into the notch on the optics assembly.

e
MRX Microplate Reader User Manual 15
Chapter 2.1 Installation

For Philips type lamps:

Make sure that the lamp is seated correctly and that the lamp pins are
horizontal as shown in Figure 5.

Figure 5 Fitting the Lamp and Filters

1. Insert the filters into the filter wheel.

• Place the filter with the lowest wavelength in position 1, the next
lowest in position 2 and so on.
• Make sure the side of the filter that has the shorter distance from the
groove to the end is toward the lamp.
• Fit filter blanks into all unoccupied positions.
• Make sure that the retaining springs grip the filter casing and are not
bent forwards over the edge of the casing.
2. The Filter Blanks must be fitted into the unoccupied filters positions
in the Filter Wheel.
3. Make sure the Filter Springs are around the sides of the Filter as
shown in Figure 6. The Springs must not extend past the rear face of
the Filter as shown in Figure 7. Otherwise, the self-test will fail due to
“Filter Motor Errors.”

Figure 6 Correct Filter Spring Positioning (view of Filter Wheel from filter
spring side)

e
16 MRX Microplate Reader User Manual
 Chapter 2.1 Installation

Figure 7 Incorrect Filter Spring Positioning

4. Slide the optics assembly back in, attach the lamp connector to the
lamp, and replace the optics chamber door.

Switching the Reader On

Before switching the Reader on, note the position of the voltage selector
(see Figure 3). The position of the selector is very important and must be
adjusted to match the line voltage of the mains power supply.
Position of Voltage Selector Mains Line Voltage
115V 100-120V
230V 200-240V
If the voltage selector is not in the correct position, refer to the Voltage
Selector discussion on page 13.
DO NOT place any objects, or stand within 150mm of the front of
the Reader as this will obstruct the plate carrier.
1. Make sure that the instrument is switched OFF. The power switch is ON
when it is flush with the front panel and OFF when it stands out from the
panel.
2. Insert the power cord supplied into the socket at the rear of the instrument.
3. Connect the power cord to a suitable power source with a protective earth
(ground).
4. Connect the supplied USB cable to the MRXe and the personal computer
used to control the reader.
5. Switch the Reader on by pressing the power switch on the front panel.
6. Power up the computer and install the Revelation operating program by
running the file SETUP.EXE located on the disk.

e
MRX Microplate Reader User Manual 17
Chapter 2.1 Installation

Self-Tests
When the Revelation program starts on the computer the unit carries out
several self-tests to check that the instrument is working correctly.
Appendix A shows a list of these tests and a sample printout.
If the Reader fails any of the tests, an error message is displayed. If the
software can not communicate with the Reader it will request the unit’s
serial number (this can be found on the Reader’s back panel). Double
check the cable connection between the Reader and the PC. If an error
message persists, contact the service center.

e
18 MRX Microplate Reader User Manual
 Chapter 2.1 Installation

This page is intentionally left blank.

e
MRX Microplate Reader User Manual 19
Chapter 3 Maintenance

Chapter 3 Maintenance
3.1 Routine Maintenance Procedures ...................................................... 22
3.2 Cleaning ............................................................................................ 23
Autoclaving .......................................................................................... 23
External Painted and Plastic Surfaces .................................................. 23
Filters.................................................................................................... 23
Decontamination .................................................................................. 23
3.3 Repacking the Reader ....................................................................... 24
3.4 Replacing the Lamp .......................................................................... 25
3.5 Changing the Optical Filters ............................................................. 26

e
20 MRX Microplate Reader User Manual
 Chapter 3 Maintenance

This page is intentionally left blank.

e
MRX Microplate Reader User Manual 21
Chapter 3 Maintenance

IMPORTANT
The first section in this manual contains safety information for all
the equipment in the system. You should be familiar with this
information anyway, but if not, you must read through this
section before carrying out any maintenance.
The warranty on the Reader may become void if you do not
follow the safety and maintenance instructions contained in this
manual, or if the covers are removed by anyone other than
approved service personnel.

3.1 Routine Maintenance Procedures

The Reader requires very little maintenance, however, certain simple
procedures should be carried out on a regular basis.
On a daily basis:
• Verify self-test passes.
• Remove any microplate from the plate carrier, wipe the plate carrier with a
lint-free cloth, and return it to the In position.
• Wipe the external surfaces. Section 4.2 contains more detailed cleaning
instructions.
On a weekly basis:
• Review the results of the self-test that occurs when you switch the Reader
on to make sure the instrument is functioning correctly. If you want to
retain this information for your records, print out the self-test results (see
Appendix A for a sample) or save them to a file.
On a yearly basis:
• Remove the filters and clean them. Section 3.2 contains more detailed
cleaning instructions.
Periodic maintenance should be determined by the user depending upon
location and environmental conditions.

e
22 MRX Microplate Reader User Manual
 3.1 Routine Maintenance Procedures

3.2 Cleaning
Warning: Always switch the instruments off and disconnect the power cable
before cleaning the Reader.
The Reader is constructed from high quality materials, nevertheless spilt
saline solutions, solvents, acids or alkaline solutions must be removed
from outer surfaces immediately to prevent damage.

Autoclaving
DO NOT autoclave any part of this instrument.

External Painted and Plastic Surfaces

Clean external surfaces with a mild laboratory detergent, followed by
10% bleach or 70% alcohol. Always dilute detergents according to the
manufacturer's instructions.

Filters
Clean the filters by wiping them with a lint-free cloth or a lens tissue. If
necessary a little alcohol may be used with the cloth or tissue.

Decontamination
If you need to return the Reader to the service center, and it has been in
contact with human blood, other potentially infectious body fluids,
pathological samples, toxic or radioactive materials, it must be
decontaminated.
Before shipping the instrument, do the following:
• Clean the surface with a mild laboratory detergent followed by 10%
bleach.
• Fill out an Equipment in Transit form (refer to Appendix B for a
copy of the form).

e
MRX Microplate Reader User Manual 23
3.2 Cleaning

3.3 Repacking the Reader

This procedure assumes that the original Reader packaging materials are
being used. Figure 8 summarizes the repacking instructions.
1. Remove the optics chamber door and take out the lamp and filters.
When you replace the optics chamber door, insert the optics chamber
packing materials.
2. Pack the lamp and each of the filters separately.
3. Make sure that there is no microplate in the plate carrier.
4. Place the Reader in the original anti-static plastic bag.
5. Place the bottom end caps into the carton and lower the Reader into the
carton. Fit the top end caps to the Reader.
6. Place the filters and lamp in the accessories box and fit this between the
end caps.
7. Seal the box carefully and securely. Make sure that the box is not
dropped or handled in a rough manner.

Figure 8 Repacking the Reader

e
24 MRX Microplate Reader User Manual
 3.3 Repacking the Reader

3.4 Replacing the Lamp

Warning: If the Reader has been used recently, the optics chamber door and
the lamp in the optics assembly may still be hot. Allow time for these
components to cool before handling. Take care when removing the
optics chamber door as there may be glass from a possibly broken
lamp in the optics assembly.
Figure 9 summarizes the lamp replacement instructions.

Note: DO NOT touch the lamp or reflector with bare fingers.

1. 1Switch off the mains power supply and disconnect the cable.
2. 2Using a Phillips screw driver remove the optics door.
3. Slide the optics assembly out of the instrument.
4. Detach the lamp from the assembly and replace with a new one. Make
sure that the lamp is seated correctly and connected.
5. Slide the optics assembly back into the Reader chassis.
6. Replace the optics chamber door and reconnect the power supply.

Figure 9 Replacing the Lamp

e
MRX Microplate Reader User Manual 25
3.5 Changing the Optical Filters

3.5 Changing the Optical Filters

Warning If the Reader has been used recently, the optics chamber door and
the lamp in the optics assembly may still be hot. Allow time for these
components to cool before handling. Take care when removing the
optics chamber door as there may be glass from a possibly broken
lamp in the optics assembly.
See Figure 10.

Note: DO NOT touch the filters, lamp or reflector with bare fingers.
1. Switch off the power supply and disconnect the mains cable.
2. Using a Phillips screw driver remove the optics door.
3. Slide the optics assembly out of the instrument.
4. Remove the relevant filter from its position in the filter wheel, and
replace with the new one.
• Make sure the side of the filter that has the shorter distance from the
groove to the end is toward the lamp.
• Make sure the Filter Springs are around the sides of the Filter as shown in
Figure 6 on page 14. The Springs must not extend past the rear face of
the Filter as shown in Figure 7 on page 15. Otherwise, the self-test will
fail due to “Filter Motor Errors.”
5. Slide the optics assembly back into the Reader chassis.
6. Replace the optics chamber door and reconnect the power supply.

Figure 10 Changing the Optical Filters

e
26 MRX Microplate Reader User Manual
 3.5 Changing the Optical Filters

This page is intentionally left blank.

e
MRX Microplate Reader User Manual 27
Appendix A: Self-Test Diagnostics

Appendix A: Self-Test Diagnostics

On power up and (optionally) before every read, the Reader performs

several self-tests. These cover:
A/D Status • Begins conversion and checks that the status line
goes high and low.
• Verifies that hardware can be detected and chosen.
Plate Motor • Moves the plate to Out position and then to the In
position.
• Verifies that the plate carrier position sensors are
operating correctly.
• Checks motor and sensors.
Background • Checks for light leakage into the reading
Light compartment.
Lamp • Verifies that current is flowing through the lamp
when it is switched on.
• Checks that the lamp has not blown.
Filter Motor • Moves the filter motor to the first position.
• Checks the filter motor and optical alignment.
Transmission • Verifies that all fibers are capable of transmitting
Levels at least 33% of the maximum transmission level.
• Checks for blocked channels or broken diodes.
Filters • Checks that gains can be selected for all filters.
• Checks for damaged or missing filters.

e
28 MRX Microplate Reader User Manual
 Appendix A: Self-Test Diagnostics

Self-Test Sample Printouts

SELF-DIAGNOSTIC SEQUENCE

Reader Serial # 2CXC2549 Technologist: . .

. ..

Date : 3/17/98
Time : 11:15:02 AM

Test 1 : A/D Pass

Test 2 : Plate motor Pass
Test 3 : Background light levels Pass
Test 4 : Bulb Pass
Test 5 : Filter motor Pass
Test 6 : Transmission levels Pass
Test 7 : Filters Pass

Self-Diagnostic Summary

Reader Status : Ready

e
MRX Microplate Reader User Manual 29
Appendix B: Accessories

Appendix B: Accessories

Description DYNEX Technologies

Part Number
Cable, USB type A-B 50600167
US Power Cord 6090405009
Euro Power Cord 6090405008
Asia/Aust. Power Cord 575100900
Filter 340nm 6329780340
Filter 405nm 6329780405
Filter 450nm 6329780450
Filter 490nm 6329780490
Filter 540nm 6329780540
Filter 550nm 6329780550
Filter 620nm 6329780620
Filter 630nm 6329780630
Lamp (UV) 549000600
Dust Cover 9119780011
Lens Cleaning Cloth 41000070
Service Manual 99000500
Verification Test Plate kit (non UV) 0119780004

e
30 MRX Microplate Reader User Manual
 Appendix B: Accessories

e
MRX Microplate Reader User Manual 31
Appendix C: Specifications

Appendix C: Specifications

Software Specifications
e Standard: Revelation MRX Program
MRX

Hardware Specifications
No. of filters 6

Performance
Read cycle time Single Wavelength: < 4 seconds
Dual Wavelength: < 6 seconds

e
32 MRX Microplate Reader User Manual
 Appendix C: Specifications

405 to 850nm Wavelength Range

Dynamic range -0.100 to +4.000 OD
Linearity† 0.000 to 2.000 OD: ± 1.0%
2.001 to 3.500 OD: ± 1.5%
Filter band width (FWHM) 10 nm ± 2 nm
Center Wavelength Accuracy ± 2 nm
Precision* 0.000 to 2.000 OD: 0.2% CV or 0.005 OD
whichever is greater
2.001 to 3.000 OD: 0.6% CV
3.001 to 3.500 OD: 1.0% CV
Accuracy 0.000 to 3.500 OD: 2.5% or 0.005 OD
whichever is greater

340 to 400 Wavelength Range (Option)

Dynamic range -0.100 to +3.000 OD
Linearity† 0.000 to 2.500 OD: ± 2.0%
Filter band width (FWHM) 18nm ± 2 nm
Center Wavelength Accuracy ± 2 nm
Precision* 0.000 to 2.000 OD: 0.6% CV or 0.005 OD
whichever is greater
2.001 to 2.500 OD: 1.0% CV

† Linearity is the maximum percentage deviation of a reading from the ideal straight
line plot of OD versus concentration. (Measured by the manufacturer at 410nm in the
visible range and 340nm in the UV range).
* Precision is the mean Coefficient of Variation (CV) figure for all wells on a plate that
has been read 20 times in succession. (Measured by the manufacturer at 410nm in the
visible range and 340nm in the UV range).

Interface
Computer Interface USB 1.0/2.0 compatible

Electrical
Light source 75W tungsten halogen lamp

e
MRX Microplate Reader User Manual 33
Appendix C: Specifications

Mains input 100 to 120V or 200 to 240V

50 to 60 Hz (switch selectable)
Power consumption 175 VA
Fuses There are no internal user-replaceable
fuses. The power supply contains a CSA
approved 20x5mm, 4A cartridge fuse with
a voltage rating of 250V in the primary
circuit. If the fuse blows, contact the
service center.
Mains Power Fuse 5A
(U.K. mains
plug/powercord)
Safety Class I apparatus

e
34 MRX Microplate Reader User Manual
 Appendix C: Specifications

Physical/Environmental Conditions
Weight 10.kg (22.lb)
Dimensions D390 x W360 x H220 mm
(15.4 x 14.2 x 8.7 inches)
Operating Temperature 10 – 40°C
Operating Humidity 10 – 90% RH
Storage Temperature 0 – 50°C
Storage Humidity 10 – 90% RH
Altitude < 2000m

e
MRX Microplate Reader User Manual 35
Appendix C: Specifications

Index

e
MRX
—A— back panel, 12
Accessories, 29
—O—
—B— Optical filters
changing the, 25
Back Panel, 12 Optical Filters
fitting the, 14–16
—C—
Cleaning, 22 —R—
Reader
—D— accessories, 29
electrical specifications, 32
Decontamination, 22 features of, 7–8
hardware specifications, 31
interface, 32
—E— performance specifications, 31–32
Electric Shock Hazard, 3 physical/environmental conditions, 34
Equipment in Transit form (decontamination). repacking the, 23
See Appendix B self-tests, 17
software specifications, 31
External Painted and Plastic Surfaces
switching it on, 16
cleaning the, 22
unpacking the, 11
Repacking the Reader, 23
—F—
Filters —S—
cleaning the, 22
Safety Information, 3–4
Front Panel, 14
Self-tests, 17, 27
Fuses, 4
sample printout, 28
Specifications
—I— electrical, 32
hardware, 31
Incorrect Operation, 3 interface, 32
performance, 31–32
—L— physical/environmental, 34
software, 31
Lamp
fitting the, 14–16
replacing the, 24
—V—
Voltage Selector, 13
—M—
Maintenance, 21–22 —W—
Microplate Reader. See Reader. Warning Symbol, 5
e
MRX
front panel, 14

e
36 MRX Microplate Reader User Manual