ELECTRICAL

BCS
A

B
SECTION
BODY CONTROL SYSTEM C

E
CONTENTS
SERVICE INFORMATION ............................ 2 BCM Terminal Arrangement ....................................10 F
Terminal and Reference Value for BCM ..................11
PRECAUTIONS ................................................... 2 BCM Power Supply and Ground Circuit Inspection
Precaution for Supplemental Restraint System ....15 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- CONSULT-III Function (BCM) .................................16
SIONER" ................................................................... 2 CAN Communication Inspection Using CON-
SULT-III (Self-Diagnosis) .........................................17
BCM (BODY CONTROL MODULE) .................... 3 H
Configuration ...........................................................18
System Description ................................................... 3 Removal and Installation of BCM ............................18
CAN Communication System Description ................. 7
Schematic ................................................................. 8 I

BCS

Revision: October 2008 BCS-1 2009 Versa

 PRECAUTIONS
< SERVICE INFORMATION >
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000004306832

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Revision: October 2008 BCS-2 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
BCM (BODY CONTROL MODULE)
A
System Description INFOID:0000000004306833

BCM (body control module) controls the operation of various electrical units installed on the vehicle. B
BCM FUNCTION
BCM has a combination switch reading function for reading the operation of combination switches (light, wiper,
washer, turn signal) in addition to the function for controlling the operation of various electrical components. C
Also, it functions as an interface that receives signals from the front air control, and sends signals to ECM
using CAN communication.
COMBINATION SWITCH READING FUNCTION D
1. Description
• BCM reads combination switch (light, wiper) status, and controls various electrical components accord-
ing to the results. E
• BCM reads information of a maximum of 20 switches by combining five output terminals (OUTPUT 1-5)
and five input terminals (INPUT 1-5).
2. Operation description F
• BCM activates transistors of output terminals (OUTPUT 1-5) periodically and allows current to flow in
turn.
• If any (1 or more) of the switches are turned ON, circuit of output terminals (OUTPUT 1-5) and input ter-
minals (INPUT 1-5) becomes active. G
• At this time, transistors of output terminals (OUTPUT 1-5) are activated to allow current to flow. When
voltage of input terminals (INPUT 1-5) corresponding to that switch changes, interface in BCM detects
voltage change and BCM determines that switch is ON. H

BCS

O
SKIB7592E

3. BCM - Operation table of combination switch P

• BCM reads operation status of combination switch by the combination shown in the following table.

Revision: October 2008 BCS-3 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >

SKIB7614E

NOTE:
Headlamp has a dual system switch.

4. Example operation: (When lighting switch 1st position is turned ON)

• When lighting switch 1st position is turned ON, contact in combination switch turns ON. At this time if
OUTPUT 4 transistor is activated, BCM detects that voltage changes in INPUT 5.
• When OUTPUT 4 transistor is ON, BCM detects that voltage changes in INPUT 5, and judges lighting
switch 1st position is ON. Then BCM sends tail lamp ON signal to IPDM E/R using CAN communication.
• When OUTPUT 4 transistor is activated again, BCM detects that voltage changes in INPUT 5 and rec-
ognizes that lighting switch 1st position is continuously ON.

SKIB7615E

NOTE:
Each OUTPUT terminal transistor is activated at 10ms intervals. Therefore, after a switch is turned ON,
electrical loads are activated with a time delay. But this time delay is so short that it cannot be noticed.
5. Operation mode
• Combination switch reading function has operation modes as follows:
Revision: October 2008 BCS-4 2009 Versa
 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Normal status
• When BCM is not in sleep status, OUTPUT terminals (1-5) each turn ON-OFF every 10ms. A
Sleep status
• When BCM is in sleep mode, transistors of OUTPUT 1 and 5 stop the output, and BCM enters low-cur-
rent-consumption mode. OUTPUTS (2, 3, and 4) turn ON-OFF at 60ms intervals, and receives lighting
B
switch input only.

PKIB6124E

CAN COMMUNICATION CONTROL J

CAN communication allows a high rate of information through the two communication lines (CAN-L, CAN-H)
connecting the various control units in the system. Each control unit transmits/receives data, but selectively
reads required data only. BCS

BCM STATUS CONTROL

BCM changes its status depending on the operation status in order to save power consumption. L
1. CAN communication status
• With ignition switch ON, CAN communicates with other control units normally.
• Control by BCM is being operated properly. M
• When ignition switch is OFF, switching to sleep mode is possible.
• Even when ignition switch is OFF, if CAN communication with IPDM E/R and combination meter is
active, CAN communication status is active.
N
2. Sleep transient status
• This status shuts down CAN communication when ignition switch is turned OFF.
• It transmits sleep request signal to IPDM E/R and combination meter.
• Two seconds after CAN communication of all control units stops, CAN communication switches to inac- O
tive status.
3. CAN communication inactive status
• With ignition switch OFF, CAN communication is not active. P
• With ignition switch OFF, control performed only by BCM is active.
• Three seconds after CAN communication of all control units stops, CAN communication switches to
inactive status.

4. Sleep status
• BCM is activated with low current consumption mode.
• CAN communication is not active.

Revision: October 2008 BCS-5 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
• When CAN communication operation is detected, it switches to CAN communication status.
• When a state of the following switches changes, it switches to CAN communication state:
- Ignition switch
- Key switch (without Intelligent Key)
- Key switch and ignition knob switch (with Intelligent Key)
- Hazard switch
- Door lock/unlock switch (with power door locks)
- Front door switch (LH, RH)
- Rear door switch (LH, RH)
- Back door lock assembly (Hatchback)
- Trunk key cylinder switch (Sedan)
- Trunk lamp switch and trunk release solenoid (Sedan)
- Combination switch (passing, lighting switch 1st position, front fog lamp)
- Keyfob (lock/unlock signal) (with power door locks)
- Front door key cylinder switch LH
• When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.
• Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY
• Power door lock system (with power door locks). Refer to BL-23, "System Description" .
• Remote keyless entry system. Refer to BL-58, "System Description" .
• Power window system (with power windows). Refer to GW-19, "System Description" . NOTE
• Sunroof system (with sunroof). Refer to RF-11, "System Description". NOTE
• Room lamp timer. Refer to LT-91, "System Description" .
• Rear wiper and washer system (Hatchback). Refer to WW-25, "System Description" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
• Panic system. Refer to BL-58, "System Description" .
• Vehicle security (theft warning) system. Refer to BL-219, "System Description" .
• NVIS(NATS) system. Refer to BL-248, "System Description" .
• Headlamp, tail lamp and battery saver control systems. Refer to LT-73, "System Description", LT-4, "System
Description" or LT-25, "System Description" .
• Front fog lamp (with front fog lamps). Refer to LT-39, "System Description" .
• Front wiper and washer system. Refer to WW-3, "System Description" .
• Rear window defogger system. Refer to GW-51, "System Description" .
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER
• Warning chime. Refer to DI-42, "System Description" .
• Turn signal and hazard warning lamps. Refer to LT-48, "System Description" .
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT (WITH INTELLIGENT KEY)
• Intelligent Key system. Refer to BL-88, "System Description" .
MAJOR COMPONENTS AND CONTROL SYSTEM

System Input Output

• All door locking actuators
Remote keyless entry system (with Remote keyless entry receiver
• Turn signal lamp (LH, RH)
power door locks) (keyfob)
• Combination meter (turn signal lamp)
• All door locking actuators
Intelligent Key system (with Intelligent
Intelligent Key unit • Turn signal lamp (LH, RH)
Key)
• Combination meter (turn signal lamp)
Power door lock system (with power Front power door lock/unlock
All door locking actuators
door locks) switch (LH, RH)
Power supply (IGN/RAP) to power
Ignition retained power supply Power supply to power window and sunroof system
window (with power windows)
Power supply (BAT) to power window
Battery power supply Power supply to power window and sunroof system
(with power windows)

Revision: October 2008 BCS-6 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
System Input Output
A
• Key switch
Panic alarm IPDM E/R
• Keyfob
• All door switches
• Keyfob B
• Door lock/unlock switch
• IPDM/ER
Vehicle security system • Trunk key cylinder switch (Se-
• Security indicator lamp
dan)
• Front door key cylinder switch
C
LH
• Ignition switch
Battery saver control IPDM E/R D
• Combination switch
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
E
Front fog lamp (with front fog lamps) Combination switch IPDM E/R
• Turn signal lamp
Turn signal lamp Combination switch
• Combination meter
F
• Turn signal lamp
Hazard lamp Hazard switch
• Combination meter
• Key switch
G
• Keyfob
• Main power window and door
Room lamp timer Interior room lamp
lock/unlock switch
• Front door switch LH H
• All door switch
Back door switch signal (Hatchback) Back door lock assembly Luggage room lamp
Back door lock signal (Hatchback) Back door lock assembly Back door opener I
Trunk lamp switch and trunk re-
Trunk lamp switch signal (Sedan) Luggage room lamp
lease solenoid
Trunk lamp switch and trunk re- J
Trunk lid opener signal (Sedan) Trunk lid opener
lease solenoid
• Key switch
Key warning chime Combination meter (warning buzzer)
• Front door switch LH BCS
• Combination switch
Light warning chime • Key switch Combination meter (warning buzzer)
• Front door switch LH L
• Seat belt buckle switch LH
Seat belt warning chime Combination meter (warning buzzer)
• Ignition switch
• Combination switch M
Front wiper and washer system IPDM E/R
• Ignition switch
Rear window defogger Rear window defogger switch IPDM E/R
Rear wiper and washer system • Combination switch
Rear wiper motor N
(Hatchback) • Ignition switch
A/C switch signal Front air control ECM
Blower fan switch signal Front air control ECM O
A/C indicator signal Front air control A/C indicator
Low tire pressure warning system Remote keyless entry receiver Combination meter
P
CAN Communication System Description INFOID:0000000004306834

Refer to LAN-8, "System Description".

Revision: October 2008 BCS-7 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Schematic INFOID:0000000004306835

AAMWA0064GB

Revision: October 2008 BCS-8 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >

BCS

AAMWA0065GB

Revision: October 2008 BCS-9 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
BCM Terminal Arrangement INFOID:0000000004306836

LIIA2443E

Revision: October 2008 BCS-10 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Terminal and Reference Value for BCM INFOID:0000000004306837

Signal Measuring condition

Wire Reference value or waveform B
Terminal Signal name input/ Ignition
color Operation or condition (Approx.)
output switch

Combination switch Lighting, turn, wiper OFF

2 BR Input ON
input 5 Wiper dial position 4 D

SKIA5291E
E

Combination switch Lighting, turn, wiper OFF F

3 GR Input ON
input 4 Wiper dial position 4

G
SKIA5292E

H
Combination switch Lighting, turn, wiper OFF
4 L Input ON
input 3 Wiper dial position 4
I

SKIA5291E

Combination switch J
5 G
input 2

Lighting, turn, wiper OFF

Input ON BCS
Combination switch Wiper dial position 4
6 V
input 1

SKIA5292E L
Front door key cylin- ON (open, 2nd turn) Momentary 1.5V
77 BR
der switch LH (unlock)
Input
OFF (closed) 0V
OFF M
Front door key cylin- On (open) Momentary 1.5V
87 Y
der switch LH (lock)
Input
OFF (closed) 0V
Rear window defogger switch
0V N
Rear window defogger ON
9 W Input ON
switch Rear window defogger switch
5V
OFF
O
Ignition switch (ACC ACC or
11 L Input Ignition switch ACC or ON Battery voltage
or ON) ON
ON (open) 0V
12 SB Front door switch RH Input OFF P
OFF (closed) Battery voltage
ON (open) 0V
13 GR Rear door switch RH Input OFF
OFF (closed) Battery voltage
Tire pressure warning
15 W Input OFF — 5V
check connector

Revision: October 2008 BCS-11 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Signal Measuring condition
Wire Reference value or waveform
Terminal Signal name input/ Ignition
color Operation or condition (Approx.)
output switch
Remote keyless entry
18 V Output OFF — 0V
receiver (ground)

Remote keyless entry

19 BR receiver (power sup- Output OFF Ignition switch OFF
ply)

LIIA1893E

Stand-by (keyfob buttons re-

leased)

Remote keyless entry LIIA1894E

20 G Input OFF
receiver signal (signal)

When remote keyless entry

receiver receives signal from
keyfob (keyfob buttons
pressed)

LIIA1895E

Just after turning ignition switch

Input/ OFF → ON: Pointer of tester should
21 P NATS antenna amp. Ignition switch (OFF → ON)
Output ON move for approx. 1 second, then
return to battery voltage.
Security indicator Goes OFF → illuminates (Ev-
23 R Output OFF Battery voltage → 0V
lamp ery 2.4 seconds)
Just after turning ignition switch
Input/ OFF → ON: Pointer of tester should
25 LG NATS antenna amp. Ignition switch (OFF → ON)
Output ON move for approx. 1 second, then
return to battery voltage.

26 GR Thermo control amp. Input ON A/C switch ON

ZJIA0719J

Compressor ON sig- A/C switch OFF 5V

27 O Input ON
nal A/C switch ON 0V
Front blower motor OFF Battery voltage
28 P Front blower monitor Input ON
Front blower motor ON 0V
ON 0V
29 L Hazard switch Input OFF
OFF 5V

Revision: October 2008 BCS-12 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Signal Measuring condition
Wire Reference value or waveform A
Terminal Signal name input/ Ignition
color Operation or condition (Approx.)
output switch
Back door open (switch
0V B
Back door/trunk out- closed)
301 V
put
Output —
Back door closed (switch
5V
open)
All doors locked (SW OFF) Battery voltage C
Back door opener
303 V
switch
Input —
All doors unlocked (SW ON) 0V

Trunk lid opener All doors locked (SW OFF) Battery voltage
304 V Input — D
switch All doors unlocked (SW ON) 0V

Combination switch Lighting, turn, wiper OFF

32 LG Output ON
output 5 Wiper dial position 4
F

SKIA5291E

Combination switch Lighting, turn, wiper OFF H

33 Y Output ON
output 4 Wiper dial position 4

SKIA5292E I

J
Combination switch Lighting, turn, wiper OFF
34 V Output ON
output 3 Wiper dial position 4
BCS
SKIA5291E

Combination switch
35 R
output 2
L

Lighting, turn, wiper OFF

Output ON
Combination switch Wiper dial position 4 M
36 P
output 1

SKIA5292E
N
Key switch and igni- Intelligent Key inserted Battery voltage
371 G
tion knob switch
Input OFF
Intelligent Key removed 0V

Key switch and key Key inserted Battery voltage O

372 G
lock solenoid
Input OFF
Key removed 0V
38 W Ignition switch (ON) Input ON — Battery voltage
P
39 L CAN-H — — — —
40 P CAN-L — — — —

Trunk key cylinder ON (Full unlock position) 0V

416 W
switch
Input —
OFF (Neutral position) 5V
ON (trunk open) 0V
426 Y Trunk lamp switch Input OFF
OFF (trunk closed) Battery voltage

Revision: October 2008 BCS-13 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Signal Measuring condition
Wire Reference value or waveform
Terminal Signal name input/ Ignition
color Operation or condition (Approx.)
output switch
ON (open) 0V
435 R Back door switch Input OFF
OFF (closed) Battery voltage
Rear wiper operating 0
445 LG Rear wiper auto stop Input ON
Rear wiper stopped Battery
ON (lock) 0V
457 GR Lock switch Input OFF
OFF Battery voltage
ON (unlock) 0V
467 L Unlock switch Input OFF
OFF Battery voltage
ON (open) 0V
47 BR Front door switch LH Input OFF
OFF (closed) Battery voltage
ON (open) 0V
48 O Rear door switch LH Input OFF
OFF (closed) Battery voltage
Any door open (ON) 0V
49 P Luggage room lamp Output OFF
All doors closed (OFF) Battery voltage
A/C OFF 0
50 SB A/C indicator Output ON
A/C ON Battery voltage
Back door lock assem-
535 R
bly (actuator)
Output OFF Back door (open) Battery voltage

Trunk lamp switch and

536 R
trunk release solenoid
Output OFF Trunk lid (open) Battery voltage

Rear wiper motor out- OFF 0

555 V
put
Output ON
ON Battery voltage
30 minutes after ignition
OFF 0V
56 R Battery saver output Output switch is turned OFF
ON — Battery voltage
57 LG Battery power supply Input OFF — Battery voltage

Front door lock actua- OFF (neutral) 0V

597 G
tor LH (unlock)
Output OFF
ON (unlock) Battery voltage

60 V Turn signal (left) Output ON Turn left ON

SKIA3009J

61 W Turn signal (right) Output ON Turn right ON

SKIA3009J

Any door ON (open) 0V

63 BR Interior room lamp Output OFF
switch OFF (closed) Battery voltage

Revision: October 2008 BCS-14 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Signal Measuring condition
Wire Reference value or waveform A
Terminal Signal name input/ Ignition
color Operation or condition (Approx.)
output switch

All door lock actuators OFF (neutral) 0V

657 SB
(lock)
Output OFF B
ON (lock) Battery voltage
Front door lock actua- OFF (neutral) 0V
tor RH, rear door lock
667 G
actuators LH/RH (un-
Output OFF C
ON (unlock) Battery voltage
lock)
67 B Ground Input ON — 0V
D
Ignition switch ON Battery voltage
Within 45 seconds after igni-
Battery voltage
tion switch OFF
E
Power window power More than 45 seconds after ig-
688 L
supply (RAP)
Output — 0V
nition switch OFF
When front door LH or RH is
open or power window timer 0V F
operates

698 P Battery power supply Output OFF — Battery voltage

G
70 Y Battery power supply Input OFF — Battery voltage
1: With Intelligent Key
2: Without Intelligent Key H
3: Hatchback without Intelligent Key
4: Sedan without Intelligent Key
5: Hatchback I
6: Sedan
7: With power door locks
8: With power windows J
BCM Power Supply and Ground Circuit Inspection INFOID:0000000004306838

1.CHECK FUSES AND FUSIBLE LINK BCS

• Check 40A fusible link (letter g , located in the fuse and fusible link box).
• Check 10A fuses [No. 6, 8 and 20, located in the fuse block (J/B)].
L
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3, "Schematic" . M
2.CHECK BCM POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF. N
2. Disconnect BCM.
3. Check voltage between BCM connectors and ground.
O
Terminals Power Voltage (V) (Ap-
Connector Condition
(+) (-) source prox.)

Ignition P
ACC
switch
11 Ground power Battery voltage
ACC or
supply
M18 ON
LIIA2415E
Ignition Ignition
38 Ground power switch ON Battery voltage
supply or START

Revision: October 2008 BCS-15 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Terminals Power Voltage (V) (Ap-
Connector Condition
(+) (-) source prox.)

Battery Ignition
57 Ground power switch Battery voltage
supply OFF
M20
Battery Ignition
70 Ground power switch Battery voltage
supply OFF
OK or NG
OK >> GO TO 3.
NG >> Repair or replace the harness.
3.CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 terminal 67 and
ground.

67 - Ground : Continuity should exist.

OK or NG
OK >> Power supply and ground circuit is OK.
NG >> Repair or replace harness.

LIIA0915E

CONSULT-III Function (BCM) INFOID:0000000004306839

CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.

BCM diagnostic
Diagnostic mode Content
test item
Supports inspections and adjustments. Commands are transmitted to the BCM for
WORK SUPPORT setting the status suitable for required operation, input/output signals are received
from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT
The results of transmit/receive diagnosis of CAN communication can be read.
MNTR
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.

ITEMS OF EACH PART

NOTE:
CONSULT-III will only display systems the vehicle possesses.

Diagnostic test mode (Inspection by part)

CONSULT-III dis- SELF− CAN DIAG ECU AC- CON-
System and item WORK DATA
play DIAG RE- SUPPORT PART TIVE FIGU-
SUPPORT MONITOR
SULTS MNTR NUMBER TEST RATION
BCM BCM × × × × ×
Power door lock sys-
DOOR LOCK × × ×
tem
REAR DEFOG-
Rear defogger × ×
GER
Warning chime BUZZER × ×

Revision: October 2008 BCS-16 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
Diagnostic test mode (Inspection by part)
CONSULT-III dis- A
System and item SELF− CAN DIAG ECU AC- CON-
play WORK DATA
DIAG RE- SUPPORT PART TIVE FIGU-
SUPPORT MONITOR
SULTS MNTR NUMBER TEST RATION
Room lamp timer INT LAMP × × × B
Remote keyless entry MULTI REMOTE
× × ×
system ENT
Headlamp HEAD LAMP × × × C
Wiper WIPER × × ×
Turn signal lamp
FLASHER × × D
Hazard lamp
Blower fan switch sig-
nal AIR CONDITION-
× E
Air conditioner switch ER
signal
INTELLIGENT
Intelligent Key ×
KEY F
Combination switch COMB SW ×
NVIS (NATS) IMMU × ×
G
Interior lamp battery BATTERY SAV-
× × ×
saver ER
Back door/Trunk TRUNK × ×
H
Theft alarm THEFT ALARM × × ×
Retained accessory
RETAINED PWR × × ×
power control
I
Oil pressure switch SIGNAL BUFFER × ×
Low tire pressure moni- AIR PRESSURE
× × × ×
tor MONITOR J
Panic alarm PANIC ALARM ×

WORK SUPPORT
BCS
Display Item List

Item Description L
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.

CAN Communication Inspection Using CONSULT-III (Self-Diagnosis) INFOID:0000000004306840 M

1.SELF-DIAGNOSTIC RESULT CHECK

1. Connect CONSULT–III and select “BCM” on “SELECT SYSTEM” screen. N
2. Select “BCM” on “SELECT TEST ITEM” screen, and select “SELF-DIAG RESULTS”.
3. Check display content in self-diagnostic results.
O
CONSULT-III display code Diagnosis item
INITIAL DIAG
TRANSMIT DIAG P
ECM
U1000
IPDM E/R
METER/M&A
I-KEY
Contents displayed

Revision: October 2008 BCS-17 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
No malfunction>>Inspection End
Malfunction in CAN communication system>>After printing the monitor items, go to “CAN System”. Refer to
LAN-17, "Trouble Diagnosis Flow Chart".
Configuration INFOID:0000000004306841

DESCRIPTION
CONFIGURATION has three functions as follows:
• READ CONFIGURATION is the function to read (extract) vehicle configuration of current BCM.
• WRITE CONFIGURATION-Manual selection is the function to select and write vehicle configuration on BCM
manually.
• WRITE CONFIGURATION-Config file is the function to write vehicle configuration with the data extracted
from current BCM.
• For READ CONFIGURATION and WRITE CONFIGURATION-Config file, refer to CONSULT-III Operation
Manual.
• For WRITE CONFIGURATION-Manual selection using the following flow chart, identify the correct model
and configuration list. Confirm and/or change setting value for each item according to the configuration list.
Depending on CONSULT-III software version being used, some or all of the write configuration items shown
in the following configuration lists may be displayed. If an item does not appear on the CONSULT-III WRITE
CONFIGURATION-Manual selection screen(s), then it is an auto setting item and it cannot be manually set
or changed.
NOTE:
Confirm vehicle model on IDENTIFICATION PLATE. Refer to GI-43, "Model Variation".
Models with VIN up to 386333

ITEM SET VAL NOTE

KEYLESS ENTRY WITH ⇔ WITHOUT —
I-KEY WITH ⇔ WITHOUT —
DTRL WITH ⇔ WITHOUT —
THEFT ALARM WITH ⇔ WITHOUT —

Models with VIN starting with 386334

HR16DE Models

ITEM SET VAL NOTE

SPEED SNS WIP WITH ⇔ WITHOUT —

MR18DE Models

ITEM SET VAL NOTE

KEYLESS ENTRY WITH ⇔ WITHOUT —
I-KEY WITH ⇔ WITHOUT —
SPEED SNS WIP WITH ⇔ WITHOUT —
THEFT ALARM WITH ⇔ WITHOUT —
CAUTION:
• When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
• Complete the procedure of WRITE CONFIGURATION in order.
• If you set incorrect WRITE CONFIGURATION, incidents will occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
Removal and Installation of BCM INFOID:0000000004306842

REMOVAL
CAUTION:
Before replacing BCM, perform "READ CONFIGURATION" to save or print current vehicle specifica-
tion. Refer to BCS-18, "Configuration".
1. Remove the glove box. Refer to IP-12, "Removal and Installation".

Revision: October 2008 BCS-18 2009 Versa

 BCM (BODY CONTROL MODULE)
< SERVICE INFORMATION >
2. Remove the BCM screws, disconnect the connectors and
remove the BCM (1). A

WKIA5672E

D
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When replacing BCM, perform "WRITE CONFIGURATION". Refer to BCS-18, "Configuration". E
• When replacing BCM, perform the system initialization (NATS). Refer to the CONSULT-III operation
manual for the initialization procedure.
• When replacing BCM, if new BCM does not come with keyfobs attached, all existing keyfobs must be F
re-registered. Refer to the CONSULT-III operation manual for the initialization procedure.

BCS

Revision: October 2008 BCS-19 2009 Versa