Scribd
Upload
409 views

Powerflex 750 Series: Stop Mode: Id: Qa32991 - Access Levels: Everyone

Uploaded by

Hitesh Panigrahi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
409 views

Powerflex 750 Series: Stop Mode: Id: Qa32991 - Access Levels: Everyone

Uploaded by

Hitesh Panigrahi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

3/6/2020 PowerFlex 750 Series: Stop Mode

Support Center Get Support  Training & Webinars jrobinson@s… 


Online Forum

 
My TechConnect Knowledgebase Issues
Seeing the title of an article twice - Please refresh your browser (click the refresh button in the URL bar or press
F5).
We apologize for the inconvenience.
 

ID: QA32991 | Access Levels: Everyone

PowerFlex 750 Series: Stop Mode


READ LATER:  Email this page  Print

Ask a question... SEARCH

ADD TO FAVORITES

Document ID QA32991

Published Date 02/14/2020

Summary
PowerFlex 750 Series: Stop Mode

Question
How can the drive be set to coast to stop instead to ramp to a stop in the PowerFlex
750 Series AC Drives?
What are the Stop modes description in the PowerFlex 750 Series AC Drives?
What is the difference between coast to stop and ramp to stop in the PowerFlex 750
Series AC Drives?

https://rockwellautomation.custhelp.com/app/answers/answer_view/a_id/731287/loc/en_US#__highlight 1/3
3/6/2020 PowerFlex 750 Series: Stop Mode

20F PowerFlex 753


20G PowerFlex 755

Answer
Parameter 370 [Stop Mode A] sets the type of stop that the drive will performed. The options are the following.

. "Coast" (0) – Power removed from motor, motor coasts to zero.


. "Ramp" (1) – Decelerates to zero speed at the decel rate. Power is removed when zero
speed is reached.
. "Ramp to Hold" (2) – Decelerates to zero speed at the decel rate, followed by DC
braking until the next start sequence.
. "DC Brake" (3) – DC braking is immediately applied (does not follow programmed
decel ramp). May have to adjust parameter 397 [DC Brake Kp].
. "DCBrkAutoOff" (4) – Applies DC braking until zero speed is reached or DC brake time
is reached, whichever is shorter.
. "Current Lmt" (5) – Max torque / current applied until zero speed.
. "Fast Brake" (6) – High slip braking for maximum braking performance above base
speed.

By default the drive will perform the Stop Mode selected in Parameter 370 [Stop Mode A]. However, the drive
can be configured and commanded to use the stop mode selected in Parameter 371 [Stop Mode B] using digital
inputs or DeviceLogix.

Another way to do coast to stop is using digital input, link Parameter 160 [DI Coast Stop] to a digital input. This
is a normally closed control.

Was this answer helpful?


Yes No

RATE CONTENT

https://rockwellautomation.custhelp.com/app/answers/answer_view/a_id/731287/loc/en_US#__highlight 2/3
3/6/2020 PowerFlex 750 Series: Stop Mode

Recently Viewed

PowerFlex 750 Series PowerFlex 527 and Replacing a


Firmware Supervisor Absolute Encoders PowerFlex 527 Drive

 
DISCLAIMER
This knowledge base web site is intended to provide general technical information on a particular subject or
subjects and is not an exhaustive treatment of such subjects. Accordingly, the information in this web site is not
intended to constitute application, design, software or other professional engineering advice or services. Before
making any decision or taking any action, which might affect your equipment, you should consult a qualified
professional advisor.

ROCKWELL AUTOMATION DOES NOT WARRANT THE COMPLETENESS, TIMELINESS OR ACCURACY OF ANY OF THE
DATA CONTAINED IN THIS WEB SITE AND MAY MAKE CHANGES THERETO AT ANY TIME IN ITS SOLE DISCRETION
WITHOUT NOTICE. FURTHER, ALL INFORMATION CONVEYED HEREBY IS PROVIDED TO USERS "AS IS." IN NO EVENT
SHALL ROCKWELL BE LIABLE FOR ANY DAMAGES OF ANY KIND INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS PROFIT OR DAMAGE, EVEN IF ROCKWELL AUTOMATION HAVE BEEN ADVISED ON THE
POSSIBILITY OF SUCH DAMAGES.

ROCKWELL AUTOMATION DISCLAIMS ALL WARRANTIES WHETHER EXPRESSED OR IMPLIED IN RESPECT OF THE
INFORMATION (INCLUDING SOFTWARE) PROVIDED HEREBY, INCLUDING THE IMPLIED WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE, MERCHANTABILITY, AND NON-INFRINGEMENT. Note that certain jurisdictions do not
countenance the exclusion of implied warranties; thus, this disclaimer may not apply to you.

www.rockwellautomation.com

Copyright © 2020 Rockwell Automation, Inc. All Rights Reserved.


  

https://rockwellautomation.custhelp.com/app/answers/answer_view/a_id/731287/loc/en_US#__highlight 3/3

You might also like