Packet Tracer - Configure a Wireless Network (Instructor Version)

Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only.

13.1.10 Packet Tracer – Configure a Wireless Network Answer

Objectives
 Connect to a wireless router
 Configure the wireless router
 Connect a wired device to the wireless router
 Connect a wireless device to the wireless router
 Add an AP to the network to extend wireless coverage
 Update default router settings

Introduction
In this activity, you will configure a wireless router and an access point to accept wireless clients and route IP
packets. Furthermore, you will also update some of the default settings.

Instructions
Part 1: Connect to a Wireless Router

Step 1: Connect Admin to WR.

a. Connect Admin to WR using a straight-through Ethernet cable through the Ethernet ports. Select
Connections, represented by a lightning bolt, from the bottom-left side of Packet Tracer. Click Copper
Straight-Through, represented by a solid black line.
b. When the cursor changes to connection mode, click Admin and choose FastEthernet0. Click WR and
choose an available Ethernet port to connect the other end of the cable.
WR will act as a switch to the devices connected to the LAN and as a router to the internet. Admin is now
connected to the LAN (GigabitEthernet 1). When Packet Tracer displays green triangles on both sides of
the connection between Admin and WR, continue to the next step.
Note: If no green triangles are shown, make sure to enable Show Link Lights under Options >
Preferences. You may also click Fast Forward Time just above the Connections selection box in the
yellow bar.

Step 2: Configure Admin to use DHCP.

To reach the WR management page, Admin must communicate on the network. A wireless router usually
includes a DHCP server, and the DHCP server is usually enabled by default on the LAN. Admin will receive
IP address information from the DHCP server on WR.
a. Click Admin, and select the Desktop tab.
b. Click IP Configuration and select DHCP.

 2015 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 5 www.netacad.com
Packet Tracer - Configure a Wireless Network

Questions:

What is the IP address of the computer?

Type your answers here.
192.168.0.100
What is the subnet mask of the computer?
Type your answers here.
255.255.255.0
What is the default gateway of the computer?
Type your answers here.
192.168.0.1
c. Close the IP Configuration window.
Note: Values can vary within the network range due to normal DHCP operation.

Step 3: Connect to the WR Web Interface.

a. In the Desktop tab on Admin, choose Web Browser.
b. Enter 192.168.0.1 in the URL field to open the web configuration page of the wireless router.
c. Use admin for both the username and password.
d. Under the Network Setup heading on the Basic Setup page, notice the IP address range for the DHCP
server.
Question:

Is the IP address for Admin within this range? Is it expected? Explain your answer.
Type your answers here.

Yes. Admin has 192.168.0.100/24 which belongs to 192.168.0.0/24 and in the range of
192.168.0.100 to 192.168.0.149. It is expected because Admin acquired its IP information from WR
via DHCP.

Step 4: Configure the Internet Port of WR.

In this step, WR is configured to route the packets from the wireless clients to internet. You will configure the
Internet port on WR to connect to the internet.
a. Under the Internet Setup at the top of the Basic Setup page, change the Internet IP address method
from Automatic Configuration – DHCP to Static IP.
b. Type the IP address to be assigned to the Internet interface as follows:
Internet IP Address: 209.165.200.225
Subnet Mask: 255.255.255.252
Default Gateway: 209.165.200.226
DNS Server: 209.165.201.1
c. Scroll down the page and click Save Settings.
Note: If you get a Request Timeout message, close the Admin window and wait for the orange lights to
turn into green triangles. Click the fast forward button to make this happen faster. Then reconnect to WR
from Admin’s browser using the process explained in Step 3.
d. To verify connectivity, open a new web browser and navigate to www.cisco.pka server.

 2015 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 5 www.netacad.com
Packet Tracer - Configure a Wireless Network

Note It may take a few seconds for the network to converge. Click Fast Forward Time or Alt+D to speed
up the process.

Part 2: Configure the Wireless Settings

In this activity, you will only configure the wireless settings for 2.4 GHz.

Step 1: Configure the WR SSID.

a. Navigate to the WR GUI interface at 192.168.0.1 in a web browser on Admin.
b. Navigate to Wireless > Basic Wireless Settings.
c. Change Network Name (SSID) to aCompany for only 2.4 GHz. Notice that SSIDs are case-sensitive.
d. Change the Standard Channel to 6 - 2.437GHz.
e. For this activity, disable both 5 GHz frequencies. Leave the rest of the settings unchanged.
f. Scroll to the bottom of the window and click Save Settings.

Step 2: Configure wireless security settings.

In this step, you configure the wireless security settings using WPA2 security mode with encryption and
passphrase.
a. Navigate to Wireless > Wireless Security.
b. Under the 2.4 GHz heading, select WPA2 Personal for the Security Mode.
c. For the Encryption field, keep the default AES setting.
d. In the Passphrase field, enter Cisco123! as the passphrase.
e. Click Save Settings.
f. Verify that the settings in the Basic Wireless Settings and Wireless Security pages are correct and
saved.

Step 3: Connect the Wireless Clients.

a. Open Laptop1. Select Desktop tab. Click PC Wireless.
b. Select the Connect tab. Click Refresh as necessary. Select the Wireless Network Name aCompany.
c. Enter the passphrase configured in the previous step. Enter Cisco123! In the pre-shared key field and
click Connect. Close the PC Wireless window.
d. Open a web browser and verify that you can navigate to www.cisco.pka server.
e. Repeat the above steps to connect Laptop2 to the wireless network.

Part 3: Connect Wireless Clients to an Access Point

An access point (AP) is a device that extends the wireless local area network. An access point is connected
to a wired router using an Ethernet cable to project the signal to a desired location.

Step 1: Configure the Access Point.

a. Connect Port 0 of AP to an available Ethernet port of WR using a straight-through Ethernet cable.
b. Click AP. Select the Config tab.
c. Under the INTERFACE heading, select Port 1.
d. In the SSID field, enter aCompany.

 2015 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 5 www.netacad.com
Packet Tracer - Configure a Wireless Network

e. Select WPA2-PSK. Enter the passphrase Cisco123! In the Pass Phrase field.
f. Keep AES as the default Encryption Type.

Step 2: Connect the Wireless Clients.

a. Open Laptop3. Select Desktop tab. Click PC Wireless.
b. Select the Connect tab. Click Refresh as necessary. Select the Wireless Network Name aCompany with
the stronger signal (Channel 1) and click Connect.
c. Open a web browser and verify that you can navigate to www.cisco.pka server.

Part 4: Other Administrative Tasks

Step 1: Change the WR Access Password.

a. On Admin, navigate to WR GUI interface at 192.168.0.1.
b. Navigate to Administration > Management and change the current Router Password to cisco.
c. Scroll to the bottom of the window and click Save Settings.
d. Use the username admin and the new password cisco when prompted to log in to the wireless router.
Click OK to continue.
e. Click Continue and move on to the next step.

Step 2: Change the DHCP address range in WR.

In this step, you will change the internal network address from 192.168.0.0/24 to 192.168.50.0/24. When the
LAN network address changes, the IP addresses on the devices in the LAN and WLAN must be renewed to
receive new IP addresses before the lease is timed out.
a. Navigate to Setup > Basic Setup.
b. Scroll down the page to Network Setup.
c. The IP address assigned to Router IP is 192.168.0.1. Change it to 192.168.50.1. Verify that IP address
still start at .100, and there are 50 available IP addresses in the DHCP pool.
d. Add 209.165.201.1 as the DNS server with the DHCP settings.
e. Scroll to the bottom of the window and click Save Settings.
f. Note that the DHCP range of addresses has been automatically updated to reflect the interface IP
address change. The Web Browser will display a Request Timeout after a short time.
Question:

Why?
Type your answers here.

Because the Admin IP address is no longer within the same network as the router. The IP address
of Admin is outside the new range of the DHCP server.
g. Close the Admin web browser.
h. In Admin Desktop tab, click Command Prompt.
i. Type ipconfig /renew to force Admin re-acquire its IP information via DHCP.
Question:

What is the new IP address information for Admin?

Type your answers here.

 2015 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 5 www.netacad.com
Packet Tracer - Configure a Wireless Network

Your answer may vary. The IP address for Admin is within 192.168.50.100 - 149.
IP Address: ........................................... 192.168.50.100
Subnet Mask: ....................................... 255.255.255.0
Default Gateway: .................................. 192.168.50.1
DNS Server: .......................................... 209.165.201.1
j. Verify that you can still navigate to www.cisco.pka server.
k. Renew the IP address on other laptops to verify that you can still navigate to www.cisco.pka server.
l. Notice that Laptop1 connected to the AP instead of WR.
Question:

Why?
Type your answers here.
The AP had a better signal for Laptop1.
End of Document

 2015 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 5 www.netacad.com