Scribd
Upload
267 views4 pages

The WEB Interface Setting of EBIT E9 Miner

The document provides steps for setting up the WEB interface of an EBIT E9 miner, including: 1) Setting the router LAN port and computer wired network card IP to match the miner's default IP of 192.168.80.140. 2) Logging into the miner interface with the default username and password of "admin". 3) Configuring the miner settings, including selecting a mining pool and entering login credentials.

Uploaded by

Mehdi Mansourian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
267 views4 pages

The WEB Interface Setting of EBIT E9 Miner

The document provides steps for setting up the WEB interface of an EBIT E9 miner, including: 1) Setting the router LAN port and computer wired network card IP to match the miner's default IP of 192.168.80.140. 2) Logging into the miner interface with the default username and password of "admin". 3) Configuring the miner settings, including selecting a mining pool and entering login credentials.

Uploaded by

Mehdi Mansourian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

The WEB interface setting of EBIT E9 miner is simple and friendly.

You can easily set up the miner by


following thesteps below. The factory IP of EBIT is usually 192.168.80.140. If your machine is faulty, don't
worry, wewill provide you with a 6-month warranty for whole machine, 12-month warranty for control
boards.Please be patient and read the following steps
1)The latest batch of EBIT miner default address is 192.168.80.140. The hardware connection can not be
opened normally. The miner and the computer IP are not in the same network segment and need to be set.

1:Open your router configuration, set the router's LAN port to 192.168.80.1, the general router defaults to
192.168.1.1 or 192.168.0.1, if it is 192.168.80.1, there is no need to modify it. After the modification, restart
the router and connect the wing bits to the router with the network cable.

2:Set the ip of your computer's wired network card to 192.168.80.199, subnet mask 255.255.255.0, and
leave the gateway blank. First point the network neighbor to find the local connection, select the Internet
protocol point properties, open the window settings, click OK and then OK, and finally right click on the local
connection point to repair, ensure that the settings take effect in real time.
2）After the route restart is complete, open your browser and enter the IP address on your mining fan. The
default is 192.168.80.140, then press Enter. Enter the default user account of the miner admin, the password is
also admin by default, then click login to log in.

3）After logging in to the mining machine, click on the device information ----- device status, you
can see the device frequency, computing power, temperature, and the system configuration is displayed
on the page (intuitive reaction pool task no response times, power warning, temperature Warning
threshold, device shutdown temperature threshold, frequency setting, etc.).

4）Click the network management button to enter the network management information configuration page.
If there are more than two wing bits, please modify the IP address to other addresses. Be sure to
click the Settings button after making changes.
5）Click the miner and click on the miner settings to enter the miner configuration page. Mine Pool 1 information
is configured with f2pool, stratum+tcp://stratum.f2pool.com:3333 is the mine pool, some networks will block
3333 ports, f2pool can be replaced with 8888 or 25, wsxeric is my miner name, password is The password (the
name of the miner should correspond to the name of the miner in the mine pool, and the password can be filled
in as needed). The mining pool is divided into three groups, which can be filled in three groups. If the first
group of mines is hung, it will automatically switch to the second group. Similarly, the second group of mines
will automatically switch to the third group. After the configuration is completed, mining can be carried out.
Click on the setting to make the mining pool effective. Enter the miner state to observe whether the mining
machine is working normally.

6）Click System. Go to the System Status page, where you can get the device board temperature,
system hardware, software version number, and more.
7）Click Maintenance Management to enter the upgrade interface. The official website will update the device
firmware from time to time. At that time, the mine friends can extract and download the upgrade device to
improve the performance of the device. Note: Failure of the firmware upgrade will cause permanent damage to
the system. Please perform firmware upgrade by the manufacturer or under the guidance of the manufacturer.
The upgrade file path cannot contain Chinese. Entering the restart interface, the system restart will restart all
units.

You might also like