Concrete pumping

Code of Practice 2005

This Queensland code of practice was preserved as a code of practice under section 284 of the
Work Health and Safety Act 2011.

This code was varied by the Minister for Education and Industrial Relations on 27 November 2011 and
published in the Queensland Government Gazette on 2 December 2011.

This preserved code commences on 1 January 2012.

PN11172

© The State of Queensland (Department of Justice and Attorney-General) 2011

Copyright protects this document. The State of Queensland has no objection to this material being reproduced, but asserts its right to be
recognised as author of the original material and the right to have the material unaltered.
The material presented in this publication is distributed by the Queensland Government as an information source only. The State of
Queensland makes no statements, representations, or warranties about the accuracy or completeness of the information contained in this
publication, and the reader should not rely on it. The Queensland Government disclaims all responsibility and all liability (including,
without limitation, liability in negligence) for all expenses, losses, damages and costs you might incur as a result of the information being
inaccurate or incomplete in any way, and for any reason.

PN11172 Concrete Pumping Code of Practice 2005 Page 2 of 27

Contents
Introduction ......................................................................................................................... 4
1. Managing the risks from concrete pumping................................................................. 5
2. Risks associated with concrete pumping plant ........................................................... 5
3. Planning and preparation ............................................................................................... 6
3.1 Planning by the principal contractor or person in control of the workplace............................................... 6
3.2 Planning by the concrete pumper ............................................................................................................. 7
4. Risk controls for concrete pumping plant .................................................................... 8
4.1 Plant and equipment ................................................................................................................................. 8
4.1.1 Concrete placement booms............................................................................................................... 8
4.1.2 Pump gauges..................................................................................................................................... 9
4.1.3 Concrete pipelines and restraint equipment ...................................................................................... 9
4.1.4 Hose whip ........................................................................................................................................ 11
4.2 Placement of plant and equipment.......................................................................................................... 13
4.2.1 Setting-up on site ............................................................................................................................. 13
4.2.2 Setting-up near powerlines or electrical equipment......................................................................... 14
4.2.3 Setting-up in a public place.............................................................................................................. 15
4.2.4 Traffic control ................................................................................................................................... 15
4.3 Tasks ....................................................................................................................................................... 16
4.3.1 Concrete delivery ............................................................................................................................. 16
4.3.2 Pump and boom operation .............................................................................................................. 17
4.3.3 Concrete pouring ............................................................................................................................. 18
4.3.4 Line cleaning (on site)...................................................................................................................... 18
4.3.5 Pump cleaning (on site) ................................................................................................................... 19
4.3.6 Preparation for road travel ............................................................................................................... 20
4.4 By-products ............................................................................................................................................. 20
4.4.1 Noise ................................................................................................................................................ 20
4.4.2. Fumes ............................................................................................................................................. 20
5. Inspection and maintenance ........................................................................................ 21
5.1 General.................................................................................................................................................... 21
5.2 Compliance plates and certification ........................................................................................................ 21
5.3 Pre-operational inspections..................................................................................................................... 22
5.4 Routine maintenance inspections ........................................................................................................... 22
5.5 Annual inspections .................................................................................................................................. 22
5.6 Assessment for service and continued use............................................................................................. 22
5.7 Inspection report...................................................................................................................................... 23
5.8 Welding and other repairs ....................................................................................................................... 23
5.9 Reporting defects .................................................................................................................................... 23
5.10 Log books and inspection record sheets............................................................................................... 23
5.11 Warning and safety signs...................................................................................................................... 23
5.12 Pipe testing, identification and marking................................................................................................. 24
6. Safety equipment .......................................................................................................... 24
6.1 Provision of personal protective equipment (PPE) ................................................................................. 24
6.2 Additional equipment............................................................................................................................... 24
7. Training and supervision.............................................................................................. 24
Appendix 1: Dictionary ..................................................................................................... 26

PN11172 Concrete Pumping Code of Practice 2005 Page 3 of 27

Introduction
This Concrete Pumping Code of Practice 2005 is an approved code of practice under section 274 of
the Work Health and Safety Act 2011 (the Act).

An approved code of practice is a practical guide to achieving the standards of health, safety and
welfare required under the Act and the Work Health and Safety Regulation 2011 (the Regulation).

A code of practice applies to anyone who has a duty of care in the circumstances described in the
code. In most cases, following an approved code of practice would achieve compliance with the
health and safety duties in the Act, in relation to the subject matter of the code. Like regulations,
codes of practice deal with particular issues and do not cover all hazards or risks which may arise.
The health and safety duties require duty holders to consider all risks associated with work, not only
those for which regulations and codes of practice exist.

Codes of practice are admissible in court proceedings under the Act and Regulation. Courts may
regard a code of practice as evidence of what is known about a hazard, risk or control and may rely
on the code in determining what is reasonably practicable in the circumstances to which the code
relates.

Compliance with the Act and Regulation may be achieved by following another method, such as a
technical or an industry standard, if it provides an equivalent or higher standard of work health and
safety than the code.

An inspector may refer to an approved code of practice when issuing an improvement or prohibition
notice.

How is the code organised

In providing guidance, the word ‘should’ is used in this Code to indicate a recommended course of
action, while ‘may’ is used to indicate an optional course of action.

This Code also includes various references to provisions of the Act and Regulation which set out the
legal requirements. These references are not exhaustive. The words ‘must’, ‘requires’ or ‘mandatory’
indicate that a legal requirement exists and must be complied with.

Who has duties?

A person conducting a business or undertaking has the primary duty under the Act to ensure, as
far as reasonably practicable, that workers and other persons are not exposed to health and safety
risks arising from the business or undertaking.

Officers, such as company directors, have a duty to exercise due diligence to ensure that the business
or undertaking complies with the Act and Regulation. This includes taking reasonable steps to ensure
that the business or undertaking has and uses appropriate resources and processes to provide and
maintain a safe work environment.

Workers have a duty to take reasonable care for their own health and safety and that they do not
adversely affect the health and safety of other persons. Workers must comply with any reasonable

PN11172 Concrete Pumping Code of Practice 2005 Page 4 of 27

instruction and cooperate with any reasonable policy or procedure relating to health and safety at the
workplace.

Consulting workers
Consultation involves sharing of information, giving workers a reasonable opportunity to express
views and taking those views into account before making decisions on health and safety matters.

The Act requires that you consult, so far as is reasonably practicable, with workers who carry out
work for you who are (or are likely to be) directly affected by a work health and safety matter.

If the workers are represented by a health and safety representative, the consultation must involve
that representative.

You must consult your workers when proposing any changes to the work that may affect their health
and safety.

Consulting, cooperating and coordinating activities with other duty holders

The Act requires that you consult, cooperate and coordinate activities with all other persons who
have a work health or safety duty in relation to the same matter, so far as is reasonably practicable.

Sometimes you may share responsibility for a health and safety matter with other business operators
who are involved in the same activities or who share the same workplace. In these situations, you
should exchange information to find out who is doing what and work together in a cooperative and
coordinated way so that all risks are eliminated or minimised as far as reasonably practicable.

Further guidance on consultation is available in the Code of Practice: Work Health and Safety
Consultation, Coordination and Cooperation.

1. Managing the risks from concrete pumping

Under the Act, the risks from concrete pumping, like any other risks, must be controlled using a risk
management approach. The object of risk management is to enable you to assess systematically all
the factors about an activity involving concrete pumping plant. This approach will help you make a
judgement about the associated risks and to put in place appropriate control measures. The risk
management approach involves:
(a) identifying concrete pumping plant hazards that pose a risk
(b) assessing the degree of risk created by the plant, environment and work processes
(c) determining and implementing appropriate control measures; and
(d) monitoring and reviewing the effectiveness of the chosen control measures.

It is recommended that the How to Manage Work Health and Safety Risks Code of Practice be
consulted for further information about the risk management process.

2. Risks associated with concrete pumping plant

The risks associated with concrete pumping are many and varied. It may be useful to list risks in
terms of their originating hazard. Risk may originate from hazards such as:
 plant and equipment, e.g.

PN11172 Concrete Pumping Code of Practice 2005 Page 5 of 27

 - concrete placement booms
- pump gauges
- concrete pipelines
- pipe clamps
- anchor brackets
- pipe movement
- delivery hose
- receiving hopper
 placement of plant and equipment, e.g.
- proximity to:
 traffic
 members of the public
 powerlines
 trenches
- ground stability
 tasks, e.g.
- concrete delivery
- pump and boom operation
- concrete pouring
- line cleaning
- pump cleaning
- road travel
 by-products, e.g.
- fumes
- noise.

This document discusses all of the risks listed above, including appropriate control measures.

3. Planning and preparation

Planning and preparation is the first step in ensuring that work is done safely and in order to be
successful must involve consultation with all those engaged in the work.

3.1 Planning by the principal contractor or person in control

of the workplace
When planning for the pumping of concrete the principal contractor or person in control of the
workplace should consult with the concrete pumper regarding risks. The principal contractor or
person in control of the workplace should ensure:
(a) the concrete pump is located in the most favourable position to pump concrete, including
allowing adequate visual contact for the pump operator with both the pump and the pour area. If
this can not be achieved then alternative controls should be implemented (see section 4.3.2)
(b) a clear, level area of ground with a firm base that is capable of supporting the pump unit and the
concrete delivery trucks, is available
(c) clear access to the pump unit for concrete trucks
(d) safe and unobstructed access for the general public, to public areas in the vicinity of the pumping
unit and the delivery trucks, if the pump unit is set up in the street

PN11172 Concrete Pumping Code of Practice 2005 Page 6 of 27

(e) a time schedule is set prior to a major pour commencing, based on a realistic assessment of the
time to complete
(f) an allowance is included for such things as weather, accessibility, volume of concrete, slab &
site limitations, equipment back up, restricted work times (local council rules), equipment
capacity, concrete pumper’s capacity, hose-hand’s limitations and the concrete supplier’s
requirements
(g) that there is a clearly defined ‘pump washout area’ complying with environmental protection
legislation and local authority requirements
(h) where compressed air and water lines are supplied on site, that they are positioned to avoid any
damage and to comply with the appropriate Australian Standards, and
(i) there is a method to collect concrete residue and/or all necessary precautions necessary to
prevent wash down residue from the clean-up of pumping operations finding its way into
stormwater drains (including concrete delivery trucks), particularly where a permanent or semi-
permanent set-up has been established on site or where a pump is set-up in a roadway or public
place, and ensuring that this residue collection method complies with all Environment Protection
Authority requirements.

3.2 Planning by the concrete pumper

The concrete pumper should consult with the principal contractor or person in control of the
workplace in regards to the overall planning for pumping concrete on site. Following this
consultation the concrete pumper should consider:
(a) whether enough workers are available to safely pump concrete, including having a competent
worker present at the pump at all times, to operate the emergency shut down system, in case of
line failure or other events that require the pump to be shutoff – unless the concrete pump is
provided with an automatic system that effectively and reliably shuts down the pump when there
is a likelihood of air entering the system.
(b) the most suitable method of pumping concrete to the pour area
(c) the capacity and type of pump to be used to complete the job satisfactorily within the required
time span
(d) the location of the pump and access for concrete delivery trucks
(e) an assessment of any manual tasks that may cause any muscle or ligament strains, or other
injures
(f) the provision of personal protective equipment and other safety equipment
(g) the provision of safe access including elimination of trip, slip and fall hazards
(h) electrical safety, including the location of nearby powerlines and systems of work which comply
with electrical safety legislation and the recommendations of any local, relevant compliance
requirements
(i) appropriate instruction manuals accompany the pump unit and/or boom, giving sufficient
instructions for operation, maintenance and repairs
(j) the pump operator is trained and competent with the use of the appropriate manuals and the
equipment
(k) maintenance and repair manuals are kept in a safe place at the registered premises, including a
parts catalogue, and are kept up to date with any additional information from the manufacturer,
and
(l) maintenance log books are to be kept on the pump, maintained and be up to date, and are to be
made available on request at the workplace.

PN11172 Concrete Pumping Code of Practice 2005 Page 7 of 27

The concrete pumper should also consult with the concrete delivery company and truck driver prior
to the commencement of pumping. Issues to be discussed:
(a) With the delivery company include:
i. control measures chosen and implemented for line blow-out procedures, based on a risk
assessment
ii. procedures for multiple trucks reversing to the concrete pump.
(b) With the truck driver include:
i. a safe location for the concrete delivery truck driver to stand, when concrete pumping is
occurring
ii. the need to follow any directions of any allocated traffic controllers/spotters
iii. procedures for multiple trucks reversing to the concrete pump.

NOTE: Drivers of pre-mix concrete delivery trucks should not be considered workers for pumping
operations, unless trained to carry out this function and authorised to act in this capacity by their
PCBU.

4. Risk controls for concrete pumping plant

4.1 Plant and equipment
Risk
The interruption of concrete flow and/or failure of pumping equipment can create potentially
dangerous situations. Pressurised concrete escaping from the enclosed pumping system has the
potential to strike workers and others, causing injury. Dislodged, unrestrained or burst pipelines and
associated equipment also pose a risk to concrete pumping workers, delivery truck drivers and other
workers working in and around the designated concrete pumping area. Risks associated with this
plant should be identified in terms of pipe construction and pipe restraint.

The risk of mechanical or structural failure of equipment such as concrete placement booms should
be identified. Concrete placement booms can have a greater risk of failure due to the cyclic loading
of the pulsating pump. The likelihood of fatigue failure of welds is increased in comparison to other
plant that does not have this pulsating load. Restraining devices such as pins and circlips also have an
increased chance of becoming dislodged. These risks apply to both truck mounted and satellite type
booms (building mounted booms).

The information supplied below deals with components of the concrete pumping system. Specific
risk controls are recommended for each of these components. The assessment of risk for these
hazards remains essentially the same in identifying components and assessing the likelihood of
movement or failure.

4.1.1 Concrete placement booms

Risk
Structural or mechanical failure of the concrete placing boom

Risk control
To prevent the structural or mechanical failure of concrete placing booms, regular maintenance in
accordance with the manufacturer’s instructions should be performed. Australian Standard 2550.15

PN11172 Concrete Pumping Code of Practice 2005 Page 8 of 27

Cranes – Safe Use – Concrete placing equipment also provides guidance on the inspection of
concrete placing booms.

When inspecting concrete placing booms, consider:

(a) all functions and their controls for speed(s), smoothness of operation and limits of motion
(b) all emergency and safety devices
(c) lubrication of all moving parts, inspection of filter element(s), hydraulic oil, and coolant as
specified by the manufacturer, and
(d) visual inspection of structural components and other critical components such as fasteners, pins,
shafts, welds and locking devices.

The erection and dismantling of concrete placement booms should be conducted in accordance with
the manufacturer’s instructions unless otherwise specified by a professional engineer.
4.1.2 Pump gauges
Risk
Gauge damage or malfunction.

Risk control
Gauges fitted to the concrete pump should be accurate and of a size and style that are easy to read.
All instruments should be visually checked and tested on a regular basis and replacements (as
recommended by the equipment manufacturer), recorded in the pump’s log book.

4.1.3 Concrete pipelines and restraint equipment

Pipelines
Risk
Concrete pipeline failure.

Risk control
When laying a pipeline, ensure that:
(a) unnecessary bends are avoided
(b) horizontal pipelines are adequately supported
(c) flexible hoses are not at risk of being run over by other plant and equipment being operated in
the area
(d) each section of pipe in a vertical pipeline is supported to avoid extra load on the pipe clamp, in
accordance with AS 2550.15
(e) the 90o bend at the base altering the direction of the concrete line from horizontal to vertical is
equipped with a leg sitting firmly on the ground sufficient to stop any movement in the vertical
line which may snap off the first clamp
(f) vertical lines are positively secured to the building
(g) cranes or hoist towers, scaffolding or formwork are not to be used to secure the line, as this
method may not be capable of taking the impact load when pumping concrete through the line,
and
(h) all metal pipes and pipeline components are identified and checked in accordance with AS
2550.15.

PN11172 Concrete Pumping Code of Practice 2005 Page 9 of 27

Pipe clamps
Risk
Concrete pipe clamp failure.
Risk control
When using quick release pipe clamps on fixed lines (horizontal or vertical), ensure that:
(a) the pipe clamps used are able to sustain the maximum concrete pressure applied to the pipeline
by the pump
(b) the locking pins are used and are engaged
(c) all pipe clamps are regularly inspected by a competent person for signs of wear and fatigue
(d) pipe clamps which show any deformation or damage are immediately replaced
(e) pipe clamps that are manufactured with no provision for locking pins are not used, and
(f) clamps are locked as per the manufacturer’s instructions and are not locked by hammering the
quick release clamp lever, or by other methods which may cause fatigue of the clamp’s metal.

Figure 1. High pressure pipe clamp.

Anchor brackets
Risk
Concrete pipeline failure.
Risk control
When inserting anchor brackets on the concrete delivery pipe the concrete pumper should ensure
that:

(a) anchor brackets and tie-downs are used to adequately secure the system, at intervals of no more
than three metres apart 1 , unless otherwise specified by a competent person
(b) the number of bolts used to secure an anchor bracket should be in accordance with AS 2550 Set,
the pump manufacturer’s specifications or in accordance with advice from a professional
engineer
(c) where friction type ‘drill-in’ anchors are used, these are of the high-load slip, torque controlled
type and have a factor of safety of 3 to 1 based on their failure load

1
It is acknowledged that it may not be practicable in all situations to install anchor brackets every 3
metres. If not practicable a risk assessment should be conducted to ensure that risk of pipe movement
is adequately controlled.

PN11172 Concrete Pumping Code of Practice 2005 Page 10 of 27

(d) chemical anchors are pull out load tested to 125% of their working load and have a factor of
safety of 3 to 1 based on their failure load, and
(e) when securing pipes overhead (i.e. so that the bracket anchors are loaded in pure tension),
‘through bolts’ that extend through the concrete slab are preferable to drill-in type anchors. If
drill-in type anchors are used in this application they should all be pull out load tested to 125%
of their working load.

Figure 2. One method of anchoring pipe.

Pipe movement
Risk
Excessive pipeline movement.
Risk control
Where excessive pipe movement occurs in temporary laid lines due to the surging action of the
pump, to:
(a) use extra anchorage methods to restrict the line movement, especially at bends and elbows, or
(b) install a short wire-braided high pressure rubber hose between the concrete pump and pipelines
in accordance the manufacturer’s recommendations.

4.1.4 Hose whip

Risk
“Hose whip” is the term used to describe uncontrolled and rapid motion of the flexible rubber hose
on the end of a concrete placement boom or other concrete delivery line. Persons can be injured by
being struck directly by the whipping hose itself, or being knocked over and hitting the ground or an
object, or being hit by ejected material.

Hose whip can occur during the concrete pumping operation itself or when the line is being cleaned
out. In either case, hose whip can be especially violent when air enters the line and becomes
pressurised due to an obstruction further down the line, and the obstruction becomes dislodged.

Risk control
The likelihood of hose whip can be greatly reduced by the selection of suitable plant and safe
systems of work. While the risk of hose whip can be reduced, additional precautions need to be taken
to reduce the likelihood of injury.

PN11172 Concrete Pumping Code of Practice 2005 Page 11 of 27

To minimise the likelihood of injury from hose whip:
(a) Only pump concrete that is a pumpable mix as
specified by the concrete supplier. Other types of
Safe
concrete can block the line and cause hose whip.
(b) Do not let the concrete solidify in the line as this will
cause blockages. The concrete needs to remain in its
plastic state.
(c) Use well trained, competent operators to pump
concrete (See Figure 3).
(d) Start the pump up slowly to reduce the likelihood of
hose whip.
(e) Never use a rubber delivery hose with metal fittings
attached to the free end.
(f) Persons not involved in the concrete pour should be
excluded from the delivery hose area.
(g) Never stretch the delivery hose if it doesn’t reach the
pouring location (see Figure 4).
(h) The delivery hose on a boom pump should hang close Figure 3 – Line hand guiding hose and
to vertical and only be guided by the line hand. If the signalling to pump operator.
boom is not long enough to reach the concrete pour
area, a longer boom should be used or the concrete pump should be moved closer to the job.
(i) Workers should always wear appropriate personal protective equipment, including hard hats.
(j) Good housekeeping needs to be maintained around the work area to reduce the likelihood of
tripping.

Unsafe
(k) Do not let more hose hang from the boom than
that allowed by the placement boom
manufacturer. Normally only a maximum of
three or four metres of 125 mm diameter hose
can be suspended from the boom.
(l) Do not allow concrete to drop out of the hose
when pumping is stopped, as this can allow air
to enter the system. The hose can be folded
over to prevent concrete dropping out.
(m) Always ensure the line hand has an adequate
sized area to stand on (the width of the working
Figure 4 – Workers stretching hose for additional surface should be 450 mm or greater). The line
reach. This is an unsafe work practice hand should not stand on block walls or next to
unprotected edges. (See Figure 5.)

PN11172 Concrete Pumping Code of Practice 2005 Page 12 of 27

(n) Monitor the level of concrete in the hopper to
avoid air getting sucked into the pump system.
Ensure a separate person to the line hand is in
position to view the hopper (normally the
Safe
pump operator), unless there is a reliable
automatic shut off device fitted.
(o) Make sure safe work procedures are adopted
for clearing blockages.
(p) Preferably clean out the concrete line with
water instead of air.
(q) When there is no other option but to clean the
pump line out with air, secure the end of the
Figure 5 – Pouring concrete into column form.
steel line and have an exclusion zone. All
Good access provided
reducers and rubber hose must be removed
from the end of the delivery line. A ball catcher
should be fitted to the end of the steel pipe
which will contain the blow out plug (i.e.
sponge) as it is ejected from the line.

4.2 Placement of plant and equipment

4.2.1 Setting-up on site
Risk
There are numerous risks associated with the setting-up of concrete placing equipment, including
concrete pumping booms tipping over and the risk of workers being crushed or run over by the
mobile pump or concrete truck. Consultation regarding the risks involved with the set-up of concrete
placing equipment should occur between the principal contractor or person in control of the
workplace and the concrete pumper.

Risk control
When setting-up a concrete pump the area should be level, capable of supporting the load and free of
obstructions, with careful attention paid to the following.
(a) Particular care and precautions should be taken when a concrete pump is used in the vicinity of
an excavation, as the weight of the concrete pump and the load can affect the stability of the
excavation wall and cause the excavation wall to collapse, which may lead to the concrete pump
overturning. The pump should not be positioned over or adjacent to:
i. previously disturbed ground that has been back-filled,
ii. excavations, trenches or holes in the ground,
iii. cellars, basements or pits, or
iv. inadequately compacted or soft ground.
(b) If the ground is not firm or is near an excavation, the operator should immediately refer the
matter to the principal contractor for re-location to a more stable location.
(c) That the pump unit is set up level, and if this cannot be achieved ensure that the incline or angle
of the machine does not exceed the manufacturers recommendations (refer to operating
instruction manual).
(d) If outriggers are required:
i. supply adequate sole plates for the purpose of packing the base plate,

PN11172 Concrete Pumping Code of Practice 2005 Page 13 of 27

 ii. ensure the outriggers pads are clear of excavations, soft or filled ground, or other obstacles
liable to interfere with the safe operation of the machine,
iii. ensure that the sole plate material, if timber is ‘pigstyed’ and are of sufficient bearing area to
support the machine, and
iv. ensure the outriggers do not subside, by making regular checks to ensure stability.
(e) Unauthorised persons should be kept away from the machine and associated equipment.
(f) Persons working in the concrete pumping exclusion zone should wear high visibility vests.
(g) The exclusion zone should be marked with signage requiring persons to wear high visibility
vests.
(h) The area should be clearly marked and made safe from other traffic.
(i) Set-up areas should be provided with clear access and adequate lighting at all times, during
operation.
(j) Where operation of the plant is required at night or low light conditions, artificial lighting should
be provided.
(k) A sign is posted clearly stating that the area is for authorised persons either, for example ‘Danger
– Concrete Pumping Area – Authorised Persons only’.

4.2.2 Setting-up near powerlines or electrical equipment

Risk
Contact with overhead power lines can pose a major risk when pumping concrete. Before setting-up
concrete pumping equipment in the vicinity of overhead powerlines, consultation regarding risk
should occur between the principal contractor or person in control of the workplace and concrete
pumper. Where it is claimed that power lines have been de-energised, written documentation from
the relevant power supply organisation should be available on site.

The Electrical Safety Regulation 2002 regulates work around overhead power lines. Practical advice
on such work is also provided in the Electrical Safety Code of Practice 2010 - Working Near
Exposed Live Parts. One of the requirements is that workers and plant should maintain an ‘exclusion
zone’ of three metres around live overhead power lines of up to 132kV. Powerlines on poles are
usually less than this voltage.

Greater ‘exclusion zones’ apply to high voltage lines (six and eight metres depending on the
voltage). In certain limited situations there may be exceptions to this – see the Electrical Safety
Regulation 2002 and the Electrical Safety Code of Practice 2010 – Working Near Exposed Live
Parts for details.

When operating plant near power lines a number of factors must be considered when implementing
systems to maintain the ‘exclusion zone’ from overhead power lines. These include:
(a) identifying the minimum clearance distance from the closest part of the concrete placement
boom to the power line, the ‘exclusion zone’
(b) allowing for sway and sag of the overhead lines (Sway is usually caused by wind and sag occurs
when the temperature of the line fluctuates)
(c) ensuring that persons, plant and vehicles stay outside the ‘exclusion zone’ at all times, and
(d) nominating a ‘safety observer’ when the crane or plant could enter into the ‘exclusion zone’
(where this is required by the Electrical Safety Code of Practice 2010 – Working Near Exposed
Live Parts).

PN11172 Concrete Pumping Code of Practice 2005 Page 14 of 27

The exclusion zones for Queensland Rail power lines and those of some power authorities may
differ. It is the responsibility of the principal contractor or person in control of the workplace to
check with the person in control of the overhead electric line.

There are a number of devices available that either assist in preventing contact with power lines, or
reduce the degree of risk in the event of contact. Such devices include the following.
(a) The use of ‘tiger tails’ on power lines act as a visual aid that assists in preventing contact by
highlighting the location of the power line. Only low voltage lines (under 1000 volts) can be
continuously covered with tiger tails, which leaves the higher lines on power poles (usually at
least 11,000 volts) exposed. Note: tiger tails do not insulate the wires and therefore the
‘exclusion zone’ must be maintained.
(b) Limiting or warning devices to assist in preventing the pump boom from entering the exclusion
zone. If a limiting or warning device is used, the system should be designed to ‘fail safe’ or
should at least meet category 4 reliability in accordance with AS 4024.1 Series – Safety of
Machinery or BS EN 954-1 Safety of Machinery – Safety Related Parts of Control Systems –
General Principles for Design.
(c) Earthing of concrete placing booms should be in accordance with the Electrical Safety Code of
Practice 2010 – Working Near Exposed Live Parts.

Irrespective of whether safety devices are being used, the ‘exclusion zone’ must not be
encroached.
Unloading and setting-up of concrete pumping pipes also poses a risk of contact with overhead
powerlines. Pipes should be kept parallel to the ground when setting-up near overhead powerlines.
An observer can be used to ensure that concrete booms do not come into proximity to powerlines.

Further information may be obtained in the Electrical Safety Regulation 2002 and the Electrical
Safety Code of Practice 2010 – Working Near Exposed Live Parts or on the Electrical Safety Office
website www.eso.qld.gov.au.

4.2.3 Setting-up in a public place

Before setting-up a concrete pump in a street, roadway or public place consultation should occur
regarding relevant risks between the principal contractor or person in control of the workplace and
the concrete pumper. Careful attention should be given to the following.
(a) Approvals are usually required from local councils and, these should be examined by the
concrete pumper.
(b) The public should be directed to an alternative footpath, and protective screens erected or fitted
around the pump area to prevent concrete being splashed on the public.
(c) Lane closures and other operations which require the erection of appropriate barricades and signs
should comply with the requirements of Main Roads, Local Government Authorities and any
relevant Building or Local Acts.

4.2.4 Traffic control

The person in control of the relevant workplace area will provide or arrange for adequate traffic
control, in consultation with the concrete pumper.

PN11172 Concrete Pumping Code of Practice 2005 Page 15 of 27

4.3 Tasks
4.3.1 Concrete delivery
Risk
Concrete delivery involves the delivery of concrete from the delivery truck to the concrete pump
hopper. In this operation one or more concrete trucks are reversed up to the concrete hopper to
deliver concrete. This activity poses risks to the concrete delivery truck driver, the concrete pump
operator, the allocated traffic spotter, other workers working in and around the concrete pumping
exclusion zone and members of the public.

The risks from this phase of delivery include:

 being hit or run over by a delivery truck
 entrapment between the delivery truck and hopper or between delivery trucks
 being struck by concrete whilst delivering concrete to the hopper, due to equipment failure such
as a burst line
 entanglement, crushing and amputation from the concrete hopper, and
 being struck by ejected pipes from the concrete pump due to clamp failures, whilst discharging
concrete into the hopper.

Risk control
When delivering concrete, the following should be ensured.
(a) Concrete delivery trucks should have clear and safe access to approach and leave the receiving
hopper of the pump.
(b) If more than one concrete delivery truck is required to approach the receiving hopper at any one
time, the person in control of the relevant workplace area should ensure a spotter or traffic
controller is on hand to safely direct the movement of the trucks, considering the safety of each
worker in the area.
(c) Concrete delivery trucks should not reverse into the exclusion zone if they cannot see the
nominated person for directing the truck (the spotter). The vehicle should be stopped
immediately when the driver loses sight of the nominated person directing the truck.
(d) If more than one concrete delivery truck is required to approach the receiving hopper at any one
time the person in control of the relevant workplace area should ensure:
i. a spotter or traffic controller is on hand to safely direct the movement of the trucks, and
ii. there is adequate room for the concrete delivery truck driver to operate the concrete truck
safely and in the event of an emergency have clear access to operate the concrete pump
emergency shutdown device.
(e) No person should stand between the reversing concrete delivery truck and the hopper.
(f) The concrete chute on concrete trucks should only be moved when the truck is stationary. It is
preferable for the truck driver to perform this task. If another worker carries out the task the
permission of the driver should be obtained.
(g) The concrete receiving hopper should be at a height that allows a gravity flow of concrete into
the hopper.
(h) Additional ramping may be required for the concrete delivery truck where low slump concrete is
to be used. Where ramps are used they should be specifically designed to:
i. ensure the truck cannot back off the ramps,
ii. ensure the truck remains stable, and
iii. have a non-slip surface.

PN11172 Concrete Pumping Code of Practice 2005 Page 16 of 27

(i) All concrete delivery trucks should be fitted with flashing hazard lights that are activated when
the truck is in reverse.
(j) All concrete delivery trucks should be fitted with audible reversing devices.

When delivering concrete to the pump hopper the following should be ensured:
(a) The receiving hopper of the concrete pump should be positioned so that it can receive a concrete
flow readily from the discharge chute of a concrete delivery truck.
(b) A grate is to be provided to prevent access to dangerous moving parts such as agitator
mechanisms and valve gear (“S – tube” or “rock valve”). Hopper grates designed for opening are to
be fitted with an interlock system that de-activates both the paddles and the valve gear. This system
is to ensure that there is no energy in the system that can cause movement of the agitator mechanism
or valve gear after the interlock switch is activated (i.e. from remaining hydraulic pressure in the
accumulator).
(c) The emergency stop button should be accessible by the concrete pump operator and the concrete
delivery truck driver.
(d) The grate should be constructed of parallel bars which are spaced so that it is not possible for a
person’s hand to become trapped (this spacing should not exceed 75mm).
(e) The distance from the top of the grate to any moving parts should be at least 100mm.

4.3.2 Pump and boom operation

Risk
Inexperienced or untrained operators pose a risk of unsafe operation.

Risk control
Concrete pump and boom operators should be competent to safely operate relevant equipment.
Competency is achieved through training and supervision and should be assessed by testing both
theoretical knowledge and physical operation of the machinery.

Pump and boom operators should:

(a) be familiar with manufacturer’s advice and information contained within manuals and other
documents, including hydraulic pressure relief settings and maximum rated concrete pressure
(b) operate the plant in line with the advice and information of the manufacturer
(c) carry out the daily maintenance inspection, visual inspection of the pipeline and other pre-
operational inspections in accordance with the plant operator’s manual, before pumping
commences
(d) always attend to equipment, or arrange for a alternative competent person to attend if required to
work away from the equipment
(e) pump concrete only when the hopper grate is in the closed position
(f) ensure pump flow rates match discharge rates of concrete delivery trucks
(g) be able to maintain a volume of concrete in the concrete pump hopper at levels that will not
allow air into the pump .Include specifics of how this will be achieved in the safe work method
statement (e.g. automatic shut-off if level of concrete in hopper falls too low; or additional
competent person stationed at hopper to stop the pump)
(h) follow the directions of the hose-hand, and
(i) ensure a system of communication is maintained with the hose-hand.

PN11172 Concrete Pumping Code of Practice 2005 Page 17 of 27

4.3.3 Concrete pouring
Risk
The concrete pour involves the pouring of concrete through the delivery hose connected to the
concrete pump, to the concrete pour area. In this operation there may be a risk of concrete lines
bursting, lines becoming unrestrained and pipe clamps being dislodged. Damage to delivery hose or
the inappropriate selection of the delivery hose may also cause the discharge of concrete under
pressure.

Risk control
(a) The rubber delivery hose should always be checked for damage prior to being fitted.
(b) Where the delivery hose is positioned over or above any working or public area, it should be
fitted with a suitable stop at the outlet end.
(c) Care should be taken to avoid damage to the hose during use.
(d) Ensure the delivery hose fitting on a boom pump is secured in position by a safety chain, sling or
other retaining device in accordance with AS 1418.15 Cranes (including hoists and winches) –
Concrete placing equipment.
(e) Always use a delivery hose that has a pressure rating to accommodate the pumping concrete
pressure. Steel re-enforced delivery hose should be used with high pressure pumps such as those
used on high-rise ‘satellite’ booms. As a guide, delivery hose that is not re-enforced (sometimes
called ‘rag’ or ‘fabric’ hose) should not be used on piston type pumps, unless the pumping
pressure is within the maximum allowable hose pressure rating specified by the manufacturer.
Where there is any doubt about the ability of the hose to withstand concrete pressures, written
verification from the hose manufacturer should be obtained.
(f) Additional hose added to the end of a concrete placement boom may cause structural failure of
the boom, when the hose hangs from the end of the boom and concrete is pumped through it.
Documentation should be available on site that shows the maximum size and length of hose that
may be suspended, as stated by the boom manufacturer.
(g) Reducers should be used as per the manufacturer’s recommendations to avoid overload of the
delivery hose or other parts of the unit.
(h) The hose-hand should wear eye protection complying with AS 1336 Recommended practices for
occupational eye protection.

4.3.4 Line cleaning (on site)

Risk
Line cleaning is usually performed with either high pressure water or air, to ensure the dislodgement
of residual concrete located in the pipeline. Dislodged concrete can act as a high-velocity projectile,
potentially striking both workers doing cleaning and those nearby (including members of the public).
To avoid hose whip, all reducers and rubber hose must be removed from the end of the delivery line.

This matter should be discussed by the principal contractor or person in control of the workplace and
the concrete pumper.

Risk control
A risk assessment should be performed and documented so that adequate controls are implemented
to control the risks associated with line cleaning.

PN11172 Concrete Pumping Code of Practice 2005 Page 18 of 27

When performing line cleaning the following safety precautions should be followed:
(a) Only experienced and trained pumping personnel should carryout line cleaning.
(b) Cleaning should be conducted in accordance with the manufacturer’s instructions and PCBU’s or
other duty holder’s procedures.
(c) Water should be used for cleaning in preference to air to minimise the risk of projectiles.
(d) There should always be a connection to atmosphere (air relief valve) as well as the air entry
point to the pipeline, which will allow the system to be depressurised before removing any
pipeline (never attempt to take a line apart to clean out a blockage or to dismantle it until after
the pressure has been relieved).
(e) No pipeline connection or fitting should be disconnected unless it has been established that the
pipeline is free of internal pressure.
(f) The pump operator is to remain at the pump controls while the pipeline is pressurised.
(g) Always remove the rubber delivery hose at the END of the pipeline, so that the hose can not
whip around dangerously should the line be blown out.
(h) All parts of the pipeline should be secured to prevent movement during purging.
(i) A positive catchment device or properly designed receptacle should be attached to the discharge
end of the pipeline to safely catch the cleaning device, while still allowing concrete to flow.
(j) If using a properly designed receptacle, such as a concrete truck bowl, concrete lines should be
adequately restrained from movement. Restraint by attachment to the concrete truck’s ladder is
not an adequate control.
(k) Keep all workers away from the discharge end while the concrete is under pressure.
(l) Ensure all workers involved wear adequate personal protective equipment.

4.3.5 Pump cleaning (on site)

Risk
Entanglement, crushing and amputation hazards exist in a concrete hopper and pumping device and
can injure workers who stand in or place parts of their body in hoppers. Workers should avoid
placing any part of their body within the hopper.

This matter should be discussed by the principal contractor or person in control of the workplace and
the concrete pumper.

Risk control
(a) A physical barrier to prevent a person contacting moving parts in a hopper should be fitted and
maintained at all times during operation.
(b) Where cleaning or dislodgement of material requires a worker to enter the hopper, the equipment
must be shut down and any accumulated hydraulic or air pressures exhausted that may allow the
elements to move or rotate, even with the engine stopped.
(c) Cleaning should only be done when there is another person is in the immediate vicinity to
provide assistance if required.
(d) Workers should receive adequate instruction, training and where required supervision, in
cleaning a concrete hopper.

PN11172 Concrete Pumping Code of Practice 2005 Page 19 of 27

4.3.6 Preparation for road travel
Risk
Unsecured equipment poses a risk to concrete delivery truck drivers, pedestrians and fellow
motorists. Over time unsecured equipment may be subject to increased wear which may lead to
failure.

Risk control
The manufacturer’s instruction must always be followed, particularly where the following items are
appropriate.
(a) Outriggers (whether hydraulic or manual), must be secured with a locking device specified by
the manufacturer and stowed in a travelling position to ensure that there is no lateral movement.
(b) Loose components (such as pipes, couplings and tools etc), must be stowed in appropriate
storage areas in accordance with manufacturer or other any relevant published guidelines for the
safe carriage of loads on road vehicles (e.g. Load Restraint Guide (2003) ISBN 0664 329319).
(c) Disengage all drives to hydraulic pumps (for operating the concrete pump), boom and/or
outriggers, and put the controls in the OFF position.
(d) Boom restraint should be in accordance with any instructions by the manufacturer and should
ensure there is no unintended movement of the boom.
(e) Air operated devices for ‘Engage’ and ‘Disengage’ of ‘power takeoff’ (PTO) drives must be of
an approved type and brand, and must have a positive feel for the ‘In’ and ‘Out’ position with a
warning light when engaged (if able to be operated independently).

4.4 By-products
4.4.1 Noise
Risk
Excessive noise at the workplace can cause industrial deafness, also known as noise-induced hearing
loss. The Code of Practice on Managing Noise and Preventing Hearing Loss at Work gives detailed
information on the assessment of noise in the workplace. It is recommended that this standard be
read in conjunction with the Concrete Pumping Code of Practice. Before pumping equipment is set-
up consultation should be undertaken between the principal contractor or person in control of the
workplace and the concrete pumper, regarding the risk of excessive noise.

Risk control
(a) Noise levels from machinery or equipment during pumping operations should not be a risk to
hearing or health.
(b) Suitable hearing protection equipment, and training in its maintenance and use, should be
provided to the operators of the concrete pump and other associated equipment if the noise is in
excess of the noise exposure limits.

The Regulation prescribes maximum levels for excessive noise in the workplace. These requirements
must be complied with by law and as such it is highly recommended that this part of the regulation
be read in conjunction with the Concrete Pumping Code of Practice.

4.4.2. Fumes
Risk
All fumes should be identified and assessed for risk. Of most concern are exhaust gases from the
concrete delivery truck and any internal combustion engines. Carbon monoxide is a hazardous

PN11172 Concrete Pumping Code of Practice 2005 Page 20 of 27

chemical and in large concentrations can cause permanent illness and death. An assessment of the
truck, concrete pump and associated plant location is necessary, to consider the likelihood of gas
build-up.

This matter should be discussed by the principal contractor or person in control of the workplace and
the concrete pumper.

The Regulation states requirements when exposing persons to hazardous chemicals, such as exhaust
gas fumes. The PCBU must follow these requirements.

Risk control
If possible place the truck in a position that will eliminate or reduce the build-up of exhaust gas. If it
is necessary to place the truck in an enclosed area ensure that:
(a) an adequate level of ventilation is maintained to prevent the build-up of hazardous exhaust gases,
or
(b) exhaust gases are vented to open air.

5. Inspection and maintenance

5.1 General
Appropriate ‘planned inspections’ and ‘preventative maintenance programs’ are essential for safety
and efficiency in the operation of concrete pumps and booms, and should be carried out in
accordance with the manufacturer’s recommendations, and AS 2550.15. These inspections and
routine maintenance should be carried out:
(a) daily before commencement of work
(b) weekly
(c) monthly
(d) three monthly
(e) yearly, and
(f) six yearly strip downs.

5.2 Compliance plates and certification

All equipment associated with concrete pumping must have fixed compliance plates, and/or
appropriate certification for their use, e.g.,
(a) cab and chassis – by the state transport authority in which the unit is registered, with a fixed
motor vehicle modification plate showing the appropriate modification codes
(b) placing boom and outriggers:
(i) by the manufacturer, with a fixed plate showing date of manufacture, serial number,
maximum recommended working pressure, maximum recommended length of end (or drop
hose), recommended maximum size of delivery pipe/hose, etc. in accordance with AS
1418.15 Cranes (including hoists and winches) – Concrete placing equipment
(ii) following each six year strip down, by a professional engineer whose area of competence
includes the type of work being undertaken, with a fixed plate setting out the details of the
annual inspection and the six year strip down and inspection dates, in accordance with AS
2550.15 Cranes – safe use – Concrete placing equipment
(c) concrete pump – by the manufacturer, with a fixed plate showing date of manufacture and serial
number

PN11172 Concrete Pumping Code of Practice 2005 Page 21 of 27

(d) maximum recommended working pressures for hydraulics and concrete etc, in accordance with
AS 1418.15 Cranes (including hoists and winches) – Concrete placing equipment, and
(e) Over Length and Overweight Permits must be obtained, kept current, and in the vehicle.

Any pump, boom, prime mover and/or associated equipment not having such a compliance plate or
permit, should be removed from service immediately, until such certification is effected.

5.3 Pre-operational inspections

(a) Before the start of each work period, all concrete pumping/placing equipment should be given a
visual inspection and function test – in accordance with the manufacturer’s instructions and
recommendations, and AS 2550.15 Cranes – safe use – Concrete placing equipment.
(b) Any repairs or replacements should be in accordance with the manufacturer’s recommendations
and only carried out by trained and competent personnel.
(c) Written records should be kept of maintenance and repair work performed on concrete
pumping/placing equipment.

5.4 Routine maintenance inspections

(a) The owner should establish an appropriate program of weekly, monthly and quarterly
preventative maintenance inspections of all equipment in accordance with the manufacturer’s
recommendations and AS 2550.15 Cranes – safe use – Concrete placing equipment, which is
based on the equipment’s working environment and the severity of use of the equipment.
(b) Details of these inspections are to be kept in the appropriate log book, and a copy kept in the
unit.

5.5 Annual inspections

All concrete placing booms, pumps and all other associated equipment, should be inspected once a
year by an assessor, for the suitability of continued service, in accordance with the manufacturers
specifications, and AS 2550.15 Cranes – safe use – Concrete placing equipment.

5.6 Assessment for service and continued use

All items of concrete placing equipment should also be additionally subjected to a major inspection
for assessment of continued service of the concrete placing equipment in accordance with AS
2550.15 Cranes – safe use – Concrete placing equipment.

These inspections should include a strip down of all high stress areas, including the boom, slew ring
and outriggers.

The inspection should be conducted by a professional engineer, with competence in this work, to
assess the suitability of the equipment for continued service until the next major inspection. All
inspections should be noted in the appropriate log book.

All concrete placing equipment should be assessed for service and continued use six years after the
date of manufacture and at each six year period thereafter.

PN11172 Concrete Pumping Code of Practice 2005 Page 22 of 27

5.7 Inspection report
If repairs/replacements are required (as assessed in accordance with the manufacturer’s
recommendations and/or the requirements of AS 2550.15 Cranes – safe use – Concrete placing
equipment), then the plant owner should ensure that a record of the repair/replacement action
required, together with the reason, is recorded in the log book. If no action is taken, or the equipment
continues to fail to meet the assessment criteria, then the inspector may order that the equipment be
removed from service immediately.

5.8 Welding and other repairs

Only a welder or service provider holding the appropriate qualifications, and where possible in
possession of the manufacturer’s current specifications may perform welding or repair work on the
concrete pump or any associated equipment (including the placing boom, the outrigger system or any
other stressed structural component that is related to the overall equipment stability or structural
integrity).

5.9 Reporting defects

(a) A pump operator should report defects immediately.
(b) If a defect is considered to be a hazard to safety, pumping operations should be stopped until the
defect is repaired.
(c) The details of reported defects and subsequent action taken should be entered into a log book.

5.10 Log books and inspection record sheets

(a) Instruction manuals should accompany the pump unit and/or boom, which give sufficient
instructions for operation, maintenance and repairs.
(b) Maintenance and repair manuals are to be kept in a safe place at the registered premises, and
should include a parts catalogue.
(c) The operator should be familiar with the contents of the instruction manual which should be
available at the site of operation.
(d) All manuals should be kept up-to-date with any additional information from the manufacturer.
(e) Maintenance log books are to be kept up-to-date, on the pump, and be available on request at the
workplace.
(f) All log books and inspection record sheets are to show complete details of all inspections, tests,
repairs, replacements and modifications carried out on equipment, in accordance with AS
2550.15 Cranes – safe use – Concrete placing equipment.
(g) Evidence that the pump and associated equipment has been inspected and certified as ‘suitable
for continued service’ (i.e. in a safe working condition), should accompany the unit, and be made
available to the principal contractor or person in control of the workplace for inspection (on
request), before the unit is allowed to operate on site.
(h) Similarly, up-to-date log books & inspection record sheets should accompany the unit and also
be available for inspection by the principal contractor or person in control of the workplace.

5.11 Warning and safety signs

Ensure that all warning and safety signs/stickers are in good condition, legible and positioned on all
equipment (after being inspected and found to be serviceable), in accordance with AS 2550.15
Cranes – safe use – Concrete placing equipment.

PN11172 Concrete Pumping Code of Practice 2005 Page 23 of 27

5.12 Pipe testing, identification and marking
(a) Pipe wall thickness should be tested in accordance with AS 2550.15 Cranes – safe use –
Concrete placing equipment.
(b) Ultrasonic testing may not be appropriate for a twin wall pipeline. Other suitable testing methods
should be adopted such as the use of thickness testing callipers, increased inspection and
increased monitoring of use, in terms of volume and type of concrete pumped.
(c) Piping with a wall thickness less than the recommended thickness for the pumping design
pressure should not be used.
(d) All pipeline segments should be clearly identified with a permanently fixed unique identification
mark or number, prior to being placed in service, showing the details required in accordance
with AS 1418.15 Cranes (including hoists and winches) – Concrete placing equipment.
(e) The pipe log book shall record wall thickness and pressure details, in accordance with AS
1418.15 Cranes (including hoists and winches) – Concrete placing equipment.

6. Safety equipment
6.1 Provision of personal protective equipment (PPE)
Personal protective equipment is the least effective method for controlling risk, however in many
circumstances associated with the pumping of concrete this is the most practicable option. Before
beginning any pumping operation, the concrete pump operator and the principal contractor or person
in control of the workplace, should assess the conditions likely to affect the health and safety of
workers and arrange for the provision and use of appropriate personal protective equipment.

The following items of PPE are required when pumping concrete:

(a) safety helmets
(b) eye protection
(c) safety vest
(d) rubber safety boots.

The following items of PPE may also be required when pumping concrete:
(e) hearing protection
(f) gloves.

6.2 Additional equipment

Each pump unit should be equipped with the following items.
(a) first aid kit (must include eye wash)
(b) protective creams
(c) fire extinguishers (as appropriate)
(d) sufficient reflective traffic cones (minimum 450mm high), and
(e) signs e.g. exclusion zone and use of high visibility vests.

7. Training and supervision

The overall object of the Act is to prevent a person’s death, injury or illness being caused by a
workplace, by a relevant workplace area, by work activities, or by plant or substances for use at a
workplace.

PN11172 Concrete Pumping Code of Practice 2005 Page 24 of 27

PCBUs have duties under the Act which include providing information, instruction, training and
supervision to workers and others at a workplace. These duties ensure workers perform their work in
a manner that is safe and without risk to health.

Information, training, and instruction should cover at least:

(a) the work methods to be used in the setting up and safe operation of concrete placing booms and
pumps
(b) the method for inspection and maintenance of concrete pumping equipment
(c) a knowledge of the manufacturer’s operation and service manuals
(d) the correct use, care and storage of personal protective equipment
(e) the correct use, care and storage of tools and equipment to be used, including electrical safety
practices, and
(f) procedures to be adopted in the event of accident or injury.

Supervision must:
(a) ensure that only those workers who have received training and instruction are authorised to carry
out that work, and
(b) include sufficient monitoring of the work to ensure that agreed safe work practices are being
adhered to, including the use of all protection systems and personal protection equipment.

PN11172 Concrete Pumping Code of Practice 2005 Page 25 of 27

Appendix 1: Dictionary
Australian Standard means a standard, rule, code or specification of the Standards Association of
Australia.

Clean out adaptor means a short length of pipe with one end blanked off and connections for a
water or air hose coupled to the pipeline for cleaning purposes. It should have a separate air relief
valve vented to atmosphere and a pressure gauge when used with compressed air.

Competent person means a person who the concrete pumper ensures (prior to appointment), has
current skills and knowledge through either training, qualification, or experience or a combination of
those, who is industry based, and who may have obtained training certification from the appropriate
manufacturer to have the knowledge and skill to enable that person to correctly perform the task
required.

Concrete pumper means the PCBU of a concrete pumping business engaged by a principal
contractor, subcontractor or person in control of a workplace to pump concrete.

Concrete pumping pressure means the pressure exerted by the pump on the concrete at the piston
head.

Condition of tipping means a pump should be considered to be in the condition of tipping when the
stability moment equals the overturning moment.

Coupling system means the connecting sections of a delivery pipeline.

Delivery hose means a flexible hose used in or at the end of the pipeline.

Delivery pipeline means a portable rigid or flexible piping system supplied in sections with the
provision for joining together with a coupling system.

Employee representative means an employee, member of a health and safety committee or a person
elected by the employees at a place of work to represent them on health and safety matters.

Hose whip means the uncontrolled and rapid motion of the flexible rubber hose on the end of a
concrete placement boom or other concrete delivery line.

Outriggers means extendible structural members on the pump unit to increase the dimensions of the
base to ensure the stability of the pump in set up, dismantling and use.

PCBU means person conducting a business or undertaking. See Work Health and Safety Act 2011.

Placing boom means a powered device to support and position a concrete delivery pipeline, which
may incorporate folding, luffing, extending and/or slewing motions.

Principal contractor. See Work Health and Safety Regulation 2011.

PN11172 Concrete Pumping Code of Practice 2005 Page 26 of 27

Professional engineer means a person eligible for membership of the Institution of Engineers
Australia or a Professional Engineer of Queensland.

Pump unit means the concrete pump, placing booms and associated equipment.

Reducer means a pipe that changes the internal diameter of the pipeline.

Relevant workplace area means:

(a) any place, or a part of a place, used as a workplace, and
(b) any area adjacent to the place or part associated with the use of the place or part as a workplace.

Examples of areas that could be adjacent to a place or part and associated with its use as a
workplace—
1. shopping centre car park
2. common area in a shopping centre
3. hotel beer garden, and
4. outside play area for a child care centre.

PN11172 Concrete Pumping Code of Practice 2005 Page 27 of 27