सीईडी/CED

कार्य र्ोजना

(01 अप्रैल 2021 तक )

PROGRAMME OF WORK
(As on 01 April 2021)

सससिल इं जीसनर्र ं ग सिभाग

(सीईडी)
Civil Engineering Department
(CED)

भा तीर् मानक ब्‍र्ू ो

मानक भिन, 9 बहादु शाह ज़फ मागय
नई ददल्‍ली– 110 002

BUREAU OF INDIAN STANDARDS

MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG

NEW DELHI 110002

Website: www.bis.gov.in
 PREFACE
This Programme of Work, prepared every year for Civil Engineering Division
Council, CEDC, indicates the latest position of published Indian Standards and draft
standards at different stages under CEDC, as on 01 April 2021. The present scope of
CEDC is as follows:

‘Standardization in the field of Civil Engineering including structural

engineering; building materials and components; planning, design, construction
and maintenance of civil engineering structures and built environment;
construction practices, and safety in building; but excluding those subjects
which specifically relate to Water Resources Development and Management’.

The Division Council is working towards achieving the above goal through 36
Sectional Committees covering wide range of subjects from basic building materials,
design and construction to very high technical areas like offshore installations, ports
and harbours, cyclone resistant structures, etc.

Standards, Special Publications/Handbooks and drafts thereof are listed under

respective Sectional Committees, a list of which is given in the Table of Contents, to
serve as a key for easy location. Under each committee, the scope of work of the
committee, and the corresponding Technical Committee (TC), Subcommittee (SC)
and Project Committee (PC) of the International Organization for Standardization
(ISO), if any, are also listed with the status of membership. The letter ‘P’ after the ISO
Committee number indicates that India is a ‘Participating’ member and letter ‘O’
indicates its ‘Observer’ member status on the concerned technical committee of ISO .

If you need further information, please write to:

Head (Civil Engg)

Bureau of Indian Standards
Manak Bhavan
9 Bahadur Shah Zafar Marg
NEW DELHI 110 002

Phone: 011 – 2323 5529

e-mail: [email protected]
Website: www.bis.gov.in

For periodic update of this Programme of Work, kindly refer BIS website, www.bis.gov.in.
For online purchase of BIS publications, please visit https://standardsbis.bsbedge.com/

Disclaimer: BIS is not responsible for any inadvertent error that may have crept in, in the information published in this
publication. The information published herein is for immediate information only and no legal claim can be made for
any damage caused by using the content of this publication. BIS reserves the right to change the information
published herein, or in its website at any point of time without further notification. For latest information of standards,
kindly refer the Programme of Work listed in the BIS website under the tab ‘Standardization' —-> 'Published
Standards', which lists the as on date standards published and those under development.

1
 CIVIL ENGINEERING DEPARTMENT
Committee Title of the Committee
No.

CED 02 CEMENT AND CONCERTE SECTIONAL COMMITTEE

CED 03 SANITARY APPLIANCES AND WATER FITTINGS SECTIONAL COMMITTEE
CED 04 BUILDING LIMES AND GYPSUM PRODUCTS SECTIONAL COMMITTEE
CED 05 FLOORING, WALL FINISHING AND ROOFING SECTIONAL COMMITTEE
CED 06 STONES SECTIONAL COMMITTEE
CED 07 STRUCTURAL ENGINEERING AND STRUCTURAL SECTIONS SECTIONAL COMMITTEE
CED 09 TIMBER AND TIMBER STORES SECTIONAL COMMITTEE
CED 11 DOORS, WINDOWS AND SHUTTERS SECTIONAL COMMITTEE
CED 12 FUNCTIONAL REQUIREMENTS IN BUILDINGS SECTIONAL COMMITTEE
CED 13 BUILDING CONSTRUCTION PRACTICES SECTIONAL COMMITTEE
CED 15 BUILDER’S HARDWARE SECTIONAL COMMITTEE
CED 20 WOOD AND OTHER LIGNOCELLULOSIC PRODUCTS SECTIONAL COMMITTEE
CED 22 FIRE FIGHTING SECTIONAL COMMITTEE
CED 24 PUBLIC HEALTH ENGINEERING SECTIONAL COMMITTEE
CED 29 CONSTRUCTION MANAGEMENT (INCLUDING SAFETY IN CONSTRUCTION) SECTIONAL
COMMITTEE
CED 30 CLAY AND STABILIZED SOIL PRODUCTS FOR CONSTRUCTION SECTIONAL COMMITTEE
CED 35 FURNITURE SECTIONAL COMMITTEE
CED 36 FIRE SAFETY SECTIONAL COMMITTEE
CED 37 STRUCTURAL SAFETY SECTIONAL COMMITTEE
CED 38 SPECIAL STRUCTURES SECTIONAL COMMITTEE
CED 39 EARTHQUAKE ENGINEERING SECTIONAL COMMITTEE
CED 41 WATER PROOFING AND DAMP-PROOFING SECTIONAL COMMITTEE
CED 43 SOIL AND FOUNDATION ENGINEERING SECTIONAL COMMITTEE
CED 44 METHODS OF MEASUREMENT OF WORKS OF CIVIL ENGINEERING (EXCLUDING WATER
RESOURCES DEVELOPMENT) SECTIONAL COMMITTEE
CED 46 NATIONAL BUILDING CODE SECTIONAL COMMITTEE
CED 47 PORTS, HARBOURS AND OFFSHORE INSTALLATIONS SECTIONAL COMMITTEE
CED 48 ROCK MECHANICS SECTIONAL COMMITTEE
CED 50 PLASTIC PIPING SYSTEMS SECTIONAL COMMITTEE
CED 51 PLANNING, HOUSING AND PREFABRICATED CONSTRUCTION SECTIONAL COMMITTEE
CED 53 CEMENT MATRIX PRODUCTS SECTIONAL COMMITTEE
CED 54 CONCRETE REINFORCEMENT SECTIONAL COMMITTEE
CED 55 SIEVES, SIEVING AND OTHER SIZING METHODS SECTIONAL COMMITTEE
CED 56 HILL AREA DEVELOPMENT ENGINEERING SECTIONAL COMMITTEE
CED 57 CYCLONE RESISTANT STRUCTURES SECTIONAL COMMITTEE
CED 58 SUSTAINABILITY OF BUILT ENVIRONMENT SECTIONAL COMMITTEE
CED 59 SMART CITIES SECTIONAL COMMITTEE
ANNEX I STANDARDS WITHDRAWN/SUPERSEDED
ANNEX II LIST OF IS WITH DUAL NUMBER/EQUIVALENT STANDARDS/HARMONIZED WITH OTHER
STANDARDS ORGANIZATION LIKE II A, II B, II C etc.
ANNEX III LIST OF IS NO. COVERED UNDER BIS CERTIFICATION MARKS SCHEME
ANNEX IV INDIAN STANDARDS WITH ECO MARK PROVISIONS
ANNEX V BILINGUAL STANDARDS
ANNEX VI MEMBERSHIP STATUS IN ISO TC/SCs
ANNEX VII LIST OF MANDATORY STANDARDS
ANNEX VIII LIST OF IS TRANSFERRED TO OTHER DEPARTMENTS
ANNEX IX LIST OF SPECIAL PUBLICATIONS

2
 ASPECTWISE BREAKUP OF STANDARDS (As on 01 April 2021)

Committee Product Code of Methods Terminology Dimensions System Safety Others Total
No. Specification Practice of Tests (T) (D) Standard Standard (O)
(S) (C) (M)

CED 02 56 22 65 14 1 0 0 2 160
CED 03 68 1 2 0 0 0 0 0 71
CED 04 21 14 14 2 0 0 0 0 51
CED 05 28 21 23 2 0 0 0 3 77
CED 06 9 2 16 1 0 0 0 13 41
CED 07 20 18 0 0 7 0 1 14 60
CED 09 82 17 25 2 0 0 0 10 136
CED 11 22 2 1 1 0 0 0 1 27
CED 12 1 17 3 1 0 0 0 2 24
CED 13 10 67 6 3 1 0 0 15 102
CED 15 43 0 0 0 0 0 0 0 43
CED 20 47 7 16 0 0 0 0 0 70
CED 22 97 18 1 1 0 0 0 30 147
CED 24 24 34 1 1 0 0 0 1 61
CED 29 0 21 0 0 0 0 17 3 41
CED 30 20 6 6 2 0 0 0 1 35
CED 35 45 2 13 1 2 0 0 0 63
CED 36 4 28 11 1 0 0 0 4 48
CED 37 0 5 0 0 0 0 0 1 6
CED 38 0 9 0 0 0 0 1 1 11
CED 39 0 14 0 0 0 0 0 0 14
CED 41 12 12 11 1 0 0 0 0 36
CED 43 18 38 66 2 0 0 0 2 126
CED 44 0 0 0 0 0 0 0 29 29
CED 46 0 0 0 0 0 0 0 1 1
CED 47 0 9 0 1 0 0 0 1 11
CED 48 0 19 27 1 0 0 0 5 52
CED 50 57 4 2 0 0 0 0 3 66
CED 51 8 35 0 3 0 0 0 0 46
CED 53 43 9 23 1 0 0 16 0 92
CED 54 14 1 2 0 0 0 0 0 17
CED 55 8 1 5 4 0 0 0 0 18
CED 56 0 13 0 0 0 0 0 0 13
CED 57 0 3 0 0 0 0 0 0 3
CED 58 0 0 0 0 0 0 0 1 1
CED 59 0 2 0 1 0 0 0 1 4

TOTAL 757 471 339 46 11 0 35 144 1803

3
CED 02 CEMENT AND CONCRETE
SCOPE STANDARDIZATION IN THE FIELD OF ALL TYPES OF CEMENT, POZZOLANA, TESTING
SAND, CONCRETE, AGGREGATES, INSTRUMENTS FOR CEMENT AND CONCRETE
TESTING, CEMENT PLANT MACHINERY AND FERROCEMENT

LIAISON ISO/TC 71 (P) CONCRETE, REINFORCED CONCRETE AND PRESTRESSED CONCRETE

ISO/TC 71/SC 1 (P) TEST METHODS FOR CONCRETE
ISO/TC71/SC 3 (P) CONCRETE PRODUCTION AND EXECUTION OF CONCRETE
STRUCTURES
ISO/TC 71/SC 4 (P) PERFORMANCE REQUIREMENTS FOR STRUCTURAL CONCRETE
ISO/TC 71/SC 5 (P) SIMPLIFIED DESIGN STANDARD FOR CONCRETE STRUCTURES
ISO/TC 71/SC 6 (P) NON-TRADITIONAL REINFORCING MATERIALS FOR CONCRETE
STRUCTURES
ISO/TC 71/SC 7 (P) MAINTENANCE AND REPAIR OF CONCRETE STRUCTURES
ISO/TC 71/SC 8 (P) ENVIRONMENT MANAGEMENT FOR CONCRETE AND CONCRETE
STRUCTURES
ISO/TC 74 (P) CEMENT AND LIME

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

1 IS 269:2015 Ordinary Portland cement ― Specification Dec 2020 S

(sixth revision)

2 IS 383:2016 Coarse and fine aggregates for concrete ― Jan 2021 2 S

Specification (third revision)

3 IS 455:2015 Portland slag cement ― Specification Dec 2020 1 S

(fifth revision)
4 IS 456:2000 Plain and reinforced concrete ― Code of practice Feb 2021 5 C
(fourth revision)

5 IS 457:1957 Code of practice for general construction of plain Apr 2019 C

and reinforced concrete for dams and other
massive structures

6 *IS 516:1959 Methods of tests for strength of concrete Oct 2018 2 M

7 IS 516 (Part 1/Sec 1): Hardened concrete ― Methods of test: M

2021 Part 1 Testing of strength of hardened concrete:
Section 1 Compressive, flexural and split tensile
strength (first revision)

8 IS 516 (Part 2/Sec 1): Hardened concrete ― Methods of test: 2 M

2018 Part 2 Properties of hardened concrete other than
strength: Section 1 Density of hardened concrete
and depth of water penetration under pressure
(first revision)

9 IS 516 (Part 2/Sec 2): Hardened concrete ― Methods of test: M

2020 Part 2 Properties of hardened concrete other than
strength: Section 2 Initial surface absorption
(first revision)

10 IS 516 (Part 2/ Sec 4): Hardened concrete ― Methods of test: M

2021 Part 2 Properties of hardened concrete other than
strength: Section 4 Determination of the
carbonation resistance by accelerated
carbonation method (first revision)

4
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

11 IS 516 (Part 4):2018 Hardened concrete ― Methods of test: M

Part 4 Sampling, preparing and testing of
concrete cores (first revision)

12 IS 516 (Part 5/Sec 1): Hardened Concrete ― Methods of test: 1 M

2018 Part 5 Non-destructive testing of concrete:
Section 1 Ultrasonic pulse velocity testing
(first revision)

13 IS 516 (Part 5/ Sec 2): Hardened concrete ― Method of test: Part 5 Non- M
2021 destructive testing: Section 2 Half-Cell Potentials
of uncoated reinforcing steel in concrete
(first revision)

14 IS 516 (Part 5/Sec 3): Hardened concrete ― Methods of test: Part 5 M

2021 Non-destructive testing of concrete:
Section 3 Carbonation depth test (first revision)

15 IS 516 (Part 5/Sec 4): Hardened concrete ― Methods of test: Part 5 M

2020 Non-destructive testing of concrete:
Section 4 Rebound hammer test (first revision)

16 IS 516 (Part 6):2020 Hardened concrete ― Methods of test: M

Part 6 Determination of drying shrinkage and
moisture movement of concrete samples
(first revision)

17 IS 516 (Part 8/Sec 1): Hardened concrete ― Methods of test: M

2020 Part 8 Determination of modulus of elasticity:
Section 1 Static modulus of elasticity and
poisson’s ratio in compression (first revision)

18 IS 516 (Part 11):2020 Hardened Concrete ― Methods of test: M

Part 11 Determination of Portland cement content
of hardened hydraulic cement concrete
(first revision)

19 IS 650:1991 Standard sand for testing cement ― Specification Oct 2018 1 S

(second revision)

20 *IS 1199:1959 Methods of sampling and analysis of concrete Oct 2018 M

21 IS 1199 (Part 1):2018 Fresh Concrete – Methods of sampling, testing M

and analysis: Part 1 Sampling of fresh concrete
(first revision)

22 IS 1199 (Part 2):2018 Fresh Concrete – Methods of sampling, testing M

and analysis: Part 2 Determination of consistency
of fresh concrete (first revision)

23 IS 1199 (Part 3):2018 Fresh Concrete – Methods of sampling, testing M

and analysis: Part 3 Determination of density of
fresh concrete (first revision)

24 IS 1199 (Part 4):2018 Fresh Concrete – Methods of sampling, testing M

and analysis: Part 4 Determination of air content
of fresh concrete (first revision)

5
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

25 IS 1199 (Part 5):2018 Fresh Concrete – Methods of sampling, testing M

and analysis: Part 5 Making and curing of test
specimens (first revision)

26 IS 1199 (Part 6):2018 Fresh Concrete – Methods of sampling, testing M

and analysis: Part 6 Tests on fresh self
compacting concrete (first revision)

27 IS 1199 (Part 7):2018 Fresh Concrete – Methods of sampling, testing M

and analysis: Part 7 Determination of setting time
of concrete by penetration resistance
(first revision)

28 IS 1343:2012 Prestressed concrete ― Code of practice Nov 2017 1 C

(second revision)

29 IS 1344:1981 Specification for calcined clay pozzolana Oct 2018 1 S

(second revision)

30 IS 1489 (Part 1):2015 Portland pozzolana cement ― Specification: Dec 2020 1 S

Part 1 Flyash based (fourth revision)

31 IS 1489 (Part 2):2015 Portland pozzolana cement ― Specification: Dec 2020 S

Part 2 Calcined clay based (fourth revision)

32 IS 1727:1967 Methods of test for pozzolanic materials Oct 2018 2 M

(first revision)

33 IS 2386 (Part 1):1963 Methods of test for aggregates for concrete: Apr 2016 4 M
Part 1 Particle size and shape

34 IS 2386 (Part 2):1963 Methods of test for aggregates for concrete: Apr 2016 1 M
Part 2 Estimation of deleterious materials and
organic impurities

35 IS 2386 (Part 3):1963 Methods of test for aggregates for concrete: Apr 2016 1 M
Part 3 Specific gravity, density, voids, absorption
and bulking

36 IS 2386 (Part 4):1963 Methods of test for aggregates for concrete: Apr 2016 3 M
Part 4 Mechanical properties

37 IS 2386 (Part 5):1963 Methods of test for aggregates for concrete: Apr 2016 M
Part 5 Soundness

38 IS 2386 (Part 6):1963 Methods of test for aggregates for concrete: Apr 2016 M
Part 6 Measuring mortar making properties of fine
aggregate

39 IS 2386 (Part 7):1963 Methods of test for aggregates for concrete: Apr 2016 M
Part 7 Alkali aggregate reactivity

40 IS 2386 (Part 8):1963 Methods of test for aggregates for concrete: Apr 2016 1 M
Part 8 Petrographic examination

41 IS 2430:1986 Methods for sampling of aggregates for concrete Apr 2019 M

(first revision)

6
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

42 IS 2502:1963 Code of practice for bending and fixing of bars for Oct 2018 C
concrete reinforcement

43 IS 2645:2003 Integral waterproofing compounds for cement Apr 2017 S

mortar and concrete ― Specification
(second revision)

44 IS 2770 (Part 1):1967 Methods of testing bond in reinforced concrete: Feb 2017 M
Part 1 Pull-out test

45 IS 3085:1965 Method of test for permeability of cement mortar Apr 2016 M

and concrete

46 IS 3370 (Part 1):2021 Concrete structures for retaining aqueous liquids C

― Code of practice: Part 1 General requirements
(second revision)

47 IS 3370 (Part 2):2021 Concrete structures for retaining aqueous liquids C

― Code of practice: Part 2 Plain and reinforced
concrete (second revision)

48 IS 3370 (Part 3):2021 Concrete structures for retaining aqueous liquids C

― Code of practice: Part 3 Prestressed concrete
(first revision)

49 IS 3370 (Part 4/ Sec 1): Concrete structures for retaining aqueous liquids C
2021 — Code of Practice: Part 4 Design tables:
Sec 1 Plates (first revision)

50 IS 3370 (Part 4/Sec 2): Concrete structures for retaining aqueous liquids C
2021 — Code of Practice: Part 4 Design tables:
Sec 2 Rectangular tanks (first revision)

51 IS 3370 (Part 4/Sec 3): Concrete structures for retaining aqueous liquids C
2021 — Code of Practice: Part 4 Design Tables:
Sec 3 Circular tanks (first revision)

52 IS 3466:1988 Specification for masonry cement Oct 2018 5 S

IS 3466:1988 (B) (second revision)

53 IS 3535:1986 Methods of sampling hydraulic cements Oct 2018 M

(first revision)

54 IS 3558:1983 Code of practice for use of immersion vibrators for Oct 2018 C
consolidating concrete (first revision)

55 IS 3812 (Part 1):2013 Pulverized fuel ash ― Specification: Part 1 For Nov 2017 S
use as pozzolana in cement, cement mortar and
concrete (third revision)

56 IS 3812 (Part 2):2013 Pulverized fuel ash ― Specification: Part 2 For Nov 2017 S
use as admixture in cement mortar and concrete
(third revision)

57 IS 4031 (Part 1):1996 Methods of physical tests for hydraulic cement: Feb 2021 M
Part 1 Determination of fineness by dry sieving
(second revision)

7
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

58 IS 4031 (Part 2):1999 Methods of physical tests for hydraulic cement: Oct 2018 2 M
Part 2 Determination of fineness by Blaine air
permeability method (second revision)

59 IS 4031 (Part 3):1988 Methods of physical tests for hydraulic cement: Apr 2019 2 M
Part 3 Determination of soundness (first revision)

60 IS 4031 (Part 4):1988 Methods of physical tests for hydraulic cement: Apr 2019 2 M
Part 4 Determination of consistency of standard
cement paste (first revision)

61 IS 4031 (Part 5):1988 Methods of physical tests for hydraulic cement: Apr 2019 2 M
Part 5 Determination of initial and final setting
times (first revision)

62 IS 4031 (Part 6):1988 Methods of physical tests for hydraulic cement: Apr 2019 4 M
Part 6 Determination of compressive strength of
hydraulic cement other than masonry cement
(first revision)

63 IS 4031 (Part 7):1988 Methods of physical tests for hydraulic cement: Apr 2019 1 M
Part 7 Determination of compressive strength of
masonry cement (first revision)

64 IS 4031 (Part 8):1988 Methods of physical tests for hydraulic cement: Apr 2019 1 M
Part 8 Determination of transverse and
compressive strength of plastic mortar using
prism (first revision)

65 IS 4031 (Part 9):1988 Methods of physical tests for hydraulic cement: Apr 2019 M
Part 9 Determination of heat of hydration
(first revision)

66 IS 4031 (Part 10):1988 Methods of physical tests for hydraulic cement: Apr 2019 1 M
Part 10 Determination of drying shrinkage
(first revision)

67 IS 4031 (Part 11):1988 Methods of physical tests for hydraulic cement: Apr 2019 M
Part 11 Determination of density (first revision)

68 IS 4031 (Part 12):1988 Methods of physical tests for hydraulic cement: Apr 2019 2 M
Part 12 Determination of air content of hydraulic
cement mortar (first revision)

69 IS 4031 (Part 13):1988 Methods of physical tests for hydraulic cement: Apr 2019 1 M
Part 13 Measurement of water retentivity of
masonry cement (first revision)

70 IS 4031 (Part 14):1989 Hydraulic cement ― Methods of physical tests: Apr 2019 1 M
Part 14 Determination of false set

71 IS 4031 (Part 15):1991 Methods of physical tests for hydraulic cement: Apr 2019 M
Part 15 Determination of fineness by wet sieving

72 IS 4032:1985 Method of chemical analysis of hydraulic cement Apr 2019 2 M

(first revision)

8
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

73 IS 4305:1967 Glossary of terms relating to pozzolana Apr 2019 T

74 IS 4634:1991 Batch-type concrete mixers ― Methods for testing Apr 2019 M

performance (first revision)

75 IS 4845:1968 Definitions and terminology relating to hydraulic Oct 2018 T

cement

76 IS 4926:2003 Ready-mixed concrete ― Code of practice Apr 2017 1 C

(second revision)

77 IS 5512:1983 Specification for flow table for use in tests of Oct 2018 S
hydraulic cement sand pozzolanic materials
(first revision)

78 IS 5513:1996 Vicat apparatus ― Specification Feb 2021 S

(second revision)

79 IS 5514:1996 Apparatus used in ‘Le-Chatelier’ test ― Feb 2021 S

Specification (first revision)

80 IS 5515:1983 Specification for compacting factor apparatus Oct 2018 S

(first revision)

81 IS 5516:1996 Variable flow type air-permeability apparatus Feb 2021 S

(Blaine type) ― Specification (first revision)

82 IS 5525:1969 Recommendations for detailing of reinforcement Oct 2018 C

in reinforced concrete works

83 IS 5536:1969 Specification for constant flow type air- Apr 2019 S

permeability apparatus (Lea and Nurse type)

84 IS 5816:1999 Splitting tensile strength of concrete ― Method of Oct 2018 M

test (first revision)

85 IS 6452:1989 High alumina cement for structural use ― Apr 2019 5 S

IS 6452:1989 (B) Specification (first revision)

86 IS 6461 (Part 1):1972 Glossary of terms relating to cement concrete: Apr 2016 T
Part 1 Concrete aggregates

87 IS 6461 (Part 2):1972 Glossary of terms relating to cement concrete: Apr 2016 T
Part 2 Materials (other than cement and
aggregate)

88 IS 6461 (Part 3):1972 Glossary of terms relating to cement concrete: Apr 2016 T
Part 3 Concrete reinforcement

89 IS 6461 (Part 4):1972 Glossary of terms relating to cement concrete: Apr 2016 T
Part 4 Types of concrete

90 IS 6461 (Part 5):1972 Glossary of terms relating to cement concrete: Apr 2016 T
Part 5 Formwork for concrete

91 IS 6461 (Part 6):1972 Glossary of terms relating to cement concrete: Apr 2016 T
Part 6 Equipment, tools and plant

9
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

92 IS 6461 (Part 7):1973 Glossary of terms relating to cement concrete: Apr 2016 T
Part 7 Mixing, laying, compaction, curing and
other construction aspects

93 IS 6461 (Part 8):1973 Glossary of terms relating to cement concrete: Apr 2016 T
Part 8 Properties of concrete

94 IS 6461 (Part 9):1973 Glossary of terms relating of cement concrete: Apr 2016 T
Part 9 Structural Aspects

95 IS 6461 (Part 10):1973 Glossary of terms relating to cement concrete: Apr 2016 T
Part 10 Tests and testing apparatus

96 IS 6461 (Part 11):1973 Glossary of terms relating to cement concrete: Apr 2016 T
Part 11 Prestressed concrete

97 IS 6461 (Part 12):1973 Glossary of terms relating to cement concrete: Apr 2016 T
Part 12 Miscellaneous

98 IS 6491:1972 Method of sampling fly ash Feb 2021 1 M

99 IS 6909:1990 Supersulphated cement ― Specification Feb 2021 5 S

(first revision)

100 IS 6925:1973 Methods of test for determination of water soluble Oct 2018 M
chlorides in concrete admixtures

101 IS 7246:1974 Recommendations for use of table vibrators for Oct 2018 C
consolidating concrete

102 IS 7320:1974 Specification for concrete slump test apparatus Oct 2018 1 S

103 IS 7325:1974 Specification for apparatus for determining Oct 2018 S

constituents of fresh concrete

104 IS 7861 (Part 1):1975 Code of practice for extreme weather concreting: Apr 2016 1 C
Part 1 Recommended practice for hot weather
concreting

105 IS 7861 (Part 2):1981 Code of practice for extreme weather concreting: Apr 2016 1 C
Part 2 Recommended practice for cold weather
concreting

106 IS 8041:1990 Rapid hardening Portland cement ― Specification Apr 2019 4 S

(second revision)

107 IS 8042:2015 White Portland cement ― Specification Dec 2020 S

(third revision)

108 IS 8043:1991 Hydrophobic Portland cement ― Specification Apr 2019 3 S

(second revision)

109 IS 8125:1976 Dimensions and materials of cement rotary kilns, Oct 2018 D
components and auxiliaries (dry process with
suspension preheater)

110 IS 8142:1976 Method of test for determining setting time of Apr 2016 M
concrete by penetration resistance

10
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

111 IS 8229:1986 Specification for oil-well cement (first revision) Oct 2018 6 S

112 IS 8425:1977 Code of practice for determination of specific Feb 2021 C

surface area of powders by air permeability
methods

113 IS 9012:1978 Recommended practice for shotcreting Apr 2016 1 C

114 IS 9013:1978 Method of making, curing and determining Oct 2018 1 M

compressive strength of accelerated-cured
concrete test specimens

115 IS 9103:1999 Concrete admixtures ― Specification Oct 2018 2 S

(first revision)

116 IS 9142 (Part 1):2018 Artificial light weight aggregates for concrete — S
Specification: Part 1 For concrete masonry blocks
and for applications other than for structural
concrete (first revision)

117 IS 9142 (Part 2):2018 Artificial light weight aggregates for concrete — S
Specification: Part 2 Sintered fly ash coarse
aggregate (first revision)

118 IS 9284:1979 Method of test for abrasion resistance of concrete Apr 2016 M

119 IS 9376:1979 Specification for apparatus for measuring Oct 2018 S

aggregate crushing value and ten percent fines
value

120 IS 9377:1979 Specification for apparatus for aggregate impact Oct 2018 S
value

121 IS 9399:1979 Specification for apparatus for flexural testing of Oct 2018 S
concrete

122 IS 9459:1980 Specification for apparatus for use in Oct 2018 2 S

measurement of length change of hardened
cement paste, mortar and concrete

123 IS 9799:1981 Specification for pressure meter for determination Oct 2018 S
of air content of freshly mixed concrete

124 IS 10070:1982 Specification for machine for abrasion testing of Oct 2018 S
coarse aggregates

125 IS 10078:1982 Specification for jolting apparatus for testing Oct 2018 S
cement

126 IS 10079:1982 Specification for cylindrical metal measures for Oct 2018 S
use in tests of aggregates and concrete

127 IS 10080:1982 Specification for vibration machine Oct 2018 5 S

128 *IS 10086:1982 Specification for moulds for use in tests of cement Oct 2018 5 S
and concrete

129 IS 10262:2019 Concrete mix proportioning ― Guidelines C

(second revision)

11
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

130 IS 10510:1983 Specification for vee-bee consistometer Oct 2018 S

131 IS 10850:1984 Specification for apparatus for measurement of Oct 2018 S

water retentivity of masonry cement

132 IS 10890:1984 Specification for planetary mixer used in tests of Oct 2018 S
cement and pozzolana

133 IS 11262:1985 Specification for calorimeter for determination of Oct 2018 S

heat of hydration of hydraulic cement

134 IS 11263:1985 Specification for cylinder measures for Oct 2018 S

determination of air content of hydraulic cement
mortar

135 IS 11578:1986 Method for determination of specific surface area Apr 2016 M
of powders and porous particles using low
temperature gas absorption techniques

136 IS 11993:1987 Code of practice for use of screed board concrete Oct 2018 C
vibrators

137 IS 12089:1987 Specification for granulated slag for the Oct 2018 S
manufacture of Portland slag cement

138 IS 12119:1987 General requirements for pan mixers for concrete Oct 2018 S

139 IS 12303:1987 Criteria for design of RCC hinges Apr 2017 C

140 IS 12330:1988 Specification for sulphate resisting Portland Apr 2019 6 S

cement

141 IS 12423:1988 Method for colorimetric analysis of hydraulic Apr 2019 M

cement

142 IS 12600:1989 Portland cement, low heat specification Apr 2019 5 S

143 IS 12803:1989 Methods of analysis of hydraulic cement by X-ray Oct 2018 M

fluorescence spectrometer

144 IS 12813:1989 Method of analysis of hydraulic cement by atomic Oct 2018 M

absorption spectrophotometer

145 IS 12870:1989 Calcined clay pozzolana ― Methods of sampling Feb 2021 M

146 IS 14345:1996 Autoclave apparatus ― Specification Feb 2021 S

147 IS 14687:1999 False work for concrete structures ― Guidelines Apr 2019 C

148 IS 14858:2000 Compression testing machine used for testing of Feb 2021 S
concrete and mortar ― Requirements

149 IS 14959 (Part 1):2001 Determination of water soluble and acid soluble Apr 2016 1 M
chlorides in mortar and concrete ― Method of
test: Part 1 Fresh mortar

150 IS 14959 (Part 2):2001 Determination of water soluble and acid soluble Apr 2016 1 M
chlorides in mortar and concrete ― Method of
test: Part 2 Hardened mortar and concrete

12
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

151 IS 15388:2003 Silica fume ― Specification Apr 2017 1 S

152 IS 16353:2015 Portland cement clinker ― Specification Aug 2020 S

153 IS 16354:2015 Metakaolin for use in cement, cement mortar and Aug 2020 S
concrete ― Specification

154 IS 16415:2015 Composite cement — Specification Dec 2020 S

155 IS 16714:2018 Ground granulated blast furnace slag for use in 1 S

cement, mortar and concrete ― Specification

156 IS 16715:2018 Ultrafine ground granulated blast furnace slag ― 1 S

Specification

157 IS 16993:2018 Microfine ordinary Portland cement ― 1 S

Specification

158 IS 17161:2020 Flexural strength and toughness parameters of M

fibre reinforced concrete ― Method of test

159 SP 23 (S&T):1982 Handbook on concrete mixes (based on Indian 1 O

standards)

160 SP 34 (S&T):1987 Handbook on concrete reinforcement and 1 O

detailing

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 02 (15058) Hardened Concrete — Methods of test: Part 2 Properties of Hardened Concrete
other than strength: Section 3 Oxygen permeability index (first revision of IS 516)

2 DOC:CED 02 (15454) Moulds for Use in Tests of Cement and Concrete — Specification (first revision of
IS 10086)

DRAFTS COMPLETED WIDE CIRCULATION

1 DOC:CED 02 (13804) Amendment No. 6 to IS 456:2000

2 DOC:CED 02 (13883) Amendment No. 2 to IS 1343:2012

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

13
CED 03 SANITARY APPLIANCES AND WATER FITTINGS
SCOPE GLAZED EARTHENWARE AND VITREOUS SANITARY APPLIANCES, INCLUDING WATER
CLOSETS, FLUSHING CISTERNS, BATH TUBS, NON-FERROUS WASTE FITTINGS FOR WASH
BASINS AND SINKS, TRAPS, WASTE PLUGS AND ACCESSORIES FOR WASH BASINS,
MANHOLE COVERS FOR USE IN DRAINAGE WORKS (EXCEPT CONCRETE), TAPS AND
VALVES, BALL VALVES, COPPER AND PLASTIC FLOATS FOR BALL VALVES, CAULKING
LEAD, FERRULES, PLUG COCKS, FOOT VALVES, SURFACE BOXES, STONEWARE PIPES,
WATER METERS, WATER METER BOXES, SLUICE VALVES, AND STAINLESS STEEL AND
PLASTIC WATER TANKS.

LIAISON ISO/PC 316 (P) WATER EFFICIENT PRODUCTS – BANDING

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARD PUBLISHED

1 IS 651:2007 Glazed stoneware pipes and fittings ― Oct 2017 1 S

Specification (sixth revision)

2 IS 771 (Part 1):1979 Specification for glazed fire-clay sanitary Oct 2017 1 S
appliances: Part 1 General requirements
(second revision)

3 IS 771 (Part 2):1985 Specification for glazed fire-clay sanitary Sep 2018 3 S
appliances: Part 2 Specific requirements of
kitchen and laboratory sinks (third revision)

4 IS 771 (Part 3/Sec 1): Specification for glazed fire-clay sanitary Oct 2017 S
1979 appliances: Part 3 Specific requirements of
urinals: Section 1 Slab urinals (second revision)

5 IS 771 (Part 3/Sec 2): Specification for glazed fire-clay sanitary Nov 2020 S
1985 appliances: Part 3 Specific requirements of
urinals: Section 2 Stall urinals (third revision)

6 IS 771 (Part 4):1979 Specification for glazed fire-clay sanitary Oct 2017 S
appliances: Part 4 Specific requirements of post-
mortem slabs (second revision)

7 IS 771 (Part 5):1979 Specification for glazed fire-clay sanitary Oct 2017 S
appliances: Part 5 Specific requirements of
shower trays (second revision)

8 IS 771 (Part 6):1979 Specification for glazed fire-clay sanitary Nov 2020 S
appliances: Part 6 Specific requirements of bed
pan sinks (second revision)

9 IS 771 (Part 7):1981 Specification for glazed fire-clay sanitary Oct 2017 S
appliances: Part 7 Specific requirements of slop
sinks (second revision)

10 IS 772:1973 Specification for general requirements for Oct 2017 1 S

enamelled cast iron sanitary appliances
(second revision)

11 *IS 774:2004 Flushing cistern for water closets and urinals Oct 2019 2 S
(other than plastic cistern) ― Specification
(fifth revision)

14
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

12 IS 778:1984 Specification for copper alloy gate, globe and Nov 2020 4 S
check valves for waterworks purposes
(fourth revision)

13 IS 779:1994 Water meters (domestic type) ― Specification Nov 2020 5 S

(sixth revision)

14 IS 781:1984 Specification for cast copper alloy screw down bib Nov 2020 2 S
taps and stop valves for water services
(third revision)

15 IS 782:1978 Specification for caulking lead (third revision) Oct 2017 S

16 IS 1701:1960 Specification for mixing valves for ablutionary and Oct 2017 S
domestic purposes

17 IS 1703:2000 Water fittings ― copper alloy float valves Nov 2020 1 S

(horizontal plunger type) ― Specification
(fourth revision)

18 IS 1711:1984 Specification for self-closing taps for water supply Nov 2020 S
purposes (second revision)

19 IS 1726:1991 Cast iron manhole covers and frames ― Oct 2017 S

Specification (third revision)

20 IS 1795:1982 Specification for pillar taps for water supply Nov 2020 S
purposes (second revision)

21 IS 2326:1987 Specification for automatic flushing cisterns for Sep 2018 S

urinals (other than plastic cisterns)
(second revision)

22 IS 2373:1981 Specification for water meters (bulk type) Oct 2017 3 S

(third revision)

23 IS 2548 (Part 1):1996 Plastic seats and covers for water-closets ― Mar 2017 1 S
Specification: Part 1 Thermoset seats and covers
(fifth revision)

24 IS 2548 (Part 2):1996 Plastic seats and covers for water-closets ― Mar 2017 2 S
Specification: Part 2 Thermo plastic seats and
covers (fifth revision)

25 *IS 2556 (Part 1):1994 Vitreous sanitary appliances (vitreous china) ― Mar 2017 5 S
Specification: Part 1 General requirements
(third revision)

26 IS 2556 (Part 2):2004 Vitreous sanitary appliances (vitreous china) ― Oct 2019 2 S
Specification: Part 2 Specific requirements of
washdown water closets (fifth revision)

27 IS 2556 (Part 3):2004 Vitreous sanitary appliances (vitreous china) ― Oct 2019 S
Specification: Part 3 Specific requirements of
squatting pans (fifth revision)

28 IS 2556 (Part 4):2004 Vitreous sanitary appliances (vitreous China) ― Oct 2019 3 S
Specification: Part 4 Specific requirements of
wash basins (fourth revision)

15
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

29 IS 2556 (Part 5):1994 Vitreous sanitary appliances (vitreous China) ― Oct 2019 3 S
Specification: Part 5 Specific requirements of
laboratory sinks (third revision)

30 *IS 2556 (Part 6):1995 Vitreous sanitary appliances (vitreous China) ― Sep 2018 2 S
Specification: Part 6 Specific requirements of
urinals and partition plates (fourth revision)

31 IS 2556 (Part 7):1995 Vitreous sanitary appliances (vitreous China) ― Sep 2018 3 S
Specification: Part 7 Specific requirements of
accessories for sanitary appliances (third revision)

32 *IS 2556 (Part 8):2004 Vitreous sanitary appliances (vitreous China) ― Oct 2019 S
Specification: Part 8 Specific requirements of
pedestal close coupled washdown and syphonic
water closets (fifth revision)

33 IS 2556 (Part 9):2004 Vitreous sanitary appliances (vitreous China) ― Oct 2019 S
Specification: Part 9 Specific requirements of
pedestal type bidets (fifth revision)

34 IS 2556 (Part 14):1995 Vitreous sanitary appliances (vitreous China) ― Nov 2020 1 S
Specification: Part 14 Specific requirements of
integrated squatting pans (first revision)

35 IS 2556 (Part 15):2004 Vitreous sanitary appliances (vitreous China) ― Oct 2019 2 S
Specification: Part 15 Specific requirements of
universal water closets (second revision)

36 IS 2556 (Part 16):2002 Vitreous sanitary appliances (vitreous China) ― Oct 2017 S
Specification: Part 16 Specific requirements of
wash down wall mounted water closets

37 IS 2556 (Part 17):2001 Vitreous sanitary appliances (vitreous China) ― Mar 2017 S
Specification: Part 17 Specific requirements of
wall mounted bidets

38 IS 2685:1971 Code of practice for selection, installation and Oct 2017 2 C

maintenance of sluice valves (first revision)

39 IS 2692:1989 Ferrules for water services ― Specification Sep 2018 3 S

(second revision)

40 IS 2963:2013 Copper alloy waste fittings and waste plug for Sep 2018 S
wash basin and sinks ― Specification
(second revision) (amalgamating IS 3311)

41 IS 3004:1979 Specification for plug cocks for water supply Nov 2020 S
purposes (first revision)

42 IS 3006:1979 Specification for chemically resistant glazed Oct 2017 S

stoneware pipes and fittings (first revision)

43 IS 3042:1965 Specification for single faced sluice gates (200 to Sep 2018 S
1200 mm)

44 IS 3950:1979 Specification for surface boxes for sluice valves Oct 2017 1 S
(first revision)

16
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

45 IS 4038:1986 Specification for foot valves for water works Nov 2020 S
purposes (second revision)

46 IS 4346:1982 Specification for washers for use with fittings for Nov 2020 S
water services (first revision)

47 IS 5219:2013 Cast copper alloy traps ― Specification Sep 2018 S

(first revision)

48 IS 5312 (Part 1):2004 Swing check type reflux (non-return) valves for Oct 2019 2 S
water works purposes ― Specification:
Part 1 Single door pattern (second revision)

49 IS 5312 (Part 2):2013 Swing check type reflux (non-return) valves for Sep 2018 S
water works purpose ― Specification: Part 2 Multi-
door pattern

50 IS 5455:1969 Specification for cast iron steps for manholes Oct 2017 S

51 IS 5961:1970 Specification for cast iron gratings for drainage Oct 2017 S
purposes

52 IS 6411:1985 Specification for gel-coated glass fibre reinforced Nov 2020 S

polyester resin bath tubs (first revision)

53 IS 6784:1996 Methods for performance testing of water meters Mar 2017 1 M

(domestic type) (second revision)

54 *IS 7231:1994 Plastic flushing cisterns for water-closets and Oct 2019 6 S
urinals (second revision)

55 *IS 8931:1993 Copper alloy fancy single taps, combination tap Sep 2018 1 S
assembly and stop valves for water services ―
Specification (first revision)

56 IS 9140:1996 Method of sampling of vitreous and fire clay Mar 2017 M

sanitary appliances (second revision)

57 IS 9338:2013 Cast iron/S.G. Iron/Cast Steel screw-down stop Sep 2018 S

valves for water works purposes ― Specification
(second revision)

58 IS 9739:1981 Specification for pressure reducing valves for Oct 2017 3 S

domestic water supply systems

59 IS 9758:1981 Specification for flush valves and fittings for water Oct 2017 2 S
closets and urinals

60 IS 9762:1994 Specification for polyethylene floats (spherical) for Oct 2019 S

float valves (first revision)

61 IS 9763:2000 Plastics bib taps, pillar taps, angle valves and stop Nov 2020 S
valves for hot and cold water services ―
Specification (second revision)

62 IS 11246:1992 Glass fibre reinforced polyester resin (GRP) Oct 2017 1 S

squatting pans ― Specification (first revision)

17
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

63 *IS 12234:1988 Specification for plastic equilibrium float valves for Sep 2018 S
cold water services

64 IS 12701:1996 Rotational moulded polyethylene water storage Mar 2017 2 S

tanks ― Specification (first revision)

65 IS 13049:1991 Diaphragm type (plastic body) float operated Oct 2017 2 S

valves for cold water services ― Specification

66 IS 13114:1991 Forged brass gate, globe and check valves for Oct 2017 S
water works purposes ― Specification

67 IS 13349:1992 Cast iron single faced thimble mounted sluice Oct 2017 1 S
gates ― Specification

68 IS 13983:1994 Stainless steel sinks for domestic purposes ― Oct 2019 3 S

Specification

69 IS 14399 (Parts 1 & 2): Hot press moulded thermosetting glass fibre Mar 2017 1 S
1996 reinforced polyester resin (GRP) sectional water
storage tanks: Part 1 Specification for panels
Part 2 Guidelines for assembly, installation and
testing

70 IS 14845:2000 Resilient seated cast iron air relief valves for water Nov 2020 1 S
works purposes ― Specification

71 IS 14846:2000 Sluice valves for water works purposes (50 to Nov 2020 4 S
1200 mm size) ― Specification

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 03 (14857) Draft Indian Standard Water efficient plumbing products — Requirements:
Part 1 Sanitaryware

2 DOC:CED 03 (14859) Draft Indian Standard Water efficient plumbing products — Requirements:
Part 2 Sanitary fittings

3 DOC:CED 03 (16386) Draft Indian Standard Beta (outflow) valves for gravity type flushing cisterns —
Specification

4 DOC:CED 03 (16394) Draft Indian Standard Plastic flushing cisterns for water closets and urinals —
Specification (third revision of IS 7231)

5 DOC:CED 03 (16479) Draft Indian Standard Ceramic (vitreous China) flushing cisterns for water closets
and urinals — Specification (sixth revision of IS 774)

6 DOC:CED 03 (16486) Draft Indian Standard Plastic equilibrium float valves for cold water services —
Specification (first revision of IS 12234)

7 DOC:CED 03 (16491) Amendment No. 3 to IS 2556 (Part 2):2004

8 DOC:CED 03 (16524) Amendment No. 3 to IS 2548 (Part 2):1996

18
9 DOC:CED 03 (16578) Draft Indian Standard Vitreous China sanitary appliances — Specification:
Part 1 General requirements [fourth revision of IS 2556 (Part 1)]

10 DOC:CED 03 (16779) Draft Indian Standard Vitreous China Sanitary Appliances — Specification:
Part 6 Specific Requirements of Urinal and Partition Plates [fifth revision of IS 2556
(Part 6)]

11 DOC:CED 03 (16892) Draft Indian Standard Vitreous China sanitary appliances — Specification:
Part 8 Specific requirements of close-coupled and one-piece, pedestal wash-down
and syphonic water closets [sixth revision of IS 2556 (Part 8)]

12 DOC:CED 03 (16985) Draft Indian Standard Copper alloy single taps, stop valves, combination tap
assembly and single lever mixers for water services — Specification
(second revision of IS 8931)

13 DOC:CED 03 (17161) Amendment No. 2 to IS 651:2007

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

19
CED 04 BUILDING LIME AND GYPSUM PRODUCTS
SCOPE SUBJECTS PERTAINING TO:
1) MANUFACTURE OF BUILDING LIME AND LIME PRODUCTS
2) SUPPLY AND STORAGE OF BUILDING LIME
3) USE OF BUILDING LIME AND LIME PRODUCTS ON CONSTRUCTION WORKS
4) GYPSUM BUILDING MATERIAL
5) GYPSUM PLASTER BOARD, NON-LOAD BEARING GYPSUM PLASTER BLOCK
6) GLOSSARY OF TERMS RELATING TO LIME AND GYPSUM
7) GYPSUM PLASTER
8) METHOD OF TEST FOR GYPSUM PLASTER CONCRETE AND PRODUCTS,GYPSUM
TILES AND REINFORCED BLOCKS

LIAISON ISO/TC 74 (P) CEMENT AND LIME

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 712:1984 Specification for building limes (third revision) May 2019 1 S

2 IS 1624:1986 Methods of field testing of building lime May 2019 2 M

(second revision)

3 IS 1635:1992 Field slaking of building lime and preparation of Jan 2019 C

putty ― Code of practice (second revision)

4 IS 1849 (Part 1/Sec1): Design and installation of vertical mixed feed lime Jan 2019 C
1990 kiln ― Guide: Part 1 For limestone:
Section 1 Masonry type shaft (second revision)

5 IS 1849 (Part 1/Sec 2): Design and installation of vertical mixed feed lime May 2019 1 C
1991 kiln ― Guide: Part 1 For limestone:
Section 2 Reinforced cement concrete type shaft

6 IS 1861 (Part 1):1990 Manufacture of lime in vertical mixed-feed type May 2019 C
kilns ― Guide: Part 1 From limestone
(second revision)

7 *IS 2095 (Part 1):2011 Gypsum plaster boards ― Specification: Mar 2021 S
Part 1 Plain gypsum plaster boards (third revision)

8 *IS 2095 (Part 2):2001 Gypsum plaster boards ― Specification: Jan 2017 2 S
Part 2 Coated/ laminated gypsum plaster boards
(second revision)

9 *IS 2095 (Part 3):2018 Gypsum plaster boards — Specification: S

Part 3 Reinforced gypsum plaster boards, tiles,
cornices and mouldings (third revision)

10 IS 2469:1976 Glossary of terms relating to gypsum Jan 2017 T

(first revision)

11 IS 2541:1991 Preparation and use of lime concrete ― Code of May 2019 3 C

practice (second revision)

20
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

12 IS 2542 (Part 1/Sec 1 to Methods of test for gypsum plaster, concrete and Jan 2017 1 M
12):1978 products: Part 1 Plaster and concrete
(first revision)
Section 1 Normal consistency of gypsum plaster
Section 2 Normal consistency of gypsum
concrete
Section 3 Setting time of plaster and concrete
Section 4 Transverse strength of gypsum plaster
Section 5 Compressive strength and dry set
density of gypsum plaster
Section 6 Soundness of gypsum plaster
Section 7 Mechanical resistance of gypsum
plaster by dropping ball test
Section 8 Freedom from coarse particles
Section 9 Expansion of plaster
Section 10 Sand in set plaster
Section 11 Wood fibre content in wood fibre
gypsum plaster
Section 12 Dry bulk density

13 IS 2542 (Part 2/Sec 1 to Methods of test for gypsum plaster, concrete and Jan 2017 M
8):1981 products: Part 2 Gypsum products (first revision)
Section 1 Measurement of dimensions
Section 2 Determination of mass
Section 3 Determination of mass and thickness of
paper surfacing
Section 4 Transverse strength
Section 5 Compressive strength
Section 6 Water absorption
Section 7 Moisture content
Section 8 Nail retention of precast reinforced
gypsum slabs

14 IS 2547 (Part 1):1976 Specification for gypsum building plaster: Jan 2017 3 S
Part 1 Excluding premixed lightweight plasters
(first revision)

15 IS 2547 (Part 2):1976 Specification for gypsum building plasters: Jan 2017 1 S
Part 2 Premixed lightweight plasters (first revision)

16 IS 2686:1977 Specification for cinder aggregates for use in lime Jan 2019 1 S
concrete (first revision)

17 IS 2849:1983 Specification for non-load bearing gypsum partition Jan 2017 4 S

blocks (solid and hollow types)
(first revision)

18 IS 3068:1986 Specification for broken brick (burnt clay) coarse May 2019 1 S
aggregate for use in lime concrete
(second revision)

19 IS 3115:1992 Lime based blocks ― Specification Jan 2019 1 S

(second revision)

20 IS 3182:1986 Specification for broken brick (burnt clay) fine May 2019 1 S
aggregate for use in lime mortar
(second revision)

21
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

21 IS 4098:1983 Specification for lime-pozzolana mixture May 2019 3 S

(first revision)

22 IS 4139:1989 Calcium silicate bricks ― Specification May 2019 1 S

(second revision)

23 IS 5817:1992 Preparation and use of lime-pozzolana mixture May 2019 2 C

concrete in buildings and roads ― Code of
practice (first revision)

24 IS 6508:1988 Glossary of terms relating to building lime Jan 2019 T

(first revision)

25 IS 6932 (Part 1):1973 Methods of tests for building limes: May 2019 3 M
Part 1 Determination of insoluble residue, loss on
ignition, insoluble matter, silicone dioxide, ferric
and aluminium oxide, calcium oxide and
magnesium oxide

26 IS 6932 (Part 2):1973 Methods of tests for building limes: May 2019 2 M
Part 2 Determination of carbon dioxide content

27 IS 6932 (Part 3):1973 Methods of tests for building limes: May 2019 1 M
Part 3 Determination of residue on slaking of
quicklime

28 IS 6932 (Part 4):1973 Methods of tests for building limes: May 2019 2 M
Part 4 Determination of fineness of hydrated lime

29 IS 6932 (Part 5):1973 Methods of tests for building limes: May 2019 1 M
Part 5 Determination of unhydrated oxide

30 IS 6932 (Part 6):1973 Methods of tests for building limes: May 2019 1 M
Part 6 Determination of volume yield of quicklime

31 IS 6932 (Part 7):1973 Methods of tests for building limes: May 2019 4 M
Part 7 Determination of compressive and
transverse strength

32 IS 6932 (Part 8):1973 Methods of tests for building limes: May 2019 1 M
Part 8 Determination of workability

33 IS 6932 (Part 9):1973 Methods of tests for building limes: May 2019 1 M
Part 9 Determination of soundness

34 IS 6932 (Part 10):1973 Methods of tests for building limes: May 2019 1 M
Part 10 Determination of popping and pitting of
hydrated lime

35 IS 6932 (Part 11):1983 Methods of tests for building limes: May 2019 1 M
Part 11 Determination of setting time of hydrated
lime

36 IS 8272:1984 Specification for gypsum plaster for use in the Jan 2017 1 S
manufacture of fibrous plaster boards
(first revision)

37 IS 9498:1980 Specification for inorganic aggregates for use in Jan 2017 1 S

gypsum plaster

22
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

38 IS 10049:1981 Code of practice for manufacture of lime based Jan 2019 3 C

blocks

39 IS 10359:1982 Code of practice for manufacture and use of lime- May 2019 4 C
pozzolana concrete blocks for paving

40 IS 10360:1982 Specification for lime-pozzolana concrete blocks May 2019 4 S

for paving

41 IS 10772:1983 Specification for quick setting lime pozzolana May 2019 3 S

mixture

42 IS 12654:1989 Low grade gypsum ― Use in building industry ― Sep 2020 1 C

Code of practice

43 *IS 12679:1989 By-product gypsum for use in plaster, blocks and Sep 2020 S
boards ― Specification

44 IS 12894:2002 Pulverized fuel ash-lime bricks ― Specification Jan 2017 2 S

(first revision)

45 IS 13001:1991 Guidelines for manufacture of gypsum plaster in Jan 2017 C

mechanized pan system

46 IS 14401:1996 Handling and storage of building limes ― Jan 2017 1 C

Guidelines

47 IS 14860:2000 Guidelines on fuel saving in vertical mixed-feed May 2019 C

lime shaft kilns

48 IS 15648:2006 Pulverized fuel ash for lime-pozzolana mixture Sep 2020 S

applications ― Specification

49 IS 16135:2014 Dry lining and partitioning using gypsum May 2019 C

plasterboards ― Code of practice

50 IS 17400:2021 Glass fibre reinforced gypsum panels ― S

Specification

51 IS 17401:2001 Design and construction of buildings using glass C

fibre reinforced gypsum panels ― Code of practice

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 04 (14874) Draft Indian Standard for by-product gypsum for use in plaster, blocks and boards
— Specification (first revision of IS 12679)

2 DOC:CED 04 (15423) Gypsum Plaster Boards — Specification: Part 1 Plain Gypsum Plaster Boards
[fourth revision of IS 2095 (Part 1)]

3 DOC:CED 04 (15426) Gypsum Plaster Boards — Specification: Part 2 Coated/ Laminated Gypsum
Plaster Boards [third revision of IS 2095 (Part 2)]

23
4 DOC:CED 04 (15427) Gypsum Plaster Boards – Specification: Part 3 Reinforced Gypsum Plaster Boards,
Tiles, Cornices and Mouldings [third revision of IS 2095 (Part 3)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

24
CED 05 FLOORING, WALL FINISHING AND ROOFING
SCOPE STANDARDIZATION IN THE FIELD OF FLOORING MADE OF MATERIALS SUCH AS
CONCRETE, CONCRETE TILES, MAGNESIUM OXYCHLORIDE, LINOLEUM, RUBBER, BITUMEN
MASTIC AND PLASTICS; ACID AND ALKALI RESISTING FLOORING INCLUDING ACID
RESISTING PLASTERS, WALL FINISHING, BITUMEN IMPREGNATED ROOFING SHEETS,
PLASTICS BASED ROOFING SHEETS ETC, (EXCLUDING METAL AND ASBESTOS CEMENT
SHEETS) AND THE RELATED CODES OF PRACTICES

LIAISON ISO/TC 189 (P) CERAMIC TILES

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

1 IS 653:1992 Linoleum sheets and tiles ― Specification Jan 2017 1 S

(third revision)

2 IS 657:1982 Specification for materials for use in the Jan 2017 S

manufacture of magnesium oxychloride flooring
compositions (second revision)

3 IS 658:1982 Code of practice for magnesium oxychloride Jan 2017 C

composition floors (second revision)

4 IS 809:1992 Rubber flooring materials for general purposes ― Jan 2017 S

Specification (first revision)

5 IS 1195:2002 Bitumen-mastic for flooring ― Specification Nov 2017 S

(third revision)

6 IS 1196:1978 Code of practice for laying bitumen mastic flooring Jan 2017 C
(second revision)

7 IS 1197:1970 Code of practice for laying of rubber floors Jan 2017 C

(first revision)

8 IS 1198:1982 Code of practice for laying, fixing and maintenance Jan 2017 C
of linoleum floors (first revision)

9 IS 1237:2012 Cement concrete flooring tiles ― Specification Jan 2017 1 S

(second revision)

10 IS 1443:2018 Laying and finishing of cement concrete tiles ― C

Code of practice (second revision)

11 IS 1542:1992 Sand for plaster ― Specification (second revision) Feb 2019 S

12 IS 1630:1984 Specification for mason's tools for plaster work and Jan 2017 S
pointing work (first revision)

13 IS 1661:1972 Code of practice for application of cement and Jan 2017 C

cement-lime plaster finishes (first revision)

14 IS 2114:2018 Laying in-situ terrazzo floor finish ― Code of C

practice (second revision)

15 IS 2394:1984 Code of practice for application of lime plaster Jan 2017 C

finish (first revision)

25
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

16 IS 2402:1963 Code of practice for external rendered finishes Jan 2017 C

17 IS 2571:1970 Code of practice for laying in-situ cement concrete Jan 2017 C
flooring (first revision)

18 IS 3461:1980 Specification for PVC asbestos floor tiles Jan 2017 4 S

(first revision)

19 IS 3462:1986 Specification for unbacked flexible PVC flooring Jan 2017 1 S

(second revision)

20 IS 3464:1986 Methods of test for plastic flooring and wall tiles Jan 2017 2 M
(second revision)

21 IS 4441:1980 Code of practice for use of silicate type chemical Jan 2017 1 M
resistant mortars (first revision)

22 IS 4442:1980 Code of practice for use of sulphur type chemical Jan 2017 C
resistant mortars (first revision)

23 IS 4443:1980 Code of practice for use of resin type chemical Jan 2017 1 C
resistant mortars (first revision)

24 IS 4456 (Part 1):1967 Methods of test for chemical resistant mortars: Jan 2017 1 M
Part 1 Silicate type and resin type

25 IS 4456 (Part 2):1967 Methods of test for chemical resistant mortars: Jan 2017 M
Part 2 Sulphur type

26 IS 4457:2007 Ceramic unglazed vitreous acid resisting tiles ― Jun 2017 S

Specification (second revision)

27 IS 4631:1986 Code of practice for laying of epoxy resin floor Jan 2017 C
toppings (first revision)

28 IS 4832 (Part 1):1969 Specification for chemical resistant mortars: Jan 2017 1 S
Part 1 Silicate type

29 IS 4832 (Part 2):1969 Specification for chemical resistant mortars: Jan 2017 1 S
Part 2 Resin type

30 IS 4832 (Part 3):1968 Specification for chemical resistant mortars: Jan 2017 1 S
Part 3 Sulphur type

31 IS 4860:1968 Specification for acid-resistant bricks Jan 2017 S

32 IS 4971:2007 Recommendations for selection of industrial floor Jun 2017 O

finishes (first revision)

33 IS 5317:2002 Pitch-mastic for bridge decking and roads ― Nov 2017 S

Specification (second revision)

34 IS 5318:1969 Code of practice for laying of flexible PVC sheet Jan 2017 C
and tile flooring

35 IS 5491:1969 Code of practice for laying of in-situ granolithic Jan 2017 C

concrete floor topping

26
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

36 IS 5766:1970 Code of practice for laying burnt clay brick flooring Jan 2017 C

37 IS 6278:1971 Code of practice for whitewashing and colour- Jan 2017 C

washing

38 IS 7956:1975 Recommendations for selection of dairy floor Jan 2017 O

finishes

39 IS 8374:1977 Specification for bitumen mastic, anti-static and Jan 2017 S

electrically conducting grade

40 IS 9162:1979 Methods of tests for epoxy resins, hardeners and Jan 2017 M
epoxy resin compositions for floor topping

41 IS 9197:1979 Specification for epoxy resin, hardeners and epoxy Jan 2017 S
resin compositions for floor topping

42 IS 9510:1980 Specification for bitumen mastic, acid-resisting Jan 2017 S

grade

43 IS 9704:1980 Methods of tests for linoleum sheets and tiles Jan 2017 2 M

44 IS 10132:1982 Method of test for materials for use in the Jan 2017 M
preparation of magnesium oxychloride flooring
compositions

45 IS 10403:1983 Glossary of terms relating to building finishes Jan 2017 T

46 IS 12583:1988 Specification for corrugated bitumen roofing sheets Feb 2019 2 S

47 IS 12866:2021 Plastic translucent sheets made from thermo- S

setting polyester resin (glassfibre reinforced) ―
Specification (first revision)

48 IS 13026:1991 Bitumen mastic for flooring for industries handling Jan 2017 1 S
LPG and other light hydrocarbon products ―
Specification

49 IS 13074:1991 Laying of bitumen mastic flooring for industries Jan 2017 C

handling LPG and other light hydrocarbon products
― Code of practice

50 IS13630 (Parts 1):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 1 Determination of
dimensions and surface quality (second revision)

51 IS13630 (Part 2):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 2 Determination of water
absorption and bulk density (second revision)

52 IS13630 (Part 3):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 3 Determination of
moisture expansion using boiling water
(second revision)

53 IS13630 (Part 4):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 4 Determination of linear
thermal expansion (second revision)

27
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

54 IS13630 (Part 5):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 5 Determination of
resistance to thermal shock (second revision)

55 IS13630 (Part 6):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 6 Determination of
modulus of rupture and breaking strength
(second revision)

56 IS13630 (Part 7):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 7 Determination of
chemical resistance unglazed tiles
(second revision)

57 IS13630 (Part 8):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 8 Determination of
chemical resistance glazed tiles (second revision)

58 IS13630 (Part 9):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 9 Determination of
crazing resistance - glazed tiles (second revision)

59 IS13630 (Part 10):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 10 Determination of
frost resistance (second revision)

60 IS13630 (Part 11):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 11 Determination of
resistance of surface abrasion - Glazed tiles
(second revision)

61 IS13630 (Part 12):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 12 Determination of
resistance to deep abrasion - Unglazed tiles
(second revision)

62 IS13630 (Part 13):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 13 Determination of
scratch hardness of surface according to MOHS
(second revision)

63 IS13630 (Part 14):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 14 Determination of
impact resistance by measurement of coefficient of
restitution (first revision)

64 IS13630 (Part 15):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 15 Ceramic tiles
sampling and basis for acceptance (first revision)

65 IS13630 (Part 16):2019 Ceramic tiles ― Methods of Test, sampling and M

basis for acceptance: Part 16 Determination of
Lead and Cadmium Given Off by Glazed Tiles

66 IS 13712:2019 Ceramic tiles ― Definitions, classifications, S

characteristics and marking (second revision)

28
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

67 IS 13801:2013 Chequered cement concrete tiles ― Specification May 2018 S

(first revision)

68 IS 15193:2002 Laying of pitch-mastic flooring for industries Nov 2017 C

handling heavy hydrocarbon products like
kerosene, diesel and furnace oil ― Code of
practice

69 IS 15194:2002 Pitch-mastic flooring for industries handling heavy Nov 2017 O

hydrocarbon products like kerosene, diesel and
furnace oil ― Specification

70 IS 15224:2002 Laying of plastic translucent sheets made from Nov 2017 C

thermosetting polyester resin (glass fibre
reinforced) alone or in conjunction with asbestos
cement sheets/steel sheets/aluminium sheets ―
Code of practice

71 IS 15401:2003 Wall coverings in roll form ― Vocabulary and Feb 2019 T

symbols

72 IS 15418:2003 Wall coverings in roll form for finished wall papers, Feb 2019 S
wall vinyls and plastic wall coverings ―
Specification

73 IS 15477:2019 Adhesives for use with ceramic, mosaic and stone S

tiles ― Specification (first revision)

74 IS 15622:2017 Pressed ceramic tiles ― Specification 1 S

(first revision)

75 IS 15658:2021 Concrete blocks for paving ― Specification (first S

revision)

76 IS 16777:2019 Laying of paver blocks ― Code of practice C

77 IS 17190:2020 Grouts for filling of joints of tiles and stones ― S

Specification

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 05 (15898) Aluminium composite panel ― Specification

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

29
CED 06 STONES
SCOPE STANDARDIZATION IN THE FIELD OF STONES FOR CONSTRUCTION

LIAISON ISO/TC 327 (P) NATURAL STONES

ISO/TC 328 (P) ENGINEERED STONES

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1121 (Part 1):2013 Determination of strength properties of natural Dec 2017 M

building stones ― Methods of test:
Part 1 Compressive strength (second revision)

2 IS 1121 (Part 2):2013 Determination of strength properties of natural Dec 2017 M

building stones ― Methods of test:
Part 2 Transverse strength (second revision)

3 IS 1121 (Part 3):2012 Determination of strength properties of natural Dec 2017 M

building stones ― Methods of test:
Part 3 Tensile strength (second revision)

4 IS 1121 (Part 4):2013 Determination of strength properties of natural Dec 2017 M

building stones ― Methods of test:
Part 4 Shear strength (second revision)

5 IS 1122:1974 Method of test for determination of true specific Dec 2017 M

gravity of natural building stones (first revision)

6 IS 1123:1975 Method of identification of natural building Dec 2017 M

stones (first revision)

7 IS 1124:1974 Method of test for determination of water Dec 2017 M

absorption, apparent specific gravity and
porosity of natural building stones (first revision)

8 IS 1125:2013 Determination of weathering of natural building Sep 2018 M

stones ― Methods of test (second revision)

9 IS 1126:2013 Determination of durability of natural building Aug 2018 M

stones ― Methods of test (second revision)

10 IS 1127:1970 Recommendations for dimensions and Dec 2017 O

workmanship of natural building stones for
masonry work (first revision)

11 IS 1128:1974 Specification for limestone (slab and tiles) Dec 2017 S

(first revision)

12 IS 1129:1972 Recommendation of dressing of natural building Dec 2017 O

stones (first revision)

13 IS 1130:1969 Specification for marble (blocks, slabs and tiles) Dec 2017 S

14 IS 1706:1972 Method for determination of resistance to wear Dec 2017 M

by abrasion of natural building stones
(first revision)

30
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

15 IS 1805:1973 Glossary of terms relating to stones, quarrying Dec 2017 T

and dressing (first revision)

16 IS 3316:1974 Specification for structural granite (first revision) Dec 2017 S

17 IS 3620:1979 Specification for laterite stone block for masonry Dec 2017 S
(first revision)

18 IS 3622:1977 Specification for sandstone (slabs and tiles) Dec 2017 S

(first revision)

19 IS 4121:1967 Method of test for determination of water Dec 2017 M

transmission rate by capillary action through
natural building stones

20 IS 4122:1967 Method of test for surface softening of natural Dec 2017 M

building stones by exposure to acidic
atmospheres

21 IS 4348:1973 Methods of test for determination of permeability Dec 2017 M

of natural building stones (first revision)

22 IS 5218:1969 Method of test for toughness of natural building Dec 2017 M

stones

23 IS 5640:1970 Method of test for determining aggregates Dec 2017 1 M

impact value of soft coarse aggregates

24 IS 6241:1971 Method of test for determination of stripping Dec 2017 M

value of road aggregates

25 IS 6250:1981 Specification for roofing slate tiles (first revision) Dec 2017 S

26 IS 6579:1981 Specification for coarse aggregate for water Dec 2017 S

bound macadam (first revision)

27 IS 7779 (Part 1/Sec 1): Schedule for properties and availability of stones Dec 2017 O
1975 for construction purposes: Part 1 Gujarat state:
Section 1 Availability of Stones

28 IS 7779 (Part 1/Sec 2): Schedule for properties and availability of stones Dec 2017 O
1975 for construction purposes: Part 1 Gujarat state:
Section 2 Engineering properties of building
stones

29 IS 7779 (Part 1/Sec 3): Schedule for properties and availability of stones Dec 2017 O
1975 for construction purposes: Part 1 Gujarat state:
Section 3 Engineering properties of stone
aggregates

30 IS 7779 (Part 2/Sec 1): Schedule for properties and availability of stones Dec 2017 O
1979 for construction purposes: Part 2 Maharashtra
state: Section 1 Availability of stones

31 IS 7779 (Part 2/Sec 2): Schedule of properties and availability of stones Dec 2017 O
1979 for construction purposes: Part 2 Maharashtra
state: Section 2 Engineering properties of
building stones

31
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

32 IS 7779 (Part 2/Sec 3): Schedule for properties and availability of stones Dec 2017 O
1979 for construction purposes: Part 2 Maharashtra
state: Section 3 Engineering properties of stone
aggregates

33 IS 7779 (Part 3/Sec 2): Schedule for properties and availability of stones Dec 2017 O
1980 for construction purposes: Part 3 Tamil Nadu
state: Section 2 Engineering properties of
building stones

34 IS 7779 (Part 3/Sec 3): Schedule for properties and availability of stones Dec 2017 O
1980 for construction purposes: Part 3 Tamil Nadu
state: Section 3 Engineering properties of stone
aggregates

35 IS 7779 (Part 4/Sec 1 to Schedule for properties and availability of stones Dec 2017 O
3):1996 for construction purposes: Part 4 Karnataka
state:
Section 1 Availability of stones
Section 2 Engineering properties of building
stones
Section 3 Engineering properties of stones
aggregates

36 IS 7779 (Part 5/Sec 1 to Schedule for properties and availability of stones Jan 2017 O
3):1997 for construction purposes: Part 5 Andhra
Pradesh:
Section 1 Availability of stones
Section 2 Engineering properties of building
stones
Section 3 Engineering properties of stones
aggregates

37 IS 8348:1977 Code of practice for stacking and packing of Dec 2017 C

stone slabs for transportation

38 IS 8381:1977 Recommended practice for quarrying stones for Dec 2017 O

construction purposes

39 IS 8759:1977 Code of practice for maintenance and Dec 2017 C

preservation of stones in buildings

40 IS 9394:1979 Specification for stone lintels Dec 2017 S

41 IS 14223 (Part 1):1995 Polished building stones ― Specification: Jan 2017 S

Part 1 Granite

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

32
CED 07 STRUCTURAL ENGINEERING AND STRUCTURAL SECTIONS
SCOPE STANDARDIZATION IN THE FIELD OF STRUCTURAL ENGINEERING USING STEEL/ALUMINIUM
STRUCTURAL SECTIONS INCLUDING PIPELINES FOR GAS AND FORMULATION OF INDIAN
STANDARDS ON DIMENSIONS/TOLERANCES OF VARIOUS HOT ROLLED/COLD FORMED
SECTIONS, BARS AND FLAT PRODUCTS IN STEEL AND ALUMINIUM FOR STRUCTURAL AND
GENERAL ENGINEERING APPLICATIONS

LIAISION ISO/TC 17/SC 3 (P) STEELS FOR STRUCTURE PURPOSES

ISO/TC 167 (O) STEEL AND ALUMINIUM STRUCTURES
ISO/TC 167/SC 1 (O) STEEL MATERIAL AND DESIGN (STANDBY)
ISO/TC 167/SC 3 (O) ALUMINIUM STRUCTURES (STANDBY)

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 800:2007 General construction in steel ― Code of practice Dec 2017 1 C

(third revision)

2 IS 801:1975 Code of practice for use of cold-formed light gauge Jan 2021 1 C
steel structural members in general building
construction (first revision)

3 IS 802 (Part 1/Sec 1): Use of structural steel in overhead transmission Aug 2020 C
2015 line towers ― Code of practice: Part 1 Materials,
Loads and design strengths: Section 1 Materials
and Loads (fourth revision)

4 IS 802 (Part 1/Sec 2): Use of structural steel in overhead transmission C

2016 line towers ― Code of practice: Part 1 Material,
loads and design strengths: Section 2 Design
strengths (third revision)

5 IS 802 (Part 2):1978 Code of practice for use of structural steel in Dec 2017 1 C
overhead transmission line towers:
Part 2 Fabrication, galvanizing: inspection and
packing

6 IS 802 (Part 3):1978 Code of practice for use of structural steel in Dec 2017 C
overhead transmission line towers: Part 3 Testing

7 IS 803:1976 Code of practice for design, fabrication and Dec 2017 1 C

erection of vertical mild steel cylindrical welded oil
storage tanks (first revision)

8 IS 804:1967 Specification for rectangular pressed steel tanks Dec 2017 2 S

(first revision)

9 IS 805:1968 Code of practice for use of steel in gravity water Dec 2017 C
tanks

10 IS 806:1968 Code of practice for use of steel tubes in general Dec 2017 1 C
building construction (first revision)

11 *IS 808:1989 Dimensions for hot rolled steel beam, column, Oct 2019 2 D
channel and angle sections (third revision)

33
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

12 IS 811:1987 Specification for cold formed light gauge structural Oct 2019 1 S
steel sections (second revision)

13 IS 1173:1978 Specification for hot rolled slit steel tee bars Oct 2019 S
(second revision)

14 IS 1252:1991 Hot rolled steel bulb angles ― Dimensions Dec 2017 D

(first revision)

15 IS 1730:1989 Steel plates, sheets, strips and flats for structural Oct 2019 D
and general engineering purposes ― Dimensions
(second revision)

16 IS 1732:1989 Steel bars, round and square for structural and Oct 2019 D
general engineering purposes ― Dimensions
(second revision)

17 IS 1863:1979 Specification for rolled steel bulb flats Oct 2019 S

(first revision)

18 IS 1864:1979 Specification for hot rolled steel 'L' sections for Oct 2019 S
shipbuilding (first revision)

19 IS 2314:1986 Specification for steel sheet piling sections Dec 2017 1 S

(first revision)

20 IS 2713 (Parts 1 to 3): Specification for tubular steel poles for overhead Dec 2017 2 S
1980 power lines (second revision)
Part 1 General requirements
Part 2 Special requirements for poles made from
steel of tensile strength 410 MPa
Part 3 Special requirements for poles made from
steel of tensile strength 540 MPa

21 IS 2750:1964 Specification for steel scaffoldings Jan 2021 3 S

22 IS 3443:1980 Specification for crane rail sections (first revision) Oct 2019 1 S

23 IS 3908:1986 Specification for aluminium equal leg angles Dec 2017 S

(first revision)

24 IS 3909:1986 Specification for aluminium unequal leg angles Dec 2017 S

(first revision)

25 IS 3921:1985 Specification for aluminium channels Jan 2021 S

(first revision)

26 IS 3954:1991 Hot-rolled steel channel sections for general Jan 2021 O

engineering purposes ― Dimensions
(first revision)

27 IS 3964:1980 Specification for light rails (first revision) Jan 2021 1 S

28 IS 4000:1992 High strength bolts in steel structures ― Code of Dec 2017 1 C

practice (first revision)

29 IS 4014 (Part 1):1967 Code of practice for steel tubular scaffolding: Jan 2021 C
Part 1 Definitions and materials

34
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

30 IS 5384:1985 Specification for aluminium I-beam (first revision) Jan 2021 S

31 IS 5488:1987 Dimensions and dimensional tolerances for hot- Oct 2019 D

rolled steel plates for ship's hull structure
(first revision)

32 IS 6445:1985 Specification for aluminium tee-sections Jan 2021 S

(first revision)

33 IS 6449:1987 Specification for aluminium bulb angles for marine Oct 2019 S
application (first revision)

34 IS 6475:1987 Specification for aluminium tee bars for marine Oct 2019 S
application (first revision)

35 IS 6476:1987 Specification for aluminium bulb plates for marine Oct 2019 S
application (first revision)

36 IS 6533 (Part 1):1989 Design and construction of steel chimney ― Code Jan 2021 1 C
of practice: Part 1 Mechanical aspect
(first revision)

37 IS 6533 (Part 2):1989 Design and construction of steel chimney ― Code Dec 2017 1 C
of practice: Part 2 Structural aspect
(first revision)

38 IS 7205:1974 Safety code for erection of structural steel work Jan 2021 SS

39 IS 7215:1974 Tolerances for fabrication of steel structures Jan 2021 1 O

40 IS 7452:1990 Hot rolled steel sections for doors, windows and Dec 2017 S
ventilators ― Specification (second revision)

41 IS 8081:1976 Specification for slotted sections Jan 2021 1 S

42 IS 8147:1976 Code of practice for use of aluminium alloys in Jan 2021 C

structures

43 IS 8640:1977 Recommendations for dimensional parameters for Jan 2021 O

industrial building

44 IS 9178 (Part 1):1979 Criteria for design of steel bins for storage of bulk Jan 2021 2 O
materials: Part 1 General requirements and
assessment of loads

45 IS 9178 (Part 2):1979 Criteria for design of steel bins for storage of bulk Jan 2021 O
materials: Part 2 Design criteria

46 IS 9178 (Part 3):1980 Criteria for design of steel bins for storage of bulk Jan 2021 1 O
materials: Part 3 Bins designed for mass flow and
funnel flow

47 IS 9964 (Part 1):1981 Recommendations for maintenance and operation Jan 2021 O
of petroleum storage tanks: Part 1 Preparation of
tanks for safe entry and work

48 IS 9964 (Part 2):1981 Recommendations for maintenance and operation Jan 2021 O
of petroleum storage tanks: Part 2 Inspection

35
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

49 IS 10182 (Part 1):1982 Dimensions and tolerances for hot-rolled track Jan 2021 D
shoe sections: Part 1 Section TS-L1

50 IS 10182 (Part 2):1985 Dimensions and tolerances for hot-rolled track Jan 2021 D
shoe sections: Part 2 Section TS-H1

51 IS 10987:1992 Code of practice for design, fabrication, testing Dec 2017 C

and installation of under-ground/above-ground
horizontal cylindrical steel storage tanks for
petroleum products (first revision)

52 *IS 12778:2004 Hot rolled parallel flange steel sections for beam, Oct 2019 O
columns and bearing pile ― Dimensions and
section properties (first revision)

53 IS 12779:1989 Rolling and cutting tolerances for hot rolled parallel Oct 2019 O
flange beam and column sections ― Specification

54 IS 12843:1989 Tolerances for erection of steel structures Jan 2021 O

55 IS 15663 (Part 1):2006 Design and installation of natural gas pipelines ― Jul 2016 C
Code of practice: Part 1 Laying of pipelines

56 IS 15663 (Part 2):2006 Design and installation of natural gas pipelines ― Jul 2016 C
Code of practice: Part 2 Laying of pipelines in
crossings

57 IS 15663 (Part 3):2006 Design and installation of natural gas pipelines ― Jul 2016 C
Code of practice: Part 3 Pre-commissioning and
commissioning of pipelines

58 SP 6 (Part 4):1969 Handbook for structural engineers: Part 4 Use of O

high strength friction grip bolts

59 SP 6 (Part 5):1980 Handbook for structural engineers: Part 5 Cold- 1 O

formed, light gauge steel structures (first revision)

60 SP 6 (Part 6):1972 Handbook for structural engineers: O

Part 6 Application of plastic theory in design of
steel structures

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 07 (14899) Draft Indian Standard Hot rolled steel beam, column, channel and angle sections ―
Dimensions and section properties (first revision of IS 808) (amalgamating
IS 12778)
2 DOC:CED 07 (15603) Draft Indian Standard Use of structural steel in overhead transmission line towers
― Code of practice: Part 6 Tower erection [IS 802 (Part 6)]

3 DOC:CED 07 (16865) Draft Indian Standard Isolated Towers, Masts and Poles Using Structural Steel ―
Code of Practice

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

36
CED 09 TIMBER AND TIMBER STORES
SCOPE TIMBERS; STANDARD NAMES OF INDIAN TIMBERS; CLASSIFICATION OF COMMERCIAL
TIMBERS AND THEIR ZONAL DISTRIBUTION; CHARACTERISTICS OF IMPORTED AND
PLANTATION TIMBERS; TIMBER, SIZING DEFECTS OF; TIMBER FOR AIR CRAFT; TIMBER FOR
MARINE PURPOSES; SEASONING AND TREATMENT OF TIMBER; LOGS FOR PLYWOOD;
GLOSSARY OF TECHNICAL TERMS USED IN TIMBER TECHNOLOGY; STANDARD
DIMENSIONS FOR WOOD POLES OF INDIAN SPECIES FOR VARIOUS BREAKING LOADS;
MOISTURE CONTENT AND SPECIFICATION OF TIMBER FOR VARIOUS USES; METHODS OF
TESTING TIMBER; GRADING OF WOOD; JOINERY; METHOD OF TEST FOR THE TOXICITY OF
WOOD PRESERVATIVES TO MICRO ORGANISMS AND INSECTS, TIMBER IN BUILDING
CONSTRUCTION, FLOORS; GRADING OF TIMBER, SIZES OF GRADED TIMBER
STANDARDIZATION IN THE FIELD OF TIMBER STORES INCLUDING BAMBOO AND CANE
STORES SUCH AS WOODEN HANDLES, WOODEN CONTAINERS INCLUDING PLYWOOD TEA-
CHESTS, CANE BASKETS, BAMBOO TENT POLES ETC; AND ANY OTHER WOODENWARE
ITEMS NOT COVERED BY OTHER SECTIONAL COMMITTEE AND TO ADVISE THE LATER
COMMITTEES WHEREVER CALLED UPON TO DO SO

LIAISON ISO/TC 218 (O) TIMBER

ISO/PC 287(P) CHAIN OF CUSTODY OF WOOD & WOOD BASED PRODUCTS
ISO/TC 296(P) BAMBOO AND RATTAN

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 10 (Part 1):1990 Plywood tea-chests ― Specification: Oct 2020 S

Part 1 General (fifth revision)

2 IS 10 (Part 2):2013 Plywood tea-chests ― Specification: Aug 2018 S

Part 2 Plywood (sixth revision)

3 IS 10 (Part 3):1974 Plywood tea-chests ― Specification: Oct 2020 3 S

Part 3 Battens (fourth revision)

4 IS 10 (Part 4):1989 Plywood tea-chests ― Specification: Oct 2017 1 S

Part 4 Metal fittings (fifth revision)

5 IS 10 (Part 5):1976 Specification for plywood tea-chests: Oct 2020 S

Part 5 Assembly and packing (fourth revision)

6 IS 190:1991 Coniferous sawn timber (Baulks and scantlings) Oct 2020 S

― Specification (fourth revision)

7 IS 287:1993 Permissible moisture content for timber used for Oct 2017 C
different purposes ― Recommendations
(third revision)

8 IS 399:1963 Classification of commercial timbers and their Oct 2020 1 O

zonal distribution (first revision )

9 IS 401:2001 Preservation of timber ― Code of practice Oct 2016 1 C

(fourth revision)

10 IS 620:1985 Specification for wooden tool handles general Oct 2020 1 S

requirements (fourth revision)

37
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

11 IS 656:1988 Specification for logs for plywood (third revision) Oct 2017 S

12 IS 707:2011 Timber technology and utilization of wood, Oct 2016 1 T

bamboo and cane ― Glossary of terms
(third revision)

13 IS 876:1992 Wood poles for overhead power and Oct 2017 S

telecommunication lines ― Specification
(third revision)

14 IS 1140:1988 Specification for logs for matches Oct 2017 3 S

(second revision)

15 IS 1141:1993 Seasoning of timber ― Code of practice Oct 2020 C

(second revision)

16 IS 1150:2000 Trade names and abbreviated symbols for Oct 2020 1 O

timber species (third revision)

17 IS 1326:1992 Non-coniferous sawn timber (Baulks and Oct 2017 S

scantling) ― Specification (second revision)

18 IS 1331:1971 Specification for cut sizes of timber Oct 2016 S

(second revision) (Superseding IS 1629:1960)

19 IS 1503:1988 Specification for wooden packing cases Oct 2017 S

(third revision)

20 IS 1707:1979 Specification for wood wool for general Oct 2017 S

packaging purposes (first revision)

21 IS 1708 (Parts 1 to 18): Methods of testing of small specimens of timber Oct 2020 2 M
1986 (second revision):
Part 1 Determination of moisture content
Part 2 Determination of specific gravity
Part 3 Determination of volumetric shrinkage
Part 4 Determination of radial and tangential
shrinkage and fibre saturation point
Part 5 Determination of static bending strength
Part 6 Determination of static bending strength
Under two point loading
Part 7 Determination of impact bending
strength
Part 8 Determination of compressive strength
parallel to grain
Part 9 Determination of compressive strength
perpendicular to grain
Part 10 Determination of hardness under static
indentation
Part 11 Determination of shear strength parallel
to grain
Part 12 Determination of tensile strength parallel
to grain
Part 13 Determination of tensile strength
perpendicular to grain
Part 14 Determination of cleavage strength
parallel to grain
Part 15 Determination of nail and screw holding

38
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

power
Part 16 Determination of brittleness by Izod
impact
Part 17 Determination of brittleness by Charpy
impact
Part 18 Determination of torsional strength

22 IS 1898:1990 Timber for aircraft construction in converted form Oct 2020 1 S

(finished form) ― Specification (second revision)

23 IS 1900:1974 Methods of tests for wood poles (first revision) Oct 2017 M

24 IS 1902:2006 Preservation of bamboo and cane for non- Oct 2016 C

structural purposes ― Code of practice
(second revision)

25 IS 2133:1983 Specification for wooden tent pins Oct 2020 S

(second revision)

26 IS 2179:1979 Specification for converted timber for lorry bodies Oct 2020 S
(first revision)

27 IS 2203:1993 Wooden cross arms ― Specification Oct 2017 S

(second revision)

28 IS 2372:2021 Timber for cooling towers ― Specification S

(third revision)

29 IS 2377:1967 Tables for volumes of cut sizes of timber Oct 2017 O

(first revision)

30 IS 2408:1963 Methods of static tests of timber in structural Oct 2020 1 M

sizes

31 IS 2455:1990 Method of sampling of model trees and logs and Oct 2020 M
their conversion for timber testing
(second revision)

32 IS 2674:1988 Specification for battened plywood cases Oct 2017 1 S

(second revision)

33 IS 2683:1980 Guide for installation of impregnation plants for Oct 2020 C

timber (second revision)

34 IS 2753 (Part 1):1991 Methods for estimation of preservatives in Oct 2020 M

treated timber and in treating solutions:
Part 1 Determination of copper, arsenic,
chromium, zinc, boron, creosote and fuel oil
(first revision)

35 IS 2753 (Part 2):2014 Methods for estimation of preservatives in Mar 2019 1 M

treated timber and in treating solutions:
Part 2 Determination of copper (in copper
organic preservative salt) (second revision)

36 IS 2891:1975 Specification for wooden handles for felling axes Oct 2016 S
and hand axes (first revision)

39
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

37 IS 2892:1993 Wooden handles for picks and beaters ― Oct 2017 S

Specification (second revision)

38 IS 2893:1992 Wooden handles for adzes ― Specification Oct 2016 S

(second revision)

39 IS 2894:1987 Specification for wooden handles for wood Oct 2016 1 S

working chisels and gouges (first revision)

40 IS 2895:1990 Wooden handles for rasps, engineers' files and Oct 2016 S
engineers' scrapers ― Specification
(second revision)

41 IS 2896:1978 Specification for wooden handles for carpenters Oct 2016 S

augers (first revision)

42 IS 2897:1983 Specification for wooden handles for shovels Oct 2020 S

(first revision)

43 IS 2922:1975 Specification for wooden tent mallets Oct 2016 1 S

(first revision)

44 IS 3053:1977 Specification for cane baskets for general Oct 2020 S

purposes (first revision)

45 IS 3071:1981 Specification for wooden crates (first revision) Oct 2016 S

46 IS 3084:1989 Pencil slats ― Specification (second revision) Oct 2017 S

47 IS 3337:1978 Specification for ballies for general purposes Oct 2016 1 S

(first revision)

48 IS 3364 (Part 1):1976 Methods of measurement and evaluation of Oct 2020 1 M

defects in timber: Part 1 Logs (first revision)

49 IS 3364 (Part 2):1976 Methods of measurement and evaluation of Oct 2020 1 M

defects in timber: Part 2 Converted timber
(first revision)

50 IS 3386:1979 Specification for wooden fence posts Oct 2016 1 S

(first revision)

51 IS 3728:1985 Specification for wooden boxes for packaging of Oct 2020 S

apples (first revision)

52 IS 3731:1985 Specification for teak squares (first revision) Oct 2020 S

53 IS 3806:1966 Specification for wooden beaters Oct 2020 S

54 IS 4422:1985 Specification for willow clefts for cricket bats Oct 2020 S
(first revision)

55 IS 4423:1999 Hand-sawing of timber – Guide (first revision) Oct 2020 C

56 IS 4424:1967 Specification for timber for use in coal mines Oct 2020 1 S

57 IS 4650:1968 Specification for wooden anvil blocks Oct 2020 2 S

40
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

58 IS 4833:1993 Methods for field testing of preservatives in wood Oct 2017 M

(first revision)

59 IS 4873 (Part 1):2008 Methods of laboratory testing of wood Mar 2019 1 M

preservatives against fungi and borers (powder
post beetles): Part 1 Determination of threshold
values of wood preservatives against fungi
(second revision)

60 IS 4873 (Part 2):2021 Methods of laboratory testing of wood M

preservatives against fungi and borers (powder
post beetles) in wood and bamboo:
Part 2 Determination of threshold values of wood
preservatives against borers (powder post
beetles) in wood and bamboo (third revision)

61 IS 4895:1985 Specification for teak logs (first revision) Oct 2020 S

62 IS 4907:2004 Method of testing timber connector joints Oct 2020 M

(first revision)

63 IS 4953:1989 Wooden handles for hand hammers ― Oct 2017 S

Specification (second revision)

64 IS 4970:1973 Key for identification of commercial timbers Oct 2020 O

(first revision)

65 IS 5246:2000 Coniferous logs ― Specification (first revision) Oct 2017 S

66 IS 5247 (Part 1):1982 Specification for converted timber (coniferous): Oct 2020 S
Part 1 Light furniture (first revision)

67 IS 5247 (Part 2):1982 Specification for converted timber (coniferous): Oct 2020 S
Part 2 Packing cases and crates (first revision)

68 IS 5806:1970 Specification for non-coniferous timber Oct 2020 S

inconverted form for ammunition/explosives
boxes

69 IS 5942:1989 Wooden handles for Powrahs ― Specification Oct 2017 S

(first revision)

70 IS 5966:1993 Non-coniferous timber in converted form for Oct 2017 1 S

general purposes ― Specification (first revision)

71 IS 5978:1970 Code of practice for design of wood poles for Oct 2020 2 C
overhead power and telecommunication lines

72 IS 6056:1970 Specification for jointed wood poles for overhead Oct 2020 1 S
power and telecommunication lines

73 IS 6341:1971 Method for laboratory test for efficacy of wood Oct 2016 M
preservatives against soft rot

74 IS 6346:1971 Method of tests for timber props for mines Oct 2020 M

75 IS 6497:1990 Method of test for the efficacy of preservatives Oct 2020 M

and evaluating the natural durability of timbers
used in cooling towers (first revision)

41
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

76 IS 6534:1971 Guiding principles for grading and inspection of Oct 2020 C

timber

77 IS 6641:1985 Specification for wooden disc for tents Oct 2020 1 S

(first revision)

78 IS 6642:1986 Specification for mason's mallets (first revision) Oct 2020 S

79 IS 6643:1987 Specification for wooden pins for bivouac tents Oct 2016 S
(first revision)

80 IS 6644:1986 Specification for tinman's mallets (first revision) Oct 2020 S

81 IS 6656:1986 Specification for caulking mallets (first revision) Oct 2020 S

82 IS 6662:1993 Timber species suitable for wooden packaging Oct 2017 S

― Specification (second revision)

83 IS 6676:1986 Specification for bossing (plumbers), mallets Oct 2020 S

(first revision)

84 IS 6703:1972 Glossary of wooden packaging terms Oct 2016 T

85 IS 6707:1972 Specification for willow logs for artificial limbs Oct 2020 S

86 IS 6711:1972 Code of practice for maintenance of wood poles Oct 2020 C

for overhead power and telecommunication lines

87 IS 6729:1972 Specification for wooden paddles Oct 2020 S

88 IS 6791:1973 Method of testing natural durability of timber and Oct 2020 M

efficacy of the wood preservatives against
marine borers

89 IS 6874:2008 Method of tests for bamboos (first revision) Mar 2019 1 M

90 IS 7308:1999 Non-coniferous logs ― Specification Oct 2020 S

(first revision)

91 IS 7315:1974 Guidelines for design, installation and testing of Oct 2020 C

timber seasoning kilns (Compartment type with
cross-forced air circulation)

92 IS 7344:1974 Specification for bamboo tent poles Oct 2020 2 S

93 IS 7548:1992 Vase for store tent ― Specification (first revision) Oct 2016 S

94 IS 7549:1975 Specification for timber half wrought for sporting Oct 2020 S
rifles

95 IS 7698:1983 Specification for returnable wooden crates for Oct 2017 S

vegetables (first revision)

96 IS 7850:1975 Specification for wooden box for microscope Oct 2020 1 S

slides

97 IS 7992:1983 Specification for plywood cases for packing Oct 2017 S

tobacco for export (first revision)

42
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

98 IS 8001:1976 Specification for packaging of plywood, Oct 2016 2 S

blockboards and flush doors for export

99 IS 8242:1976 Methods of tests for split bamboos Oct 2020 M

100 IS 8292:1992 Evaluation of working quality of timber under Oct 2016 M

different wood working operations ― Method of
test (first revision)

101 IS 8295 (Part 1):1976 Specification for bamboo chicks: Part 1 Fine Oct 2017 S

102 IS 8295 (Part 2):1976 Specification for bamboo chicks: Part 2 Coarse Oct 2017 S

103 IS 8720:1978 Methods of sampling of timber scantlings from Oct 2016 1 M

depots and their conversion for testing

104 IS 8725:1978 Specification for wire bound wooden boxes Oct 2017 S

105 IS 8726:1978 Specification for wire bound wooden crates Oct 2017 S

106 IS 8745:1994 Methods of presentation of data of physical and Oct 2017 M

mechanical properties of timber (first revision)

107 IS 9096:2006 Preservation of bamboo for structural purposes Oct 2016 C

― Code of practice (first revision)

108 IS 9104:1979 Guide for storage and protection of logs and Oct 2020 C
sawn timber

109 IS 9561:1985 Code of practice for felling and conversion of Oct 2020 C
trees into logs (first revision)

110 IS 9576:1980 Guide for mill sawing of timber Oct 2020 C

111 IS 9590:1980 Specification for non-returnable wooden boxes Oct 2016 S

for horticulture produce

112 IS 10013 (Part 1):1981 Specification for water soluble type wood Oct 2020 S
preservatives: Part 1 Acid-copper-chrome (ACC)
preservative

113 IS 10013 (Part 2):1981 Specification for water soluble type wood Oct 2020 1 S
preservatives: Part 2 Copper-chrome-arsenic
(CCA) wood preservative

114 IS 10013 (Part 3):1981 Specification for water soluble type wood Oct 2020 S
preservatives: Part 3 Copper-chrome-boron
(CCB) wood preservative

115 IS 10145:1982 Specification for bamboo supports for Oct 2020 1 S

camouflaging equipment

116 IS 10394:1982 Specification for wooden sleepers for railway Oct 2020 1 S
track

117 IS 10402:1982 Specification for pine-needle hardboard boxes Oct 2020 1 S

for packaging of apples

43
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

118 IS 10420:1982 Method of determination of sound absorption Oct 2020 M

coefficient of timber by standing wave method

119 IS 10499:1983 Specification for wooden toggles Oct 2020 S

120 IS 10687:1983 Guidelines for nailing of large framed wooden Oct 2017 C
containers

121 IS 10753:1983 Code of practice for preservation of wooden Oct 2020 C

sleepers for railway track by pressure treatment

122 IS 10754:1983 Method of determination of thermal conductivity Oct 2020 M

of timber

123 IS 11100:1984 Specification for sweeping brooms Oct 2020 S

124 IS 11106:1984 Specification for carpenter's mallets Oct 2020 S

125 IS 11131:1984 Specification for wooden casks and barrels Oct 2017 S

126 IS 11215:1991 Moisture content of timber and timber products Oct 2020 M
― Methods for determination (first revision)

127 IS 11288:1985 Recommendations for off-road transportation of Oct 2020 O

timber

128 IS 12896:1990 Indian timbers for door and window shutters and Oct 2020 1 O
frames ― Classification

129 IS 13621:1993 Determination of dielectric constant of wood Oct 2017 M

under microwave frequencies ― Method of test

130 IS 13622:1993 Indian timbers for furniture and cabinets ― Oct 2017 O
Classification

131 IS 14960:2001 Preservative treated and seasoned sawn timber Mar 2019 S
from rubber wood (Hevea Brasiliensis) ―
Specification

132 IS 15455:2004 Grading rules for split canes Oct 2020 O

133 IS 15456:2004 Grading rules for unsplit canes Oct 2020 O

134 IS 15457:2004 Logs for production of sliced veneers ― Oct 2020 S

Specification (Superseding IS 5248:1988,
IS 6342:1987, & IS 13240:1991)

135 IS 15458:2004 Classification of Indian canes and their zonal Oct 2020 O
distribution

136 IS 15890:2010 Design, installation and testing of solar timber Aug 2019 C
seasoning kiln ― Guidelines

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

44
CED 11 DOORS, WINDOWS AND SHUTTERS
SCOPE STANDARDIZATION IN THE FIELD OF DOORS, WINDOWS, VENTILATORS, GATES AND
SHUTTERS MADE OF ANY MATERIAL

LIAISON ISO/TC 162 (O) DOORS AND WINDOWS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1003 (Part 1):2003 Timber panelled and glazed shutters ― Aug 2018 2 S
Specification: Part 1 Door shutters
(fourth revision)

2 IS 1003 (Part 2):1994 Timber panelled and glazed shutters ― Jan 2017 3 S
Specification: Part 2 Window and ventilator
shutters (third revision)

3 IS 1038:1983 Specification for steel doors, windows and Jan 2017 3 S

ventilators (third revision)

4 IS 1081:1960 Code of practice for fixing and glazing of metal Jan 2017 1 C
(steel and aluminium) doors, windows and
ventilators

5 IS 1361:1978 Specification for steel windows for industrial Jan 2017 2 S

buildings (first revision)

6 IS 1948:1961 Specification for aluminium doors, windows and Jan 2017 1 S

ventilators

7 IS 1949:1961 Specification for aluminium windows for industrial Jan 2017 1 S

buildings

8 *IS 2191 (Part 1):1983 Specification for wooden flush door shutters Jan 2017 2 S
(cellular and hollow core type): Part 1 Plywood
face panels (fourth revision)

9 *IS 2191 (Part 2):1983 Specification for wooden flush door shutters Jan 2017 2 S
(cellular and hollow core type): Part 2 Particle
board and hardboard face panels (third revision)

10 *IS 2202 (Part 1):1999 Wooden flush door shutters (solid core type) ― Jan 2017 4 S
Specification: Part 1 Plywood face panels
(sixth revision)

11 *IS 2202 (Part 2):1983 Specification for wooden flush door shutters (solid Jan 2017 2 S
core type): Part 2 Particle board and hardboard
face panels (third revision)

12 IS 4020 (Parts 1 to 16): Door shutters ― Methods of tests Aug 2018 1 M

1998 Part 1 General (third revision)
Part 2 Measurement of dimensions and 1
squareness (third revision) 1
Part 3 Measurement of general flatness 1
(third revision)
Part 4 Local planeness test (third revision)

45
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

Part 5 Impact indentation test (third revision)

Part 6 Flexure test (third revision) 1
Part 7 Edge loading test (third revision) 2
Part 8 Shock resistance test (third revision)
Part 9 Buckling resistance test (third revision)
Part 10 Slamming test (third revision)
Part 11 Misuse test (third revision) 2
Part 12 Varying humidity test (third revision)
Part 13 End immersion test (third revision)
Part 14 Knife test (third revision)
Part 15 Glue adhesion test (third revision)
Part 16 Screw withdrawal resistance test
(third revision)

13 IS 4021:1995 Timber door, window and ventilator frames ― Jan 2017 3 S

Specification (third revision)

14 IS 4043:1969 Recommendations for symbolic designation of Jan 2017 O

direction of closing and faces of doors, windows
and shutters

15 IS 4351:2003 Steel door frames ― Specification Aug 2018 1 S

(second revision)

16 IS 4913:1968 Code of practice for selection, installation and Jan 2017 C

maintenance of timber doors and windows

17 IS 6198:1992 Ledged, braced and battened timber door shutters Jan 2017 2 S
― Specification (second revision)

18 IS 6248:1979 Specification for metal rolling shutters and rolling Jan 2017 S
grills (first revision)

19 IS 10428:1983 Glossary of terms relating to doors Jan 2017 T

/ ISO 1804:1972

20 IS 10451:1983 Specification for steel sliding shutters (top hung Jan 2017 1 S
type)

21 IS 10521:1983 Specification for collapsible gates Jan 2017 1 S

22 IS 14856:2000 Glass fibre reinforced plastic (GRP) panel type Jan 2017 S
door shutters for internal use ― Specification

23 IS 15380:2003 Moulded raised high density fibre (HDF) panel Aug 2018 1 S
doors ― Specification

24 IS 15931:2012 Solid panel foam UPVC door shutters ― Jul 2017 S

Specification

25 IS 16073:2013 Bamboo – Jute composite panel door shutter ― Oct 2018 S

Specification

26 IS 16074:2013 Steel flush door shutters ― Specification Aug 2018 S

27 IS 16096:2013 Bamboo – Jute composite hollow core door Dec 2018 S

shutter ― Specification

46
 FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 11 (15390) Preliminary Draft Indian Standard Wooden flush door shutters (cellular, tubular
and hollow core type) — Specification: Part 1 Plywood face panels [fifth revision of
IS 2191 (Part 1)]

2 DOC:CED 11 (15391) Preliminary Draft Indian Standard Flush door shutters (cellular, tubular and hollow
core type) — Specification: Part 2 Particle board, high density fibre board, medium
density fibre board and hardboard face panels [fourth revision of IS 2191 (Part 2)]

3 DOC:CED 11 (15392) Preliminary Draft Indian Standard Flush door shutters (solid core type) —
Specification: Part 1 Plywood face panels [seventh revision of IS 2202 (Part 1)]

4 DOC:CED 11 (15393) Preliminary Draft Indian Standard Flush door shutters (soild core type) —
Specification: Part 2 Particle board, high density fibre board, medium density fibre
board and hardboard face panels [fourth revision of IS 2202 (Part 2)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

47
CED 12 FUNCTIONAL REQUIREMENTS IN BUILDINGS
SCOPE STANDARDIZATION IN THE FIELD OF FUNCTIONAL REQUIREMENTS INBUILDINGS:
a) FROM COMFORT POINT OF VIEW, SUCH AS SPACE DISTRIBUTION, ORIENTATION,
DAY-LIGHTING, VENTILATION, ACOUSTICS AND THERMAL COMFORTS;
b) FROM HEALTH AND SAFETY POINT OF VIEW;
c) FROM THE POINT OF VIEW OF ACCESSIBILITY FOR PERSONS WITH DISABILITY; AND
d) FROM THE POINT OF VIEW OF ENERGY REQUIREMENTS.

LIAISON ISO/TC 43/SC 2 (O) BUILDING ACOUSTICS

ISO/TC 59/SC 16 (O) ACCESSIBILITY AND USABILITY OF THE BUILT ENVIRONMENT

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1950:1962 Code of practice for sound insulation of non- Aug 2020 1 C

industrial buildings

2 IS 2440:1975 Guide for daylighting of buildings Oct 2018 C

(second revision)

3 IS 2526:1963 Code of practice for acoustical design of Aug 2020 1 C

auditoriums and conference halls

4 IS 3103:1975 Code of practice for industrial ventilation Oct 2018 C

(first revision)

5 IS 3362:1977 Code of practice for natural ventilation of Oct 2018 C

residential buildings (first revision)

6 IS 3483:1965 Code of practice for noise reduction in industrial Aug 2020 C

buildings

7 IS 3792:1978 Guide for heat insulation of non-industrial Oct 2018 C

buildings (first revision)

8 IS 4954:1968 Recommendations for noise abatement in town Aug 2020 C

planning

9 IS 4963:1987 Recommendations for buildings and facilities for Aug 2020 C

the physically handicapped (first revision)

10 IS 5499:1969 Code of practice for construction of underground Oct 2018 C

air-raid shelters in natural soil

11 IS 6060:1971 Code of practice for daylighting of factory Oct 2018 C

buildings

12 IS 6074:1971 Code for functional requirements of hotels, Aug 2020 2 C

IS 6074:1971 (B) restaurants and other food service
establishments

13 IS 7662 (Part 1):1974 Recommendations for orientation of buildings: Oct 2018 C

Part 1 Non-industrial buildings

14 IS 7942:1976 Code of practice for daylighting of educational Oct 2018 C

buildings

48
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

15 IS 8827:1978 Recommendations for basic requirements of Aug 2020 C

school buildings

16 IS 9736:1981 Glossary of terms applicable to acoustics in Aug 2020 T

buildings

17 IS 11050 (Part 1):1984 Rating of sound insulation in buildings and of Jan 2017 M
/ISO 717/1-1982 building elements: Part 1 Airborne sound
insulation in buildings and of interior building
elements

18 IS 11050 (Part 2):1984 Rating of sound insulation in buildings and of Jan 2017 M
/ISO 717/2-1982 building elements: Part 2 Impact sound
insulation

19 IS 11050 (Part 3):1984 Rating of sound insulation in buildings and of Jan 2017 M
/ISO 717/3-1982 building elements: Part 3 Airborne sound
insulation of facade elements and facade

20 IS 11907:1986 Recommendations for calculation of solar Jan 2017 C

radiation on buildings

21 IS 12332:1988 Code of practice for ventilation in petrochemical Oct 2018 C

plants and refineries

22 IS 13735:1993 Audible emergency evacuation signal ― Jan 2017 S

/ISO 8201-1987 Specification

23 SP 32 (S&T):1986 Handbook on functional requirements of O

industrial buildings (lighting and ventilation)

24 SP 41 (S&T):1987 Handbook on functional requirements of O

buildings (other than industrial buildings)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

49
CED 13 BUILDING CONSTRUCTION PRACTICES
SCOPE DRAWING UP OF CODES OF PRACTICE FOR BUILDING CONSTRUCTION AND
MAINTENANCE

LIAISON ISO/TC 59 (O) BUILDINGS AND CIVIL ENGINEERING WORKS

ISO/TC 59/SC 2 (O) TERMINOLOGY AND HARMONIZATION OF LANGUAGES
ISO/TC 59/SC 8 (O) SEALANTS
ISO/TC 59/SC 13 (O) ORGANIZATION OF INFORMATION ABOUT CONSTRUCTION WORKS
ISO/TC 165 (P) TIMBER STRUCTURES

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 883:2016 Design of structural timber in building ― Code of C

practice (fifth revision)

2 IS 965:1963 Equivalent metric units for scales, dimensions and Sep 2020 2 D
quantities in general construction work

3 IS 1414:1989 Fixing of wall coverings ― Code of practice Sep 2019 C

(first revision)

4 IS 1477 (Part 1):1971 Code of practice for painting of ferrous metals in Sep 2020 C
buildings: Part 1 Pretreatment (first revision)

5 IS 1477 (Part 2):1971 Code of practice for painting of ferrous metals in Sep 2020 C
buildings: Part 2 Painting (first revision)

6 IS 1597 (Part 1):1992 Construction of stone masonry: Part 1 Rubble Dec 2016 C
stone masonry ― Code of practice (first revision)

7 IS 1597 (Part 2):1992 Construction of stone masonry ― Code of Dec 2016 C

practice: Part 2 Ashlar masonry (first revision)

8 IS 1634:1992 Code of practice for design and construction of Dec 2016 C

wood stairs for houses (second revision)

9 IS 1649:1962 Code of practice for design and construction of Sep 2017 C

flues and chimneys for domestic heating
appliances

10 IS 1834:1984 Specification for hot applied sealing compounds Sep 2020 S

for joints in concrete (first revision)

11 IS 1838 (Part 1):1983 Specification for preformed fillers for expansion Sep 2020 1 S
joint in concrete pavement and structure (non-
extruding and resilient type): Part 1 Bitumen
impregnated fibre (first revision)

12 IS 1838 (Part 2):1984 Specification for preformed fillers for expansion Sep 2020 S
joint in concrete pavement and structure (non-
extruding and resilient type): Part 2 CNSL
Aldehyde resin and coconut pith

50
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

13 IS 1838 (Part 3):2011 Preformed fillers for expansion joints in concrete Dec 2016 1 S
pavements and structures (non-extruding and
resilient type) ― Specification: Part 3 Polymer
based

14 IS 1905:1987 Code of practice for structural use of unreinforced Sep 2017 1 C

masonry (third revision)

15 IS 1946:1961 Code of practice for use of fixing devices in walls, Sep 2017 C
ceilings and floors of solid construction

16 IS 2110:1980 Code of practice for insitu construction of walls in Sep 2017 C

buildings with soil-cement (first revision)

17 IS 2115:1980 Code of practice for flat roof finish: Mud phuska Sep 2017 C
(second revision)

18 IS 2116:1980 Specification for sand for masonry mortars Sep 2017 S

(first revision)

19 IS 2118:1980 Code of practice for construction of jack-arch Sep 2017 C

type of built-up floor or roof (first revision)

20 IS 2119:1980 Code of practice for construction of brick-cum- Sep 2017 C

concrete composite (Madras terrace) floor and
roof (first revision)

21 IS 2204:1962 Code of practice for construction of reinforced Sep 2020 C

concrete shell roof

22 IS 2212:1991 Brick works ― Code of practice (first revision) Sep 2019 C

23 IS 2250:1981 Code of practice for preparation and use of Sep 2020 C

masonry mortars (first revision)

24 IS 2338 (Part 1):1967 Code of practice for finishing of wood and wood- Sep 2020 C
based materials: Part 1 Operations and
workmanship
25 IS 2338 (Part 2):1967 Code of practice for finishing of wood and wood- Sep 2020 C
based materials: Part 2 Schedules

26 IS 2366:1983 Code of practice for nail-jointed timber Sep 2020 C

construction (first revision)

27 IS 2395 (Part 1):1994 Painting of concrete, masonry and plaster Sep 2019 C
surfaces ― Code of practice: Part 1 Operations
and workmanship (first revision)

28 IS 2395 (Part 2):1994 Painting of concrete, masonry and plaster Sep 2019 C
surfaces ― Code of practice: Part 2 Schedules
(first revision)

29 IS 2441:1984 Code of practice for fixing ceiling coverings Sep 2020 C

(first revision)

30 IS 2524 (Part 1):1968 Code of practice for painting of non-ferrous metals Sep 2020 C
in buildings: Part 1 Pretreatment

51
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

31 IS 2524 (Part 2):1968 Code of practice for painting of non-ferrous metals Sep 2020 C
in buildings: Part 2 Painting

32 IS 2527:1984 Code of practice for fixing rainwater gutters and Sep 2020 C
downpipes for roof drainage (first revision)

33 IS 2700:1987 Code of practice for roofing with wooden shingles Sep 2020 C
(first revision)

34 IS 2792:1964 Code of practice for design and construction of Sep 2020 C

stone slab over joist floor

35 IS 2858:1984 Code of practice for roofing with mangalore tiles Sep 2020 C
(first revision)

36 IS 3140:1965 Code of practice for painting asbestos cement Sep 2020 C

building products

37 IS 3414:1968 Code of practice for design and installation of Sep 2020 C

joints in buildings

38 IS 3548:1988 Code of practice for glazing in buildings Sep 2019 C

(first revision)

39 IS 3629:1986 Specification for structural timber in building Sep 2020 S

(first revision)

40 IS 3630:1992 Construction of non-load bearing gypsum block Dec 2016 C

partitions ― Code of practice (first revision)

41 IS 3670:1989 Construction of timber floors ― Code of practice Sep 2020 C

(first revision)

42 IS 4101 (Part 1):1967 Code of practice for external facings and veneers: Sep 2020 C
Part 1 Stone facing

43 IS 4101 (Part 2):1967 Code of practice for external facings and veneers: Sep 2020 C
Part 2 Cement concrete facing

44 IS 4101 (Part 3):1985 Code of practice for external cladding: Part 3 Wall Sep 2020 C
tiling and mosaics (first revision)

45 IS 4407:1967 Code of practice for reed walling Sep 2017 C

46 IS 4597:1968 Code of practice for finishing of wood and wood Sep 2020 C
based products with nitrocellulose and cold
catalysed materials

47 IS 4891:1988 Specification for preferred cut sizes of structural Sep 2019 S

timber (first revision)

48 IS 4920:1968 Glossary of terms applicable to roof coverings Sep 2020 T

49 IS 4924 (Part 1):1968 Method of test for nail jointed timber trusses: Sep 2020 M
Part 1 Destructive test

50 IS 4924 (Part 2):1968 Method of test for nail jointed timber trusses: Sep 2020 M
Part 2 Proof test

52
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

51 IS 4983:1968 Code of practice for design and construction of Sep 2020 C

nailed laminated timber beams

52 IS 5119 (Part 1):1968 Code of practice for laying and fixing of sloped Sep 2020 C
roof covering: Part 1 Slating

53 IS 5389:1969 Code of practice for laying of hardwood parquet Sep 2017 C

and wood block floors

54 IS 5390:1984 Code of practice for construction of timber ceilings Sep 2020 C

(first revision)

55 IS 6061 (Part 1):1971 Code of practice for construction of floor and roof Sep 2017 C
with joists and filler blocks: Part 1 With hollow
concrete filler blocks

56 IS 6061 (Part 2):1981 Code of practice for construction of floor and roof Sep 2020 C
with joists and filler blocks: Part 2 With hollow clay
filler blocks (first revision)

57 IS 6061 (Part 3):1981 Code of practice for construction of floor and roof Sep 2017 C
with joists and filler blocks: Part 3 With precast
hollow clay block joists and hollow clay filler blocks

58 IS 6061 (Part 4):1981 Code of practice for construction of floor and roof Sep 2017 C
with joists and filler blocks: Part 4 With precast
hollow clay block slab panels

59 IS 6313 (Part 1):1981 Code of practice for anti-termite measures in Sep 2020 C
buildings: Part 1 Constructional measures
(first revision)

60 IS 6313 (Part 2):2013 Code of practice for anti-termite measures in Dec 2018 C
buildings: Part 2 Pre-constructional chemical
treatment measures (third revision)

61 IS 6313 (Part 3):2013 Code of practice for anti-termite measures in Dec 2018 C
buildings: Part 3 Treatment for existing buildings
(third revision)

62 IS 6332:1984 Code of practice for construction of floors and Sep 2020 C

roofs using precast doubly-curved shell units
(first revision)

63 IS 6509:1985 Code of practice for installation of joints in Sep 2020 C

concrete pavements (first revision)

64 IS 7683:1975 Code of practice for design, fabrication and Sep 2017 C

maintenance of nail-jointed timber posts from
small dimensional timber for overhead electric
distribution lines for low voltages

65 IS 9472:1980 Code of practice for laying of mosaic parquet Sep 2017 C

flooring

66 IS 9954:1981 Pictorial surface preparation standards for painting Sep 2020 1 O

of steel surfaces

53
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

67 IS 10388:1982 Specification for corrugated coir, woodwool, Sep 2020 S

cement roofing sheets

68 IS 10439:1983 Code of practice for patent glazing Sep 2020 C

69 IS 10440:1983 Code of practice for construction of RB and RBC Sep 2020 C

floors and roofs

70 IS 10566:1983 Methods of tests for preformed fillers for Sep 2020 M

expansion joints in concrete paving and structural
construction

71 IS 10957:1999 Joints in buildings - Vocabulary (first revision) Sep 2019 T

/ISO 2444:88

72 IS 10958:1984 General check list of functions of joints in building Sep 2017 O

/ISO 3447:75

73 IS 10959:2017 Glossary of terms for sealants for building T

/ISO 6927:2012 purposes(first revision)

74 IS 11096:1984 Code of practice for design and construction of Sep 2020 C

bolt jointed timber construction

75 IS 11134:1984 Code of practice for setting out of buildings Sep 2020 C

76 IS 11433 (Part 1):1985 Specification for one-part gun-grade polysulphide- Sep 2020 S
based joints sealants: Part 1 General
requirements

77 IS 11433 (Part 2):1986 Specification for one-part gun-grade polysulphide- Sep 2020 M
based joint sealants: Part 2 Methods of tests

78 IS 11817:1986 Classification of joints in buildings for Sep 2017 O

/ISO 7727:84 accommodation of dimensional deviations during
construction

79 IS 11818:1986 Method of test for laboratory determination of air Sep 2017 M

/ISO 6589:83 permeability of joints in buildings

80 IS 12093:1987 Code of practice for laying and fixing of sloped Sep 2017 C
roof covering using plain and corrugated
galvanized steel sheets

81 IS 12118 (Part 1):1987 Specification for two-part polysulphide-based Sep 2017 S

sealants: Part 1 General requirements

82 IS 12118 (Part 2):1987 Specification for two-part polysulphide-based Sep 2017 M

sealants: Part 2 Methods of tests

83 IS 12506:1988 Code of practice for improved thatching of roof Sep 2019 C

with rot and fire retardant treatment

84 IS 12727:1989 No-fines cast in situ cement concrete ― Code of Sep 2020 C

practice

85 IS 13077:1991 Preparation and use of mud mortar in masonry ― Aug 2016 O

Guide

54
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

86 IS 14428:1997 Painting of structures in aggressive chemical May 2018 O

environment ― Guidelines

87 IS 15183 (Part 1):2018 Maintenance management of buildings ― O

Guidelines: Part 1 General (first revision)

88 IS 15183 (Part 2):2018 Maintenance management of buildings ― O

Guidelines: Part 2 Finance (first revision)

89 IS 15183 (Part 3):2018 Maintenance management of buildings ― O

Guidelines: Part 3 Labour (first revision)

90 IS 15345:2003 Installation of frameless door and window shutters May 2018 C

― Code of practice

91 IS 15912:2018 Structural design using bamboo ― Code of C

practice (first revision)

92 IS 16231 (Part 1):2019 Use of glass in buildings ― Code of practice: C

Part 1 General methodology for selection
(first revision)

93 IS 16231 (Part 2):2019 Use of glass in buildings ― Code of practice: C

Part 2 Energy and light (first revision)

94 IS 16231 (Part 3):2019 Use of glass in buildings ― Code of practice: C

Part 3 Fire and loading (first revision)

95 IS 16231 (Part 4):2019 Use of glass in buildings ― Code of practice: C

Part 4 Safety related to human impact
(first revision)

96 SP 1650:1973 Standard colours for building and decorative O

finishes (with supplement)

97 SP 1650 Supplement: Supplement to standard colours for building and O

1973 decorative finishes

98 SP 20 (S&T):1991 Handbook on masonry design and construction O

(first revision)

99 SP 21:2005 Summaries of Indian Standards for building O

materials (first revision)

100 SP 25 (S&T):1984 Handbook on causes and prevention of cracks in O

building

101 SP 33 (S&T):1986 Handbook on timber engineering O

102 SP 62 (S&T):1997 Handbook on building construction practices O

(excluding electrical work)

55
 FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 13 (15756) Draft Indian Standard Anti-termite measures in buildings — Code of practice:
Part 2 Pre-Constructional Chemical Treatment Measures [fourth revision of
IS 6313 (Part 2)]

2 DOC:CED 13 (16813) Draft Indian Standard Anti-termite measures in buildings — Code of practice:
Part 3 Treatment for Existing Buildings [fourth revision of IS 6313 (Part 3)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

56
CED 15 BUILDER'S HARDWARE
SCOPE STANDARDIZATION IN THE FIELD OF BUILDER'S HARDWARE, SUCH AS DOORS, WINDOW AND
FURNITURE FITTINGS LIKEHINGES, HANDLES, SLIDING BOLTS, DOOR CLOSURE, FLOOR
SPRING, PANIC EXIT HARDWARE, LATCHES, CATLHES, DRAWER RUNNERS, ETC.

LIAISON ISO/TC 136 (O) FURNITURE

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 204 (Part 1):1991 Tower bolts ― Specification: Part 1 Ferrous metals Jan 2021 3 S
(fifth revision)

2 IS 204 (Part 2):1992 Tower bolts ― Specification: Part 2 Non-ferrous Jan 2017 3 S
metals (fifth revision)

3 IS 205:1992 Non-ferrous metal butt hinges ― Specification Jan 2017 2 S

(fourth revision)

4 IS 206:2010 Tee and strap hinges ― Specification Jan 2017 S

(fifth revision)

5 IS 208:2020 Door handles ― Specification (sixth revision) S

6 IS 281:2009 Mild steel sliding door bolts for use with padlocks Sep 2018 1 S
― Specification (fourth revision)

7 IS 362:1991 Parliament hinges ― Specification (fifth revision) Jan 2021 2 S

8 IS 363:1993 Hasps and staples ― Specification Sep 2018 S

(fourth revision)

9 IS 364:1993 Fanlight catch ― Specification (third revision) Sep 2018 S

10 IS 452:1973 Specification for door spring, rat-tail type Jan 2021 S

(second revision)

11 IS 453:1993 Double-acting spring hinges ― Specification Sep 2018 1 S

(third revision)

12 IS 1019:1974 Specification for rim latches (second revision) Jan 2017 1 S

13 IS 1341:2018 Steel butt hinges — Specification (sixth revision) 1 S

14 IS 1823:1980 Specification for floor door stoppers Jan 2017 S

(third revision)

15 IS 1837:1966 Specification for fanlight pivots (first revision) Jan 2021 1 S

16 IS 2681:1993 Non-ferrous metal sliding door bolts (aldrops) for Sep 2018 2 S
use with padlocks ― Specification (third revision)

17 IS 3564:1995 Hydraulically regulated door closers ― Sep 2018 S

Specification (fourth revision)

57
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

18 IS 3818:1992 Continuous (Piano) hinges ― Specification Jan 2017 2 S

(third revision)

19 IS 3828:1966 Specification for ventilator chains Jan 2021 S

20 IS 3843:1995 Steel back flap hinges ― Specification Sep 2018 S

(second revision)

21 IS 4621:1975 Specification for indicating bolts for use in public Jan 2021 S
baths and lavatories (first revision)

22 IS 4992:1975 Specification for door handles for mortice locks Jan 2021 S
(vertical type) (first revision)

23 IS 5187:1972 Specification for flush bolts (first revision) Jan 2021 1 S

24 IS 5899:1970 Specification for bathroom latches Jan 2017 1 S

25 IS 6315:1992 Floor springs (hydraulically regulated) for heavy Jan 2017 1 S

doors ― Specification (second revision)

26 IS 6318:1971 Specification for plastic window stays and Jun 2020 1 S

fasteners

27 IS 6343:1982 Specification for door closers (pneumatically Jan 2021 S

regulated) for light doors weighing up to 40 kg
(first revision)

28 IS 7196:1974 Specification for hold fast Jan 2017 2 S

29 IS 7197:1974 Specification for double action floor springs Jan 2021 S

(without oil check) for heavy doors

30 IS 7534:1985 Specification for sliding locking bolts for use with Jan 2021 S
padlocks (first revision)

31 IS 8756:1978 Specification for mortice ball catches for use in Jan 2017 S
wooden almirahs

32 IS 9106:1979 Specification for rising butt hinges Jan 2017 1 S

33 IS 9460:1980 Specification for flush drop handle for drawers Jan 2017 S

34 IS 9899:1981 Specification for hat, coat and wardrobe hooks Jan 2017 S

35 IS 10019:1981 Specification for mild steel stays and fasteners Jan 2017 S

36 IS 10090:1982 Specification for numericals Jan 2021 S

37 IS 10342:1982 Specification for curtain rail system Jan 2021 S

38 IS 12817:2020 Stainless steel butt hinges ― Specification S

(third revision)

39 IS 12867:1989 PVC handrail covers ― Specification Jun 2020 1 S

40 IS 14912:2001 Door closers, concealed type (hydraulically Jan 2017 S

regulated) ― Specification

58
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

41 IS 15833:2009 Stainless steel tower bolts ― Specification Sep 2018 S

42 IS 15834:2020 Stainless steel sliding door bolts (aldrops) for use S

with padlocks ― Specification (first revision)

43 IS 17296:2020 Stainless steel door stoppers ― Specification S

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 15 (16987) Draft Indian Standard Pull handles ― Specification

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

59
CED 20 WOOD AND OTHER LIGNOCELLULOSIC PRODUCTS
SCOPE STANDARDIZATION IN THE FIELD OF WOOD (AND OTHER LIGNOCELLULOSIC MATERIALS)
BASED PANEL PRODUCTS INCLUDING COMPOSITE WOOD PANEL PRODUCTS HAVING
MINERAL/POLYMERIC MATERIALS.
LIAISON ISO/TC 89 (O) WOOD BASED PANELS
ISO/TC 89/SC 1 (O) FIBRE BOARDS
ISO/TC 89/SC 2 (O) PARTICLE BOARDS
ISO/TC 89/SC 3 (O) PLYWOOD
ISO/TC 296 (P) BAMBOO AND RATTAN

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 303:1989 Plywood for general purposes ― Specification Feb 2018 6 S

(third revision)
2 IS 652:1960 Specification for wooden separators for lead-acid Oct 2019 S
storage batteries

3 IS 709:1974 Specification for medium strength aircraft Oct 2019 2 S

plywood (first revision)

4 IS 710:2010 Marine plywood ― Specification Mar 2017 S

(second revision)
5 IS 848:2006 Synthetic resin adhesives for plywood (phenolic Mar 2017 2 S
and amino plastic) ― Specification
(second revision)

6 IS 851:1978 Specification for synthetic resin adhesives for Oct 2019 2 S

construction work (non-structural) in wood
(first revision)
7 IS 852:1994 Animal glue for general wood-working purposes Oct 2019 S
― Specification (second revision)
8 IS 1328:1996 Veneered decorative plywood ― Specification Mar 2017 6 S
(third revision)

9 IS 1508:1972 Specification for extenders for use in synthetic Oct 2019 S

resin adhesives (urea-formaldehyde) for plywood
(first revision)

10 IS 1658:2006 Fibre hardboards ― Specification (third revision) Mar 2017 S

11 IS 1659:2004 Block boards ― Specification (fourth revision) Oct 2019 2 S

12 IS 1734 (Parts 1 to 20): Methods of test for plywood (second revision): Feb 2018 M
1983 Part 1 Determination of density and moisture 1
content
Part 2 Determination of resistance to dry heat 2
Part 3 Determination of fire resistance 2
Part 4 Determination of glue shear strength
Part 5 Test for adhesion of plies 2
Part 6 Determination of water resistance 1
Part 7 Mycological test
Part 8 Determination of pH value 1
Part 9 Determination of tensile strength
Part 10 Determination of compressive strength
Part 11 Determination of static bending strength

60
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

Part 12 Determination of scarf joint strength

Part 13 Determination of panel shear strength
Part 14 Determination of plate shear strength
Part 15 Central loading of plate test
Part 16 Vibration of plywood plate test
Part 17 Long time loading test of plywood strips
Part 18 Impact resistance test on the surface of
plywood
Part 19 Determination of nail and screw holding
power
Part 20 Acidity and alkalinity resistance test
13 IS 2380 (Parts 1 to 21): Methods of test for wood particle boards and Feb 2018 4 M
1977 boards from other lignocellulosic materials:
Part 1 Preparation and conditioning of test
specimens
Part 2 Accuracy of dimensions of boards
Part 3 Determination of moisture content and
density
Part 4 Determination of static bending strength
(modulus of rupture and modulus of
elasticity in bending)
Part 5 Determination of tensile strength
perpendicular to Surface
Part 6 Determination of tensile strength parallel
to surface
Part 7 Determination of compression
perpendicular to plane of the board
Part 8 Compression parallel to surface test
Part 9 Determination of resistance to shear in
plane of the board
Part 10 Falling hammer impact test
Part 11 Surface hardness
Part 12 Central loading of plate test
Part 13 Long time loading bending test
Part 14 Screw and nail withdrawal test
Part 15 Lateral nail resistance
Part 16 Determination of water absorption
Part 17 Determination of swelling in water
Part 18 Determination of mass and dimensional
Changes caused by moisture changes
Part 19 Durability cyclic test for interior use
Part 20 Accelerated weathering cyclic test for
Exterior use
Part 21 Planeness test under uniform moisture
content
14 IS 2380 (Part 22):1981 Method of test for wood particle boards and Feb 2018 1 M
boards from other lignocellulosic materials:
Part 22 Determination of surface glueability test
15 IS 2380 (Part 23):1981 Method of test for wood particle boards and Feb 2018 M
boards from other lignocellulosic materials:
Part 23 Vibration tests for particle boards

16 IS 3087:2005 Particle boards of wood and other lignocellulosic Feb 2020 5 S

materials (medium density) for general purposes
― Specification (second revision)

61
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

17 IS 3097:2006 Veneered particle boards ― Specification Mar 2017 S

(second revision)
18 IS 3129:1985 Specification for low density particle boards Feb 2020 4 S
(first revision)

19 IS 3308:1981 Specification for wood wool building slabs Feb 2018 2 S

(first revision)

20 IS 3348:1965 Specification for fibre insulation boards Oct 2019 2 S

21 IS 3478:1966 Specification for high density wood particle Feb 2018 4 S

boards
22 IS 3513 (Part 1):1989 Specification for resin treated compressed wood Oct 2019 3 S
laminates (compregs): Part 1 For electrical
purposes (first revision)

23 IS 3513 (Part 2):1989 Specification for resin treated compressed wood Feb 2018 2 S
laminates (compregs): Part 2 For chemical
purposes (first revision)

24 IS 3513 (Part 3):1989 Specification for resin treated compressed wood Feb 2018 2 S
laminates (compregs): Part 3 For general
purposes (first revision)

25 IS 3513 (Part 4):1966 Specification for resin treated compressed wood Oct 2019 M
laminates (compreg): Part 4 Sampling and tests

26 IS 4834:1968 Specification for veneered-wood boards for Feb 2020 2 S

packing cases

27 IS 4835:1979 Specification for polyvinyl acetate dispersion Oct 2019 2 S

based adhesives for wood (first revision)

28 IS 4859:1968 Specification for high strength aircraft plywood Oct 2019 3 S

29 IS 4990:2011 Plywood for concrete shuttering works ― Mar 2017 S

Specification (third revision)
30 IS 5509:2021 Fire retardant plywood ― Specification S
(third revision)
31 IS 5539:1969 Specification for preservative treated plywood Oct 2019 4 S
32 IS 7316:1974 Specification for decorative plywood using Feb 2018 4 S
plurality of veneers for decorative faces
33 IS 7638:1999 Wood/lignocellulosic based panel products ― Jul 2018 3 M
Methods of sampling (second revision)

34 IS 9188:1979 Performance requirements for adhesives for Oct 2019 S

structural laminated wood products for use under
exterior exposure condition
35 IS 9307 (Part 1):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 1 Flexure test
36 IS 9307 (Part 2):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 2 Edgewise
compression test

62
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

37 IS 9307 (Part 3):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 3 Flatwise
compression test
38 IS 9307 (Part 4):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 4 Shear test

39 IS 9307 (Part 5):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 5 Flatwise tension
test
40 IS 9307 (Part 6):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 6 Flexure creep test
41 IS 9307 (Part 7):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 7 Cantilever vibration
test
42 IS 9307 (Part 8):1979 Methods of test for wood-based structural Oct 2019 M
sandwich construction: Part 8 Weathering test

43 IS 10701:2012 Structural plywood ― Specification (first revision) Mar 2017 S

44 IS 12053:1987 Code of practice for the preparation and Feb 2020 C

application of putty for repairing plywood and
other wood based panels

45 IS 12077:1987 Code of practice for testing of timbers for Feb 2020 1 C

plywood manufacture

46 IS 12120:1987 Code of practice for preservation of plywood and Feb 2020 3 C

other panel products

47 IS 12406:2003 Medium density fibre boards for general purpose Feb 2018 5 S
― Specification (first revision)

48 IS 12823:2015 Prelaminated particle boards from wood and Feb 2020 1 S

other Iignocellulosic material ― Specification
(first revision)

49 IS 13745:2020 Method for determination of formaldehyde M

content in wood-based panels by extraction
method called perforator method (first revision)

50 IS 13957:1994 Metal faced plywood ― Specification Oct 2019 1 S

51 IS 13958:1994 Bamboo mat board for general purposes ― Oct 2019 4 S

Specification

52 IS 14276:2016 Cement bonded particle boards ― Specification S

(first revision)

53 IS 14315:1995 Commercial veneers ― Specification Oct 2019 1 S

54 IS 14587:1998 Prelaminated medium density fibre board ― Jul 2018 9 S

Specification

55 IS 14588:1999 Bamboo mat-veneer composite for general Jul 2018 3 S

purposes ― Specification

56 IS 14616:1999 Laminated veneer lumber ― Specification Jul 2018 4 S

63
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

57 IS 14842:2000 Coir veneer board for general purposes ― Feb 2020 3 S

Specification

58 IS 15476:2004 Bamboo mat corrugated sheets ― Specification Oct 2019 4 S

59 IS 15491:2004 Medium density coirboards for general purposes Oct 2019 1 S

― Specification

60 IS 15512:2004 Selection and use of various types of medium Oct 2019 C

density fibre boards ― Code of practice

61 IS 15684:2006 Use of extenders for use in synthetic resin Mar 2017 1 C

adhesives (urea-formaldehyde) for plywood ―
Code of practice

62 IS 15786:2008 Prelaminated cement bonded particle board ― Jul 2018 S

Specification

63 IS 15791:2007 Museum plywood ― Specification Jul 2018 S

64 IS 15877:2010 Coir faced block boards ― Specification Mar 2017 S

65 IS 15878:2010 Coir hardboard for general purposes ― Mar 2017 S

Specification

66 IS 15932 (Part 1):2012 Selection and use of various types of Mar 2017 C
lignocellulosic panel products ― Code of
practice: Part 1 Medium density particle boards

67 IS 15932 (Part 2):2017 Selection and use of various types of C

lignocellulosic panel products ― Code of
practice: Part 2 Hardboard [Superseding
IS 15973 (Part 2):2013]

68 IS 15972:2012 Bamboo-Jute corrugated and semi-corrugated Mar 2017 1 S

sheets ― Specification

69 IS 16171:2014 Veneer laminated lumber ― Specification Feb 2019 S

70 IS/ISO 12460-1:2007 Wood based panels ‒ Determination of Mar 2017 M

formaldehyde release: Part 1 Formaldehyde
emission by the 1-cubic-metre chamber method

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 20 (15037) Draft Indian Standard Flattened bamboo — Specification

2 DOC:CED 20 (15460) Draft Indian Standard BWP grade bamboo mat board — Specification

3 DOC:CED 20 (15461) Draft Indian Standard BWP grade bamboo mat-veneer board — Specification

4 DOC:CED 20 (15717) Draft Indian Standard Medium density fibre board — Specification (second revision
of IS 12406)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

64
CED 22 FIRE FIGHTING
SCOPE I) FIRE FIGHTING EQUIPMENT INCLUDING WATER FITTINGS
II) FIRE FIGHTING UNITS
III) FIRE DETECTION AND FIRE ALARM SYSTEMS, AND
IV) HELMETS

LIAISON ISO/TC 21 (O) EQUIPMENT FOR FIRE PROTECTION AND FIRE FIGHTING
ISO/TC 21/SC 2 (O) MANUALLY TRANSPORTABLE FIRE EXTINGUISHERS
ISO/TC 21/SC 3 (O) FIRE DETECTION AND ALARM SYSTEM
ISO/TC 21/SC 5 (O) FIXED FIRE FIGHTING SYSTEMS USING WATER
ISO/TC 21/SC 6 (O) FOAM AND POWDER MEDIA AND FIRE FIGHTING SYSTEMS USING
FOAM AND POWDER
ISO/TC 21/SC 8 (O) GASEOUS MEDIA AND FIRE FIGHTING SYSTEMS USING GAS
ISO/TC 21/SC 11(O) SMOKE AND HEAT CONTROL SYSTEMS AND COMPONENTS
ISO/TC 94/SC 1 (P) HEAD PROTECTION

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

1 IS 884:1985 Specification for first-aid hose reel for fire fighting Dec 2020 3 S
(first revision)

2 IS 901:1988 Specification for couplings, double male and Sep 2017 S

double female, instantaneous pattern for fire
fighting (third revision)

3 IS 902:1992 Suction hose couplings for fire fighting purposes Sep 2017 S
― Specification (third revision)

4 IS 903:1993 Fire hose delivery couplings, branch pipe, nozzles Aug 2018 4 S
and nozzle spanner ― Specification
(fourth revision)

5 IS 904:1983 Specification for 2-way and 3-way suction Dec 2020 1 S

collecting heads for fire fighting purposes
(second revision)

6 IS 905:1980 Specification for delivery breechings, dividing and Sep 2017 S

collecting instantaneous pattern for fire fighting
purposes (second revision)

7 *IS 906:1988 Specification for revolving branch pipe for fire Dec 2020 S
fighting (third revision)

8 IS 907:1984 Specification for suction strainers, cylindrical type Dec 2020 S

for fire fighting purposes (second revision)

9 IS 908:1975 Specification for fire hydrant, stand post type Dec 2020 1 S
(second revision)

10 IS 909:1992 Underground fire hydrant, sluice valve type ― Sep 2017 S

Specification (third revision)

11 IS 910:1980 Specification for combined key for hydrant, Sep 2017 1 S

hydrant cover and lower valve (second revision)

12 IS 926:1985 Specification for fireman's axe (second revision) Dec 2020 S

65
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

13 IS 927:1981 Specification for fire hooks (second revision) Sep 2017 2 S

14 IS 928:1984 Specification for fire bells (second revision) Dec 2020 S

15 IS 937:1981 Specification for washers for water fittings for fire Sep 2017 2 S
fighting purposes (second revision)

16 IS 939:1977 Specification for snatch block for use with fibre Sep 2017 S
rope for fire brigade use (first revision)

17 IS 941:1985 Specification for blower and exhauster for fire Dec 2020 2 S
fighting (second revision)

18 IS 942:1982 Functional requirements for 275 l/min portable Dec 2020 O

pump set for fire fighting (second revision)

19 IS 943:1979 Functional requirements for 680-l/min trailer pump Aug 2018 2 O

for fire brigade use (second revision)

20 IS 944:1979 Functional requirements for 1800-l/min trailer Sep 2017 1 O

pump for fire brigade use (second revision)

21 IS 947:1985 Functional requirements for towing tender for Sep 2017 1 O

trailer fire pump for fire brigade use (first revision)

22 IS 948:1983 Functional requirements for water tender type `A' Dec 2020 1 O
for fire brigade use (second revision)

23 IS 949:2012 Emergency (rescue) tender for fire brigade use ― Mar 2017 O
Functional requirements (second revision)

24 *IS 950:2012 Functional requirements for water tender, Type B Oct 2017 O
for fire brigade use (third revision)

25 IS 951:2003 Functional requirements for crash tender for air Aug 2018 O
fields (fourth revision)

26 IS 952:2012 Fog nozzle for fire brigade use ― Specification Jun 2017 S
(second revision)

27 IS 955:1980 Functional requirements for dry powder tender for Aug 2018 1 O
fire brigade use (first revision)

28 IS 956:2004 Functional requirements for rescue tender for air Jan 2020 O
fields (second revision)

29 IS 957:1967 Specification for control van for fire brigade use Dec 2020 3 S

30 IS 1941 (Part 1):1976 Functional requirements for electric motor sirens: Sep 2017 O
Part 1 AC, 3-Phase, 50 Hz, 415 Volts type
(second revision)

31 *IS 2097:2012 Foam making branch pipe and foam inductor― Jun 2017 S
Specification (second revision)

32 IS 2175:1988 Specification for heat sensitive fire detectors for Dec 2020 S
use in automatic fire alarm system
(second revision)

66
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

33 *IS 2189:2008 Selection, installation and maintenance of Aug 2018 C

automatic fire detection and alarm system ―
Code of practice (fourth revision)

34 *IS 2190:2010 Selection, installation and maintenance of first- Dec 2020 2 C

aid fire extinguishers ― Code of practice
(fourth revision)

35 IS 2546:1974 Specification for galvanized mild steel fire bucket Dec 2020 2 S
(first revision)

36 IS 2696:1974 Functional requirements for 1125-l/min light fire Sep 2017 2 O

engine (first revision) (Superseding IS 938)

37 IS 2745:1983 Specification for non-metal helmet for firemen and Dec 2020 3 S
civil defence personnel (second revision)

38 IS 2871:2012 Branch pipe, universal for fire fighting purposes ― Jun 2017 S
Specification (second revision)

39 IS 2925:1984 Specification for industrial safety helmets Dec 2020 4 S

IS 2925:1984 (B) (second revision)

40 IS 2930:1980 Functional requirements for hose laying tender for Sep 2017 1 O
fire brigade use (first revision)

41 IS 3582:1984 Specification for basket strainers for fire fighting Dec 2020 S
purposes (cylindrical type)

42 IS 3744:1985 Specification for hose binding machine Dec 2020 S

(first revision)

43 *IS 3844:1989 Code of practice for installation and maintenance Dec 2020 C
of internal fire hydrants and hose reels on
premises (first revision)

44 IS 4151:2015 Protective helmet for two wheeler riders ― Dec 2020 2 S

Specification (fourth revision)

45 IS 4308:2019 Dry chemical powders for fire fighting BC, ABC 4 S

and D types ― Specification (third revision)

46 IS 4571:1977 Specification for aluminium extension ladders for Dec 2020 5 S

fire brigade use (first revision)

47 IS 4643:1984 Specification for suction wrenches for fire brigade Dec 2020 S
use (first revision)

48 IS 4862 (Part 1):1986 Specification for portable fire extinguishers for Dec 2020 3 S
aircraft: Part 1 Halon 1211 Type (first revision)

49 IS 4927:1992 Unlined flax canvas hose for fire fighting ― Sep 2017 2 S
Specification (first revision)

50 IS 4928:1986 Specification for delivery valve for centrifugal fire Dec 2020 S
pump outlets (first revision)

67
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

51 IS 4947:2006 Gas cartridges for use in fire extinguishers ― Feb 2017 1 S

Specification (third revision)

52 IS 4989:2018 Foam concentrate for producing mechanical foam S

for fire fighting ― Specification
(fourth revision)

53 IS 5131:2002 Dividing breeching with control for fire brigade use Sep 2017 S
― Specification (second revision)

54 IS 5290:1993 Landing valves ― Specification (third revision) Aug 2018 6 S

55 IS 5486:1985 Specification for quick release knife (first revision) Dec 2020 S

56 IS 5505:1985 Specification for multi-edged rescue axe (non- Dec 2020 S

wedging) (first revision)

57 IS 5612 (Part 1):1977 Specification for hose-clamps and hose-bandages Sep 2017 1 S
for fire brigade use: Part 1 Hose-clamps
(first revision)

58 IS 5612 (Part 2):1977 Specification for hose-clamps and hose bandages Sep 2017 S
for fire brigade use: Part 2 Hose bandages
(first revision)

59 IS 5714:1981 Specification for hydrant, stand-pipe for fire Sep 2017 1 S

fighting (first revision)

60 IS 5888:1970 Code of practice for design and construction of Dec 2020 C

fire service drill- tower

61 IS 5896 (Part 1):1970 Code of practice for selection, operation and Dec 2020 C
maintenance of special fire fighting appliances:
Part 1 Combined foam and CO2 crash tender

62 IS 5896 (Part 3):1975 Code of practice for selection, operation and Sep 2017 C
maintenance of fire fighting appliances:
Part 3 Turntable ladders

63 IS 6026:1985 Specification for hand-operated sirens Dec 2020 S

(first revision)

64 IS 6067:1983 Functional requirements for water tender type `X' Dec 2020 O
for fire brigade use (first revision)

65 IS 6070:1983 Code of practice for selection, operation and Dec 2020 C

maintenance of trailer fire pumps, portable
pumps, water tenders and motor fire engines
(first revision)

66 IS 7673:2004 Fire fighting equipment ― Glossary of terms Aug 2018 T

(first revision)

67 IS 7692:1993 Headforms for testing of helmets ― Specification Aug 2018 S

(first revision)

68 IS 8090:1976 Specification for couplings, branch pipe, nozzle Dec 2020 1 S

used in hose reel tubing for fire fighting

68
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

69 IS 8096:1992 Fire beaters ― Specification (first revision) Sep 2017 S

70 IS 8423:1994 Controlled percolating hose for fire fighting ― Dec 2020 3 S

Specification (first revision)

71 *IS 8442:2008 Stand post type water and foam monitor for fire Aug 2018 O
fighting ― Specification (first revision)

72 IS 9562:1980 Specification for non-metal helmet for police force Sep 2017 5 S

73 *IS 9668:1990 Provision and maintenance of water supplies for Dec 2020 C
fire fighting ― Code of practice (first revision)

74 IS 9695:1980 Methods of sampling of helmets Dec 2020 M

75 *IS 9972:2002 Specification for automatic sprinkler heads for fire Sep 2017 S
protection service (first revision)

76 IS 9973:1981 Specification for visor for scooter helmets Sep 2017 1 S

77 IS 9995:1981 Specification for visor for non-metal police and Sep 2017 1 S
firemen's helmet

78 IS 10460:1983 Functional requirements for small foam tender for Dec 2020 1 O
fire brigade use

79 IS 10993:1984 Functional requirements for 2000-kg dry powder Dec 2020 1 O

tender for fire brigade use

80 IS 11101:1984 Specification for extended branch pipe for fire Sep 2017 S
brigade use

81 IS 11108:1984 Specification for portable fire extinguishers ― Dec 2020 4 S

Halon 1211 type

82 IS 11360:1985 Specification for smoke detectors for use in Dec 2020 S

automatic electrical fire alarm system

83 IS 11833:1986 Specification for dry powder fire extinguisher for Sep 2017 4 S
metal fires

84 IS 12717:1989 Fire fighting equipment − High capacity portable Dec 2020 1 O

pump set (1100-1600 1/min) ― Functional
requirements

85 IS 12796:1989 Fire rake ― Specification Dec 2020 S

86 IS 12805:1989 Tool McLeod for fighting forest fires ― Dec 2020 S

Specification

87 IS 12835 (Part 1):2021 Design and installation of fixed foam fire C

extinguishing system ― Code of practice:
Part 1 Low expansion foam (first revision)

88 IS 12853:1989 Fire fighting ― Pulaski tool for forest fires ― Dec 2020 S
Specification

69
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

89 IS 12859:1989 Fire fighting ― Brush hook for forest fires ― Dec 2020 S
Specification

90 IS 12861:1989 Fire fighting ― Double bit axe for forest fires ― Dec 2020 S
Specification

91 IS 12862:1989 Fire fighting ― Shovel for forest fires ― Dec 2020 S

Specification

92 *IS 13039:2014 External hydrant systems provision and Jun 2019 C

maintenance ― Code of practice (first revision)

93 IS 14851:2000 Maintenance of fire hose ― Code of practice Dec 2020 C

94 IS 14933:2001 High pressure fire fighting hose ― Specification Dec 2020 S

95 IS 14951:2001 Fire extinguisher ― 135 litres capacity Dec 2020 2 S

mechanical foam type ― Specification

96 IS 15051:2001 High pressure fire hose delivery couplings ― Sep 2017 S

Specification

97 *IS 15105:2002 Design and installation of fixed automatic Sep 2017 C

sprinkler fire extinguishing systems ― Code of
practice

98 IS 15220:2002 Halogenated hydrocarbons ― Halon 1211 and Sep 2017 S

halon 1301 ― Fire extinguishing media ―
Specification

99 IS 15221:2002 Safe handling and transfer procedures of halon Sep 2017 C

1211 and halon 1301 (halogenated hydrocarbons)
― Fire extinguishing media ― Code of practice

100 IS 15222:2002 Carbon-dioxide as fire extinguishing media for fire Sep 2017 S
protection ― Specification

101 IS 15301:2003 Installation and maintenance of fire fighting Aug 2018 C

pumps ― Specification

102 IS 15325:2020 Design and installation of fixed automatic high C

and medium velocity water spray system ― Code
of practice (first revision)

103 IS 15493:2021 Gaseous fire extinguishing systems ― General O

requirements (first revision)

104 IS 15496:2004 Inspection and maintenance of gaseous fire Jan 2020 C

extinguishing\ systems ― Code of practice

105 IS 15497:2004 Gaseous fire extinguishing systems IG 01 Jan 2020 O

extinguishing systems

106 IS 15501:2004 Gaseous fire extinguishing systems IG 541 Jan 2020 O

extinguishing

107 IS 15505:2004 Gaseous fire extinguishing systems − HCFC Jan 2020 O

Blend A extinguishing systems

70
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

108 IS 15506:2004 Gaseous fire extinguishing systems − IG 55 Jan 2020 O

extinguishing systems

109 IS 15517:2004 Gaseous fire extinguishing systems − HFC 227ea Jan 2020 2 O
(Hepta Fluoro Propane) extinguishing systems

110 IS 15519:2020 Water mist fire protection systems − System C

design, installation and commissioning ― Code of
practice (first revision)

111 IS 15525:2004 Gaseous fire extinguishing systems − IG 100 Jan 2020 O

extinguishing systems

112 IS 15528:2004 Gaseous fire extinguishing systems − Carbon Jan 2020 O

dioxide total flooding and local application (Sub-
floor and in-cabinet), high and low pressure
(refrigerated) systems

113 IS 15682:2006 Fire fighting vehicles and equipment − Symbols Feb 2017 O
for operator controls and other display

114 IS 15683:2018 Portable fire extinguishers − Performance and S

construction ― Specification (first revision)

115 IS 15811:2008 Long-range water-cum-foam monitor with self- Aug 2018 S

inducting, aspirating and non-aspirating jet and
spray/fog nozzle for fire fighting ― Specification

116 IS 15821:2008 Gaseous fire extinguishing systems − Physical Aug 2018 O

properties and system design − CF3I
Extinguishant

117 IS 15835:2009 Gaseous fire extinguishing systems ― HCFC-125 Jan 2020 1 O

Extinguishing systems

118 IS 15908:2021 Selection, installation and maintenance of control C

and indicating equipment for fire detection and
alarm system ― Code of practice (first revision)

119 IS 16018:2012 Wheeled fire extinguishers − Performance and Apr 2017 2 S

construction ― Specification

120 IS 16088:2012 Chlorinated polyvinyl chloride (CPVC) pipes for Nov 2017 S
automatic sprinkler fire extinguishing system ―
Specification

121 IS 16095:2013 Hazmat vehicle ― Specification Oct 2018 S

122 IS 16109:2013 Turntable ladder ― Specification Sep 2018 S

123 IS 16534:2017 Chlorinated polyvinyl chloride (CPVC) pipe 1 S

fittings for automatic sprinkler fire extinguishing
system ― Specification

124 IS/ISO 6182-7:2004 Fire protection ― Automatic sprinkler systems: Sep 2018 O
Part 7 Requirements and test methods for early
suppression fast response (ESFR) sprinklers

71
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

125 IS/ISO 7240-2:2003 Fire detection and alarm systems: Part 2 Control S
and indicating equipment

126 IS/ISO 7240-3:2010 Fire detection and alarm systems: Part 3 Audible S
alarm devices

127 IS/ISO 7240-4:2003 Fire detection and alarm systems: Part 4 Power S
supply equipment

128 IS/ISO 7240-5:2012 Fire detection and alarm systems: Part 5 Point- S
type heat detectors (first revision)

129 IS/ISO 7240-6:2011 Fire detection and alarm systems: Part 6 Carbon S
monoxide fire detectors using electro - chemical
cells

130 IS/ISO 7240-7:2011 Fire detection and alarm systems: Part 7 Point- Sep 2018 S
type smoke detectors using scattered light,
transmitted light or ionization

131 IS/ISO 7240-8:2014 Fire detection and alarm systems: Part 8 Point- S
type fire detectors using a carbon monoxide
sensor in combination with a heat sensor

132 IS/ISO 7240-10:2012 Fire detection and alarm systems: Part 10 Point- S
type flame detectors

133 IS/ISO 7240-11:2011 Fire detection and alarm systems: Part 11 Manual Sep 2018 S
call points

134 IS/ISO 7240-12:2014 Fire detection and alarm systems: Part 12 Line S
type smoke detectors using a transmitted optical
beam

135 IS/ISO 7240-13:2005 Fire detection and alarm systems: S

Part 13 Compatibility assessment of system
components

136 IS/ISO 7240-15:2004 Fire detection and alarm systems: Part 15 Point Sep 2018 S
type fire detectors using scattered light,
transmitted light or ionization sensor in
combination with a heat sensor

137 IS/ISO 7240-16:2007 Fire detection and alarm systems: Part 16 Sound S
system control and indicating equipment

138 IS/ISO 7240-17:2009 Fire detection and alarm systems: Part 17 Short - S
circuit isolators

139 IS/ISO 7240-18:2017 Fire detection and alarm systems: S

Part 18 Input/Output devices

140 IS/ISO 7240-20:2010 Fire detection and alarm systems: S

Part 20 Aspirating smoke detectors

141 IS/ISO 7240-21:2005 Fire detection and alarm systems: S

Part 21 Routing equipment

142 IS/ISO 7240-22:2017 Fire detection and alarm systems: S

Part 22 Smoke – Detection equipment for ducts

72
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

143 IS/ISO 7240-23:2013 Fire detection and alarm systems: Part 23 Visual S
alarm devices

144 IS/ISO 7240-24:2016 Fire detection and alarm systems: Part 24 Fire S
alarm loudspeakers

145 IS/ISO 7240-25:2010 Fire detection and alarm systems: S

Part 25 Components using radio transmission
paths

146 IS/ISO 7240-27:2018 Fire detection and alarm systems: Part 27 Point- S
type fire detectors using a smoke sensor in
combination with carbon monoxide sensor and,
optically, one or more heat sensors

147 IS/ISO 7240-29:2017 Fire detection and alarm systems: Part 29 Video S
fire detectors

DRAFT STANDARDS UNDER PUBLICATION

1 DOC:CED 22 (12086) Draft Amendment No. 2 to IS 16088:2012 Chlorinated polyvinyl chloride (CPVC)
pipes for automatic sprinkler fire extinguishing system ― Specification

2 DOC:CED 22 (14596) Draft Indian Standard Design, installation and maintenance of fixed automatic
sprinkler fire extinguishing systems — Code of Practice (first revision of IS 15105)

1 DOC:CED 22 (14938) Draft Indian Standard Automatic sprinkler heads for fire protection service
(first revision of IS 9972)

DRAFTS COMPLETED WIDE CIRCULATION

1 DOC:CED 22 (14626) Draft Indian Standard Selection, installation and maintenance of automatic fire
detection and alarm system ― Code of Practice (fifth revision of IS 2189)

DRAFT STANDARDS FORMULATED

1 DOC:CED 22 (15067) Draft Indian Standard Selection, installation and maintenance of first-aid fire
extinguishers ― Code of practice (fifth revision of IS 2190)

2 DOC:CED 22 (15715) Draft Indian Standard Hydrant systems — Design, installations and maintenance —
Code of practice (second revision of IS 13039) (amalgamating IS 3844 and
IS 9668)

3 DOC:CED 22 (16322) Draft Indian Standard Functional requirements for water tender type B for fire
brigade use (fourth revision of IS 950:2012)

4 DOC:CED 22 (16737) Draft Indian Standard Stand post type water and foam monitor for fire fighting —
Specification (second revision of IS 8442)

5 DOC:CED 22 (16738) Draft Indian Standard Revolving branch portable fixed type for fire fighting —
Specification (fourth revision of IS 906)

6 DOC:CED 22 (16739) Draft Indian Standard Low expansion foam making branch pipes and portable foam
inductors — Specification (third revision of IS 2097)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

73
CED 24 PUBLIC HEALTH ENGINEERING
SCOPE CODE OF PRACTICE FOR WATER SUPPLY, DRAINAGE AND SANITATION IN BUILDINGS,
INCLUDING LAYING OF PIPELINES, SMALL SEWAGE TREATMENT PLANTS, ANCILLARY
STRUCTURES FOR WATER SUPPLY AND SEWERAGE AND STANDARDIZATION OF
EQUIPMENT USED IN PUBLIC HEALTH ENGINEERING INCLUDING THEIR DESIGN,
MANUFACTURE, TESTING, OPERATION AND MAINTENANCE

LIAISON ISO/PC 318 (O) COMMUNITY SCALE RESOURCE ORIENTED SANITATION TREATMENT
SYSTEMS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

1 IS 1172:1993 Code of basic requirements for water supply, Nov 2017 C

drainage and sanitation (fourth revision)

2 IS 1742:1983 Code of practice for building drainage Nov 2017 C

(second revision)

3 IS 2064:1993 Selection, installation and maintenance of sanitary Nov 2017 C

appliances ― Code of practice (second revision)

4 IS 2065:1983 Code of practice for water supply in buildings Feb 2017 C

(second revision)

5 IS 2470 (Part 1):1985 Code of practice for installation of septic tanks: Feb 2017 C
Part 1 Design criteria and construction
(second revision)

6 IS 2470 (Part 2):1985 Code of practice for installation of septic tanks: Feb 2017 2 C
Part 2 Secondary treatment and disposal of septic
tank effluent

7 IS 3114:1994 Code of practice for laying of cast iron pipes Aug 2019 C
(second revision)

8 IS 4111 (Part 1):1986 Code of practice for ancillary structures in sewerage Feb 2017 C
system: Part 1 Manholes (first revision)

9 IS 4111 (Part 2):1985 Code of practice for ancillary structures in sewerage Feb 2017 C
system: Part 2 Flushing tanks (first revision)

10 IS 4111 (Part 3):1985 Code of practice for ancillary structures in sewerage Feb 2017 C
system: Part 3 Inverted syphon (first revision)

11 IS 4111 (Part 4):1968 Code of practice for ancillary structures in sewerage Feb 2017 C
system: Part 4 Pumping stations and pumping mains
(rising mains)

12 IS 4111 (Part 5):1993 Code of practice for ancillary structures in sewerage Aug 2019 C
system: Part 5 Tidal outfalls

13 IS 4127:1983 Code of practice for laying of glazed stoneware Feb 2017 C

pipes (first revision)

14 IS 5329:1983 Code of practice for sanitary pipe work above Feb 2017 C
ground for buildings (first revision)

74
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

15 IS 5611:1987 Code of practice for construction of waste Nov 2017 C

stabilization ponds (faculative type) (first revision)

16 IS 5822:1994 Code of practice for laying of electrically welded Aug 2019 C

steel pipes for water supply (second revision)

17 IS 6279:1971 Specification for equipment for grit removal devices Feb 2021 S

18 IS 6280:1971 Specification for sewage screens Feb 2021 S

19 IS 6295:1986 Code of practice for water supply and drainage in Feb 2017 C
high altitudes and/or sub-zero temperature regions
(first revision)

20 IS 6924:1973 Code of practice for the construction of refuse Feb 2017 C

chutes in multistoreyed buildings

21 IS 7090:1985 Guidelines for rapid mixing devices (first revision) Feb 2021 C

22 IS 7208:1992 Flocculator devices ― Code of practice Feb 2017 C

(first revision)

23 IS 7232:1974 Method for imhoff cone test Nov 2017 M

24 IS 7558:1974 Code of practice for domestic hot water installations Feb 2017 C

25 IS 7740:1985 Code of practice for construction and maintenance Feb 2017 C

of road gullies (first revision)

26 IS 8413 (Part 1):1977 Requirements for biological treatment equipment: Feb 2021 S
Part 1 Trickling filters

27 IS 8413 (Part 2):1982 Requirements for biological treatment and Feb 2021 S
equipment: Part 2 Activated sludge process and its
modifications

28 IS 8419 (Part 1):1977 Requirements for filtration equipment: Feb 2021 1 S

Part 1 Filtration media - sand and gravel

29 IS 8419 (Part 2):1984 Requirements for rapid sand gravity filtration Feb 2021 S
equipment: Part 2 Underdrainage system

30 IS 9110:1979 Specification for hand operated augers for cleaning Feb 2021 S
water-closets, pipes and sewers

31 IS 9222 (Part 1):1990 Recommendations for handling and dosing devices Feb 2021 C
for chemicals for water treatment: Part 1 Coagulants
(first revision)

32 IS 10037 (Part 1):1981 Requirements for sludge dewatering equipment: Nov 2017 S
Part 1 Sludge drying beds-sand, gravel and
underdrains

33 IS 10037 (Part 2):1983 Requirements for sludge de-watering equipment: Feb 2021 S
Part 2 Vacuum filtration equipment

34 IS 10037 (Part 3):1983 Requirements for sludge de-watering equipment: Feb 2021 S
Part 3 Centrifugal equipment (Solid bowl type)

75
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

35 IS 10053:1981 Requirements for equipment for jackson candle Nov 2017 S

turbidi meter and determination of turbidity

36 IS 10261:1982 Requirements for settling tank (clarifier equipment) Feb 2021 S

for waste water treatment

37 IS 10313:1982 Requirements for settling tank (clarifier equipment) Feb 2021 S

for water treatment plant

38 IS 10446:1983 Glossary of terms relating to water supply and Feb 2017 T

sanitation

39 IS 10552:1983 Specification for buckets to be used in power driven Feb 2021 S

bucket type sewer cleaning machine

40 IS 10553 (Part 1):1983 Requirements for chlorination equipment: Nov 2017 1 C

Part 1 General guidelines for chlorination plants
including handling, storage and safety of chlorine
cylinders and drums

41 IS 10553 (Part 2):1983 Requirements for chlorination equipment: Feb 2021 S

Part 2 Vacuum feed type chlorinators

42 IS 10553 (Part 4):1983 Requirements for chlorination equipment: Feb 2021 S

Part 4 Gravity feed type gaseous chlorinators

43 IS 10553 (Part 5):1987 Requirements of chlorination equipment: Nov 2017 S

Part 5 Bleaching powder solution feeder
displacement type chlorinator

44 IS 10595:1983 Requirements for power driven bucket type sewer Feb 2021 S
cleaning machine

45 IS 11117:1984 Requirements for power driven rodding machine for Feb 2021 S
sewers

46 IS 11208:1985 Guidelines for registration of plumbers Feb 2017 C

47 IS 11387:1985 Requirements for high pressure jetting machine for Feb 2021 S
sewer cleaning

48 IS 11397:1985 Specification for attachment tools for power driven Feb 2021 S
rodding machine for sewers

49 IS 11401 (Part 1):1985 Requirements for slow sand filters: Part 1 General Nov 2017 C
guidelines

50 IS 11401 (Part 2):1990 General requirements for slow sand filters: Aug 2019 1 C
Part 2 Design, construction, operation and
maintenance

51 IS 11906:1986 Recommendations for cement mortar lining for cast Nov 2017 C
iron mild steel and ductile-iron pipes and fittings for
transportation of water

52 IS 11925:1986 Specification for pitch impregnated fibre pipes and Nov 2017 S
fittings for drainage purposes

76
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

53 IS 11931:1987 Specification for sewer cleaning metal rods Nov 2017 S

54 IS 11972:1987 Code of practice for safety precautions to be taken Nov 2017 C

when entering a sewerage system

55 IS 12183 (Part 1):1987 Code of practice for plumbing in multi-storeyed Aug 2019 C
buildings: Part 1 Water supply

56 IS 12251:1987 Code of practice for drainage of building basements Aug 2019 C

57 IS 12288:1987 Code of practice for use and laying of ductile iron Nov 2017 1 C
pipes

58 IS 12314:1987 Code of practice for sanitation with leaching pits for Nov 2017 C
rural communities

59 IS 13166:1992 Mechanical surface aerators ― Guidelines for Feb 2017 C

evaluation and testing

60 IS 13496:1992 General requirements of suction machine for Nov 2017 S

cleaning sewers, manholes and ancillary structures
provided on sewer line and closed storm water
drains

61 SP 35 (S&T):1987 Handbook on water supply and drainage with O

special emphasis on plumbing

DRAFTS COMPLETED WIDE CIRCULATION

1 DOC:CED 24 (15672) Amendment No. 1 to IS 5822:1994

DRAFT STANDARDS FORMULATED

1 DOC:CED 24 (16883) Draft Indian Standard Rotationally moulded polyethylene septic tank

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

77
CED 29 CONSTRUCTION MANAGEMENT (INCLUDING SAFETY IN CONSTRUCTION)
SCOPE FORMULATION OF STANDARDS IN THE FIELD OF CONSTRUCTION MANAGEMENT AND
RELATED ASPECTS. FORMULATION OF STANDARDS LAYING DOWN SAFETY REQUIREMENTS
IN THE VARIOUS OPERATIONS INVOLVED IN DIFFERENT TYPES OF CIVIL ENGINEERING
CONSTRUCTION.

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 3696 (Part 1):1987 Safety code of scaffolds and ladders: Mar 2017 SS
Part 1 Scaffolds (first revision)

2 IS 3696 (Part 2):1991 Scaffolds and ladders ― Code of Safety: Mar 2017 SS
Part 2 Ladders (first revision)

3 IS 3764:1992 Excavation work ― Code of safety (first revision) Mar 2017 SS

4 IS 4014 (Part 2):2013 Steel tubular scaffolding ― Code of practice: Dec 2018 SS
Part 2 Safety provisions for scaffolding
(first revision)

5 IS 4081:2013 Blasting and related drilling operations ― Code of Dec 2018 SS

safety (second revision)

6 IS 4082:1996 Stacking and storage of construction materials and May 2018 C

components at site ― Recommendations
(second revision)

7 IS 4130:1991 Demolition of buildings ― Code of safety Mar 2017 SS

(second revision)

8 IS 4138:1977 Safety code for working in compressed air Mar 2017 SS

(first revision)

9 IS 4756:1978 Safety code for tunneling work (first revision) Mar 2017 SS

10 IS 4912:1978 Safety requirements for floor and wall openings, Mar 2017 SS
railings and toe boards (first revision)

11 IS 5121:2013 Piling and other deep foundations ― Code of Dec 2018 SS

safety (first revision)

12 IS 5916:2013 Construction involving use of hot bituminous Dec 2018 SS

materials ― Code of safety (first revision)

13 IS 7272 (Part 1):1974 Recommendation for labour output constants for Apr 2020 1 O
building work: Part 1 North zone

14 IS 7293:1974 Safety code for working with construction Mar 2017 SS

machinery

15 IS 7969:1975 Safety code for handling and storage of building Mar 2017 1 SS
materials

16 IS 8989:1978 Safety code for erection of concrete framed Apr 2020 SS

structures

78
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

17 IS 10067:1982 Material constants in building works Apr 2020 O

18 IS 10291:1982 Safety code for dress divers in civil engineering Mar 2017 SS
works

19 IS 10302:1982 Unified nomenclature of workmen for civil Apr 2020 SS

engineering

20 IS 13415:1992 Protective barriers in and around buildings ― Code Mar 2017 SS

of safety

21 IS 13416 (Part 1):1992 Preventive measures against hazards at Mar 2017 C

workplaces ― Recommendations: Part 1 Falling
material hazards prevention

22 IS 13416 (Part 2):1992 Preventive measures against hazards at Mar 2017 C

workplaces ― Recommendations: Part 2 Fall
prevention

23 IS 13416 (Part 3):1994 Preventive measures against hazards at May 2018 C

workplaces ― Recommendations: Part 3 Disposal
of debris

24 IS 13416 (Part 4):1994 Preventive measures against hazards at May 2018 C

workplaces ― Recommendations: Part 4 Timber
structures

25 IS 13416 (Part 5):1994 Preventive measures against hazards at Mar 2017 C

workplaces ― Recommendations: Part 5 Fire
protection

26 IS 13430:1992 Safety during additional construction and alteration Mar 2017 C

to existing buildings ― Code of practice

27 IS 15883 (Part 1):2009 Construction project management ― Guidelines: Jun 2019 C

Part 1 General

28 IS 15883 (Part 2):2013 Construction project management ― Guidelines: Feb 2018 C

Part 2 Time management

29 IS 15883 (Part 3):2015 Construction project management ― Guidelines: Dec 2020 C

Part 3 Cost management

30 IS 15883 (Part 4):2015 Construction project management ― Guidelines: Nov 2020 C

Part 4 Quality management

31 IS 15883 (Part 5):2013 Construction project management ― Guidelines: Dec 2018 C

Part 5 Health and safety management

32 IS 15883 (Part 6):2015 Construction project management ― Guidelines: Nov 2020 C

Part 6 Scope management

33 IS 15883 (Part 7):2021 Construction project management  Guidelines: C

Part 7 Procurement management

34 IS 15883 (Part 8):2015 Construction project management ― Guidelines: Sep 2020 C

Part 8 Risk management

79
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

35 IS 15883 (Part 9):2018 Construction project management ― Guidelines: C

Part 9 Communication management

36 IS 15883 (Part 10):2021 Construction project management  Guidelines: C

Part 10 Human resource management

37 IS 15883 (Part 11):2021 Construction project management  Guidelines: C

Part 11 Sustainability management
38 IS 15883 (Part 12):2016 Construction project management ― Guidelines: C
Part 12 Integration management

39 IS 16416:2016 Construction project management ― Guidelines: C

Project formulation and appraisal

40 IS 16601:2016 Habitat and welfare requirements for construction C

workers ― Guidelines

41 SP 70:2001 Handbook on construction safety practices O

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

80
CED 30 CLAY AND STABILIZED SOIL PRODUCTS FOR CONSTRUCTION
SCOPE STANDARDIZATION IN THE FIELD OF BURNT, UNBURNT CLAY AND STABILIZED SOIL
PRODUCTS FOR CONSTRUCTION

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 654:1992 Clay roofing tiles, mangalore pattern ― Sep 2016 S

Specification (third revision)

2 IS 1077:1992 Common burnt clay building bricks ― Sep 2016 1 S

Specification (fifth revision)

3 IS 1464:1992 Clay ridge and ceiling tiles ― Specification Sep 2016 S

(second revision)

4 IS 1478:1992 Clay flooring tile ― Specification Sep 2016 S

(second revision)

5 IS 1725:2013 Stabilized soil blocks used in general building Oct 2018 S

construction ― Specification (second revision)

6 IS 2117:1991 Guide for manufacture of hand-made common Sep 2016 C

burnt clay building bricks (third revision)

7 IS 2180:1988 Specification for heavy duty burnt clay building Sep 2016 S
bricks (third revision)

8 IS 2222:1991 Specification for burnt clay perforated building Sep 2016 3 S

bricks (fourth revision)

9 IS 2248:1992 Glossary of terms relating to clay products for Sep 2016 1 T

buildings (second revision)

10 IS 2690 (Part 1):1993 Burnt clay flat terracing tiles ― Specification: Sep 2016 S
Part 1 Machine made (second revision)

11 IS 2690 (Part 2):1992 Burnt clay flat terracing tiles ― Specification: Sep 2016 1 S
Part 2 Hand made (second revision)

12 IS 2691:2017 Burnt clay facing bricks ― Specification S

(third revision)

13 IS 3367:1993 Burnt clay tiles for use in lining irrigation and Sep 2016 S
drainage works ― Specification (second revision)

14 IS 3495 (Parts 1):2019 Burnt clay building bricks ― Methods of tests: M

Part 1 Determination of compressive strength
(fourth revision)

15 IS 3495 (Parts 2):2019 Burnt clay building bricks ― Methods of tests: M

Part 2 Determination of water absorption
(fourth revision)

16 IS 3495 (Parts 3):2019 Burnt clay building bricks ― Methods of tests: M

Part 3 Determination of efflorescence
(fourth revision)

17 IS 3495 (Parts 4):2019 Burnt clay building bricks ― Methods of tests: M

Part 4 Determination of warpage (fourth revision)

81
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

18 IS 3583:1988 Specification for burnt clay paving bricks Feb 2020 S

IS 3583:1988 (B) (second revision)
IS 3583:1988 (H)
19 IS 3951 (Part 1):2009 Hollow clay tiles for floors and roofs ― Feb 2020 S
Specification: Part 1 Filler type
20 IS 3951 (Part 2):2009 Hollow clay tiles for floors and roofs ― Feb 2020 S
Specification: Part 2 Structural type
(second revision)
21 IS 3952:2013 Specification for burnt clay hollow bricks and Dec 2018 S
blocks for walls and partitions (third revision)
22 IS 3978:1993 Manufacture of burnt clay Mangalore pattern Sep 2016 C
roofing tiles ― Code of practice (first revision)
23 IS 4885:1988 Specification for sewer bricks (first revision) Feb 2020 S
24 IS 5454:1978 Methods of sampling of clay building bricks Feb 2020 1 M
(first revision)
25 IS 5779:1986 Specification for burnt clay soling bricks Sep 2016 S
(first revision)
26 IS 6165:1992 Dimensions for special shapes of clay bricks Sep 2016 O
(first revision)
27 IS 7556:1988 Specification for burnt clay jallies (first revision) Feb 2020 S
28 IS 8920:1978 Methods for sampling of burnt clay tiles Jul 2018 M
29 IS 11650:1991 Guide for manufacture of common burnt clay Sep 2016 C
building bricks by semi-mechanized process
(first revision)
30 IS 13317:1992 Specification for clay roofing country tiles, half Sep 2016 S
round and flat tiles
31 IS 13757:1993 Specification for burnt clay fly ash building bricks Sep 2016 2 S
32 IS 17057:2019 Construction of bull’s trench brick kiln — C
Guidelines

33 IS 17058:2019 Glossary of terms relating to brick kilns T

34 IS 17059:2019 Construction of zig zag brick kiln — Guidelines C

35 IS 17165:2020 Manufacture of stabilized soil blocks — C

Guidelines

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 30 (15751) Draft Indian Standard Burnt clay building bricks – Method of test:
Part 5 Determination of initial rate of absorption [IS 3495 (Part 5)]

2 DOC:CED 30 (15752) Draft Indian Standard Burnt clay building bricks – Method of test:
Part 6 Determination of modulus of rupture [IS 3495 (Part 6)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

82
CED 35 FURNITURE
SCOPE STANDARDIZATION IN THE FIELD OF FURNITURE INCLUDING FURNITURE USED FOR
GENERAL PURPOSES, OFFICES, SCHOOLS, STADIUM, AUDITORIUM, CINEMA HOUSES,
RESTAURANTS, LIBRARY, ETC

LIAISON ISO/TC 136 (O) FURNITURE

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1829 (Part 1):2017 Library furniture and fittings ― Specification: S

Part 1 Timber (second revision)

2 IS 1829 (Part 2):2017 Library furniture and fittings: Part 2 Steel ― S

Specification (second revision)

3 IS 1883:2020 Metal shelving racks (adjustable type) ― S

Specification (fourth revision)

4 IS 2695:1993 Specification for drawing filing equipment Sep 2017 S

(second revision)

5 IS 3312:2021 Steel shelving cabinets (adjustable type) ― S

Specification (third revision)

6 IS 3313:1983 Specification for steel filing cabinets for general May 2020 S
office purposes (second revision)

7 IS 3314:1984 Specification for steel clothes lockers May 2020 S

(second revision)

8 IS 3497:1992 Steel wardrobes (adjustable type) ― Sep 2017 S

Specification (second revision)

9 IS 3498:1993 Metal table (office type) ― Specification Sep 2017 S

(third revision)

10 IS 3499 (Part 1):1985 Specification for metal chairs for office purposes: May 2020 S
Part 1 Non-revolving and non-tilting
(second revision)

11 IS 3499 (Part 2):1985 Specification for metal chairs for office purposes: May 2020 S
IS 3499 (Part 2):1985(B) Part 2 Revolving and tilting (second revision)

12 IS 3663:2018 Dimensions of tables and chairs for office D

purposes (third revision)

13 IS 3761:2020 Metal side racks (adjustable type) ― S

Specification (second revision)

14 IS 3762:1979 Specification for metal waste paper bins May 2020 S

(first revision)

15 IS 3763:1983 Specification for metal folding chairs May 2020 S

(first revision)

83
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

16 IS 3791:1983 Specification for metal paper trays (first revision) May 2020 S

17 IS 3845:1966 Code of practice for joints used in wooden May 2020 C

furniture

18 IS 4103:1977 Specification for metal nesting chairs May 2020 1 S

(first revision)

19 IS 4116:1988 Specification for wooden shelving cabinets Sep 2017 2 S

(adjustable type) (second revision)

20 IS 4126:1986 Specification for wooden wardrobes (adjustable May 2020 2 S

and non- adjustable type) (first revision)

21 IS 4204:1974 Functional requirements for drafting chairs May 2020 1 S

(first revision)

22 IS 4205:1989 Drafting stools ― Specification (second revision) Sep 2017 S

23 IS 4414:1990 Wooden table tops ― Specification Sep 2017 2 S

(second revision)

24 IS 4415:1974 Glossary of terms relating to wooden furniture Sep 2017 1 T

and fixtures (first revision)

25 IS 4837:1990 School furniture, classroom chairs and tables ― Sep 2017 1 C

IS 4837:1990 (B) Recommendations (second revision)

26 IS 5391:1992 Adjustable metal chairs for use of typists and May 2020 S
operators in telephone exchanges ―
Specification (second revision)

27 IS 5416 (Part 1):1988 Methods of test for strength and stability of Sep 2017 M
chairs and stools: Part 1 Strength (first revision)

28 IS 5416 (Part 2):1988 Method of test for strength and stability of chairs Sep 2017 M
and stools: Part 2 Determination of stability of
chairs and stools (first revision)

29 IS 5807 (Part 1):1975 Methods of test for clear finishes for wooden Sep 2017 M
furniture: Part 1 Resistance to dry heat
(first revision)

30 IS 5807 (Part 2):1975 Methods of test for clear finishes for wooden Sep 2017 M
furniture: Part 2 Resistance to wet heat
(first revision)

31 IS 5807 (Part 3):1971 Methods of test for clear finishes for wooden Sep 2017 M
furniture: Part 3 Resistance to marking by oils
and fats

32 IS 5807 (Part 4):1975 Methods of test for clear finishes for wooden Sep 2017 M
furniture: Part 4 Resistance to marking by liquids

33 IS 5807 (Part 5):1975 Methods of test for clear finishes for wooden Sep 2017 M
furniture: Part 5 Test for low-angle glare

84
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

34 IS 5807 (Part 6):1978 Methods of test for clear finishes for wooden Sep 2017 M
furniture: Part 6 Resistance to mechanical
damage

35 IS 5823:1986 Specification for dining tables (first revision) May 2020 2 S

36 IS 5923:1986 Specification for wooden clothes lockers May 2020 2 S

(first revision)

37 IS 5967 (Part 1):1988 Methods of test for strength and stability of Sep 2017 M
tables and trolleys: Part 1 Strength
(first revision)

38 IS 5967 (Part 2):1988 Methods of test for strength and stability of Sep 2017 M
tables and trolleys: Part 2 Stability (first revision)

39 IS 5974:1986 Specification for divans and easy chairs May 2020 2 S

(first revision)

40 IS 6179:1971 Specification and safety requirements for rigid May 2020 3 S

sided playpens

41 IS 6184:1971 Dimensions for furniture mirrors Sep 2017 D

42 IS 6185:1971 Specification and safety requirements for high May 2020 S

chairs

43 IS 6188:1988 Specification for wooden bedside table Sep 2017 2 S

(first revision)

44 IS 6189:1985 Specification for metal stationary cupboards May 2020 S

(first revision)

45 IS 6632:1988 Specification for wooden folding chairs Sep 2017 2 S

(first revision)

46 IS 7070:1988 Wooden shelving racks, adjustable and non- Sep 2017 2 S

adjustable type ― Specification (first revision)

47 IS 7076:1983 Specification for metal book ends (first revision) May 2020 S

48 IS 7259 (Part 1):1988 Specification for wooden beds: Part 1 For use May 2020 2 S
with mattresses (first revision)

49 IS 7760:1985 Specification for steel glass-front cabinets May 2020 S

(first revision)

50 IS 7761:1983 Specification for steel book cases (first revision) May 2020 S

51 IS 8126:1993 Specification for composite office tables Sep 2017 S

(first revision)

52 IS 8467:1977 Specification for steel card-index cabinets May 2020 1 S

53 IS 8761:1978 Specification for steel folding cots May 2020 S

54 IS 9236:1993 Metal letter-rests ─ Specification (first revision) Sep 2017 S

85
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

55 IS 9715:1981 Specification for steel visible indexing system May 2020 S

cabinets

56 IS 11525:1986 Specification for wooden chairs for office May 2020 2 S

purposes

57 IS 11679:1986 Specification for wooden tables for office use May 2020 2 S

58 IS 12674 (Part 1):1989 Methods of test for strength and stability of Sep 2017 M
settees and benches: Part 1 Strength

59 IS 12674 (Part 2):1989 Methods of test for strength and stability of Sep 2017 M
settees and Benches: Part 2 Stability

60 IS 12680:1989 Wooden sofa-cum-bed ― Specification Sep 2017 2 S

61 IS 13089:1991 Furniture ― Storage units ― Determination of May 2020 M

/ ISO 7171-1988 stability

62 IS 13713:2021 Plastic chairs for general purposes ― S

Specification (first revision)

63 IS 13896:1994 Machine operators table and visual display unit Apr 2019 S
(VDU) table ― Specification

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 35 (16969) Draft Indian Standard Work chairs ― Specification

2 DOC:CED 35 (16970) Draft Indian Standard General purpose chairs and stools ― Specification

3 DOC:CED 35 (16971) Draft Indian Standard Tables and desks ― Specification

4 DOC:CED 35 (16972) Draft Indian Standard Storage units ― Specification

5 DOC:CED 35 (16973) Draft Indian Standard Beds ― Specification

6 DOC:CED 35 (16974) Draft Indian Standard Bunk beds ― Specification

7 DOC:CED 35 (16975) Draft Indian Standard Performance requirements of surface finishes for furniture
applications

8 DOC:CED 35 (16976) Draft Indian Standard Assessment of surface finish resistance to dry heat ―
Method of test

9 DOC:CED 35 (16977) Draft Indian Standard Assessment of surface finish resistance to wet heat ―
Method of test

10 DOC:CED 35 (16978) Draft Indian Standard Assessment of surface finish resistance to cold liquids ―
Method of test

11 DOC:CED 35 (16979) Draft Indian Standard Assessment of surface finish resistance to impact ― Method
of test

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

86
CED 36 FIRE SAFETY
SCOPE STANDARDIZATION IN THE FIELD OF FIRE SAFETY; FIRE PRECAUTIONS, FIRE RESISTANCE
OF BUILDING MATERIALS, BUILDING COMPONENTS STRUCTURES AND TESTS CONNECTED
THEREWITH

LIAISON ISO/TC 92 (O) FIRE SAFETY

ISO/TC 92/SC 1 (O) FIRE INITIATION AND GROWTH
ISO/TC 92/SC 2 (O) FIRE CONTAIMENT
ISO/TC 92/SC 3 (O) FIRE THREAT TO PEOPLE AND ENVIRONMENT

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1641:2013 Fire safety of buildings (general) ― Code of Jul 2018 C

practice: General principles of fire grading and
classification (second revision)

2 IS 1642:2013 Fire safety of buildings (general) ― Code of Jul 2018 C

practice: Details of construction (second revision)

3 IS 1643:2013 Fire safety of buildings (general) ― Code of Aug 2018 C

practice: Exposure hazard (second revision)

4 IS 1644:2013 Fire safety of buildings (general) ― Code of Aug 2018 C

practice: Exit requirements and personal hazard
(second revision)

5 IS 1646:2015 Code of practice for fire safety of buildings (general): Dec 2020 C
Electrical installations (third revision)

6 IS 2726:1988 Code of practice for fire safety of industrial buildings: Sep 2017 C
Cotton ginning and pressing (including cotton seed
delintering) factories (first revision)

7 IS 3034:1993 Fire safety of industrial buildings ― Code of Sep 2017 1 C

practice: Electrical generating and distributing
stations (second revision)

8 IS 3058:1990 Code of practice for fire safety of industrial buildings: Mar 2021 C
Viscose rayon yarn and/or staple fibre plants
(first revision)

9 IS 3079:1990 Code of practice for fire safety of industrial buildings: Mar 2021 C
Cotton textile mills (first revision)

10 IS 3594:1991 Code of practice for fire safety of industrial buildings: Mar 2021 C
General storage and warehousing including cold
storages (first revision)

11 IS 3595:2002 Code of practice for fire safety of industrial buildings: Sep 2017 C
Coal pulverizers and associated equipment
(second revision)

12 *IS 3614 (Part 1): Specification for fire-check doors: Part 1 Plate, metal Sep 2017 S
1966 covered and rolling

87
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

13 *IS 3614 (Part 2): Metallic and non-metallic fire check doors ― Sep 2017 S
1992 Resistance test and performance criteria

14 IS 3808:1979 Method of test for non-combustibility of building Mar 2021 M

materials (first revision)

15 IS 3809:1979 Fire resistance test for structures (first revision) Sep 2017 O

16 IS 3836:2000 Fire safety of industrial buildings ― Jute mills ― Mar 2021 C

Code of practice (second revision)

17 IS 4226:1988 Code of practice for fire safety of industrial buildings: Sep 2017 C
Aluminium/Magnesium powder factories
(first revision)

18 IS 4886:1991 Fire safety of industrial buildings: Tea factories ― Mar 2021 1 C

Code of practice (first revision)

19 IS 6329:2000 Code of practice for fire safety of industrial buildings Mar 2021 C
− Saw mills and wood works (first revision)

20 *IS 8757:1999 Glossary of terms associated with fire safety Mar 2021 T
(first revision)

21 IS 8758:2013 Fire precautionary measures in construction of May 2018 C

temporary structures and pandals ― Code of
practice (second revision)

22 IS 9109:2000 Fire safety of industrial buildings ― Paint and Mar 2021 C

varnish factories ― Code of practice (first revision)

23 IS 11457 (Part 1): Code of practice for fire safety of chemical Mar 2021 C
1985 industries: Part 1 Rubber and plastic

24 IS 11460:1985 Code of practice for fire safety of libraries and Mar 2021 1 C
archives

25 IS 12349:1988 Fire protection-safety signs Sep 2017 O

26 IS 12407:1988 Graphic symbols for fire protection plans Sep 2017 O

27 IS 12456:2004 Fire protection of electronic data processing Jan 2020 C

installation ― Code of practice (first revision)

28 IS 12458:2019 Fire resistance of through penetration firestops — M

Method of Test (first revision)

29 IS 12459:1988 Code of practice for fire safety in cable runs Sep 2017 1 C

30 IS 12777:1989 Method for classification of flame spread of products Mar 2021 M

31 IS 13045:1991 Code of practice for fire safety of industrial buildings Mar 2021 C
− Flour mills

32 IS 13694:1993 Fire safety in iron and steel industries ― Code of Sep 2017 1 C
practice

88
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

33 IS 13716:1993 Code of practice for fire safety in hotels Sep 2017 1 C

34 IS 14435:2013 Fire safety in educational institutions ― Code of Sep 2018 C

practice (first revision)

35 IS 14689:1999 Code of practice for fire safety in industrial buildings Jan 2020 C
(printing and publishing industry)

36 IS 14850:2000 Fire safety of museums ― Code of practice Mar 2021 C

37 IS 15381:2021 Fire blanket ― Specification (first revision) S

38 IS 15394:2003 Fire safety in petroleum refineries and fertilizer Sep 2018 C

plants ― Code of practice

39 IS/ISO 834-1:1999 Fire-resistance tests – Elements of building Oct 2019 M

construction: Part 1 General requirements

40 IS/ISO 834-4:2000 Fire-resistance tests – Elements of building Oct 2019 M

construction: Part 4 Specific requirements for load
bearing vertical separating elements

41 IS/ISO 834-5:2000 Fire-resistance tests – Elements of building Oct 2019 M

construction: Part 5 Specific requirements for load
bearing horizontal separating elements

42 IS/ISO 834-6:2000 Fire-resistance tests – Elements of building M

construction: Part 6 Specific requirements for
beams

43 IS/ISO 834-7:2000 Fire-resistance tests – Elements of building M

construction: Part 7 Specific requirements for
columns

44 IS/ISO 834-8:2002 Fire-resistance tests – Elements of building M

construction: Part 8 Specific requirements for non-
load bearing vertical separating elements

45 IS/ISO 834-9:2003 Fire-resistance tests – Elements of building M

construction: Part 9 Specific requirements for non-
load bearing ceiling elements

46 IS/ISO 3009:2003 Fire-resistance tests ‒ Elements of building M

construction ‒ Glazed elements

47 IS/ISO 19706:2011 Guidelines for assessing the fire threat to people Dec 2020 O

48 IS/ISO 21927-1:2008 Smoke and heat control systems – S

Part 1: Specification for smoke barriers

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 36 (13652) Draft Indian Standard Specification for fire doors and doorsets [first revision of
IS 3614 (Part 1 & 2)]

2 DOC:CED 36 (16042) Draft Indian Standard Glossary of Terms Associated With Fire Safety
(second revision of IS 8757)

89
 DRAFT STANDARDS FORMULATED

1 DOC:CED 36 (15755) Draft Indian Standard Fire safety in commercial kitchen — Guidelines

2 DOC:CED 36 (15775) Draft Indian Standard Fire resistance of perimeter fire barrier joint system —
Method of test

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

90
CED 37 STRUCTURAL SAFETY
SCOPE STANDARDIZATION IN THE FIELD OF STRUCTURAL SAFETY INCLUDING LOADING
STANDARDS

LIAISON ISO/TC 98 (P) BASES FOR DESIGN OF STRUCTURES

ISO/TC 98/SC 1 (P) TERMINOLOGY AND SYMBOLS
ISO/TC 98/SC 2 (P) RELIABILITY OF STRUCTURES
ISO/TC 98/SC 3 (P) LOADS, FORCES AND OTHER ACTIONS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 875 (Part 1):1987 Code of practice for design loads (other than May 2018 1 C
earthquake) for buildings and structures:
Part 1 Dead loads − Unit weights of building
material and stored materials (second revision)
(Incorporating IS:1911-1967)

2 IS 875 (Part 2):1987 Code of practice for design loads (other than May 2018 1 C
earthquake) for buildings and structures:
Part 2 Imposed loads (second revision)

3 IS 875 (Part 3):2015 Design loads (other than earthquake) for buildings Apr 2020 2 C
and structures ― Code of practice: Part 3 Wind
loads (third revision)

4 *IS 875 (Part 4):1987 Code of practice for design loads (other than May 2018 C
earthquake) for buildings and structures:
Part 4 Snow loads (second revision)

5 IS 875 (Part 5):1987 Code of practice for design loads (other than May 2018 1 C
earthquake) for buildings and structures:
Part 5 Special loads and load combinations
(second revision)

6 SP 64 (S&T):2001 Explanatory Handbook on Indian Standard Code O

of practice for design loads (other than
earthquake) for buildings and structures:
Part 3 Wind loads [IS 875 (Part 3):1987]

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 37 (16040) Draft Indian Standard Design loads (other than earthquake) for buildings and
structures – Code of practice: Part 4 Snow load [third revision of IS 875 (Part 4)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

91
CED 38 SPECIAL STRUCTURES
SCOPE STANDARDIZATION IN THE FIELD OF DESIGN OF SPECIALSTRUCTURES SUCH AS CHIMNEYS,
BINS AND SILOS, SHELL STRUCTURES, OVERHEAD WATER TANKS, COOLING TOWERS,
SPACESTRUCTURES, COMPOSITE CONSTRUCTION, ETC, CONSISTING OF REINFORCED AND
PRESTRESSED CONCRETE, HANDBOOKS RELATING TO SPECIAL STRUCTURES

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 2210:1988 Criteria for design of reinforced concrete shell Apr 2017 C

structures and folded plates (first revision)

2 IS 3935:1966 Code of practice for composite construction Apr 2017 C

3 IS 4090:1967 Criteria for the design of reinforced concrete Apr 2017 C

arches

4 IS 4995 (Part 1):1974 Criteria for design of reinforced concrete bins for Apr 2017 1 C
the storage of granular and powdery materials:
Part 1 General requirements and assessment of
bin loads (first revision)

5 IS 4995 (Part 2):1974 Criteria for design of reinforced concrete bins for Apr 2017 1 C
storage of granular and powdery materials:
Part 2 Design criteria (first revision)

6 IS 4998:2015 Design of reinforced concrete chimneys ― Dec 2020 C

Criteria (third revision)

7 *IS 11384:1985 Code of practice for composite construction in Apr 2017 C

structural steel and concrete

8 IS 11504:2020 Criteria for structural design of reinforced concrete C

natural draught cooling towers (first revision)

9 IS 11682:1985 Criteria for design of RCC staging for overhead Apr 2017 C
water tanks

10 IS 16700:2017 Criteria for structural safety of tall concrete 1 SS

buildings

11 SP 43 (S&T):1987 Handbook on structures with reinforced concrete O

portal frames (without cranes)

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 38 (13455) Composite construction in structural steel and concrete ― Code of practice
(first revision of IS 11384)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

92
CED 39 EARTHQUAKE ENGINEERING
SCOPE STANDARDIZATION IN THE FIELD OF DESIGN AND CONSTRUCTION OF EARTHQUAKE
RESISTANT STRUCTURES AND IN THE FIELD OF INSTRUMENTS AND TESTS CONNECTED
THEREWITH

LIAISON ISO/TC 98 (P) BASES FOR DESIGN OF STRUCTURES

ISO/TC 98/SC 1 (P) TERMINOLOGY AND SYMBOLS
ISO/TC 98/SC 2 (P) RELIABILITY OF STRUCTURES
ISO/TC 98/SC 3 (P) LOADS, FORCES AND OTHER ACTIONS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1893:1984 Criteria for earthquake resistant design of structures Jul 2018 C

(fourth revision)

2 IS 1893 (Part 1):2016 Criteria for earthquake resistant design of 2 C

structures: Part 1 General provisions and buildings
(sixth revision)

3 IS 1893 (Part 2):2014 Criteria for earthquake resistant design of Aug 2019 C
structures: Part 2 Liquid retaining tanks
(fifth revision)

4 IS 1893 (Part 3):2014 Criteria for earthquake resistant design of Aug 2019 C
structures: Part 3 Bridges and retaining walls

5 IS 1893 (Part 4):2015 Criteria for earthquake resistant design of May 2020 2 C
structures: Part 4 Industrial structures including
stack-like structures (first revision)

6 IS 4326:2013 Earthquake resistant design and construction of Jul 2018 1 C

buildings ― Code of practice (third revision)

7 IS 4967:1968 Recommendations for seismic instrumentation for May 2020 C

river valley projects

8 IS 4991:1968 Criteria for blast resistant design of structures for Jul 2018 C
explosions above ground

9 IS 6922:1973 Criteria for safety and design of structures subject to Jul 2018 C
underground blasts

10 IS 13827:1993 Improving earthquake resistance of earthen Jul 2018 2 C

buildings ― Guidelines

11 IS 13828:1993 Improving earthquake resistance of low strength Jul 2018 3 C

masonry buildings ― Guidelines

12 IS 13920:2016 Ductile design and detailing of reinforced concrete 2 C

structures subjected to seismic forces ― Code of
practice (first revision)

13 IS 13935:2009 Seismic evaluation, repair and strengthening of Aug 2019 C

masonry buildings ― Guidelines (first revision)

14 IS 15988:2013 Seismic evaluation and strengthening of existing Feb 2018 C

reinforced concrete buildings ― Guidelines

93
 FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 39 (15280) Draft Indian Standard Criteria for earthquake resistant design of structures:
Part 6 Base-isolated buildings [IS 1893 (Part 6)]

DRAFTS COMPLETED WIDE CIRCULATION

1 DOC:CED 39 (16890) Draft Indian Standard Confined Masonry for Earthquake Resistance ― Code of
Practice

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

94
CED 41 WATER-PROOFING AND DAMP-PROOFING
SCOPE STANDARDIZATION IN THE FIELD OF WATER-PROOFING AND DAMP-PROOFING MAINLY WITH
REFERENCE TO GENERAL BUILDING CONSTRUCTION INCLUDING SPECIFICATION FOR
MATERIALS, CODE OF PRACTICE AND METHODS OF TESTS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1322:1993 Bitumen felts for water-proofing and damp- Dec 2017 2 S

proofing ― Specification (fourth revision)

2 IS 1346:1991 Code of practice for waterproofing of roofs with Mar 2020 C

bitumen felts (third revision)

3 IS 1580:1991 Bituminous compounds for waterproofing and Mar 2020 S

caulking purposes ― Specification
(second revision)

4 IS 1609:1991 Damp-proofing treatment using bitumen felts ― Mar 2020 C

Code of practice (third revision)

5 *IS 3036:1992 Laying lime concrete for a waterproofed roof finish Dec 2017 C
― Code of practice (second revision)

6 IS 3037:1986 Specification for bitumen mastic for use in water Mar 2020 S
proofing of roofs (first revision)

7 IS 3067:1988 Code of practice for general design details and Apr 2020 C
preparatory work for damp-proofing and water
proofing of buildings (first revision)

8 IS 3384:1986 Specification for bitumen primer for use in Mar 2020 S

waterproofing and damp-proofing (first revision)

9 IS 4365:1967 Code of practice for application of bitumen mastic Mar 2020 C

for waterproofing of roofs

10 IS 4911:1986 Glossary of terms relating to bituminous Mar 2016 1 T

waterproofing and damp-proofing of buildings
(first revision)

11 IS 5871:1987 Specification for bitumen mastic for tanking and Mar 2020 S
damp- proofing (first revision)

12 IS 6494:1988 Code of practice for waterproofing of underground Mar 2020 C

water reservoirs and swimming pools
(first revision)

13 IS 7193:2013 Glass fibre base bitumen felts ― Specification May 2018 S

(second revision)

14 IS 7198:1974 Code of practice for damp-proofing using bitumen Mar 2020 C

mastic

15 IS 7290:1979 Recommendations for use of polyethylene film Mar 2020 1 C

for waterproofing of roofs (first revision)

95
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

16 IS 9918:1981 Code of practice for in-situ waterproofing and Mar 2020 C

damp-proofing treatment with glass fibre tissue
reinforced bitumen

17 IS 12027:1987 Specification for silicone-based water repellents Dec 2017 1 S

18 IS 12054:1987 Code of practice for application of silicone based Mar 2020 C

water repellents

19 IS 13182:2020 Waterproofing and damp-proofing of wet areas in C

building ― Recommendations (first revision)

20 *IS 13435 (Part 1):1992 Acrylic based polymer waterproofing materials ― Dec 2017 M
Methods of test: Part 1 Determination of solid
content

21 IS 13435 (Part 2):1992 Acrylic based polymer waterproofing materials ― Dec 2017 M
Methods of test: Part 2 Determination of coarse
particles

22 IS 13435 (Part 3):1992 Acrylic based polymer waterproofing material ― Dec 2017 1 M
Methods of test: Part 3 Determination of capillary
water take-up

23 IS 13435 (Part 4):1992 Acrylic based polymer waterproofing material ― Dec 2017 M
Methods of test: Part 4 Determination of pH value

24 IS 13826 (Part 1):1993 Bitumen based felt ― Methods of test: Dec 2017 1 M
Part 1 Breaking strength test

25 *IS 13826 (Part 2):1993 Bitumen based felt ― Methods of test: Dec 2017 1 M
Part 2 Pliability test

26 IS 13826 (Part 3):1993 Bitumen based felts ― Methods of test: Dec 2017 M
Part 3 Storage sticking test

27 IS 13826 (Part 4):1993 Bitumen based felts ― Methods of test: Dec 2017 1 M
Part 4 Pressure head test

28 IS 13826 (Part 5):1994 Bitumen based felt ― Methods of test: Dec 2017 M
Part 5 Heat resistance test

29 IS 13826 (Part 6):1993 Bitumen based felts ― Methods of test: Dec 2017 M
Part 6 Water absorption test

30 IS 13826 (Part 7):1993 Bitumen based felt ― Methods of test: Dec 2017 1 M
Part 7 Determination of binder content

31 IS 14695:1999 Glass fibre base coal tar pitch outerwrap ― Jan 2019 S
Specification

32 IS 16471:2017 Protection of below ground structures against C

water from the ground ― Guidelines

33 IS 16525:2017 Styrene butadiene styrene (SBS) modified S

bituminous waterproofing and damp-proofing
membrane with polyester reinforcement ―
Specification

96
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

34 IS 16526:2017 Atactic polypropylene (APP) modified bituminous S

waterproofing and damp-proofing membrane with
glass fibre reinforcement ― Specification

35 IS 16532:2017 APP modified bituminous water-proofing and S

damp-proofing membrane with polyester
reinforcement ― Specification

36 IS 16540:2017 Atactic polypropylene (APP) modified high S

molecular high density polyethylene (HMHDPE)
bituminous waterproofing and damp-proofing
membrane ― Specification

DRAFTS COMPLETED WIDE CIRCULATION

1 DOC:CED 41 (15498) Draft Indian Standard Acrylic based polymer waterproofing materials ― Methods of
test: Part 1 Determination of solid content [first revision of IS 13435 (Part 1)]

2 DOC:CED 41 (15555) Draft Indian Standard Bitumen based felts ― Methods of test: Part 2 Pliability test
[first revision of IS 13826 (Part 2)]

3 DOC:CED 41 (15606) Draft Indian Standard Code of practice for laying lime concrete for a waterproofed
roof finish (third revision of IS 3036)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

97
CED 43 SOIL AND FOUNDATION ENGINEERING
SCOPE FORMULATION OF INDIAN STANDARDS IN THE FIELD OF SOIL AND SOIL ENGINEERING
COVERING:
I) SUB-SURFACE EXPLORATION (OTHER THAN RIVER VALLEY PROJECTS);
II) SOIL SAMPLING AND TESTING INCLUDING STABILZED SOILS;
III) SOIL CLASSIFICATION FOR ENGINEERING PURPOSES;
IV) LOAD BEARING CAPACITIES OF SOILS; AND
V) GROUND IMPROVEMENT TECHNIQUES.

STANDARDIZATION IN THE FIELD OF FOUNDATION ENGINEERING IN PARTICULAR

DESIGN REQUIREMENTS AND CONSTRUCTION PRACTICES FOR VARIOUS TYPES OF
FOUNDATIONS AND SPECIAL LOAD TESTS ON FOUNDATIONS

LIAISON ISO/TC 182 (O) GEOTECHNICS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1080:1985 Code of practice for design and construction of Dec 2016 C

shallow foundations in soils (other than raft, ring
and shell) (second revision)

2 IS 1498:1970 Classification and identification of soils for general Dec 2016 2 M

engineering purposes (first revision)

3 IS 1888:1982 Method of load test on soils (second revision) Dec 2016 M

4 *IS 1892:1979 Code of practice for subsurface investigation for Dec 2016 C
foundations (first revision)

5 *IS 1904:1986 Code of practice for design and construction of May 2020 C
foundations in soils: General requirements
(third revision)

6 IS 2131:1981 Method for standard penetration test for soils Dec 2016 M
(first revision)

7 IS 2132:1986 Code of practice for thin walled tube sampling of Dec 2016 M
soils (second revision)

8 *IS 2720 (Part 1):1983 Methods of test for soils: Part 1 Preparation of dry May 2020 M
soil samples for various tests (second revision)

9 *IS 2720 (Part 2):1973 Methods of test for soils: Part 2 Determination of May 2020 1 M
water content (second revision)

10 IS 2720 (Part 3/Sec 1): Methods of test for soils: Part 3 Determination of Dec 2016 M
1980 specific gravity: Section 1 Fine grained soils
(first revision)

11 IS 2720 (Part 3/Sec 2): Methods of test for soils: Part 3 Determination of Dec 2016 M
1980 specific gravity: Section 2 Fine, medium and
coarse grained soils (first revision)

12 IS 2720 (Part 4):1985 Methods of test for soils: Part 4 Grain size analysis May 2020 M
(second revision)

98
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

13 IS 2720 (Part 5):1985 Methods of test for soils: Part 5 Determination of May 2020 M
liquid and plastic limit (second revision)

14 IS 2720 (Part 6):1972 Methods of test for soils: Part 6 Determination of Dec 2016 1 M
shrinkage factors (first revision)

15 IS 2720 (Part 7):1980 Methods of test for soils: Part 7 Determination of Dec 2016 2 M
water content-dry density relation using light
compaction (second revision)

16 IS 2720 (Part 8):1983 Methods of test for soils: Part 8 Determination of May 2020 M
water content-dry density relation using heavy
compaction (second revision)

17 IS 2720 (Part 9):1992 Methods of test for soils: Part 9 Determination of Dec 2016 M
dry density-moisture content relation by constant
mass of soil method (first revision)

18 IS 2720 (Part 10):1991 Methods of test for soils: Part 10 Determination of May 2020 M
unconfined compressive strength
(second revision)

19 IS 2720 (Part 11):1993 Methods of test for soils: Part 11 Determination of Dec 2016 M
the shear strength parameters of a specimen
tested in unconsolidated undrained triaxial
compression without the measurement of pore
water pressure (first revision)

20 IS 2720 (Part 12):1981 Methods of test for soils: Part 12 Determination of Dec 2016 M
shear strength parameters of soil from
consolidated undrained triaxial compression test
with measurement of pore water pressure
(first revision)

21 IS 2720 (Part 13):1986 Methods of test for soils: Part 13 Direct shear test Dec 2016 1 M
(second revision)

22 IS 2720 (Part 14):1983 Methods of test for soils: Part 14 Determination of May 2020 M
density index (relative density) of cohesionless
soils (first revision)

23 IS 2720 (Part 15):1986 Methods of test for soils: Part 15 Determination of Dec 2016 M
consolidation properties (first revision)

24 IS 2720 (Part 16):1987 Methods of test for soils: Part 16 Laboratory Dec 2016 M
determination of CBR (second revision)

25 IS 2720 (Part 17):1986 Methods of test for soils: Part 17 Laboratory Dec 2016 M
determination of permeability (first revision)

26 IS 2720 (Part 18):1992 Methods of test for soils: Part 18 Determination of Dec 2016 M
field moisture equivalent (first revision)

27 IS 2720 (Part 19):1992 Methods of test for soils: Part 19 Determination of Dec 2016 M
centrifuge moisture equivalent (first revision)

28 IS 2720 (Part 20):1992 Methods of test for soils: Part 20 Determination of Dec 2016 M
linear shrinkage (first revision)

99
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

29 IS 2720 (Part 21):1977 Methods of test for soils: Part 21 Determination of May 2020 1 M
total soluble solids (first revision)

30 IS 2720 (Part 22):1972 Methods of test for soils: Part 22 Determination of May 2020 1 M
organic matter (first revision)

31 IS 2720 (Part 23):1976 Methods of test for soils: Part 23 Determination of May 2020 M
calcium carbonate (first revision)

32 IS 2720 (Part 24):1976 Methods of test for soils: Part 24 Determination of May 2020 1 M
cation exchange capacity (first revision)

33 IS 2720 (Part 25):1982 Methods of test for soils: Part 25 Determination of May 2020 M
silica sesquioxide ratio (first revision)

34 IS 2720 (Part 26):1987 Methods of test for soils: Part 26 Determination of Dec 2016 M
pH value (second revision)

35 IS 2720 (Part 27):1977 Methods of test for soils: Part 27 Determination of May 2020 M
total soluble sulphates (first revision)

36 IS 2720 (Part 28):1974 Methods of test for soils: Part 28 Determination of May 2020 1 M
dry density of soils, in-place, by the sand
replacement method (first revision)

37 IS 2720 (Part 29):1975 Methods of test for soils: Part 29 Determination of May 2020 M
dry density of soils in-place, by the core-cutter
method (first revision)

38 IS 2720 (Part 30):1980 Methods of test for soils: Part 30 Laboratory vane Dec 2016 1 M
shear test (first revision)

39 IS 2720 (Part 31):1990 Methods of test for soils: Part 31 Field May 2020 M
determination of California bearing ratio
(first revision)

40 IS 2720 (Part 33):1971 Methods of test for soils: Part 33 Determination of May 2020 1 M
the density in place by the ring and water
replacement method

41 IS 2720 (Part 34):1972 Methods of test for soils: Part 34 Determination of May 2020 1 M
density of soil in place by rubber balloon method

42 IS 2720 (Part 35):1974 Methods of test for soils: Part 35 Measurement of May 2020 M
negative pore water pressure

43 IS 2720 (Part 36):1987 Methods of test for soils: Part 36 Laboratory Dec 2016 M
determination of permeability of granular soil
(constant head) (first revision)

44 IS 2720 (Part 37):1976 Methods of test for soils: Part 37 Determination of Dec 2016 M
sand equivalent value of soils and fine aggregates

45 IS 2720 (Part 38):1976 Methods of test for soils: Part 38 Compaction Dec 2016 M
control test (Hilf method)

46 IS 2720 (Part 39/Sec 1): Methods of test for soils: Part 39 Direct shear test Dec 2016 2 M
1977 for soils containing gravel: Section 1 Laboratory
test

100
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

47 IS 2720 (Part 39/Sec 2): Methods of test for soils: Part 39 Direct shear test Dec 2016 M
1979 for soils containing gravel: Section 2 In-situ shear
test

48 IS 2720 (Part 40):1977 Methods of test for soils: Part 40 Determination of Dec 2016 M
free swell index of soils

49 IS 2720 (Part 41):1977 Methods of test for soils: Part 41 Measurement of Dec 2016 M
swelling pressure of soils

50 IS 2809:1972 Glossary of terms and symbols relating to soil May 2020 T

engineering (first revision)

51 IS 2810:1979 Glossary of terms relating to soil dynamics Dec 2016 T

(first revision)

52 IS 2911 (Part 1/Sec 1): Design and construction of pile foundations ― May 2020 C
2010 Code of practice: Part 1 Concrete piles:
Section 1 Driven cast in-situ concrete piles
(second revision)

53 IS 2911 (Part 1/Sec 2): Design and construction of pile foundations ― May 2020 C
2010 Code of practice: Part 1 Concrete piles:
Section 2 Bored cast in-situ concrete piles
(second revision)

54 IS 2911 (Part 1/Sec 3): Design and construction of pile foundations ― May 2020 C
2010 Code of practice: Part 1 Concrete piles:
Section 3 Driven precast concrete piles
(second revision)

55 IS 2911 (Part 1/Sec 4): Design and construction of pile foundations ― May 2020 C
2010 Code of practice: Part 1 Concrete piles:
Section 4 Precast concrete piles in prebored holes
(first revision)

56 *IS 2911 (Part 2):1980 Code of practice for design and construction of pile May 2020 1 C
foundations: Part 2 Timber piles (first revision)

57 *IS 2911 (Part 3):1980 Code of practice for design and construction of pile May 2020 4 C
foundations: Part 3 Under-reamed piles
(first revision)

58 IS 2911 (Part 4):2013 Design and construction of pile foundations ― Nov 2018 M
Code of practice: Part 4 Load test on piles
(second revision)

59 IS 2950 (Part 1):1981 Code of practice for design and construction of raft Nov 2018 C
foundations: Part 1 Design (second revision)

60 *IS 2974 (Part 1):1982 Code of practice for design and construction of Nov 2018 1 C
machine foundations: Part 1 Foundations for
reciprocating type machines (second revision)

61 *IS 2974 (Part 2):1980 Code of practice for design and construction of Nov 2018 1 C
machine foundations: Part 2 Foundation for impact
type machines (hammer foundations)
(first revision)

101
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

62 *IS 2974 (Part 3):1992 Design and construction of machine foundations ― May 2020 C
Code of practice: Part 3 Foundations for rotary
type machines (medium and high frequency)
(second revision)

63 *IS 2974 (Part 4):1979 Code of practice for design and construction of May 2020 1 C
machine foundations: Part 4 Foundations for rotary
type machines of low frequency (first revision)

64 *IS 2974 (Part 5):1987 Code of practice for design and construction of Nov 2018 C
machine foundations: Part 5 Foundations for
impact machines other than hammer (forging and
stamping press, pig breaker, drop crusher and
jolter) (first revision)

65 *IS 4091:1979 Code of practice for design and construction of May 2020 C
foundations for transmission line towers and poles
(first revision)

66 IS 4332 (Part 1):1967 Methods of test for stabilized soils: Part 1 Method May 2020 1 M
of sampling and preparation of stabilized soils for
testing

67 IS 4332 (Part 2):1967 Methods of test for stabilized soils: May 2020 1 M
Part 2 Determination of moisture content of
stabilized soil mixtures

68 IS 4332 (Part 3):1967 Methods of test for stabilized soils: Part 3 Test for May 2020 1 M
determination of moisture content-dry density
relation for stabilized soil mixtures

69 IS 4332 (Part 4):1968 Methods of test for stabilized soils: Part 4 Wetting May 2020 1 M
and drying and freezing and thawing tests for
compacted soil-cement mixtures

70 IS 4332 (Part 5):1970 Methods of test for stabilized soils: May 2020 M
Part 5 Determination of unconfined compressive
strength of stabilized soils

71 IS 4332 (Part 6):1972 Methods of test for stabilized soils: Part 6 Flexural May 2020 1 M
strength of soil cement using simple beam with
third-point loading

72 IS 4332 (Part 7):1973 Methods of test for stabilized soils: May 2020 1 M
Part 7 Determination of cement content of cement
stabilized soils

73 IS 4332 (Part 8):1969 Methods of test for stabilized soils: May 2020 1 M
Part 8 Determination of lime content of lime
stabilized soils

74 IS 4332 (Part 9):1970 Methods of test for stabilized soils: May 2020 1 M
Part 9 Determination of bituminous stabilizer
content of bitumen and tar stabilized soils

75 IS 4332 (Part 10):1969 Methods of test for stabilized soils: Part 10 Test for May 2020 1 M
soil-bituminous mixtures

102
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

76 IS 4434:1978 Code of practice for in-situ vane shear test for soils Dec 2016 C
(first revision)

77 IS 4968 (Part 1):1976 Method for subsurface sounding for soils: Dec 2016 1 M
Part 1 Dynamic method using 50 mm cone without
bentonite slurry (first revision)

78 IS 4968 (Part 2):1976 Method for subsurface sounding for soils: Dec 2016 1 M
Part 2 Dynamic method using cone and bentonite
slurry (first revision)

79 IS 4968 (Part 3):1976 Method for subsurface sounding for soils: Dec 2016 M
Part 3 Static cone penetration test (first revision)

80 IS 5249:1992 Determination of dynamic properties of soil ― May 2020 1 M

Method of test (second revision)

81 IS 6403:1981 Code of practice for determination of breaking Dec 2016 2 C

capacity of shallow foundations (first revision)

82 IS 8009 (Part 1):1976 Code of practice for calculation of settlements of Nov 2018 3 C
foundations: Part 1 Shallow foundations subjected
to symmetrical static vertical loads

83 IS 8009 (Part 2):1980 Code of practice for calculation of settlement of May 2020 1 C
foundations: Part 2 Deep foundations subjected to
symmetrical static vertical loading

84 IS 8763:1978 Guide for undisturbed sampling of sands Dec 2016 M

85 IS 9198:1979 Specification for compaction rammer for soil testing Dec 2016 1 S

86 IS 9214:1979 Method for determination of modulus of subgrade Dec 2016 1 M

reaction (k-value) of soils in field

87 IS 9259:1979 Specification for liquid limit apparatus for soils Dec 2016 1 S

88 IS 9456:1980 Code of practice for design and construction of Nov 2018 1 C

conical and hyperbolic paraboloidal types of shell
foundations

89 IS 9556:1980 Code of practice for design and construction of Nov 2018 1 C

diaphragm walls

90 IS 9640:1980 Specification for split spoon sampler Dec 2016 2 S

91 IS 9669:1980 Specification for CBR moulds and its accessories Dec 2016 2 S

92 IS 9716:1981 Guide for lateral dynamic load test on piles Nov 2016 M

93 IS 9759:1981 Guidelines for dewatering during construction Nov 2016 1 C

94 IS 10042:1981 Code of practice for site investigations for Dec 2016 C

foundation in gravel-boulder deposit

95 IS 10074:1982 Specification for compaction mould assembly for May 2020 S

light and heavy compaction test for soils

103
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

96 IS 10077:1982 Specification for equipment for determination of May 2020 S

shrinkage factors

97 IS 10108:1982 Code of practice for sampling of soils by thin wall May 2020 C
sampler with stationary piston

98 IS 10270:1982 Guidelines for design and construction of Nov 2018 2 C

prestressed rock anchors

99 IS 10379:1982 Code of practice for field control of moisture and May 2020 C
compaction of soils of embankment and subgrade

100 IS 10442:1983 Specification for earth augers (spiral type) May 2020 S

101 IS 10589:1983 Specification for equipment for subsurface May 2020 S

sounding of soils

102 IS 10837:1984 Specification for moulds and accessories for May 2020 S
determination of density index (relative density) of
cohesionless soils

103 IS 11089:1984 Code of practice for design and construction of ring Dec 2016 1 C
foundation

104 IS 11196:1985 Specification for equipment for determination of May 2020 1 S

liquid limit of soils cone penetration method

105 IS 11209:1985 Specification for mould assembly for determination May 2020 S
of permeability of soils

106 IS 11229:1985 Specification for shear box for testing of soils May 2020 S

107 IS 11233:1985 Code of practice for design and construction of Dec 2016 C
radar antenna, microwave and TV tower
foundations

108 IS 11550:1985 Code of practice for field instrumentation of Dec 2016 C

swelling pressure in expansive soils

109 IS 11593:1986 Specification for shear box (large) for testing of May 2020 S
soils

110 IS 11594:1985 Specification for mild steel thin walled sampling May 2020 S
tubes and sampler heads

111 IS 11629:1986 Code of practice for installation and operation of Dec 2016 C
single point hydraulic over-flow setting gauge

112 IS 12023:1987 Code of practice for field monitoring of movement May 2020 C
of structures using tape extensometer

113 IS 12070:1987 Code of practice for design and construction of May 2020 1 C
shallow foundations on rocks

114 IS 12175:1987 Specification for rapid moisture meter for rapid Dec 2016 S
determination of water content for soil

104
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

115 IS 12208:1987 Method for measurement of earth pressure by May 2020 M

hydraulic pressure cell

116 IS 12287:1988 Specification for consolidometer for determination May 2020 S

of consolidation properties
117 IS 12979:1990 Mould for determination of linear shrinkage ― May 2020 S
Specification
118 *IS 13094:1992 Selection of ground improvement techniques for Dec 2016 C
foundation in weak soils ― Guidelines
119 IS 13301:1992 Vibration isolation for machine foundations ― Dec 2016 C
Guidelines
120 IS 13468:1992 Apparatus for determination of dry density of soil Dec 2016 S
by core cutter method ― Specification
121 IS 14593:1998 Design and construction of bored cast-in-situ piles Jun 2018 1 C
founded on rocks ― Guidelines
122 *IS 14893:2001 Non-destructive integrity testing of piles (NDT) ― May 2020 M
Guidelines
123 IS 15284 (Part 1):2003 Design and construction for ground improvement Jun 2018 C
― Guidelines: Part 1 Stone columns
124 IS 15284 (Part 2):2004 Design and construction for ground improvement May 2020 C
― Guidelines: Part 2 Pre consolidation using
vertical drains
125 SP 36 (Part 1):1987 Compendium of Indian standards on soil O
engineering: Part 1 Laboratory testing of soils for
civil engineering purposes
126 SP 36 (Part 2):1988 Compendium of Indian standards on soil O
engineering: Part 2 Field testing of soils for civil
engineering purposes

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 43 (13048) Draft Indian Standard Low strain non-destructive integrity testing of piles ―
Guidelines (first revision of IS 14893)

2 DCO:CED 43 (13916) Draft Indian Standard Design and construction of pile foundations ― Code of
practice: Part 2 Timber piles [second revision of IS 2911 (Part 2)]

3 DOC:CED 43 (14033) Draft Indian Standard Design and construction of pile foundations ― Code of
practice: Part 3 Under-reamed piles [second revision of IS 2911 (Part 3)]

4 DOC:CED 43 (14120) Draft Indian Standard Selection of ground improvement techniques for foundation
in weak soils ― Guidelines (first revision of IS 13094)

5 DOC:CED 43 (14122) Draft Indian Standard General requirements for design and construction of
foundations in soils ― Code of practice: General requirements (fourth revision of
IS 1904)

6 DOC:CED 43 (14250) Draft Indian Standard Subsurface Investigation for Foundation – Code of Practice
(second revision of IS 1892)

105
 DRAFTS COMPLETED WIDE CIRCULATION

1 DOC:CED 43 (12408) Draft Indian Standard Design and construction of machine foundations ― Code of
practice: Part 1 General provision (revision of IS 2974 Parts 1 to 5)

2 DOC:CED 43 (13116) Draft Indian Standard Design and construction of machine foundations ― Code of
practice: Part 2 Block foundation (revision of IS 2974 Parts 1 to 5)

3 DOC:CED 43 (13264) Draft Indian Standard Design and construction of machine foundations ― Code of
practice: Part 3 Frame foundation (revision of IS 2974 Parts 1 to 5)

4 DOC:CED 43 (14796) Methods of test for soils: Part 1 Preparation of dry soil samples for various tests
[third revision of IS 2720 (Part 1)]

5 DOC:CED 43 (14797) Methods of test for soils: Part 2 Determination of water content [third revision of
IS 2720 (Part 2)]

6 DOC:CED 43 (14121) Draft Indian Standard Design and construction of foundations for transmission line
towers and poles ― Code of practice (second revision of IS 4091)

DRAFT STANDARDS FORMULATED

1 Draft Indian Standard Design and construction of machine foundation ― Code of

DOC:CED 43 (14226) practice: Part 5 Foundation for machines (excluding hammers & presses)
supported on vibration isolation system [revision of IS 2974 (Part 1 to 5)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

106
CED 44 METHODS OF MEASUREMENT OF WORKS OF CIVIL ENGINEERING
(EXCLUDING WATER RESOURCES DEVELOPMENT DIVISION)
SCOPE STANDARDIZATION IN THE FIELD OF MEASUREMENT OF CIVIL ENGINEERING WORKS
(EXCLUDING THOSE RELATING TO WATER RESOURCES DEVELOPMENT)

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 1200 (Part 1):1992 Methods of measurement of building and civil Sep 2017 1 O
engineering works: Part 1 Earthwork
(fourth revision)

2 IS 1200 (Part 2):1974 Method of measurement of building and civil Sep 2017 2 O
engineering works: Part 2 Concrete works
(third revision)

3 IS 1200 (Part 3):1976 Method of measurement of building and civil Sep 2017 O
engineering works: Part 3 Brickwork
(third revision)

4 IS 1200 (Part 4):1976 Method of measurement of building and civil Sep 2017 1 O
engineering works: Part 4 Stone masonry
(third revision)

5 IS 1200 (Part 5):2013 Method of measurement of building and civil Jul 2018 O
engineering works: Part 5 Formwork
(fourth revision)

6 IS 1200 (Part 6):1974 Method of measurement of building and civil Sep 2017 2 O
engineering works: Part 6 Refractory work
(second revision)

7 IS 1200 (Part 7):2013 Method of measurement of building and civil Sep 2018 O
engineering works: Part 7 Hardware
(third revision)

8 IS 1200 (Part 8):1993 Methods of measurement of building and civil Sep 2017 1 O
engineering works: Part 8 Steelwork and ironwork
(fourth revision)

9 IS 1200 (Part 9):1973 Method of measurement of building and civil Sep 2017 1 O
engineering works: Part 9 Roof covering
(including cladding) (second revision)

10 IS 1200 (Part 10):2013 Method of measurement of building and civil Sep 2018 O
engineering works: Part 10 Ceiling and linings
(third revision)

11 IS 1200 (Part 11):2013 Method of measurement of building and civil Sep 2018 O
engineering works: Part 11 Paving, floor finishes,
dado and skirting (fourth revision)

12 IS 1200 (Part 12):1976 Method of measurement of building and civil Sep 2017 O
engineering works: Part 12 Plastering and
pointing (third revision)

107
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

13 IS 1200 (Part 13):1994 Method of measurement of building and civil Sep 2017 2 O
engineering works: Part 13 Whitewashing, colour
washing, distempering and painting of building
surfaces (fifth revision)

14 IS 1200 (Part 14):1984 Method of measurement of building and civil Sep 2017 1 O
engineering works: Part 14 Glazing
(third revision)

15 IS 1200 (Part 15):1987 Method of measurement of building and civil Sep 2017 1 O
engineering works: Part 15 Painting, polishing,
varnishing, etc (fourth revision)

16 IS 1200 (Part 16):1979 Method of measurement of building and civil Sep 2017 O
engineering works: Part 16 Laying of water and
sewer lines including appurtenant items
(third revision)

17 IS 1200 (Part 18):1974 Method of measurement of building and civil Sep 2017 O
engineering works: Part 18 Demolition and
dismantling (third revision)

18 IS 1200 (Part 19):1981 Method of measurement of building and civil Sep 2017 O
engineering works: Parts 19 Water supply,
plumbing and drains (third revision)

19 IS 1200 (Part 20):1981 Method of measurement of building and civil Sep 2017 O
engineering works: Part 20 Laying of gas and oil
pipelines (third revision)

20 IS 1200 (Part 21):1973 Method of measurement of building and civil Sep 2017 1 O
engineering works: Part 21 Woodwork and joinery
(second revision)

21 IS 1200 (Part 22):1982 Method of measurement of building and civil Sep 2017 O
engineering works: Part 22 Materials

22 IS 1200 (Part 23):1988 Method of measurement of building and civil Sep 2017 O
engineering works: Part 23 Piling (fourth revision)

23 IS 1200 (Part 24):1983 Method of measurement of building and civil Sep 2017 1 O
engineering works: Part 24 Well foundations
(third revision)

24 IS 1200 (Part 25):1971 Method of measurement of building and civil Sep 2017 4 O
engineering works: Part 25 Tunneling
(second revision)

25 IS 1200 (Part 26):1987 Method of measurement of building and civil Sep 2017 O
engineering work: Part 26 Acid resistant lining

26 IS 1200 (Part 27):2013 Method of measurement of building and civil Sep 2018 O
engineering works: Part 27 Earth work done by
mechanical appliances (first revision)

27 IS 1200 (Part 28):1992 Method of measurement of building and civil Sep 2017 O
engineering works: Part 28 Sound insulation work

108
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

28 IS 3861:2002 Method of measurement of plinth, carpet and Sep 2017 O

rentable areas of buildings (second revision)

29 SP 27:1987 Handbook of method of measurement of building O

works (first revision)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

109
CED 46 NATIONAL BUILDING CODE
SCOPE WORK RELATING TO NATIONAL BUILDING CODE OF INDIA

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED
1 SP 7: 2016 National Building Code of India 2016 (Vol 1 & 2) 1 O
Part 0 Integrated Approach - Prerequisite for
applying provisions of the Code
Part 1 Definitions
Part 2 Administration
Part 3 Development control rules and general
building requirements
Part 4 Fire and life safety
Part 5 Building materials
Part 6 Structural design
Section 1 Loads, forces and effects
Section 2 Soils and foundations
Volume 1 Section 3 Timber and bamboo
3A Timber
3B Bamboo
Section 4 Masonry
Section 5 Concrete
5A Plain and reinforced concrete
5B Prestressed concrete
Section 6 Steel
Section 7 Prefabrication, systems building and
mixed/composite construction
7A Prefabricated concrete
7B Systems building and mixed/
composite construction
Section 8 Glass and glazing

Part 7 Construction management, practices and

safety
Part 8 Building services
Section 1 Lighting and natural ventilation
Section 2 Electrical and allied installations
Section 3 Air conditioning, heating and
mechanical ventilation
Section 4 Acoustics, sound insulation and noise
control
Section 5 Installation of lifts, escalators and
moving walks
5A Lifts
Volume 2 5B Escalators and moving walks
Section 6 Information and communication
enabled installations
Part 9 Plumbing services (including solid waste
management)
Section 1 Water supply
Section 2 Drainage and sanitation
Section 3 Solid waste management
Section 4 Gas supply
Part 10 Landscape development, signs and
outdoor display structures
Section 1 Landscape planning, design and
development
Section 2 Signs and outdoor display structures

110
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.
Part 11 Approach to sustainability
Part 12 Asset and facility management

Group 1 Part 0 Integrated Approach - Prerequisite for 1

For Planning Building/ applying provisions of the Code
Development Work Part 1 Definitions
Part 2 Administration
Part 3 Development control rules and general
building requirements
Part 4 Fire and life safety
Part 5 Building materials
Part 10 Landscape development, signs and
outdoor display structures
Section 1 Landscape planning, design and
development
Section 2 Signs and outdoor display structures
Part 11 Approach to sustainability

Group 2 Part 0 Integrated Approach - Prerequisite for

For Structural Design applying provisions of the Code
Part 6 Structural design
Section 1 Loads, forces and effects
Section 2 Soils and foundations
Section 3 Timber and bamboo
3A Timber
3B Bamboo
Section 4 Masonry
Section 5 Concrete
5A Plain and reinforced concrete
5B Prestressed concrete
Section 6 Steel
Section 7 Prefabrication, systems building and
mixed/composite construction
7A Prefabricated concrete
7B Systems building and mixed/
composite construction
Section 8 Glass and glazing
Part 11 Approach to sustainability

Group 3 Part 0 Integrated Approach - Prerequisite for

For Aspects relating to applying provisions of the Code
Construction and Asset Part 7 Construction management, practices and
& Facility Management Safety
Part 11 Approach to sustainability
Part 12 Asset and facility management

Group 4 Part 0 Integrated Approach - Prerequisite for

For Building Services applying provisions of the Code
Part 8 Building services
Section 1 Lighting and natural ventilation
Section 2 Electrical and allied installations
Section 3 Air conditioning, heating and
mechanical ventilation
Section 4 Acoustics, sound insulation and noise
control
Section 5 Installation of lifts, escalators and
moving walks
5A Lifts
5B Escalators and moving walks

111
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.
Section 6 Information and communication
enabled installations
Part 11 Approach to sustainability

Group 5 Part 0 Integrated Approach - Prerequisite for

For Plumbing Services applying provisions of the Code
Part 9 Plumbing services (including solid waste
management)
Section 1 Water supply
Section 2 Drainage and sanitation
Section 3 Solid waste management
Section 4 Gas supply
Part 11 Approach to sustainability

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

112
CED 47 PORTS, HARBOURS AND OFFSHORE INSTALLATIONS
SCOPE FORMULATION OF STANDARDS, CODES AND RECOMMENDATIONS RELATING
SPECIFICALLY TO,
I) PORTS AND HARBOURS AND OTHER ANCILLARY STRUCTURES
II) OFFSHORE STRUCTURES

LIAISON ISO/TC 67/SC 7 (O) OFFSHORE STRUCTURES

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 4651 (Part 1):2020 Planning and design of ports and harbours ― Code C
of practice: Part 1 Site investigation
(second revision)

2 IS 4651 (Part 2):2020 Planning and design of ports and harbours ― Code C
of practice: Part 2 Geotechnical engineering
(second revision)

3 IS 4651 (Part 3):2020 Planning and design of ports and harbours ― Code C
of practice: Part 3 Loading (second revision)

4 IS 4651 (Part 4):2014 Planning and design of ports and harbours ― Code Aug 2019 C
of practice: Part 4 General design considerations
(third revision)

5 IS 4651 (Part 5):1980 Code of practice for planning and design of ports Jul 2017 C
and harbours: Part 5 Layout and functional
requirements

6 IS 7314:1974 Glossary of terms relating to port and harbour Jul 2017 T

engineering

7 IS 9527 (Part 1):1981 Code of practice for design and construction of port Jul 2017 C
and harbour structures: Part 1 Concrete monoliths

8 IS 9527 (Part 3):1983 Code of practice for design and construction of port Jul 2017 C
and harbour structures: Part 3 Sheet pile walls

9 IS 9527 (Part 4):1980 Code of practice for design and construction of port Jul 2017 C
and harbour structures: Part 4 Cellular sheet pile
structures
10 IS 9527 (Part 6):1989 Design and construction port and harbour Aug 2020 C
Structures ― Code of practice: Part 6 Block work
11 IS 10020 (Part 4):1981 Recommendations for design and construction of Jul 2017 O
port and harbour components: Part 4 Slipways

* INDICATES STANDARDS UNDER REVISION ** INDICATES STANDARDS TO BE REVISED

113
CED 48 ROCK MECHANICS
SCOPE FORMULATION OF INDIAN STANDARDS IN THE FIELD OF ROCK MECHANICS COVERING
FIELD AND LABORATORY TESTS, ROCK SAMPLING, CLASSIFICATION OF ROCK AND ROCK
MASSES FOR ENGINEERING PURPOSES, LOAD BEARING CAPACITIES OF ROCK MASSES,
IMPROVEMENT OF ROCK MASS AND ROCK SLOPES

LIAISON ISO/TC 182 (O) GEOTECHNICS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 7317:2020 Uniaxial jacking test for deformation modulus of C

rock mass  Code of practice (second revision)

2 *IS 7746:1991 In-situ shear test on rock  Code of practice Apr 2020 C
(first revision)

3 IS 8764:1998 Method of determination of point load strength Mar 2019 2 M

index of rocks (first revision)

4 IS 9143:1979 Method for the determination of unconfined Apr 2016 M

compressive strength of rock materials

5 IS 9179:1979 Method for the preparation of rock specimen for Apr 2016 M
laboratory testing

6 IS 9221:1979 Method for the determination of modulus of Apr 2016 M

elasticity and Poisson's ratio of rock materials in
uniaxial compression

7 IS 10050:1981 Method for determination of slake durability index of Apr 2016 M

rocks

8 IS 10082:1981 Method of test for determination of tensile strength Apr 2016 M

by indirect tests on rock specimens

9 IS 10782:1983 Method for the laboratory determination of dynamic Apr 2016 M

modulus of rock core specimens

10 IS 11309:1985 Method of conducting pull-out test on anchor bars Apr 2016 M

and rock bolts

11 IS 11315 (Part 1):1987 Methods for quantitative description of Apr 2016 M

discontinuities in rock mass: Part 1 Orientation

12 IS 11315 (Part 2):1987 Methods for quantitative description of Apr 2016 M

discontinuities in rock mass: Part 2 Spacing

13 IS 11315 (Part 3):1987 Methods for quantitative description of Apr 2020 M

discontinuities in rock mass: Part 3 Persistence

14 IS 11315 (Part 4):1987 Methods for quantitative descriptions of Apr 2020 M

discontinuities in rock mass: Part 4 Roughness

15 IS 11315 (Part 5):1987 Method for the quantitative descriptions of Apr 2016 M
discontinuities in rock mass: Part 5 Wall strength

114
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

16 IS 11315 (Part 6):1987 Method for the quantitative descriptions of Apr 2016 M
discontinuities in rock mass: Part 6 Aperture

17 IS 11315 (Part 7):1987 Methods for quantitative description of Apr 2020 M

discontinuities in rock mass: Part 7 Filling

18 IS 11315 (Part 8):1987 Methods for quantitative description of Apr 2020 M

discontinuities in rock mass: Part 8 Seepage

19 IS 11315 (Part 9):1987 Method for the quantitative descriptions of Apr 2016 M
discontinuities in rock masses: Part 9 Number of
sets

20 IS 11315 (Part 10):1987 Method for the quantitative descriptions of Apr 2016 M
discontinuities in rock masses: Part 10 Block size

21 IS 11315 (Part 11):1985 Method for the quantitative descriptions of Apr 2016 M
discontinuities in rock masses: Part 11 Core
recovery and rock quality designation

22 IS 11315 (Part 12):1992 Quantitative description of discontinuities in rock Apr 2016 M

mass ─ Methods: Part 12 Drill core study

23 IS 11358:1987 Glossary of terms and symbols relating to rock Apr 2020 T

mechanics

24 IS 12608:1989 Method for determination of hardness of rock Apr 2020 M

25 IS 12634:1989 Rock joints ― Direct shear strength ― Laboratory Apr 2020 1 M

method of determination

26 IS 12955 (Part 1):1990 Code of practice for in-situ determination of rock Apr 2016 C
mass deformability using a flexible dilatometer:
Part 1 With volume change

27 IS 12955 (Part 2):1990 In-situ determination of rock mass deformability Apr 2016 C
using a flexible dilatometer ― Code of practice:
Part 2 With radial displacement

28 IS 13030:1991 Method of test for laboratory determination of water Apr 2016 M

content, porosity, density and related properties of
rock material

29 IS 13047:1991 Method for determination of strength of rock Apr 2016 1 M

materials in triaxial compression

30 IS 13063:1991 Structural safety of buildings on shallow Apr 2016 C

foundations on rocks ― Code of practice

31 IS 13365 (Part 1):1998 Quantitative classification systems of rock mass ― Apr 2016 1 O
Guidelines: Part 1 Rock mass rating (RMR) for
predicting of engineering properties

32 IS 13365 (Part 2):2019 Quantitative classification systems of rock mass ― O

Guidelines: Part 2 Rock mass quality for prediction
of support pressure and engineering properties in
underground openings (first revision)

33 IS 13365 (Part 3):1997 Quantitative classification system of rock mass ― Apr 2017 O
Guidelines: Part 3 Determination of slope mass
rating (SMR)

115
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

34 IS 13365 (Part 4):2014 Quantitative Classification System of Rock Mass Jul 2019 O
― Guidelines: Part 4 Geological Strength Index
(GSI)

35 IS 13372 (Part 1):1992 Seismic testing of rock mass ― Code of practice: Apr 2016 C
Part 1 Within a borehole

36 IS 13372 (Part 2):1992 Seismic testing of rock mass ― Code of practice: Apr 2016 C
Part 2 Between the boreholes

37 IS 13414:1992 Monitoring of rock movements using multi-point Apr 2016 O

borehole extensometers ― Guidelines

38 *IS 13946 (Part 1):1994 Determination of rock stress ― Code of practice: Apr 2020 C
Part 1 Using the hydraulic fracturing technique

39 IS 13946 (Part 2):1994 Determination of rock stress ― Code of practice: Apr 2020 C
Part 2 Using a USBM-type drillhole deformation
gauge

40 IS 13946 (Part 3):1994 Determination of rock stress ― Code of practice: Apr 2020 C
Part 3 Using a CSIR or CSIRO type cell with 9 or
12 strain gauges

41 IS 13946 (Part 4):1994 Determination of rock stress ― Code of practice: Apr 2020 C
Part 4 Using flat jack technique

42 IS 14243 (Part 1):1995 Selection and development of site for building in hill Apr 2020 C
areas ― Guidelines: Part 1 Microzonation of urban
centres

43 IS 14243 (Part 2):1995 Selection and development of site for building in hill Apr 2020 C
areas ― Guidelines: Part 2 Selection and
development

44 IS 14395:1996 Monitoring of rock movements using probe Apr 2017 1 C

inclinometer ― Guidelines

45 IS 14396 (Parts 1 to 4): Argillaceous swelling rocks ― Methods for Apr 2016 M
1996 laboratory testing:
Part 1 Method for sampling storage and
preparation of test specimens
Part 2 Method for determining maximum axial
swelling stress
Part 3 Method for determining axial and radial free
swelling strain
Part 4 Method for determining axial swelling stress
as a function of axial swelling strain

46 IS 14436:1997 Guidelines on determination of resistivity of rock Apr 2017 1 M

specimen

47 IS 14448:1997 Code of practice for reinforcement of rock slopes Apr 2017 1 C

with plane wedge failure

48 IS 14881:2001 Method for blast vibration monitoring ― Guidelines Apr 2016 M

116
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

49 IS 15026:2002 Guidelines for tunneling methods in rock masses Apr 2017 C

50 IS 15180:2002 Guidelines for use in the prediction of subsidence Apr 2017 C

and associated parameters in coal mines having
nearly horizontal single seam workings

51 IS 17446:2020 Observational method for tunnelling in rock masses C

— Guidelines

52 IS 17511:2020 Borehole jack test for determination of modulus of C

deformation of rock mass — Code of Practice

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 48 (16116) Draft Indian Standard In-situ shear test on rock — Code of practice (first revision of
IS 7746)

DRAFT STANDARDS FORMULATED

2 DCO:CED 48 (16126) Draft Indian Standard Determination of rock stress — Code of practice:
Part 1 Using the hydraulic fracturing technique [first revision of IS 13946 (Part 1)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

117
CED 50 PLASTIC PIPING SYSTEM
SCOPE STANDARDIZATION OF PIPES, FITTINGS AND AUXILIARIES INTENDED FOR THE TRANSPORT
OF FLUIDS AND FOR CABLE DUCTING MADE FROM ALL TYPES OF PLASTIC MATERIALS
INCLUDING REINFORCED PLASTICS METAL FITTINGS AND RUBBER GASKETS USED WITH
PLASTIC PIPES.THE SCOPE FURTHER COVERS STANDARDIZATION FOR DIMENSIONS AND
THEIR TOLERANCES, REQUIREMENTS AND TEST METHODS FOR CHEMICAL, MECHANICAL
AND PHYSICAL PROPERTIES AS RELEVANT TO PARTICULAR APPLICATION AND CODES OF
PRACTICES FOR LAYING AND INSTALLATION

LIAISON ISO/TC 138 (O) PLASTIC PIPES, FITTINGS AND VALVES FOR THE TRANSPORT OF FLUIDS
ISO/TC 138 SC 1 (O) PLASTIC PIPES AND FITTINGS FOR SOIL, WASTEAND DRAINAGE
(INCLUDING LAND DRAINAGE)
ISO/TC 138 SC 2 (O) PLASTIC PIPES AND FITTINGS FOR WATER SUPPLIES
ISO/TC 138 SC 3 (O) PLASTIC PIPES AND FITTINGS FOR INDUSTRIAL APPLICATION
ISO/TC 138 SC 4 (O) PLASTIC PIPES AND FITTINGS FOR SUPPLY OF GASEOUS FUELS
ISO/TC 138 SC 5 (O) GENERAL PROPERTIES OF PIPES, FITTINGS AND VALVES OF PLASTIC
MATERIALS AND THEIR ACCESSORIES, TEST METHODS AND BASIC SPECIFICATION
ISO/TC 138 SC 6 (O) REINFORCED PLASTIC PIPES AND FITTINGS FOR ALL APPLICATIONS
ISO/TC 138 SC 7 (O) VALVES AND AUXILIARY EQUIPMENT OF PLASTIC MATERIALS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 4984:2016 Polyethylene pipes for water supply 1 S

(fifth revision) ― Specification

2 *IS 4985:2000 Unplasticized PVC pipes for potable water Mar 2020 5 S
supplies ― Specification (third revision)

3 IS 7634 (Part 1):1975 Code of practice for plastics pipes work for Sep 2017 2 C
potable water supplies: Part 1 Choice of
materials and general recommendations

4 IS 7634 (Part 2):2012 Plastics pipes selection, handling, storage and Jun 2017 C
installation for potable water supplies ― Code of
practice: Part 2 Laying and jointing of
polyethylene (PE) pipes (first revision)

5 IS 7634 (Part 3):2003 Plastic pipes selection, handling, storage and May 2018 C
installation for potable water supplies ― Code of
practice: Part 3 Laying and jointing of UPVC
pipes (first revision)

6 IS 7834 (Part 1):1987 Specification for injection moulded PVC socket May 2018 S
fittings with solvent cement joints for water
supplies: Part 1 General requirements
(first revision)

7 IS 7834 (Part 2):1987 Specification for injection moulded PVC socket May 2018 S
fittings with solvent cement joints for water
supplies: Part 2 Specific requirements for 45°
elbows (first revision)

8 IS 7834 (Part 3):1987 Specification for injection moulded PVC socket May 2018 S
fittings with solvent cement joints for water
supplies: Part 3 Specific requirements for 90°
elbows (first revision)

118
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

9 IS 7834 (Part 4):1987 Specification for injection moulded PVC socket May 2018 S
fittings with solvent cement joints for water
supplies: Part 4 Specific requirements for 90°
tees (first revision)

10 IS 7834 (Part 5):1987 Specification for injection moulded PVC socket May 2018 S
fittings for solvent cement joints for water
supplies: Part 5 Specific requirements for 45°
tees (first revision)

11 IS 7834 (Part 6):1987 Specification for injection moulded PVC socket May 2018 S
fittings with solvent cement joints for water
supplies: Part 6 Specific requirements for sockets
(first revision)

12 IS 7834 (Part 7):1987 Specification for injection moulded PVC socket May 2018 S
fittings with solvent cement joints for water
supplies: Part 7 Specific requirements for unions
(first revision)

13 IS 7834 (Part 8):1987 Specification for injection moulded PVC socket May 2018 S
fittings with solvent cement joints for water
supplies: Part 8 Specific requirements for caps
(first revision)

14 *IS 8008 (Part 1):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 1 General
requirements for fittings (first revision)

15 *IS 8008 (Part 2):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 2 Specific
requirements for 90° bend (first revision)

16 *IS 8008 (Part 3):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 3 Specific
requirements for 90° tees(first revision)

17 *IS 8008 (Part 4):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 4 Specific
requirements for reducers (first revision)

18 *IS 8008 (Part 5):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 5 Specific
requirements for ferrule reducers (first revision)

19 *IS 8008 (Part 6):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 6 Specific
requirements for pipe ends (first revision)

20 *IS 8008 (Part 7):2003 Injection moulded/machined high density May 2018 1 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 7 Specific
requirements for sandwich flanges (first revision)

119
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

21 *IS 8008 (Part 8):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 8 Specific
requirements for reducing tees (first revision)

22 *IS 8008 (Part 9):2003 Injection moulded/machined high density May 2018 S
polyethylene (HDPE) fittings for potable water
supplies ― Specification: Part 9 Specific
requirements for ends caps (first revision)

23 *IS 8360 (Part 1):1977 Specification for fabricated high density Sep 2017 S
polyethylene (HDPE) fittings for potable water
supplies: Part 1 General requirements

24 *IS 8360 (Part 2):1977 Specification for fabricated high density Sep 2017 S
polyethylene (HDPE) fittings for potable water
supplies: Part 2 Specific requirements for 90°
tees

25 *IS 8360 (Part 3):1977 Specification for fabricated high density Sep 2017 S
polyethylene (HDPE) fittings for potable water
supplies: Part 3 Specific requirements for 90°
bends

26 IS 9271:2004 Unplasticized polyvinyl chloride (UPVC) single Apr 2019 2 S

wall corrugated pipes for drainage ―
Specification (first revision)

27 IS 10124 (Part 1):2009 Fabricated PVC-U fittings for potable water Apr 2019 1 S
supplies ― Specification: Part 1 General
requirements (second revision)

28 IS 10124 (Part 2):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 2 Specific
requirements for sockets (second revision)

29 IS 10124 (Part 3):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 3 Specific
requirements for straight reducers
(second revision)

30 IS 10124 (Part 4):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 4 Specific
requirements for caps (second revision)

31 IS 10124 (Part 5):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 5 Specific
requirements for equal tees (second revision)

32 IS 10124 (Part 6):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 6 Specific
requirements for flanged tail pieces with metallic
flanges (second revision)

33 IS 10124 (Part 7):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 7 Specific
requirements for threaded adaptors
(second revision)

120
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

34 IS 10124 (Part 8):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 8 Specific
requirements for 90° bends
(second revision)

35 IS 10124 (Part 9):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 9 Specific
requirements for 60° degree bends
(second revision)

36 IS 10124 (Part 10):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 10 Specific
requirements for 45° bends
(second revision)

37 IS 10124 (Part 11):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 11 Specific
requirements for 30° bends
(second revision)

38 IS 10124 (Part 12):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 12 Specific
requirements for 22 1/2° bends
(second revision)

39 IS 10124 (Part 13):2009 Fabricated PVC-U fittings for potable water Apr 2019 S
supplies ― Specification: Part 13 Specific
requirements for 11 1/4° bends
(second revision)

40 IS 12231:1987 Specification for unplasticized PVC pipes for use May 2018 S
in suction and delivery lines of agricultural pump
sets

41 IS 12235 (Parts1 to19): Thermoplastics pipes and fittings ― Methods of Apr 2019 M
2004 test (first revision)

IS 12235 (Part 1):2004 Part 1 Measurement of dimensions

IS 12235 (Part 2):2004 Part 2 Determination of vicat softening

temperature

IS 12235 (Part 3):2004 Part 3 Test for opacity 1

IS 12235 (Part 4):2004 Part 4 Determining the detrimental effect on the 1

composition of water

IS 12235 (Part5/Sec1): Part 5 Longitudinal reversion

2004 Section 1 Determination methods

IS 12235 (Part 5/Sec2): Part 5 Longitudinal reversion

2004 Section 2 Determination parameters

IS 12235 (Part 6):2004 Part 6 Stress relief test

IS 12235 (Part 7):2004 Part 7 Resistance of sulphuric acid

121
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

IS 12235 (Part 8/Sec 1): Part 8 Resistance to internal hydrostatic

2004 pressure
Section 1 Resistance to internal hydrostatic
pressure at constant internal water pressure

IS 12235 (Part 8/Sec 2): Part 8 Resistance to internal hydrostatic

2004 pressure
Section 2 Leak-tightness of elastomeric sealing
ring type socket joints under positive internal
pressure and with angular deflection

IS 12235 (Part 8/Sec 3): Part 8 Resistance to internal hydrostatic

2004 pressure
Section 3 Leak-tightness of elastomeric sealing
ring type socket joints under negative internal
pressure and with angular deflection

IS 12235 (Part 8/Sec 4): Part 8 Resistance to internal hydrostatic

2004 pressure
Section 4 Leak-tightness of elastomeric sealing
ring type socket joints under positive internal
pressure without angular deflection

IS 12235 (Part 9):2004 Part 9 Resistance to external blows (Impact

resistance) at 0° C (Round-the-clock method)

IS 12235 (Part 10):2004 Part 10 Determination of organotin as tin

aqueous solution

IS 12235 (Part 11):2004 Part 11 Resistance to dichloromethane at

specified temperature

IS 12235 (Part 12):2004 Part 12 Determination of titanium dioxide content

IS 12235 (Part 13):2004 Part 13 Determination of tensile strength and

elongation

IS 12235 (Part 14):2004 Part 14 Determination of density/relative density

(specific gravity)

IS 12235 (Part 15):2004 Part 15 Determination of vinyl chloride monomer

content

IS 12235 (Part 16):2004 Part 16 High temperature test

IS 12235 (Part 17):2004 Part 17 Determination of ash content and

sulphated ash content

IS 12235 (Part 18):2004 Part 18 Determination of ring stiffness

IS 12235 (Part 19):2004 Part 19 Flattering test

42 IS 12709:1994 Glass-fibre reinforced plastics (GRP) pipes, joints Apr 2019 5 S

and fittings for use for potable water supply ―
Specification (first revision)

122
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

43 IS 12818:2010 Unplasticized polyvinyl chloride (PVC-U) screen Mar 2021 2 S

and casing pipes for bore/tubewells ―
Specification (second revision)

44 IS 13592:2013 Unplasticized polyvinyl chloride (PVC-U) pipes May 2018 1 S

for soil and waste discharge system for inside
and outside buildings including ventilation and
rain water system ― Specification (first revision)

45 IS 13593:1992 UPVC pipe fittings for use with UPVC pipes in Sep 2017 S
the suction and delivery lines of agricultural
pumps ― Specification

46 IS 13916:1994 Installation of glassfibre reinforced plastic (GRP) Apr 2019 C

piping system ― Code of practice

47 *IS 14333:1996 High density polyethylene pipes for sewerage ― Jan 2017 4 S
Specification

48 IS 14402:1996 Glass Fibre Reinforced Plastics (GRP) pipes, Jan 2017 2 S

joints and fittings for use for sewerage, industrial
waste and water (other than potable) ―
Specification

49 IS 14735:1999 Unplasticized polyvinyl chloride (UPVC) injection Apr 2019 3 S

moulded fittings for soil and waste discharge
system for inside and outside buildings including
ventilation and rain water system ― Specification

50 IS 14787:2000 Unplasticized PVC pipes (ducts) and fittings for Mar 2020 1 S
underground telecommunications cable
installation ― Specification

51 *IS 14885:2001 Polyethylene pipes for supply of gaseous fuels ― Jan 2017 3 S
Specification

52 IS 15265:2003 Flexible PVC pipes or polymer reinforced May 2018 1 S

thermoplastic hoses for suction and delivery lines
of agricultural pumps ― Specification
53 IS 15328:2003 Unplasticized non-pressure polyvinyl chloride May 2018 6 S
(PVC-U) pipes for use in underground drainage
and sewerage systems ― Specification

54 IS 15450:2004 Polyethylene/aluminium/polyethylene composite Apr 2019 2 S

pressure pipes for hot and cold water supplies ―
Specification

55 IS 15778:2007 Chlorinated polyvinyl chloride (CPVC) pipes for Sep 2017 3 S

potable hot and cold water distribution supplies
― Specification

56 IS 15801:2008 Polypropylene-random copolymer pipes for hot Sep 2017 1 S

and cold water supplies ― Specification

57 IS 15927 (Part 1):2012 Polyethylene fittings for use with polyethylene May 2017 S
pipes for the supply of gaseous fuels ―
Specification: Part 1 Fittings for socket fusion
using heated tools

123
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

58 IS 15927 (Part 2):2012 Polyethylene fittings for use with polyethylene Jan 2017 S
pipes for the supply of gaseous fuels ―
Specification: Part 2 Spigot fittings for butt fusion
for socket fusion using heated tools, and for use
with electro fusion fittings

59 IS 15927 (Part 3):2011 Polyethylene fittings for use with polyethylene Mar 2021 S
pipes for the supply of gaseous fuels ―
Specification: Part 3 Electro fusion fittings

60 IS 16098 (Part 1):2013 Structured - wall plastics piping systems for non- Mar 2018 1 S
pressure drainage and sewerage ―
Specification: Part 1 Pipes and fittings with
smooth external surface, Type A

61 IS 16098 (Part 2):2013 Structured - Wall plastics piping systems for non- Mar 2018 2 S
pressure drainage and sewerage ―
Specification: Part 2 Pipes and fittings with non-
smooth external surface, Type B

62 IS 16130:2014 Thermoplastics materials for pipes and fittings for Jan 2019 O
/ISO 12162:2009 pressure applications ― Classification,
designation and design coefficient

63 IS 16462:2016 Plastic piping and ducting systems ― Mar 2021 M

/ISO 9080:2012 Determination of the long-term hydrostatic
strength of thermoplastics materials in pipe form
by extrapolation

64 IS 16268:2017 Plastics pipes and fittings ‒ Combined chemical- O

/ISO/TR 10358:1993 resistance classification table

65 IS 16647:2017 Oriented unplasticized polyvinyl chloride S

(PVC-O) pipes for water supply ― Specification

66 SP 57: 1993 Handbook for pipes and fittings for drinking water O
supply

FINLIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 50 (12111) Draft for Multilayer (PE-AL-PE) plastics piping systems for indoor gas installations
with maximum operating pressure up to and including 500 kA (5 Bar) ―
Specification

2 DOC:CED 50 (13621) Draft Indian Standard for Fabricated polyethylene fittings for water supplies —
Specification [first revision of IS 8360 (Parts 1 to 3)]

3 DOC:CED 50 (13622) Draft Indian Standard for Injection moulded/machined polyethylene fittings for
water supply — Specification [second revision of IS 8008 (Parts 1 to 9)]

4 DOC:CED 50 (13623) Draft Amendment No. 2 to IS 4984:2016 Polyethylene pipes for water supply —
Specification (fifth revision)

5 DOC:CED 50 (13636) Draft Indian Standard Polyethylene pipes for sewerage and industrial chemicals
and effluents — Specification [first revision of IS 14333]

124
6 DOC:CED 50 (13670) Draft Indian Standard Polyethylene pipes for the supply of gaseous fuels —
Specification (first revision of IS 14885)

7 DOC:CED 50 (13682) Draft Indian Standard Chlorinated polyvinyl chloride (CPVC) fittings for potable hot
and cold water distribution supplies ― Specification

8 DOC:CED 50 (13686) Draft Indian Standard Polyethylene-aluminium-polyethylene composite pressure

pipes for hot and cold water supplies — Specification (first revision of IS 15450)

9 DOC:CED 50 (14798) Draft Indian Standard Unplasticized PVC pipes for water supplies ― Specification
(fourth revision of IS 4985)

DRAFT STANDARDS FORMULATED

1 DOC:CED 50 (15536) Draft Indian Standard Flexible polyvinyl chloride lay flat hose for agriculture use —
Specification

2 DOC:CED 50 (15770) Draft Indian Standard Unplasticized polyvinyl chloride (PVC-U) threaded pipes and
couples for borewell — Specification

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

125
CED 51 PLANNING, HOUSING AND PREFABRICATED CONSTRUCTION
SCOPE FORMULATION OF STANDARDS:
a) TO COVER VARIOUS ASPECTS OF PLANNING IN RURAL AND URBAN AREAS, BUILDING
BYELAWSINCLUDING ZONING REGULATIONS, PRIMARY ELEMENTS IN THE DESIGN OF
BUILDINGSFOR VARIOUS USES, BUILDINGS MODULES AND MODULAR CO-ORDINATION,
ARCHITECTURAL AND BUILDING DRAWING PRACTICES AND PLANNING OF DRAWING
OFFICES
b) TO ASSIST IN THE HOUSING PROGRAMME FOR ALL GROUPS, RURAL HOUSING, ETC NOT
COVERED BY OTHER COMMITTEES; CO-ORDINATION OF WORK IN THIS AREA BY OTHER
COMMITTEES,STANDARD REQUIRED FOR IMPLEMENTING HOUSING PROGRAMME WITHIN
THE PROVISIONS OF NATIONAL HOUSING AND HABITAT POLICY OF THE GOVERNMENT, AND
c) ON DESIGN AND CONSTRUCTION PRACTICES IN THE FIELD OF PREFABRICATED
CONSTRUCTION

LIAISON ISO/TC 59 (O) BUILDINGS AND CIVIL ENGINEERING WORKS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 962:1989 Code of practice for architectural and building Jan 2017 C

drawings (second revision)

2 IS 1553:1989 Design of library buildings ― Recommendations Mar 2021 C

relating to its primary elements (second revision)

3 IS 2661:1978 Specification for mobile library van (first revision) Oct 2018 S

4 IS 2662:1978 Specification for packages for use of libraries Oct 2018 S

(first revision)

5 IS 2663:1989 Design of buildings for archives ― Mar 2021 C

Recommendations relating to its primary elements
(second revision)

6 IS 3201:1988 Criteria for design and construction of precast Apr 2019 C

concrete trusses and purlins (first revision)

7 IS 4878:1986 Byelaws for construction of cinema buildings Mar 2021 C

(first revision)

8 IS 4919:1981 Glossary of terms applicable to landscape and Oct 2018 T

horticulture work (first revision)

9 IS 4993:1983 Glossary of terms relating to modular co-ordination Mar 2021 T

(second revision)

10 IS 5197:1987 Recommendations for layout and planning of Oct 2018 C

drawings offices (first revision)

11 IS 6072:1971 Specification for autoclaved reinforced cellular Jan 2017 3 S

concrete wall slabs

12 IS 6073:2006 Autoclaved reinforced cellular concrete floor and Jan 2017 1 S

roof slabs ― Specification (first revision)

126
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

13 IS 6408 (Part 1):1990 Recommendations for modular co-ordination in Mar 2021 T

building industry: Tolerances: Part 1 Glossary of
terms (first revision)

14 IS 6408 (Part 2):1992 Recommendations for modular co-ordination in Mar 2021 C

building industry: Tolerances Part 2 Principles and
applications (first revision)

15 IS 6820:1987 Recommendations for modular co-ordination in Oct 2018 C

building industry: Applications (first revision)

16 IS 7564 (Part 1):1974 Recommendations for co-ordination of dimensions Oct 2018 C

in buildings – Arrangement of building components
and assemblies: Part 1 Functional Group 1
Structures

17 IS 7564 (Part 2):1974 Recommendations for co-ordination of dimensions Oct 2018 C

in building – Arrangement of buildings components
and assemblies: Part 2 Functional Group 2
External envelope

18 IS 7564 (Part 3):1974 Recommendations for co-ordination of dimensions Oct 2018 C

in buildings – Arrangement of building components
and assemblies: Part 3 Functional Group 3
Internal subdivision

19 IS 7564 (Part 4):1975 Recommendations for co-ordination of dimensions Oct 2018 C

in buildings – Arrangement of building components
and assemblies: Part 4 Functional Group 4
Services and drainage

20 IS 7564 (Part 5):1974 Recommendations for co-ordination of dimensions Oct 2018 C

in buildings – Arrangement of building components
and assemblies: Part 5 Functional Group 5
Fixtures, furniture and equipment

21 IS 7921:1987 Recommendations for modular co-ordination in Apr 2019 C

building industry: Horizontal co-ordination
(first revision)

22 IS 7922:1987 Recommendations for modular co-ordination in Oct 2018 C

building industry: Vertical co-ordination
(first revision)

23 IS 7973:1976 Code of practice for architectural and building Jan 2017 C

working drawings

24 IS 8338:1976 Recommendations relating to primary elements in Apr 2019 C

the design of school library buildings

25 IS 8888:2020 Requirements of low income housing for urban C

areas  Guide (second revision)

26 IS 10297:1982 Code of practice for design and construction of Oct 2018 2 C

floors and roofs using precast
reinforced/prestressed concrete ribbed or cored
slabs units

127
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

27 IS 10316:1986 Recommendations for modular co-ordination: Mar 2021 C

Basic module and sub-modular increments

28 IS 10505:1983 Code of practice for construction of floors and Oct 2018 1 C

roofs using precast concrete waffle units

29 IS 10600:1983 Recommendations for modular co-ordination ― Mar 2021 C

/ ISO 2848-74 principles and rules

30 IS 11447:1985 Code of practice for construction with large panel Oct 2018 1 C
prefabricates

31 IS 11775:1986 Recommendations for modular co-ordination: Mar 2021 C

notations and symbols for modular drawings

32 IS 12073:1987 Recommendations for modular co-ordination: Co- Oct 2018 C

ordinating sizes for doorsets and windowsets

33 IS 13612 (Part 1):1993 Modular co-ordination for normal brickwork ― Oct 2018 C
Recommendation: Part 1 Burnt clay bricks

34 IS 13613:1992 Recommendations for modular co-ordination in Oct 2018 C

building industry: Location of structural walls and
floor slabs

35 IS 13727:2020 Requirements of cluster planning for housing ― C

Guide (first revision)

36 IS 13990:1994 Precast reinforced concrete planks and joists for Apr 2019 S
roofing and flooring ― Specification

37 IS 13994:1994 Design and construction of floor and roof with Apr 2019 C
precast reinforced concrete planks and joists ―
Code of practice

38 IS 14142:1994 Design and construction of floors and roofs with Apr 2019 C
prefabricated brick panel ― Code of practice

39 IS 14143:1994 Prefabricated brick panel and partially precast Apr 2019 S

concrete joist for flooring and roofing ―
Specification

40 IS 14201:1994 Precast reinforced concrete channel units for Apr 2019 S

construction of floors and roofs ― Specification

41 IS 14213:1994 Construction of walls using precast concrete stone Apr 2019 C

masonry blocks ― Code of practice

42 IS 14215:1994 Design and construction of floors and roofs with Apr 2019 C
precast reinforced concrete channel units ― Code
of practice

43 IS 14241:1995 Precast reinforced concrete L-panel for roofing ― Apr 2019 S

Specification

44 IS 14242:1995 Design and construction of roof using precast Apr 2019 C

reinforced concrete L-Panel units

128
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

45 IS 15916:2020 Building design and erection using prefabricated C

concrete ― Code of practice (first revision)

46 IS 15917:2020 Building design and erection using C

mixed/composite construction ― Code of practice
(first revision)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

129
CED 53 CEMENT MATRIX PRODUCTS
SCOPE STANDARDIZATION IN THE FIELD OF PRECAST CONCRETE PRODUCTS, CONCRETE PIPES,
CONCRETE POLES AND FIBRE REINFORCED CEMENT PRODUCTS

LIAISON ISO/TC 77 (O) PRODUCTS IN FIBRE REINFORCED CEMENT

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 458:2021 Precast concrete pipes (with and without S

reinforcement) ― Specification (fifth revision)

2 IS 459:1992 Corrugated and semi-corrugated asbestos cement Jan 2018 4 S

sheets ― Specification (third revision)

3 IS 783:1985 Code of practice for laying of concrete pipes Jan 2017 3 C

(first revision)

4 IS 784:2019 Prestressed concrete pipes (including specials) ― S

Specification (third revision)

5 IS 785:1998 Reinforced concrete poles for overhead power Nov 2019 S

and telecommunication lines ― Specification
(second revision)

6 IS 1332:1986 Specification for precast reinforced concrete street Aug 2020 S

lighting poles (first revision)

7 IS 1592:2003 Asbestos cement pressure pipes and joints ― Nov 2018 3 S

Specification (fourth revision)

8 IS 1626 (Part 1):1994 Asbestos cement building pipes and pipe fittings, Aug 2020 S
gutters and gutter fittings and roofing fittings ―
Specification: Part 1 Pipe and pipe fittings
(second revision)

9 IS 1626 (Part 2):1994 Asbestos cement building pipes and pipe fittings, Aug 2020 1 S
gutters and gutter fittings and roofing fittings ―
Specification: Part 2 Gutter and gutter fittings
(second revision)

10 IS 1626 (Part 3):1994 Asbestos cement building pipes and pipe fittings, Aug 2020 S
gutter and gutter fittings and roofing fittings:
Part 3 Roofing fittings (second revision)

11 IS 1678:1998 Prestressed concrete poles for overhead power, Nov 2018 S

traction and telecommunication lines ―
Specification (second revision)

12 IS 1916:2018 Steel cylinder pipes with concrete lining and S

coating ― Specification (second revision)

13 IS 2096:1992 Asbestos cement flat sheets ― Specification Jan 2017 1 S

(first revision)

130
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

14 IS 2098:1997 Asbestos cement building boards ― Specification Jan 2017 S

(first revision)

15 IS 2174:1962 Specification for reinforced concrete dust bins Jan 2018 S

16 IS 2185 (Part 1):2005 Concrete masonry units ― Specification: Aug 2020 S

Part 1 Hollow and solid concrete blocks
(third revision)

17 IS 2185 (Part 2):1983 Specification for concrete masonry units: Aug 2020 S
Part 2 Hollow and solid lightweight concrete
blocks (first revision) (superseding IS 3590)

18 IS 2185 (Part 3):1984 Specification for concrete masonry units: Aug 2020 1 S
Part 3 Autoclaved cellular (Aerated) concrete
blocks (first revision) (Superseding IS 5482)

19 IS 2185 (Part 4):2008 Concrete masonry units ― Specification: Cellular Dec 2019 S
preformed foam concrete blocks

20 IS 2193:1986 Specification for precast prestressed concrete Jan 2017 S

street lighting poles (first revision)

21 IS 2572:2005 Construction of hollow and solid concrete block Aug 2020 C

masonry ― Code of practice (first revision)

22 IS 2905:1989 Concrete poles for overhead power and Jan 2017 M

telecommunication lines ― Methods of test
(first revision)

23 IS 3007 (Part 1):1999 Laying of asbestos cement sheets ― Code of Nov 2019 C
practice: Part 1 Corrugated sheets (first revision)

24 IS 3007 (Part 2):1999 Laying of asbestos cement sheets ― Code of Nov 2019 C
practice: Part 2 Semi-corrugated sheets
(first revision)

25 IS 3597:1998 Concrete pipes ― Methods of test Nov 2018 3 M

(second revision)

26 IS 3632:1969 Method of test for determination of wet volume of Jan 2017 M

asbestos fibre

27 IS 4350:1967 Specification for concrete porous pipes for under Jan 2017 S
drainage

28 IS 4844:1968 Method of sampling and preparation of asbestos Jan 2017 M

fibre for laboratory test purposes

29 IS 4996:1984 Specification for reinforced concrete fence posts Aug 2020 S

(first revision)
30 IS 5328:1969 Method of test for determination of chemical Jan 2017 M
composition of asbestos fibre
31 IS 5748:1969 Methods of test for tensile strength of asbestos Aug 2020 M
fibre

131
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

32 IS 5751:1984 Specification for precast concrete coping blocks Jan 2017 S

(first revision)

33 IS 5758:2020 Precast concrete kerbs, channels, edgings, S

quadrants and other associated fittings ―
Specification (second revision)

34 *IS 5820:1970 Specification for precast concrete cable cover Jan 2017 S

35 IS 5913:2003 Asbestos cement products ― Methods of test Nov 2018 M

(second revision)

36 IS 6041:1985 Code of practice for construction of autoclaved Aug 2020 C

cellular concrete block masonry (first revision)

37 IS 6042:1969 Code of practice for construction of lightweight Aug 2020 C

concrete block masonry

38 IS 6441 (Part 1):1972 Methods of test for autoclaved cellular concrete Jan 2017 M
products: Part 1 Determination of unit weight or
bulk density and moisture content

39 IS 6441 (Part 2):1972 Methods of test for autoclaved cellular concrete Jan 2017 M
products: Part 2 Determination of drying
shrinkage

40 IS 6441 (Part 4):1972 Methods of test for autoclaved cellular concrete Jan 2017 M
products: Part 4 Corrosion protection of steel
reinforcement in autoclaved cellular concrete

41 IS 6441 (Part 5):1972 Methods of test for autoclaved cellular concrete Jan 2017 M
products: Part 5 Determination of compressive
strength

42 IS 6441 (Part 6):1973 Methods of tests for autoclaved cellular concrete Jan 2017 M
products: Part 6 Strength, deformation and
cracking of flexural members subject to bending-
short duration loading test

43 IS 6441 (Part 7):1973 Methods of tests for autoclaved cellular concrete Jan 2017 M
products: Part 7 Strength, deformation and
cracking of flexural members subject to bending-
sustained loading test

44 IS 6441 (Part 8):1973 Methods of tests for autoclaved cellular concrete Jan 2017 M
products: Part 8 Loading tests for flexural
members in diagonal tension

45 IS 6441 (Part 9):1973 Methods of tests for autoclaved cellular concrete Jan 2017 M
products: Part 9 Jointing of autoclaved cellular
concrete elements

46 IS 6523:1983 Specification for precast reinforced concrete door Jan 2018 2 S

and window frames (first revision)

47 IS 6530:1972 Code of practice for laying of asbestos cement Jan 2017 1 C

pressure pipes

132
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

48 IS 6908:1991 Asbestos-cement pipes and fittings for sewerage Jan 2017 1 S

and drainage ― Specification (first revision)

49 IS 7319:1974 Specification for perforated concrete pipes Aug 2020 S

50 IS 7321:1974 Code of practice for selection, handling and Aug 2020 C

erection of concrete poles for overhead power and
telecommunication lines

51 IS 7322:1985 Specification for specials for steel cylinder Aug 2020 S

reinforced concrete pipes (first revision)

52 IS 7639:1975 Methods of sampling of asbestos cement products Nov 2019 M

53 IS 8870:1978 Specification for asbestos cement cable conduits Jan 2017 S

and troughs

54 IS 9375:1979 Specification for precast reinforced concrete plant Jan 2017 S

guards

55 IS 9627:1980 Specification for asbestos cement pressure pipes Aug 2020 S

(light duty)

56 IS 9690:1980 Method of test for determination of openness or Jan 2017 M

fibrization of chrysotile asbestos fibre by air
permeability method using Dyckerhoff apparatus

57 IS 9691:1980 Method of test for length distribution (wet Jan 2017 M

classification of fibre length) of chrysotile asbestos
fibre using Bauer Mcnett classifier

58 IS 9745:1981 Method for determining strength giving properties Jan 2017 M

of asbestos fibre

59 IS 9872:1981 Specification for precast concrete septic tanks Jan 2017 S

60 IS 9893:1981 Specification for precast concrete lintels and sills Jan 2017 1 S

61 IS 11267:1985 Method of test for length distribution (wet Aug 2020 M

classification of fibre length) of chrysotile asbestos
fibre using Turner and Newall classifier

62 IS 11275:1985 Method of test for determination of crudiness and Aug 2020 M

grit content of asbestos fibre

63 IS 11276:1985 Method of test for determination of openness or Aug 2020 M

fiberization of chrysotile asbestos fibre by air
permeability method using rapid surface area
apparatus

64 IS 11450:2006 Method for determination of airborne asbestos Jul 2016 M

fibre concentration in work environment by light
microscopy (membrane filter method)
(first revision)

65 IS 11451:1986 Recommendations for safety and health Aug 2020 1 SS

requirements relating to occupational exposure to
asbestos

133
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

66 IS 11707:1986 Glossary of terms relating to asbestos Aug 2020 T

67 IS 11767:2005 Recommendations for cleaning of premises and Aug 2020 SS

plants using asbestos fibres (first revision)

68 IS 11768:1986 Recommendations for disposal of asbestos waste Aug 2020 1 SS

material

69 IS 11769 (Part 1):1987 Guidelines for safe use of products containing Jan 2017 1 SS
asbestos: Part 1 Asbestos cement products

70 IS 11769 (Part 2):2005 Guidelines for safe use of products containing Feb 2021 SS
asbestos: Part 2 Friction materials (first revision)

71 IS 11769 (Part 3):1986 Guidelines for safe use of products containing Aug 2020 SS
asbestos: Part 3 Non-cement asbestos products
other than friction materials

72 IS 11770 (Part 1):1987 Recommendations for control of emission of Jan 2017 1 SS

asbestos dust in premises manufacturing products
containing asbestos: Part 1 Asbestos cement
products

73 IS 11770 (Part 2):2006 Recommendations for control of emission of Mar 2021 SS

asbestos dust in premises manufacturing products
containing asbestos: Part 2 Friction materials
(first revision)

74 IS 11770 (Part 3):1987 Recommendations for control of emission of Jan 2017 SS

asbestos dust in premises manufacturing products
containing asbestos: Part 3 Non-cement asbestos
products other than friction materials

75 IS 12078:1987 Recommendations for personal protection of Jan 2017 2 SS

workers engaged in handling asbestos

76 IS 12079:1987 Recommendations for packaging, transport and Jan 2017 SS

storage of asbestos

77 IS 12080:1987 Recommendations for local exhaust ventilation Jan 2017 SS

systems in premises manufacturing products
containing asbestos

78 IS 12081 (Part 1):1987 Recommendations for pictorial warning signs and Jan 2017 1 SS
precautionary notices for asbestos and products
containing asbestos: Part 1 Workplaces

79 IS 12081 (Part 2):1987 Recommendations for pictorial warning signs and Jan 2017 1 SS
precautionary notices for asbestos and products
containing asbestos: Part 2 Asbestos and its
products

80 IS 12082 (Part 1):2006 Control of asbestos emission ― Feb 2021 SS

Recommendations: Part 1 Mining of asbestos ore
(first revision)

81 IS 12082 (Part 2):2006 Control of asbestos emission ― Feb 2021 SS

Recommendations: Part 2 Milling of asbestos ore
(first revision)

134
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

82 IS 12440:1988 Specification for precast concrete stone masonry Aug 2020 S

blocks

83 IS 12592:2002 Precast concrete manhole cover and frame ― Jan 2018 2 S

Specification (first revision)

84 IS 13000:1990 Silica-asbestos-cement flat sheets ― Specification Aug 2020 1 S

85 IS 13008:1990 Shallow corrugated asbestos cement sheets ― Aug 2020 1 S

Specification

86 IS 13158:1991 Prestressed concrete circular spun poles for Jan 2017 S

overhead power, traction and telecommunication
lines ― Specification

87 IS 13356:1992 Precast ferrocement water tanks Up to 10000 Jan 2017 S

litres capacity ― Specification

88 IS 14862:2000 Fibre cement flat sheets ― Specification Aug 2020 3 S

89 IS 14871:2000 Products in fibre reinforced cement - long Aug 2020 2 S

corrugated or asymmetrical section sheets and
fittings for roofing and cladding ― Specification

90 IS 15155:2020 Bar/wire wrapped steel cylinder pipes with mortar S

lining and coating (including specials) ―
Specification (first revision)

91 IS 16720:2018 Pulverized fuel ash-cement bricks ― Specification S

92 IS 17452:2020 Use of alkali activated concrete for precast C

products ― Guidelines

DRAFTS FINALIZED BUT NOT YET UNDER PUBLICATION

1 DOC:CED 53 (14917) Draft Indian Standard Fibre cement sheet - lightweight concrete sandwich panels
― Specification

2 DOC:CED 53 (16195) Draft Indian Standard Precast concrete cable cover (first revision of IS 5820)

3 DOC:CED 53 (16891) Draft Indian Standard Precast Concrete Circular Manhole ― Specification

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

135
CED 54 CONCRETE REINFORCEMENT
SCOPE STANDARDIZATION IN THE FIELD OF REINFORCEMENT FORCONCRETE INCLUDING PRE-
STRESSING STEEL

LIAISON ISO/TC 17/SC 16 (O) STEEL FOR THE REINFORCEMENT AND PRESTRESSING OF CONCRETE

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 432 (Part 1):1982 Specification for mild steel and medium tensile May 2020 2 S
steel bars and hard-drawn steel wire for concrete
reinforcement: Part 1 Mild steel and medium
tensile steel bars (third revision)

2 IS 432 (Part 2):1982 Specification for mild steel and medium tensile May 2020 3 S
steel bars and hard-drawn steel wire for concrete
reinforcement: Part 2 Hard-drawn steel wire
(third revision)

3 IS 1566:1982 Specification for hard-drawn steel wire fabric for May 2020 4 S
concrete reinforcement (second revision)

4 IS 1785 (Part 1):1983 Specification for plain hard-drawn steel wire for Jan 2018 4 S
prestressed concrete: Part 1 Cold-drawn stress
relieved wire (second revision)

5 IS 1785 (Part 2):1983 Specification for plain hard-drawn steel wire for Jan 2018 4 S
prestressed concrete: Part 2 As-drawn wire
(first revision)

6 IS 1786:2008 High strength deformed steel bars and wires for Jan 2018 4 S
concrete reinforcement ― Specification
(fourth revision) (superseding IS 1139:1966)

7 IS 2090:1983 Specification for high tensile steel bars used in May 2020 1 S
prestressed concrete (first revision)

8 IS 6003:2010 Indented wire for prestressed concrete ― Mar 2021 S

Specification

9 IS 6006:2014 Uncoated stress relieved strand for prestressed Mar 2019 S

concrete ― Specification (second revision)

10 IS 9417:2018 Welding of high strength steel bars for reinforced C

concrete construction — Recommendations
(second revision)

11 IS 10790 (Part 1):1984 Methods of sampling of steel for prestressed and Mar 2021 M
reinforced concrete: Part 1 Prestressing steel

12 IS 10790 (Part 2):1984 Methods of sampling of steel for prestressed and Mar 2021 M
reinforced concrete: Part 2 Reinforcing steel

13 IS 13620:1993 Fusion bonded epoxy coated reinforcing bars ― May 2020 1 S

Specification

136
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

14 *IS 14268:2017 Uncoated stress relieved low relaxation seven S

wire (ply) strand for prestressed concrete ―
Specification (first revision)

15 IS 16172:2014 Reinforcement couplers for mechanical splices of Mar 2019 1 S

bars in concrete ― Specification

16 IS 16651:2017 High strength deformed stainless steel bars and S

wires for concrete reinforcement ― Specification

17 IS 16644:2018 Stress-relieved low relaxation steel wire for S

prestressed concrete ― Specification

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 54 (14912) Draft Indian Standard Uncoated stress relieved low relaxation seven-wire (ply)
strand for prestressed concrete — Specification (second revision of IS 14268)

DRAFT STANDARDS FORMULATED

1 DOC:CED 54 (14913) Draft Indian Standard Cold-reduced steel wire for the manufacture of welded fabric
for concrete reinforcement — Specification

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

137
CED 55 SIEVES, SIEVING AND OTHER SIZING METHODS
SCOPE STANDARDIZATION PERTAINING TO SIZE, CLASSIFICATION FOR SOLID PARTICULATE
MATERIALS INCLUDING METHODS AND METHODS OF TEST, EQUIPMENT AND MATERIALS
OF EQUIPMENT

LIAISON ISO/TC 24 (O) PARTICLE CHARACTERIZATION INCLUDING SIEVING

ISO/TC 24/SC 4 (O) PARTICLE CHARACETRIZATION
ISO/TC 24/SC 8 (P) TEST SIEVES, SIEVING AND INDUSTRIAL SCREENS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 460 (Part 1):2020 Test sieves  Specification: Part 1 Wire cloth test S
sieves (fourth revision)

2 IS 460 (Part 2):2020 Test sieves  Specification: Part 2 Perforated plate S

test sieves (fourth revision)

3 IS 460 (Part 3):2020 Test sieves  Specification: Part 3 Methods of S

examination of apertures of test sieves
(fourth revision)

4 IS 1568:1970 Specification for wire cloth for general purposes Jun 2018 1 S
(first revision)

5 IS 1607:2013 Methods of test sieving (second revision) Mar 2018 M

6 *IS 2405 (Part 1):1980 Specification for industrial sieves: Part 1 Wire cloth Dec 2016 S
sieves (first revision)

7 *IS 2405 (Part 2):1980 Specification for industrial sieves: Part 2 Perforated Jun 2018 1 S
plates (first revision)

8 IS 3150:1982 Specification for hexagonal wire netting for general Jun 2018 1 S
purposes (second revision)

9 IS 4124:1981 Glossary of terms relating to powders (first revision) Jan 2020 T

10 IS 4879:1968 Method of sub-division of gross sample of powder Jan 2020 M

used for determination of particle size

11 IS 4961:1968 Determination of particle size of powders by air Jan 2020 M

elutriation methods

12 IS 5257:1969 Specification for eyepiece and screen graticule for Jan 2020 S
determination of particle size of powders

13 IS 5258:1969 Determination of particle size of powders by optical Jan 2020 M

microscope method

14 IS 5282:1969 Liquid sedimentation methods for determination of Jan 2020 M

particle size of powders

15 IS 5421:2013 Glossary of terms relating to test sieves and test Feb 2018 T
sieving (second revision)

138
SI IS Number/ DOC Title Reaffirm No. of Aspect
No. Number Date Amd.

16 IS 5742 (Part 1):1970 Terms and symbols for sieve bottoms: Dec 2016 T
Part 1 Woven and welded wire screens

17 IS 5742 (Part 2):1970 Terms and symbols for sieve bottoms: Jun 2018 T
Part 2 Perforated plates

18 IS 10483:1983 Code for designating perforations of industrial plate Jun 2020 C

sieves

FINALIZED DRAFTS UNDER PUBLICATION

1 DOC:CED 55 (15740) Draft Indian Standard Industrial sieves – Specification: Part 1 Wire cloth sieves
[second revision of IS 2405 (Part 1)]

2 DOC:CED 55 (15741) Draft Indian Standard Industrial sieves – Specification: Part 2 Perforated plates
[second revision of IS 2405 (Part 2)]

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

139
CED 56 HILL AREA DEVELOPMENT ENGINEERING
SCOPE STANDARDIZATION IN THE FIELD OF DEVELOPMENTAL ACTIVITIES OF HILLY AREAS SUCH
AS LANDSLIDE ANALYSIS, SITE EVALUATION FOR HUMAN SETTLEMENT, SAFE DESIGN,
SELECTION OF BUILDING MATERIALS AND MODES OF CONSTRUCTION SUITABLE FOR HILLY
AREAS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 14458 (Part 1):1998 Retaining wall for hill area ― Guidelines: Sep 2017 C
Part 1 Selection of type of wall

2 IS 14458 (Part 2):1997 Retaining wall for hill area ― Guidelines: Sep 2017 C
Part 2 Design of retaining/breast walls

3 IS 14458 (Part 3):1998 Retaining wall for hill area ― Guidelines: Sep 2017 C
Part 3 Construction of dry stone walls

4 IS 14458 (Part 4):2018 Retaining wall for hill area ― Guidelines: C

Part 4 Construction of banded dry stone masonry
walls

5 IS 14458 (Part 5):2018 Retaining wall for hill area ― Guidelines: C

Part 5 Construction of cement stone masonry walls

6 IS 14458 (Part 6):2020 Retaining wall for hill area — Guidelines: C

Part 6 Construction of gabion walls

7 IS 14496 (Part 1):2020 Preparation of landslide hazard zonation maps in C

mountainous terrains ― Guidelines: Part 1 Meso-
zonation

8 IS 14496 (Part 2):1998 Preparation of landslide hazard zonation maps in Sep 2017 1 C
mountainous terrains ― Guidelines: Part 2 Macro-
zonation

9 IS 14680:1999 Landslide control ― Guidelines Sep 2019 C

10 IS 14804:2000 Siting design and selection of materials for Sep 2017 C

residential buildings in hilly areas ― Guidelines

11 IS 14961:2001 Guidelines for rainwater harvesting in hilly areas by Sep 2017 C

roof water collection system

12 IS 17162:2020 Draft Indian Standard preparation of landslide risk C

assessment maps in mountainous terrains ―
Guidelines

13 IS 17163:2020 Site specific investigation and stability analysis of C

landslides ― Guidelines

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

140
CED 57 CYCLONE RESISTANT STRUCTURES
SCOPE FORMULATION OF INDIAN STANDARDS, RECOMMENDATIONS AND GUIDELINES ON
PLANNING, DESIGN AND CONSTRUCTION OF CYCLONE RESISTANT STRUCTURES AND
BUILDINGS, PROTECTION FROM HIGH SPEED WINDS, WARNING FROM CYCLONES AND TIDAL
WAVES AND POST CYCLONE REHABILITATION MEASURES

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

STANDARDS PUBLISHED

1 IS 15498:2004 Guidelines for improving the cyclonic resistance of Jan 2020 C

low rise houses and other buildings/structures

2 IS 15499:2004 Guidelines for survey of housing and building Jan 2020 C

typology in cyclone prone areas for assessment of
vulnerability of regions and post cyclone damage
estimation

3 IS 17164:2020 Draft Indian Standard design and construction of C

cyclone shelters ― Guidelines

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

141
CED 58 SUSTAINABILITY OF BUILT ENVIRONMENT SECTIONAL COMMITTEE
SCOPE STANDARDIZATION IN THE AREA OF SUSTAINABILITY OF BUILT ENVIRONMENT

LIAISON ISO/TC 59/SC 17 (O) SUSTAINABILITY IN BUILDINGS AND CIVIL ENGINEERING WORKS

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

1 IS/ISO 15392:2019 Sustainability in buildings and civil engineering O

works ― General principles (first revision)

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

142
CED 59 SMART CITIES SECTIONAL COMMITTEE
SCOPE STANDARDIZATION IN THE FIELD OF SMART CITIES TERMINOLOGY, COMPONENTS,
PLANNING, DESIGN, INTEGRATION, IMPLEMENTATION, OPERATION, MAINTENANCE AND
ASSESSMENT

LIAISON ISO/TC 268 (P) SUSTAINABLE CITIES AND COMMUNITIES

ISO/TC 268/SC 1 (P) SMART COMMUNITY INFRASTRUCTURES

SI IS Number/ DOC Title Reaffirm No. of Aspect

No. Number Date Amd.

1 IS 17000:2019 Sustainable development of habitats — Indicators O

2 IS 17451:2020 Smart community infrastructure — Best practices C

for transportation — Guidelines

3 IS 17456:2020 Smart community infrastructure — Guidance on C

smart transportation for allocation of parking lots of
cities

4 IS 17457:2020 Sustainable development of habitats — T

Vocabulary

* INDICATES STANDARDS UNDER REVISION / INDICATES ADOPTION OF ISO STANDARD

143
 ANNEX I
STANDARDS WITHDRAWN/SUPERSEDED

SI IS Number/ DOC Title

No. Number

1 IS 515:1959 Specification for natural and manufactured aggregates for use in mass concrete
(Superseded by 383)

2 IS 773:1988 Specification for enamelled cast iron water-closets railway coaching stock type
(fourth revision)

3 IS 775:1970 Specification for cast iron brackets and supports for wash basins and sinks
(second revision)

4 IS 776:1962 Specification for wooden water closet seats and covers (revised)

5 IS 777:1988 Specification for glazed earthenware wall tiles (second revision)

6 IS 780:1984 Sluice valves for water works purposes (50 to 300 mm size)

7 IS 849:1994 Specification for cold setting case in glue for wood (first revision)

8 IS 850:1994 Specification for natural sour (lactic) casein for glue manufacture (first revision)

9 IS 929:1959 Specification for hook ladder for fire fighting purposes (withdrawn)

10 IS 930:1977 Specification for wooden extension ladders for fire brigade use (first revision)

11 IS 931:1973 Specification for wheeled fire escape (first revision)

12 IS 932:1960 30-40 M (or 100-110 ft) Mechanically operated turn-table ladder for fire brigade
use (withdrawn)

13 IS 933:1988 Specification for portable chemical foam fire extinguisher (third revision)

14 IS 934:1988 Specification for portable fire extinguisher water type (soda acid) (fourth revision)

15 IS 935:1967 Specification for portable chemical fire extinguisher, carbon tetrachloride type
(first revision) (withdrawn)

16 IS 936:1966 Specification for underground fire hydrant, double valve type (revised)
(withdrawn) (see IS 909)

17 IS 938:1973 Functional requirements for 1350-1/min small fire engine (second revision)
(Superseded by IS 2696)

18 IS 940:2003 Specification for portable fire extinguisher, water type (gas cartridge)
(fourth revision)

19 IS 945:1966 Specification for 1800-1/min motor fire engine (first revision) (Superseded by
IS 946)

20 IS 946:1977 Functional requirements for motor fire engine (first revision)

21 IS 953:1960 Specification for small foam crash tender (withdrawn)

22 IS 954:1989 Functional requirements for carbon dioxide tender for fire brigade use
(second revision)

23 IS 1139:1966 Specification for hot rolled mild steel, medium tensile steel and high yield strength
steel deformed bars for concrete reinforcements (revised) (Superseded by
IS 1786)

144
SI IS Number/ DOC Title
No. Number

24 IS 1200 (Part 17):1985 Method of measurement of building and civil engineering works: Part 17 Road
work including air field pavements (third revision)

25 IS 1233:1969 Recommendations for modular co-ordination of dimensions in the building

industry (first revision) (Superseded by IS 6820)

26 IS 1256:1967 Code of practice for building byelaws

27 IS 1298:1958 Methods of test for determination of free lime in Portland cement (Superseded by
IS 4032)

28 IS 1329:1975 Specification for aircraft timber (Baulks and scantlings) (first revision)

29 IS 1625:1971 Code of practice for preparation of lime mortar for use in buildings (first revision)
(Superseded by IS 2250)

30 IS 1629:1960 Rules for grading of cut sizes of timber (Superseded by IS 1331:1971)

31 IS 1645:1960 Code of practice for fire safety of buildings (Superseded by IS 1642)

32 IS 1647:1960 Code of practice for fire safety of buildings

33 IS 1648:1961 Code of practice for fire safety of building (general): Fire fighting equipment and
its maintenance

34 IS 1700:1973 Specification for drinking fountains (first revision)

35 IS 1728:1960 Specification for sheet metal rain-water pipes upto 100mm nominal size, gutters,
fittings and accessories

36 IS 1731:1971 Dimensions for steel flats for structural and general engineering

37 IS 1826:1983 Specification for venetian blinds for windows

38 IS 1849(Part 2):1977 Guide for design and installation of vertical mixed-feed type lime kiln: Part 2 For
limeshell (first revision)

39 IS 1861(Part 2):1977 Guide for manufacture of lime in vertical mixed-feed type kiln: Part 2 From
limeshell (first revision)

40 IS 1910:1961 Specification for self contained breathing apparatus for the brigade use
[ Incorporated in IS 10245 (Part 2)]

41 IS 1911:1967 Schedule of unit weight of building materials (first revision)

42 IS 1915 : 1961 Code of Practice for Steel Bridge

43 IS 1924:1973 Specification for portable fire extinguisher, water type (pocket pump)
(first revision) (withdrawn)

44 IS 1933:1961 Specification for portable chemical fire extinguisher chloro bromomethane type
(withdrawn)

45 IS 2104:1981 Specification for water meter boxes (domestic type) (first revision)

46 IS 2171:1999 Specification for portable fire extinguishers, dry powder (cartridge type)
(fourth revision)

145
SI IS Number/ DOC Title
No. Number

47 IS 2178:1962 Specification for timber for use in aircraft propeller construction

48 IS 2184:1962 Tables for volume of round timber logs (withdrawn)

49 IS 2217:1982 Recommendations for providing first-aid fire fighting arrangement in public

building (first revision) (withdrawn)

50 IS 2298:1977 Specification for single-barrel stirrup pump for fire fighting purposes
(second revision)

51 IS 2299:1968 Specification for steel helmets for civil defence (first revision) (Superseded by
IS 2745:1983)

52 IS 2300:1968 Specification for non metal helmets for civil defence (first revision) (Superseded
by IS 2745)

53 IS 2332:1972 Nomenclature of floor and storeys (first revision) (Superseded by IS 962:1967)

54 IS 2375:1963 Recommendation for modular co-ordination applied to RCC framed structures

(Superseded by IS 6772)

55 IS 2401:1973 Code of practice for selection, installation and maintenance of domestic water
meters (first revision)

56 IS 2406:1963 Code of practice for fire safety of non-industrial buildings (withdrawn)

57 IS 2556 (Part 10):1974 Specification for vitreous sanitary appliances (vitreous china): Part 10 Specific
requirements of foot rests (second revision)

58 IS 2556 (Part 11):1979 Specification for vitreous sanitary appliances (vitreous china): Part 11 Specific
requirements for shower rose (first revision)

59 IS 2556 (Part 12):1973 Specification for vitreous sanitary appliances (vitreous china): Part 12 Specific
requirements of floor traps

60 IS 2556 (Part 13):1973 Specification for vitreous sanitary appliances (vitreous china): Part 13 Specific
requirements of traps for squatting pans

61 IS 2718:1964 Recommendations for preferred dimensions for storey heights (superseded by

IS 7922)

62 IS 2720 (Part 32):1970 Specification for north dakota cone test

63 IS 2878 Specification for fire extinguisher, carbon dioxide type (portable and trolley
mounted) (third revision)

64 IS 2906:1984 Sluice valves for water works purposes (350 to 1200 mm size)

65 IS 3076:1985 Specification for low density polyethylene pipes for potable water supplies
(second revision)

66 IS 3102:1971 Classification of burnt clay solid bricks (first revision) (Superseded by IS 1077)

67 IS 3311:1979 Specification for waste plug and its accessories for sinks and wash-basins
(first revision) (Superseded by IS 2693)

68 IS 3385 (Part 1):1965 Code of practice for measurement of civil engineering works: Part 1 Pile
foundations [Superseded by IS 1200 (Part XXIII)]

146
SI IS Number/ DOC Title
No. Number

69 IS 3463:1966 Specification for polystyrene wall tiles

70 IS 3489:1985 Specification for enamelled steel bath tubs (first revision)

71 IS 3590:1966 Specification for load bearing light weight concrete blocks [Superseded by
IS 2185 (Part 2)]

72 IS 3805:1979 Specification for pent-top wooden cases (first revision)

73 IS 3955:1967 Code of practice for design and construction of well foundations

74 IS 4112:1967 Code of practice for fixing of polystyrene wall tiles

75 IS 4212:1978 Specification for drafting/reference tables for drawing offices (first revision)

76 IS 4435:1967 Specification for wooden ladders and trestles

77 IS 4805:1978 Guide for construction of brick kiln (first revision)

78 IS 4838 (Part 1):1969 Anthropometric dimensions for school children: Part 1 Age group 5-11 years
(Superseded by IS 4838:1990)

79 IS 4838 (Part 2):1979 Anthropometric dimensions for school children: Part 2 Age group 12-16 years
(first revision) (Superseded by IS 4838:1990)

80 IS 4861:1984 Specification for dry powder for fighting fires in burning metals (first revision)

81 IS 4962:1968 Specification for wooden side sliding doors

82 IS 5248:1988 Specification for teak logs for production of sliced veneers (first revision)

83 IS 5417:1969 Specification for pencil tray (wooden) for use in office

84 IS 5418:1969 Specification for wood folding drawing tables

85 IS 5419:1969 Specification for wooden scribing table

86 IS 5434:1969 Specification for non-ferrous alloy bottle traps for marine use

87 IS 5482:1969 Autoclaved cellular concrete blocks [Superseded by IS 2185(Part 3):1984]

88 IS 5490 (Part 1):1977 Specification for refills for portable fire extinguishers and chemical fire engines:
Part 1 For soda acid portable fire extinguishers (first revision)

89 IS 5490 (Part 2):1977 Specification for refills for portable fire extinguishers and chemical fire engines:
Part 2 For foam type portable fire extinguishers (first revision)

90 IS 5490 (Part 3):1979 Specification for refills for portable fire extinguishers and chemical fire engines:
Part 3 For soda acid chemical fire engines, 50 litre capacity (first revision)

91 IS 5490 (Part 4):1979 Specification for refills for portable fire extinguishers and chemical fire engines:
Part 4 For foam chemical fire engines, 50 litres capacity (first revision)

92 IS 5498:1969 Specification for lime-cement-cinder hollow concrete blocks (withdrawn)

(Superseded by IS 3115)

93 IS 5506:1979 Specification for 50-l capacity chemical fire engine, soda acid type (first revision)

147
SI IS Number/ DOC Title
No. Number

94 IS 5507:1979 Specification for 50-l capacity chemical fire engine, foam type (first revision)

95 IS 5869:1970 Specification for pillar taps for marine use

96 IS 5896 (Part 2):1975 Code of practice for selection, operation and maintenance of special firefighting
appliances: Part 2 Escapes

97 IS 5917:1970 Specification for vitreous (vitreous china) wash basins for marine use

98 IS 6234:2003 Specification for portable fire extinguishers, water type (stored pressure)
(second revision)

99 IS 6249:1971 Specification for flush valves and fittings for marine use

100 IS 6251:1971 Specification for shower fittings for marine use

101 IS 6342:1987 Specification for rosewood logs for production of sliced veneers (first revision)

102 IS 6382:1984 Code of practice for design and installation of fixed carbon dioxide for fire
extinguishing system (first revision)

103 IS 6602:1972 Specification for ventilator poles

104 IS 6618:1972 Safety requirements for push chairs

105 IS 6717:1972 Specification for mobile road crane, fully sewing (superseded by IS 457)

106 IS 6772:1972 Recommendations for dimensional co-ordination for industrialized

buildings−Preferred increments

107 IS 7184:1973 Recommendations for modular co-ordination reference lines of horizontal control
lingco-ordinating dimensions [superseded by IS 792]

108 IS 7292:1974 Code of practice for in-situ determination of rock properties by flat jack

109 IS 7508:1974 Specification for wooden writing-cum-dressing table

110 IS 7550:1975 Specification for cane baskets for ration

111 IS 7612:1974 Functional requirements for flame resistant and heat resistant suits

112 IS 7630:1975 Specification for plywood drums

113 IS 8112:2013 Specification for 43 grade ordinary Portland cement (second revision)

114 IS 8149:1994 Functional requirements for twin CO2 fire extinguishers (trolley mounted)
(first revision)

115 IS 8273:2000 Fibrous gypsum plaster boards (first revision)

116 IS 8321:1976 Glossary of terms applicable to plumbing work

117 IS 8358:1977 Performance test for wooden packing cases

118 IS 8403:1977 Code of practice for construction of clarification digester for treatment of sewage
(withdrawn)

119 IS 8718:1978 Specification for vitreous enamelled steel kitchen sinks

148
SI IS Number/ DOC Title
No. Number

120 IS 8719:1978 Specification for vitreous siphonic wash-down water closets for marine

121 IS 8727:1978 Specification for vitreous enamelled steel wash basins

122 IS 8934:1978 Specification for cast copper alloy fancy pillar taps for water services

123 IS 9076:1979 Specification for vitreous integrated squatting pans for marine use

124 IS 10204:2001 Specification for portable fire extinguisher mechanical foam type (first revision)

125 IS 10324:1982 Specification for wooden crates for bottled drinks

126 IS 10474:1983 Specification for 150 litre capacity chemical fire engine, foam type

127 IS 10658:1999 Specification for higher capacity dry powder fire extinguisher (trolley mounted)
(first revision)

128 IS 10785:1983 Method for determination of compressive and tensile strength for point load tests
on rock lumps

129 IS 11070:1984 Specification for bromochlorodifluoromethane (halon-1211) for fire

130 IS 12049:1987 Dimensions and tolerances relating to wood based panel materials

131 IS 12269:2013 Specification for 53 grade ordinary Portland cement (first revision)

132 IS 13027 (Part 1):1990 Methods of test for door leaves: Part 1 Measurement of dimensions and defects
of squareness

133 IS 13027 (Part 2):1991 Methods of test for door leaves: Part 2 Measurement of defects of general
flatness

134 IS 13034:1990 Methods of test for timber panelled and glazed door shutters - type tests

135 IS 13240:1991 Specification for walnut logs for production of sliced veneers

136 IS 13311 (Part 1):1992 Methods of non-destructive testing of concrete: Part 1 Ultrasonic pulse velocity

137 IS 13311 (Part 2):1992 Non-destructive testing of concrete ― Methods of test: Part 2 Rebound hammer

138 IS 13385:1992 Specification for fire extinguisher- 50 litre capacity wheel mounted water type
(Gas cartridge)

139 IS 13386:1992 Specification for fire extinguisher 50 litre capacity mechanical foam type

140 IS 13435 (Part 5):1992 Acrylic based polymer waterproofing material ― Methods of test:
Part 5 Determination of minimum film forming temperature and white point

141 IS 13519:1992 Guidelines for inspection of fixed steel offshore structures during fabrication and
installation

142 IS 13711:1993 Ceramic tiles ― Sampling and basis of acceptance [Superseded by

IS 13630 (Part 15):2006]

143 IS 13746:1993 Code of practice for geotechnical investigation of offshore jacket

144 IS 13753:1993 Specification for dust pressed ceramic tiles with water absorption of E > 10%
Group B III

149
SI IS Number/ DOC Title
No. Number

145 IS 13754:1993 Specification for dust pressed ceramic tiles with water absorption of 6% < E <
10% Group B II b)

146 IS 13755:1993 Specification for dust pressed ceramic tiles with water absorption of
3% < E < 6% Group (B II a)

147 IS 13756:1993 Specification for dust pressed ceramic tiles with water absorption ofE < 3%
Group B I

148 IS 13802:1993 Guidelines for planning and execution of seabed engineering (Geophysical)
survey for offshore platforms and pipelines

149 IS 13849:1993 Specification for portable fire extinguisher dry powder type (stored pressure)

150 IS 14609:1999 Specification for dry chemical powder for fighting ABC Class

151 IS 15397:2003 Specification for portable fire extinguisher mechanical foam type (stored
pressure)

152 IS 15973 (Part 2):2013 Selection and use of various types of lignocellulosic panel products:
Part 2 Hardboard

153 SP 6 (Part 1):1964 Handbook for structural engineers ― Structural steel sections

154 SP 16 (S&T):1980 Design aids for reinforced concrete to IS 456:1978

155 SP 22 (S&T):1982 Explanatory handbook on codes for earthquake engineering (IS 1893:1975 &
IS 4326:1976)

156 SP 6 (Part 2):1962 Handbook for structural engineers ― Steel beams and plate girders

157 SP 6 (Part 3):1962 Handbook for structural engineers ― Steel columns and struts

158 SP 24 (S&T):1983 Explanatory handbook on Indian Standard code of practice for plain and
reinforced concrete (IS 456:1978)

159 SP 10 (S&T):1975 Nomograms for thickness of masonry walls

160 SP 6 (Part 7):1972 Handbook for structural engineers ― Simple welded girders

161 SP 38 (S&T):1987 Handbook on typified designs for structures with steel roof trusses (with and
without cranes) (Based on IS Codes)

162 SP 40 (S&T):1988 Handbook on structures with steel portal frames (without cranes)

163 SP 47 (S&T):1988 Handbook on structures with steel lattic portal frames (without cranes)

150
 ANNEX II

LIST OF INDIAN STANDARDS HARMONIZED WITH ISO/IEC STANDARDS

Sl. IS Number Title ISO/IEC Sectional ISO/TC

No. Number Committee Number
of CED

1 IS 10428:1983 Glossary of terms relating to doors ISO 1804: CED 11 162

/ ISO 1804:1972 1972

2 IS 10600:1983 Recommendations for modular co- ISO 2848: CED 51 59

/ ISO 2848:1974 ordination ― principles and rules 1974

3 IS 10957:1999 Glossary of terms applicable for joints in ISO 2444: CED 13 59

/ ISO 2444:1988 building 1988

4 IS 10958:1984 General check list of functions of joints in ISO 3447: CED 13 59

/ ISO 3447:1975 building 1975

5 IS 10959:2017 Glossary of terms for sealants for ISO 6927: CED 13 59

/ ISO 6927:2012 building purposes (first revision) 2012

6 IS 11050 (Part 1):1984 Rating of sound insulation in buildings ISO 717-1: CED 12 43
/ ISO 717-1:1982 and of building elements: Part 1 Airborne 1982
sound insulation in buildings and of
interior building elements

7 IS 11050 (Part 2):1984 Rating of sound insulation in buildings ISO 717-2: CED 12 43
/ ISO 717-2:1982 and of building elements: Part 2 Impact 1982
sound insulation

8 IS 11050 (Part3):1984 Rating of sound insulation in buildings ISO 717-3: CED 12 43

/ ISO 717-3:1982 and of building elements: Part 3 Airborne 1982
sound insulation of facade

9 IS 11817:1986 Classification of joints in buildings for ISO 7727: CED 13 59

/ ISO 7727:1984 accommodation of dimensional 1984
deviations during construction

10 IS 11818:1986 Method of test for laboratory ISO 6589: CED 13 59

/ ISO 6589:1983 determination of air permeability of joints 1983
in buildings

11 IS 13089:1991 Specification for furniture − storage units ISO 7171: CED 35 136
/ ISO 7171:1988 − determination of stability 1988

12 IS 13735:1993 Specification for audible emergency ISO 8201: CED 12 43

/ ISO 8201:1987 evacuation signal 1987

13 IS 16130:2014 Thermoplastics materials for pipes and ISO 12162: CED 50 138
/ ISO 12162:2009 fittings for pressure applications ― 2009
Classification, designation and design
coefficient

14 IS 16462:2016 Plastics piping and ducting systems ISO 9080: CED 50 138
/ ISO 9080:2012 determination of the long-term 2012
hydrostatic strength of thermoplastics
materials in pipe

151
Sl. IS Number Title ISO/IEC Sectional ISO/TC
No. Number Committee Number
of CED

15 IS 16268:2017 Plastics pipes and fittings combined ― ISO/TR CED 50 138

/ ISO/TR 10358:1993 Chemical resistance classification table 10358:1993

16 IS/ISO 834-1:1999 Fire resistance tests ― Elements of ISO 834-1: CED 36 92

building construction: Part 1 General 1999
requirements

17 IS/ISO 834-4:2000 Fire resistance tests ― Elements of ISO 834-4: CED 36 92

building construction: Part 4 Specific 2000
requirements for load bearing vertical
separating elements

18 IS/ISO 834-5:2000 Fire resistance tests ― Elements of ISO 834-5: CED 36 92

building construction: Part 5 Specific 2000
requirements for load bearing horizontal
separating elements

19 IS/ISO 834-6:2000 Fire resistance tests ― Elements of ISO 834-6: CED 36 92

building construction: Part 6 Specific 2000
requirements for beams

20 IS/ISO 834-7:2000 Fire resistance tests ― Elements of ISO 834-7: CED 36 92

building construction: Part 7 Specific 2000
requirements for columns

21 IS/ISO 834-8:2002 Fire resistance tests ― Elements of ISO 834-8: CED 36 92

building construction: Part 8 Specific 2002
requirements for non-load bearing
vertical separating elements

22 IS/ISO 834-9:2003 Fire resistance tests ― Elements of ISO 834-9: CED 36 92

building construction: Part 9 Specific 2003
requirements for non-load bearing ceiling
elements

23 IS/ISO 3009:2003 Fire resistance tests ― Elements of ISO 3009: CED 36 92

building construction − Glazed elements 2003

24 IS/ISO 6182-7:2004 Fire protection − automatic sprinkler ISO 6182-7: CED 22 21

systems: Part 7 Requirements and test 2004
method for early suppression fast
response (ESFR) sprinkler

25 IS/ISO 7240-2:2003 Fire detection and alarm systems: ISO 7240-2: CED 22 21
Part 2 Control and indicating equipment 2003

26 IS/ISO 7240-3:2010 Fire detection and alarm systems: ISO 7240-3: CED 22 21
Part 3 Audible alarm devices 2010

27 IS/ISO 7240-4:2003 Fire detection and alarm systems: ISO 7240-4: CED 22 21
Part 4 Power supply equipment 2003

28 IS/ISO 7240-5:2012 Fire detection and alarm systems: ISO 7240-5: CED 22 21
Part 5 Point-type heat detectors 2012
(first revision)

152
Sl. IS Number Title ISO/IEC Sectional ISO/TC
No. Number Committee Number
of CED

29 IS/ISO 7240-6:2011 Fire detection and alarm systems: ISO 7240-6: CED 22 21
Part 6 Carbon monoxide fire detector 2011
using electro-chemical cells

30 IS/ ISO 7240-7:2011 Fire detection and alarm systems: ISO 7240-7: CED 22 21
Part 7 Point-type smoke detectors using 2011
scattered light, transmitted light or
ionization

31 IS/ISO 7240-8:2014 Fire detection and alarm systems: ISO 7240-8: CED 22 21
Part 8 Point-type fire detectors using a 2014
carbon monoxide sensor in combination
with a heat sensor

32 IS/ISO 7240-10: 2012 Fire detection and alarm systems: ISO 7240-10: CED 22 21
Part 10 Point-type flame detectors 2012

33 IS/ ISO 7240-11:2011 Fire detection and alarm systems: ISO 7240-11: CED 22 21
Part 11 Manual call points 2011

34 IS/ISO 7240-12:2014 Fire detection and alarm systems: ISO 7240-12: CED 22 21
Part 12 Line type smoke detectors using 2014
a transmitted optical beam

35 IS/ISO 7240-13: 2005 Fire detection and alarm systems: ISO 7240-13: CED 22 21
Part 13 Compatibility assessment of 2005
system components

36 IS/ISO 7240-15:2004 Fire detection and alarm systems: ISO 7240-15: CED 22 21
Part 15 Point-type fire detectors using 2004
scattered light, transmitted light or
ionization sensor in combination with a
heat sensor

37 IS/ISO 7240-16:2007 Fire detection and alarm systems: ISO 7240-16: CED 22 21
Part 16 Sound system control and 2007
indicating equipment

38 IS/ISO 7240-17:2009 Fire detection and alarm systems: ISO 7240-17: CED 22 21
Part 17 Short-circuit isolators 2009

39 IS/ISO 7240-18: 2017 Fire detection and alarm systems: ISO 7240-18: CED 22 21
Part 18 Input/Output devices 2017

40 IS/ISO 7240-20:2010 Fire detection and alarm systems: ISO 7240-20: CED 22 21
Part 20 Aspirating smoke detectors 2010

41 IS/ISO 7240-21: 2005 Fire detection and alarm systems: ISO 7240-21: CED 22 21
Part 21 Routing equipment 2005

42 IS/ISO 7240-22: 2017 Fire detection and alarm systems: ISO 7240-22: CED 22 21
Part 22 Smoke – Detection equipment 2017
for ducts

43 IS/ISO 7240-23:2013 Fire detection and alarm systems: ISO 7240-23: CED 22 21
Part 23 Visual alarm devices 2013

153
Sl. IS Number Title ISO/IEC Sectional ISO/TC
No. Number Committee Number
of CED

44 IS/ISO 7240-24: 2016 Fire detection and alarm systems: ISO 7240-24: CED 22 21
Part 24 Fire alarm loudspeakers 2016

45 IS/ISO 7240-25:2010 Fire detection and alarm systems: ISO 7240-25: CED 22 21
Part 25 Components using radio 2010
transmission paths

46 IS/ISO 7240-27: 2018 Fire detection and alarm systems: ISO 7240-27: CED 22 21
Part 27 Point-type fire detectors using a 2018
smoke sensor in combination with a
carbon monoxide sensor and optionally,
one or more heat sensors

47 IS/ISO 7240-29: 2017 Fire detection and alarm systems: ISO 7240-29: CED 22 21
Part 29 Video fire detectors 2017

48 IS/ISO 19706:2011 Guidelines for assessing the fire threat to ISO 19706: CED 36 92
people 2011

49 IS/ISO 12460-1:2007 Wood based panels ― Determination of ISO 12460-1: CED 20 89

formaldehyde release: 2007
Part 1 Formaldehyde emission by the 1-
cubic-metre chamber method

50 IS/ISO 15392:2019 Sustainability in buildings and civil ISO 15392: CED 58 59

engineering works – General principles 2019

51 IS/ISO 21927-1:2008 Smoke and heat control systems – ISO 21927-1: CED 36 21
Part 1: Specification for smoke barriers 2008

Total Number of Standards = 51

154
 ANNEX III

LIST OF IS NO. COVERED UNDER BIS CERTIFICATION MARKS SCHEME UNDER ‘CED’
(IS WISE AS ON 09 APRIL 2021)

Sl. IS No. Title Committee No. of

No. Lic

1 IS 204 (Part 1):1991 Tower bolts ― Specification: Part 1 Ferrous metals CED 15 7

2 IS 204 (Part 2):1992 Tower bolts ― Specification: Part 2 Non-ferrous metals CED 15 10

3 IS 205:1992 Non-ferrous metal butt hinges ― Specification CED 15 7

4 IS 208:1996 Door handles ― Specification CED 15 9

5 IS 269:2015 Ordinary Portland cement ― Specification (sixth revision) CED 02 431

6 IS 281:2009 Mild steel sliding door bolts for use with padlocks ― CED 15 6
Specification

7 IS 303:1989 Plywood for general purposes ― Specification CED 20 938

8 IS 362:1991 Parliament hinges ― Specification CED 15 3

9 IS 383:2016 Coarse and fine aggregates for concrete ― Specification CED 02 2

(third revision)

10 IS 432 (Part 1):1982 Mild steel and medium tensile steel bars and hard-drawn steel CED 54 19
wire for concrete reinforcement: Part 1 Mild steel and medium
tensile steel bars

11 IS 432 (Part 2):1982 Mild steel and medium tensile steel bars and hard-drawn steel CED 54 17
wire for concrete reinforcement: Part 2 Hard-drawn steel wire

12 IS 455:2015 Portland slag cement ― Specification (fifth revision) CED 02 163

13 IS 458:2003 Precast concrete pipes (with and without reinforcement) ― CED 53 685
Specification

14 IS 459:1992 Corrugated and semi-corrugated asbestos cement sheets ― CED 53 50

Specification

15 IS 650:1991 Specification for standard sand for testing of cement CED 02 1

(second revision)

16 IS 651:2007 Glazed stoneware pipe and fittings ― Specification CED 03 35

17 IS 710:2010 Marine plywood ― Specification CED 20 355

18 IS 712:1984 Specification for building limes CED 04 3

19 IS 774:2004 Flushing cistern for water closets and urinals (other than CED 03 1
plastic cisterns) ― Specification

20 IS 778:1984 Copper alloy gate, globe and check valves for waterworks CED 03 67
purposes

21 IS 779:1994 Water meters (Domestic Type) CED 03 24

155
Sl. IS No. Title Committee No. of
No. Lic

22 IS 781:1984 Cast copper alloy screw down bib taps and stop valves for CED 03 15
water services

23 IS 784:2019 Prestressed concrete pipes (including fittings) ― Specification CED 53 22

24 IS 848:2006 Specification for synthetic resin adhesives for plywood CED 20 7

(phenolic and aminoplastic)

25 IS 884:1985 Specification for first-aid hose-reel for fire fighting CED 22 31

26 IS 903:1993 Specification for fire hose delivery couplings, branch pipe, CED 22 59
nozzles and nozzle spanner ― Specification

27 IS 928:1984 Specification for fire bells CED 22 1

28 IS 1038:1983 Specification for steel doors, windows and ventilators CED 11 16

29 IS 1237:2012 Cement concrete flooring tiles ― Specification CED 05 11

30 IS 1322:1993 Bitumen felts for water proofing and damp-proofing CED 41 11

31 IS 1328:1996 Veneered decorative plywood ― Specification CED 20 51

32 IS 1341:2018 Steel Butt hinges ― Specification CED 15 56

33 IS 1489 (Part 1): Portland pozzolana cement ― Specification: Part 1 Fly Ash CED 02 459
2015 based (fourth revision)

34 IS 1489 (Part 2): Portland pozzolana cement ― Specification: Part 2 Calcined CED 02 17
2015 clay based (fourth revision)

35 IS 1566:1982 Hard-drawn Steel Wire Fabric For Concrete Reinforcement CED 54 1

36 IS 1580:1991 Bituminous compound for water-proofing and Caulking CED 41 2

Purposes

37 IS 1592:2003 Asbestos cement pressure pipes and joints ― Specification CED 53 15

38 IS 1626 (Part 2): Asbestos cement building pipes and pipe fittings, gutters and CED 53 1
1994 gutter fittings and roofing fittings: Part 2 Gutter and gutter
fittings

39 IS 1626 (Part 3): Asbestos cement building types and pipe fittings, gutters and CED 53 7
1994 gutter fittings and roofing fittings: Part 3 Roofing fittings

40 IS 1658:2006 Fibre hardboards ― Specification CED 20 1

41 IS 1659:2004 Block boards ― Specification CED 20 509

42 IS 1703:2000 Water fittings – Copper alloy float valves (horizontal plunger CED 03 4
Type) ― Specification

43 IS 1726:1991 Cast iron manhole covers and frames CED 03 7

44 IS 1785 (Part 1): Plain Hard-drawn steel wire for prestressed concrete: CED 54 6
1983 Part 1 Cold drawn stress-relieved wire

156
Sl. IS No. Title Committee No. of
No. Lic

45 IS 1785 (Part 2): Plain Hard-drawn steel wire for prestressed concrete: CED 54 9
1983 Part 2 As drawn wire

46 IS 1786:2008 High strength deformed steel bars and wires for concrete CED 54 538
reinforcement ― Specification

47 IS 1834:1984 Hot applied sealing compounds for joints in concrete ― CED 13 2

Specification

48 IS 1838 (Part 1): Preformed fillers for expansion joint in concrete pavement and CED 13 3
1983 structures (non extruding and resilient type): Part 1 Bitumen
impregnated fibre ― Specification

49 IS 1838 (Part 3): Preformed fillers for expansion joints in concrete pavements CED 13 3
2011 and structures (non-extruding and resilient type):
Part 3 Polymer based

50 IS 2095 (Part 1): Gypsum plaster boards: Part 1 Plain gypsum plaster boards CED 04 5
2011

51 IS 2096:1992 Asbestos cement flat sheets ― Specification CED 53 1

52 IS 2097:2012 Foam making branch pipe and foam inductor― Specification CED 22 2

53 IS 2098:1997 Asbestos cement building boards ― Specification CED 53 5

54 IS 2185 (Part 1): Concrete masonry units: Part 1 Hollow and solid concrete CED 53 3
2005 blocks

55 IS 2185 (Part 3): Concrete masonry units: Part 3 Autoclaved cellular aerated CED 53 86
1984 concrete blocks

56 IS 2202 (Part 1): Wooden flush door shutters (solid core type): CED 11 406
1999 Part 1 Plywood face panels

57 IS 2373:1981 Water meters (bulk type) CED 03 5

58 IS 2386 (Part 1): Methods of test for aggregates for concrete: Part 3 Particle CED 02 1
1963 size and shape

59 IS 2386 (Part 3): Methods of test for aggregates for concrete: Part 3 Specific CED 02 2
1963 gravity, density, voids, absorption and bulking

60 IS 2546:1974 Specification for galvanized mild steel fire bucket CED 22 2

61 IS 2547 (Part 1): Gypsum building plaster: Part 1 Excluding premixed CED 04 32
1976 lightweight plaster

62 IS 2548 (Part 2): Plastic seats and covers for water-closets: Part 2 Thermo CED 03 5
1996 plastic seats and covers

63 IS 2556 (Part 2): Vitreous sanitary appliances (vitreous China): Part 2 Specific CED 03 17
2004 requirements of washdown water closets

64 IS 2556 (Part 3): Vitreous sanitary appliances (vitreous China): Part 3 Specific CED 03 22
2004 requirements of squatting pans

157
Sl. IS No. Title Committee No. of
No. Lic

65 IS 2556 (Part 4): Vitreous sanitary appliances (vitreous China): Part 4 Specific CED 03 16
2004 requirements of wash basins

66 IS 2556 (Part 5): Vitreous sanitary appliances (vitreous China): CED 03 3

1994 Part 5 Specific requirements of laboratory sinks

67 IS 2556 (Part 6): Vitreous sanitary appliances (vitreous China): CED 03 12

1995 Part 6 Specific requirements of urinals and partition plates

68 IS 2556 (Part 7): Vitreous sanitary appliances (vitreous China): CED 03 4

1995 Part 7 Specific requirements of accessories for sanitary
appliances

69 IS 2556 (Part 15): Vitreous sanitary appliances (vitreous China): CED 03 4

2004 Part 15 Specific requirements of universal water closets

70 IS 2556 (Part 16): Vitreous sanitary appliances (vitreous China) ― Specification: CED 03 1
2002 Part 16 Specific requirements of wash down wall mounted
water closets

71 IS 2645:2003 Integral waterproofing compounds for cement mortar and CED 02 35

concrete ― Specification

72 IS 2681:1993 Non-ferrous metal sliding door bolts (aldrops) for with CED 15 7
padlocks ― Specification

73 IS 2692:1989 Ferrules for water services CED 03 14

74 IS 2713 (Part 1 to 3): Specification for tubular steel poles for overhead power lines CED 07 42
1980 (second revision)
Part 1 General requirements
Part 2 Special requirements for poles made from steel of
tensile strength 410 MPa
Part 3 Special requirements for poles made from steel of
tensile strength 540 MPa

75 IS 2745:1983 Specification for non-metal helmet for firemen and civil CED 22 1
defence personnel (second revision)

76 IS 2871:2012 Branch pipe, universal for fire fighting purpose ― CED 22 3

Specification

77 IS 2925:1984 Specification for industrial safety helmets CED 22 57

78 IS 3087:2005 Particle boards of wood and other lingnocellulosic materials CED 20 15

(medium density) for general purposes ― Specification

79 IS 3312:1984 Steel shelving cabinets (adjustable type) ― Specification CED 35 2

80 IS 3443:1980 Crane rail sections ― Specification CED 07 2

81 IS 3462:1986 Unbacked flexible pvc flooring CED 05 3

82 IS 3466:1988 Specification for masonry cement CED 02 13

83 IS 3564:1995 Hydraulically regulated door closers ― Specification CED 15 32

158
Sl. IS No. Title Committee No. of
No. Lic

84 IS 3812 (Part 1): Pulverized Fuel Ash: Part 1 For use as pozzolana in cement, CED 02 1
2013 cement mortar and concrete

85 IS 3818:1992 Continuous (piano) hinges ― Specification CED 15 3

86 IS 4038:1986 Foot valves for water works purposes CED 03 3

87 IS 4151:1993 & Protective helmet for two wheeler riders ― Specification CED 22 248
IS 4151:2015

88 IS 4308:2003 Specification for dry chemical powder for fighting b and c CED 22 31
class fires

89 IS 4351:2003 Steel door frames ― Specification CED 11 12

90 IS 4457:2007 Ceramic unglazed vitreous acid resisting tile ― Specification CED 05 1

91 IS 4835:1979 Specification polyvinyl acetate dispersion based adhesives for CED 20 1

wood

92 IS 4947:2006 Specification for gas cartridges for use in fire extinguishers CED 22 23

93 IS 4984:2016 Polyethylene pipes for water supply ― Specification CED 50 704

(fifth revision)

94 IS 4985:2000 Unplasticized PVC pipes for potable water supplies ― CED 50 840
Specification

95 IS 4989:2018 Foam concentrate for producing mechanical foam for fire CED 22 21
fighting ― Specification

96 IS 4990:2011 Plywood for concrete shuttering work ― Specification CED 20 141

97 IS 4992:1975 Specification for door handles for mortice lock (vertical type) CED 15 1

98 IS 4996:1984 Specification for reinforced concrete fence posts CED 53 5

(first revision)

99 IS 5290:1993 Specification for landing valves CED 22 59

100 IS 5312 (Part 1): Swing check type reflux (non-return] valves for water works CED 03 54
2004 purposes: Part 1 Single-door pattern

101 IS 5509:2000 Fire retardant plywood ― Specification CED 20 37

102 IS 5513:1996 Specification for vicat apparatus CED 02 1

103 IS 5514:1996 Specification apparatus used in `le-chatelier' test CED 02 1

104 IS 5516:1996 Specification variable flow type air-permeability apparatus CED 02 1

(blaine type)

105 IS 5820:1970 Precast concrete cable covers CED 53 9

106 IS 6003:2010 Indented wire for-prestressed concrete ― Specification CED 54 40

107 IS 6006:2014 Uncoated stress relieved strand for prestressed concrete ― CED 54 36
Specification

159
Sl. IS No. Title Committee No. of
No. Lic

108 IS 6073:2006 Autoclaved reinforced cellular concrete floor and roof slabs ― CED 51 2
Specification

109 IS 6315:1992 Floor springs (hydraulically regulated) for heavy doors ― CED 15 6
Specification

110 IS 6908:1991 Asbestos cement pipes and fittings for sewerage and CED 53 5
drainage

111 IS 6909:1990 Specification for supersulphated cement CED 02 1

112 IS 7231:1994 Plastic flushing cisterns for water-closets and urinals CED 03 24

113 IS 7320:1974 Specification for concrete slump test apparatus CED 02 1

114 IS 7452:1990 Specification for hot-rolled steel sections for doors, windows CED 07 9
and ventilators

115 IS 7834 (Part 1): Injection moulded PVC socket fittings with solvent cement CED 50 61
1987 joints for water supplies: Part 1 General requirements

116 IS 7834 (Part 3): Injection moulded PVC socket fittings with solvent cement CED 50 7
1987 joints for water supplies: Part 3 Specific requirements for 90
degree elbows

117 IS 8041:1990 Specification for rapid hardening Portland cement CED 02 8

118 IS 8042:2015 White Portland cement ― Specification (third revision) CED 02 11

119 IS 8229:1986 Specification for oil-well cement CED 02 5

120 IS 8360 (Part 1): Fabricated high density polyethylene (HDPE) fittings for CED 50 2
1977 potable water supplies: Part 1 General requirements

121 IS 8423:1994 Specification for controlled percolating hose for fire fighting CED 22 19

122 IS 8442:2008 Stand post type water and foam monitor for fire fighting ― CED 22 9
Specification

123 *IS 8931:1993 Copper alloy fancy single taps, combination tap assembly and CED 03 32
stop valves for water services

124 IS 9103:1999 Specification for concrete admixtures CED 02 31

125 IS 9142 (Part 2): Artificial light weight aggregates for concrete — Specification: CED 02 1
2018 Part 2 Sintered fly ash coarse aggregate (first revision)

126 IS 9271:2004 Unplasticized Polyvinyl Chloride (UPVC) single wall CED 50 4

corrugated pipes for drainage ― Specification

127 IS 9562:1980 Specification for non-metal helmet for police force CED 22 1

128 IS 9758:1981 Flush valves and fittings for water closets and urinals CED 03 1

129 IS 9762:1994 Polyethylene floats (spherical) for float valves CED 03 4

130 IS 9763:2000 Plastics bib taps, pillar taps, angle valves and stop valves for CED 03 30
hot and cold water services ― Specification

160
Sl. IS No. Title Committee No. of
No. Lic

131 *IS 9972:2002 Specification for automatic sprinkler heads for fire protection CED 22 3
service

132 IS 9973:1981 Specification for visor for scooter helmets CED 22 6

133 IS 10079:1982 Specification for cylindrical metal measures for use in tests of CED 02 1
aggregates and concrete

134 IS 10080:1982 Specification for vibration machine for standard cement CED 02 5
mortar cubes

135 IS 10086:1982 Specification for moulds for use in tests of cement and CED 02 12
concrete

136 IS 10124 (Part 1): Fabricated PVC-U fittings for potable water supplies ― CED 50 11
2009 specification: Part 1 General requirements

137 IS 10124 (Part 2): Fabricated PVC-U fittings for potable water supplies ― CED 50 47
2009 Specification: Part 2 Specific requirements for sockets

138 IS 10701:2012 Specification for structural plywood ― Specification CED 20 6

139 IS 11833:1986 Specification for dry powder fire extinguisher for metal fires CED 22 1

140 IS 12118 (Part 1): Specification for two-part polysulphide-based sealants: CED 13 1
1987 Part 1 General requirements

141 IS 12234:1988 Plastic equilibrium float valve for cold water services CED 03 3

142 IS 12330:1988 Specification for sulphate resisting Portland cement CED 02 19

143 IS 12406:2003 Medium density fibre boards for general purpose ― CED 20 10
Specification

144 IS 12592:2002 Precast concrete manhole cover and frame ― Specification CED 53 119

145 IS 12701:1996 Rotational moulded polyethylene water storage tanks CED 03 175

146 IS 12709:1994 Glass-fibre reinforced plastic (GRP) pipes joints and fittings CED 50 8
for use for potable water supply

147 IS 12817:2013 Stainless steel butt hinges ― Specification CED 15 14

148 IS 12818:2010 Unplasticized Polyvinyl Chloride (PVC-U) screen and casing CED 50 200
pipes for bore/tubewell

149 IS 12823:2015 Prelaminated particle boards from wood and other CED 20 17
lignocellulosic material ― Specification (first revision)

150 IS 12866:1989 Plastic translucent sheets made from thermosetting polyester CED 05 1
resin (glass fibre reinforced)

151 IS 12894:2002 Pulverized fuel ash-lime bricks ― Specification CED 04 6

152 IS 13000:1990 Silica-asbestos-cement flat sheets ― Specification CED 53 1

153 IS 13049:1991 Diaphragm type (plastic body) float operated valves for cold CED 03 8
water services

161
Sl. IS No. Title Committee No. of
No. Lic

154 IS 13114:1991 Forged brass gate, globe and check valves for water works CED 03 1
purposes

155 IS 13592:2013 Unplasticized Polyvinyl Chloride (PVC-U) pipes for soil and CED 50 202
waste discharge system inside and outside buildings including
ventilation and rainwater system

156 IS 13620:1993 Fusion bonded epoxy coated reinforcing bars ― Specification CED 54 9

157 IS 13801:2013 Chequered cement concrete tiles ― Specification CED 05 21

158 IS 13958:1994 Bamboo mat board for general purposes ― Specification CED 20 1

159 IS 13983:1994 Stainless steel sinks for domestic purposes CED 03 27

160 IS 14268:2017 Uncoated stress relieved low relaxation seven-wire (ply) CED 54 7
strand for prestressed concrete ― Specification
(first revision)

161 IS 14276:2016 Cement bonded particle boards ― Specification CED 20 2

(first revision)

162 IS 14333:1996 High density polyethylene pipe for sewerage ― Specification CED 50 85

163 IS 14399 (Part 1): Hot press moulded thermosetting glass fibre reinforced CED 03 2
1996 polyester resin (GRP) sectional water storage tanks:
Part 1 Specification for panels

164 IS 14402:1996 GRP pipes joints and fittings for use sewerage, industrial CED 50 6
waste and water (other than potable)

165 IS 14587:1998 Prelaminated medium density fibre board ― Specification CED 20 9

166 IS 14616:1999 Laminated veneer lumber ― Specification CED 20 1

167 IS 14735:1999 Unplasticized Polyvinyl Chloride (UPVC) injection moulded CED 50 69

fittings for soil and waste discharge system for inside and
outside buildings including ventilation and rain water system
― Specification

168 IS 14845:2000 Resilient seated cast iron air relief valves for water works CED 03 24
purposes ― Specification

169 IS 14846:2000 Sluice valve for water works purposes (50 to 1200 mm Size) CED 03 93
― Specification
170 IS 14856:2000 Glass fibre reinforced plastic (GRP) panel type door shutters CED 11 1
for internal use ― Specification

171 IS 14858:2000 Requirements for compression testing machine used for CED 02 2
testing of concrete and mortar

172 IS 14862:2000 Fibre cement flat sheets ― Specification CED 53 11

173 IS 14871:2000 Products in fibre reinforced cement - long corrugated or CED 53 4

asymmetrical section sheets and fittings for roofing and
cladding ― Specification

162
Sl. IS No. Title Committee No. of
No. Lic

174 IS 14885:2001 Polyethylene pipes for the supply of gaseous fuels ― CED 50 35
Specification

175 IS 14933:2001 High pressure fire fighting hose ― Specification CED 22 3

176 IS 14951:2001 Fire extinguisher − 135 litres capacity mechanical foam type CED 22 2
― Specification

177 IS 15155:2002 Bar/Wire wrapped steel cylinder pipes with mortar lining and CED 53 13
coating (including specials) ― Specification

178 IS 15265:2003 Flexible PVC pipes or polymer reinforced thermoplastic hoses CED 50 8
for suction and delivery lines of agricultural pumps ―
Specification

179 IS 15328:2003 Unplasticized non-pressure polyvinyl chloride (PVC -U) pipes CED 50 55
for use in underground drainage and sewerage systems ―
Specification

180 IS 15380:2003 Moulded raised high density fibre (HDF) panel doors ― CED 11 6
Specification

181 IS 15450:2004 Polyethylene/ aluminium/ polyethylene composite pressure CED 50 5

pipes for hot and cold water supplies ― Specification

182 IS 15476:2004 Bamboo mat corrugated sheets ― Specification CED 20 1

183 IS 15477:2019 Adhesives for use with ceramic, mosaic and stone tiles ― CED 05 29
Specification (first revision)

184 IS 15622:2017 Pressed ceramic tiles ― Specification (first revision) CED 05 33

185 IS 15658:2006 Precast concrete blocks for paving ― Specification CED 05 2156

186 IS 15683:2006 Portable fire extinguishers − performance and construction ― CED 22 104
Specification

187 IS 15778:2007 Chlorinated Polyvinyl Chloride (CPVC) pipes for potable hot CED 50 96
and cold water distribution supplies ― Specification

188 IS 15786:2008 Prelaminated cement bonded particle board ― Specification CED 20 1

189 IS 15801:2008 Polypropylene-random copolymer pipes for hot and cold CED 50 19
water supplies ― Specification

190 IS 15833:2009 Stainless steel tower bolts ― Specification CED 15 3

191 IS 15834:2008 Stainless steel sliding door bolts (aldrops) for use with CED 15 2
padlocks ― Specification

192 IS 16018:2012 Wheeled fire extinguishers – performance and construction ― CED 22 33

Specification

193 IS 16088:2012 Chlorinated Polyvinyl Chloride (CPVC) pipes for automatic CED 22 3
sprinkler fire extinguishing system ― Specification

194 IS 16098 (Part 1): Structured-wall plastics piping systems for non-pressure CED 50 8
2013 drainage and sewerage: Part 1 Pipes and fittings with smooth
external surface, type A

163
Sl. IS No. Title Committee No. of
No. Lic

195 IS 16098 (Part 2): Structured-wall plastics piping systems for non-pressure CED 50 37
2013 drainage and sewerage: Part 2 Pipes and fittings with non-
smooth external surface, type B

196 IS 16353:2015 Portland cement clinker ― Specification CED 02 1

197 IS 16415:2015 Composite cement ― Specification CED 02 60

198 IS 16644:2018 Steel relieved low relaxation steel wires for prestressed CED 54 1
concrete ― Specification

199 IS 16647:2017 Oriented unplasticized polyvinyl chloride (PVC-O) pipes for CED 50 5
water supply ― Specification

200 IS 16651:2017 High strength deformed stainless steel bars and wires for CED 54 2
concrete reinforcement ― Specification

201 IS 16714:2018 Ground granulated blast furnace slag for cement mortar and CED 02 8
concrete ― Specification

202 IS 16715:2018 Ultrafine ground granulated blast furnace slag ― Specification CED 02 2

203 IS 16720:2018 Pulverized fuel ash-cement bricks ― Specification CED 53 2

204 IS 16993:2018 Microfine ordinary Portland cement ― Specification CED 02 1

12089
Total

164
 ANNEX IV

LIST OF IS UNDER ECO MARK

Sl. Sectional IS Number Title

No. Committee

1 CED 04 IS 2095 (Part 1):2011 Specification for gypsum plaster boards: Part 1 Plain gypsum plaster
boards (third revision)

2 IS 2095 (Part 2):2001 Specification for gypsum plaster boards: Part 2 Coated/ laminated
gypsum plaster boards

3 IS 2095 (Part 3):2018 Gypsum plaster boards — Specification: Part 3 Reinforced gypsum
plaster boards, tiles, cornices and mouldings (third revision)

4 IS 2849:1983 Specification for non-load bearing gypsum partition blocks (solid and
hollow types)

5 CED 11 IS 1003 (Part 1):2003 Specification for timber panelled and glazed shutters: Part 1 Door
shutters (third revision)

6 IS 1003 (Part 2):1994 Specification for timber panelled and glazed shutters: Part 2 Window
and ventilator shutters (third revision)

7 IS 2191 (Part 1):1983 Specification for wooden flush door shutters (cellular and hollow core
type): Part 1 Plywood face panels (fourth revision)

8 IS 2191 (Part 2):1983 Specification for wooden flush door shutters (cellular and hollow core
type): Part 2 Particle board and hardboard face panels
(third revision)

9 IS 2202 (Part 1):1999 Specification for wooden flush door shutters (solid core type):
Part 1 Plywood face panels (sixth revision)

10 IS 2202 (Part 2):1983 Specification for wooden flush door shutters (solid core type):
Part 2 Particle board face panels and hardboard face panels
(third revision)

11 IS 4021:1995 Specification for timber door, window and ventilator frames

(third revision)

12 IS 6198:1992 Specification for ledged, braced and battened timber door

shutters(second revision)

13 IS15380:2003 Specification for moulded raised high density fibre (HDF) panel
doors

14 CED 20 IS 303:1989 Specification for plywood for general purposes (third revision)

15 IS 710:2010 Specification for marine plywood (second revision)

16 IS 1328:1996 Specification for veneered decorative plywood (third revision)

17 IS 1658:2006 Specification for fibre hardboards (third revision)

18 IS 1659:2004 Specification for block boards (fourth revision)

19 IS 3087:2005 Specification for particle boards of wood and other lignocellulosic

materials (medium density) for general purposes (second revision)

165
Sl. Sectional IS Number Title
No. Committee

20 IS 3097:2006 Specification for veneered particle boards (second revision)

21 IS 3129:1985 Specification for low density particle boards (first revision)

22 IS 3308:1981 Specification for wood wool building slabs (first revision)

23 IS 4990:2011 Specification for plywood for concrete shuttering work (third revision)

24 IS 5509:2000 Specification for fire retardant plywood (second revision)

25 IS 12406:2003 Specification for medium density fibre boards for general purpose
(first revision)

26 IS 12823:2015 Wood products pre-laminated particle boards ― Specification

(first revision)

27 IS 13958:1994 Specification for bamboo mat board for general purposes

28 IS 14587:1998 Specification for pre-laminated medium density fibre board

29 IS 14588:1999 Specification for bamboo mat veneer composites for general

purposes

30 IS 14616:1999 Specification for laminated veneer lumber

31 IS14842:2000 Specification for coir veneer board for general purposes

32 IS 15476:2004 Specification for bamboo mat corrugated sheets

33 IS 15491:2004 Specification for medium density, coir boards for general purposes

34 IS 15877:2010 Specification for coir faced blockboards

35 IS 15878:2010 Specification for coir hardboards for general purposes

36 IS 16171:2014 Veneer laminated lumber ― Specification

37 CED 22 IS 11833:1986 Specification for dry powder fire extinguisher for metal fires

38 CED 35 IS 1829 (Part 1):2017 Specification for library furniture and fittings: Part 1 Timber
(second revision)

39 IS 4116:1988 Specification for wooden shelving cabinets (adjustable type)

(second revision)

40 IS 4126:1986 Specification for wooden wardrobes (adjustable type and non-

adjustable type)

41 IS 4414:1990 Specification for wooden table tops (second revision)

42 IS 5823:1986 Specification for dining tables (first revision)

43 IS 5923:1986 Specification for wooden clothes lockers (first revision)

44 IS 5974:1986 Specification for divans and easy chairs (first revision)

166
Sl. Sectional IS Number Title
No. Committee

45 IS 6188:1988 Specification for wooden bedside table (first revision)

46 IS 6632:1988 Specification for wooden folding chairs

47 IS 7070:1988 Wooden shelving racks (adjustable type and non-adjustable type)

(first revision)

48 IS7259 (Part1):1988 Wooden beds: Part 1 for use with mattresses (first revision)

49 IS 11525:1986 Wooden chairs for office purposes

50 IS 11679:1986 Wooden tables for office purposes

51 IS 12680:1989 Wooden-sofa-cum-bed

52 CED 53 IS 6523:1983 Specification for pre-cast reinforced concrete door and window
frames (first revision)

167
 ANNEX V

LIST OF BILINGUAL/HINDI STANDARDS

A) PUBLISHED STANDARDS IN HINDI

SI IS Number Year Title

No.

1 IS 10 (Part 3) 1974 Specification for plywood tea-chests: Part 3 Battens

2 IS 432 (Part 1) 1982 Specification for mild steel and medium tensile steel bars and hard-drawn
steel wire for concrete reinforcement: Part 1 Mild steel and medium tensile
steel bars

3 IS 432 (Part 2) 1982 Specification for mild steel and medium tensile steel bars and hard-drawn
steel wire for concrete reinforcement: Part 2 Hard-drawn steel wire

4 IS 3583 1988 Specification for burnt clay paving bricks

5 IS 3763 1983 Specification for metal folding chairs

6 IS 11679 1986 Specification for wooden tables for office use

7 IS 13827 1993 Improving earthquake resistance of earthen buildings ― Guidelines

8 IS 13828 1993 Improving earthquake resistance of low strength masonary buildings ―

Guidelines

B) BILINGUAL STANDARDS

SI IS Number Year Title

No.

1 IS 2925 1984 Specification for Industrial Safety Helmets

2 IS 3466 1988 Specification for masonry cement

3 IS 3952 1988 Specification for burnt clay hollow bricks for walls and partitions

4 IS 6452 1989 Specification for high alumina cement for structural use

5 IS 6909 1990 Specification for supersulphated cement

6 IS 7556 1988 Specification for burnt clay jallies

7 IS 8041 1990 Specification for rapid hardening Portland cement

8 IS 8043 1991 Specification for hydrophobic Portland cement

168
 ANNEX VI

MEMBERSHIP STATUS IN ISO COMMITTEES & SUB-COMMITTEES

SI Title of TC and SC Type of

No. Membership

1 TC 17 – Steel

SC 3 – Steels for structure purposes P

SC 16 – Steels for the reinforcement and prestressing of concrete O

2 TC 21 – Equipment for fire protection and fire fighting O

SC 2 – Manually transportable fire extinguishers O

SC 3 – Fire detection and alarm system O

SC 5 – Fixed fire fighting systems using water O

SC 6 – Foam and powder media and fire fighting systems using foam and O
powder

SC 8 − Gaseous media and firefighting systems using gas O

SC 11 − Smoke and heat control systems and components O

3 TC 24 – Particle characterization including sieving O

SC 4 – Particle characterization O

SC 8 – Test sieves, sieving and industrial screens P

4 TC 43 – Acoustics

SC 2 – Building acoustics O

5 TC 59 – Buildings and civil engineering works O

SC 2 – Terminology and harmonization of languages O

SC 8 – Sealants O

SC 13 – Organization of information about construction works O

SC 16 – Accessibility and usability of the built environment O

SC 17 − Sustainability in buildings and civil engineering works O

6 TC 67 – Materials, equipment and offshore structures for petroleum,

petrochemical and natural gas industries

SC 7 – Off-shore structures O

7 TC 71 – Concrete, reinforced concrete and prestressed concrete P

SC 1 – Test methods for concrete P

169
SI Title of TC and SC Type of
No. Membership

SC 3 – Concrete production and execution of concrete structures P

SC 4 – Performance requirements for structural concrete P

SC 5 – Simplified design standard for concrete structures P

SC 6 – Non traditional reinforcing materials for concrete structures P

SC 7 – Maintenance and repair of concrete structures P

SC 8 – Environment Management for concrete and concrete structures P

8 TC 74 – Cement and lime P

9 TC 77 – Products in fibre reinforced cement O

10 TC 89 – Wood based panels O

SC 1 – Fibre boards O

SC 2 – Particle boards O

SC 3 – Plywood O

11 TC 92 – Fire safety O

SC 1 – Fire initiation and growth O

SC 2 – Fire containment O

SC 3 – Fire threat to people and environment O

12 TC 98 – Bases for design of structures P

SC 1 – Terminology and symbols P

SC 2 – Reliability of structures P

SC 3 – Loads, forces and other actions P

13 TC 136 – Furniture O

14 TC 138 – Plastic pipes, fittings and valves for the transport of fluids O

SC 1 – Plastic pipes and fittings for soil, waste and drainage (including land O
drainage)

SC 2 – Plastic pipes and fittings for water supplies O

SC 3 – Plastic pipes and fittings for industrial application O

SC 4 – Plastic pipes and fittings for the supply of gaseous fuels O

SC 5 – General properties of pipes, fittings and valves of plastic materials and O

their accessories, test methods and basic specification

SC 6 – Reinforced plastic pipes and fittings for all applications O

SC 7 – Valves and auxiliary equipment of plastic materials O

170
SI Title of TC and SC Type of
No. Membership

15 TC 162 – Doors and windows O

16 TC 165 – Timber structures P

17 TC 167 – Steel and aluminium structures O

SC 1 – Steel: material and (STANDBY) O

SC 3 – Aluminium structures (STANDBY) O

18 TC 182 – Geotechnics O

19 TC 189 – Ceramic tile P

20 TC 218 Timber O

21 TC 268 – Sustainable cities and communities P

SC 1 – Smart community infrastructures P

22 ISO/TC 287 – Sustainable process for wood and wood-based products P

23 ISO/TC 296 – Bamboo and rattan P

24 ISO/PC 316 – Water efficient products – Banding P

25 ISO/PC 318 – Community scale resource oriented sanitation treatment systems O

26 ISO/TC 327 – Natural stones P

27 ISO/TC 328 – Engineered stones P

P – PARTICIPATING MEMBER
O – OBSERVER MEMBER

171
 ANNEX VII

LIST OF MANDATORY STANDARDS

SI IS Number Year Title

No.

1 IS 269 2015 Ordinary Portland cement ― Specification (sixth revision)

2 IS 432 (Part 1) 1982 Specification for mild steel and medium tensile steel bars and hard-
drawn steel wire for concrete reinforcement: Part 1 Mild steel and
medium tensile steel bars (third revision)

3 IS 432 (Part 2) 1982 Specification for mild steel and medium tensile steel bars and hard-
drawn steel wire for concrete reinforcement: Part 2 Hard drawn steel
wire (third revision)

4 IS 455 2015 Portland slag cement ― Specification (fifth revision)

5 IS 1489 (Part 1) 2015 Portland pozzolana cement ― Specification: Part 1 Flyash based
(fourth revision)

6 IS 1489 (Part 2) 2015 Portland pozzolana cement ― Specification: Part 2 Calcined clay
based (fourth revision)

7 IS 1566 1982 Specification for hard-drawn steel wire fabric for concrete
reinforcement (second revision)

8 IS 1785 (Part 1) 1983 Specification for plain hard-drawn steel wire for prestressed concrete:
Part 1 Cold drawn stress-relieved wire (second revision)

9 IS 1785 (Part 2) 1983 Specification for plain hard-drawn steel wire for prestressed concrete:
Part 2 As drawn wire (second revision)

10 IS 1786 2008 High strength deformed steel bars and wires for concrete
reinforcement ― Specification (fourth revision)

11 IS 2090 1983 Specification for high tensile steel bars used in prestressed concrete
(first revision)

12 IS 3466 1988 Specification for masonry cement (second revision)

13 IS 6003 2010 Specification for indented wire for prestressed concrete

(second revision)

14 IS 6006 2014 Uncoated stress relieved strand for prestressed concrete ―

Specification (second revision)

15 IS 6452 1989 Specification for high alumina cement for structural use (first revision)

16 IS 6909 1990 Specification for supersulphated cement (first revision)

17 IS 8041 1990 Specification for rapid hardening Portland cement (second revision)

18 IS 8042 2015 White Portland cement ― Specification (third revision)

19 IS 8043 1991 Specification for hydrophobic Portland cement

20 IS 8229 1986 Specification for Oil-well Cement

21 IS 12330 1988 Specification for sulphate resisting Portland cement

172
SI IS Number Year Title
No.

22 IS 12600 1989 Specification for low heat Portland cement

23 IS 13620 1993 Fusion boned epoxy coated reinforcing bars ― Specification

24 IS 14268 2017 Uncoated stress relieved low relaxation seven wire(ply) strand for
prestressed concrete ― Specification (first revision)

25 IS 16415 2015 Composite cement — Specification

26 IS 16644 2018 Stress-relieved low relaxation steel wire for prestressed concrete ―
Specification

27 IS 16993 2018 Microfine ordinary Portland cement ― Specification

173
 ANNEX VIII

LIST OF IS TRANSFERRED TO OTHER DEPARTMENTS

(SINCE 01 APRIL 2018)

SI IS Number Title
No.

1 IS 5533:1969 Recommendation for dimensions for spaces for human activities

2 IS 4838:1990 Anthropometric dimensions for school children age group 5-17 years
(second revision)

3 IS 1852:1985 Specification for Rolling and cutting tolerances for hot-rolled steel products
(fourth revision)

174
 ANNEX IX
LIST OF SPECIAL PUBLICATIONS

SI IS Number Year Title

No.

1 SP 6 (Part 4) 1969 ISI Handbook for Structural Engineers 4. Use of High Strength Friction Grip Bolts

2 SP 6 (Part 5) 1980 Handbook for Structural Engineers - Cold-Formed, Light Gauge Steel Structures

3 SP 6 (Part 6) 1972 Handbook for Structural Engineers - Application of Plastic Theory in Design of
Steel Structures

4 SP 7 2016 National Building Code of India 2016

5 SP 7 (Group 1) 2016 National Building Code of India 2016: Group 1

6 SP 7 (Group 2) 2016 National Building Code of India 2016: Group 2

7 SP 7 (Group 3) 2016 National Building Code of India 2016: Group 3

8 SP 7 (Group 4) 2016 National Building Code of India 2016: Group 4

9 SP 7 (Group 5) 2016 National Building Code of India 2016: Group 5

10 SP 20 (S&T) 1991 Handbook on Masonry Design and Construction (first revision)

11 SP 21 (S&T) 2005 Summaries of Indian Standards for Building Materials

12 SP 23 1982 Handbook on Concrete Mixes

13 SP 25 (S&T) 1984 Handbook on Causes and Prevention of Cracks in Building

14 SP 27 1987 Handbook on Method of Measurement of Buildings Works

15 SP 32 1986 Handbook on Functional Requirements of Industrial Buildings (Lighting and

Ventilation)

16 SP 33 1987 Handbook on Timber Engineering

17 SP 34 1987 Handbook on Concrete Reinforcement and Detailing

18 SP 35 (S&T) 1987 Handbook on Water Supply and Drainage (with Special Emphasis on Plumbing)

19 SP 36 (Part 1) 1987 Compendium of Indian standards on Soil Engineering: Part 1 Laboratory Testing
of Soils for Civil Engineering Purposes

20 SP 36 (Part 2) 1988 Compendium of Indian Standards on Soil Engineering: Part 2 Field Testing

21 SP 41 (S&T) 1987 Handbook on Functional Requirements of Buildings (Other than Industrial

Buildings)

22 SP 43 (S&T) 1987 Handbook on Structures with Reinforced Concrete Portal Frames (Without
Cranes)

23 SP 57 QAWSM) 1993 Handbook on Pipes and Fittings for Drinking Water Supply

24 SP 62 1997 Handbook on Building Construction Practices (Excluding Electrical Work)

25 SP 64 (S&T) 2001 Explanatory Handbook on Indian Standard Code of Practice for Design Loads
(Other than Earthquake) for Buildings and Structures: Part 2 Wind loads
[IS 875 (Part 3):1987]

175
SI IS Number Year Title
No.

26 SP 70 2001 Handbook on Construction Safety Practices

27 SP 1650 1973 Standard Colours for Building and Decorative Finishes (with Supplement)

*************

176