Experiment No. 02: RC Coupled Single Stage BJT Common Collector Amplifier
Experiment No. 02: RC Coupled Single Stage BJT Common Collector Amplifier
02
RC coupled single stage BJT Common Collector Amplifier
OBJECTIVE
Construct an RC coupled single stage BJT Common CollectorAmplifier and analyze
its performance in terms of gain, input and output impedance.
EQUIPMENT
Instruments Components
• Transistors: 2N3904
• Digital Multimeter (DMM) • Resistors: 10k, 6.8k, 10k
• Oscilloscope with probes. • Capacitors: 0.1F, 10µF
• Function generator. • Potentiometer 1k, 5k, 100k
• Variable resistors
THEORY
The common collector amplifier is one of the three basic BJT amplifier topologies. In this
circuit, the base of the transistor serves as an input; emitter as the output and the collector is
grounded that is, common for both emitter and base. It is also called as an emitter follower. This
configuration acts as a buffer. This circuit provides offer low output impedance while taking
high input impedance. The load resistor in the common collector amplifier being placed in series
with the emitter circuit receives both the base current and collector currents. Since the emitter of
a transistor is the sum of the base and collector currents, since the base and collector currents
always add together to form the emitter current, it would be reasonable to assume that this
amplifier will have a very large current gain. The common collector amplifier has quite a large
current gain, larger than any other transistor amplifier configuration.
In common collector amplifier as the collector resistance is made to zero, the collector is
at AC ground that is the reason for which the circuit is also called as grounded-collector
amplifier or this configuration has voltage gain close to unity and hence a change in base voltage
appears as an equal change across the load at the emitter, hence the name emitter follower is
given to this circuit. In other words emitter follows the input signal.
This circuit performs the function of impedance transformation over a wide range of
frequencies with voltage gain close to unity. In addition to that, the emitter follower increases the
output level of the signal. Since the output voltage across the emitter load can never exceed the
input voltage to base as emitter-base junction would become back biased. Common collector
state has a low output resistance, the circuit suitable to serve as buffer or isolating amplifier or
couple to a load with large current demands. A single stage common Collector RC coupled
amplifier is a simple and elementary amplifier circuit. The capacitor CB at the input acts as a
filter which is used to block the DC voltage and allow only AC voltage to the transistor. If any
external DC voltage reaches the base of the transistor, it will alter the biasing conditions and
affects the performance of the amplifier.
CIRCUITDIAGRAM
PROCEDURE
1. Using a Multimeter, measure the value of all Resistors and Capacitors being used in the
circuit. Also verify working of your BJT by testing it with DMM.
2. To find Q point:
Connect the circuit without Vinand capacitors. Set Vcc= 15V. Measure dc voltages at the base
VB, collector Vc and VE with respect to ground. Determine VCE and IC. The Q point is Q
(VCE,IC)
3. Now connect the circuit as per the circuit diagram.
4. Mid-band Gain and Mid-band frequency:
a. Connect the signal generator and apply a sine wave of peak-to peak amplitude 5V at
1kHz.
b. Connect input (Vin) and output (Vo) of the circuit to the two channels of Oscilloscope and
observe the waveforms.
5. Input impedance:
POT
Vo
Vin
a. Connect a Potentiometer (POT) between input voltage source and the base of the
transistor (series connection).
Set Potentiometer (POT) to zero.
Keep Input sine wave amplitude to the one evaluated in step 4(e).
Keep Input sine wave frequency to any mid band frequencyevaluated in step
4(f).
b. Connect AC voltmeter (Range: 0-10V) across the biasing resistor R2.
c. Vary the value of Potentiometer such that the AC voltmeter reads a voltage half of the
inputsignal value.
d. Measure the value of the potentiometer with a multimeter. This is the Input Impedance at
mid-band frequency.
6. Output impedance:
Vin
Pot Vo
a. Connect a Potentiometer between input voltage source and the base of the transistor
(series connection)
--------------------------------------------------------
LAB REPORT EVALUATION
No. Criteria Maximum Score Awarded Score Lab Engineer Signature with Date
1 Completeness 2.5
2 Correctness 2.5
Total 5
--------------------------------------------------------