0% found this document useful (0 votes)
213 views

Innotech Viewport Operating

The document provides instructions for accessing and using the Viewport controller interface. It describes how to [1] wake up the sleeping controller by pressing the LOGON button, [2] access the Genesis network by entering an access key, and [3] view parameters in watch pages accessed through function keys. Editing parameters involves using navigation keys to select editable values and increase/decrease buttons to change them before pressing enter. Time schedules can be changed by navigating to a schedule, editing the on/off times, and pressing enter. The document stresses ensuring parameters are correctly set before leaving the installation.

Uploaded by

Pacifico Franco
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
213 views

Innotech Viewport Operating

The document provides instructions for accessing and using the Viewport controller interface. It describes how to [1] wake up the sleeping controller by pressing the LOGON button, [2] access the Genesis network by entering an access key, and [3] view parameters in watch pages accessed through function keys. Editing parameters involves using navigation keys to select editable values and increase/decrease buttons to change them before pressing enter. Time schedules can be changed by navigating to a schedule, editing the on/off times, and pressing enter. The document stresses ensuring parameters are correctly set before leaving the installation.

Uploaded by

Pacifico Franco
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INNOTECH VIEWPORT

VIEWPORT

When first approaching the Viewport, the system is in the sleeping mode. The Viewport explains how
to view any controllers on the Genesis network on the display. However the following is an overview
of accessing the controller.

1. Press the LOGON button to Wakeup the controller.


2. The controller will then find any Genesis Controllers connected to the network. In this case there is
only one.
3. To access the Genesis network, enter the access key. (PRESS F1 four times)
4. System identification, variable inputs and current status are continuously scrolled on the Viewport
front panel for 60 seconds. If no action is taken for these 60 seconds, the Viewport will LOGOFF
automatically.
5. Functional parameters, both “read only” and “editable” are displayed in watch pages accessed
by the 8 function keys (F1-F8). User and system codes combined with panel navigation
(up/down/left/right) and control keys (increase/decrease/enter/escape) provide for easy local
control.

VIEWING PARAMETERS

1. A valid user code must be entered with the use of the 8 function keys, (i.e. F1=1)
2. Watch pages accessible by that code, are then displayed as access keys 1-8
3. Entering an access key allows scrolling of parameters assigned to that watch page.
4. A solid block indicates a “read only” parameter
5. A hollow block indicates and “editable” parameter

EDITING A SETPOINT

1. Enter a valid access code


2. Select correct watch page via access key
3. Move cursor to editable parameter (hollow block)
4. Use right arrow to shift cursor to under editable value.
5. Increase/decrease to assign new value
6. Press enter to set parameter value
7. Navigate to next parameter or escape to return to front page.

FOR SERVICE CONTACT:

Innotech Control Systems Australia


6 McKechnie Drive
Eight Mile Plains Qld 4109

Ph: 0738411388
Fx: 073841 1644

Y:\Sales\Templates\Genesis\Viewport Operating Instructions.doc


CHANGING TIME SCHEDULE

1. Enter system code (Press F8 four times)


2. Press F3
3. Locate required schedule using navigation keys
4. Press enter (screen now displays the schedule name, 1st on/off time, function edit)
5. Scrolls to the period to be edited and press enter.
6. Editing is indicated, edit “on” time
7. Shift cursor to “off” time and edit
8. Press enter (edit other time schedules in this manner)

ENSURE THAT ALL PARAMETERS ARE SET CORRECTLY, BEFORE LEAVING THE
INSTALLATION. YOU ARE RESPONSIBLE.

FOR SERVICE CONTACT:

Innotech Control Systems Australia


6 McKechnie Drive
Eight Mile Plains Qld 4109

Ph: 0738411388
Fx: 073841 1644

Y:\Sales\Templates\Genesis\Viewport Operating Instructions.doc

You might also like