Scribd
Upload
10K views

C0033-02-Right Front Tone Wheel - General Signal Failure: When Monitored and Set Conditions

This document provides diagnostic steps for a C0033-02 DTC related to the right front tone wheel in the ABS module. The diagnostic procedure involves checking for an active DTC, monitoring wheel speed sensor signals, inspecting tire pressure and tire matching, and inspecting the right front tone wheel for damage or debris. If issues are found, repairs are made and verification tests are run to check if the trouble code is still present.

Uploaded by

Gti Motors
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
10K views

C0033-02-Right Front Tone Wheel - General Signal Failure: When Monitored and Set Conditions

This document provides diagnostic steps for a C0033-02 DTC related to the right front tone wheel in the ABS module. The diagnostic procedure involves checking for an active DTC, monitoring wheel speed sensor signals, inspecting tire pressure and tire matching, and inspecting the right front tone wheel for damage or debris. If issues are found, repairs are made and verification tests are run to check if the trouble code is still present.

Uploaded by

Gti Motors
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

22/2/2021 techCONNECT Content

28 - DTC-Based Diagnostics/MODULE, Antilock Brake (ABS)/Diagnosis and Testing

C0033-02-RIGHT FRONT TONE WHEEL - GENERAL SIGNAL FAILURE

When Monitored and Set Conditions


When Monitored: This diagnostic runs continuously when the following conditions are met:

Ignition on.
Vehicle speed.

Set Conditions:

Anti-lock Brake System (ABS) Module detects periodic drops of a Wheel Speed Sensor (WSS) signal.

Default Actions:

ABS is disabled.

Possible Causes

RIGHT FRONT TONE WHEEL/BEARING DAMAGE

IMPROPER RIGHT FRONT TIRE PRESSURE/MISMATCHED TIRES

DIRTY TONE WHEEL/SENSOR

Always perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE before proceeding. (Refer to 28 -


DTC-Based Diagnostics/Standard Procedure) .

NOTE: If DTC C0034-1D is present it must be repaired before continuing with this procedure.

1. CHECK FOR AN ACTIVE DTC

NOTE: This DTC must be active for the results of this test to be valid.
1. Perform any Service Bulletins that may apply.
2. Turn the ignition on.
3. With the scan tool, read DTCs.
4. With the scan tool, read and record Environmental Data to help identify the conditions in which the DTC was set.
5. With the scan tool, erase DTCs.
6. Cycle the ignition switch off then on.

CAUTION:
Ensure brake capability is available before road testing.

7. Test drive the vehicle in a straight line to 25 mph (40 km/h).

https://dealerconnect.chrysler.com/portal/Controller/Portal 1/3
22/2/2021 techCONNECT Content

NOTE: Vehicle must be driven above 25 mph (40 km/h) for set conditions to be meet.
8. With the scan tool, read DTCs.

Is the DTC active?

Yes

Go To 3

No

Go To 2

2. CHECK WHEEL SPEED SENSOR SIGNALS

1. Turn the ignition on.


2. With the scan tool, monitor and graph ALL the WSS speeds and compare graph while an assistant drives the
vehicle.

NOTE: If graph shows periodic dropouts pay close attention to the tone wheel.
3. Slowly accelerate as straight as possible from a stop to 25 mph (40 km/h).

Is the Right Front WSS speed showing 0 mph (0 km/h) or not matching other wheels or showing erratic
behavior?

Yes

Go To 3

No

Perform the ABS-INTERMITTENT CONDITION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE,


Antilock Brake (ABS) - Standard Procedure).

3. CHECK FOR IMPROPER RIGHT FRONT TIRE PRESSURE/MISMATCHED TIRES

1. Turn the ignition off.


2. Check and adjust the Right Front Tire pressure.
3. Check and adjust all other tire pressures.
4. Inspect for mismatched tires on vehicle.

Is the Right Front Tire improperly inflated or mismatched tires on vehicle?

Yes

Repair as necessary.
Perform the ABS VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Antilock Brake (ABS)
- Standard Procedure).

No

https://dealerconnect.chrysler.com/portal/Controller/Portal 2/3
22/2/2021 techCONNECT Content

Go To 4

4. CHECK THE RIGHT FRONT TONE WHEEL/BEARING FOR DAMAGE

NOTE: Check the tone wheel teeth for missing teeth, cracks, or looseness. Teeth should be perfectly square,
not bent, or nicked.
1. Check the Right Front Tone Wheel for damage.
2. Inspect the Right Front Tone Wheel for debris.

Was there debris on the tone wheel?

Yes

Clean tone wheel and sensor. Clear codes and retest.


Perform the ABS VERIFICATION TEST (Refer to 28 - DTC-Based Diagnostics/MODULE, Antilock Brake (ABS)
- Standard Procedure).

No

Replace the Right Front Tone Wheel/Bearing in accordance with the Service Information.
Perform ABS VERIFICATION TEST (Refer to 28 - DTC-Based Diagnostics/MODULE, Antilock Brake (ABS) -
Standard Procedure).

https://dealerconnect.chrysler.com/portal/Controller/Portal 3/3

You might also like