Sun StorageTek™ 2500 Series Array

Hardware Installation Guide

Sun Microsystems, Inc.

www.sun.com

Part No. 820-0015-12

November 2008

Submit comments about this document at: http://www.sun.com/hwdocs/feedback

Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved.
Sun Microsystems, Inc. has intellectual property rights relating to technology that is described in this document. In particular, and without
limitation, these intellectual property rights may include one or more of the U.S. patents listed at http://www.sun.com/patents and one or
more additional patents or pending patent applications in the U.S. and in other countries.
This document and the product to which it pertains are distributed under licenses restricting their use, copying, distribution, and
decompilation. No part of the product or of this document may be reproduced in any form by any means without prior written authorization of
Sun and its licensors, if any.
Third-party software, including font technology, is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in
the U.S. and in other countries, exclusively licensed through X/Open Company, Ltd.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Sun StorEdge, Solaris, Java, Sun StorageTek, and Solstice DiskSuite are
trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S., or its subsidiaries, and in other countries.
All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and in other
countries. Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc.
Legato Networker is a registered trademark of Legato Systems Inc.
Netscape Navigator and Mozilla are trademarks or registered trademarks of Netscape Communications Corporation in the United States and
other countries.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and
applicable provisions of the FAR and its supplements.
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,
ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.

Copyright 2007 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, Californie 95054, Etats-Unis. Tous droits réservés.
Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie qui est décrit dans ce document. En particulier, et sans la
limitation, ces droits de propriété intellectuels peuvent inclure un ou plus des brevets américains énumérés à http://www.sun.com/patents et
un ou les brevets plus supplémentaires ou les applications de brevet en attente dans les Etats-Unis et dans les autres pays.
Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la
décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans
l’autorisation préalable et écrite de Sun et de ses bailleurs de licence, s’il y en a.
Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de caractères, est protégé par un copyright et licencié par des
fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd.
Sun, Sun Microsystems, le logo Sun, AnswerBook2, docs.sun.com, Sun StorEdge, Solaris, Java, Sun StorageTek, et Solstice DiskSuite sont des
marques de fabrique ou des marques déposées de Sun Microsystems, Inc., ou ses filiales, aux Etats-Unis et dans d’autres pays.
Netscape Navigator et Mozilla est une marques de Netscape Communications Corporation aux Etats-Unis et dans d’autres pays.
Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc.
aux Etats-Unis et dans d’autres pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun
Microsystems, Inc.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une license non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciées de Sun qui mettent en place l’interface d’utilisation graphique OPEN LOOK et qui en outre se conforment aux
licences écrites de Sun.
LA DOCUMENTATION EST FOURNIE “EN L’ÉTAT” ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES
OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT
TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE UTILISATION PARTICULIERE OU A
L’ABSENCE DE CONTREFAÇON.
 Contents

Before You Begin ix

1. Tray Overviews 1
Sun StorageTek 2500 Series Array Overview 2
Installation Tasks Checklist 4
Front-Access Components of the Trays 5
LEDs on the Front of the Trays 6
Rear-Access Components of the Trays 8
Controllers 9
Sun StorageTek 2540 Array 10
SFP Transceivers 11
Sun StorageTek 2530 Array 12
Sun StorageTek 2510 Array 13
Controller Tray and Drive Expansion Tray Power-Fan Assembly 14
Sun StorageTek 2501 Expansion Tray 14
Expansion Tray IOM 14
Drive Expansion Tray IOM Ports 15
LEDs on the Rear of the Trays 16
Controller LEDs on the Sun StorageTek 2540 and Sun StorageTek 2510
Arrays 16

iii
 Controller LEDs on the Sun StorageTek 2530 Array 18
Controller Tray and Drive Expansion Tray Power-Fan Assembly LEDs 19
IOM LEDs on the Sun StorageTek 2501 Expansion Tray 20
Disk Drives 22
LEDs on the Disk Drives 24
Common Array Manager Software 25
Service Advisor and Customer-Replaceable Units 26

2. Installing Trays 27
Preparing for the Installation 28
Preparing the Universal Rail Kit 28
Unpacking the Universal Rail Kit 28
Loosening the Rail Adjustment Screws 28
Preparing the Tray 29
Preparing the Cabinet 30
Planning the Order of the Tray Installation 30
Attaching the Rails to a Cabinet 31
Attaching the Universal Rail Kit to a Standard Sun or 19-Inch Cabinet With
Threaded Cabinet Rails 31
Attaching the Universal Rail Kit to a Standard
19-Inch Cabinet With Un-threaded Cabinet Rails 35
Installing a Tray in a Cabinet 41
Connecting the Power Cables 46
Inter-tray Cabling 46
Array Configuration Naming Convention 47
Connecting Drive Expansion Trays 48
Cabling an Expansion Tray to a Controller Tray 49
Cabling an Expansion Tray to Another Expansion Tray 50
Cabling a Third Drive Expansion Tray 51
Tray Interconnect Cable Labeling 53

iv Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 Example Label Abbreviation 53
Single-Controller Configurations 54
Next Steps 54

3. Connecting the Management Host 55

Connecting the Management Host 55
Attaching the Ethernet Ports to the LAN of the Management Host 56
Attaching the Ethernet Ports to the Management Host Using an Ethernet
Hub 56
Attaching the Ethernet Ports Directly to the Management Host With a Cross-
Over Cable 57
Next Steps 57

4. Connecting Data Hosts to the 2510 Array 59

Connecting Data Hosts to the 2510 Array 59
▼ To Connect Host Cables 61
Relocation Cautions 61
Next Steps 62

5. Connecting Data Hosts to the 2530 Array 63

Connecting Data Hosts to the 2530 Array 63
▼ To Connect Data Hosts to a 2530 Array 66
Relocation Cautions 66
Next Steps 67

6. Connecting Data Hosts to the 2540 Array 69

Connecting Data Hosts to the 2540 Array 69
2540 Array Data Host Connection Topologies 70
2540 Array Data Host Connections 73
▼ To Connect Data Hosts Using Fibre Channel 74
Relocation Cautions 74

Contents v
 Next Steps 75

7. Powering On the Array 77

Before Powering On 77
Powering On the Storage Array 78
Powering Off the Array 79
Next Steps 80

8. Data Host HBAs and Software for the 2540 and 2530 Arrays 81
Data Host Software 81
HBAs and Drivers 82
Multipathing 82
Setting Up a Data Host On a Solaris System 82
▼ To Obtain Sun Solaris 9 Data Host Software 83
▼ To Install the SAN 4.4 Data Host Software 84
▼ To Obtain Software for Operating Systems Other Than Solaris 84
Installing Data Host Software for Operating Systems Other Than Solaris 85
About Data Host Software For Non-Solaris Platforms 85
Downloading and Installing Sun RDAC Software 86
Enabling Solaris Multipathing Software 86
▼ Enabling Multipathing Software for Solaris 9 OS 87
▼ Enabling Multipathing Software for Solaris 10 OS 87
Next Steps 88

9. Configuring IP Addressing 89
About IP Addressing 89
Configuring the IP Address of the Controller Modules 89
Configuring Dynamic (DHCP) IP Addressing 90
Configuring Static IP Addressing 91
Using the Serial Port Interface to Assign IP Addresses 91

vi Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 ▼ To Connect a Terminal to the Serial Port 91
▼ To Set Up the Terminal Emulation Program 92
▼ To Establish a Connection With the Serial Port 92
▼ To Configure the IP Addresses 94

A. Configuring iSCSI on the Sun StorageTek 2510 Array 97

Configuring iSCSI Overview 97
iSCSI Concepts 98
Configuring iSCSI - Detailed 99
Preparing for iSCSI and Installing Hardware 99
Configuring iSCSI Tasks 100
Identifying the Target Port IP Address 101
Adding Initiator Information 103
Configuring Other iSCSI Features 104
Additional iSCSI Topics in the Online Help 104
Configuring Mutual Authentication for an iSCSI Session 105
▼ To Configure Mutual Authentication 105

B. iSCSI Configuration Example

Using Solaris 107
▼ To Prepare for the iSCSI Configuration 107
▼ To Configure iSCSI 108

C. iSCSI Configuration Example

Using Windows 111
▼ To Prepare for the iSCSI Configuration 111
▼ To Configure iSCSI on Windows 112

D. Connecting to the 2510 Array with Other Topologies 121

Connecting to the 2510 Array with Other Topologies 121
Host Cabling Configurations – Single Controller 122

Contents vii
 Host Cabling Configurations – Dual Controller 124

E. Using DC Power 127

DC Power Overview 127
Installation Notes for DC Power 129
Ship Kit Changes 129
DC Power LEDS 130
Connecting Power Cables 130
▼ Connecting the Cables 131
Turning Off the DC Power During an Emergency 132
Relocation Cautions 132

F. Configuring a DHCP Server 133

Before You Begin 133
Setting Up a Solaris DHCP Server 133
Setting Up a Windows 2000 Advanced Server 138
Installing the DHCP Server 139
Configuring the DHCP Server 139

Glossary 143

Index 151

viii Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Before You Begin

Refer to the following documents to make sure physical dimensions, service

clearances, and power connections are ready for the installation of your Sun
StorageTek 2500 Series array.
■ Sun StorageTek 2500 Series Array Regulatory and Safety Compliance Manual
■ Sun StorageTek 2500 Series Array Site Preparation Guide

About this Guide

This Sun StorageTek 2500 Series Array Hardware Installation Guide describes how to
install rack-mounting rails and array trays in a cabinet.

The terminology used in this document refers to the Sun StorageTek 2500 Series
arrays. There are three styles of controller trays, each with different host interface
ports (iSCSI, SAS, or FC). There is also the drive expansion tray, which enables the
Sun StorageTek 2500 Series arrays to have more disk drives attached. The
components that slide into the trays are called CRUs or modules. The terms you
might see in this document are: controller (or controller module), power-fan module,
I/O module, and disk drive.

This document provides information to physically setup and connect your array to a
host. Afterwards, information is provided to apply power and to add network
functionality, including storage management (multipath/failover), IP addressing,
iSCSI, and DHCP.

Array management, data host management, and remote command line interface
(CLI) functions are performed by the Sun StorageTek Common Array Manager
(CAM) software. For installation and initial configuration of the Sun StorageTek 2500

ix
 Series array, including firmware upgrades, initial array setup, partitioning domains,
configuring storage, and configuring IP addressing, see the Sun StorageTek Common
Array Manager Software Installation Guide.

Related Documentation
Application Title Part Number

Site planning information Sun StorageTek 2500 Series Array Site 820-0024-nn
Preparation Guide
Late-breaking information not Sun StorageTek 2500 Series Array Release 820-3511-nn
included in the information set Notes
Sun StorageTek Common Array Manager 820-2935-nn
Release Notes
Instructions for installing the Sun StorageTek Common Array Manager 819-2934-nn
CAM host management Software Installation Guide
software
Quick reference information Sun StorageTek 6130, 2500 Series, and 6540 820-2932-nn
for the CLI Arrays sscs(1M) CLI Quick Reference
Regulatory and safety Sun StorageTek 2500 Series Array Regulatory 820-0025-nn
information and Safety Compliance Manual
Instructions for installing an Sun StorageTek Expansion Cabinet 805-3067-nn
expansion cabinet Installation and Service Manual
Instructions for installing the Sun Rack Installation Guide 816-6386-nn
Sun Rack 900/1000 cabinets

In addition, the Sun StorageTek 2500 Series Array includes the following online
documentation:
■ Sun StorageTek Common Array Manager online help contains system overview
and configuration information.
■ Service Advisor provides guided FRU replacement procedures with system
feedback. You can access Service Advisor from the Sun StorageTek Common
Array Manager software.
■ sscs man page commands for the CLI provides help on man page commands
available on a management host or on a remote CLI client.

x Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Documentation, Support and Training
You can view, print, or purchase a broad selection of other Sun documentation,
including localized versions, at:

http://www.sun.com/documentation

Support information for this product can be found at:

http://www.sun.com/support

Training information for this product can be found at:

http://www.sun.com/training/

If you have technical questions about this product that are not answered in this
document, go to:

http://www.sun.com/service/contacting

Sun Welcomes Your Comments

Sun is interested in improving its documentation and welcomes your comments and
suggestions. You can submit your comments by going to:

http://www.sun.com/hwdocs/feedback

Please include the title and part number of your document with your feedback:

Sun StorageTek 2500 Series Array Hardware Installation Guide, part number 820-0015-12.

Before You Begin xi

xii Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 1

Tray Overviews

This chapter describes the process of installing the Sun StorageTek 2500 Series Array.
It contains the following sections:
■ “Sun StorageTek 2500 Series Array Overview” on page 2
■ “Installation Tasks Checklist” on page 4
■ “Front-Access Components of the Trays” on page 5
■ “LEDs on the Front of the Trays” on page 6
■ “Rear-Access Components of the Trays” on page 8
■ “LEDs on the Rear of the Trays” on page 16
■ “Disk Drives” on page 22
■ “LEDs on the Disk Drives” on page 24
■ “Common Array Manager Software” on page 25
■ “Service Advisor and Customer-Replaceable Units” on page 26

1
 Sun StorageTek 2500 Series Array
Overview
The Sun StorageTek 2540 Array, the Sun StorageTek 2530 Array, the Sun StorageTek
2510 Array, and the Sun StorageTek 2501 Expansion Tray are a family of storage
products that provide high-capacity, high-reliability storage in a compact
configuration.

The Sun StorageTek 2500 Series Array is a modular, rack-mountable controller tray.
It is scalable from a single controller tray configuration to a maximum configuration
of one controller tray and three additional drive expansion trays. This would create
a storage array configuration with a total of 48 drives attached behind the controllers
(one controller tray and three drive expansion trays).

All four of the trays can be installed in the following cabinets:

■ Sun Rack 900/1000 cabinet
■ Sun StorageTek Expansion cabinet
■ Any 19-inch wide, 4-post, EIA-compatible rack or cabinet with a front-to-back
depth between vertical cabinet rails of 61cm to 91cm (24 in. to 36 in.). The cabinet
can have threaded or un-threaded cabinet rails.

The Sun StorageTek 2540 Array, the Sun StorageTek 2530 Array and the Sun
StorageTek 2510 Array contains disk drives for storing data. The controller tray,
typically with two controller modules, provides the interface between a data host
and the disk drives. The Sun StorageTek 2540 Array provides a Fibre Channel
connection between the data host and the controller tray. The Sun StorageTek 2530
Array provides a Serial Attached SCSI (SAS) connection between the data host and
the controller tray. The Sun StorageTek 2510 Array provides iSCSI connections using
Ethernet between the data host and the controller tray.

The Sun StorageTek 2501 drive expansion tray provides additional storage. You can
attach the drive expansion tray to any of the 2500 series arrays.

You manage the array with the Sun StorageTek Common Array Manager software.

2 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 FIGURE 1-1 Sun StorageTek 2500 Series Array Connection Example Using Fibre Channel

Data hosts

Ethernet out-of-band
Host 1
Redundant Fibre Channel

Host 2

FC switch

Host 3

FC switch Host 4

Host 5

Expansion trays

Controller tray

Remote
Local
management host
management host

Chapter 1 Tray Overviews 3

 Installation Tasks Checklist
The following checklist (TABLE 1-1) outlines the tasks required for installing the Sun
StorageTek 2500 Array hardware and tells you where you can find detailed
procedures. To ensure a successful installation, perform the tasks in the order in
which they are presented.

Before you begin to install the array, do the following:

■ Read the Sun StorageTek 2500 Series Array Release Notes for any late-breaking
information related to the installation of the array.
■ Prepare the site as described in these books:
■ Sun StorageTek 2500 Series Array Regulatory and Safety Compliance Manual
■ Sun StorageTek 2500 Series Array Site Preparation Guide

The Sun StorageTek 2500 Series Array Site Preparation Guide has information about the
physical dimensions of the trays as well as the service clearance and the power
requirements of the cabinet. This document should be used to prepare your site
layout prior to the installation.

TABLE 1-1 Sun StorageTek 2500 Series Array Hardware Installation Checklist

Step Installation Task Where to Find Procedure

1. Review the hardware overview in

this chapter.
2. Unpack the cabinet and move it Unpacking guide attached to the outside of the
into position. shipping carton
3. Install and secure the cabinet. • Sun StorageTek Expansion Cabinet Installation and
Service Manual
• Sun Rack Installation Guide
4. Unpack the rackmounting kit and “Preparing the Universal Rail Kit” on page 28
check its contents.
5. Unpack the tray box and check its “Preparing the Tray” on page 29
contents.
6. Prepare the cabinet for installation. “Preparing the Cabinet” on page 30
7. Attach the rails to the cabinet. “Attaching the Rails to a Cabinet” on page 31
8. Mount the controller tray and “Installing a Tray in a Cabinet” on page 41
expansion trays in the cabinet.
9. Attach the power cables. “Connecting the Power Cables” on page 46

4 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
TABLE 1-1 Sun StorageTek 2500 Series Array Hardware Installation Checklist

Step Installation Task Where to Find Procedure

10. Cable the controller tray and “Inter-tray Cabling” on page 46

expansion trays.
11. Connect the management host. “Connecting the Management Host” on page 55
12. Connect the data hosts. “Connecting Data Hosts to the 2510 Array” on
page 59
“Connecting Data Hosts to the 2530 Array” on
page 63
“Connecting Data Hosts to the 2540 Array” on
page 69

13. Turn on the power. “Powering On the Storage Array” on page 78

When the tasks in TABLE 1-1 are complete, you can install the Common Array
Manager software on an external management host, install and upgrade firmware
from the management host, and perform initial array setup and system
configuration. See the Sun StorageTek Common Array Manager Software Installation
Guide for complete information on software-related tasks. For iSCSI configuration,
see Appendix A.

Front-Access Components of the Trays

Components that are accessed through the front of the Sun StorageTek 2540 Array,
the Sun StorageTek 2530 Array, and the Sun StorageTek 2510 Array are identical in
appearance.

The front-access components include the following:

■ End caps – Plastic, removable caps on the right and left side of the tray. Numbers
on the side of the right end cap indicate the numbering of the drives.
■ Disk drives – Twelve removable disk drives
■ LEDs (light emitting diodes) – Four LEDs located on the left-side end cap

Chapter 1 Tray Overviews 5

 FIGURE 1-2 Front-Access Components on the Controller Tray and the Drive Expansion
Tray

3
1. End Caps
2. Disk Drives
3. Tray LEDs

1 2 1

LEDs on the Front of the Trays

The four LEDs on the front of the Sun StorageTek 2540 Array, the Sun StorageTek
2530 Array, the Sun StorageTek 2510 Array, and the Sun StorageTek 2501 Expansion
tray are identical in appearance and function. The LEDs are located on the left-side
endcap of the tray.

6 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 FIGURE 1-3 Location of the LEDs on the Front of the Trays

TABLE 1-2 Description of the LEDs on the Front of the Trays

Location LED Color On Off

1 Locate White The locate light is turned on Normal condition
manually by CAM to help you
find the tray that requires
attention.
2 Service Action Amber A component within the tray The components in the tray
Required (Fault) requires attention. are operating normally.
3 Over Amber The tray temperature has reached The tray temperature is
Temperature the high-end of its operating within operational range.
range and requires attention.
4 Power Green Tray is powered on. Tray is not powered on.

Chapter 1 Tray Overviews 7

 Rear-Access Components of the Trays
This section reviews the components that can be accessed from the back of a:
■ Sun StorageTek 2500 Series controller tray
■ Sun StorageTek 2501 drive expansion tray

Sun StorageTek 2500 Series Array

Components that are accessed from the rear of the Sun StorageTek 2500 Series Array
controller trays include:
■ Controller Modules – Two removable controller modules (controllers), typically
identified as Controller A (on the left) and Controller B (on the right).
■ Power-fan assemblies – Two removable power supply modules with cooling
fans. The power-fan assembly is identical and interchangeable to the power-fan
assemblies used for Sun StorageTek 2501 drive expansion tray.

FIGURE 1-4 Controller Tray Rear-Access Components

1

1. Controller Modules
2 2. Power-Fan Assemblies

8 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Sun StorageTek 2501 Drive Expansion Tray

Components that are accessed from the rear of the Sun StorageTek 2501 Drive
Expansion Tray are:
■ I/O Modules (IOMs) – Two removable input/output modules
■ Power-fan assemblies – Two removable power supply modules with cooling
fans. The power-fan assembly is identical and interchangeable with all power-fan
assemblies used in the 2500 Series trays.

FIGURE 1-5 Drive Expansion Tray Rear-Access Components

1. I/O Modules
2 2. Power-Fan Assemblies

Controllers
The Sun StorageTek 2540, 2530, and 2510 Arrays usually have two controllers
(single-controller configurations are available, but are not recommended). The
controllers manage the input/output (I/O) between the volumes and the data host.
The controllers have an Ethernet connection to the management host for out-of-band
management and contain a battery that provides backup power to the cache memory
for up to three days in the event of a power loss.

Because each controller tray contains two controllers, the data path through one
controller can fail and the other controller provides a redundant data path to all of
the disk drives. If a controller fails, you can replace the failed controller while the
power is applied and the storage array is processing data (a hot swap).

Note – Replacement controllers might not be at the same level of firmware. If

necessary, use CAM to upgrade the firmware for the new controller so that it
matches the configuration database (baseline firmware release level or later).

Chapter 1 Tray Overviews 9

 Each controller has a media access control (MAC) address that identifies it on the
network. The MAC address for a controller is on a label on the controller. The MAC
address label is attached to the controller at the rear of the tray near the serial port.

The tray ID numbers are set by the trays themselves on first power on. However,
you can change the setting through the Common Array Manager software. The tray
ID numbers on both of the controllers in one controller tray are identical under
optimal operating conditions.

Sun StorageTek 2540 Array

This Fibre Channel (FC) controller tray provides the following capabilities:
■ Two Fibre Channel data host ports per controller with 1, 2, or 4 Gb/s data host
connection speed
■ One drive expansion tray Serial Attached SCSI (SAS) port with 3 Gb/s drive
expansion tray connection speed
■ 512-MB or 1-GB mirrored cache
■ Maximum connection of 48 disk drives (one controller tray and three drive
expansion trays)

When fiber-optic cables are used to connect to the data host, a Small Form-factor
Pluggable (SFP) transceiver is required to make the connection.

FIGURE 1-6 Sun StorageTek 2540 Array Ports

1. Drive Expansion Tray Port (SAS

Out)
2. Ethernet Management Host Port
3. Fibre Channel Data Host Ports
4. RS-232 Port (Serial Port)
5. Not Used

10 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 SFP Transceivers
You can connect the Sun StorageTek 2540 Array to either copper host interface cables
or fiber optic host interface cables. If you use fiber-optic cables, you must install an
SFP transceiver in each interface port on the controller where a fiber-optic cable is to
be installed. The SFP transceiver is required to translate the optical signals from the
fiber-optic cable into digital signals for the controller.

Note – The SFP transceiver shown might look different from those that are shipped
with your controller tray. The difference does not affect transceiver performance.

FIGURE 1-7 SFP Transceiver for the Sun StorageTek 2540 Array

3 1. Data Host Port

2. SFP Transceiver
3. Fiber-Optic Cable
2

Chapter 1 Tray Overviews 11

 Sun StorageTek 2530 Array
This SAS controller tray provides the following capabilities:
■ Three SAS host ports with 3 Gb/s host connection speed
■ One drive expansion tray SAS port for the drive channel with 3 Gb/s drive
expansion tray connection speed
■ 512-MB or 1-GB mirrored cache
■ Maximum connection of 48 disk drives (one controller tray and three drive
expansion trays)

FIGURE 1-8 Sun StorageTek 2530 Array Controller Ports

1. Drive Expansion Tray

Port (SAS Out)
2. Ethernet Management
Host Port
3. SAS Data Host Ports
4. RS-232 Port (Serial
Port)

12 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Sun StorageTek 2510 Array
This iSCSI controller tray provides the following capabilities:
■ Two iSCSI Ethernet host ports with 1 Gigabit per second host connection speed
■ One drive expansion tray SAS port for the drive channel with 3 Gb/s drive
expansion tray connection speed
■ 512-MB or 1-GB cache on each controller
■ Maximum connection of 48 disk drives (one controller tray and three drive
expansion trays)

FIGURE 1-9 Sun StorageTek 2510 Array Ports

1. Drive Expansion Tray Port

(SAS Out)
2. Ethernet Management Host
Port
3. Ethernet Data Host Ports
4. RS-232 Port (Serial Port)
5. Not Used

Chapter 1 Tray Overviews 13

 Controller Tray and Drive Expansion Tray Power-
Fan Assembly
The power-fan assembly for the Sun StorageTek 2540 Array, the Sun StorageTek 2530
Array, and the Sun StorageTek 2510 Array is identical and interchangeable.

Note – A minimum of two disk drives must be operating in a controller tray or in a

drive expansion tray to avoid generating a power-fan assembly error.

The power-fan assembly contains an integrated cooling fan. The power supply
provides power to the internal components by converting incoming AC voltage to
DC voltage. The fan circulates air inside of the tray by pulling air in through the
vents on the front of the assembly and pushing the air out of the vents on the back
of each fan.

Each tray contains two power-fan assemblies. If one power supply is turned off or
malfunctions, the other power supply maintains electrical power to the tray.
Likewise, the fans provide redundant cooling. If one of the fans in either fan housing
fails, the remaining fan continues to provide sufficient cooling to operate the tray.
The remaining fan runs at a higher speed until the failed fan is replaced. Replace the
failed fan as soon as possible.

Sun StorageTek 2501 Expansion Tray

The drive expansion tray expands the storage capacity of a storage array. The
controllers in the controller tray can connect to the drive expansion tray and access
the disk drives in the drive expansion tray for additional storage. A drive expansion
tray contains both physical components (disk drives, Input/Output Modules
(IOMs), and power-fan assemblies) and logical components (virtual disks and
volumes).

Expansion Tray IOM

The expansion tray contains two IOMs that provide the interface between the disk
drives in the expansion tray and the controllers in the controller tray. Each controller
in the controller tray connects to an IOM.

If one IOM fails, the other IOM provides a redundant data path to the disk drives.
You can replace a failed IOM while the power to the storage array is turned on and
the storage array is processing data (a hot swap).

14 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Drive Expansion Tray IOM Ports
The IOM uses SAS cables to enable the controller tray to communicate with the disk
drives in the drive expansion trays. Each IOM in a drive expansion tray has two SAS
expansion ports. One port shows an up arrow, and the other port shows a down
arrow.

FIGURE 1-10 SAS Ports on the Expansion Tray IOM

1. SAS Port (Up Arrow)

2. SAS Port (Down Arrow)
3. Serial Port

When connecting the SAS cable from an IOM in one drive expansion tray to an IOM
in another drive expansion tray, connect from a port with a down arrow to a port
with an up arrow.

Note – If the cable is plugged into two ports with arrows of the same direction,
communication between the two drive expansion trays is lost.

Chapter 1 Tray Overviews 15

 LEDs on the Rear of the Trays

Controller LEDs on the Sun StorageTek 2540 and

Sun StorageTek 2510 Arrays
FIGURE 1-11 Locations of the Controller LEDs on the Sun StorageTek 2540 and 2510 Arrays

TABLE 1-3 Descriptions of the Controller LEDs on the 2540 and 2510 Arrays

Location LED Color On Off

1 Link Fault Amber At least one link has an error. Normal condition
2 Drive Link Green At least one link is active. At least one link has an error
3 Battery Fault Amber Indicates a fault within the Normal condition
battery backup unit.
4 Cache Active Green Caching is enabled. Indicates a problem if caching is
When blinking, the cache has enabled.
data.
5 Service Action Blue The controller can be removed The controller cannot be
Allowed from the controller tray. removed from the controller
tray.
6 Service Action Amber Indicates a fault within the Normal condition
Required (Fault) controller.
7 Power Green Tray is powered on. Tray is not powered on.
8 Ethernet Link Green The connection is active. The connection is not active.
9 Ethernet Green 100BASE-TX connection is The 100BASE-TX connection is
100BASE-TX active. not active.

16 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 TABLE 1-3 Descriptions of the Controller LEDs on the 2540 and 2510 Arrays

Location LED Color On Off

10 and 11 Host Link (2540) Green Both LEDs on indicate a 4-Gb/s Both LEDs off indicate no link
data rate from the management to the management software
software host. host.
Left LED on and right LED off
indicate a 1-Gb/s data rate from
the management software host.
Right LED on and left LED off
indicate a 2-Gb/s data rate from
the management software host.
10 Ethernet Link Green The connection is active. The connection is not active.
(2510)
11 Ethernet Green 1000BASE-TX connection is The 1000BASE-TX connection
1000BASE-TX active. is not active.
(2510)

Controller LEDs on the Sun StorageTek 2530

Array
FIGURE 1-12 Locations of the Controller LEDs on the Sun StorageTek 2530 Array

TABLE 1-4 Descriptions of the Controller LEDs on the Sun StorageTek 2530 Array (1 of

Location LED Color On Off

1 Link Green At least one link is active. All links have failed.
2 Link Fault Amber At least one link has an error. Normal condition.
3 Battery Fault Amber Indicates a fault within the Normal condition.
battery backup unit.

Chapter 1 Tray Overviews 17

 TABLE 1-4 Descriptions of the Controller LEDs on the Sun StorageTek 2530 Array (2 of

Location LED Color On Off

4 Cache Active Green Caching is enabled. Indicates a problem if caching is
When blinking, the cache has enabled.
data.
5 Service Action Blue The controller can be removed The controller cannot be
Allowed from the controller tray. removed from the controller tray.
6 Service Action Amber Indicates a fault within the Normal condition
Required (Fault) controller.
7 Power Green Tray is powered on. Tray is not powered on.
8 Ethernet Link Green The connection is active. The connection is not active.
9 Ethernet Green 100BASE-TX connection is The 100BASE-TX connection is
100BASE-TX active. not active.

18 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 Controller Tray and Drive Expansion Tray Power-
Fan Assembly LEDs
The power-fan assembly LEDs for the Sun StorageTek 2540 Array, the Sun
StorageTek 2530 Array, the Sun StorageTek 2510 Array, and the Sun StorageTek 2501
drive expansion tray are identical.

FIGURE 1-13 Locations of the Power-Fan Assembly LEDs

TABLE 1-5 Descriptions of the Power-Fan Assembly LEDs

Location LED Color On Off

1 DC Power (DC Good) Green DC power from the DC power from the power-
power-fan assembly is fan assembly is not
available. available.
2 Service Action Allowed Blue The power-fan assembly The power-fan assembly
can be removed from the cannot be removed from the
tray. tray.
3 Fault Amber A fault exists within the Normal condition
power-fan assembly.
4 Power (AC Good) Green The assembly is powered The assembly is not
on. powered on.

Chapter 1 Tray Overviews 19

 IOM LEDs on the Sun StorageTek 2501 Expansion
Tray
FIGURE 1-14 Locations of the IOM LEDs

TABLE 1-6 Descriptions of the IOM LEDs

Location LED Color On Off

1 IOM Link Fault Amber A link error occurred. No errors have occurred.
2 IOM Link Green The link is active. A link error occurred.
Service Action Blue The IOM can be removed The IOM cannot be removed
3 Allowed from the drive expansion tray. from the drive expansion
tray.
Service Action Amber A fault exists within the IOM. Normal condition
4
Required (Fault)
5 Power Green The IOM tray is powered on. The IOM is not powered on.

20 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Service Action LEDs
Each controller, power-fan assembly, IOM, and disk drive has a Service Action
Allowed LED. The Service Action Allowed LED indicates when you can remove a
component safely. See “LEDs on the Rear of the Trays” on page 16 for the locations
and descriptions of the Service Action Allowed LEDs on a controller tray and a drive
expansion tray, and see “LEDs on the Disk Drives” on page 24 for disk drive Service
Allowed LEDs.

Caution – Potential loss of data access – Never remove a power-fan assembly, a

controller module, or a disk drive unless the Service Action Allowed LED is turned
on or you are given specific instructions to do so by the Service Advisor feature of
the Common Array Manager software.

If a CRU or module fails and must be replaced, the Service Action Required LED on
that module turns on to indicate that a service action is required. The Service Action
Allowed LED turns on if it is safe to remove the CRU or module. If there are data
availability dependencies or other conditions that dictate that a CRU or module
should not be removed, the Service Action Allowed LED remains off.

The Service Action Allowed LED automatically turns on or turns off as conditions
change. In most cases, the Service Action Allowed LED turns on when the Service
Action Required (Fault) LED is turned on for a CRU or module.

Note – If the Service Action Required (Fault) LED is turned on but the Service
Action Allowed LED is turned off for a particular CRU or module, you might have
to service another component first. Check the Service Advisor feature of the
Common Array Manager software to determine the action you should take.

Chapter 1 Tray Overviews 21

 Disk Drives
Disk drives for the Sun StorageTek 2500 Series Array have three components:
■ Hard drive
■ Hard drive carrier
■ Adapter card for connecting the disk drive to the mid-plane

The disk drives can be Serial Advance Technology Attachment (SATA) disk drives,
Fibre Channel (FC) disk drives, or SAS disk drives.

Controller trays or drive expansion trays hold up to 12 disk drives, for a maximum
of 48 disk drives in a storage array. To reach the maximum of 48 disk drives, the
storage array must consist of one controller tray and three drive expansion trays.

Access to disk drives is from the front of the tray.

Refer to the storage array release notes for supported drives.

Disk drives can be mixed, provided you adhere to these additional rules:
■ Use the same drive types within a virtual disk
■ Assign hot spares to cover any disk drive failure

22 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 1-15 Disk Drives

The physical locations of the disk drives are numbered 1 through 12, from left to
right, and from top to bottom. The right end cap has numbers on the side showing
the numbers of the adjacent drives. The Service Advisor feature of the Common
Array Manager software automatically detects a disk drive’s tray ID and slot
designation.

Chapter 1 Tray Overviews 23

 LEDs on the Disk Drives
FIGURE 1-16 Locations of the Disk Drive LEDs

1
2

TABLE 1-7 Descriptions of the Disk Drive LEDs

Location LED Color General Behavior

Service Action Blue On – The disk drive can be removed from the tray.
1 Allowed Off – The disk drive cannot be removed from the
tray.
Fault Amber On – The disk drive has a problem.
2
Off – Normal condition.
Power Green Off – The power is turned off.
On – The power is on and the disk drive is operating
3 normally.
On and blinking (0.5 s on, 0.5 s off) –Disk drive
I/O activity is taking place.

24 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 TABLE 1-8 Disk Drive States Represented by the LEDs

Power Fault
Disk Drive State
(Green LED) (Amber LED)
Power is not applied. Off Off
Normal operation, power is turned on, no disk drive I/O activity is On, solid Off
occurring.
Normal operation, disk drive I/O activity is occurring. On, blinking Off
Service action required, a fault condition exists, and the disk drive is On, solid On, solid
offline.

Common Array Manager Software

The Sun StorageTek 2500 Series Array is managed by the Sun StorageTek Common
Array Manager software. The Common Array Manager provides web browser–
based management and configuration from an external management host, data host
software that controls the data path between the data host and the array, and a
remote command-line interface (CLI) client that provides the same control and
monitoring capability as the web browser, and is scriptable for running frequently
performed tasks.

The Common Array Manager software includes Service Advisor, an online reference
full of hardware and software configuration and troubleshooting information and
procedures.

For information about installing the Common Array Manager software and
configuring and managing the array, see the Sun StorageTek Common Array Manager
Software Installation Guide.

Chapter 1 Tray Overviews 25

 Service Advisor and Customer-
Replaceable Units
The majority of replaceable units are designed to be replaceable by customers.

To see a list of the hardware components that can be replaced at the customer site
refer to Service Advisor in the Sun StorageTek Common Array Manager software.

The Service Advisor also provides information and procedures for replacing array
components.

Note – The replaceable components inside your controller tray or drive expansion
tray are referred to as either customer replaceable units (CRUs) or as modules.

26 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 2

Installing Trays

Use the procedures in this chapter to install trays in a cabinet. The number of trays
you need to install depends on your overall storage requirements. You can install a
maximum of four trays, one controller tray and up to three drive expansion trays for
each array.

This chapter describes the process of installing the Sun StorageTek 2500 Series Array.
It contains the following sections:
■ “Preparing for the Installation” on page 28
■ “Attaching the Rails to a Cabinet” on page 31
■ “Installing a Tray in a Cabinet” on page 41
■ “Connecting the Power Cables” on page 46
■ “Inter-tray Cabling” on page 46
■ “Tray Interconnect Cable Labeling” on page 53
■ “Single-Controller Configurations” on page 54
■ “Next Steps” on page 54

The installation procedures in this chapter require the following items:

■ #2 Phillips screwdriver (minimum 4-inch length recommended)
■ #3 Phillips screwdriver (minimum 4-inch length recommended)
■ Antistatic protection

Caution – Electrostatic discharge can damage sensitive components. Touching the

array or its components without using a proper ground might damage the
equipment. To avoid damage, use proper antistatic protection before handling any
components.

27
 Preparing for the Installation
Use the following procedures to prepare for installation:
■ “Preparing the Universal Rail Kit” on page 28
■ “Preparing the Tray” on page 29
■ “Preparing the Cabinet” on page 30

Preparing the Universal Rail Kit

Use the universal rail kit, ordered separately, to mount the Sun StorageTek 2500
Series Array trays in any of the following cabinets:
■ Any standard Sun cabinet, such as the Sun Rack 900/1000 cabinet
■ Any 19-inch wide, 4-post, EIA-compatible rack or cabinet with a front-to-back
depth between vertical cabinet rails of 24-36 inches (with threaded or un-threaded
cabinet rails).
■ The Sun StorageTek Expansion cabinet

Unpacking the Universal Rail Kit

Unpack the universal rail kit and check the contents.

The universal rail kit (part number 594-2489-02) comes with pre-assembled rails and
contains the following items:
■ Left rail assembly
■ Right rail assembly
■ 10 8-32x3/8” pinhead screws with lock washers
■ 4 M4 flathead screws
■ 4 cabinet rail adapter plates (used for un-threaded cabinet rails only)

Loosening the Rail Adjustment Screws

To loosen the adjustment screws on the left and right rails:

Use a flathead screwdriver to loosen the two rail adjustment screws on each rail to
allow adjustment of each rail length ().

28 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 2-1

Note – The rails are pre-configured to adjust to cabinet rail depths of between 24
inches (609.6mm) and 34 inches (863.6mm).

Preparing the Tray

Caution – Two people are needed to lift and move the tray. Use care to avoid injury.
A tray can weigh up to 54.3 pounds (24.6 kg).

1. Unpack the tray.

2. Check the contents of the box for the following items:

■ Sun StorageTek 2500 Series Array trays (controller or drive expansion)
■ Ship kit for the controller tray
■ One pair left and right end caps (plastic bezels)
■ Four 4Gbps FC SFPs (2 per FC controller module - ST2540 Array only)
■ One 6-meter RJ45 -RJ45 Ethernet cables
■ One RJ45-DIN9 cable
■ One RJ45-DB9 adapter
■ One RJ45-DB9 null modem adapter
■ Sun StorageTek Common Array Manager Software CD
■ Sun StorageTek Common Array Manager Software Installation Guide (on the
software CD)
■ Common Array Manager sscs CLI Quick Reference Card
■ Sun StorageTek 2500 Series Array Hardware Installation Guide (Hardcopy)
■ Accessing Documentation guide
■ Premium feature license cards (ordered optionally)
■ Ship kit for each expansion tray
■ Two 1-meter copper SAS cables (one per I/O module)
■ Accessing Documentation guide

AC power cords are shipped separately with each tray.

Chapter 2 Installing Trays 29

 Preparing the Cabinet
Select the cabinet in which you will be installing the array. Be sure the cabinet is
installed as described in the installation instructions provided with it.
1. Stabilize the cabinet as described in the cabinet documentation.
2. If the cabinet has casters, make sure the casters are locked to prevent the
cabinet from rolling.
3. Remove or open the front panel.
4. Remove or open the vented back panel.

Planning the Order of the Tray Installation

Install the trays starting with the controller tray at the lowest available 2U tray slot
in the cabinet. Next, install the expansion trays for the first controller tray. If room
remains in the cabinet, repeat for the next controller tray and expansion trays.

Starting at the bottom distributes the weight correctly in the cabinet.

Tip – If you plan on adding hosts to the cabinet, make sure that you have cables of
sufficient length to reach their controller tray.

Attaching the Rails to a Cabinet

Depending on the type of cabinet in which you will install the tray, use one of the
following procedures to attach the rails:
■ “Attaching the Universal Rail Kit to a Standard Sun or 19-Inch Cabinet With
Threaded Cabinet Rails” on page 31
■ “Attaching the Universal Rail Kit to a Standard 19-Inch Cabinet With Un-
threaded Cabinet Rails” on page 35

Each tray requires two standard mounting rack units (2RU) of vertical space in the
cabinet. Most cabinets have a “U” mark on their vertical rail with three mounting
holes in the left cabinet vertical rail and in the right cabinet vertical rail. The top
mounting hole of the lower RU is always closest to the bottom mounting hole of the
upper RU, hence the division between RUs on a cabinet rail is between the two
closest mounting holes in a grouping.

The universal rails have an adjustable depth of 24” to 34”.

30 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Attaching the Universal Rail Kit to a Standard
Sun or 19-Inch Cabinet With Threaded Cabinet
Rails
This procedure describes the steps to attach the universal rail kit to:
■ All standard Sun cabinets, including the Sun Rack 900/1000 cabinets
■ Sun StorageTek Expansion cabinets
■ All 19-inch wide, 4-post EIA-compatible racks and cabinets with the following
cabinet rail types:
■ M5 threaded
■ M6 threaded
■ 10-32 threaded
■ 12-24 threaded
■ circular un-threaded

1. To attach the universal rail kit to a cabinet with these cabinet rail types, position
the front flange of the left universal rail behind the left front cabinet rail
(FIGURE 2-2).

Note – The U marks are not labeled on all racks, as they are on the Sun cabinets.
The rule of thumb to remember is that the division of RUs passes between the two
closest rail holes in each set of holes (see FIGURE 2-2).

Chapter 2 Installing Trays 31

 FIGURE 2-2 Positioning the Front of the Left Rail Behind the Left Front Cabinet Rail

2. Insert the 8-32 screws through the center holes in each RU of the rack into the
top and bottom holes in the Universal rail ().
These screws pass through the cabinet rail holes and screw into threaded holes in
the Universal rail.

FIGURE 2-3

3. Repeat Step 1 and Step 2 for the right rail.

4. At the back of the cabinet, adjust the length of the left rail as needed to fit the
cabinet, and position the rail flange behind the face of the cabinet rail
(FIGURE 2-4).

32 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 2-4 Adjusting the Length of the Left Rail at the Back of the Cabinet

5. Align the rail flange so that the top and bottom mounting holes match the
center holes in the RUs corresponding to those used on the front of the cabinet.

Chapter 2 Installing Trays 33

 6. Insert the 8-32 screws through the center holes of the rack into the top and
bottom mounting holes on the universal rail (FIGURE 2-5).

FIGURE 2-5 Securing the Left Rail to the Back of the Cabinet

7. Repeat Step 4, Step 5, and Step 6 for the right rail.

Attaching the Universal Rail Kit to a Standard

19-Inch Cabinet With Un-threaded Cabinet Rails
This procedure describes the steps to attach the universal rail kit to:

34 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
■ All 19-inch wide, 4-post EIA-compatible racks and cabinets with un-threaded
cabinet rails (square hole racks).

To attach the universal rail kit to a cabinet with un-threaded cabinet rails, follow
these steps first for the left rail and then for the right rail:

1. Hook a cabinet rail adapter plate over the front of the cabinet rail. (FIGURE 2-6)

FIGURE 2-6 Inserting the Cabinet Rail Adapter Plate on the Cabinet Rail

Position the adapter plate over of the 2RU slot in which the tray is to be mounted.
The hook on the top of the adapter plate hooks into the top hole of the upper RU.
The flat flange on the bottom of the adapter plate fits into the bottom hole of the
lower RU (FIGURE 2-7).

Chapter 2 Installing Trays 35

 FIGURE 2-7 Adapter Plate in Place on the Cabinet Rail

2. Slide the front flange of the universal rail between the front cabinet rail and
the top hook of the rail adapter plate (FIGURE 2-8).

FIGURE 2-8 Sliding the Flange of the Universal Rail Behind the Cabinet Rail

36 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
3. Insert and tighten two 8-32 screws through the top and bottom holes in the
adapter plate, through the cabinet rail, and into the top and bottom threaded
holes in the universal rail mounting flange (FIGURE 2-9).

FIGURE 2-9 Securing the Rail to the Front left of the Cabinet

4. Repeat Step 1 through Step 3 on the corresponding cabinet rail at the back of
the cabinet (FIGURE 2-10).
Mounting the rail on the back of the cabinet is the same as mounting it to the
front, after you extend the rail the necessary length to reach the rear cabinet rail.

Chapter 2 Installing Trays 37

 FIGURE 2-10 Adjusting the Length of the Rail at the Back of the Cabinet

5. Insert and tighten two 8-32 screws through the top and bottom holes in the
adapter plate, back cabinet rail, and universal rail mounting flange
(FIGURE 2-11).
The screws passes through the unthreaded holes of the adapter plate and cabinet
rail mounting rail and screw into the threaded holes of the rail mounting flange.

38 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 2-11 Securing the Rail to the Back of the Cabinet

For extra stability, you can tighten the rail screws as in .

6. Repeat Step 1 through Step 5 to install the right rail.

Installing a Tray in a Cabinet

Install the controller tray in the first empty 2RU slot at the bottom of the cabinet. If
you are installing expansion trays, continue installing the trays from the bottom up.
1. Using two people, one at each side of the tray, carefully lift and rest the tray on
the bottom ledge of the left and right rails (FIGURE 2-12).

Caution – Use care to avoid injury. A tray can weigh up to 55 pounds (25 kg).

Chapter 2 Installing Trays 39

 FIGURE 2-12 Positioning the Controller Tray in the Cabinet

2. Carefully slide the tray into the cabinet until the front mounting flanges on the
tray touch the vertical face of the cabinet (FIGURE 2-13).

40 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 2-13 Controller Tray Installed

The tray has mounting flanges on both sides with three mounting holes in them. The
top and bottom holes are large enough to fit over the heads of the screws already in
the cabinet rails used to mount the universal rails. If the tray was shipped with end
caps (bezels) clipped on the tray mounting flanges, remove them before sliding the
tray all the way in over the mounting screw heads.

To remove an end cap, place your thumb on the lower front face of the cap and reach
your forefinger underneath to the back bottom edge of the cap, then pull the cap
towards you and slightly upwards.

On the rear of the controller tray, a flat metal tab on each side corner slides into a
special mounting clip on the rear of each universal rail, securing the back of the tray.
This eliminates the need for rear mounting screws to secure the tray. For racks that
might move or be shipped, Sun recommends that you install M4 screws through the
hole in the tab and into the corresponding threaded hole in the rail as shown in
FIGURE 2-14.

Chapter 2 Installing Trays 41

 FIGURE 2-14 Rail Clip and Rear Mounting Hole on Rear of Tray

3. Insert a single 8-32 pan head screw through the center hole in each front
mounting flange and tighten (FIGURE 2-15).

42 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 2-15 Securing the Tray to the Front of a Sun Rack 900/1000 Cabinet

4. Replace the end caps (bezels) that cover the mounting flanges on the front of
the array tray.
On each front mounting flange, there is a small tab over which the end caps fit.
The end caps have a slot on top for this tab.

a. Place the end cap over the tab so the tab can go into the slot.

b. Snap the bottom of the end cap into place.

Chapter 2 Installing Trays 43

 Connecting the Power Cables
1. Verify that both power switches are turned off.

2. Verify that the circuit breakers in the cabinet are turned off.
3. Connect each power supply in the tray to a separate power source in the
cabinet.
4. Connect the primary power cables from the cabinet to the external power
source.

Note – Do not power on the storage array until you complete the procedures in this
chapter. The power-on sequence is described in detail in Chapter 7.

Inter-tray Cabling
This section describes how to cable a controller tray to the drive expansion trays for
several different configurations. Each controller has one expansion port (FIGURE 2-16).
Controller A controls drive channel 1 through the A-side modules; Controller B
controls drive channel 2 through the B-side modules. Each drive channel provides a
separate path for data transfer from the controller tray to the expansion trays; the
two channels provide redundancy.

FIGURE 2-16 Expansion Ports on the Controller Tray

SAS Expansion Ports to the Expansion Tray

Link Link Link Link Link Link Link Link

Link Link Link Link Link Link Link Link

1 DRIVE EXPANSION 1 DRIVE EXPANSION
HOST S HOST S
A A
S S S S
A
S
2 S
3 A
S
2 S
3
A
S
HOST A
S
HOST

Each expansion tray has two SAS port connectors, one marked with an up arrow
and the other marked with a down arrow (FIGURE 2-17). You use SAS cables to
connect drive expansion trays to the controllers in the controller tray.

44 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Note – Perform all SAS connections from an Out (down arrow) port to an In (up
arrow) port. If the cable is connected to two connectors with the same arrows,
communication between the two drive trays will be lost.

FIGURE 2-17 Expansion Ports on a Drive Expansion Tray

1 2 1 2

1. SAS Expansion In Port

2. SAS Expansion Out Port

Array Configuration Naming Convention

The configuration naming convention is “controller trays x trays” where the first
number is the controller tray and the second is the sum of the controller tray and the
number of drive expansion trays. For example, 1x1 is a standalone controller tray,
1x2 is the controller tray and one expansion tray, 1x3 is the controller tray and 2
expansion trays (TABLE 2-1).

TABLE 2-1 Controller Tray and Drive Expansion Tray Configurations

Configuration Identifier Controller Tray Number of Expansion Trays

1x1 1 0
1x2 1 1
1x3 1 2
1x4 1 3

Note – Do not add more expansion trays than the storage array supports.

Use the following instructions to connect the controller tray to one or more drive
expansion trays.

Chapter 2 Installing Trays 45

 Connecting Drive Expansion Trays
Keep the following points in mind when adding expansion trays to your storage
array:
■ Once the drive expansion tray is physically installed, the expansion trays should
be turned on and connected to the array with power on. The array must be at an
optimal status with I/O data transfer turned off. If you need to add an expansion
tray to a storage array that cannot be taken off-line, contact your Sun Technical
Support representative before attempting to connect the new tray.
■ Controller trays and expansion trays are shipped with protective plastic plugs in
the SAS expansion ports. You must remove these before connecting cables.
■ Expansion trays are added serially, in a chain (actually two chains: channel one
through the A-side controller and I/O modules, and channel two through the B-
side controller and I/O modules). The SAS cable from the expansion port on a
controller connects to the In port (Up arrow) on an expansion tray I/O module.
The SAS cable from an I/O module on expansion tray 1 to a corresponding I/O
module on expansion tray 2 connects from the Out port on expansion tray 1 to the
corresponding In port on expansion tray 2. This pattern repeats for each
additional drive expansion tray on a channel. See FIGURE 2-20 for an illustration of
this reverse cabling pattern.
■ To connect cables for maximum redundancy, controller B must be cabled to the
expansion tray B-side I/O modules in the opposite order as the expansion tray A-
side I/O modules. That means the last I/O module in the A-side chain from
controller A must be the first I/O module in the B-side chain from controller B. See
FIGURE 2-20 for an illustration of cabling for maximum tray level redundancy.
■ On all SAS cables, affix a label to each end of the cable. See “Tray Interconnect
Cable Labeling” on page 53 for labeling tips.

46 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Cabling an Expansion Tray to a Controller Tray
A Controller tray has two expansion ports, one on Controller A and one on
Controller B. To connect a drive expansion tray, connect an SAS cable from each
expansion port on the controller to each In port on the expansion tray. FIGURE 2-18
shows a 1x2 array configuration consisting of one controller tray and one drive
expansion tray. Two SAS cables are required.

FIGURE 2-18 1x2 Array Configuration Cabling Example

Expansion Tray

Controller Tray

A B

To cable a 1x2 array configuration:

1. Locate the Controller A and Controller B expansion ports at the back of the
controller tray (FIGURE 2-16).

2. Locate the In and Out expansion ports at the A-side and B-side back of the
expansion tray (FIGURE 2-17).

3. Connect one SAS cable between the Controller A expansion port and the A-
side In port on the expansion tray (FIGURE 2-18).

4. Connect one SAS cable between the Controller B expansion port and the B-side
In port on the expansion tray (FIGURE 2-18).

Chapter 2 Installing Trays 47

 Cabling an Expansion Tray to Another Expansion
Tray
Each additional expansion tray is added to the preceding expansion tray by
connecting SAS cables from the Out ports of the first tray to the In ports of the next
tray. FIGURE 2-19 illustrates a 1x3 storage array configuration consisting of one
controller tray and two expansion trays. The cable connections on the B-side are
reversed (the cable from the controller A expansion port goes to the In port of
expansion tray 1; the cable from the controller B expansion port goes to the In port
on expansion tray 2) for maximum redundancy. This pattern continues for each
additional tray you add. Two more SAS cables are required for each additional tray.

FIGURE 2-19 1x3 Storage Array Configuration Cabling

Expansion Tray 2

Expansion Tray 1

Controller Tray

A B

48 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
To cable a 1x3 array configuration for maximum redundancy:

1. Locate the Controller A and Controller B expansion ports at the back of the
controller tray (FIGURE 2-16).

2. Locate In and Out expansion ports at the A-side and B-side back of the
expansion tray (FIGURE 2-17).

3. Connect one SAS cable between the Controller A expansion port and the A-
side expansion In port of expansion tray 1 (FIGURE 2-19).

4. Connect one SAS cable between the Controller B expansion Out port and the B-
side expansion In port of expansion tray 2 (FIGURE 2-19).

5. Connect one SAS cable between the expansion tray 1 Out port and the A-side
expansion In port of expansion tray 2 (FIGURE 2-19).

6. Connect one SAS cable between the expansion tray 2 B-side Out port and the
B-side In port of expansion tray 1 (FIGURE 2-19).

Cabling a Third Drive Expansion Tray

Each additional expansion tray is added to the preceding expansion tray by
connecting two additional SAS cables from the Out ports of the preceding tray to the
In ports of the next tray in the loop. FIGURE 2-20 illustrates a 1x4 storage array
configuration consisting of one controller tray and three expansion trays.

The cable connections on the B-side are reversed (the cable from the controller A
expansion port goes to the In port of expansion tray 1; the cable from the controller
B expansion port goes to the In port on expansion tray 3) for maximum redundancy.

Chapter 2 Installing Trays 49

FIGURE 2-20 1x4 Storage Array Configuration Cabling

Expansion Tray 3

Expansion Tray 2

Expansion Tray 1

Controller Tray

A B

To cable a 1x4 array configuration for maximum redundancy:

1. Locate the Controller A and Controller B expansion ports at the back of the
controller tray (FIGURE 2-16).

2. Locate In and Out expansion ports at the A-side and B-side back of the
expansion tray (FIGURE 2-17).

3. Connect one SAS cable between the Controller A expansion port and the A-
side expansion In port of expansion tray 1 (FIGURE 2-20).

4. Connect one SAS cable between the Controller B expansion Out port and the B-
side expansion In port of expansion tray 3 (FIGURE 2-20).

5. Connect one SAS cable between the expansion tray 1 Out port and the A-side
expansion In port of expansion tray 2 (FIGURE 2-20).

50 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
6. Connect one SAS cable between the expansion tray 2 Out port and the A-side
expansion In port of expansion tray 3 (FIGURE 2-20).

7. Connect one SAS cable between the expansion tray 3 B-side Out port and the
B-side In port of expansion tray 2 (FIGURE 2-20).

8. Connect one SAS cable between the expansion tray 2 B-side Out port and the
B-side In port of expansion tray 1 (FIGURE 2-20).

Tray Interconnect Cable Labeling

Labels for the drive-side interface cables identify which controller ports and which
I/O module ports in an expansion tray you use when you attach cables between a
controller tray and the drive expansion tray. Cable labels are useful if you need to
disconnect cables to service a controller.

Attach a label to each end of the cable. Use this design to create labels for drive
cables:
■ Controller ID (for example, Controller A)
■ Drive expansion tray ID (for example, Tray A)
■ Expansion port ID (for example, In or Out)
■ I/O module ID

Example Label Abbreviation

In this example, the storage configuration has the following characteristics:
■ Drive channel 1
■ Controller A, drive channel 1
■ IO module 1
■ Expansion Tray A-Left Out port (left I/O module out port)

Using this design, the label includes the following information:

CtA-Dch1, Dm1-Tray_A (left), Out

Chapter 2 Installing Trays 51

 Single-Controller Configurations
This configuration has a single controller and a single back-end channel. By
definition, there is a single path connection to the data host, and no redundancy is
available. There can be drive expansion trays on the single back-end channel.

The cabling is the same as the cabling on a single channel of an ordinary array, such
as that shown on the A-side in FIGURE 2-18. CRU removal and replacement
procedures in a single-controller configuration are the same as those for a dual-
controller configuration with a failed controller (with the exception of the service
procedures targeted at the failed controller). These procedures are available in
Service Advisor. Maintenance procedures such as firmware updates or servicing of
the controller tray or drive expansion trays will cause loss of access to the storage
array during the performing of the procedure, since there is no backup channel.

Performance and default behavior are the same as a dual-controller configuration

with a failed or missing controller. Write cache is by nature in write-through mode
because there is no cache mirroring possible.

Next Steps
Now You Are Ready To Connect The Management Host, As Described In Chapter 3.

52 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Chapter 2 Installing Trays 53
54 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 3

Connecting the Management Host

This chapter describes Sun StorageTek 2500 Series Array cable connections for hosts.
It contains the following sections:
■ “Connecting the Management Host” on page 55

Connecting the Management Host

The management host directly manages Sun StorageTek 2500 Series Arrays over an
out-of-band network. This section describes how to setup an out-of-band connection
between the Ethernet port of a controller (FIGURE 3-1) and the management host.
FIGURE 3-1 Ethernet Ports for Controller A and Controller B

Controller A
Ethernet port

Ethernet port
Controller B

55
 Note – Before you begin, ensure that the two required Ethernet cables are available.
These requirements are outlined in the StorageTek 2500 Series Array Site Preparation
Guide.

There are three ways to establish a connection between the management host and
Ethernet port 1 of a controller module:
■ “Attaching the Ethernet Ports to the LAN of the Management Host” on page 56
■ “Attaching the Ethernet Ports to the Management Host Using an Ethernet Hub”
on page 56
■ “Attaching the Ethernet Ports Directly to the Management Host With a Cross-
Over Cable” on page 57

Attaching the Ethernet Ports to the LAN of the

Management Host
To attach the Ethernet ports to the local area network (LAN) of the management host:

1. Locate the Ethernet port for Controller A and Controller B at the back of the
controller tray (FIGURE 3-1).

2. Connect Ethernet cables to the Ethernet ports of each controller.

3. Connect the other end of each Ethernet cable to the LAN on which your
management host resides (preferably on the same subnet).

Attaching the Ethernet Ports to the Management

Host Using an Ethernet Hub
To attach the Ethernet ports and the management port Ethernet interface to an
Ethernet hub on a private subnet:

1. Locate Ethernet ports on Controller A and Controller B at the back of the

controller tray (FIGURE 3-1).

2. Connect Ethernet cables to the Ethernet ports of each controller module.

3. Connect the other end of each Ethernet cable to an Ethernet hub.

4. Connect an Ethernet port on the management host to the Ethernet hub.

56 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Attaching the Ethernet Ports Directly to the
Management Host With a Cross-Over Cable

Note – This method would typically be used only to establish temporary IP

connectivity between the management host and the controller’s Ethernet ports.

To attach the Ethernet ports directly to the management host using cross-over cables:

1. Locate the Ethernet ports for Controller A and Controller B at the back of the
controller tray (FIGURE 3-1).

2. Obtain and connect Ethernet cross-over cables to the Ethernet port of each
controller module.

3. Connect the other end of each Ethernet cable directly to your management host
Ethernet ports.

Next Steps
Now You Are Ready To Connect The Data Host To Your Array, As Described In
Chapters 4 to 6.

Chapter 3 Connecting the Management Host 57

58 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 4

Connecting Data Hosts to the 2510

Array

This chapter describes cabling data hosts to the Sun StorageTek 2510 Array using
iSCSI. It contains the following sections:
■ “Connecting Data Hosts to the 2510 Array” on page 59
■ “Next Steps” on page 62

Connecting Data Hosts to the 2510 Array

The Sun StorageTek 2510 Array is an Internet Small Computer System Interface
(iSCSI) system that communicates with hosts over an Ethernet data path.

The hosts that initiate data need a NIC as noted in “iSCSI Concepts” on page 98.

For initial iSCSI configuration information, go to Appendix C.

Note – For maximum hardware redundancy, each host must have a minimum of
two Ethernet NICs for dual paths. Dual-port NICs give you two paths into the
storage array, but do not ensure redundancy if the NIC fails. Single controller and
single path configurations are supported, but are not recommended.

As shown in FIGURE 4-1, each 2510 controller has two Ethernet host ports for data
path transmission with the hosts.

59
 FIGURE 4-1 Ethernet Host Ports on the Controllers

1. Not used
2. Ethernet Host Port

The most common topologies to connect from the host to the controllers are:
■ Direct topology – Connecting directly from the hosts to the controllers.
■ Network topology – Connecting from the hosts to the controllers through a
switch or other network components. Also called a fabric or switched topology.

Alternate topologies such as single-controller configurations and mixed

configurations are described in Appendix D.

FIGURE 4-2 Direct Topology – Two Hosts Connected to Each Controller

1. Hosts
2. NIC 1
3. NIC 2
4. Host Port 1
5. Host Port 2
6. Controller A
7. Controller B

60 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 FIGURE 4-3 Network Topology – Two Hosts Connected to the Controllers Through a
Switch

1. Hosts
2. NIC 1
3. NIC 2
4. Host Port 1
5. Host Port 2
6. Controller A
7. Controller B

▼ To Connect Host Cables

1. Insert one end of the Ethernet cable into a host port on the controller.

2. If direct topology, insert the other end of the Ethernet cable into the port on the
NIC on the data host.

3. If network topology, insert the other end of the Ethernet cable into a switch
port.

a. Connect a second cable from the switch to the port on the NIC.

4. Repeat steps 1 to 3 for each host-to-controller connection.

Relocation Cautions
Use the following guidelines when relocating trays or drives from one storage array
to another.

Chapter 4 Connecting Data Hosts to the 2510 Array 61

 Caution – Potential data loss – Moving a storage array or array components that are
configured as part of a volume group can result in data loss. To prevent data loss,
always consult a Customer Support representative before relocating configured
drives, controller trays, or drive expansion trays.

Do not move controller trays or drive expansion trays that are part of a volume
group configuration. If you must move array components, contact a Customer
Support representative for procedures. A Customer Support representative might
direct you to complete several tasks prior to undertaking the relocation. These tasks
might include:
■ Creating, saving, and printing an array profile of each storage array that is
affected by the relocation of a drive or tray.
■ Performing a complete backup of all data on the drives that you intend to move.
■ Verifying that the volume group and each of its associated volumes on the
affected storage array have an Optimal status.
■ Determining the location and status of any global hot spares associated with the
affected storage array.

Next Steps
After You Connect The Management And Data Hosts, You Can Power On The Trays,
As Described In Chapter 7.

62 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 5

Connecting Data Hosts to the 2530

Array

This chapter describes Sun StorageTek 2500 Series Array cable connections for hosts.
It contains the following sections:
■ “Connecting Data Hosts to the 2530 Array” on page 63
■ “Next Steps” on page 67

Connecting Data Hosts to the 2530 Array

Data transmission between the host and the controllers in the array module is
through Serial Attached SCSI (SAS) cables. All connections from the host to the
controllers are direct connections. FIGURE 5-1 shows an example of a direct host
connection from a single data host with dual HBAs.

63
 FIGURE 5-1 Direct Connection From a Single Host With Dual HBAs

1. Host
2. HBA 1
3. HBA 2
4. Host Connectors on the
Controllers
5. Controller A
6. Controller B

FIGURE 5-2 shows an example of direct host connections from two data hosts, each
with dual HBAs.

FIGURE 5-2 Direct Connections from Two Data Hosts with Dual HBAs.

FIGURE 5-3 shows an example of direct host connections from three data hosts, each
with dual HBAs.

64 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 5-3 Direct Connections from Three Data Hosts with Dual HBAs

Note – For maximum hardware redundancy, you must install a minimum of two
HBAs in each host. Dual-port HBAs give you two paths into the storage array but do
not ensure redundancy if the HBA fails.

Before you connect data hosts directly to the array, check that the following
prerequisites have been met:
■ Interface cables are connected and between the HBAs and the array controllers.
■ SAS cables (1-, 3-, or 6-meters) are available to connect the controller’s host ports
to the data host HBAs.

Each controller module on a controller tray has three SAS host ports (FIGURE 5-4).

Chapter 5 Connecting Data Hosts to the 2530 Array 65

 FIGURE 5-4 SAS Data Host Ports (on Back of Tray)

1 2 3 1 2 3

Link Link Link Link Link Link Link Link

Link Link Link Link Link Link Link Link

1 DRIVE EXPANSION 1 DRIVE EXPANSION
HOST S HOST S
A A
S S S S
A
S
2 S
3 A
S
2 S
3
A
S
HOST A
S
HOST

1. SAS Host Port 1

2. SAS Host Port 2
Controller A Controller B
3. SAS Host Port 3

▼ To Connect Data Hosts to a 2530 Array

1. Locate the host ports at the back of the controller tray (FIGURE 5-4).

2. Connect one end of the SAS cable to a host port on a controller module.
Host ports are numbered from left to right: host port 1, host port 2, and host
port 3.
3. Connect the other end of each SAS cable to a data host HBA.

4. Repeat these steps for each host-to-controller connection.

Relocation Cautions
Use the following guidelines when relocating trays or drives from one storage array
to another.

Caution – Potential data loss – Moving a storage array or array components that are
configured as part of a volume group can result in data loss. To prevent data loss,
always consult a Customer Support representative before relocating configured
drives, controller trays, or drive expansion trays.

66 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Do not move controller trays or drive expansion trays that are part of a volume
group configuration. If you must move array components, contact a Customer
Support representative for procedures. A Customer Support representative might
direct you to complete several tasks prior to undertaking the relocation. These tasks
might include:
■ Creating, saving, and printing an array profile of each storage array that is
affected by the relocation of a drive or tray.
■ Performing a complete backup of all data on the drives that you intend to move.
■ Verifying that the volume group and each of its associated volumes on the
affected storage array have an Optimal status.
■ Determining the location and status of any global hot spares associated with the
affected storage array.

Next Steps
After You Connected The Management And Data Hosts, You Can Power On The
Trays, As Described In Chapter 7.

Chapter 5 Connecting Data Hosts to the 2530 Array 67

68 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 6

Connecting Data Hosts to the 2540

Array

This chapter describes Sun StorageTek 2500 Series Array cable connections for hosts.
It contains the following sections:
■ “Connecting Data Hosts to the 2540 Array” on page 69
■ “Next Steps” on page 75

Connecting Data Hosts to the 2540 Array

The Sun StorageTek 2540 Array connects to data hosts through Fibre Channel (FC)
cables.

Note – For maximum hardware redundancy, you must install a minimum of two
HBAs in each host. Dual-port HBAs give you two paths into the storage array but do
not ensure redundancy if the HBA fails. Single controller and single path
configurations are supported but are not recommended.

69
 2540 Array Data Host Connection Topologies
You can connect data hosts to access the Sun StorageTek 2540 Array directly to the
array, or through Fibre Channel (FC) switches to the array. The following figures
illustrate four possible host connection topologies for the 2540 Array:
■ Direct connection from a single data host server (FIGURE 6-1)
■ Direct connection from two data host servers (FIGURE 6-2)
■ Data host connection through Fiber Channel switch fabric (FIGURE 6-3)
■ Mixed connection, direct and through switch (FIGURE 6-4)

FIGURE 6-1 Direct Connection from a Single Data Host Server

1. Host
2. HBA 1
3. HBA 2
4. Host Port
5. Controller A
6. Controller B

70 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
FIGURE 6-2 Direct Connection from Two Data Host Servers

1. Host
2. HBA 1
3. HBA 2
4. Host Port 1
5. Host Port 2
6. Controller A
7. Controller B

FIGURE 6-3 Data Host Connection Through a Fibre Channel Switch

Chapter 6 Connecting Data Hosts to the 2540 Array 71

 FIGURE 6-4 Mixed Topology of Data Hosts Connected Directly and Through FC Switches

1. Host
2. HBA 1
3. HBA 2
4. Host Port 1
5. Host Port 2
6. Controller A
7. Controller B

FIGURE 6-5 Connecting the SFP and Fiber-optic Cable to a 2540 Controller

1. Fibre Channel Host Port

2. SFP is Inserted
into the Host Port
3. Fiber-optic Cable is
inserted into the SFP

72 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 1. Host 1
2. HBA 1
3. HBA 2
4. Host 2
5. Host 3
6. Host Port 1
7. Host Port 2
8. Controller A
9. Controller B

2540 Array Data Host Connections

Data transmission from the host to the array controller modules is through fiber-
optic cables. The fiber-optic cables connect to the controllers through Small Form-
factor Pluggable (SFP) transceivers (FIGURE 6-5).

The Sun StorageTek 2540 Array controller tray has four FC host ports, two per
controller module. To maintain redundancy, connect two data paths from each host,
one to each controller.

FIGURE 6-6 FC host Connectors on the 2540 Controller

1. not used
2. Fibre Channel data
2 2 host port 1
1 3 1 3
3. Fibre Channel data
host port 2

Chapter 6 Connecting Data Hosts to the 2540 Array 73

 ▼ To Connect Data Hosts Using Fibre Channel
1. Locate the host ports at the back of the controller tray (FIGURE 6-6).

2. Plug one SFP transceiver into a host port.

3. Plug one end of the fiber-optic cable into the SFP transceiver.

4. Plug the other end of the fiber-optic cable into one of the HBAs in the
host (direct topology) or into a switch (fabric topology).

5. Repeat these steps for each host-to-controller connection.

Relocation Cautions
Use the following guidelines when relocating trays or drives from one storage array
to another.

Caution – Potential data loss – Moving a storage array or array components that are
configured as part of a volume group can result in data loss. To prevent data loss,
always consult a Customer Support representative before relocating configured
drives, controller trays, or drive expansion trays.

Do not move controller trays or drive expansion trays that are part of a volume
group configuration. If you must move array components, contact a Customer
Support representative for procedures. A Customer Support representative might
direct you to complete several tasks prior to undertaking the relocation. These tasks
might include:
■ Creating, saving, and printing an array profile of each storage array that is
affected by the relocation of a drive or tray.
■ Performing a complete backup of all data on the drives that you intend to move.
■ Verifying that the volume group and each of its associated volumes on the
affected storage array have an Optimal status.
■ Determining the location and status of any global hot spares associated with the
affected storage array.

74 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Next Steps
After You Connected The Management And Data Hosts, You Can Power On The
Trays, As Described In Chapter 7.

Chapter 6 Connecting Data Hosts to the 2540 Array 75

76 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 7

Powering On the Array

This chapter describes initial tray power-on procedures in the following sections:
■ “Before Powering On” on page 77
■ “Powering On the Storage Array” on page 78
■ “Powering Off the Array” on page 79
■ “Next Steps” on page 80

Before Powering On
You should decide on a IP address method before powering on. The controllers will
obtain IP addresses from DHCP if it is available on the network. If DHCP is not
available, the controller tray defaults to internal static IP addresses. (See the Sun
StorageTek Common Array Manager Software Installation Guide for information about
configuring IP addresses on controller modules.)

For instructions on configuring IP addresses on the controllers using the serial

interface, see “Configuring the IP Address of the Controller Modules” on page 89.
For an example of how to set up the DHCP server, see “Configuring a DHCP Server”
on page 133.

77
 Powering On the Storage Array
Use this procedure to turn power on for all trays installed in the cabinet (FIGURE 7-1).

Note – The order in which you power up the trays is important. Be sure to power
on the controller tray last in order to ensure that the disks in the drive expansion
trays have enough time to spin completely before being scanned by the controllers in
the controller tray.

FIGURE 7-1 Tray Power Connectors and Switches

Controller A Controller B 2
1
1. Controller A power switch
2. Controller B power switch

1. Prepare the power cables as specified in “Connecting the Power Cables” on

page 46.

2. Turn on the cabinet circuit breakers, if applicable.

3. Press the power switches at the back of each expansion tray to the On position.
While the tray powers on, the green and amber LEDs on the front and back of the
controller tray turn on and off intermittently. Depending on your configuration, it
can take several minutes for the tray to power on. When the power-on sequence is
complete, the LEDs are steady green.
Wait until all the disk drive indicator lights on the expansion trays are steady
green before proceeding to the next step.

4. Press each power switch at the back of the controller tray to the On position.

5. Check the status of each tray.

After the power-on sequence is complete, confirm the following:
■ The green OK/Power LEDs on each drive in the tray are steady on.

78 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
■ The green OK/Power LED on the tray is steady on.
If all tray and drive OK/Power LEDs are steady green and the amber Service
Required LEDs are off, the power-on sequence is complete and no faults have
been detected.

Powering Off the Array

The array rarely needs to be powered off. You remove power only when you plan to
physically move the storage array to another location or are adding additional trays
to a controller tray.

To power off the storage array, do the following:

1. Stop all I/O from the hosts, if connected, to the storage array.

2. Wait approximately 2 minutes until all disk drive LEDs have stopped flashing.

Note – If Disk Scrubbing is enabled, the disk drive LEDs will continue to flash after
the 2-minute period has elapsed. By waiting the 2-minute period, you ensure that
the data residing in cache has been written to disk. The LED flash rate during disk
scrubbing (slow, periodic blink) is different from the flash rate of I/O (fast, random).

After the 2-minute period, data residing in cache is written to disk and the battery
mechanisms are disengaged.

3. Check the Cache Active LED on the controller (FIGURE 1-11) to determine if any
outstanding cache needs to be written.
If the LED is on, there is still data that needs to be flushed and written to disk.

4. Ensure that the Cache Active LED is no longer flashing before powering off the
storage array.

5. Press each power switch at the back of the controller tray to the Off position.

6. Press the power switches at the back of each drive expansion tray to the Off
position.

Chapter 7 Powering On the Array 79

 Next Steps
After you have connected the management host and data hosts, you are ready to
install the management host software as described in the Sun StorageTek Common
Array Manager Software Installation Guide and the data host software as described in
Chapter 8. For iSCSI, proceed to Appendix A.

80 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 8

Data Host HBAs and Software for

the 2540 and 2530 Arrays

This chapter describes how to install data host software, HBAs, and other software
on different host platforms. It contains the following sections:
■ “Data Host Software” on page 81
■ “Setting Up a Data Host On a Solaris System” on page 82
■ “Installing Data Host Software for Operating Systems Other Than Solaris” on
page 85
■ “Enabling Solaris Multipathing Software” on page 86
■ “Next Steps” on page 88

Data Host Software

The data host software contains tools that manage the data path I/O connections
between the data host and the storage array. This includes drivers and utilities that
enable storage management hosts to connect to, monitor, and transfer data in a
storage area network (SAN).

Note – Some management hosts can also be used as data hosts.

For information on configuring iSCSI and data hosts, refer to “Configuring iSCSI on
the Sun StorageTek 2510 Array” on page 97.

81
 HBAs and Drivers
A Host Bus Adapter (HBA) enables communications between the host and the
controller tray (or other devices in-between). It also manages all data I/O on your
data host. The specific HBAs you need depend on the host server platform,
operating system, data transport (SAS, FC, or iSCSI) aka host interface, and data
transfer rates used in your storage area network. HBAs must be ordered separately,
from Sun or their respective manufacturers. Sun HBAs can be ordered from:

http://www.sun.com/storagetek/networking/

The required versions of HBA drivers must be installed on the data host before you
can set up a data host. The Sun StorageTek 2500 Series Array Release Notes lists the
data host requirements for HBAs and drivers. Get the release notes at:

http://doc.sun.com/app/docs/prod/st2500.array#hic

Refer to the specific vendor HBA documentation for instructions on installing HBA
drivers.

Multipathing
Data host software controls the data path between the data host and the storage
array. If there is more than one path between the host and the storage array for
redundancy, this function is called multipathing.

Install data host software (including multipathing) on each data host that
communicates with the Sun StorageTek 2500 Series Array. The multipathing
software you need depends on the host platform, HBA, and the data transport (SAS,
FC, or iSCSI) in your storage area network. This information is listed in the latest
version of the Sun StorageTek 2500 Series Array Release Notes.

Setting Up a Data Host On a Solaris

System
The Sun StorageTek 2500 Series Array provides data path support for data hosts
running Solaris, Windows 2000, Windows Server 2003, Red Hat Linux, HP-UX, and
IBM AIX operating systems. This section applies to hosts running Solaris 9 and 10.

See the Sun StorageTek 2500 Series Array Release Notes for the latest supported
operating system versions.

82 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 Note – To install data host software on systems that are not running the Solaris OS, see
“Installing Data Host Software for Operating Systems Other Than Solaris” on
page 85.

Multipathing is included in the Solaris 10 OS. For Solaris 9 data hosts, you need the
SAN Foundation Kit software (which includes the multipathing software).
To install data host software on Solaris OSs, see the following sections:
■ “To Obtain Sun Solaris 9 Data Host Software” on page 83
■ “To Install the SAN 4.4 Data Host Software” on page 84

▼ To Obtain Sun Solaris 9 Data Host Software

Obtain Sun Solaris 9 data host software:

1. Go to the Sun Microsystems web page (sun.com).

The Sun home page is displayed.

2. Select Downloads from the home page navigation bar.

The Downloads page is displayed (it is not labeled).

3. On the View by Category tab, select System Administration >> Storage

Management.
The Storage Management page is displayed, showing a list of downloadable
storage-related products.

4. Select the SAN 4.4 product.

The login page is displayed.

5. Login using your Sun account ID.

The SAN 4.4.x Download page is displayed.

6. Accept the License Agreement and select the SAN 4.4 version required for your
operating system.
The data host software version you need depends on your operating system. See
the Sun StorageTek 2500 Series Array Release Notes for the current data host
software requirements. Download the Solaris x (9) Base Package (if you do not
already have it installed), and then the Install_it Script SAN 4.4.x version as
recommended in the release notes.
There is a README file available on the SAN 4.4.x Download page with
instructions for unpacking and installing the download file on your data host
computer.

Chapter 8 Data Host HBAs and Software for the 2540 and 2530 Arrays 83
 ▼ To Install the SAN 4.4 Data Host Software
To launch the host software installer:

1. Log in to the host as root.

2. Change to the SAN_4.4.xx_install_it directory in which the compressed

installation file was unpacked:
cd <user-specified location>/SAN_4.4.xx_install_it

3. where xx is the software version number of the installed files. Start the host
software installer by typing the following command:
./install_it
When the installation is complete, the root prompt returns.

Note – It might be required that the host be rebooted into single user, and then
rebooted right afterward to multiuser.

4. Enable the Sun StorageTek Traffic Manager multipathing software (see

“Enabling Solaris Multipathing Software” on page 86).

▼ To Obtain Software for Operating Systems Other

Than Solaris
1. Go to the Sun Microsystems web page (sun.com).
The Sun home page is displayed.

2. Select Downloads from the home page navigation bar.

The Downloads page is displayed.

3. On the View by Category tab, scroll down to select System Administration >>
Storage Management.
The Storage Management page is displayed, showing a list of downloadable
storage-related products.

4. Scroll down and select the StorageTek 2500 Series multipath/failover option for
your particular operating system.
The login page is displayed.

5. Login using your Sun account ID.

The product Download page is displayed.

84 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
6. Accept the License Agreement and select the software version required for your
operating system.
The data host software version you need depends on your operating system. See
the Sun StorageTek 2500 Series Array Release Notes for the current data host
software requirements.
There is a README file available on the download page with instructions for
unpacking and installing the download file on your data host computer.

Installing Data Host Software for

Operating Systems Other Than Solaris
To install data host software for operating systems other than Solaris, see the
following sections:
■ “About Data Host Software For Non-Solaris Platforms” on page 85
■ “Downloading and Installing Sun RDAC Software” on page 86

Note – To download software from the Sun Download Center, you must register as
a Sun customer. The first time you click Download to download a software product,
click the Register Now link on the Login page, complete the required fields, and
click Register.

About Data Host Software For Non-Solaris

Platforms
The data host software for Red Hat Linux, HP-UX, AIX, and Windows platforms is
Sun Redundant Dual Array Controller (RDAC), also known as MPP, and is available
from the Sun Download Center (SDLC).
See the Sun StorageTek 2500 Series Array Release Notes for a list of supported operating
systems, patches, and HBAs.

Chapter 8 Data Host HBAs and Software for the 2540 and 2530 Arrays 85
 Downloading and Installing Sun RDAC Software
1. To download the latest version of Sun RDAC software (support for Windows
and Linux multipathing), go to:
http://www.sun.com/download/index.jsp
and select Hardware Drivers >> Storage.

2. Select the link for the RDAC driver for the Operating System you have.
An RDAC Driver download page is displayed.

3. Click Download.

4. Log in using your SDLC user name and password.

5. Read and accept the license agreement.

6. Select the link for the data host platform that you want to install.

7. Save the install package to a temporary directory.

8. Uncompress and untar the install package.

9. When the download is finished, log out of the SDLC.

A readme file is provided as part of the installation package. To install the software,
refer to the readme file for platform-specific instructions.

Enabling Solaris Multipathing Software

Sun StorageTek SAN Foundation software includes the Sun StorageTek Traffic
Manager multipathing software.

The procedure you use to enable multipathing software depends on the version of
Solaris OS running on the host:
■ “Enabling Multipathing Software for Solaris 9 OS” on page 87
■ “Enabling Multipathing Software for Solaris 10 OS” on page 87

For information on configuring iSCSI, refer to:

“Configuring iSCSI on the Sun StorageTek 2510 Array” on page 97.

86 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
▼ Enabling Multipathing Software for Solaris 9 OS
To enable the multipathing software on hosts running Solaris OS 9:

1. Open the /kernel/drv/scsi_vhci.conf file with a text editor.

2. Set mpxio-disable=”no”; in the file.

3. Set load-balance=”round-robin”; in the file.

4. Set auto-failback=”enable”; in the file.

5. Save the updated file.

6. Reboot the host.

7. Use the cfgadm command to configure HBA paths.

How you configure paths depends on how you are using your storage arrays in a
SAN or direct-attach environment.

See the Sun StorEdge SAN Foundation Software 4.4 Configuration Guide at:

http://www.sun.com/products-n-solutions/hardware/docs
/Network_Storage_Solutions/SAN/san_software/

for information about configuring paths.

▼ Enabling Multipathing Software for Solaris 10

OS
To enable multipathing software for all Fibre Channel (FC) ports on hosts running
Solaris OS 10:

1. Type the following command:

# stmsboot -e

Note – See the stmsboot(1M) man page for complete details.

You are prompted to confirm the command:

WARNING: This operation will require a reboot.
Do you want to continue? [y/n] (default: y)

2. Press Return to reboot the host.

Chapter 8 Data Host HBAs and Software for the 2540 and 2530 Arrays 87
 Next Steps
After you have installed and enabled multipathing on the data hosts, configure IP
addressing on the controller modules as described in Chapter 9.

88 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER 9

Configuring IP Addressing

In order for there to be an out-of-band Ethernet connection between the local

management host and the controller modules, the management host and the
controllers must have valid IP addresses.

This chapter describes how to configure IP addressing on the local management host
and on the controller modules. It contains the following sections:
■ “About IP Addressing” on page 89
■ “Configuring the IP Address of the Controller Modules” on page 89

About IP Addressing
The Sun StorageTek 2500 Series Array is managed out-of-band by way of a standard
Ethernet connection between the controller modules and your management host.

Perform the following procedures to ensure that the local management host and the
controllers have valid IP addresses:
■ Configure IP addresses for the controller modules (see “Configuring the IP
Address of the Controller Modules” on page 89)
■ Configure an IP address for the management host (see the Sun StorageTek Common
Array Manager Software Installation Guide)

Configuring the IP Address of the

Controller Modules
You can configure two types of IP addressing for the Ethernet port of each controller:

89
 ■ Dynamic Host Configuration Protocol (DHCP) IP addressing – IP addresses for
the Ethernet port are assigned dynamically from a DHCP server running
bootstrap protocol (BOOTP) services. An IP address assigned to an Ethernet port
is held only as long as needed. By default, DHCP is enabled at initial power-on.
■ Static IP Addressing – You assign a specific IP address to the Ethernet port of each
controller. Static IP addresses remain in effect until you modify or remove them or
you change the method of IP addressing for the Ethernet port to DHCP.
By default, if the controllers cannot find a DHCP server upon initial power-on, an
internal IP address is assigned to Ethernet port 1 of each controller:
■ The Ethernet port of Controller A is assigned IP address 192.168.128.101
■ The Ethernet port of Controller B is assigned IP address 192.168.128.102
■ The default subnet mask for each port is 255.255.255.0

To configure the Ethernet port on a controller with either dynamic or static IP

addressing, see one of the following sections:
■ “Configuring Dynamic (DHCP) IP Addressing” on page 90
■ “Configuring Static IP Addressing” on page 91

Configuring Dynamic (DHCP) IP Addressing

If BOOTP services are available on the DHCP server at initial power on of the
storage array, this server assigns a dynamic IP address for the Ethernet port on each
controller.
If a DHCP server is not available, the controller tray defaults to internal static IP
addresses as described in “Configuring the IP Address of the Controller Modules”
on page 89.
If you want to set up a DHCP server, refer to Appendix F for a description of how to
configure BOOTP services in Sun Solaris or Microsoft Windows environments.
You can restore DHCP IP addressing to Ethernet port 1 of either controller in either
of three ways:
■ Start a DHCP server on the same subnet, then reboot the 2500 Series Array.
■ Using the serial port interface (see “Using the Serial Port Interface to Assign IP
Addresses” on page 91).
■ Using the Sun StorageTek Common Array Manager (see the Sun StorageTek
Common Array Manager Software Installation Guide).

90 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 Configuring Static IP Addressing
There are two methods of assigning static IP addresses to the Ethernet ports of a
controller:
■ The serial port interface (see “Using the Serial Port Interface to Assign IP
Addresses” on page 91)
■ The Common Array Manager (see the Sun StorageTek Common Array Manager
Software Installation Guide).

Using the Serial Port Interface to Assign IP Addresses

You can use the serial port interface on a controller to set the IP address for the
Ethernet port on the controller.

To use the serial port interface to configure IP addressing for the Ethernet port of
each controller, you must complete the tasks described in the following sections:
■ “To Connect a Terminal to the Serial Port” on page 91
■ “To Set Up the Terminal Emulation Program” on page 92
■ “To Establish a Connection With the Serial Port” on page 92
■ “To Configure the IP Addresses” on page 94

▼ To Connect a Terminal to the Serial Port

You will establish a serial connection to each controller, Controller A and Controller
B. One mini-DIN to RJ45 serial port cables are supplied with each controller tray.

To connect a terminal to the serial port of a controller:

1. Connect the 6-pin mini-DIN connector of the serial cable to the serial port on
the controller (FIGURE 1-4 on page 8).

2. Connect the RJ-45 connector of the serial cable to the serial port on the
terminal. It may be necessary to use the RJ45-DB9 adapter between the serial
cable RJ-45 connector and the serial port of the terminal.

3. For PC and laptop serial connections, you will also need to use a null modem.
Connect the RJ45-DB9 null modem adapter between the serial cable RJ-45
connector and the PC serial port.

Note – If your PC does not have a serial port, you can use a USB–Serial Port adapter
(separately available from third-party vendors; not included with 2500 Series Array
ship kits).

Chapter 9 Configuring IP Addressing 91

 Serial Cable Pinouts
TABLE 9-1 shows the pinouts for the RJ45-DIN serial cable (Sun part number 530-
3544) included with the 2500 Series Array ship kit.

TABLE 9-1 RJ45 to DIN Serial Cable Pinouts

RJ45 ----------> PS2-miniDin

1 Tx 6 Rx
2
3 Rx 1 Rx
4,5,7 3, 5 GRD
6 Rx 2 Tx
8 4

▼ To Set Up the Terminal Emulation Program

To set up a terminal emulation program to connect to the serial port:

1. Select VT100 emulation.

2. Remove any modem strings from the connection profile.

3. Set up the connection profile with the following communication settings:

■ Data Rate: 38400
■ Data Bits: 8
■ Parity: None
■ Stop Bits: 1
■ Flow Control: None

▼ To Establish a Connection With the Serial Port

To establish a connection with the serial port and display the Service Interface menu:

1. Send a Break. Repeat until text appears.

92 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Note – The storage array serial port requires that the break character be received.
Use the appropriate escape sequence for your terminal setup to send the required
break character to the controller, For example, you generate the Break character on
some terminals by pressing the Control and Break keys simultaneously.

The serial port responds with a request to synchronize with the baud rate of the
terminal:
Set baud rate: press <space> within 5 seconds

2. Press the space bar within five seconds.

The serial port confirms the established baud rate for the connection:
Baud rate set to 38400

3. Press Break (see Note above)

The serial port responds with the following message:
Press within 5 seconds: <S> for Service Interface, <BREAK>
for baud rate
4. Press S to access the Service Interface menu.

Note – Send Break to synchronize the serial port to a different terminal port rate
(see Note above).

The serial port requests the serial port password:

Enter Password to access Service Interface (60 sec timeout):
->

5. Type the serial port password, kra16wen, and press Enter.

The Service Interface menu is displayed.

Service Interface Main Menu

==============================
1) Display IP Configuration
2) Change IP Configuration
3) Reset Storage Array (SYMbol) Password
Q) Quit Menu

Enter Selection:

Chapter 9 Configuring IP Addressing 93

 ▼ To Configure the IP Addresses
The serial port Service Interface menu enables you to set up the IP address
configuration for the Ethernet port on the controller.

To set up the IP address configuration for the Ethernet port on each controller:

1. Select option 2, Change IP Configuration:

Service Interface Main Menu

==============================
1) Display IP Configuration
2) Change IP Configuration
3) Reset Storage Array (SYMbol) Password
Q) Quit Menu

Enter Selection: 2

2. Specify that you do not want dynamic IP addressing, using a DHCP server,
used for this port:

Configure using DHCP? (Y/N): n

The current or default IP configuration for the selected Ethernet port is displayed.

3. Enter the static IP address and, optionally, a subnet mask for the Ethernet port:

Note – If you are not using DHCP IP addressing and have a gateway IP address on
your subnet, you must also specify a gateway IP address for the Ethernet port. This
option displays only if the serial interface detects a gateway.

Press '.' to clear the field;

Press '-' to return to the previous field;
Press <ENTER> and then ^D to quit (Keep Changes)

Current Configuration New Configuration

IP Address if1 : 192.168.128.101 IP-address
Subnet Mask if1 : 255.255.255.0 <ENTER>
Gateway IP Address if1: <ENTER>

4. When prompted, confirm the specified IP addressing.

The Service Interface menu is redisplayed.

94 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
5. Select option 1, Display IP Configuration, to confirm the IP address changes.

Service Interface Main Menu

==============================
1) Display IP Configuration
2) Change IP Configuration
3) Reset Storage Array (SYMbol) Password
Q) Quit Menu

Enter Selection: 1

The IP address configuration of the Ethernet port is displayed, and the Service
Interface menu displays again.

6. Press Q to quit the Service Interface menu.

7. Switch the serial cable to the serial port on the other controller and repeat these
steps to set the IP address on that controller as well.

8. Power cycle the controllers off and on again to reset them with the new IP
address.

When you have completed the IP address configuration for the Ethernet port on
both controllers and power cycled them, see the Sun StorageTek Common Array
Manager Software Installation Guide for instructions on registering and configuring the
storage array.

Chapter 9 Configuring IP Addressing 95

96 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
APPENDIX A

Configuring iSCSI on the Sun

StorageTek 2510 Array

This appendix describes initial configuration of iSCSI on the Sun StorageTek 2510
Array. It contains the following sections:
■ “Configuring iSCSI Overview” on page 97
■ “iSCSI Concepts” on page 98
■ “Configuring iSCSI - Detailed” on page 99
■ “Preparing for iSCSI and Installing Hardware” on page 99
■ “Configuring iSCSI Tasks” on page 100
■ “Configuring Other iSCSI Features” on page 104

Configuring iSCSI Overview

The following overview lists the major steps to configure the data host and target
storage after setting up the array and installing the management software.

For the full procedure go to “Configuring iSCSI - Detailed” on page 99

1. Configure an iSCSI port for each controller on the storage array.

2. On the data host:

a. Note its iSCSI Qualified Name (IQN) of the host.

b. Configure static discovery of the target ports.

3. In the Sun StorageTek Common Array Manager software:

a. Configure an initiator with the data host IQN.

97
 b. Create a volume

c. Map the volume to the initiator through the host or host group.

4. On the data host:

a. Link the initiator and target volume, if needed.

b. Verify that you see the created volume.

5. Use system administration commands in the OS to mount/read/write to the

volume.

iSCSI Concepts
Configuring iSCSI requires an understanding of the following concepts.
■ iSCSI target - a storage device accessed over an Ethernet connection while still
using the SCSI infrastructure. One iSCSI target is supported per array. The Target
Details page appears in the software when supporting a Sun StorageTek 2510
array.
■ iSCSI session - consists of up to four connections between an iSCSI initiator and
the iSCSI target. The iSCSI initiator and target send and receive data over an
Ethernet connection while still using the SCSI protocol. Across all connections
within a session, an initiator sees one and the same target. Multiple initiators may
be connected to the iSCSI Target.
■ Authentication - Communication between the initiator and the target array can be
protected using CHAP authentication.
■ iSCSI ports - used for communication between the iSCSI initiator and the iSCSI
target. The storage array supports two iSCSI ports per controller, for a total of
four iSCSI ports per array.
■ Ethernet Network Interface Card (NIC) - you connect an Ethernet data path from
the data host to the storage using a NIC on the host side.
A NIC is an input/output (I/O) adapter that connects a host to a computer
network. The host central processing unit (CPU) must process the Small
Computer System Interface (SCSI) information in Ethernet frames.
Ethernet NICs require a software initiator. The iSCSI initiator runs on the data
host and converts SCSI commands into iSCSI commands to send and receive data
over the Ethernet connection to a target storage system. iSCSI initiators are
operating system specific. Examples are provided for configuring initiators in
Solaris and Windows. Consult your operating system documentation for Linux.

98 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Configuring iSCSI - Detailed
The following sections detail the steps in planning, cabling, and configuring iSCSI:
■ “Preparing for iSCSI and Installing Hardware” on page 99
■ “Configuring iSCSI Tasks” on page 100
■ “Configuring Other iSCSI Features” on page 104

The first two sections contain tables listing each step in configuring iSCSI:
■ “iSCSI Preparation and Hardware Steps” on page 100
■ “iSCSI Configuration Steps” on page 101

You can use the procedures in conjunction with examples for Solaris and Windows.

For an example of configuring iSCSI on a Solaris host, go to “iSCSI Configuration

Example Using Solaris” on page 107.

For an example of configuring iSCSI on a Windows host, go to “iSCSI Configuration

Example Using Windows” on page 111.

For an example of configuring iSCSI on a Linux host, consult your Linux OS

documentation.

The RDAC driver for LINUX supports the Sun StorageTek 2510 Array. To download:

1. Go to www.sun.com

2. Select Download

3. Select View by Category

4. Select Systems Administration >> Storage Management, and scroll down to the
StorageTek 2500 Series offerings.

Preparing for iSCSI and Installing

Hardware
This section details the steps to prepare for iSCSI and complete the hardware
installation before beginning configuration.

Appendix A Configuring iSCSI on the Sun StorageTek 2510 Array 99

TABLE A-1 iSCSI Preparation and Hardware Steps

Step For more Information, refer to:

1. Identify the required OS, iSCSI software packages, OS documentation.

and patches. Sun StorageTek 2500 Series Array Release Notes, 6.1 or
higher. Download from
http://docs.sun.com/app/docs/coll/st2500arrays
2. Select a topology and if a network topology, “Connecting Data Hosts to the 2510 Array” on
provide a suitable Ethernet network. page 59
3. Set up the storage array, trays, cabling, and “Installing Trays” on page 27
networking, as noted in earlier chapters. “Connecting the Management Host” on page 55
. “Connecting Data Hosts to the 2510 Array” on
page 59
4. Power on the storage array. “Powering On the Array” on page 77
5. If needed, change the array management default IP “Configuring IP Addressing” on page 89
addresses using the serial port interface.
6. Install the Sun StorageTek Common Array Manager Refer to Sun StorageTek Common Array Manager
software. Software Installation Guide
7. In the software, register the storage array and (sent with the controller tray).
perform the basic administration setup.
Note: for storage array configuration, use the iSCSi
steps that follow.

Configuring iSCSI Tasks

This section describes the steps to configure iSCSI on the data host and in the
Common Array Manager software. It contains the following sections:
■ TABLE A-2,“iSCSI Configuration Steps” on page 101
■ “Identifying the Target Port IP Address” on page 101
■ “Adding Initiator Information” on page 103
■ “Additional iSCSI Topics in the Online Help” on page 104
■ “Configuring Mutual Authentication for an iSCSI Session” on page 105

For an example of configuring iSCSI on a Solaris host, go to “iSCSI Configuration

Example Using Solaris” on page 107.

For an example of configuring iSCSI on a Windows host, go to “iSCSI Configuration

Example Using Windows” on page 111.

100 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 .

TABLE A-2 iSCSI Configuration Steps

Step For more Information, refer to:

1. In the Common Array Manager software: “Identifying the Target Port IP

A. Go to the Ports Summary page. Address” on page 101
B. Verify that the target ports (minimum one for each controller) are up.
C. Note the target IP addresses and ports.
D. Change the port IP addresses from the default, if needed, on the Port
Detail page.
2. On the data host: OS Documentation
A. Note the iSCSI Qualified Name (IQN) of the initiator on the data host. “iSCSI Configuration Example
B. Set the discovery method of the target as static. Using Solaris” on page 107
C. Discover the target ports (minimum one for each controller) from the “iSCSI Configuration Example
initiator. Using Windows” on page 111
D. List and verify the discovered static targets and their iSCSI Qualified
Name (IQN).
3. In the Common Array Manager software: “Adding Initiator Information” on
A. Run the Create New Initiator wizard and add the IQN of the initiator page 103
as the unique identifier. Refer to the Sun StorageTek Common
B. Add each initiator to a host or host group. Array Manager Installation Guide or
C. Create the volumes. online help for the configuration of
volumes, hosts, and mappings.
D. Map each initiator to a volume using the host or host group.
4. On the data host: OS Documentation
A. If needed, create a device link. (Example for Solaris: #devfsadm -i “iSCSI Configuration Example
iscsi.) Using Solaris” on page 107
B. Verify that you can see the created volume. “iSCSI Configuration Example
C. Optional - create and mount the file system. Using Windows” on page 111

Identifying the Target Port IP Address

Step 1 requires you to identify the target ports IP address (minimum one for each
controller) on the Port Summary page noted below.

Appendix A Configuring iSCSI on the Sun StorageTek 2510 Array 101

 .

If you need to configure the iSCSI ports to change the IP address or the listening
port, display the Port Summary and select a port to display the Port Details page.
Consult the online help for configuration help.

102 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Adding Initiator Information
After creating an initiator on a data host, you need to add information about the
initiator to the management software.

Selecting Create New Initiator launches a wizard.

Add the following information:

■ Initiator Name - can be up to 30 characters. Valid characters are 'A-Z', 'a-z', '0-9',
hyphen('-') and underscore('_').
■ Unique Identifier - enter the IQN of the iSCSI initiators found on the data host
(See Step 2A on page 95). The identifier is used like a WWN in FC storage.
(The identifier can also be in EUI or NAA format. See the online help for the
syntax of these formats.)
IQN syntax example: iqn.2001-04.com.example:storage:diskarrays-
sn-a8675309:
■ iqn - specifies the type of address
■ 2001-04 - the date in yyyy-mm format
■ com.example:storage - the naming authority
■ diskarrays-sn-a8675309 - is the string defined by the naming authority.
■ Host type - specifies the OS and failover method of the data host.

Appendix A Configuring iSCSI on the Sun StorageTek 2510 Array 103

 ■ Initiator's Host - select from a list of existing hosts or create a new one.

The wizard will allow you to assign the initiator to a host or host group. You use the
host or host group to map the initiator to a volume.
■ Authentication - enable Challenge-Handshake Authentication Protocol (CHAP)
authentication, if needed. (The example does not enable this). Enter a unique
password consisting of 12 to 57 alphanumeric characters.
You will also have to enter a CHAP secret on the Target Details page.
For more information about authentication, go to“Configuring Mutual
Authentication for an iSCSI Session” on page 105 for reference the online help.

Configuring Other iSCSI Features

This section describes additional features for configuring iSCSI on the Sun
StorageTek 2510 Array. It contains the following sections:
■ “Additional iSCSI Topics in the Online Help” on page 104
■ “Configuring Mutual Authentication for an iSCSI Session” on page 105

Additional iSCSI Topics in the Online Help

In addition to the initial iSCSI configuration discussed in this guide, the Common
Array Manager has online help to document modifying every feature and the fields
on every iSCSI page.

iSCSI topics in the online help include:

■ Configuring an iSCSI Session
■ Configuring Ports
■ Create Initiator Wizard
■ Configuring Mutual Authentication for an iSCSI Session
■ Configuring an Unnamed Discovery Session
■ Configuring an Internet Storage Name Service (iSNS)
■ Enabling and Disabling ICMP Ping Responses
■ Ending an iSCSI Session
■ Viewing iSCSI Performance Statistics

Page help in the online help includes:

■ iSCSI Ethernet-MAC Performance Page

104 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 ■ iSCSI Ethernet - TCP/IP Performance Page
■ iSCSI Session Details Page
■ iSCSI Ethernet-MAC Performance Page
■ iSCSI Ethernet - TCP/IP Performance Page
■ iSCSI Session Details Page
■ iSCSI Session Summary Page
■ iSCSI Target Details Page

Configuring Mutual Authentication for an iSCSI

Session
In a secure environment, authentication is not required because only trusted
initiators can access the targets.

In a less secure environment, the target cannot determine if a connection request is

truly from a given host. In that case, the target can authenticate an initiator by using
the Challenge-Handshake Authentication Protocol (CHAP).

CHAP authentication uses the notion of a challenge and response, which means that
the target challenges the initiator to prove its identity. For the challenge/response
method to work, the target must know the initiator's secret key and the initiator
must be set up to respond to a challenge.

You can configure mutual authentication for an iSCSI session so that both the iSCSI
initiator and iSCSI target use a CHAP secret.

For security purposes, Sun Microsystems recommends that the initiator and CHAP
secrets be unique.

You can add CHAP secrets when creating an initiator or add it later to an initiator
and target.

▼ To Configure Mutual Authentication

1. Click Sun StorageTek Common Array Manager.
The navigation pane and the Storage System Summary page are displayed.

2. In the navigation pane, expand the storage array you want to work with.
The navigation tree is expanded for that array.

3. Expand Physical Devices and choose Initiators.

Appendix A Configuring iSCSI on the Sun StorageTek 2510 Array 105

 The Initiator Summary page is displayed.

4. Select the initiator for which you want to configure mutual authentication.
The Initiator Details page is displayed.

5. In the Authentication field, select CHAP and enter a CHAP secret.

6. Enter the CHAP secret again in the validation field.

7. Click Save.

8. In the navigation pane, expand the storage array you want to work with.
The navigation tree is expanded for that array.

9. Expand Physical Devices and choose iSCSI Target.

The iSCSI Target Details page is displayed.

10. In the iSCSI Target Authentication section, select CHAP and enter the CHAP
secret.

11. Click Save.

106 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
APPENDIX B

iSCSI Configuration Example

Using Solaris

This appendix shows an example of iSCSI configuration on a Solaris data host in the
following sections:

“To Prepare for the iSCSI Configuration” on page 107

“To Configure iSCSI” on page 108

▼ To Prepare for the iSCSI Configuration

1. Log into the data host as super user.

2. Identify the minimum required OS, software packages, and patches by

referring to the Sun StorageTek 2500 Series Array Release Notes, 6.1 or higher.
Download from http://docs.sun.com/app/docs/coll/st2500arrays
You can also apply the latest patches from:
http://sunsolve.sun.com/show.do?target=patchpage

a. Verify that you are running the required Solaris OS:

# cat /etc/release

b. Verify that iSCSI software packages are installed

# pkginfo SUNWiscsiu SUNWiscsir
system SUNWiscsiu Sun iSCSI Device Driver (root)
system SUNWiscsir Sun iSCSI Management Utilities (usr)

c. Verify that you have the latest patches applied for the iSCSI packages. For
example:
On a SPARC system:

107
 # showrev -p | grep 119090
On an x86 system:
# showrev -p | grep 119091

3. Install the Common Array Manager software on the management host and
register the target array.
Follow the instruction in the Sun StorageTek Common Array Manager Installation
Guide.

▼ To Configure iSCSI
1. In the Common Array Manager software, go to the Port Summary page and
verify that the target ports (one for each controller) are in an up status and note
there IP addresses and ports.
If you need to change the port IP addresses, use the Port Details page. You can
enter a new IP address or set DHCP.

2. From the data host:

a. List and note the IQN of each initiator.

# iscsiadm list initiator-node

Initiator node name: iqn.1986-03.com.sun:01:0003babc0401.46f806dd

Initiator node alias: -

...

b. Enable the discovery method of the targets as static.

#iscsiadm modify discovery --static enable

c. Ping the target ports IP addresses to confirm they can be reached.

#ping ip_address

#ping 192.168.1.1

192.168.1.1 is alive

d. Discover the targets (one port for each controller) from the iSCSI initiator
using the isciadm command and the IP addresses of the ports.

#iscsiadm add discovery-address 192.168.1.1:3260

#iscsiadm add discovery-address 192.168.2.1:3260
...

108 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 e. Verify that discovered targets are listed on the data host.

#iscsiadm list discovery-address

Discovery Address: 192.168.1.1:3260

...

f. List the IQNs of the targets using the iscsiadm command and the IP
addresses you noted on the Port Summary page.

>iscsiadm list discovery-address -v 192.168.1.1

Discovery Address: 192.168.1.1:3260

Target name:
iqn.1986-03.com.sun:2510.600a0b80003487e400000000474c6e0b

Target address: 192.168.1.1:3260, 1

Target name:
iqn.1986-03.com.sun:2510.600a0b80003487e400000000474c6e0b

Target address: 192.168.1.2:3260, 1

Target name:
iqn.1986-03.com.sun:2510.600a0b80003487e400000000474c6e0b

Target address: 192.168.2.1:3260, 2

Target name:
iqn.1986-03.com.sun:2510.600a0b80003487e400000000474c6e0b

Target address: 192.168.2.2:3260, 2

g. Add the IQNs of the targets discovered in the last steps to the discovery
table.

#iscsiadm add static-config iqn.1986-

03.com.sun:2510.600a0b80003487e400000000474c6e0b,192.168.1.1
This adds a target to the list of statically configured targets. Repeat for each target
port.

h. List the statically configured targets and verify that the new targets have
been added.

# iscsiadm list static-config

Static Configuration Target:

iqn.1986-03.com.sun:2510.600a0b80003487e400000000474c6e0b,
192.168.1.1:3260
...

Appendix B iSCSI Configuration Example Using Solaris 109

 i. Note the number of disks (volumes) before you configure new volumes.

#format

AVAILABLE DISK SELECTIONS:

0. c3t0d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>

/pci@8,600000/SUNW,qlc@4/fp@0,0/ssd@w500000e010483de1,0

...

3. In the CAM software:

a. Create each initiator with its IQN from the data host noted in Step 2a.
Refer to “Adding Initiator Information” on page 103 for details.

b. Follow CAM documentation to:

■ Create a volume
■ Map the volume to a host or host group linked to the initiator.

4. On the data host:

a. Create the iSCSI device link on the data host.

#devfsadm -i iscsi

b. Issue the format command and verify that more disk (volumes) were created
than what you noted in Step 2i.

#format

The system is ready for you to use system administrator commands to create and
mount a file system.

110 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
APPENDIX C

iSCSI Configuration Example

Using Windows

This appendix shows an example of configuring iSCSI on a Windows data host

(Windows 2003 Server is the recommended platform) in the following sections:
■ “To Prepare for the iSCSI Configuration” on page 111
■ “To Configure iSCSI on Windows” on page 112

▼ To Prepare for the iSCSI Configuration

1. Download the latest iSCSI initiator tool from Microsoft
http://www.microsoft.com/downloads/details.aspx?FamilyID=12cb3c1a-15d6-
4585-b385-befd1319f825&DisplayLang=en

2. Click the downloaded .exe file to launch the install wizard.

3. Follow the instructions in the wizard until you click Finish on the last screen.
This installs the Microsoft iSCSI initiator.

4. Verify that you see the iSCSI initiator tool in the Control Panel (Start >>
Control Panel).

5. Install the Sun StorageTek Common Array Manager software on the

management host and register the target array.
Follow the instruction in the Sun StorageTek Common Array Manager Installation
Guide.

111
 ▼ To Configure iSCSI on Windows
1. Review the port settings in the Common Array Manager software and change
the IP addresses if necessary.
The IP address are on the Port Summary page. The addresses can be changed or
set to DHCP on the Port Details Page.

112 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Appendix C iSCSI Configuration Example Using Windows 113
 2. Configure the iSCSI initiator tool to be able to map the volume created on the
storage array.

a. Launch the iSCSI initiator tool from the control panel.

By default, the installation places the shortcut to the iSCSI initiator applet
on the desktop.

b. Note the IQN (iSCSI Qualified Name) of the iSCSI initiator.

3. In the CAM software, create the initiator with the IQN of the data host.
Refer to “Adding Initiator Information” on page 103 for details.

114 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
4. In the iSCSI initiator tool, go to the Discovery tab. In the Target Portals section,
add the IP address of one of the iSCSI ports on your storage array for the target
discovery.

5. Note that the Link status of the port you are adding should be UP.

Appendix C iSCSI Configuration Example Using Windows 115

 6. In the Add Target Portal pop up above, click on the Advanced button and select
the Local adapter as Microsoft iSCSI Initiator and in the Source IP. Then select
the IP of the system where the initiator is installed.

7. Click OK.

116 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
8. The target should get discovered as seen in the screen shot below.

Appendix C iSCSI Configuration Example Using Windows 117

 9. Go to the Targets tab, click on the target listed there and press Log on button.

10. Enable both the check boxes and click on the Advanced button in the pop up.

118 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
11. In the Advanced settings tab, select local adapter as the Microsoft iSCSI
Initiator.

12. For source IP, enter the system IP where the initiator is running.

13. For target portal enter the IP address you have discovered in the previous step.

14. Click OK.

After this, the status of the target should be shown as Connected.

15. Repeat Steps 7 to 14 for each target (minimum one target per controller).

16. In the Common Array Management software, configure the following using the
Common Array Management documentation (Install Guide or online help) to:
■ Create volumes
■ Map each volume to a host or host group linked to an initiator.

17. Launch the Computer Management application in Windows and open Disk
Management.

You should be able to see the mapped volume on your host.

Appendix C iSCSI Configuration Example Using Windows 119

120 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
APPENDIX D

Connecting to the 2510 Array with

Other Topologies

This appendix describes connecting data hosts to the Sun StorageTek 2510 Array
with topologies other than the basic ones listed in Chapter 4. It contains the
following section:
■ “Connecting to the 2510 Array with Other Topologies” on page 121

Connecting to the 2510 Array with Other

Topologies
Chapter 5 showed the two most common duplex cabling topologies:
■ Direct topology
■ Network topology

This section shows more examples of the above and adds:

■ Single-controller topology (not recommended)
■ Mixed topology

121
 Host Cabling Configurations – Single Controller

FIGURE D-1 Direct Connection– One Host Connected to a Single Controller

1. Host
2. NIC 1
3. NIC 2
4. Host Port 1
5. Host Port 2
6. Controller A

FIGURE D-2 Direct Topology – Two Hosts Connected in a Single Path

1. Hosts
2. NIC 1
3. NIC 2
4. Host Port 1
5. Host Port 2
6. Controller A

122 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 You can connect one or more hosts to a controller tray. The hosts can run the same
operating system or each host can run a different type of operating system.

FIGURE D-3 Fabric Topology – Two Hosts Connected to the Controller Through a Switch

1. Hosts
2. NIC 1
3. NIC 2
4. Host Port 1
5. Host Port 2
6. Controller A

FIGURE D-4 Mixed Topology – Three Hosts Connected Through a Switch or Connected
Directly

1. Host 1
2. NIC 1
3. NIC 2
4. Host 2
5. Host 3
6. Host Port 1

Appendix D Connecting to the 2510 Array with Other Topologies 123

 7. Host Port 2
8. Controller A

Host Cabling Configurations – Dual Controller

FIGURE D-5 Direct Topology – One Host Connected to Each Controller

1. Host
2. NIC 1
3. NIC 2
4. Host Port 1
5. Host Port 2
6. Controller A
7. Controller B

124 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 FIGURE D-6 Mixed Topology – Three Hosts Connected Through a Switch or Connected
Directly

1. Host 1
2. NIC 1
3. NIC 2
4. Host 2
5. Host 3
6. Host Port 1
7. Host Port 2
8. Controller A
9. Controller B

Appendix D Connecting to the 2510 Array with Other Topologies 125

126 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
CHAPTER E

Using DC Power

This appendix describes using the DC Power Source option for the Sun StorageTek
2500 Series Arrays in the following sections:
■ “DC Power Overview” on page 127
■ “Installation Notes for DC Power” on page 129
■ “Ship Kit Changes” on page 129
■ “DC Power LEDS” on page 130
■ “Connecting Power Cables” on page 130
■ “Turning Off the DC Power During an Emergency” on page 132
■ “Relocation Cautions” on page 132

DC Power Overview
The Sun StorageTek 2500 Series Arrays can be ordered with a DC power connection
and connector cables.

Caution – A qualified service person is required to make the DC power connection

per NEC and CEC guidelines. A two-pole 20-amp circuit breaker is required
between the DC power source and the trays for over-current and short-circuit
protection. Before turning off any power switches on a DC-powered CRU or module,
you must disconnect the two-pole 20-amp circuit breaker.

Caution – Electrical grounding hazard – This equipment is designed to permit the

connection of the D.C. supply circuit to the earthing conductor at the equipment.

127
 FIGURE E-1 shows the locations of the power-fan assemblies.

FIGURE E-1 Power Fan Assembly Locations.

FIGURE E-2 DC Power Connector Cable and Source Wires

The power-fan assemblies above are shown with AC power connectors. The DC
power connector can be seen in FIGURE E-3.

Caution – Risk of electrical shock – The tray has more than one power source.
To remove all power from the tray, all DC MAINS must be disconnected by
removing all power connectors (item 4 in Appendix E) from the power-fan
assemblies.

128 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Installation Notes for DC Power
The sections that follow provide hardware information about DC power.
■ “Ship Kit Changes” on page 129
■ “DC Power LEDS” on page 130
■ “Connecting Power Cables” on page 130
■ “Turning Off the DC Power During an Emergency” on page 132
■ “Relocation Cautions” on page 132

Ship Kit Changes

If the DC power option is ordered, two DC power connector cables are provided
with each controller tray for connection to centralized DC power plant equipment.

Caution – A qualified service person is required to make the DC power connection

per NEC and CEC guidelines. A two-pole 20-amp circuit breaker is required
between the DC power source and the tray for over-current and short-circuit
protection. Before turning off any power switches on a DC-powered CRU or module,
you must disconnect the two-pole 20-amp circuit breaker.

Chapter E Using DC Power 129

 DC Power LEDS
FIGURE E-3 shows the LEDs, on/off power switch, and power cable receptacle on the
back of the DC power-fan assembly.
FIGURE E-3 DC Power-Fan Assembly LEDs, Power Switch, and Power Cable Receptacle.

TABLE E-1 lists the LEDs for DC power.

TABLE E-1 DC Power-Fan Assembly LEDs
LED Color On Off
DC Power (DC Good) Green DC power from the power-fan DC power from the power-fan
assembly is available. assembly is not available.
Service Action Allowed Blue The power-fan assembly can The power-fan assembly
be removed from the tray. cannot be removed from the
tray.
Service Action Required Amber A fault exists within the Normal condition
(Fault) power-fan assembly.
Power (DC Good) Green Power is present Power is not present

Connecting Power Cables

Caution – A qualified service person is required to make the DC power

connection per NEC and CEC guidelines. A two-pole 20-amp circuit breaker is
required between the DC power source and the tray for over-current and short-
circuit protection. Before turning off any power switches on a DC-powered CRU or
module, you must disconnect the two-pole 20-amp circuit breaker.

130 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 Caution – Ensure that you do not turn on power to the controller tray or the
connected drive expansion trays until this guide instructs you to do so. For the
proper procedure for turning on the power, see ““Connecting Power Cables” on
page 130.”

Caution – Electrical grounding hazard – This equipment is designed to permit the

connection of the D.C. supply circuit to the earthing conductor at the equipment.

▼ Connecting the Cables

1. Disconnect the two-pole 20-amp DC circuit breaker for the storage array.

2. Ensure that all DC power switches on the DC-powered controller tray and all
DC power switches on any connected, DC-powered drive expansion trays are
turned off.

3. Connect the DC power connector cable to the DC power connector on each

power-fan assembly on the back of the controller tray.

Caution – The three source wires on the DC power connector cable (–48 VDC)
connect the trays to centralized DC power plant equipment, typically through a bus
bar located above the cabinet.

4. A qualified service person is required to make the DC power connection per

NEC and CEC guidelines. A two-pole 20-amp circuit breaker is required
between the DC power source and DC-powered trays for over-current and
short-circuit protection. Connect the DC power source wires on the other end of
the DC power connector cable to the centralized DC power plant equipment as
follows (see “DC Power Connector Cable and Source Wires” on page 128).

a. Connect the brown –48-VDC supply wire to the negative terminal.

b. Connect the blue return wire to the positive terminal.

c. Connect the green/yellow ground wire to the ground terminal.

5. If applicable, connect a DC power cable to each power-fan assembly on each

DC-powered drive expansion tray in the storage array.

Chapter E Using DC Power 131

 Turning Off the DC Power During an Emergency

Caution – Potential loss of data – An emergency shutdown of the storage array

might not allow the server to complete its I/O to the storage array.

Note – Before turning off the power switches on a DC-powered tray you must
disconnect the two-pole 20-amp circuit breaker.

Relocation Cautions
Use the following guidelines when relocating trays or drives from one storage array
to another.

Caution – Potential data loss – Moving a storage array or array components that are
configured as part of a volume group can result in data loss. To prevent data loss,
always consult a Customer Support representative before relocating configured
drives, controller trays, or drive expansion trays.

Note – Trays in storage arrays can be connected to the DC power supply (–48 VDC).
Before turning off any power switches on a DC-powered tray, you must disconnect
the two-pole 20-amp circuit breaker.

Do not move controller trays or drive expansion trays that are part of a volume
group configuration. If you must move array components, contact a Customer
Support representative for procedures. A Customer Support representative might
direct you to complete several tasks prior to undertaking the relocation. These tasks
might include:
■ Creating, saving, and printing an array profile of each storage array that is
affected by the relocation of a drive or tray.
■ Performing a complete backup of all data on the drives that you intend to move.
■ Verifying that the volume group and each of its associated volumes on the
affected storage array have an Optimal status.
■ Determining the location and status of any global hot spares associated with the
affected storage array.

132 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
APPENDIX F

Configuring a DHCP Server

This appendix describes how to configure bootstrap protocol (BOOTP) services in a

Sun Solaris and Microsoft Windows environment. It contains the following sections:
■ “Before You Begin” on page 133
■ “Setting Up a Solaris DHCP Server” on page 133
■ “Setting Up a Windows 2000 Advanced Server” on page 138

Dynamic IP addresses are assigned through dynamic host control protocol (DHCP)
server BOOTP services.

Before You Begin

You need each controller’s media access control (MAC) address to configure the
DHCP server. The MAC address is located on the bar code label at the back of each
controller. Since there are two controller modules per controller tray, you need two
MAC addresses.

Setting Up a Solaris DHCP Server

The following procedure provides an example of how to set up a DHCP server with
the BOOTP option for the Solaris 8, 9, and 10 Operating Systems. Your environment
may require different steps.

1. Modify the netmasks line of the /etc/nsswitch.conf file as shown here:

#netmasks: nis [NOTFOUND=return] files

133
 netmasks: files nis [NOTFOUND=return]

2. Start the DHCP wizard by issuing the following command at the command
line:

/usr/sadm/admin/bin/dhcpmgr &

The following window is displayed:

The wizard will prompt you for information related to the configuration, network
address, and subnet mask of the controller tray. Select or enter the following
information:
■ Data storage format: Text files
■ Name service to store host records: Do not manage hosts records
■ Length of lease:
■ Network Address: Network address of Controller A
■ Subnet Mask: For example, 255.255.255.0
■ Network Type: Local-Area (LAN)
■ Router: Use router discovery protocol

Your summary page should look similar to the following example:

134 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
3. Verify your configuration information, and click Finish.

4. When you are prompted to configure addresses for the server, click Yes.
The Add Address to Network wizard is displayed.

5. Enter the following information:

■ Number of IP addresses
■ Name of managing server
■ Starting IP address
■ Configuration macro to be used for configuring the clients
■ Lease type

Your summary page should look similar to the following example:

Appendix F Configuring a DHCP Server 135

 6. Verify your configuration information and click Finish.
The DHCP Manager displays the following:

7. In the Address Properties window, do the following:

a. In each Client ID field, enter 01 followed by the MAC address that is

printed on the back of the controller. For example:
0100A0E80F924C

b. Toward the bottom of the window, select “Assign only to BOOTP clients.”

136 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 c. Click OK.
The DHCP manager updates the status and client ID, as shown in the
following example:

8. Go to Modify Service Options, and do the following:

a. Select Detect Duplicate IP addresses.

b. Under BOOTP Compatibility, select Automatic.

c. Select Restart Server, as shown in the following example.

Appendix F Configuring a DHCP Server 137

 d. Click OK.

After the configuration process has finished, the DHCP server provides BOOTP
services to the MAC address you entered for each controller.

9. To verify that the BOOTP service is running, go to Service >> Restart.

10. After you power on the storage array, ping the address.
If the ping responds with ‘alive’, the DHCP server BOOTP operation was
successful.

Setting Up a Windows 2000 Advanced

Server
Before you begin, make sure the following requirements are met:
■ Windows 2000 server and the storage array are both on the same subnet.
■ IP addresses that are assigned to the controllers do not conflict.

138 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
■ The array is in BOOTP IP addressing mode (the default setting for a new array).
■ The Windows 2000 Server setup CD is available.

The following procedure provides an example of how to set up DHCP with the
BOOTP option on the Windows 2000 Advanced Server. Your environment might
require different steps.

Installing the DHCP Server

To install DHCP server on the Windows 2000 Advanced Server:

1. From the Control Panel, go to Administrative Tools >> Configure Your Server.

2. Select DHCP from the Networking drop-down menu on the left.

The wizard instructs you to use the Windows Components wizard to add the
DHCP component.

3. Start the Windows Components wizard and double-click Networking Services.

4. Select Dynamic Host Configuration Protocol (DHCP), click the check box to its
left, and click OK.
The Windows Components wizard is displayed.

5. Click Next.

6. If Terminal Services Setup is displayed, select Remote administration mode.

Click Next.
If your server has obtained an address from a DHCP server for its own address, a
warning is displayed.

7. Click OK to accept the warning.

Local Area Connection Properties is displayed.

8. Assign a static IP address to the server, or click Server to keep DHCP

addressing for the server. Click OK.

9. Click Finish to exit the Windows Components wizard.

The DHCP server is now installed. The next step is to configure the server.

Configuring the DHCP Server

To configure the DHCP server:

Appendix F Configuring a DHCP Server 139

 1. From the Control Panel, go to Administrative Tools >> Computer Management
>> Services and Application >> DHCP.

2. From the Action menu, select New Scope.

The New Scope wizard is displayed.

3. Enter the following information as prompted:

■ Scope name and description:
■ IP address range (for example, 192.168.0.170 to 192.168.0.171)
■ Subnet mask (for example, 255.255.255.0)
■ Add exclusions (do not exclude any IP addresses)
■ Lease duration (accept the default of 8 days)
■ Router (default gateway) of your subnet (for example, 192.168.0.1)
■ Domain name, WINS server (these are not needed)
■ Activate Scope? (select “Yes, I want to activate this scope now”)

4. Click Finish to exit the wizard.

The contents of the DHCP server are listed.

5. Right-click Scope [ipaddress] scope-name and select Properties.

6. In the Scope Properties box, click the Advanced tab.

7. Select BOOTP only, set the lease duration to Unlimited, and click OK.

8. Right-click Reservations.
The Controller A Properties box is displayed.

9. Enter the IP address and the MAC address for Controller A. Click Add.
The Controller B Properties box is displayed.

10. Enter the IP address and the MAC address for Controller B. Click Add.
The controllers are added to the right of the Reservations listing.

11. Right-click Scope [ipaddress] scope-name to disable the scope.

12. Click Yes to confirm disabling of the scope.

13. Right-click Scope and select Activate.

The DHCP server is now configured with the BOOTP option for the array
network.

14. Power on or power cycle the array modules.

15. Click Address Leases in the left pane to check the DHCP server leases.
The lease expiration displays the following status for each controller:

140 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Reservation (active)

If the lease expiration for the controllers is inactive, try refreshing the list. If the lease
is still inactive, check the following:
■ Are the IP addresses allocated for BOOTP conflicting?
■ Were the correct MAC addresses added to the DHCP server for the controllers?
■ Are the DHCP server and storage array on the same subnet?
■ Is the gateway configured correctly on the DHCP server?
The controllers can gain a lease and an IP address, but they cannot respond out of
the subnet for the software if the gateway is not configured properly.
■ Are the controllers set up for BOOTP access?
It is possible that they were previously configured to have static IP addresses. You
must be sure when you move an array that you change the array’s IP addresses to
IP addresses on the new subnet before setting up BOOTP services.

Appendix F Configuring a DHCP Server 141

142 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
Glossary

Definitions obtained from the Storage Networking Industry Association (SNIA)

Dictionary are indicated with “(SNIA)” at the end. For the complete SNIA
Dictionary, go to www.snia.org/education/dictionary.

agent

The component of the system monitoring and diagnostic software that collects
health and asset information about the array.

alarm

A type of event that requires service action. See also event.

alert

A subtype of an event that requires user intervention. The term actionable event often
describes an alert. See also event.

array

Multiple disk drives that function as a single storage device. A high-availability

(HA) array configuration has redundant controllers and expansion trays of disk
drives.

array hot-spare

A disk that serves as a hot-spare within an array as part of the storage pool; a
reserve disk that can be made available to all virtual disks within an array. See also
hot-spare.

block

The amount of data sent or received by the host per I/O operation; the size of a data
unit.

143
 capacity

The amount of storage you must allocate to storage elements, including volumes,
pools, and virtual disks. Capacity planning should include allocations for volume
snapshots and volume copies.

CLI

Command-line interface. The SSCS command-line interface is available from the

remote CLI client or through an SSCS directory on the Solaris Operating System
management software station.

controller tray

A tray with an installed redundant RAID controller pair. In a Sun StorageTek 2500
Series array, 1x1, 1x2, 1x3, and 1x4 array types are available.

control path

The route used for communication of system management information, usually an

out-of-band connection.

customer LAN

See site LAN.

DAS

See direct attached storage (DAS).

data host

Any host that uses the system for storage. A data host can be connected directly to
the array (direct attach storage, or DAS) or can be connected to an external switch
that supports multiple data hosts (storage area network, or SAN). See also host.

data path

The route taken by a data packet between a data host and the storage device.

direct attached storage (DAS)

A storage architecture in which one or two hosts that access data are connected
physically to a storage array.

disk

A physical drive component that stores data.

event

A notification of something that happened on a device. There are many types of

events, and each type describes a separate occurrence. See also alarm and alert.

144 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
expansion tray

A tray that does not have a RAID controller, used to expand the capacity of an array.
This type of tray must be attached to a controller tray to function.

extent

A set of contiguous blocks with consecutive logical addresses on a physical or

virtual disk.

failover and recovery

The process of changing the data path automatically to an alternate path.

fault coverage

The percentage of faults detected against all possible faults or against all faults of a
given type.

FC

See Fibre Channel (FC).

Fibre Channel (FC)

A set of standards for a serial I/O bus capable of transferring data between two
ports at up to 100 megabytes/second, with standards proposals to go to higher
speeds. Fibre Channel supports point to point, arbitrated loop, and switched
topologies. Fibre Channel was completely developed through industry cooperation,
unlike SCSI, which was developed by a vendor and submitted for standardization
after the fact.

Fibre Channel switch

A networking device that can send packets directly to a port associated with a given
network address in a Fibre Channel storage area network (SAN). Fibre Channel
switches are used to expand the number of servers that can connect to a particular
storage port. Each switch is managed by its own management software.

field-replaceable unit (FRU)

An assembly component that is designed to be replaced on site, without the system

having to be returned to the manufacturer for repair.

FRU

See field-replaceable unit (FRU).

HBA

See host bus adapter (HBA).

Glossary 145
 host

As a function of the Sun StorageTek 2500 Series array configuration, a representation

of a data host that is mapped to initiators and volumes to create a storage domain.
See also data host, initiator.

host bus adapter (HBA)

An I/O adapter that connects a host I/O bus to a computer’s memory system.
Abbreviated HBA. Host bus adapter is the preferred term in SCSI contexts. Adapter
and NIC are the preferred terms in Fibre Channel contexts. The term NIC is used in
networking contexts such as Ethernet and token ring. See also initiator.

host group

A group of hosts with common storage characteristics that can be mapped to

volumes. See also host.

hot-spare

The drive used by a controller to replace a failed disk. See also array hot-spare.

in-band traffic

System management traffic that uses the data path between a host and a storage
device. See also out-of-band traffic.

initiator
A system component that initiates an I/O operation over a Fibre Channel (FC) or iSCSI
Ethernet network. If so configured, each host connection within the network has the
ability to initiate transactions with the storage array. Each host in the network represents
a separate initiator, so if a host is connected to the system through two host bus adapters
(HBAs) or NICs, the system identifies two different initiators (similar to multi-homed,
Ethernet-based hosts). In contrast, when multipathing is used in round-robin mode,
multiple HBAs or NICs are grouped together, and the multipathing software identifies
the group as a single initiator.

IOPS

A measure of transaction speed, representing the number of input and output

transactions per second.

iSCSI

iSCSI is an acronym for internet SCSI (Small Computer System Interface). This
storage networking standard transports block level data and SCSI commands as IP
packets over Ethernet as described in RFC 3720.

LAN

Local area network.

146 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
logical unit number (LUN)

The SCSI identifier for a volume as it is recognized by a particular host. The same
volume can be represented by a different LUN to a different host.

LUN

See logical unit number (LUN).

MAC address

See media access control (MAC) address.

management host

A Solaris host serving the configuration, management, and monitoring software for
the Sun StorageTek 2500 Series array. The software on the station can be accessed
with a browser to run the browser interface or with a remote scripting command-
line interface (CLI) client to access the SSCS CLI commands.

master / alternate master

A design for reliability that uses redundant configuration. Array configurations

share master/alternate master configurations: each array configuration has two
controller trays that are grouped as one host. In each case, the master component
uses the IP address and name. If the master fails, the alternate master assumes the IP
address and name and takes over the master’s functions.

media access control (MAC) address

The physical address identifying an Ethernet controller board. The MAC address,
also called an Ethernet address, is set at the factory and must be mapped to the IP
address of the device.

mirroring
A form of storage – also called RAID Level 1, independent copy, and real-time copy –
whereby two or more independent, identical copies of data are maintained on separate
media. Typical mirroring technologies enable the cloning of data sets to provide
redundancy for a storage system.

multipathing

A design for redundancy that provides at least two physical paths to a target.

out-of-band traffic

System management traffic outside of the primary data path that uses an Ethernet
network. See also in-band traffic.

PDU

See power distribution unit (PDU).

Glossary 147
 pool

See storage pool.

power distribution unit (PDU)

The assembly that provides power management for the system. The redundant
design uses two PDUs in each system so that the system’s data path continues to
function if one of the PDUs fails.

profile

See storage profile.

provisioning

The process of allocation and assignment of storage to hosts.

RAID

An acronym for Redundant Array of Independent Disks, a family of techniques for

managing multiple disks to deliver desirable cost, data availability, and performance
characteristics to host environments. Also, a phrase adopted from the 1988 SIGMOD
paper A Case for Redundant Arrays of Inexpensive Disks.

remote monitoring

Monitoring of the functions and performance of a hardware system from a location

other than where the hardware resides.

remote scripting CLI client

A command-line interface (CLI) that enables you to manage the system from a remote
management host. The client communicates with the management software through a
secure out-of-band interface, HTTPS, and provides the same control and monitoring
capability as the browser interface. The client must be installed on a host that has
network access to the system.

SAN

See storage area network (SAN).

site LAN

The local area network at your site. When the system is connected to your LAN, the
system can be managed through a browser from any host on the LAN.

148 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
snapshot

An copy of a volume’s data at a specific point in time.

SSCS

Sun Storage Command System. The command-line interface (CLI) that can be used
to manage the array.

storage area network (SAN)

An architecture in which the storage elements are connected to each other and to a server
that is the access point for all systems that use the SAN to store data.

storage domain
A secure container that holds a subset of the system’s total storage resources. Multiple
storage domains can be created to securely partition the system’s total set of storage
resources. This enables you to organize multiple departments or applications into a single
storage management infrastructure.

storage pool

A container that groups physical disk capacity (abstracted as virtual disks in the
browser interface) into a logical pool of available storage capacity. A storage pool’s
characteristics are defined by a storage profile. You can create multiple storage pools
to segregate storage capacity for use in various types of applications (for example,
high throughput and online transaction-processing applications).

storage profile
A defined set of storage performance characteristics such as RAID level, segment size,
dedicated hot-spare, and virtualization strategy. You can choose a predefined profile
suitable for the application that is using the storage, or you can create a custom profile.

storage tray

An enclosure containing disks. A tray with dual RAID controllers is called a

controller tray; a tray without controllers is called an expansion tray.

stripe size

The number of blocks in a stripe. A striped array’s stripe size is the stripe depth
multiplied by the number of member extents. A parity RAID array’s stripe size is the
stripe depth multiplied by one less than the number of member extents. See also
striping.

striping
Short for data striping; also known as RAID Level 0 or RAID 0. A mapping technique in
which fixed-size consecutive ranges of virtual disk data addresses are mapped to
successive array members in a cyclic pattern. (SNIA).

Glossary 149
 target

The system component that receives a SCSI I/O command. (SNIA).

thin-scripting client

See remote scripting CLI client.

tray

See storage tray.

virtual disk

A set of disk blocks presented to an operating environment as a range of

consecutively numbered logical blocks with disk-like storage and I/O semantics.
The virtual disk is the disk array object that most closely resembles a physical disk
from the operating environment’s viewpoint.

volume
A logically contiguous range of storage blocks allocated from a single pool and presented
by a disk array as a logical unit number (LUN). A volume can span the physical devices
that constitute the array, or it can be wholly contained within a single physical disk,
depending on its virtualization strategy, size, and the internal array configuration. The
array controller makes these details transparent to applications running on the attached
server system.

volume snapshot

See snapshot.

WWN

World Wide Name. A unique 64-bit number assigned by a recognized naming

authority such as the Institute of Electrical and Electronics Engineers (IEEE) that
identifies a connection (device) or a set of connections to the network. The World
Wide Name (WWN) is constructed from the number that identifies the naming
authority, the number that identifies the manufacturer, and a unique number for the
specific connection.

150 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 Index

A cabling
about installing data host software for non-Solaris 1x2 array configuration, 49
host, 85 1x3 array configuration, 50, 51
about IP addressing, 89 Ethernet ports directly to management host, 57
Ethernet ports to a management LAN, 56
array
Ethernet ports using a hub, 56
about IP addressing, 89
I/O module, 15
cabling a 1x2 configuration, 49
intertray connections, 46
cabling a 1x3 configuration, 50, 51
power connections, 46
configuration naming convention, 47
to a 2510, 59
configuring controller IP addressing, 89
to a ST2510, 121
installation checklist for, 4
to a ST2530, 63
powering on, 78
to a ST2540, 69
powering-off, 79
pre-installation process for, 4 cache memory
battery, 9
authentication, 98
ST2510 controller, 13
ST2530 controller, 12
B ST2540 controller, 10
backup power, battery cache memory, 9 CHAP authentication, 98
battery comments
backup power, 9 submitting to Sun, xi
cache memory, 9
configuration naming convention, 47
book
Configuration wizard for DHCP, 134
related documentation, x
submitting comments to Sun, xi configuring controller IP addressing, 89
configuring DHCP IP addressing, 90
C configuring IP addressing using the controller serial
cabinet, 2 port, 91
attaching rails to a standard 19-inch cabinet, 31 configuring static IP addressing, 91
attaching rails to a Sun Rack 900/1000, 31 connecting a terminal to a controller serial port, 91
controller tray slot, 30 connecting power cables, 46
installing a tray, 41 connecting the management host, 55
preparing for tray installation, 30 connectors

151
 data host, 10 setting up, 82
I/O module SAS, 15 data host software
management host, 9 about installing for a non-Solaris host, 85
SAS, ST2510, 13 downloading software for a non-Solaris OS, 86
SAS, ST2530, 12 installing for a non-Solaris host, 83, 85, 86
SAS, ST2540, 10 data path redundancy, 9
contact tech support, xi DC power option
contents power source wires, 131
universal rail kit, 28 DHCP
controller Configuration wizard for, 134
configuring IP addressing, 89 server configuration
connecting a terminal to the serial port, 91 before you begin, 133
connecting Ethernet ports to a management Solaris DHCP server setup, 139
LAN, 56 Windows 2000 Advanced Server
connecting Ethernet ports to directly to installation, 139
management host, 57 Windows 2000 Advanced Server
connecting using an Ethernet hub, 56 requirements, 138
establishing communication between a terminal DHCP IP addressing
and the serial port, 92 configuring, 90
using the serial port to configure IP
direct topology, 60
addressing, 91
disk drives
controller tray
description of
installation slot in cabinet, 30
ST2540 controller tray
ship kit contents, 29
controller trays
disk drives, 22
maximum connection number, 10, 12, 13
CRUs, 9
numbering scheme, 23
Ethernet connection for out-of-band
tray ID and slot designation, 23
management, 9
fiber-optic interface, ST2540, 10 documentation
front-access components, 5 accessing from Sun, xi
LEDs on the front, 6 related, x
rear-access components, 8 downloading data host software for a non-Solaris
SAS connectors, ST2540, 10 host, 86
SFP transceivers, 11 drive expansion tray
ST1530 model, description of, 12 front-access components, 5
ST2510 model, description of, 13 I/O module, 14
CRUs LEDs on the front, 6
controller trays, 9 overview, 2
power-fan assembly, 14 rear-access components, 8, 9
ST2510 controller, 13 SAS connectors, 15
ST2530 controller, 12
ST2540 controller, 10 E
emulation
D setting up a terminal, 92
data host enabling multipathing software, 86
cabling to a 2510, 59, 121 end caps
cabling to a 2530, 63 removing, 43
cabling to a 2540, 69 replacing, 45

152 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
establishing communication between a terminal and 1x3 configuration, 50, 51
a controller serial port, 92 IP addressing
Ethernet connection about, 89
controller trays, 9 configuring DHCP, 90
Ethernet ports configuring for array controllers, 89
connecting directly to management host, 57 configuring static, 91
connecting to a management LAN, 56 using the controller serial port, 91
connecting using a hub, 56 iSCSI
expansion tray configuration, 97
ship kit contents, 30 definition, 146
session, 98
F Solaris example, 107
fabric topology, 60 target, 98
Windows example, 111
fans
power-fan assembly, 14 iSCSI initiator, 98
fault LED, 21 iSCSI Qualified Name (IQN), 101
Fibre Channel
ST2540 controller tray, 10 L
LEDs
firmware, 10
fault, 21
front-access tray components, 5
on the front of the trays, 6
on the rear of the ST2510 controller tray, 16
H on the rear of the ST2540 controller tray, 16
host on the rear of the trays, 16
cabling to a 2510, 59, 121 power-fan assembly, 19
cabling to a 2530, 63 Service Action Allowed, 21
cabling to a 2540, 69
connecting for management, 55 M
setting up a data host, 82
MAC address, 10
hot swap
MAC address location, 133
controller CRUs, 9
I/O module, 14 management host
connecting, 55
connector cable types, 10
I
multipathing software
I/O module
enabling, 86
cabling, 15
ST2501 drive expansion tray, 14
N
initiator, 98
network topology, 60
installation process, 4
New Scope wizard, 140
installing a tray in a cabinet, 41
installing data host for a non-Solaris host, 86
O
installing data host software for a non-Solaris out-of-band management, 9
host, 86
installing data host software for non-Solaris P
host, 83, 85
part numbers
intertray cabling, 46 universal rail kit, 28
1x2 configuration, 49

Index 153
planning the tray installation order, 30 establishing communication with a terminal, 92
power setting up terminal emulation, 92
connecting cables, 46 using to configure IP addressing, 91
power-fan assembly serial port cable, 91
description of, 14 Service Action Allowed LED, 21
fan, description of, 14 session
LEDs, 19 iSCSI, 98
powering off the array, 79 setting up a data host, 82
power-on procedures setting up terminal emulation, 92
array, 78 SFP transceivers
before powering-on, 77 description of, 11
preparing the cabinet for tray installation, 30 ship kit
preparing the tray for installation, 29 controller tray, 29
product overview expansion tray, 30
software, 25 single-controller configuration, 122
single-controller configurations, 54
R single-controller topology, 60
rackmount kit preparation, 28 software
rails enabling multipathing, 86
attaching to standard 19-inch cabinet, 31 installing data host for non-Solaris host, 83, 85
attaching to Sun Rack 900/1000, 31 software overview, 25
attaching to unthreaded cabinet
ST2500 drive expansion tray
attaching rails to unthreaded cabinet, 35
disk drives, 22
loosening length adjustment screws, 28
ST2501 drive expansion tray
rear-access components of the controller trays, 8
I/O module, 14
rear-access components of the drive expansion power-fan assembly, 14
tray, 8, 9
ST2510 controller tray
redundancy power-fan assembly, 14
data path, 9
St2510 controller tray
I/O module, 14
LEDs on the rear, 16
related documentation, x
ST2530 controller tray
RJ45-DB9 adapter, 91 disk drives, 22
RJ45-DIN cable, 91 power-fan assembly, 14
pinouts, 92 ST2540 controller tray
LEDs on the rear, 16
S power-fan assembly, 14
SAS connector, ST2510, 13 static IP addressing
SAS connector, ST2530, 12 configuring, 91
SAS connectors storage array configuration
ST2501 drive expansion tray, 15 2500 Series Array Product Overview, 3
serial cable switched topology, 60
pinouts, 92
serial connection by USB, 91 T
serial connection to PC, 91 target
serial port iSCSI, 98
connecting a terminal, 91 ports, 101

154 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008
 static, 101
technical support, xi
terminal
connecting to a controller serial port, 91
establishing communication with a controller
serial port, 92
setting up emulation, 92
tools
required for tray installation, 27
topology, 59, 60, 63, 69, 121
Traffic Manager
downloading, 84
installing, 85
training web site, xi
tray
installation order, 30
installing, 41
intertray cabling, 46
preparing for installation, 29
preparing the cabinet for installation, 30
ship kit contents, 29, 30
tools required for installation, 27
unpacking, 29
tray ID
disk drives, 23
tray installation
preparing the rackmount kit for, 28
trays
front-access components, 5, 6
LEDs on the rear, 16
rear-access components, 8

U
universal rail kit
attaching to a standard 19-inch cabinet, 31
attaching to a Sun Rack 900/1000, 31
attaching to unthreaded cabinet, 35
contents, 28
part numbers, 28
unpacking a tray, 29

Index 155
156 Sun StorageTek 2500 Series Array Hardware Installation Guide • November 2008