Assignment 5
Assignment 5
Structural concepts
Smudge 9000 - CC - BY
AE1110x - Introduction to Aeronautical Engineering
Exercise 1
Which of the following is/are functions of a structure in aviation?
A) Provide support
B) Provide stiffness and strength
C) Provide durability
D) Provide enough space for the interior
E) Protect the interior
Exercise 2
Put the materials and structural concepts mentioned below to the most applicable time period.
You are allowed to put multiple items in one box.
Carbon fibre - Pressure cabin - Linen - Aluminium - Aluminium alloys - Cables - Composites -
Wooden spars
Exercise 3
Between 1903 and 1940, a significant change has taken place on the skin of aircraft wings and
fuselages. What change is this?
A) The wing and fuselage skin have become increasingly thinner
B) The wing and fuselage skin went from non-loaded to load-carrying
C) The fuselage skin has been optimised to incorporate windows
D) The wing and fuselage skin were eventually made of different materials
Exercise 4
You are given the following statements on biplanes:
1) Placing two identical wings on top of each other increases lift by about 50%, compared to
having just one wing.
2) Biplanes usually have a higher glide ratio than monoplanes.
Exercise 5
What was the most important feature of the Fokker F VII, shown below?
Exercise 6
You are given the following two statements:
1) A webplate is the vertical segment of a beam element.
2) In a safe-life design we need to take into account large safety factors.
Which of the following is true:
A) Only statement 1 is correct
B) Only statement 2 is correct
C) Both statements are correct
D) Neither statement is correct
Exercise 7
Below you see a picture of the Millau bridge, one of the highest bridges on the world. What will
have been the design philosophy behind the vertical columns of this bridge?
Exercise 8
You are given the following statements:
1) In the truss shown below, the bottom side is in tension.
2) The directions of the web forces shown are correct.
Exercise 9
The truss shown below is loaded by a force F. What must the compressive force in the bottom
(circled in red) be?
Exercise 10
What is the definition of a shell structure, as given in the lecture?
"A shell structure is a __(1)__ , __(2)__ skin, with __(3)__ elements."
1) Broad, Thick, Thin or Optimised
2) Adequate, Force-carrying, Load-bearing, Optimised or Strong
3) Reinforcing, Stiffening, Strengthening or Supporting
Exercise 11
What does the abbreviation PSE stand for, when we talk about aircraft structures?
Exercise 12
Some aircraft are capable of flying upside down. Suppose that an aircraft cruises upside down,
then what it its load factor?
Exercise 13
An aircraft tries to make turn by banking, see the figure below. The angle φ (’phi’) is its bank
angle. The aircraft makes its turn in such a way that it maintains a constant altitude.
Exercise 14
An aircraft component has an ultimate load of 5.28 kN and a limit load of 1.32 kN.
1) What is its safety factor?
2) Based on this safety factor, do you think it was designed using a fail-safe philosophy or a safe-life
philosophy?
Exercise 15
Finish the following statement.
Fatigue is caused by:
A) A constant force, smaller than the breaking force.
B) A cyclic force, greater than the breaking force.
C) A cyclic force, smaller than the breaking force.
D) A repeated load, greater than the breaking force.
E) A repeated load, smaller than the breaking force.
F) An irregular force, smaller than the breaking force.
Exercise 16
Which two phases (before a critical crack) do we distinguish in the process of fatigue?
Exercise 17
A modern jet flies at an altitude of 6,200 metres, during its climb to cruise altitude. For additional
passenger comfort, the cabin pressure is maintained at 80% of the sea level value.
1) Given that the fuselage radius is 3.2 metres and that the skin thickness is 2.4 mm, compute the
circumferential stress in the fuselage skin (in MPa or MegaPascal): (Assume ISA conditions)
2) Additionally, compute the longitudinal stress in the fuselage skin (in MPa or MegaPascal):
Exercise 18
A young engineer has come up with a ’brilliant idea’: an aircraft with a square fuselage for more
space. Since all aircraft have a circular fuselage cross section you suspect there must be a down-
side to this plan and you suspect it has to do with stress in the fuselage skin due to the cabin
pressure.
To convince the young engineer, you have to determine the ’circular’ stress in the fuselage due to
the cabin pressure as a function of R, pin , pout and t. To do so, make use of the figure below.
1) Give an equation for the ’circular’ skin stress σ, as a function of the variables in the picture
above.
2) What will your main argument of why a square fuselage is not a good idea be?
A) "A square fuselage is not aerodynamic".
B) "In a square fuselage the skin stress due to the cabin pressure is higher".
C) "A square fuselage is heavier."
D) "A square fuselage will experience major bending stresses, which a circular fuselage does not."
Exercise 19
A futuristic Aircraft manufacturer has come up with the idea to build a supersonic passenger jet,
which is supposed to perform cruise flight at 24 kilometres altitude. For passenger comfort, the
cabin pressure should remain at least 72 percent of the sea level value. To give the aircraft an
aerodynamic shape its fuselage is rather long and slender, meaning the fuselage diameter is ’just’
4.5 metres.
The engineers have asked you, now experts in the field of pressure cabins and fatigue, to determine
the required skin thickness to deal with the circular stress (which may not exceed 75MPa) in the
fuselage skin. To be on the safe side, they ask you to take into account a safety factor of 1.5.
What will be for this aircraft the skin thickness (in millimetres)?