AVENTOS HF Wood/wide aluminum

frame door application

Lift mechanism set

▀▀ Lift mechanism (qty 2)
▀▀ #7 x 35 mm (1-3/8”) wood screw (qty 8)

Power factor Part no.

85 — 230 (1 lift mechanism req.) 20F2200.N5

231 — 470 20F2200.N5

471 — 880 20F2500.N5

780 — 1440 20F2800.N5

1401 — 2300 (3 lift mechanisms req.) 20F2800.N5

Cover set
▀▀ Right and left cover plate
▀▀ Non-handed cover cap (qty 2)
Part no.
Cover set 20F8000.NA

Telescopic arm set

▀▀ Telescopic arm (qty 2)

Cabinet heights Part no.

479 (18-7/8") — 558 (22") 20F3200.01

558 (22") — 686 (27") 20F3500.01

686 (27") — 889 (35") 20F3800.01

889 (35") — 1067 (42") 20F3900.01

Wood or wide alum door hardware set Mounting plate with bracket set
▀▀ CLIP top 120° hinge (qty 2) ▀▀ Left and right mounting plate with bracket
▀▀ COMPACT 33° hinge (qty 2) ▀▀ For large overlay five-piece doors

▀▀ CLIP top bottom door hinge (qty 2)

▀▀ COMPACT mounting plate (qty 2)
▀▀ Face frame adapter (qty 4)
▀▀ Telescopic arm mounting plate (qty 2)

NOTE: Three hinges and mounting plates required

for cabinet widths over 1219 (48") Part no.
Hardware set 78Z5530TA8

Inst. screw for wood doors 606N or 606P Part no.

Inst. screw for wide alum doors 7072A Mounting plate w/ bracket set 175H3F00

Subject to technical modifications without notice. © 2018 1

 Assembly

WARNING
Risk of injury from spring-loaded arm
▀▀ Do not push arm assembly down or leave in the down position
▀▀ Remove mechanism before installing or removing cabinet

1 Locating pin locations

Panel
TR
Y

Ø5 Top door height

Top door height

(TDH) Y

192 37 231 to 271 TDH x .6 - 28 + TR

272 to 531 TDH x .6 - 57 + TR
TR = Top reveal
TDH = Top door height

Face frame
Y

TR

Ø5

192 37
TDH

Top door height

(TDH) Y

231 to 271 TDH x .6 - 28 + TR

NOTE: Face frame
cabinets must be blocked 272 to 531 TDH x .6 - 57 + TR
out flush with the frame
TR = Top reveal
TDH = Top door height

Part no.
Universal individual template is available for pre-boring locating pins 65.1051.02

2 Subject to technical modifications without notice. © 2018

2 Attaching the lift mechanism

Align the lift mechanism in the cabinet using the 5 mm locator pins and attach the mechanism with the four
wood screws provided.

min 5

#7 x 35 mm (1-3/8") wood screws (qty 4)

3 Attach the telescopic arms

WARNING: Risk of injury from spring loaded arm.

Attach telescopic arms by clipping them on in

the fully upright position.

Subject to technical modifications without notice. © 2018 3

 Assembly

4 Small overlay top door hinge planning CLIP top hinges

overlay
B
Overlay table

13* 14 15 16 17

3 3 4 5 6
B Bore distance
12.7 * Bore at 3 then adjust 1

Part no.
CLIP top hinge 70T5580.TL
Mounting plate 175H6000

5 Large overlay top door hinge planning COMPACT hinges

overlay
B

Overlay table

1-1/4”

3
Bore distance

1/2"

Part no.
COMPACT hinge 32.4630
Mounting plate 130.1130.02

4 Subject to technical modifications without notice. © 2018

6 Bottom door hinge planning

reveal
Reveal table

6 5 4 3

3 4 5 6
B

B Bore distance

12.7

Part no.
CLIP top hinge 78Z5530T
Mounting plate 175H6000

7a Attaching the telescopic arm mounting plates

Top door
X
height (TDH)
TDH

231 to 271 TDH x .5 + 70

272 to 531 TDH x .5 + 47

NOTE: For five-piece door mounting

specifications, see page 6
X
min.
17

12.5 + Overlay

Part no.
Telescopic arm mounting plate 175H3100

Subject to technical modifications without notice. © 2018 5

 Assembly

7b Attaching the telescopic arm mounting plate with bracket for five-piece doors

Standard mounting plate works

ü 12.5

more▀than 6

Standard mounting plate does not work

12.5

less▀than 6

Use mounting plate with bracket when

panel is < 6 mm from screw ü 12.5

19

Part no.
Telescopic arm mounting plate with bracket 175H3F00

6 Subject to technical modifications without notice. © 2018

8 Attach the top door to the cabinet

9 Attach the bottom door

Attach bottom door to the top door and attach the telescopic arms
1

a b

Subject to technical modifications without notice. © 2018 7

 Assembly

10 Adjust tension of the mechanism

1 2

Close and flush doors to cabinet. Open and close door to test closing force. Use a screw gun and the #2x2 POZI
driver bit to adjust the lift mechanism to the desired tension. Test door again and repeat until ▀
desired function is achieved.

Tension adjustment should be the same on both lift mechanisms.

11 Finalizing the door adjustments

1 2

± 3 mm ± 2 mm + 3/- 2 mm ± 2.5 mm ± 2 mm ± 2 mm

1. Adjust each top door hinge and mounting plate 2. Adjust each bottom door hinge and mounting
to properly align the top door to the cabinet. plate to properly align doors to the cabinet and
to the top door.

Although not illustrated here, telescopic arm mounting plates can also be adjusted horizontally ± 2 mm if needed.

8 Subject to technical modifications without notice. © 2018

12 Adjust and lock telescopic arms

1 2

Open door
enough to ▀
lock levers

1. Close and flush doors to cabinet. While pressing on 2. Slightly open door and lock the telescopic arms
the top door, pull the bottom door open one inch. into position using the levers as shown.

13 Attach covers

Attach the left and right cover plates to each lift mechanism then attach the symmetrical cover caps

Subject to technical modifications without notice. © 2018 9

 Removal

WARNING
Risk of injury from spring-loaded arm
▀▀ Do not push arm assembly down or leave in the down position
▀▀ Remove mechanism before installing or removing cabinet

1 Remove covers

2 Detaching the telescopic arms

Warning: Risk of injury

1 from spring-loaded
telescopic arm!

Maintain control of telescopic arm while

releasing the CLIP mechanism.

Release both arms and gently rest the top

door on the loose arms. The tension will hold
the doors up for the next step.

10 Subject to technical modifications without notice. © 2018

 3 Removing the doors

11. Hold the bottom door while unclipping the bottom hinges.

22. Hold the top door while detaching the top hinges. Simply unclip them if using the CLIP top hinges
or loosen them if using COMPACT.▀

4 Removing the telescopic arms

Using a screwdriver, depress the release tabs to remove telescopic arms.

If transporting the cabinet to the jobsite, stop here. Lift mechanisms stay inside the cabinet for easy transport.

22

Subject to technical modifications without notice. © 2018 11

 Other information

Door clearance above cabinet Inch mm

1 32
/ .031 1

Z = TDH x .44 + 38 1
/16 .063 1.5
H
TD
Z

3 32
/ .094 2
18
/ .125 3
5 32
/ .156 4
3 16
/ .188 5
7 32
/ .219 5.5
14
/ .25 6
9 32
/ .281 7
5 16
/ .313 8
11
/32 .344 9
3 8
/ .375 9.5
13 32
/ .406 10
7 16
/ .438 11
15 32
/ .469 12
12
/ .5 13
17 32
/ .531 13.5
9 16
/ .563 14
19 32
/ .594 15
58
/ .625 16
21 32
/ .656 17
11 16
/ .688 17.5
23 32
/ .719 18
34
/ .75 19
25 32
/ .781 20
13 16
/ .813 20.5
27 32
/ .844 21
78
/ .875 22
Blum, Inc. 29 32
/ .906 23
800-438-6788
[email protected] 15 16
/ .938 24
blum.com
31 32
/ .969 24.5

Subject to technical modifications without notice. © 2018 INST-AVT04-04.15 1 1 25.4