Session Plan

Sector : Electronics
Qualification Title : Electronic Products Assembly and Servicing NC II
Unit of Competency : Assemble Electronic Products
Module Title : Assembling Electronic Products

Learning Outcomes:
LO1. Prepare to assemble electronic products
LO2. Prepare/Make PCB Modules
LO3. Mount and solder electronic components
LO4. Assemble electronic products
LO5. Test and inspect electronic products
A. Introduction:
This module covers the knowledge, skills and attitudes required to assemble electronic products and systems for
consumer/industrial uses/applications.

B. Learning Activities
LO2. PREPARE / MAKE PCB MODULE
Learning Content Methods Presentation Practice Feedback Resources Time
1. Prepare in PCB Self-Study Read Information Answer Self- Compare -Information 1hr
Designing Sheet. 1.2-1; Check No. 1.2-1 answer to Sheet No. 1.2-1
Procedure in Answer Key of CBLM
PCB Designing No. 1.2-1
Discussion Listen to the Perform Activity Check -white screen 2hrs
trainer while he sheet No.1.2-1; individual -laptop
discuss the topic works using -projector
about Procedure performance -service manual
in PCB criteria -Power point
Designing checklist presentation
 about the parts
of an industrial
washing
machine
Video Pay attention to Answer Guide The model -white screen 1hr
Showing the video and questions answer will -laptop
take down notes. be given by -projector
the trainer -Video
Presentation
about
Procedure in
PCB Designing
2. Procedure in PCB Self-Study Read Information Answer Self- Compare -Information 1hr
Layouting Sheet. 1.2-2; Check No. 1.2-2 answer to Sheet No. 1.2-2
Answer Key of CBLM
No. 1.2-2
Discussion Listen to the Perform Task Check -Service 2hrs
trainer while he Sheet No. 1.2-2; Individual manuals
discuss the topic Retrieving the works using -white screen
about Procedure main control performance -laptop
in PCB board of an criteria -projector
Layouting . industrial checklist -PowerPoint
washing presentation
machine about
Schematic &
block diagram
of an Industrial
Washing
Machine
Video Pay attention to Answer Guide The model -white screen 1hr
Showing the video and questions answer will -laptop
take down notes. be given by -projector
 the trainer -Video
Presentation
about PCB
Layouting
3. Procedure in PCB Self-Study Read Information Answer Self- Compare -Information 1hr
Etching Sheet No. 1.2-3; Check No. 1.2-3 answer to Sheet No. 1.2-3
Procedure in Answer Key of CBLM
PCB Etching No. 1.2-3
Discussion Listen to the Perform Task Check -white screen 1hr
trainer while he sheet 1.2-3 Individual -laptop
discusses the works using -projector
topic regarding performance -service manual
Acceptable criteria -Power point
methods… checklist presentation
about control
boards and
motor controller
4. Procedure in PCB Self-Study Read Information Answer Self- Compare -Information 1hr
Drilling Sheet No. 1.2-4; Check No. 1.2-4 answer to Sheet No. 1.2-4
Procedure in Answer Key of CBLM
PCB Drilling No. 1.2-4
Video Pay attention to Answer Guide The model -white screen 1hr
Showing the video and questions answer will -laptop
take down notes. be given by -projector
the trainer -Video
Presentation
about the
different
equipment in
testing and
inspecting
industrial
 modules
C. Assessment Plan
Please refer to evidence plan.
D. Teacher’s Self-Reflection of the Session
The trainees are active and very cooperative during activities. The delivery of the contents went well and was accomplished on
time according to the planned session. Based on the result of the assessment of the trainees they can now;
 Prepare unit, tools and workplace for installation/ servicing.
 Install industrial electronic modules/ products/ systems.
 Diagnose faults and defects of industrial electronic modules/ products/ systems.
 Maintain/ Repair industrial electronic products.
 Reassemble and test repaired industrial electronic products.
Prepared by:

_____________
EPAS-Instructor