Scribd
Upload
73 views3 pages

Annex 1slab Desing

The document provides preliminary design details for a continuous slab, including dimensions, material properties, and loading conditions. Calculations are shown to determine design moments at supports and midspans for the short and long spans. Checking ensures the concrete depth is sufficient. Main reinforcement areas and spacing are selected based on the required areas to resist the calculated bending moments.

Uploaded by

Surendra Maharjan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
73 views3 pages

Annex 1slab Desing

The document provides preliminary design details for a continuous slab, including dimensions, material properties, and loading conditions. Calculations are shown to determine design moments at supports and midspans for the short and long spans. Checking ensures the concrete depth is sufficient. Main reinforcement areas and spacing are selected based on the required areas to resist the calculated bending moments.

Uploaded by

Surendra Maharjan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Slab Design

Preliminary Design

Longer Span (ly) 4.98 m


Shorter Span (lx) 4.65 m
End supports Continuous Slab
Span 4.65 m
Clear Cover d' 20.00 mm
Reinforcement Grade Fe 500
Bar diameter Ø 8.00 mm
Span/deff BVxSxmf txmfcxmff
Basic Value of span/deff BV 26.00 IS 456 Cl. 23.2.1
Span Correction Factor 1.00
Assume % of rension reinforcement 0.30
Assume % of compression reinforcement 0.00
bw/bf 1.00
MFt, Modification Factor for Tension Steel 1.50 IS 456 Fig. 4
MFc, Modification Factor for Compression Steel 1.00
MFf, Reduction Factor for bw/bf 1.00
MF 1.50
deff 119.18 mm
Overall depth 143.18 mm
Assume Overal depth 127.00 mm

Basic Span depth Ratio 32


Modification Factor 0.8
Effective Depth required d eff 182 mm
Adopt Overall Depth D 150 mm
Adopted Span Depth ratio 35.75
Required Modification Factor 1.117
Design
Slab thickness D 127 mm Sunken Depth 325 mm
Concrete fck 20 MPa
Steel fy 500 MPa

Loading
Slab Load Sunken Slab Load
Dead Load DL 3.18 KN/m Dead Load DL 3.175 KN/m
Live Load LL 7.50 KN/m IS 875 Part 2, Storage Building Filler Load FL 5 KN/m
Finishes Load FF 1.00 KN/m Live Load LL 3.0 KN/m
Partition Load 1.00 KN/m Finishes Load WL 1.0 KN/m
Total Load Ws 12.675 KN/m Total Load Wsk 11.79 KN/m
Factored Load Wu 19.0 KN/m 1m width strip of Slab Factored Load Wsku 18 KN/m

Slab Data
Slab Type Regular
Load 19 KN/m
Longer Span Ly 4.98 m ly/lx ratio 1.07
Shorter Span Lx 4.65 m Slab type +
Types of Slab Panel Interior Panel

Loading on edges one way two way


W longer 2
31 KN/m .=w*lx/2 .=(w*lx/2) + (1-(1/3)*(lx/ly) )
W shorter 29 KN/m .=w*lx/3

Design Moments one way two way


Short Span Moment (Mx)
2
At Support M' ux -16 KN-m .= α'x * w*lx
2 2
At Midspan M ux 21 KN-m .=w*lx / 8 .= αx * w*lx
Long Span Moment (My)
At Support M' uy -14 KN-m .= α'y*w*lx 2
2
At Midspan M uy 19 KN-m .= αy*w*lx

Check for concrete depth


Thickness Check OK .=Mulim > Mux or Muy
d 87 mm
Deflection 40 mm .= 5*W*l 4 /(384EI)

Main Steel
Astx Asty Refer Chart 4 SP 16 pg 21 or
Area of Steel
152 sqmm 466 sqmm Refer Table 5-44 SP 16 pg 51-80

Spacing required in mm
8.00 Ø 10.00 Ø 12.00 Ø 16.00 Ø
x y x y x y x y
108 c/c 169 c/c 243 c/c 432 c/c
.=ast of bar*1000/ast req

x y
Final Ast provided
150 c/c 150 c/c

You might also like